Document ID | Title | Date |
---|---|---|
DOE-HDBK-1131-2007 |
General Employee Radiological Training This handbook describes the DOE General Employee Radiological Training program. It is intended for use by DOE contractors for the development of facility-specific general employee radiological training. |
01/15/2008 |
DOE-HDBK-1131-98 |
General Employee Radiological Training This handbook describes the DOE General Employee Radiological Training program. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE contractors for the development of facility-specific general employee radiological training. |
03/26/2004 |
DOE-DP-STD-3016-99 |
Limited Standard; Hazard Analysis Reports for Nuclear Explosive Operations This technical standard applies to the conduct of hazard analyses and preparation of hazard analysis reports (HARs) for nuclear explosive operations (NEOs) conducted by the Department of Energy (DOE). This standard addresses operation-specific HARs and their interface with facility safety basis documents (Safety Analysis Reports [SARs] or other DOE-approved safety basis documents). |
02/26/1999 |
DOE-EM-STD-5502-94 |
Hazard Baseline Documentation This standard establishes uniform Office of Environmental Management (EM) guidance on hazard baseline documents that identify and control radiological and non-radiological hazards for all EM facilities. |
12/04/1995 |
DOE-EM-STD-5505-96 |
DOE Limited Standard Operations Assessments |
05/24/1996 |
DOE-ER-STD-6001-92 |
Implementation Guide for Quality Assurance Programs for Basic and Applied Research This Implementation Guide is intended to assist management at DOE-ER sponsored facilities in the process of developing and implementing Quality Assurance Programs (QAPs) that satisfy the requirements of DOE Order 5700.6C. |
03/12/1996 |
DOE-HDBK-1001-96 |
Guide to Good Practices for Training and Qualification of Instructors This guide contains good practices for the training and qualification of technical instructors and instructional technologist at DOE reactor and non-reactor nuclear facilities. |
05/15/1996 |
DOE-HDBK-1002-96 |
Guide to Good Practices for Training and Qualification of Chemical Operators The purpose of the Guide to Good Practices for Training and Qualification of Chemical Operators is to provide contractor training organizations with information that can be used as a reference to refine existing chemical operator training programs, or develop new training programs where no program exists. |
05/14/1996 |
DOE-HDBK-1003-96 |
Guide to Good Practices for Training and Qualification of Maintenance Personnel This guide provides recommended education, experience, and training for maintenance personnel. Training and qualification programs based on the content of this guide should provide assurance that maintenance personnel perform their jobs safely and competently. |
05/15/1996 |
DOE-HDBK-1010-92 |
DOE Fundamentals Handbook, Classical Physics The handbook includes information on the units used to measure physical properties; vectors, and how they are used to show the net effect of various forces; Newton's Laws of motion, and how to use these laws in force and motion applications; and the concepts of energy, work, and power, and how to measure and calculate the energy involved in various applications |
09/27/1995 |
DOE-HDBK-1011/1-92 |
DOE Fundamentals Handbook, Electrical Science, Volume 1 of 4 The Department of Energy Fundamentals Handbook entitled Electrical Science was prepared as an information resource for personnel who are responsible for the operation of the Department's nuclear facilities. A basic understanding of electricity and electrical systems is necessary for DOE nuclear facility operators, maintenance personnel, and the technical staff to safely operate and maintain the facility and facility support systems |
01/18/2006 |
DOE-HDBK-1011/2-92 |
DOE Fundamentals Handbook, Electrical Science, Volume 2 of 4 The handbook includes information on alternating current (AC) and direct current (DC) theory, circuits, motors, and generators; AC power and reactive components; batteries; AC and DC voltage regulators; transformers; and electrical test instruments and measuring devices. |
01/29/1996 |
DOE-HDBK-1011/3-92 |
DOE Fundamentals Handbook, Electrical Science, Volume 3 of 4 This information will provide personnel with a foundation for understanding the basic operation of various types of DOE nuclear facility electrical equipment. |
01/16/1996 |
DOE-HDBK-1011/4-92 |
DOE Fundamentals Handbook, Electrical Science, Volume 4 of 4 The Electrical Science Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of electrical theory, terminology, and application. |
01/10/1996 |
DOE-HDBK-1012/1-92 |
DOE Fundamentals Handbook, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 1 of 3 This module explains the properties of fluids and how those properties are affected by various processes. The module also explains how energy balances can be performed on facility systems or components and how efficiency can be calculated. |
01/19/1996 |
DOE-HDBK-1012/2-92 |
DOE Fundamentals Handbook, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 2 of 3 This module describes conduction, convection, and radiation heat transfer. The module also explains how specific parameters can affect the rate of heat transfer. |
01/22/1996 |
DOE-HDBK-1012/3-92 |
DOE Fundamentals Handbook, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3 of 3 This module describes the relationship between the different types of energy in a fluid stream through the use of Bernoulli's equation. The module also discusses the causes of head loss in fluid systems and what factors affect head loss |
01/26/1996 |
DOE-HDBK-1013/1-92 |
DOE Fundamentals Handbook, Instrumentation and Control, Volume 1 of 2 The Instrumentation and Control Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of instrumentation and control systems. |
01/24/1996 |
DOE-HDBK-1013/2-92 |
DOE Fundamentals Handbook, Instrumentation and Control, Volume 2 of 2 The handbook includes information on temperature, pressure, flow, and level detection systems; position indication systems; process control systems; and radiation detection principles. |
01/26/1996 |
DOE-HDBK-1014/1-92 |
DOE Fundamentals Handbook, Mathematics Volume 1 of 2 The Mathematics Fundamentals Handbook was developed to assist nuclear facility operating contractors provide operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of mathematics and its application to facility operation. |
01/22/1996 |
DOE-HDBK-1014/2-92 |
DOE Fundamentals Handbook, Mathematics Volume 2 of 2 The handbook includes a review of introductory mathematics and the concepts and functional use of algebra, geometry, trigonometry, and calculus. Word problems, equations, calculations, and practical exercises that require the use of each of the mathematical concepts are also presented |
01/23/1996 |
DOE-HDBK-1015/1-93 |
DOE Fundamentals Handbook, Chemistry, Volume 1 of 2 The handbook includes information on the atomic structure of matter; chemical bonding; chemical equations; chemical interactions involved with corrosion processes; water chemistry control, including the principles of water treatment; the hazards of chemicals and gases, and basic gaseous diffusion processes. |
01/30/1996 |
DOE-HDBK-1015/2-93 |
DOE Fundamentals Handbook, Chemistry, Volume 2 of 2 The Chemistry Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of chemistry. |
01/30/1996 |
DOE-HDBK-1016/1-93 |
DOE Fundamentals Handbook, Engineering Symbology, Prints, and Drawings, Volume 1 of 2 The Engineering Symbology, Prints, and Drawings Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and technical staff with the necessary fundamentals training to ensure a basic understanding of engineering prints, their use, and their function. |
06/21/2006 |
DOE-HDBK-1016/2-93 |
DOE Fundamentals Handbook, Engineering Symbology, Prints, and Drawings, Volume 2 of 2 |
02/12/1996 |
DOE-HDBK-1017/1-93 |
DOE Fundamentals Handbook, Material Science, Volume 1 of 2 The Material Science Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of the structure and properties of metals. |
06/27/1996 |
DOE-HDBK-1017/2-93 |
DOE Fundamentals Handbook, Material Science, Volume 2 of 2 The handbook includes information on the structure and properties of metals, stress mechanisms in metals, failure modes, and the characteristics of metals that are commonly used in DOE nuclear facilities. |
02/09/1996 |
DOE-HDBK-1018/1-93 |
DOE Fundamentals Handbook, Mechanical Science, Volume 1 of 2 The Mechanical Science Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of mechanical components and mechanical science. |
07/10/1996 |
DOE-HDBK-1018/2-93 |
DOE Fundamentals Handbook, Mechanical Science, Volume 2 of 2 The handbook includes information on diesel engines, heat exchangers, pumps, valves, and miscellaneous mechanical components. |
07/15/1996 |
DOE-HDBK-1019/1-93 |
DOE Fundamentals Handbook, Nuclear Physics and Reactor Theory, Volume 1 of 2 The Nuclear Physics and Reactor Theory Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and the technical staff with the necessary fundamentals training to ensure a basic understanding of nuclear physics and reactor theory. |
07/18/1996 |
DOE-HDBK-1019/2-93 |
DOE Fundamentals Handbook, Nuclear Physics and Reactor Theory, Volume 2 of 2 The handbook includes information on atomic and nuclear physics; neutron characteristics; reactor theory and nuclear parameters; and the theory of reactor operation. |
07/18/1996 |
DOE-HDBK-1046-2008 |
Temporary Emergency Exposure Limits for Chemicals: Methods and Practice This order, and its Guides issued in 2007, reference Acute Exposure Guideline Levels (AEGLs) and Emergency Response Planning Guidelines (ERPGs) as the emergency exposure limits of choice. This document describes why TEELs are needed, their role in emergency planning in DOE, the history of their development, and the methods by which they are developed. |
08/21/2008 |
DOE-HDBK-1074-95 |
Alternative Systematic Approaches to Training The use of guidance on selection and implementation of appropriate training approaches after consideration of job complexity, the consequences of error based on risk/hazard potential, and available training media should result in effective and efficient training programs. |
11/21/1995 |
DOE-HDBK-1078-94 |
Training Program Handbook: A Systematic Approach to Training This Handbook contains a narrative discussion on the various phases of the systematic approach to training process. The phases can be modified and incorporated as appropriate when developing detailed local procedures. Each phase is organized such that the major steps necessary to adequately complete it are clear. |
10/25/1995 |
DOE-HDBK-1079-94 |
Primer on Tritium Safe Handling Practices Tritium Safe Handling Practices was prepared as an information resource for personnel who perform tritium handling functions at DOE facilities. A basic understanding of the properties and hazards associated with tritium will help personnel understand the impact of their actions on the safe and reliable operation of facility systems. |
12/13/1995 |
DOE-HDBK-1080-97 |
Guide to Good Practices for Oral Examinations This Primer is intended to help operations and maintenance personnel perform their duties safely by increasing their knowledge of tritium handling and control, thus reducing the likelihood of tritium releases and exposures, and by providing basic emergency responses in the case of a tritium release. |
12/01/1997 |
DOE-HDBK-1081-94 |
Primer on Spontaneous Heating and Pyrophoricity The purpose of this Primer is to provide operations and maintenance personnel with the information necessary to identify and prevent potential spontaneous combustion hazards. Throughout the history of industry and the DOE Complex, fires caused by spontaneously heating and pyrophoric materials have occurred, sometimes causing personal injury and significant damage to facilities. |
11/22/1995 |
DOE-HDBK-1084-95 |
Primer on Lead-Acid Storage Batteries The handbook was developed to help DOE facility contractors prevent accidents caused during operation and maintenance of lead-acid storage batteries. Safety hazards and precautions are discussed in the section on battery maintenance. |
01/05/1996 |
DOE-HDBK-1086-95 |
Table-Top Training Program Design Table-Top methods can be used for many purposes, but the focus of this Handbook is on training program design. Department of Energy (DOE) Order 5480.20A, Personnel Selection, Qualification, and Training Requirements for DOE Nuclear Facilities, stresses the importance of training programs that are based on a systematic approach. |
07/10/1996 |
DOE-HDBK-1092-1998 |
Electrical Safety This document contains DOE developed explanatory material in support of OSHA regulations and nationally recognized electrical safety related standards and other information. This document was revised to include electrical safety for enclosed electrical and electronic equipment, research and development. |
03/07/1998 |
DOE-HDBK-1092-2004 |
Electrical Safety The Electrical Safety Handbook presents the Department of Energy (DOE) safety standards for DOE field offices or facilities involved in the use of electrical energy. It has been prepared to provide a uniform set of electrical safety guidance and information for DOE installations to effect a reduction or elimination of risks associated with the use of electrical energy. The objectives of this handbook are to enhance electrical safety awareness and mitigate electrical hazards to employees, the public, and the environment. |
12/17/2004 |
DOE-HDBK-1099-96 |
Establishing Nuclear Facility Drill Programs The purpose of DOE Handbook, Establishing Nuclear Facility Drill Programs, is to provide DOE contractor organizations with guidance for development or modification of drill programs that both train on and evaluate facility training and procedures dealing with a variety of abnormal and emergency operating situations likely to occur at a facility. |
05/14/1996 |
DOE-HDBK-1101-96 |
Process Safety Management for Highly Hazardous Chemicals This handbook provides information necessary to determine if a chemical process is covered by the PSM Rule and provides an interpretation of the 14 elements of the PSM Rule. An overview of these elements is given in Table 1.1. This handbook also describes DOE programs that may, with or without modification, satisfy the requirements of this Rule. |
05/17/1996 |
DOE-HDBK-1103-96 |
Table-Top Needs Analysis This Handbook guides the conduct of table-top needs analysis. An overview of needs analysis is provided and is followed by a detailed explanation of the table-top needs analysis method. The appendixes include facilitator and coordinator materials to provide further information and examples of table-top needs analysis. |
01/28/1997 |
DOE-HDBK-1105-2002 |
Radiological Training for Tritium Facilities, The goal of the training program is to provide a baseline knowledge for those individuals completing the training. Use of the DOE developed material provides personnel with the information necessary to perform their assigned duties at a predetermined level of expertise. Implementing the training program helps ensure consistent and appropriate training of personnel |
02/05/2002 |
DOE-HDBK-1105-2002 |
Radiological Training for Tritium Facilities This Handbook describes a recommended implementation process for conducting the radiation safety training required by Title 10 Code of Federal Regulations Occupational Radiation Protection, (10 CFR 835) Subpart J and as outlined in the DOE standard DOE-STD-1098-99, Radiological Control (RCS). The Handbook is to assist those individuals, both within the Department of Energy (DOE) and Managing and Operating (M&O) contractors, identified as having responsibility for implementing the training required by 10 CFR 835 and recommended by the RCS |
12/07/2006 |
DOE-HDBK-1106-1997 |
Radiological Contamination Control Training for Laboratory Research This program management guide describes the proper implementation standard for core training as outlined in the DOE Radiological Control (RadCon) Standard. |
12/07/2006 |
DOE-HDBK-1106-97 |
Radiological Contamination Control Training for Laboratory Research This program management guide describes the proper implementation standard for core training as outlined in the DOE Radiological Control (RadCon) Standard. The guide is to assist those individuals, both within the Department of Energy (DOE) and Managing and Operating (M&O) contractors, identified as having responsibility for implementing the core training recommended by the RadCon Standard. |
12/07/2006 |
DOE-HDBK-1106-97 |
Radiological Contamination Control Training for Laboratory Research This program management guide describes the proper implementation standard for core training as outlined in the DOE Radiological Control (RadCon)Standard. The guide is to assist those individuals, both within the Department of Energy (DOE) and Managing and Operating (M&O) contractors, identified as having responsibility for implementing the core training recommended by the RadCon Standard. |
10/02/2002 |
DOE-HDBK-1108-2002 |
Radiological Safety Training for Accelerator Facilities This non-mandatory Handbook describes a recommended implementation process for conducting the radiation safety training required by Title 10 Code of Federal Regulations Occupational Radiation Protection, (10 CFR 835) Subpart J and as outlined in the DOE standard DOE-STD-1098-99, Radiological Control (RCS). The Handbook is to assist those individuals, both within the Department of Energy (DOE) and Managing and Operating (M&O) contractors, identified as having responsibility for implementing the training required by 10 CFR 835 and recommended by the RCS |
12/07/2006 |
DOE-HDBK-1109-97 |
Radiological Safety Training for Radiation-Producing This program management guide provides guidance for proper implementation of additional standardized training as outlined in the DOE Radiological Control Standard (RCS). |
01/26/2007 |
DOE-HDBK-1109-97 |
Radiological Safety Training for Accelerator Facilities This Handbook describes a recommended implementation process for additional standardized training as outlined in the DOE Radiological Control Standard (RCS). |
03/15/2002 |
DOE-HDBK-1110-97 |
ALARA Training for Technical Support Personnel This memorandum forwards changes to subject DOE Technical Standard, DOE-HDBK-1110-97. The changes were made as part of the Office of Worker Protection Policy and Programs updating the Word Processing software used to develop and maintain the document (i.e., conversion from WordPerfect to Word). The attached table details the editorial changes. The document had just been reaffirmed in July 2002. |
11/29/2004 |
DOE-HDBK-1113-2008 |
Radiological Safety Training for Uranium Facilities This Handbook describes a recommended implementation process for additional training as outlined in DOE-STD-1098-99, Radiological Control (RCS). Its purpose is to assist those individuals, Department of Energy (DOE) employees, Managing and Operating (M&O) contractors, and Managing and Integrating (M&I) contractors identified as having responsibility for implementing the training recommended by the RCS. |
04/14/2008 |
DOE-HDBK-1113-98 |
Radiological Safety Training for Uranium Facilities With this memorandum and the attached table of changes, DOE-HDBK-1113-98 is considered to be ready for reissuing. |
05/10/2005 |
DOE-HDBK-1114-98 |
DOE-HDBK-1114-98: Guide to Good Practices for Line and Training Manager Activities The purpose of this guide is to provide direction for line and training managers in carrying out their responsibilities for training and qualifying assigned personnel and to verify that existing training activities are effective. |
08/13/1997 |
DOE-HDBK-1115-98 |
Guide to Good Practices for the Selection, Training, and Qualification of Shift Technical Advisors The purpose of this guide is to provide information on the STA training and qualification program. The guide is based on STAs being assigned specific responsibilities and duties within the shift crew. |
01/21/1999 |
DOE-HDBK-1116-98 |
Guide to Good Practices for Developing and Conducting Case Studies This guide contains a method for learning from experience to prevent mistakes from occurring; that method is the case study. |
05/19/1998 |
DOE-HDBK-1117-99 |
Guide to Good Practices for Maintenance Supervisor Selection and Development This guide has been developed based on functional responsibilities typical of the electrical, instrument and control, mechanical, and maintenance supervisor positions. This guide applies to all levels of maintenance supervision, up to but not including the maintenance manager. |
11/18/1999 |
DOE-HDBK-1118-99 |
Guide to Good Practices for Continuing Training This guide provides contractor training organizations with information and methods useful in the development and implementation of continuing training programs using a Systematic Approach to Training (SAT) process. |
01/19/1999 |
DOE-HDBK-1119-99 |
Guide to Good Practices for the Selection, Training, and Qualification of Shift Supervisors This guide, used in conjunction with a facility-specific job analysis, provides a framework for the selection, training, qualification, and professional development of reactor facility and non-reactor nuclear facility shift supervisors. Training and qualification programs based on this guide should provide assurance that shift supervisors perform their jobs safely and competently. |
04/20/1999 |
DOE-HDBK-1122-2009 |
Radiological Control Technician Training This guide defines and describes the DOE Radiological Control Technician (RCT) Core Training & Qualification Program, material development requirements, standards and policies, and administration. The guide applies to RCT Training & Qualification Programs at all DOE sites |
03/11/2009 |
DOE-HDBK-1122-99 |
Fundamental Academic Training Instructor's Guide Phase I Due to the large size of this document it has been broken down into smaller PDF files. Includes detailed Table of Contents, Introduction, Training and Qualification Program Description , Site Training Program Development, Evaluation, Administration and References |
07/21/1999 |
DOE-HDBK-1129-2007 |
Tritium Handling and Safe Storage Tritium handling practices have evolved over several decades at Department of Energy tritium facilities. The objective has been to accomplish required tritium work while minimizing and controlling the exposure of workers, the public, and the environment from tritium. This document provides guidance for the handling, storing and shipping of tritium. |
05/04/2007 |
DOE-HDBK-1129-2008 |
Tritium Handling and Safe Storage This Handbook can be used by personnel involved in the full range of tritium handling, from receipt to ultimate disposal. Compliance issues are addressed at each stage of handling. This Handbook can also be used as a reference for those individuals involved in real-time determination of bounding doses resulting from inadvertent tritium releases. |
01/30/2009 |
DOE-HDBK-1129-99 |
Fundamental Academic Training Instructor's Guide Phase I; Module 1.03 - Physical Sciences Tritium handling practices have evolved over several decades at Department of Energy tritium facilities. The objective has been to accomplish required tritium work while minimizing and controlling the exposure of workers, the public, and the environment from tritium. This document provides guidance for the handling, storing and shipping of tritium. Literature references furnish information current through mid-1998. |
07/21/1999 |
DOE-HDBK-1130-2007 |
Radiological Worker Training This guide describes the DOE Radiological Worker I and II (RW I and II) training programs. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by the DOE and DOE contractors for the development of facility/site-specific radiological worker training. |
12/11/2007 |
DOE-HDBK-1130-2008 |
Radiological Worker (RW) Training This program management guide provides guidance for proper implementation of additional standardized raining as outlined in the DOE Radiological Control Standard (RCS). |
12/11/2008 |
DOE-HDBK-1130-98 |
Radiological Worker Training This guide describes the DOE Radiological Worker I and II (RW I and II) training programs. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE contractors for the development of facility-specific radiological worker training. |
05/04/2004 |
DOE-HDBK-1130-98 |
Radiological Worker Training This guide describes the DOE Radiological Worker I and II (RW I and II) training programs. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE contractors for the development of facility-specific radiological worker training. |
12/04/2003 |
DOE-HDBK-1131-2007 |
General Employee Radiological Training This handbook describes the DOE General Employee Radiological Training program. It is intended for use by DOE contractors for the development of facility-specific general employee radiological training. |
08/05/2009 |
DOE-HDBK-1132-99 |
Design Considerations Replaced by DOE-STD-1132-1999 (Reaffirmed 2014) The Design Considerations Handbook includes information and suggestions for the design of systems typical to nuclear facilities, information specific to various types of special facilities, and information useful to various design disciplines. |
05/21/1999 |
DOE-HDBK-1139/1-00 |
Chemical Management Why a DOE Chemical Management Handbook? Chemicals are ubiquitous in DOE’s nuclear and non-nuclear operations. Given their wide application, it is not surprising that chemical incidents or exposures continue at a rate of approximately one a day. With respect to major accidents, chemicals are the second leading cause of DOE Type A & B accidents, exceeded only by those attributed to radiation. |
09/13/2004 |
DOE-HDBK-1139/2-02 |
Chemical Manager Volume 2 presents a description of the chemical management practices as individually developed at several Department of Energy (DOE) facilities. These are formatted according to the order presented in Volume 1 of the Handbook, published by the Chemical Safety Topical Committee (CSTC) in November 2000. Electronic inventory tracking, automated Material Safety Data Sheet (MSDS) systems, and Hazard Communication training are common among all Sites. |
08/06/2002 |
DOE-HDBK-1139/3-03 |
Chemical Management (Volume 3 of 3) This Department of Energy Handbook was prepared under the sponsorship of the joint Department of Energy (DOE)/Energy Facility Contractors Group (EFCOG) Chemical Safety Topical Committee (CSTC). It was prepared over a span of four years by the CSTC’s Chemical User Safety and Health Requirements Roadmap team (the CUSHR team), consisting of representatives from several sites and DOE headquarters, chaired by Dr. Dave Quigley, Idaho National Engineering and Environmental Laboratory and co-chaired by Mr. James Morgan, Westinghouse Savannah River Company and Ms. Gail Kleiner, DOE/EH-52. |
10/23/2003 |
DOE-HDBK-1139/3-2005 |
Chemical Management This chapter identifies and consolidates existing user safety and health requirements found in DOE and Federal chemical-related safety and health regulations and National Standards that address hazard analysis of activities involving chemicals (see definition) and chemical products (see definition). State and local codes and requirements are NOT included. |
04/14/2005 |
DOE-HDBK-1141-2001 |
Radiological Assessor Training This Handbook describes an implementation process for training as recommended in Implementation Guide G441.1-12, Radiation Safety Training Guide, and as outlined in DOE STD- 1098-99 DOE Radiological Control (the Radiological Control Standard - RCS). The Handbook is meant to assist those individuals within the Department of Energy, Managing and Operating contractors, and Managing and Integrating contractors identified as having responsibility for implementing training required by Title 10 Code of Federal Regulations Part 835 Occupational Radiation Protection (10 CFR 835) and training recommended by the RCS. |
05/09/2001 |
DOE-HDBK-1141-2008 |
Radiological Assessor Training Canceled, Effective July 2016 This handbook describes a Radiological Assessor Training program. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE and DOE contractors for the development of facilityspecific radiological assessor training. This material is intended for assessment of occupational radiation protection programs. |
08/20/2008 |
DOE-HDBK-1143-2001 |
Radiological Control Training for Supervisors This handbook describes a Radiological Control Training for Supervisors program. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE and DOE contractors for the development of facility-specific radiological control training for supervisors. |
12/07/2006 |
DOE-HDBK-1143-2001 |
Radiological Control Training for Supervisors This handbook describes a Radiological Control Training for Supervisors program. It includes standards and policies as well as recommendations for material development and program administration. It is intended for use by DOE and DOE contractors for the development of facility-specific radiological control training for supervisors. |
08/20/2001 |
DOE-HDBK-1145-2001 |
Radiological Safety Training for Plutonium Facilities This program management guide describes the proper implementation standard for core training as outlined in the DOE Radiological Control (RadCon) Standard. |
08/21/2001 |
DOE-HDBK-1145-2008 |
Radiological Safety Training for Plutonium Facilities This program management guide describes the proper implementation standard for core training as outlined in the DOE Radiological Control (RadCon) Standard. |
08/20/2008 |
DOE-HDBK-1148-2002 |
Work Smart Standards (WSS) Users Handbook A set of Work Smart Standards (WSS) is the product of the Necessary and Sufficient Closure Process. This Handbook provides amplification, practical examples, and cross references to assist users in the application of the Necessary and Sufficient (N&S) Closure Process within the context of the Integrated Safety Management System (ISMS)1. |
02/27/2002 |
DOE-HDBK-1184-2004 |
Radiological Control Programs for Special Tritium Compounds Handbook Tritium compounds may exhibit unique properties when ingested, absorbed, or inhaled into the human body. As a result of these unique behaviors, specific guidance is being provided to facilitate the development and implementation of appropriate protective programs. |
05/23/2006 |
DOE-HDBK-1200-97 |
Guide to Good Practices for Developing Learning Objectives This guide to good practices provides information and guidance on the types of and development of learning objectives in a systematic approach to training (SAT) program. |
03/14/1997 |
DOE-HDBK-1201-97 |
Guide to Good Practices: Evaluation Instrument Examples This guide provides information on evaluation instruments used to gather employee, supervisor, and instructor feedback to identify strengths and weaknesses of training programs at DOE facilities. It should be used in conjunction with DOE Training Program Handbook: A Systematic Approach to Training and DOE Handbook, Alternative Systematic Approaches to Training. |
01/08/1997 |
DOE-HDBK-1202-97 |
Guide to Good Practices for Teamwork Training and Diagnostic Skills Development This guide provides assistance in the development, implementation, and improvement of training on teamwork and diagnostics. DOE and contractor representatives identified the need for teamwork and diagnostics training guidance. This need was based on the increasing emphasis of properly applying knowledge and skills to complete assigned tasks. Teamwork and diagnostic skills have become a focal point because of the impact they have on effective facility operation and safety. |
07/26/2005 |
DOE-HDBK-1203-97 |
Guide to Good Practices for Training of Technical Staff and Managers Training programs at Department of Energy (DOE) facilities should prepare personnel to safely and efficiently operate the facilities in accordance with DOE requirements. This guide contains information that can be used to develop or validate training programs for technical staff and managers at DOE nuclear facilities. Training programs based on the content of this guide should provide assurance that these personnel perform their jobs safely and competently. |
04/07/2007 |
DOE-HDBK-1204-97 |
Guide to Good Practices for the Development of Test Items While the methodology used in developing test items can vary significantly, to ensure quality examinations, test items should be developed systematically. Test design and development is discussed in the DOE Guide to Good Practices for Design, Development, and Implementation of Examinations. |
07/26/2005 |
DOE-HDBK-1205-97 |
Guide to Good Practices for the Design, Development, and Implementation of Examinations The purpose of this Guide to Good Practices is to provide direction to training personnel in the broad areas of design, development, and implementation of examinations. |
07/27/2005 |
DOE-HDBK-1206-98 |
Guide to Good Practices for On-the-Job Training This guide presents good practices for a systematic approach to on-the-job training (OJT) and OJT programs. DOE contractors may also use this guide to modify existing OJT programs that do not meet the systematic approach to training (SAT) objectives. |
07/27/2005 |
DOE-HDBK-1213-2014 |
Protective Force Contingency Planning Technical Standard The Protective Force Contingency Planning Technical Standard outlines the responsibilities, planning considerations, training, management oversight, and other activities related to establishment of a Contingency Protective Force. |
07/22/2014 |
DOE-HDBK-3010-94 |
Airborne Release Fractions/Rates and Respirable Fractions for Nonreactor Nuclear Facilities The purpose of this document is to provide a compendium and analysis of experimental data from which airborne release fractions (ARFs) and respirable fractions (RFs) may be derived. Such values are needed to determine quantities of radioactive material driven airborne for the purpose of estimating the scope of the potential release spectrum and potential downwind consequences from a given facility or activity. |
03/22/2000 |
DOE-HDBK-3012-2003 |
Guide To Good Practices For Operational Readiness Reviews (ORR), Team Leader's Guide This guidance provides instructions, explanations and examples for the performance of all phases of an Operational Readiness Review (ORR). Details pertinent to the Team Leader, Team Members, and Review Coordinator are outlined. Appendices contain sample forms and correspondence, which are typically used to initiate and perform the ORR. |
11/26/2003 |
DOE-HDBK-3012-96 |
Guide to Good Practices For Operational Readiness Reviews This guidance section provides instructions, explanations and examples for the performance of all phases of an Operational Readiness Review (ORR). Details pertinent to the Team Leader (TL), Team Members (TM) and Review Coordinator (RC) are outlined. An appendix contains sample forms and correspondence which are typically used to initiate and perform the ORR. |
09/17/1996 |
DOE-HDBK-5504-95 |
Guidance for Evaluation of Operational Emergency Plans The purpose of this document is to provide guidance for development of emergency plans for the U.S. Department of Energy (DOE) Office of Defense Programs (DP), Office of Energy Research (ER), and Office of Environmental Management (EM) facilities. |
09/05/1995 |
DOE-HDBK-7502-95 |
Implementing U.S. Department of Energy Lessons Learned Programs The purpose of this Department of Energy (DOE) Lessons Learned Handbook is to provide DOE and DOE contractor organizations with information that can be used to modify existing lessons learned programs or to develop new programs. |
10/30/1995 |
DOE-NA-STD-3016-2006 |
Hazard Analysis Reports for Nuclear Explosive Operations The purpose of this technical standard is to clarify DOE/NNSA expectations and to provide guidance for preparing HARs for NEOs. The general requirements for operation-specific HARs are those contained in Chapters 2-5 of DOE-STD-3009-94, Change Notice 2, “Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Documented Safety Analysis”, or superseding directives. |
05/19/2006 |
DOE-NE-STD-1004-92 |
Root Cause Analysis Guidance Document This document is a guide for root cause analysis specified by DOE Order 5000.3A, "Occurrence Reporting and Processing of Operations Information." Causal factors identify program control deficiencies and guide early corrective actions. As such, root cause analysis is central to DOE Order 5000.3A. |
07/27/2005 |
DOE-O-1300.2A |
DOE Technical Standards Program The principle function of this Order is to establish a DOE-wide technical standards program. |
09/04/1996 |
DOE-SPEC-3018-96 |
DOE Specification, Flooded-Type Lead-Acid Storage Batteries This specification defines requirements for flooded-type, lead-acid storage batteries and accessory equipment for [general purpose] [uninterruptible power supply (UPS)] [ ] applications, for [ ], located in [ ] |
09/12/1996 |
DOE-SPEC-3019-96 |
DOE Specification, Valve-Regulated Type Lead-Acid Storage Batteries This specification defines requirements for sealed valve-regulated type, lead-acid storage batteries and accessory equipment for [general purpose] [uninterruptible power supply (UPS)] |
09/17/1996 |
DOE-STD-0100T-93 |
Licensed Reactor Nuclear Safety Criteria Applicable to DOE Reactors This document identifies nuclear safety criteria applied to licensed reactors. The degree of application of these criteria to a DOE-owned reactor, consistent with their application to comparable licensed reactors, must be determined by the DOE and DOE contractor. |
07/12/1996 |
DOE-STD-101-92 |
Compilation of Nuclear Safety Criteria for Potential Application to DOE Nonreactor Nuclear Facilities This guide is a compilation and source list of nuclear safety criteria primarily used by the Nuclear Regulatory Commission (NRC) and private industry in commercial NNFs. Because the DOE , in some areas of NNF design, construction, operation, and decommissioning has taken the lead in developing NNF criteria, the guide also includes criteria used by the DOE and DOE contractors. |
06/24/1996 |
DOE-STD-1012-92 |
Guide to Good Practices for On-The-Job Training Training programs at DOE facilities should prepare personnel to safely and efficiently operate and maintain the facilities in accordance with DOE requirements. This guide presents good practices for performance-based on-the-job training and OJT programs. |
09/18/1996 |
DOE-STD-1020-2002 |
Natural Phenomena Hazards Design and Evaluation Criteria for Department of Energy Facilities It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards on DOE facilities. |
01/29/2002 |
DOE-STD-1020-2012 |
Natural Phenomena Hazards Analysis and Design Criteria for Department of Energy Facilities This Department of Energy (DOE) Standard (STD)-1020-2012, Natural Phenomena Hazards Analysis and Design Criteria for DOE Facilities, provides criteria and guidance for the analysis and design of facility structures, systems, and components (SSCs) that are necessary to implement the requirements of DOE Order (O) 420.1C, Facility Safety, and to ensure that the SSCs will be able to effectively perform their intended safety functions under the effects of natural phenomena hazards (NPHs). |
10/03/2012 |
DOE-STD-1021-93 |
Natural Phenomena Hazards Performance Categorization Guidelines for Structures, Systems, and Components The purpose of this standard is as follows: (a) To provide, for the purpose of Natural Phenomena Hazard (NPH) design and evaluation, criteria for selecting performance categories (PCs) of structures, systems, and components (SSCs) in accordance with the requirements specified in DOE Order 420.1 (Reference 10) and the NPH Guide to DOE O 420.1 (DOE G 420.1-2) (Reference 11). |
04/08/2002 |
DOE-STD-1022-94 |
Natural Phenomena Hazards Characterization Criteria The Department of Energy (DOE) has established policy and requirements for natural phenomena hazard (NPH) mitigation for DOE sites and facilities using a graded approach as specified by DOE O 420.1, “Facility Safety” and associated NPH Guide G 420.1-2. |
04/05/2002 |
DOE-STD-1023-95 |
Natural Phenomena Hazards Assessment Criteri It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPHs) on DOE facilities.It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities. |
04/08/2002 |
DOE-STD-1024-92 |
Guidelines for Use of Probabilistic Seismic Hazard Curves at Department of Energy Sites for Department of Energy Facilities The issue of the seismic hazard to be used in safety or risk assessments has recently been raised at a number of Department of Energy (DOE) facilities. One of the technical issues associated with this topic is the existence and use of two different methodologies for the development of seismic hazard curves by Lawrence Livermore National Laboratory (LLNL) and the Electric Power Research Institute (EPRI). |
03/22/1996 |
DOE-STD-1026-2009 |
NNSA Package Certification Engineer Functional Area Qualification Standard The NNSA Package Certification Engineer FAQS establishes common functional area competency requirements for all DOE package certification engineers who provide assistance, or direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
02/18/2009 |
DOE-STD-1029-92 |
Writer's Guide for Technical Procedures This Writer's Guide for Technical Procedures is one of a series of documents currently being developed by the U.S. Department of Energy (DOE) to define broad requirements for procedure program management and to provide guidance for the preparation of procedures used at DOE facilities. |
01/07/1999 |
DOE-STD-1050-93 |
Guideline to Good Practices for Planning, Scheduling, and Coordination of Maintenance at DOE Nuclear Facilities This guide is intended to assist facility maintenance operations in the review of existing and in developing new programs to ensure maintenance work package planning, scheduling, and coordination identifies all technical and administrative requirements for a work activity and provides the materials, tools, and support activities needed to perform the work. |
06/07/1996 |
DOE-STD-1051-93 |
Guideline to Good Practices for Maintenance Organization and Administration at DOE Nuclear Facilities This guide is intended to assist facility maintenance operations in the review of existing and in developing new organizational and administrative functions. |
09/07/1995 |
DOE-STD-1053-93 |
Guideline to Good Practices for Control of Maintenance Activities at DOE Nuclear Facilities This guide is intended to assist facility maintenance operations in the review of existing and in developing new programs to ensure maintenance practices provide an administrativemethod by which maintenance activities are identified, initiated, planned, approved, scheduled, coordinated, performed, and reviewed for adequacy and completeness. |
06/06/1996 |
DOE-STD-1054-93 |
Guideline to Good Practices for Control and Calibration of Measuring and Test Equipment This guide is intended to assist facility maintenance operations in the review of existing and in developing new programs to ensure the accuracy and integrity of performance data derived from Plant process and control instrumentation is verified by controlled application of properly calibrated/certified measuring and test equipment (M&TE) having the appropriate precision, design accuracy, and durability for their intended use. |
09/07/1995 |
DOE-STD-1055-93 |
Guideline to Good Practices for Maintenance Management Involvement at DOE Nuclear Facilities; This guide is intended to assist facility maintenance management in the review of existing and in developing new maintenance management programs. |
09/11/1995 |
DOE-STD-1058-93 |
Guide to Good Practices for Developing and Conducting Case Studies This guide contains a method for learning fromexperience to prevent mistakes fromoccurring. That method is the case study. This guide describes how to develop and present case studies. |
09/11/1995 |
DOE-STD-1061-93 |
Guide to Good Practices for the Selection, Training, and Qualification of Shift Supervisors This guide, used in conjunction with a facility-specific job analysis, provides a framework for the selection, training, qualification, and professional development of reactor facility and non-reactor nuclear facility shift supervisors. |
09/14/1995 |
DOE-STD-1063-2000 |
Establishing and Maintaining a Facility Representative Program at DOE Facilities This standard, Facility Representatives, DOE-STD-1063-2000, defines the duties, responsibilities and qualifications for DOE Facility Representatives, based on facility hazard classification; risks to workers, the public, and the environment; and the operational activity level |
03/31/2000 |
DOE-STD-1063-2006 |
Facility Representatives The purpose of the DOE Facility Representative Program is to ensure that competent DOE staff personnel are assigned to oversee the day-to-day contractor operations at DOE’s hazardous nuclear and non-nuclear facilities. |
04/06/2006 |
DOE-STD-1063-2011 |
Facility Representatives This standard, DOE-STD-1063, Facility Representatives, defines the duties, responsibilities and qualifications for Department of Energy (DOE) |
03/01/2011 |
DOE-STD-1063-97 |
Establishing and Maintaining a Facility Representative Program at DOE Facilities This standard, ""ESTABLISHING AND MAINTAINING A FACILITY REPRESENTATIVE PROGRAM AT DOE FACILITIES,” DOE-STD-1063-97, defines the duties, responsibilities and qualifications for DOE Facility Representatives, based on facility hazard classification; risks to workers, the public, and the environment; and the operational activity level. |
10/01/1997 |
DOE-STD-1064-94 |
Guideline to Good Practices for Seasonal Facility Preservation at DOE Nuclear Facilities This guide is intended to assist facility maintenance organizations in the review of existing methods and in the development of new methods for establishing a maintenance Seasonal Facility Preservation program. |
06/06/1996 |
DOE-STD-1065-94 |
Guideline to Good Practices for Postmaintenance Testing at DOE Nuclear Facilities This guide is intended to assist facility maintenance operations in the review of existing and in developing new PMT guidelines to be performed following maintenance, which proves that the structures, systems or components (SSC) are operable as designed. |
06/13/1996 |
DOE-STD-1066-2012 |
Fire Protection This Standard was developed to provide acceptable methods and approaches for meeting DOE fire protection program and design requirements and to address special or unique fire protection issues at DOE facilities that are not comprehensively or adequately addressed in national consensus standards or other design criteria. |
12/05/2012 |
DOE-STD-1066-97 |
Fire Protection Design Criteria This Standard provides supplemental fire protection guidance applicable to the design and construction of DOE facilities and site features (such as water distribution systems) that are also provided for fire protection. It is intended to be used in conjunction with the applicable building code, National Fire Protection Association (NFPA) Codes and Standards, and any other applicable DOE construction criteria. |
03/26/1997 |
DOE-STD-1066-99 |
Fire Protection Design Criteria This Standard provides supplemental fire protection guidance applicable to the design and construction of DOE facilities and site features (such as water distribution systems) that are also provided for fire protection. It is intended to be used in conjunction with the applicable building code, National Fire Protection Association (NFPA) Codes and Standards, and any other applicable DOE construction criteria |
07/09/1999 |
DOE-STD-1067-94 |
Guide to Good Practices for Maintenance Facilities, Equipment, and Tools at DOE Nuclear Facilities This guide is intended to assist facility maintenance management in defining the development, documentation, and implementation of the maintenance history program. It is expected that each DOE facility may use different approaches or methods than those defined in this guide. |
05/21/1996 |
DOE-STD-1068-94 |
Guide to Good Practices for Maintenance History at DOE Nuclear Facilities This guide is intended to assist facility maintenance management in defining the development, documentation, and implementation of the maintenance history program. |
05/09/1996 |
DOE-STD-1069-94 |
Guideline to Good Practices for Maintenance Tools and Equipment Control at DOE Nuclear Facilities This guide is intended to assist facility maintenance organizations in the review of existing methods and in developing new methods for establishing maintenance tool and equipment control for all areas of the facility, including radiologically controlled areas (RCAs). |
06/06/1996 |
DOE-STD-1070-94 |
Guidelines For Evaluation of Nuclear Facility Training Programs The Guidelines for Evaluation of Nuclear Facility Training Programs establish objectives and criteria for evaluating nuclear facility training programs. The guidance in this standard provides a framework for the systematic evaluation of training programs at nuclear facilities and is based, in part, on established criteria for Technical Safety Appraisals, Tiger Team Assessments, commercial nuclear industry evaluations, and the DOE Training Accreditation Program. |
11/22/1995 |
DOE-STD-1070-94 |
Guidelines For Evaluation of Nuclear Facility Training Programs This standard initiates a framework for consistent, systematic evaluation of DOE nuclear facility training programs through the establishment and use of a uniform set of training program evaluation objectives and criteria. The performance objectives and criteria contained in the Appendix to this standard shall be used by DOE Headquarters and field organizations for the evaluation of nuclear facility training and qualification programs. |
06/10/2013 |
DOE-STD-1071-94 |
Guideline to Good Practices for Material Receipt, Inspection, Handling, Storage, Retrieval, and Issuance at DOE Nuclear Facilities This guide is intended to assist facility maintenance organizations in the review of existing methods and in the development of new methods for establishing a material receipt, inspection, handling, storage, retrieval, and issuance process/system which ensures timely delivery of the proper parts and materials, in the condition required for effectivemaintenance activities, and periodic services which provide unique and/or supplemental maintenance support. |
05/30/1996 |
DOE-STD-1072-94 |
Guideline to Good Practices for Facility Condition Inspections at DOE Nuclear Facilities This guide is intended to provide a means for owner/operators to have an awareness of the way business is actually being conducted on the shop floor. Also, this guide is intended to provide a means for maintenance managers to impart their expectations to craftspersons as to how maintenance should be conducted. |
06/07/1996 |
DOE-STD-1073-2003 |
Configuration Management Program The purpose of this standard is to define the objectives of a configuration management process for DOE nuclear facilities (including activities and operations), and to provide detailed examples and supplementary guidance on methods of achieving those objectives. Configuration management is a disciplined process that involves both management and technical direction to establish and document the design requirements nd the physical configuration of the nuclear facility and to ensure that they remain consistent with each other and the documentation. |
10/27/2003 |
DOE-STD-1073-93 |
Guide for Operational Configuration Management Program Part II This Standard presents the program criteria and implementation guidance for an operational configuration management (CM) program for Department of Energy (DOE) facilities. This Standard is applicable to DOE nuclear facilities in the operational phase. |
01/18/1996 |
DOE-STD-1075-94 |
Standard For Developing and Issuing DOE Safety Guides and Implementation Guides This standard establishes the style, format, content, and process for the preparing and issuing Department of Energy (DOE) guides. This standard is intended for use by all DOE components (including their contractors) when preparing, revising, commenting on, or issuing DOE guides. |
11/22/1995 |
DOE-STD-1077-94 |
Training Accreditation Program Standard: Requirements and Guidelines The purpose of this Standard is to provide requirements, information, and guidance for the effective implementation of the DOE Training Accreditation Program established by DOE Order 5480.18B, “Nuclear Facility Training Accreditation Program.” |
06/13/1996 |
DOE-STD-1082-94 |
Preparation, Review, and Approval of Implementation Plans for Nuclear Safety Requirements This standard describes an acceptable method to prepare, review, and approve implementation plans for DOE nuclear safety requirements. DOE requirements are identified in DOE Rules, Orders, Notices, Immediate Action Directives, and Manuals (hereinafter referred to as DOE requirements documents). |
11/29/1995 |
DOE-STD-1083-2009 |
Processing Exemptions to Nuclear Safety Rules and Approval of Alternative Methods for Documented Safety Analyses DOE may grant temporary or permanent exemptions from its nuclear safety requirements in rules provided that the provisions of 10 C.F.R. Part 820, Subpart E, ""Exemption Relief,"" are met. The provisions of 10 C.F.R. Part 820 state that the Secretarial Officer (defined in 10 C.F.R. Part 820) shall utilize any procedures deemed necessary and appropriate to comply with the exemption responsibilities. This Standard establishes acceptable procedures that may be used to request and grant exemptions to DOE nuclear safety rules in accordance with 10 C.F.R. Part 820. |
06/29/2009 |
DOE-STD-1083-95 |
Requesting and Granting Exemptions to Nuclear Safety Rules DOE may grant temporary or permanent exemptions to its nuclear safety rules provided that the provisions of 10 CFR Part 820, Subpart E, ""Exemption Relief,"" are met. The provisions of 10 CFR Part 820 state that the Secretarial Officer (as described in Section 3.5, below) shall utilize any procedures deemed necessary and appropriate to comply with the exemption responsibilities. |
12/04/1995 |
DOE-STD-1088-95 |
Fire Protection for Relocatable Structures This Standard provides fire protection criteria applicable to the design, construction, and location of relocatable structures as defined herein. It also addresses fire extinguishing methods and general safeguards. |
08/18/1995 |
DOE-STD-1090-2004 |
Hoisting and Rigging Standard The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended as a reference document to be used by supervisors, line managers, safety personnel, equipment operators, and any other personnel responsible for safety of hoisting and rigging operations at DOE sites. The standard quotes verbatim or paraphrases (with minor editorial changes for consistency) the requirements of the U.S. Occupational Safety and Health Administration (OSHA) and the American National Standards Institute (ANSI). |
06/01/2004 |
DOE-STD-1090-2007 |
Hoisting and Rigging Standard The reissued June 1995 edition marked a change in classification. The DOE Office of Scientific and Technical Information (OSTI) reclassified the manual as a handbook and it was issued as DOE Hoisting and Rigging Handbook (DOE-HDBK-1090-95). After further review, OSTI has reclassified the handbook as a DOE Technical Standard and the September 1996 edition was issued as DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) DOE-STD-1090-96 (Rev-1). Additional revisions issued are DOE-STD-1090-99, DOE-STD-1090-2001, DOE-STD-1090- 2004, and DOE-STD-1090-2007. |
08/29/2007 |
DOE-STD-1095-95 |
Department of Energy Laboratory Accreditation Program for Personnel Dosimetry Systems This standard establishes the method for obtaining accreditation of personnel dosimetry systems by the Department of Energy Laboratory Accreditation Program. |
08/09/2005 |
DOE-STD-1098-2008 |
Radiological Control The Department of Energy (DOE) has developed this Standard to assist line managers in meeting their responsibilities for implementing occupational radiological control programs. |
11/19/2008 |
DOE-STD-1098-99 |
Radiological Control It is the policy of DOE to conduct its radiological operations in a manner that ensures the health and safety of all its employees, contractors, and the general public. In achieving this objective, the Department shall ensure that radiation exposures to its workers and the public and releases of radioactivity to the environment are maintained below regulatory limits and deliberate efforts are taken to further reduce exposures and releases as low as reasonably achievable. The Department is fully committed to implementing a radiological control program of the highest quality that consistently reflects this policy. |
01/26/2005 |
DOE-STD-1104-2009 |
Review and Approval of Nuclear Facility Safety Basis and Safety Design Basis Documents This Standard describes a framework and criteria for reviewing safety basis documents that will support DOE approval of the documents as required by 10 CFR 830 Subpart B and DOE-STD-1189-2008 (as invoked by DOE Order 413.3A, Chg 1) including preparation of SERs and SVRs for nuclear facilities. |
05/07/2009 |
DOE-STD-1104-2014 |
Review and Approval of Nuclear Facility Safety Basis and Safety Design Basis Documents. This Standard describes a framework and the criteria to be used for approval of (1) safety basis documents, as required by 10 Code of Federal Regulation (C.F.R.) 830, Nuclear Safety Management, and (2) safety design basis documents, as required by Department of Energy (DOE) Standard (STD)-1189-2008, Integration of Safety into the Design Process. |
12/19/2014 |
DOE-STD-1104-96 |
Review and Approval of Nuclear Facility Safety Basis Documents (Documented Safety Analysis and Technical Safety Requirements) First of many: The following guiding principles pertain to the application and provisions of this Standard. · The documents (i.e., DOE orders, manuals, guides, and standards) listed in Table 2 of Appendix A to 10 CFR 830 Subpart B provide approved methodologies for meeting the DSA requirements of 10 CFR 830. Developed consistent with and as a companion to these documents, this standard does not reiterate the provisions of these documents. |
02/21/2006 |
DOE-STD-1107-97 |
Knowledge, Skills, and Abilities for Key Radiation Protection Positions at DOE Facilities This document provides detailed qualification criteria for contractor key radiation protection personnel. Although federal key radiation protection positions are also identified in Table 1, qualification standards for federal positions are provided in DOE O 360.1 and the DOE Technical Qualifications Program. |
06/01/2005 |
DOE-STD-1111-98 |
Laboratory Accreditation Program Administration The purpose of this technical standard is to establish procedures for administering DOELAP and acquiring accreditation. Specific performance testing requirements and site assessment criteria for accreditation are contained in: DOE-STD-1095-95, “Department of Energy Laboratory Accreditation Program for Personnel Dosimetry Systems” and DOE-STD-1112-98, “Department of Energy Laboratory Accreditation for Radiobioassay.” |
03/04/1999 |
DOE-STD-1112-98 |
Laboratory Accreditation Program for Radiobioassay This technical standard describes the U.S. Department of Energy Laboratory Accreditation Program (DOELAP) for Radiobioassay, for use by the U.S. Department of Energy (DOE) and DOE Contractor radiobioassay programs. |
03/22/1999 |
DOE-STD-1120-2005 |
Integration of Environment, Safety, and Health into Facility Disposition Activities Subsequent to the initial release of DOE-STD-1120-98, nuclear safety basis requirements were promulgated in 10 CFR 830, Subpart B. The standard was identified as a “safe harbor” approach for preparing a documented safety analysis (DSA) for decommissioning and environmental restoration activities. The May 1998 version of the standard was not explicit regarding compliance with safety basis requirements of Part 830 |
04/13/2005 |
DOE-STD-1121-2008 |
Internal Dosimetry Internal dosimetry is “...the scientific methodology used to measure, calculate, estimate, assay, predict, and otherwise quantify the radiative energy absorbed by the ionization and excitation of atoms in human tissues as a result of the emission of energetic radiation by internally deposited radionuclides” (Raabe 1994). |
10/17/2008 |
DOE-STD-1128-2008 |
Guide of Good Practices for Occupational Radiological Protection in Plutonium Facilities This Technical Standard (TS) does not contain any new requirements. Its purpose is to provide a guide to good practice, update existing reference material, and discuss practical lessons learned relevant to the safe handling of plutonium. |
01/05/2009 |
DOE-STD-1128-98 |
Guide of Good Practices for Occupational Radiological Protection in Plutonium Facilities This Technical Standard (TS) does not contain any new requirements. Its purpose is to provide guides to good practice, update existing reference material, and discuss practical lessons learned relevant to the safe handling of plutonium. |
05/07/2003 |
DOE-STD-1128-98 |
Guide of Good Practices for Occupational Radiological Protection in Plutonium Facilities This Technical Standard (TS) does not contain any new requirements. Its purpose is to provide guides to good practice, update existing reference material, and discuss practical lessons learned relevant to the safe handling of plutonium. |
01/11/2007 |
DOE-STD-1134-99 |
Review Guide For Criticality Safety Evaluations The purpose of this document is to provide a set of guidelines, not checklists, for use by DOE criticality safety personnel when reviewing criticality safety evaluations produced by the contractor. This review guide is intended to provide a consistent framework for assuring that acceptable evaluations are produced by DOE contractors. |
09/27/1999 |
DOE-STD-1135-99 |
Guidance for Nuclear Criticality Safety Engineer Training and Qualification The information contained in this Standard describes the requirements for Training and Qualification of Contractor NCS Engineers in the U. S. Department of Energy (DOE) complex to facilitate hiring and maintaining of trained and qualified NCS staff. |
09/27/1999 |
DOE-STD-1136-2000 |
Guide of Good Practices for Occupational Radiological Protection in Uranium Facilities This Technical Standard (TS) provides operational guidance, practical lessons learned and experience gained, guides to good practice, and reference information on the safe handling of uranium. The TS provides information to assist uranium facilities in complying with Title 10 of the Code of Federal Regulations (CFR), Part 835, Occupational Radiation Protection (10 CFR 835) (DOE 1998a). This TS supplements the DOE G 441.1 series of Guides, DOE Orders, and DOE-STD-1098-99, Radiological Control (RCS) (DOE 1999a) and has as its sole purpose the protection of workers and the public from the hazards that are inherent in uranium storage, processing, and handling. |
12/19/2001 |
DOE-STD-1136-2004 |
Guide of Good Practices for Occupational Radiological Protection in Uranium Facilities This Technical Standard (TS) provides operational guidance, practical lessons learned and experience gained, guides to good practice, and reference information on the safe handling of uranium. The TS provides information to assist uranium facilities in complying with Title 10 of the Code of Federal Regulations (CFR), Part 835, Occupational Radiation Protection (10 CFR 835) (DOE 1998a). |
01/11/2005 |
DOE-STD-1137-2000 |
Fire Protection Engineering Functional Area Qualification Standard The Fire Protection Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy federal fire protection engineers who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
07/25/2000 |
DOE-STD-1137-2007 |
Fire Protection Engineering Functional Area Qualification Standard Fire protection engineers use science and technology to evaluate the effects of fires to protect workers, public, people, environment, and property. They analyze how facilities are used, how fires start and grow, and how fire and smoke affect people, buildings and property. Fire protection engineers evaluate many facets of the fire protection field. |
12/05/2007 |
DOE-STD-1138-2000 |
Industrial Hygiene Functional Area Qualification Standard The Industrial Hygiene Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy industrial hygiene personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities having an impact on the safe operation of defense nuclear facilities. |
07/25/2000 |
DOE-STD-1146-2001 |
General Technical Base Qualification Standard The General Technical Base Qualification Standard establishes common technical competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
11/07/2001 |
DOE-STD-1146-2007 |
General Technical Base Qualification Standard The General Technical Base Qualification Standard establishes common technical competency requirements for all DOE personnel who provide assistance in, direction or guidance to, or oversight or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
12/05/2007 |
DOE-STD-1149-2002 |
Safety and Health Program for DOE Construction Projects The intent of this standard is to provide an effective methodology for managing the hazards inherent to construction work in a systematic manner that can be easily integrated with the management of other technical aspects of a construction project. |
03/01/2002 |
DOE-STD-1151-2002 |
Facility Representative Functional Area Qualification Standard The Facility Representative Functional Area Qualification Standard has been developed as a tool to assist DOE Program and Field offices in the development and implementation of the Technical Qualification Program in their organization. |
05/08/2002 |
DOE-STD-1156-2002 |
Environmental Compliance Functional Area Qualification Standard The Environmental Compliance Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of DOE’s most hazardous facilities. |
02/05/2003 |
DOE-STD-1158-2002 |
Self-Assessment Standard for DOE Contractor Criticality Safety Programs This document encompasses all elements of the Contractor criticality safety program at DOE facilities. The effectiveness of the criticality safety program is dependent upon management implementing its roles and responsibilities to integrate criticality safety into work practices. This doc is an assessment tool. |
12/06/2002 |
DOE-STD-1160-2003 |
Occupational Safety Functional Area Qualification Standard The Occupational Safety Functional Area Qualification Standard is not intended to replace the OPM Qualification Standards or other DOE personnel standards, rules, plans, or processes. The primary purpose of the Technical Qualification Program is to ensure that employees have the requisite technical competency to support the DOE mission. |
03/11/2003 |
DOE-STD-1161-2003 |
Mechanical Systems Functional Area Qualification Standard The Mechanical Systems Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy mechanical systems personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
06/16/2003 |
DOE-STD-1162-2003 |
Instrumentation and Control Functional Area Qualification Standard The Instrumentation and Control Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy Instrumentation and Control personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
06/17/2003 |
DOE-STD-1164-2003 |
Aviation Safety Officer, Functional Area Qualification Standard The Aviation Safety Officer Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy aviation safety personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of DOE facilities. |
09/26/2003 |
DOE-STD-1165-2003 |
Aviation Manager Functional Area Qualification Standard The Aviation Manager Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy aviation managers who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe, effective, secure and efficient operation of DOE facilities. |
09/25/2003 |
DOE-STD-1170-2003 |
Electrical Systems Functional Area Qualification Standard The Electrical Systems Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
12/18/2003 |
DOE-STD-1171-2003 |
Safeguard and Security Functional Area Standard The Safeguards and Security (S&S) Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
12/18/2003 |
DOE-STD-1172-2003 |
Safety Software Quality Assurance Functional Area Qualification Standard The Safety Software Quality Assurance Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of safety software that includes, but is not limited to safety software used for consequence analysis for potential accidents and design basis events, design for structures, systems and components, instrumentation and controls (I&C), and also other types of software, such as databases used for safety management functions. |
12/19/2003 |
DOE-STD-1173-2003 |
Criticality Safety Functional Areq Qualification Standard The Criticality Safety Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy criticality safety personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
12/11/2003 |
DOE-STD-1175-2003 |
DOE-STD-1175-2003: Senior Technical Safety Manager Functional Area Qualification Standard A Senior Technical Safety Manager (STSM) is that person who is usually at the GS/GM-15 or Senior Executive Service level and assigned the direct responsibility to manage technical programs, resources, and/or Department personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
12/22/2003 |
DOE-STD-1176-2004 |
Chemical Processing Functional Area Qualification Standard The Chemical Processing Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy chemical processing personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities impacting the safe operation of defense nuclear facilities. |
01/16/2004 |
DOE-STD-1181-2004 |
Facility Maintenance Management Functional Area Qualification Standard The Facility Maintenance Management Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
03/25/2004 |
DOE-STD-1182-2004 |
Civil/Structural Engineering Functional Area Qualification Standard Replaced by DOE-STD-1182-2014 The Civil/Structural Engineering Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
03/25/2004 |
DOE-STD-1183-2004 |
Nuclear Safety Specialist Functional Area Qualification Standard The Nuclear Safety Specialist Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
04/27/2004 |
DOE-STD-1183-2007 |
Nuclear Safety Specialist Functional Area Qualification Standard The Nuclear Safety Specialist FAQS establishes common functional area competency requirements for all DOE nuclear safety specialist personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
11/15/2007 |
DOE-STD-1185-2004 |
Nuclear Explosive Safety Study Functional Area Qualification Standard The Nuclear Explosive Safety Study Functional Area Qualification Standard establishes common functional area competency requirements for Department of Energy personnel who provide assistance, direction, guidance, oversight, or evaluation of contractor technical activities that could impact the safe operation of DOE’s defense nuclear facilities. |
08/19/2004 |
DOE-STD-1185-2007 |
Nuclear Explosive Safety Study Functional Area Qualification Standard The technical FAQS has been developed as a tool to assist DOE program and field offices in the development and implementation of the TQP in their organization. For ease of transportability of qualifications between DOE elements, program and field offices are expected to use this technical FAQS without modification. |
09/25/2007 |
DOE-STD-1186-2004 |
Specific Administrative Controls This Standard provides guidance applicable to that are selected to provide preventive and/or mitigative functions for specific potential accident scenarios, and which, also have safety importance equivalent to engineered controls that would be classified as Safety Class (SC) or Safety Significant (SS) if the engineered controls were available and selected. This class of AC is designated as Specific Administrative Controls (SAC). |
03/31/2004 |
DOE-STD-1189-2008 |
Integration of Safety into The Design Process The Standard provides guidance on a process of integration of Safety-in-Design intended to implement the applicable ISM core functions—define the work, analyze the hazards, establish the controls—necessary to provide protection of the public, workers, and the environment from harmful effects of radiation and other such toxic and hazardous aspects attendant to the work. |
03/31/2008 |
DOE-STD-1194-2011 |
Nuclear Materials Control and Accountability This document describes establishing and maintaining a Material Control and Accountability (MC&A) program, where each MC&A program element is a part of a quality MC&A program. Each site/facility operator needs to establish a sustainable, effective graded safeguards program for the control and accounting of nuclear materials to detect and deter theft and diversion, and to prevent the unauthorized control of a weapon, test device, or materials that can be used to make an improvised nuclear device. |
12/18/2012 |
DOE-STD-1207-2012 |
Protection Programming Defensive Planning for Fixed Facilities This document provides Department of Energy (DOE) field offices and associated facilities/sites with a standard methodology for adapting the Department’s tactical doctrine to site-specific needs in a coherent, consistent, and repeatable fashion. |
01/09/2013 |
DOE-STD-3003-2000 |
Backup Power Sources For DOE Facilities The purpose of this Standard is to document good engineering practices for the installation, testing, and maintenance of BACKUP POWER SOURCES at DOE facilities. The term "BACKUP POWER SOURCES" as used in this Standard covers both "emergency" and "backup" power applications. |
01/27/2000 |
DOE-STD-3006-2000 |
Planning and Conduct of Operational Readiness Reviews DOE O 425.1B specifies the conditions and circumstances when an Operational Readiness Review (ORR) or a Readiness Assessment (RA) is required as part of a new start or restart process. This standard provides guidance on the planning and conduct of the ORRs and RAs |
07/14/2000 |
DOE-STD-3006-95 |
Planning and Conduct of Operation Readiness Reviews DOE 0 425.1 specifies the conditions and circumstances when an Operational Readiness Review (ORR) or a Readiness Assessment (RA) is required as part of a new start or restart process. This standard provides guidance on the planning and conduct of the Operational Readiness Reviews. This standard also provides guidance for requesting exemptions. The requirements for ORRs and RAs apply both to responsible contractors and to DOE. This standard addresses the requirements and suggests methods and approaches for both. |
12/05/1995 |
DOE-STD-3007-93 |
Guidelines for Preparing Criticality Safety Evaluations at Department of Energy Non-Reactor Nuclear Facilities Contained in this document are guidelines that should be followed when preparing Criticality Safety Evaluations that will be used to demonstrate the safety of operations performed at Department of Energy (DOE) Non-Reactor Nuclear Facilities. |
09/17/1998 |
DOE-STD-3009-94 |
Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses This Standard describes a DSA preparation method that is acceptable to the DOE as delineated for those specific facilities listed in Table 2 of Appendix A, “General Statement of Safety Basis Policy”, to Subpart B, “Safety Basis Requirements”, of 10 CFR 830. It was developed to assist Hazard Category 2 and 3 facilities in preparing SARs that will satisfy the requirements of 10 CFR 830. |
03/24/2006 |
DOE-STD-3009-94 |
Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Documented Safety Analysis This Standard describes a DSA preparation method that is acceptable to the DOE as delineated for those specific facilities listed in Table 2 of Appendix A, “General Statement of Safety Basis Policy”, to Subpart B, “Safety Basis Requirements”, of 10 CFR 830. It was developed to assist Hazard Category 2 and 3 facilities. in preparing SARs that will satisfy the requirements of 10 CFR 830. |
05/30/2005 |
DOE-STD-3011-2002 |
Guidance for Preparation of Basis for Interim Operation (BIO) Documents Superseding DOE-STD-3011-94 (November 1994) This Standard provides a Department of Energy (DOE) approved methodology for preparing a Basis for Interim Operation (BIO) document. |
01/03/2003 |
DOE-STD-3013-2000 |
Stabilization, Packaging, and Storage of Plutonium-Bearing Materials This Standard provides criteria for stabilization of plutonium-bearing materials at DOE facilities to safe and stable forms that can be packaged and placed in storage with minimal surveillance for up to 50 years. This Standard applies to plutonium-bearing metals and oxides containing at least 30 wt% plutonium plus uranium. |
08/07/2001 |
DOE-STD-3013-2004 |
Stabilization, Packaging, and Storage of Plutonium-Bearing Materials This Standard provides criteria for stabilization of plutonium-bearing materials at DOE facilities to safe and stable forms that can be packaged and placed in storage with minimal surveillance for up to 50 years. This Standard applies to plutonium-bearing metals and oxides containing at least 30 wt% plutonium plus uranium. |
07/16/2004 |
DOE-STD-3015-2001 |
Nuclear Explosive Safety Study Process This technical standard provides specific requirements and guidance for nuclear explosive safety (NES) studies and is in accordance with DOE Order 452.2B, SAFETY OF NUCLEAR EXPLOSIVE OPERATIONS |
02/28/2001 |
DOE-STD-3015-2004 |
Nuclear Explosive Safety Evaluation Process This technical standard provides specific information regarding nuclear explosive safety studies (NESSs), operational safety reviews (OSRs), and nuclear explosive safety change evaluations (NCEs) and is in accordance with DOE O 452.2, Safety of Nuclear Explosive Operations. |
11/04/2004 |
DOE-STD-3020-2005 |
Specification for HEPA Filters used by DOE Contractors This standard establishes specifications and quality assurance requirements for High Efficiency Particulate Air (HEPA) filters procured to protect workers, the public, and the environment when installed in DOE nuclear facilities |
12/12/2005 |
DOE-STD-3020-97 |
Specification for HEPA Filters used by DOE Contractors This standard establishes specification and testing requirements for High Efficiency Particulate Air (HEPA) filters procured to provide personnel and environmental protection when installed in DOE nuclear facilities. The standard specifies minimum requirements to be included in contractor specifications. |
03/12/1997 |
DOE-STD-3022-98 |
DOE HEPA Filter Test Program This standard establishes essential elements of a Department of Energy (DOE) program for testing HEPA filters to be installed in DOE nuclear facilities or used in DOEcontracted activities. A key element is the testing of HEPA filters for performance at a DOE Filter Test Facility (FTF) prior to installation. |
05/19/1998 |
DOE-STD-3024-98 |
Content of System Design Descriptions This section provides background information concerning the purpose and functions of System Design Descriptions (SDDs) and the use of this standard in preparing SDDs. This section has been formatted differently from the main body of this standard, which starts on page 1 with the outline for an SDD. |
08/11/2005 |
DOE-STD-3025-99 |
Quality Assurance Inspection and Testing of HEPA Filters This standard establishes essential elements for the quality assurance inspection and testing of HEPA filters by U.S. Department of Energy (DOE)-accepted Filter Test Facilities (FTF). |
03/01/1998 |
DOE-STD-3026-99 |
Filter Test Facility Quality Program Plan This standard was developed primarily for application in U.S. Department of Energy programs. It contains specific direction for HEPA filter testing performed at a DOE-accepted HEPA Filter Test Facility (FTF). Beneficial comments (recommendations, additions, deletions) and any pertinent data that may improve this document should be sent to the Office of Nuclear Safety Policy and Standards (EH-31), U.S. Department of Energy, Washington, D.C. 20585, by letter or by using the self-addressed Document Improvement Proposal form (DOE F 1300.3) appearing at the end of this document. |
02/24/2009 |
DOE-STD-5503-94 |
EM Health and Safety Plan Guidelines These guidelines have been developed by a working group consisting of both field and headquarters personnel to provide new direction to the EM-40 program in the preparation of sitespecific Health and Safety Plans (HASPs). |
06/12/2006 |
DOE-STD-5503-94 |
EM Health and Safety Plan Guidelines These guidelines have been developed by a working group consisting of both field and headquarters personnel to provide new direction to the EM-40 program in the preparation of sitespecific Health and Safety Plans (HASPs). While based on the minimum requirements of 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response (HAZWOPER), and DOE orders, these guidelines have been developed with the express purpose of implementing a high quality safety and health program. |
06/12/1996 |
DOE-STD-6005-01 |
Industrial Hygiene Practices This standard recommends industrial hygiene practices to support components of the Worker Protection Program required by Department of Energy (DOE) Order 440.1A, Worker Protection Management for DOE Federal and Contractor Employees. |
04/30/2001 |
DOE-TSL-1-2002 |
Department of Energy Standards Index catalog or index of available DOE standards |
12/30/2002 |
DOE-TSL-2-2002 |
Directory of Points of Contact for the DOE Technical Standards Program This TSL supplements DOE manuals, directives, orders, and standards. It provides basic and fundamental information for DOE Component personnel involved in identifying standardization documents. It also provides listings of points of contact within DOE and identifies links to points of contact within the Department of Defense (DoD) for coordination of standardization activities. |
09/24/2002 |
DOE-TSL-4-99 |
Directory of DOE and Contractor Personnel Involved in Non-Government Standards Activities; Directory of DOE and Contractor Personnel Involved in Non-Government Standards Activities The body of this document contains a listing of DOE employees and DOE contractors who have submitted form DOE F 1300.2, Record of Non-Government Standards Activity, which is attached to the end of this document. |
05/21/1999 |