|
How to Insulate a Floor
Heat loss through an uninsulated floor over a vented crawl space can be
significant. Depending on the size of your home, you can save $50 or more
in heating costs each year by insulating your floor.
Do not insulate your floor if the crawl space is not well-vented (it should
have at least two vent openings to provide cross ventilation), or if the floor is over a heated space, such as a finished
basement.
Some General Specifications for Floor Insulation
If there is standing water underneath your house, adequate drainage should
be provided before under-floor insulation is installed. Consult your
utility to get information on how to provide drainage as required by the
Uniform Building Code. Moderate seasonal drainage problems won't
significantly affect the insulation, but you must provide good ventilation
in the crawl space. Check also for dry rot, termites or carpenter ants in
the floor joists or subflooring. These problems must be remedied by a
professional before you begin to install under-floor or perimeter
insulation.
To Insulate the Floor, You'll Need:
- Protective Gear: Wear a respirator, knee pads, cotton gloves, and a
hard hat. Loose fitting protective clothing and shoes with non-slip soles
are a good idea.
- Insulation and Materials
- Enough R-19 batt-type insulation with vapor barrier facing to cover the
subfloor area. You may use unfaced insulation only if a vapor barrier is
present or installed under the floor between the unfaced insulation and the
subflooring; or
- Enough loose-fill insulation to cover the under-floor area to R-19; or
- If you are using exterior perimeter insulation, enough R-10 foam board to
cover the foundation to the below-ground level required. Foam board used
for perimeter insulation should have a moisture absorption rate of 3
percent or less and a perm rating of 2 or less. Bead board (expanded
polystyrene) does not qualify. Your insulation dealer should be able to
give you the information you need. NOTE: Perimeter insulation is not
recommended except under very limited conditions.
- Several rolls of solid stainless steel or copper 18-gauge wire, sturdy
(150 pound breaking point) polypropylene twine, chicken wire, wood lath, or
preformed wire supports to hold the insulation between the joists.
- Six-mil black opaque polyethylene sheeting, or its equivalent, with a
"permeance" (see Glossary of Terms) of 0.5, large enough to cover
the crawl space floor and extend 6 inches up the foundation sidewalls. All
seams should be lapped 12 inches.
For Exterior Perimeter Insulation, You'll Also Need:
- Enough metal "Z flashing" to extend all the way around your
house between the foundation and the siding (Fig 4.1). "Flashing"
is a metal strip, ordered from any sheet metal shop, which extends from the
siding over the insulation to protect it from moisture.
- Cement board to cover the insulation as a fire retardant.
For Interior Perimeter Insulation, You'll Also Need:
- Enough 1 x 2 wood strips to extend along the entire perimeter of the foundation walls.
With Loose-Fill Insulation Installed Under The Floor, You'll Need:
- Enough fiberboard sheathing with a permeability of 10 perms or more to cover the under-floor area and hold the insulation in place.
Tools and Equipment:
- Hammer and hot-dipped galvanized roofing nails
- Duct tape
- Staple gun and rust-resistant steel divergent point of modified divergent point staples
- Mastic
Under-floor Insulation
Figure 4.2 a-e, shows where to insulate your floor for different types of
constructions. As shown in Fig. 4.2a, you should not insulate floors over
heated basements. Instead, insulate the basement walls by following the
instructions for Walls, Section VI.
Batt insulation can be installed over a crawl space by supporting it either
with wire or nylon twine laced between the floor joists or with wood lath
nailed or stapled into place. The insulation shall be installed so that it
is in contact with the subfloor.
Chicken wire is nailed or stapled onto the joist. Work with one
width at a time, nailing into place every 12 inches. (Fig. 4.3)
Nylon twine is stapled to joists every 12 inches and laced into a
"shoelace" pattern (Fig. 4.4).
Wire is attached with staples or nails every 12 inches and laced in
a zigzag pattern (Fig. 4.5).
Wire hangers specially formed to support under-floor insulation can
be stuck into the floor joists every 18 inches (Fig 4.6). The points on
each end of the hangers must penetrate the joists by at least ¾ inch.
Wood lath is nailed or stapled to the bottoms of beams or joists
every 12-18 inches (Fig. 4.7).
Loose fill insulation can be installed under floors using fiberboard
sheathing attached to the bottom of the joists every 6 inches with
stainless steel staples (Fig. 4.8). Insulation can then be blown in over
the sheathing.
Push the insulation into place over the supports (chicken wire, twine,
wire, or wood lath) with the vapor barrier facing away from you, against
the subfloor as shown in Figures 4.3 through 4.7. Do not compress the
insulation at any point, or you will lessen its insulating ability.
Fit batts securely against each other. Repeat the process until the entire
floor is insulated.
If you use fiberboard sheathing with loose fill insulation, you must first
staple a vapor barrier into place between the joists.
Staple the sheathing onto the bottom of the joists every 6 inches. Fit each
successive board closely up against the last one. (Fig. 4.9.)
Cut a small hole in the sheathing inside each joist space to blow in
insulation. (Fig. 4.10.) Divide bags up among the spaces for even
coverage. Tape the sheathing back over the hole when finished.
Insulate all water pipes not enclosed in the under-floor insulation to R 3,
or more if winter climate is severe in your area. Insulation of water pipes
is described in Section V, Insulating Pipes and Ducts.
If your crawl space has an access door opening into the home, it should be
insulated to the same R-value as the rest of the under-floor. Staple R-19
batts onto the crawl space side with the vapor barrier toward the house.
The access door should be weather-stripped with self-adhesive foam rubber.
Information on weather-stripping is included in Section VII.
To Finish Up:
Before leaving the crawl space, lay a sheet of polyethylene to cover the
entire crawl space floor. This serves to keep ground moisture from soaking
the insulation.
Clear the crawl space floor first of any debris which might puncture or
tear the ground cover. The ground cover is held in place with sand or
coarse gravel or bricks. Lap the seams 12 inches.
Extend the ground cover 6 inches up the foundation sidewalls. Use mastic to
affix wood lath to the foundation walls 6 inches up from the crawl space
floor. Staple the ground cover to the wood strips along the entire length
of the foundation. (Fig. 4.11.) Do
not cover any foundation vents.
Make sure you use enough plastic so that the ground cover fits snugly
against the foundation, avoiding the "bathtub" effect.
If aground cover is already installed, make sure it is in good condition.
Repair any tears with duct tape. Or, cover them with new plastic sheeting,
overlapping the intact part of the ground cover 12 inches and taping in
place with duct tape.
Perimeter Insulation
If your house is of "slab-on grade" construction or has a
"whole house plenum" heating system (see Glossary of Terms), or
if there isn't adequate space under the floor to insulate, you should
install exterior perimeter insulation in place of under-floor insulation.
Perimeter insulation is applied to the foundation walls.
Check with your utility first if you plan to use perimeter insulation. It
is more difficult to install than under-floor insulation, and can
contribute to unwanted moisture in the crawl space and indoor air pollution
in the living-space. Under-floor insulation is recommended wherever
possible.
Exterior perimeter insulation extends at least 12 inches below
ground level, so you must dig a trench in order to install it (Fig. 4.12).
Check with county building officials to find out the frost line in your
area, and dig a trench to that depth or to 2 feet, whichever is greater. If
your area does not have freezing conditions or if the frost line is higher
than 12 inches, the trench should be at least 12 inches deep. Do not dig
below the level of the foundation footings or you may damage or weaken
foundation footings.
Clean the foundation walls thoroughly. Projections such as pipes, cables,
etc., obstruct the application of outside perimeter insulation. You must
insulate around them or remove them before application.
Install the metal "Z" flashing which protects the foam board from
moisture first. Slide it under the house siding all the way around the
foundation, as shown in Fig. 4.13. Fit successive strips closely against
each other.
Cut sections of foam board the depth of the trench plus the depth of the
foundation which is exposed above the ground. Apply horizontal strips of
adhesive mastic to one side of the board, about 10-12 inches apart. Press
board into place on the foundation (Fig. 4.14). Do not cover the
foundation vents. Fit successive boards closely against each other.
Staple a vapor barrier of 6 mil polyethylene or similar material over the
entire expanse of the foam board to protect it from moisture; or, cover
with a good vapor barrier paint.
Above the ground, foam board must be covered with cement board
or stucco similar in texture and appearance to the foundation walls.
Apply it with adhesive mastic, fitting the board securely against the metal
flashing and covering the entire expanse of insulation exposed above the
ground.
Replace the soil into the trench. The access door (if located between the
floor and crawl space) and water pipes need not be insulated, as in
under-floor installations.
Interior perimeter insulation should be installed only in
geographical areas east of the Cascades. The greatest advantage of interior
perimeter insulation is that it helps protect pipes in the crawl space from
freezing. However, crawl space vents should be closed in the winter, and
the resultant moisture condensation may dampen the insulation, drastically
reducing its effectiveness. For these reasons, you should not proceed with
interior crawl space perimeter insulation without contacting your utility.
Interior perimeter insulation is attached to the band joist below the
subflooring and extended out along the ground cover for 3 feet (Fig. 4.15).
Measure the distance from the band joist to the ground in the crawl space
and add 3 feet. Cut batts or blankets of insulation to this size. Then,
precut 1 x 2s to fit between the floor joists.
Work along one of the walls running perpendicular to the joists first. Lay
one strip of polyethylene sheeting along the ground at the wall's base,
using duct tape to fasten the strip 6 inches up the foundation walls on
each end and along its length. Try not to walk on this vapor barrier as you
work.
If a ground cover is already installed, make sure it is in good condition.
Repair any tears with duct tape. Or, cover them with new plastic sheeting,
overlapping the intact part of the ground cover 12 inches and taping in
place with duct tape.
Beginning in one corner, push a batt of insulation firmly up against the
subflooring and fasten it with 1 x 2s as shown in
Fig. 4.16. Nail through the 1 x 2 and the
insulation into the joist.
Cover the entire wall, fitting each successive blanket or batt up close
against the one before it. Repeat the process for the wall that runs
parallel to it. (Do not cover any foundation vents. Cut insulation to fit
around all vents.) Do the same for the walls that run parallel to the
joists, but this time cut the blanket just long enough to reach the ground.
Next, finish laying the ground cover vapor barrier. This serves to keep
ground moisture from soaking the insulation.
Clear the crawl space floor first of any debris which might puncture or
tear the ground cover. The ground cover is held in place with sand or
coarse gravel or bricks.
Make sure you use enough plastic so that the ground cover fits snugly
against the foundation, avoiding the "bathtub" effect.
Tuck the ends of the polyethylene up under the insulation 6 inches up the
walls parallel to the joists. Lap seams of each successive sheet 12 inches.
Tape the sheeting to the foundation wall under the insulation.
Finally, lay a 3-foot-wide batt or blanket of insulation along the ground
at the walls parallel to the joists. Tape all seams with duct tape along
their entire length.
Ventilation in the crawl spaces fitted with perimeter insulation poses
special problems. Vents must be closed in order to retain heat in the
winter, but they must be opened in the summer to prevent moisture
condensation in the insulation. If you have installed perimeter insulation,
you must plug and seal all foundation vents from October through May. Open
them during the summer months. More information about ventilation is
included in Section IX, Vapor Barriers and Ventilation Control.
Next: Insulating Pipes and Ducts
|
|
|