Saudi Arabia |
SAU/486 |
Plastics hoses (HS 2004)
Saudi Arabia
Plastics hoses (HS 2004)
This International Standard specifies the requirements for three types of helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use in the ambient temperature range from -10oC to 55oC.
The three types of hose are for light -, medium- and heavy-duty applications.
The types of hoses covered in this International Standard are not intended for use with flammable or combustible materials, nor with aromatic solvents. |
12/18/2012 |
2/18/2013 |
Saudi Arabia |
SAU/493 |
Plastics hoses (HS 2004)
Saudi Arabia
Plastics hoses (HS 2004)
This International Standard specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from -10oC to + 60oC.
The four types are classified as light service for a maximum working pressure of 7 bar at 23oC and 4,5 bar at 60oC, medium service for a maximum working pressure of 10 bar at 23oC and 6,5 bar at 60oC, heavy service for a maximum working pressure of 16 bar at 23oC and 11 bar at 60oC, and heavy service for use in mining for a maximum working pressure of 25 bar at 23oC and 13 bar at 60oC. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/494 |
Rubber hoses and hose assemblies (HS 2004)
Saudi Arabia
Rubber hoses and hose assemblies (HS 2004)
This International Standard specifies the requirements for flexible rubber hoses and hose assemblies used for the transfer of metered quantities of liquefied petroleum gases (LPGs) from dispensing equipment to motor vehicles.
The hoses and hose assemblies specified in this International Standard are intended for use "wet", i.e. permanently filled with liquid, in the temperature range from -40°C to + 60°C. The maximum working pressure is 20 bar (2 MPa). |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/491 |
Rubber hoses (HS 2004)
Saudi Arabia
Rubber hoses (HS 2004)
This International Standard specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar1) with an operating-temperature range of -40oC to 70oC, depending on the type and category. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/487 |
Plastics hose (HS 2004)
Saudi Arabia
Plastics hose (HS 2004)
This International Standard specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of -10°C to +55°C.
Such hoses are classified into four types, as follows:
- low pressure, designed for a maximum working pressure of up to 4,0 bar at 23°C and up to 2,0 bar at 55°C;
- medium pressure, for a maximum working pressure of up to 7,0 bar at 23°C and up to 3,6 bar at 55°C;
- high pressure, for a maximum working pressure of up to 10,0 bar at 23°C and up to 5,1 bar at 55°C;
- extra-high pressure, for a maximum working pressure of up to 15,5 bar at 23°C and up to 7,9 bar at 55°C.
This standard does not apply to products used for fire-fighting or the conveyance of drinking water. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/488 |
Rubber hoses and hose assemblies (HS 2004)
Saudi Arabia
Rubber hoses and hose assemblies (HS 2004)
This International Standard specifies the requirements for textile- and steel-reinforced rubber hoses and hose assemblies for use with water-based and/or oil-based muds, up to a maximum temperature of 82 C, which are pumped at high pressure in large volumes in rotary drilling service and which, when tested in accordance with ISO 2977, have a minimum aniline point of 66oC.
This International Standard applies to hoses which are suitable for use at ambient temperatures between -20oC and + 52oC, unless changed by a supplementary requirement on request of the purchaser, and are resistant to ageing and tropical conditions. This International Standard does not apply to hoses which are intended for use with gases. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/492 |
Rubber hoses and hose assemblies (HS 2004)
Saudi Arabia
Rubber hoses and hose assemblies (HS 2004)
This International Standard specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 25 bar (2,5 MPa) within the temperature range -30oC to 70oC or, for low-temperature hoses (designated -LT), within the temperature range 50oC to y70oC |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/489 |
Rubber hoses (HS 2004)
Saudi Arabia
Rubber hoses (HS 2004)
This International Standard specifies requirements for three types of flexible rubber hose for pressure spraying of agro-pharmaceutical and/or fertilizer products within a temperature range of -10°C to + 60°C. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/490 |
Rubber hose and hose assemblies (HS 2004)
Saudi Arabia
Rubber hose and hose assemblies (HS 2004)
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate. Each type is divided into two classes having either an oil resistant or non-oil resistant cover. |
12/19/2012 |
2/19/2013 |
Saudi Arabia |
SAU/495 |
Motor Vehicles
Saudi Arabia
Motor Vehicles
This Standard specifies the requirements additional to ISO 15550 for determining the power of marine propulsion reciprocating internal combustion (RIC) engines when presented for documenting and checking of the declared (rated) power published by the manufacturer. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/503 |
Small craft
Saudi Arabia
Small craft
This Standard specifies requirements for electrically operated direct-current bilge pumps intended for use in removing bilge water from small craft with a hull length up to 24 m. It applies to electrically operated bilge pumps rated for less than 50 V direct current (d.c.). This International Standard does not cover pumps intended for damage control. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/500 |
ICS 47.080
Saudi Arabia
ICS 47.080
This Standard specifies the requirements additional to ISO 15550 for determining the power of marine propulsion reciprocating internal combustion (RIC) engines when presented for documenting and checking of the declared (rated) power published by the manufacturer. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/509 |
Motorcycle tyres
Saudi Arabia
Motorcycle tyres
This Saudi/ draft technical regulation is concerned with test methods for verifying the capabilities of tyres for motorcycles. Of the test methods presented, only some may be required depending on the type of tyre to be tested. The tests are carried out in the laboratory under controlled conditions. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/496 |
Motor vehicles
Saudi Arabia
Motor vehicles
This standard specifies the requirements additional to ISO 15550 for determining the power of marine propulsion reciprocating internal combustion (RIC) engines when presented for documenting and checking of the declared (rated) power published by the manufacturer. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/501 |
Small craft
Saudi Arabia
Small craft
This standard establishes uniformity of definitions of main dimensions and related data, and of mass specifications and loading conditions. It applies to small craft having a length of the hull of up to 24 m. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/499 |
Small craft
Saudi Arabia
Small craft
This Standard specifies requirements, test methods, manuals for both the owner and the installer, and the designation for hydraulic steering systems and components from the wheel to the interface Point for outboard motor, inboard motor and inboard-Outdrive steering arrangements, used on small craft of up to 24 m length of hull. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/502 |
Small craft
Saudi Arabia
Small craft
This Standard specifies requirements and test methods for remote push-pull cable steering systems and their major component items, used for small craft with single and twin installations of outboard motors of over 15 kW power, and all inboard motors, inboard motor-outdrives, and water jet drives. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/510 |
Vehicle belt drives
Saudi Arabia
Vehicle belt drives
This Saudi/ draft technical regulation is concerned with the characteristics of synchronous pulleys for use in automotive applications of synchronous endless belt drives. The characteristics include:
-tooth dimensions and tolerances;
-pulley tolerances and quality specifications. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/507 |
Small craft
Saudi Arabia
Small craft
This Standard specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol and diesel oil designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/508 |
Small craft
Saudi Arabia
Small craft
This Standard covers permanently installed liquefied petroleum gas (LPG) systems and LPG burning appliances on small craft of hull length up to 24 m, except for systems used on LPG-fuelled propulsion engines or LPG-driven generators. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/504 |
Small craft
Saudi Arabia
Small craft
This International Standard establishes requirements for the uniform display of information to be exhibited on the builder's plate of small craft with a hull length LH of up to 24 m, measured according to ISO 8666. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/506 |
Small craft
Saudi Arabia
Small craft
This Standard describes test methods and requirements for the design of electrical devices to be used on small craft so that they may be operated in an explosive atmosphere without igniting surrounding flammable gases |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/498 |
Small craft
Saudi Arabia
Small craft
This Standard specifies the information that shall be included in the owner's manual of small craft of hull length up to 24 m. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/505 |
Small craft
Saudi Arabia
Small craft
This Standard lists items to be included in the maximum load of small craft without exceeding the limits set by other ISO standards for stability, freeboard, flotation and crew. It further sets requirements for seating of crew members. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/497 |
Motor vehicles
Saudi Arabia
Motor vehicles
This Standard specifies the requirements additional to ISO 15550 for determining the power of marine propulsion reciprocating internal combustion (RIC) engines when presented for documenting and checking of the declared (rated) power published by the manufacturer. |
1/11/2013 |
3/11/2013 |
Saudi Arabia |
SAU/511 |
Machinery
Saudi Arabia
Machinery
This Saudi draft technical regulation is concerned with designed-in means aimed at preventing unexpected machine start-up (see 3.2) to allow safe human interventions in danger zones (see annex A). |
1/21/2013 |
3/21/2013 |
Saudi Arabia |
SAU/515 |
Amusement rides and devices
Saudi Arabia
Amusement rides and devices
This Saudi draft technical regulation is concerned with the basic tests which shall be conducted on amusement rides and devices during prototype development, installation or erection, following major modifications, and during normal operation to determine that the performance of a given ride or device meets the manufacturer's specified design criteria. |
1/21/2013 |
3/21/2013 |
Saudi Arabia |
SAU/514 |
Lift (elevators), escalators and moving walks
Saudi Arabia
Lift (elevators), escalators and moving walks
This Saudi draft technical regulation is concerned which general principles and specific procedures for assessing risk. The purpose of this International Standard is to provide a process for making decisions relevant to the safety of lifts during the: a) design, construction, installation and servicing of lifts, lift components and systems; b) development of generic procedures for the use, operation, testing, compliance verification and servicing of lifts and; c) development of technical specifications and standards affecting the safety of lifts. |
1/21/2013 |
3/21/2013 |
Saudi Arabia |
SAU/513 |
Machinery
Saudi Arabia
Machinery
This Saudi draft technical regulation is concerned with a procedure which leads to the selection of critical factors relating to emissions of hazardous substances for the purpose of specifying suitable verification procedures. This part of ISO 14123 is intended to be used in conjunction with ISO 14123-1 and relates specifically to clause 8 of that standard. |
1/21/2013 |
3/21/2013 |
Saudi Arabia |
SAU/512 |
Machinery
Saudi Arabia
Machinery
This Saudi draft technical regulation is concerned with methods for identifying fire hazards resulting from machinery and performing a corresponding risk assessment. It gives the basic concepts and methodology of technical fire prevention and protection measures to be taken during the machinery's design and construction. |
1/21/2013 |
3/21/2013 |
Saudi Arabia |
SAU/524 |
Radiation protection instrumentation
Saudi Arabia
Radiation protection instrumentation
General characteristics, General test procedures, Radiation characteristics, Electrical characteristics, Electromagnetic compatibility, Mechanical characteristics, Environmental characteristics and documentation. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/522 |
Gas chromatograph/mass spectrometer systems
Saudi Arabia
Gas chromatograph/mass spectrometer systems
Description of the instrument, Metrological requirements, Technical requirements, Practical instructions, Metrological controls. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/521 |
Gas chromatographic systems
Saudi Arabia
Gas chromatographic systems
Description of the instrument, Metrological requirements, Technical requirements, Practical instructions, Metrological controls. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/519 |
Conductivity of electrolytes
Saudi Arabia
Conductivity of electrolytes
Terminology, Standard solutions. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/518 |
Sound level meters
Saudi Arabia
Sound level meters
Construction and maximum permissible errors, Stability, Inscription, marking and instruction manual. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/517 |
Fuel dispensers
Saudi Arabia
Fuel dispensers
Test equipment and test conditions, testing procedures, additional testing procedures for electronic dispensers, test report format and check list. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/516 |
Fuel dispensers for motor vehicles
Saudi Arabia
Fuel dispensers for motor vehicles
Test equipment and test conditions, testing procedures, additional testing procedures for electronic dispensers, test report format and check list. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/520 |
Automatic gravimetric filling instruments
Saudi Arabia
Automatic gravimetric filling instruments
Metrological requirements, Technical requirements, Requirements for electronic instruments, Metrological controls, Test methods, Testing procedures for automatic gravimetric filling instruments. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/523 |
Dynamic measuring systems for liquids other than water
Saudi Arabia
Dynamic measuring systems for liquids other than water
General requirements, Requirements for meters and ancillary devices of a measuring system, Measuring systems equipped with electronic devices , Requirements specific to certain types of measuring systems, Metrological control and Type approval performance tests. |
1/31/2013 |
3/31/2013 |
Saudi Arabia |
SAU/525 |
Foodstuffs
Saudi Arabia
Foodstuffs
Draft of Technical Regulation for Nutritional and Health Claims Requirement |
2/7/2013 |
4/7/2013 |