Central Supply
Click on the area for more specific information.
|
Common safety and health topics:
Exposure to Ethylene Oxide Gas (EtO)
Ethylene Oxide (EtO) possesses several physical and health hazards that merit special attention. EtO is a
colorless liquid below 51.7°F, or a gas that has an ether-like odor at concentrations above 700 parts
per million (ppm) and is both flammable and highly reactive. The current OSHA Permissible Exposure Limit (PEL) for EtO is 1 ppm for
an 8hr time weighted average with a 5ppm excursion level.
Potential Hazard
Staff exposure to EtO. EtO is used within central supply as a sterilant for items that can not be exposed to steam
sterilization. Exposure usually results from improper aeration of the ethylene oxide chamber after
the sterilizing process or during off-gassing of sterilized items or poor gas-line connections. It can also occur in outpatient surgery
clinics, cardiac catheterization laboratories, operating rooms, dental labs, autopsy labs and other areas.
Health Effects:
-
In liquid form, Ethylene oxide can cause eye irritation and injury to the cornea, frostbite, and severe irritation and blistering of
the skin upon prolonged or confined contact.
-
Ingesting EtO can cause gastric irritation and liver injury. Acute effects from
inhaling EtO vapors include respiratory irritation and lung injury, headache, nausea, vomiting, diarrhea, shortness of breath, and cyanosis.
-
Exposure has also been associated with the occurrence of cancer, reproductive effects, mutagenic changes, neurotoxicity, and
sensitization. Ethylene oxide has been shown to cause cancer in laboratory animals and has been associated with higher incidences
of cancer in humans. Adverse reproductive effects and chromosome damage may also occur from EtO exposure.
Possible Solutions
- Substitute other cold sterilants for EtO. However, use extreme care when selecting possible substitutes. It is necessary to fully evaluate possible health effects
and exposure potentials of alternatives to EtO before making a selection.
-
Use proper ventilation with EtO gas.
-
Typical operations that could cause worker exposure to EtO are removing sterilized items
from the EtO sterilizer, moving items from the EtO sterilizer to the aerator unit, and changing bottles of EtO
gas. You can control airborne concentrations of EtO most effectively at the source of contamination by
enclosing the operation and/or using local exhaust ventilation.
-
Reduce exposure to EtO during the sterilization process.
- Do not occupy the sterilizer loading and mechanical rooms while operating the sterilizer unit.
- Operators should crack the door no more than two inches and allow the load to "off gas" before
moving to transfer carts. A ventilated exhaust hood should be installed above the sterilizer door.
- Operators should avoid close contact with newly sterilized unaerated loads.
-
Vent ethylene oxide through a non-recycled or dedicated ventilation system. For a discussion
of ventilation of aeration units, sterilizer door areas, sterilizer relief valves, and ventilation during cylinder
changes, see the appendix of 29 CFR 1910.1047
(Ethylene Oxide).
-
To detect inadequate ventilation and cause automatic shutdown have machine alarms
in place. Air pressure in laboratories and isolation rooms should be negative so that contaminated air is drawn through the exhaust vents rather
than circulating throughout the rest of the building.
-
Use appropriate PPE when changing cylinders including butyl apron, gloves, and a canister respirator.
-
Use EtO detector systems and room monitors to signal any leakage of gas, and passive dosimeters for personal exposure
monitoring.
-
Use specialized gas-line connections to minimize EtO leakage during use and during change out of EtO
cylinders.
-
Conduct periodic personal monitoring, as well as, monitoring for leaks at gas-line connectors.
EtO Room Monitor |
Passive Dosimeter for personal exposure monitoring |
EtO Monitoring Station |
Additional Information:
|
Potential Hazard
Employees can be exposed to mercury from accidental spills that occur during sterilization and centrifugation of
thermometers in central supply areas. Exposure to mercury occurs through inhalation or through skin contact. If spills are not
promptly cleaned up, mercury may accumulate on surfaces and then vaporize and be inhaled by unaware workers.
Possible Solutions
-
Prevent the spill in the first place by replacing outdated glass thermometers
and sphygmomanometers.
-
Make sure that spills are cleaned up promptly and safely, by workers or a team trained in proper procedures.
-
Periodically train employees to understand procedures and to correctly follow policies, (e.g., procedures in place
that provide for isolation of the contaminated area).
-
Have spill kits available to help clean up small spills of
25 ml or less.
For additional information, see Healthcare Wide Hazards -
Mercury.
|
Potential Hazard
Employee exposure to glutaraldehyde, found in products such as Cidex, Aldesen, Hospex and others, when instruments or other items are
cold sterilized in central supply.
Possible Solutions
- Store glutaraldehyde products in closed containers, in well ventilated areas. Post signs to remind staff to replace lids after
using product.
- Use glutaraldehyde products in rooms that are well ventilated and large enough to ensure adequate dilution of vapor, with a minimum
air exchange rate of 10 air changes per hour. Ideally, install local exhaust ventilation such as a properly functioning laboratory
fume hood to control vapor.
- Use appropriate PPE to minimize exposure including:
- Gloves which are impervious to glutaraldehyde such as those made of Butyl Rubber, Nitrile, and
Viton® which have been shown to provide full shift protection from glutaraldehyde.
- Splash proof goggles and/or full-face shields when working with glutaraldehyde to protect eyes.
For additional information, see Healthcare Wide Hazards -
Glutaraldehyde,
PPE,
Hazardous Chemicals.
|
Bloodborne Pathogens (BBP)
As mandated by the Needlestick Safety and Prevention Act, OSHA revised the Bloodborne Pathogens Standard [29 CFR 1910.1030], effective April 18, 2001.
Potential Hazard
Employee exposure to BBP and other potentially infectious materials as bloody, contaminated surgical instruments and sharps (e.g., needles, scalpels) are sorted. Employee must discard any disposable sharps and recycle reusable instruments/equipment that need to be washed and sterilized before their next use.
Possible Solutions
- Wear appropriate PPE as required by the Bloodborne Pathogens Standard 29 CFR 1910.1030(d)(3)(i) if blood or Other Potentially Infectious Materials (OPIM) exposure is
anticipated. The type and amount of PPE depends on the anticipated
exposure including:
- Gloves must be worn when hand contact with blood, mucous membranes,
OPIM, or non-intact skin is anticipated, or when handling contaminated items or
surfaces [29 CFR 1910.1030(d)(3)(ix)].
- Wearing thick utility gloves and gowns can offer additional protection to the employee sorting contaminated items.
- Utility gloves may be decontaminated for re-use if the integrity of the glove is not compromised. However, they must be
discarded if they are cracked, peeling, torn, punctured, or exhibit other signs of deterioration or when their ability to function as a barrier is
compromised. [29 CFR 1910.1030(d)(3)(ix)(C)].
The Bloodborne Pathogens Standard also requires:
- Discarding contaminated needles and other sharp instruments immediately or as soon as feasible after use into appropriate containers
[29 CFR 1910.1030(d)(4)(iii)(A)(1)].
For additional information see Healthcare Wide Hazards -
Bloodborne Pathogens.
|
Ergonomics
Ergonomics is the science of fitting the job to the worker. When there is a mismatch between the physical requirements of the job and the physical capacity of the worker,
work-related Musculoskeletal Disorders (MSD) can result.
Potential Hazard
Reaching/Lifting |
Employee exposure to MSD from repetitive, prolonged, reaching, when sorting sterilized packages or lifting above shoulder height to reach high shelves of equipment or when
pushing and pulling heavy carts full of dirty or clean items. Static postures may occur from continuously standing in one position while sorting
instruments. Contact trauma to forearm area can occur if employee rests wrists on hard sharp counter surfaces when sorting.
Possible Solutions
-
|
Well maintained cart
| Redesign workstations so packaging and equipment can be reached while maintaining the elbows in close to the body.
- Use carts with large, low rolling, low resistance wheels, that can easily roll over mixed flooring as well as gaps between elevators and
hallways.
- Minimize prolonged overhead activity (e.g., lower stacking shelves to shoulder height).
- Use height-adjustable work surfaces or lift tables to minimize head tilt.
-
Rotate workers through repetitive tasks.
|
Padded Work
Surfaces
|
- Pad the edge of work surfaces which come into contact with the elbow or forearm which could cause contact trauma.
- Provide sit/stand stools at work stations.
- Use anti-fatigue mats.
- Use shoes with well-cushioned insteps and soles where floor mats cannot be used.
- Provide a foot rest bar so employees can continually alter their posture by raising one foot.
Sit/Stand Stool
|
For additional information see Healthcare Wide Hazards -
Ergonomics.
|
Potential Hazard
Employee exposure to hazardous chemicals that may be used in the initial washing process of dirty instruments.
-
Unlabeled chemicals and untrained employees.
-
Not using appropriate personal protective equipment when handling hazardous chemicals which may be found in soaps,
disinfectants, cleaners, etc.
Possible Solutions
-
Implement a written program that meets the requirements of the
Hazard Communication Standard to provide for worker training, warning labels, and access to Material Safety Data Sheets (MSDS).
-
Provide appropriate PPE: (e.g., gloves, goggles, splash aprons) when handling hazardous dishwashing
detergents and chemicals [29 CFR 1910.132].
For additional information, see Healthcare Wide Hazards - PPE.
-
Medical Services and First Aid: Where the eyes or body of any person may be exposed to injurious corrosive
materials, provide suitable facilities for quick drenching or flushing the eyes and body within the
work area for immediate emergency use [29 CFR 1910.151(c)].
- Use dishwashing machines that automate the dispensing of washing chemicals to minimize employee exposure to chemicals. Workers
must still be cautious and use appropriate PPE (e.g., goggles, and/or gloves) when changing out the containers of detergent.
For additional information, see Healthcare Wide Hazards -
Hazardous Chemicals.
|
|
Potential Hazard
Employee exposure to slippery floors from steam and washing processes.
Possible Solutions
-
Keep floors clean and dry [29 CFR 1910.22(a)(2)].
In addition to being a slip hazard, continually wet surfaces promote the growth of mold, fungi, and bacteria which can
cause infections.
-
Keep aisles and passageways clear and in good repair, with no obstruction across or in aisles that could create a hazard
[29 CFR 1910.22(b)(1)].
Provide floor plugs or ceiling plugs for equipment, so power cords need not run across pathways.
For additional information, see Healthcare Wide Hazards -
Slips/Trips/Falls.
|
Potential Hazard
Employee exposure to latex and latex allergy from wearing gloves when handling and sorting contaminated, bloody
equipment, or when handing sterile equipment.
Possible Solutions
-
Employers must provide appropriate gloves when exposure to blood or other potentially infectious materials
(OPIM) exists [29 CFR 1910.1030
Bloodborne Pathogens Standard].
-
Make alternatives readily accessible to those employees who are allergic to the gloves normally provided
[29 CFR 1910.1030(d)(3)(iii)].
For additional information, see Healthcare Wide Hazards -
Latex Allergy.
|
Accessibility Assistance: Contact the OSHA Directorate of Technical Support and Emergency Management at (202) 693-2300 for assistance accessing PDF materials.
|
|
|