Consumer Factsheet on: CYANIDE
List of
Contaminants
As part of the Drinking Water and Health pages, this fact
sheet is part of a larger publication: National Primary Drinking Water
Regulations
This is a factsheet about a chemical that may be found in some public or
private drinking water supplies. It may cause health problems if found in
amounts greater than the health standard set by the United States Environmental
Protection Agency (EPA).
What is Cyanide and how is it used?
Cyanide is a carbon-nitrogen chemical unit which combines with many organic
and inorganic compounds. The most commonly used form, hydrogen cyanide, is
mainly used to make the compounds needed to make nylon and other synthetic
fibers and resins. Other cyanides are used as herbicides.
Why is Cyanide being regulated?
In 1974, Congress passed the Safe Drinking Water Act. This law requires EPA
to determine safe levels of chemicals in drinking water which do or may cause
health problems. These non-enforceable levels, based solely on possible health
risks and exposure, are called Maximum Contaminant Level Goals.
The MCLG for cyanide has been set at 0.2 parts per million (ppm) because EPA
believes this level of protection would not cause any of the potential health
problems described below
Based on this MCLG, EPA has set an enforceable standard called a Maximum
Contaminant Level (MCL). MCLs are set as close to the MCLGs as possible,
considering the ability of public water systems to detect and remove
contaminants using suitable treatment technologies
The MCL has been set at 0.2 ppm because EPA believes, given present
technology and resources, this is the lowest level to which water systems can
reasonably be required to remove this contaminant should it occur in drinking
water. These drinking water standards and the regulations for ensuring these
standards are met, are called National Primary Drinking Water Regulations. All
public water supplies must abide y these regulations
What are the health effects?
Short-term: EPA has found cyanide to potentially cause the following health
effects when people are exposed to it at levels above the MCL for relatively
short periods of time: rapid breathing, tremors and other neurological
effects
Long-term: Cyanide has the potential to cause the following effects from a
lifetime exposure at levels above the MCL: weight loss, thyroid effects, nerve
damage
How much Cyanide is produced and released to the environment?
Production of the most common cyanides was roughly 5 billion pounds a year
in the late 1980s and early 1990s. The major cyanide releases to water are
discharges from metal finishing industries, iron and steel mills, and organic
chemical industries. Releases to soil appear to be primarily from disposal of
cyanide wastes in landfills and the use of cyanide-containing road salts.
Chlorination treatment of some wastewaters can produce cyanides as a
by-product
From 1987 to 1993, according to the Toxics Release Inventory cyanide
compound releases to land and water totaled about 1.5 million lbs. These
releases were primarily from steel mills and metal heat treating industries.
The largest releases occurred in California and Pennsylvania
What happens to Cyanide when it is released to the environment?
Cyanides are generally not persistent when released to water or soil, and
are not likely to accumulate in aquatic life. They rapidly evaporate and are
broken down by microbes. They do not bind to soils and may leach to ground
water.
How will Cyanide be detected in and removed from my drinking water?
The regulation for cyanide became effective in 1992. Between 1993 and 1995,
EPA required your water supplier to collect water samples once and analyze them
to find out if cyanide is present above 0.2 ppm. If it is present above this
level, the system must continue to monitor this contaminant every 3 months.
If contaminant levels are found to be consistently above the MCL, your water
supplier must take steps to reduce the amount of cyanide so that it is
consistently below that level. The following treatment methods have been
approved by EPA for removing cyanide: Ion Exchange, Reverse Osmosis,
Chlorine
How will I know if Cyanide is in my drinking water?
If the levels of cyanide exceed the MCL, the system must notify the public
via newspapers, radio, TV and other means. Additional actions, such as
providing alternative drinking water supplies, may be required to prevent
serious risks to public health
This is a factsheet about a chemical that may be found in some public or
private drinking water supplies. It may cause health problems if found in
amounts greater than the health standard set by the United States Environmental
Protection Agency (EPA)
Drinking Water Standards:
MCLG: 0.2 ppm
MCL: 0.2 ppm
Cyanide Releases to Water and Land, 1987 to 1993 (in pounds):
|
Water |
Land |
TOTALS |
939,611 |
641,082 |
|
Top Ten States
| |
CA |
0 |
430,886
|
PA |
208,239 |
4,909
|
IN |
187,377 |
20,242
|
OH |
160,203 |
850
|
TX |
54,379 |
83,394
|
MD |
89,438 |
23,503
|
|
Major Industries
| |
Blast furnaces + steel |
747,970 |
53,404
|
Metal heat treating |
0 |
430,886
|
Ind organic chems |
49,098 |
82,912
|
Plating + polishing |
29,486 |
29,636
|
Learn more about your drinking water!
EPA strongly encourages people to learn more about their drinking water, and
to support local efforts to protect and upgrade the supply of safe drinking
water. Your water bill or telephone books government listings are a good
starting point.
Your local water supplier can give you a list of the chemicals they test for
in your water, as well as how your water is treated.
Your state Department of Health/Environment is also a valuable source of
information.
For help in locating these agencies or for information on drinking water in
general, call: EPAs Safe Drinking Water Hotline: (800) 426-4791
For additional information on the uses and releases of chemicals in your
state, contact the: Community Right-to-Know Hotline: (800) 424-9346
|