DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
49 CFR Part 575
[Docket No. NHTSA-2000-8298]
Consumer Information Regulations;
Federal Motor Vehicle Safety Standards;
Rollover Resistance
AGENCY: National Highway Traffic Safety Administration (NHTSA), DOT.
ACTION: Response to Comments, Notice of Final Decision
SUMMARY: The agency has concluded that consumer information on the rollover risk of passenger cars and light multipurpose passenger vehicles and trucks will reduce the number of rollover crashes and the number of injuries and fatalities from rollover crashes. This information will enable prospective purchasers to make choices about new vehicles based on differences in rollover risk and serve as a market incentive to manufacturers in striving to design their vehicles with greater rollover resistance. The consumer information program will also inform drivers, especially those who choose vehicles with poorer rollover resistance, that their risk of harm can be greatly reduced with seat belt use to avoid ejection.
The agency has decided to use the Static Stability Factor to indicate rollover risk in single-vehicle crashes and to incorporate the new rating into NHTSA's New Car Assessment Program (NCAP). As part of these ratings, the agency also has decided to note vehicles that are equipped with "electronic stability control" technology, which may reduce the risk of a vehicle getting into an incipient rollover situation. This notice summarizes the comments received in response to the agency's June 1, 2000 Request for Comment regarding the addition of rollover ratings based on SSF to NCAP, our response to those comments, and the procedures and protocol we will use to implement a new rollover consumer information program.
FOR FURTHER INFORMATION CONTACT: For the most up to date vehicle star ratings call the Auto Safety Hotline at 888-327-4236 or refer to NHTSA's website at www.nhtsa.dot.gov. For technical questions you may contact Gayle Dalrymple, NPS-23, Office of Safety Performance Standards, National Highway Traffic Safety Administration, 400 Seventh Street, SW, Washington, DC 20590. Ms. Dalrymple can be reached by phone at (202) 366-5559 or by facsimile at (202) 493-2739. For public comments and other information related to previous notices on this subject, please refer to:
DOT Docket No. NHTSA-2000-6859, Docket Management, Room PL-403, 400 Seventh Street, SW, Washington, D.C. 20590 (hours 10:00 a.m. to 5:00 p.m. Monday through Friday) or on the internet at http://dms.dot.gov/search/ and Docket No. 91-68; Notice 3, NHTSA Docket, Room PL-403, 400 Seventh Street, SW, Washington, DC 20590. NHTSA Docket hours are from 9:30 am to 4:00 pm Monday through Friday.
SUPPLEMENTARY INFORMATION:
I. Introduction
II. Background
III. Discussion of Commenters' Issues
A. SSF as a Measure of Rollover Risk
B. NHTSA's Statistical Analysis Linking SSF to Rollover Rates
C. Comments on Practical Problems with SSF Ratings
D. Consumer's Ability to Understand SSF as a Measure of Rollover Risk in the Event of a Single-vehicle Crash
E. The Question of Electronic Stability Control
F. Alternative Programs Suggested by Commenters
G. Commenters' Desire for a Minimum Standard Based on a Dynamic Test
IV. Rollover Information Dissemination using SSF in NCAP
V. Rulemaking Analyses and Notices
Appendix I Statistical Analysis in Response to Comments
Appendix II Proposed List of Test Vehicles for MY2001
I. Introduction
This notice outlines the plan the National Highway Traffic Safety Administration (NHTSA) will use to incorporate a new rollover rating of new cars and light trucks into its existing New Car Assessment Program (NCAP). NCAP currently gives consumers crashworthiness ratings for new light vehicles in frontal and side crashes. The ratings are based on vehicle performance with respect to occupant injury criteria gathered in crash tests and are presented using one to five stars, one star for the highest risk and five for the lowest. We intend to use the same star rating system to present the risk of rollover in the event of a single-vehicle crash. One star would represent a Static Stability Factor (SSF) corresponding to a 40 percent or greater risk of a single-vehicle crash resulting in rollover, while five stars would represent an SSF corresponding to a risk of less than 10 percent. Static Stability Factor is one-half the track width of a vehicle divided by the height of its center of gravity. As part of the rating based on SSF, the agency also has to note vehicles that are equipped with "electronic stability control" technology, which may reduce the risk of a vehicle getting into an incipient rollover situation.
The agency requested comments on its tentative decision to implement such a program on June 1, 2000.(1) The closing date for comments was August 30, 2000. Twenty-five commenters responded. This notice addresses the major issues presented by the commenters, our response to those comments, and the procedures and protocol we will use to implement a rollover consumer information program based on SSF. For complete background and rationale for the program, please see the June 1, 2000 notice.
II. Background
Rollover crashes are complex events that reflect the interaction of driver, road, vehicle, and environmental factors. We can describe the relationship between these factors and the risk of rollover using information from the agency's crash data programs. We limit our discussion here to light vehicles, which consist of (1) passenger cars and (2) multipurpose passenger vehicles and trucks under 4,536 kilograms (10,000 pounds) gross vehicle weight rating (collectively, "light trucks").(2)
According to the 1999 Fatality Analysis Reporting System (FARS), 10,142 people were killed as occupants in light vehicle rollovers, including 8,345 killed in single-vehicle rollovers. Eighty percent of the people who died in single-vehicle rollovers were not using a seat belt, and 64 percent were ejected from the vehicle (including 53 percent who were completely ejected). FARS shows that 55 percent of light vehicle occupant fatalities in single-vehicle crashes involved rollover. The proportion differs greatly by vehicle type: 46 percent of passenger car occupant fatalities in single-vehicle crashes involved rollover, compared to 63 percent for pickup trucks, 60 percent for vans, and 78 percent for sport utility vehicles (SUVs).
Using data from the 1995-1999 National Automotive Sampling System (NASS) we estimate that 253,000 light vehicles were towed from a rollover crash each year (on average), and that 27,000 occupants of these vehicles were seriously injured (defined as an Abbreviated Injury Scale (AIS) rating of at least 3).(3) This includes 205,000 single-vehicle tow-away rollovers with 19,000 serious injuries. Sixty-five percent of those people who suffered a serious injury in single-vehicle tow-away rollovers were not using a seat belt, and 50 percent were ejected (including 41 percent who were completely ejected). Estimates from NASS are that 81 percent of tow-away rollovers occurred in single-vehicle crashes, and 87 percent (178,000) of the single-vehicle rollover crashes occurred after the vehicle left the roadway.
Based on the 1995-1999 General Estimates System (GES) data we estimate that 241,000 light vehicles rolled over each year (on average) in police-reported crashes, and that 57,000 occupants in rollover crashes received injuries rated as K or A on the police injury scale. (The police KABCO scale calls these injuries "incapacitating," but their actual severity depends on local practice. "Incapacitating" injury may mean that the injury was visible to the reporting officer or that the officer called for medical assistance.) This includes 205,000 single-vehicle rollovers with 46,000 K or A injuries. Fifty-four percent of those with K or A injury in single-vehicle rollovers were not using a seat belt, and 20 percent were ejected from the vehicle (including 18 percent who were completely ejected). Estimates from GES are that 16 percent of light vehicles in police-reported single-vehicle crashes rolled over. The estimated risk of rollover differs by vehicle type: 13 percent of cars and 14 percent of vans in police-reported single-vehicle crashes rolled over, compared to 24 percent of pickup trucks and 32 percent of SUVs.
The data presented above demonstrate that rollover crashes create a serious safety problem and that a reduction in the number of rollovers can make a significant contribution to motor vehicle safety.
III. Discussion of Commenters' Issues
The Request for Comment (RFC) was published June 1, 2000. The comment period closed August 30, 2000. Twenty-five commenters replied. The respondents were vehicle manufacturers and their associations, testing laboratories, independent researchers, consumer safety groups, an insurance association, a trial attorney, and two consumers. Two commenters agreed with the inclusion of rollover rating in NCAP as it was presented in the RFC. The other commenters were divided among those who opposed the plan (manufacturers, dealers, testing labs) and those who thought it did not go far enough - that a minimum standard, based on a dynamic test, is needed for rollover (trial attorney, consumer groups). The commenters raised issues in four areas:
Alternative consumer information programs for rollover prevention were also offered by some commenters. Those four issues and the alternative programs are discussed in this section.
A. SSF as a Measure of Rollover Risk
Many respondents to the RFC believe that SSF is not a good measure of rollover risk for various reasons. Comments and the parties that made them were the following:
1. Origin of Static Stability Factor
Static Stability Factor is not a measure of rollover resistance invented by the agency. It was introduced to the agency in 1973 by vehicle manufacturers as a scientifically valid potential substitute for the dynamic maneuver tests the agency wanted to develop regarding untripped on-road rollover.(4) The Motor Vehicle Manufacturers Association (which has evolved into the present Alliance of Automobile Manufacturers) stated the following about SSF, "Although this method does not embrace all vehicle factors relating to rollover resistance, it does involve the basic parameters of [sic] influencing resistance."
In 1973, all of the manufacturers opposed NHTSA's plans for a standard regarding rollover prevention in extreme accident avoidance maneuvers because of their expectation of negligible benefits, concern about banning vehicle types, degradation of vehicle capabilities including braking traction and handling performance, and unresolved problems with maneuver testing. General Motors presented a very detailed set of comments that remain relevant today. For example, its observations on the effect of restraint use on rollover fatality rates and on the breakdown of the rollover problem between multi-vehicle and single-vehicle crashes and on-road and off-road incidences are largely supported by present data. Likewise, its discussion of the problems of maintaining consistent pavement surface and tire traction properties, the use of automatic controls and outriggers, the types of maneuvers and their relationship to real crashes is still meaningful. We also think its comments regarding SSF (which it called geometric stability measurement) are still accurate. General Motors said:
Resistance to rollover is mainly influenced by the following factors:
1. Height of the center of gravity.
2. Horizontal distance from center of gravity to wheel track.
3. Capability for generating large forces in the lateral
direction of the tire contacts due to high tire friction.
Lateral forces sufficient for rollover can result from severe maneuvers under high tire-road friction conditions; from collisions with other vehicles, curbs, or road furniture (signs, lamp posts, guard rails), and from maneuvers in roadside soil capable of sustaining high lateral forces.
General Motors qualified the discussion as pertaining to relatively simple maneuvers, but cautioned against the use of "special " braking and steering inputs for rollover maneuver tests as unrepresentative of vehicle operation. It also discussed the relative importance of secondary vehicle characteristics other than those above which are the components of SSF.
It was noted in a previous section that the dominant factors in flat road rollover resistance are the center of gravity height, track width, and the ability of the tire-road interface to generate high levels of lateral force. Suspension geometry, component stiffness factors, allowable ride travel, and tire stiffness factors also exert a measurable influence on rollover performance. But, these latter factors are considered to be of secondary importance. It should be noted that in many cases, very careful laboratory tests are required to establish the influence of suspension modifications on rollover resistance.
In its conclusions, General Motors maintained that there was no safety need for the on-road rollover resistance standard the agency intended to propose and that, if the agency decided to act at all, it should pursue consumer information based on SSF.
If any regulation is required, some benefit may be derived at minimal cost by better informing the customer of relative product rollover performance, so he can assess this vehicle performance factor in making his selection in a free market. This information could be based on geometric stability measurements for the full range of highway vehicles.
This comment was made before the NCAP program was established to provide consumer information on safety performance and before the consumer was faced with such a large range of geometric stability (SSF) in non-commercial passenger vehicles. Also, most of the practical difficulties in seeking objective, relevant and repeatable driving maneuver tests discussed by General Motors in 1973 remain unsolved. Note that GM suggested the static laboratory measurement as a substitute for maneuver tests when only on-road untripped rollover was under consideration. This is an even stronger endorsement of static measurements than that represented by NHTSA's reasons for using SSF for consumer information on all single-vehicle rollovers, tripped and untripped.(5)
We view the rollover safety problem as 95 percent a problem of tripped rollover and five percent a problem of on-road untripped rollover. (6) Maneuver tests do not represent tripped rollover. Once the vehicle is in a tripping situation (e.g., has left the road), tire traction is largely irrelevant to tripped rollover. Center of gravity height and track width (and to a much lesser extent roll moment of inertia) are the only vehicle properties with general applicability to tripped rollover situations. So, in 95 percent of rollovers, these vehicle properties would be the most relevant vehicle influences on the likelihood of rollover. In the five percent of the problem involving untripped rollover, a choice exists between using static measurements and performance in maneuver tests. To get data to make an informed choice between the two, NHTSA conducted a maneuver test program using 12 vehicles in 1998. That testing confirmed General Motors' opinion of 25 years earlier that the static measurements correspond well to dynamic maneuver tests.(7) It also confirmed that the problems with maneuver testing identified by GM in 1973 are still largely unresolved today. Accordingly, we concluded in our June 2000 notice that there were no practical improvements in rating overall rollover resistance to be gained at this time by using something other than static measurements.
2. The Importance of the Effect of SSF on Rollover Rate
When the agency first sought public comment on rollover issues in 1973, the industry's position was that the frequency of untripped on-road rollovers was too low to justify significant vehicle modifications and constraints on future vehicle design. The vehicle manufacturers questioned the benefit/cost relationship and practicability of a minimum standard on rollover resistance, but they did not deny the relationship between SSF and rollover crashes. The agency's June 2000 plan for consumer information on rollover resistance expressed considerable agreement with the 1973 industry position on rollover and offered a statistical study of modern crash data in order to quantify the relationship between SSF and the incidence of rollovers occurring in single-vehicle crashes. The Alliance responded in August 2000 with the position that vehicle characteristics are now deemed largely irrelevant to the occurrence of rollover crashes and consumer information on vehicle rollover resistance is inherently misleading. The Alliance provided a statistical study purporting to demonstrate that the influence of SSF was limited to three to eight percent of the variability between vehicles in rollover crashes.
While the laws of physics prove beyond question that vehicles with low SSF roll over at lower lateral accelerations than vehicles with high SSF, the effect of SSF must be shown to have a significant influence on the outcome of actual crashes (rollover vs. no rollover) to be worth using for consumer information. It is a fact that types of vehicles with SSFs lower than passenger cars, as a group, have greater numbers of rollover crashes than passenger cars, either as a percentage of all crashes (passenger cars, 1.6 percent; vans, 2.0 percent; pickup trucks, 3.7 percent; SUVs, 5.1 percent) or as a percentage of single-vehicle crashes (passenger cars, 13 percent; vans, 14 percent, pickup trucks, 24 percent; SUVs, 32 percent). The Alliance attributes these differences primarily to differences in the driver and road conditions associated with the various vehicle types, rather than to the characteristics of the vehicles. For example, if young males using alcohol and driving on rural roads with high speed limits are over-represented as drivers of four-wheel drive pickup trucks in crashes, could these road-use variables outweigh the vehicle property to the point of insignificance? According to the current industry view, the correlation between the SSF of a vehicle and its ability to attract risky drivers who operate vehicles under adverse road conditions is the fundamental reason vehicles with low SSF are involved in a higher proportion of rollover crashes.
The agency agrees that driver behavior and road conditions are significant factors in understanding why single-vehicle crashes of any type occur, and that they have a strong influence on whether single-vehicle crashes result in rollover. However, we think that the rollover resistance of the vehicle represented by SSF also exerts a strong influence on whether single-vehicle crashes result in rollover. The statistical study in our previous notice attempted to address the important question of whether road-use differences between vehicles relegate their difference in rollover resistance to insignificance in actual crash experiences. We analyzed state accident reports in six states (1994-1997) on 184,726 single-vehicle crashes with 36,575 rollovers involving 100 vehicle make/models. The road-use variables available in all six states identified male drivers, young drivers, alcohol involvement, darkness, wet or icy surface, speed limit 55 mph or greater, storm, hill, and curve. We used multiple linear regression because its "R-squared statistic" provided an intuitive method of comparing the explanatory power of individual variables and because we could control the effect of the large differences in the number of crash samples for the various vehicles. Each vehicle was represented by its SSF and the average of each road-use variable over the number of crashes in each state. Systematic differences between states in rollover rate due to factors such as accident reporting thresholds were accommodated by the inclusion of a dummy variable for each state. The "R-squared statistic" for the complete model was 0.88, indicating that the model explained 88 percent of the observed differences in rollover rate per single-vehicle crash between the vehicle make/models.
The linear regression that used only the SSF and the state dummy variables as predictor variables had an "R-squared" of 0.73, which means that almost three-quarters of the variability in rollover risk between vehicle models is explained by the SSF plus the adjustments for state-to-state differences in crash reporting. This is greater than the "R-squared" for the best model that used only the road-use variables plus the state dummy variables (0.58). Thus, the SSF appears to have greater explanatory value than the combination of the road-use variables. We conclude that the SSF is not relegated to insignificance by the road-use variables in describing rollover risk.
The Alliance comment criticized the agency's use of linear regression because it operates on averages of road-use variables and cannot consider the possible interaction among variables. For example, the linear regression model would consider that the crashes of a particular make/model may involve 30 percent young drivers, 20 percent with alcohol involvement and 15 percent on curves, but it cannot distinguish crashes in which all of the factors were present simultaneously. The Alliance used logistic regression rather than linear regression in its analysis. Logistic regression operates on every individual crash circumstance sampled, rather than on averages of the road-use variables for crashes of each make/model, and thus can consider interactions among variables. It is a popular statistical tool in the health sciences. The Alliance also introduced the concept of scenario risk in its logistic regression model. In this technique, each combination of road-use variables (with some states providing as many as 14 variables) is a scenario. Scenario risk becomes a continuous variable.
Appendix I of this notice presents a new statistical study which adds another year of state crash data to the database of our previous notice and contrasts analyses of the crash data using logistic regression of individual variables and risk scenarios to the linear regression method used in the previous notice. We found that it made very little difference to the logistic regression models whether the road-use variables were used as individual variables or combined to form risk scenarios, but that the curve estimating rollovers per single-vehicle crash produced by the logistic regression was slightly different from that previously reported for linear regression.
The estimated risk of rollovers per single-vehicle crash is six times as high for a vehicle with an SSF of 1.00 as for a vehicle with an SSF of 1.53 (the range of the observed data) based on the linear regression model. The average slope of the rollover risk versus SSF curve for the linear regression model (Figure 1) in the range of observed data was -0.713. The slope of the corresponding curve of the logistic models is -0.598 or -0.580, depending on whether we use the individual variables or the scenario-risk variable. Both the linear and logistic approaches produced models that fit the data well, and both estimated a coefficient for the SSF term that was very important (in terms of statistical significance and the magnitude of the effect).
The linear regression is judged by the "R-squared", a measure of fit that is familiar to many people. The logistic regression is less well known, but it also has a standard measure of fit, the association of predicted probabilities and observed responses. The percentage of concordant pairs for our logistic models was very high (for example, it was 71.4 percent for the six-state combined model).
We can also measure the "Chi-square" value for the coefficient of the SSF term in each model to describe the significance of that term. Logistic regression models were calculated for the original six states, plus Ohio and New Mexico, which report rollover only if it is the first harmful event. In seven of the eight states, the "Chi-square" statistic for SSF is greater than for any of the other variables in the logistic model using individual variables. In the logistic model using scenario risk to combine all the variables except SSF, the "Chi-square" statistic for SSF is greater than that of the scenario risk variable in three of the eight states. This result also contradicts the Alliance's assertion that SSF is relegated to insignificance by the importance of road-use variables on the rollover experience of vehicles in use.
The Alliance's assertion that the effect of SSF on rollover is negligible was not a consequence of the possible superiority of logistic regression over linear, nor of the use of scenario risk rather than individual variables. Instead, the Alliance assertion depends upon a subtle change in the definition of the variables which serve as alternatives to SSF in explaining rollovers.
NHTSA used the number of police-reported single-vehicle crashes as a measure of each make/model's exposure to rollover risk. We did not include collisions with pedestrians or animals in the roadway in our definition of single-vehicle crashes because, while those crashes generate a police report, the collision itself poses no risk of rollover of the vehicle. Our sample size was large enough that we did not need to further investigate pedestrian and animal crashes for relevance. We did include collisions with parked vehicles because they represented a type of roadway departure and a collision with a fixed object, although these collisions offer the least exposure to typical tripping mechanisms.
Our analysis examined the effects of road-use variables because their correlations with SSF were the basis of an alternative theory of rollover causation. It is plausible that the greater rate of rollover of vehicles with low SSF is not caused by low SSF but rather by characteristics of drivers and roads which happen to be correlated with low SSF vehicles. The example of young males being the predominant driver population of particularly low SSF pickup trucks shows that this alternative has plausibility.
However, the Alliance departed from the road-use variables as alternative causes of rollover. The Alliance analysis was not an explanation of alternative theories of rollover causation but rather an attempt to show that there is little, if any, effect of SSF on rollover causation. To do this, the Alliance created a category of "non-vehicle" variables. This category allowed the addition of one variable whose effect overwhelmed the effects of all other variables. That variable was "first harmful event, collision with a traffic unit." It separated crashes which were collisions with pedestrians, animals or parked vehicles from other single-vehicle crashes. In essence, the extra variable separates crashes with minimum exposure to tripping mechanisms from all other single-vehicle crashes. This would seem to be a meaningless addition because there is no reason to expect a significant correlation between SSF and collisions with pedestrians, animals and parked vehicles. However, it sets up what the Alliance calls its "low risk scenario" which serves as a basis for comparison of rollover risk factors.
The Alliance then compared the effect on rollover risk of increased SSF to the effect on rollover risk made by moving from the scenarios of actual crashes to the "low risk scenario". The effect on rollover risk of moving actual crash scenarios to the "low risk scenario" is essentially the effect on rollover risk of eliminating tripping mechanisms. The effect is huge. In simplified terms, the Alliance has argued that the effect on tripped rollover gained by an increase of SSF is minimal compared to the effect on tripped rollover of removing tripping mechanisms. The statistical study in Appendix I includes a discussion of how this type of analysis, in which characteristics of the crash itself are used to define the risk scenarios, is equally useful for "demonstrating" that seat belts have negligible safety benefit.
We do not find the Alliance analysis persuasive. It may well be true that changing a single-vehicle run-off-the-road crash (where there is a high risk of rollover) into a crash in which the vehicle, for example, hits an animal in the road (where there is no risk of rollover) virtually eliminates the risk of rollover, and may do far more to minimize rollover risk than changing any single vehicle or driver factor. However, the point of this is unclear. One could also show that if vehicles could fly, there would be far fewer rollover crashes, based on the experience of actual aircraft. Since vehicles can not fly, and run-off-the-road crashes can not be changed into different types of crashes, positing these impossibilities as a means of analyzing, or addressing, the real world problem of more than 10,000 Americans dying each year in rollover crashes does not seem either helpful or insightful.
NHTSA seeks ways to address real world safety problems constructively. In the real world, driver and roadway factors are certainly important factors in all crashes, including rollovers. That is why NHTSA spends so much effort to increase belt use, reduce speeding, eliminate impaired driving, and so forth. However, the vehicle is also a significant factor in crash safety. If we take the driver and roadway conditions as givens (for example, a young male driver in a rural area), the physical attributes of different vehicles determine different outcomes when, for example, the vehicle drops two wheels off the road, and the driver responds incorrectly. Some vehicles will roll over much more often that others in these situations. Such vehicle differences have been shown to strongly correlate with rollover resistance expressed by SSF. We believe the American public should have this information available to consider when making purchase decisions.
B. NHTSA's Statistical Analysis Linking SSF to Rollover Rates
The Alliance commented that the method NHTSA used to analyze the statistical relationship between state crash data and SSF used in the RFC failed to take into account possible interactions between the various non-vehicle variables, and therefore underestimated the role of the non-vehicle factors in rollover risk. The possible interaction between alcohol involvement and the crash occurring on a curve in a particular crash was given as an example. The commenter suggested using logistic regression to resolve the problem of variable interaction.
As introduced in the previous section, Appendix I of this notice presents a new statistical study which adds another year of state crash data to the database relied on in our previous notice and contrasts analyses of the crash data using logistic regression of individual variables and risk scenarios to the linear regression method used in the previous notice. The model curves estimating rollovers per single-vehicle crash using logistic regression were nearly identical regardless of whether the road-use variables were entered individually or as combinations in risk
scenarios. However, logistic regression does produce a slightly different curve estimating rollovers per single-vehicle crash from that previously reported for linear regression.
Figure 1 shows the comparison between the updated linear regression analysis of the summarized data and the two logistic models (the six-state models using either the individual variables or the scenario-risk variable). The linear regression curve of the previous notice was essentially unchanged by the addition of another year of state crash data (for a total of 226,117 single-vehicle crashes with 45,574 rollovers). The logistic models are very similar to each other, and all the models indicate that the SSF is very important in understanding rollover risk. As noted previously, the average slope of the rollover risk vs. SSF curve estimated by the linear regression model in the range of observed data was -0.713, and the average slope of the corresponding curve of the logistic models is -0.598 or -0.580, depending on whether we use the individual variables or the scenario-risk variable. Also, logistic regression estimates a greater risk of rollover than does linear regression for vehicles with SSFs higher than 1.10.
The logistic regression and linear regression separate the effects of vehicle rollover resistance and those of road-use variables by different processes, and the logistic regression predicts a curve with a lower average slope. The Alliance commented that logistic regression considers the potential effect of variables in combination which may intensify or dilute their individual effects, but that linear regression would neglect combination effects. With this possibility in mind, we considered whether the use of the curve corresponding to logistic regression on individual variables would serve as a better basis of rollover risk for the vehicle star ratings than the linear regression curve proposed in our June 1, 2000 notice.
The proposed rating system was based on equal intervals of risk and positioned the five-star level at a value of SSF achievable by favorably designed family sedans. It also positioned the one-star range where it captured some popular SUVs and pickup trucks of the recent past. The manufacturers of the one-star vehicles generally have improved the current versions of the equivalent vehicles to the two-star level, but we believe the one-star rating ceiling would be stringent enough to discourage companies from returning to old design practices or from importing less advanced vehicles. A fortuitous feature of the ratings based on the linear regression curve was that reasonable one-star and five-star SSF boundaries occurred at predicted levels of rollover risk of 10 percent and 40 percent, permitting three equal intervals of risk between them divisible by ten for the two-star, three-star and four-star boundaries. Having the star rating intervals bounded at 10, 20, 30 and 40 percent rollover risk levels would make the meaning of the ratings easier to explain to consumers. Figure 2 presents the proposed rating system in graphical form. The updated linear regression curve in Figure 1 is nearly identical to the linear regression curve in Figure 2, except that it would set the one star boundary for 40 percent rollover risk at 1.03 instead of 1.04.
We considered the merits of the various ways in which the rollover risk versus SSF curve produced by logistic regression (Figure 1, Individual Variables) could be used to replace that produced by linear regression (also in Figure 1) as the basis for defining rollover risk in the rating system. If the proposed rating intervals in terms of SSF (1.04, 1.12, 1.24, 1.45) were maintained, they would no longer satisfy their rationale of representing equal increments of rollover risk in a single-vehicle crash. Conversely, if the risk intervals at 10, 20, 30 and 40 percent are maintained, the one-star SSF level would become 1.01 and the five-star level would become 1.51. A one-star level of 1.01 is so low that we know of only one vehicle (not in current production) that it would describe. Similarly, a five-star level of 1.51 appears to be out of reach for even the most stable family sedans which have demonstrated very good performance in resisting rollover. We believe that maintaining the 10, 20, 30 and 40 percent star boundaries with the logistic regression curve would have the practical effect of replacing the five-star rating system with a three-star rating system. At the low end of the SSF scale, the distinction between some historically poor performing vehicles and their improved replacements would be lost. At the higher end of the SSF scale, the distinction between some very good performing mid-sized and large sedans and some clearly poorer performing sub-compacts would be lost.
It would appear that the best way to incorporate the rollover risk levels estimated by logistic regression while maintaining the usefulness of the rating system to the consumer is to maintain the proposed one-star and five-star boundaries as closely as possible. This approach would require adjustment of the equal risk intervals between the one- and five-star boundaries to reflect the difference in average slope between the linear regression curve and the logistic regression curve. A five-star boundary of 1.46 corresponds to a rollover risk of less than 12 percent on the logistic regression curve. (The previous boundary of 1.45 would require a statement of risk of 12.1 percent which would not be desirable for consumer information). Similarly, a one-star boundary of 1.05 would correspond to a rollover risk greater than 36 percent. These one-star and five-star boundaries would allow for equal risk intervals of eight percentage points between the other star boundaries. A change from 10 percent risk intervals to eight percent risk intervals would be proportional to the difference in average slope between the linear regression curve and the logistic regression curve. Figure 3 illustrates this idea for using the logistic curve in a revised rating system in a graphical form comparable to Figure 2.
However, this idea also has serious drawbacks. It would move the three star level from 1.13 SSF to 1.17 and the four star level from 1.25 to 1.29 because the logistic regression shows less of the asymptotic shape of the raw data (Figure 1 of Appendix 1) than does the linear regression (of the log of SSF) curve previously proposed. This is troubling for two reasons. The shape of the original linear regression curve conforms better than does the logistic regression curve to the expectation that a given increase in SSF produces a substantially greater benefit for a vehicle with a low SSF than for one with a high SSF. Also, NHTSA believes that the proposed star rating levels may have become design goals for manufacturers seeking to improve rollover resistance. A change in star rating levels at this time may have the counterproductive effect of denying manufacturers recognition for substantial improvements in rollover resistance of vehicle designs.
While we do not deny the theoretical advantages of logistic regression cited by the Alliance regarding interactions between road use variables, the similarity in curves describing rollover risk as a function of SSF in the linear and logistic regression approaches suggests that such interactions do not exert a great influence on the effect of SSF. Therefore, we do not believe that the difference in risk analysis methods is great enough to compel a change in the proposed star rating levels to the detriment of manufacturers who are trying to achieve them and to the detriment of consumers who we believe will find the proposed rating system simpler. We also note that the linear regression curve presents a more conservative estimate of rollover risk for vehicles with SSF greater than 1.10, and we anticipate vehicles with SSF lower than 1.10 becoming rare in light of manufacturers' reported efforts at improving rollover resistance.
The rating system that NHTSA will use to define rollover risk and assign star rating is based on the updated linear regression curve in Figure 1 of this section. It would be described verbally as follows:
ONE STAR (): Risk of Rollover 40 percent or greater in a single-vehicle crash is associated
with SSF 1.03 or less.
TWO STARS (): Risk of Rollover 30 percent or greater but less than 40 percent is associated
with SSF 1.04 to 1.12.
THREE STARS (): Risk of Rollover 20 percent or greater but less than 30 percent is
associated with SSF 1.13 to 1.24.
FOUR STARS (): Risk of Rollover 10 percent or greater but less than 20 percent is
associated with SSF 1.25 to 1.44.
FIVE STARS (): Risk of Rollover less than 10 percent is associated with SSF 1.45 or
more.
C. Comments on Practical Problems with SSF Ratings
1. Difficulty of Improving Vehicles
The Alliance and the import manufacturers' organization, AIAM, asserted that improvements in a vehicle's SSF are not practicable since SSF is largely determined by its vehicle type. That is, the track widths and c.g. heights of pickups, SUVs, vans, and passenger cars are more or less fixed within certain limits. Significant changes to those measurements would simply eliminate the vehicle attributes which are common to the category and which are presumably desirable to consumers. These comments noted, for example, that significantly lowering the c.g. (thus raising the SSF) of an SUV could be accomplished by decreasing ground clearance, but doing so might make it unappealing compared to other vehicles in the SUV category. Conversely, the comments contended that marginal changes to track width and c.g. height small enough to maintain attributes in a vehicle category would not improve rollover risk. They conclude that SSF is not a useful design criterion, and it lacks the potential to reduce rollover rates if current vehicle types are to be preserved.
We disagree that significant improvement in SSF will necessarily eliminate desirable attributes within a class of vehicles. We are aware of a recent redesign of a production SUV(8) in the U.S. that achieved a decrease in c.g. height of approximately 2.0 inches (along with a significant increase in track width) while actually increasing the ground clearance. We estimate those changes represent an improvement in SSF equivalent to at least one star rating interval, and we would expect a significant decrease in rollover risk in single-vehicle crashes.
We also would note that passenger car-based SUV's with significantly better SSFs than traditional, truck-based SUVs have been gaining popularity in the absence of any consumer information program for rollover. The range of SSF among ten SUVs in our 1998 SSF measurements of a group of 32 then-new vehicles was equivalent to a rollover risk reduction of approximately 14 percent using the predictive curve from the linear regression analysis explained in this notice. So-called "crossover" vehicles promise even greater improvement. While these vehicles may offer less of some attributes of traditional SUVs, like overall ride height, the increasing popularity of crossover vehicles indicates that those attributes may be less important to consumers than the ones which they maintain in common with traditional SUVs, such as cargo room and traction on snowy roads. Thus, the suggestion that no changes to current vehicle designs are possible without significant customer resistance appears to be an assertion unsupported by what has happened recently in the market.
On the other hand, one of the models that scored highest among the ten SUVs in the 1998 measurements was a more or less traditional design, i.e., it was not passenger car-based.(9) This gives evidence that more stable light truck design is not incompatible with traditional design attributes.
The fact that SUVs are seldom used off-road indicates that not all SUV buyers really want off-road capability. Buyers who are aware of the tradeoff in risk of rollover that such off-road capability usually entails, may decide they can obtain the attributes they want or need in a more rollover-resistant vehicle. As a contrasting example, buyers who desire passenger and cargo capacity may choose a van or minivan over a conventional station wagon after deciding that their priorities outweigh the increase in rollover risk associated with that choice.
We believe that vehicle modifications to improve rollover resistance ratings are both achievable and beneficial. Press accounts suggest that manufacturers are, in fact, making such modifications as they redesign their light trucks. However, the ratings do not force manufacturers to modify vehicles, nor do they force consumers to accept only certain vehicle alternatives. The ratings will have a positive effect on the light vehicle rollover problem by making consumers more aware of trade offs in rollover stability, allowing consumers to make more informed purchase decisions, and influencing their awareness of the need to wear seat belts to prevent ejection in rollover crashes. This improvement will accrue even if the manufacturers make no changes to vehicles whatsoever in response to the program.
2. Possible Consequences of Improving SSF
Honda and the Alliance also suggested that, with a design criterion like a rollover rating based on SSF, manufacturers may be inclined to "design for the test." The manufacturer of a vehicle whose score falls just below a rating cutoff point might be able to make design adjustments that shift the vehicle's score into the next higher category. We believe there is no reason to discourage manufacturers from taking such actions because an improvement in SSF will result in a corresponding improvement in rollover risk. In fact, we believe that a major advantage of SSF, one that distinguishes it from other measures of rollover resistance, is that it "does no harm." Since SSF is a fundamental measure of inherent vehicle stability, there is no realistic risk that increasing SSF will degrade actual rollover rate or have other unintended, negative consequences. In contrast, improvement in other metrics can result in trade-offs that compromise overall safety. For example, maximizing a vehicle's Tilt Table Ratio can be accomplished by trading off some vehicle directional control (oversteer/understeer) characteristics. As another example, it is apparent that the Stability Margin metric can be improved by reducing tire grip, which could decrease driver control of the vehicle.(10) Furthermore, SSF is relevant to stability under virtually any circumstance, whether it be a run-off-the-road crash, an obstacle avoidance scenario, or even collisions with objects or other vehicles, though it is obviously more significant in some of those events, i.e., single-vehicle crashes, than in others, i.e., collisions, where impact forces can overwhelm other factors.
It was suggested in the comments that vehicle characteristics which an SSF-based rating ignores, like body shape and tire profile, influence rollover rate because they determine how a vehicle interacts with roadside objects and terrain during a crash event. As an example, Honda suggested that lowering a vehicle's c.g., thus improving its SSF, by equipping it with low-profile tires could increase the risk of tripped rollover by making sideward wheel contact with tripping mechanisms more likely. This is speculative and not persuasive. Each single-vehicle crash is, more or less, a unique event, because of the variety and complexity of circumstances involved. Although we agree that tripping usually initiates through interaction of a vehicle's wheels (i.e., tires and/or rims) with the roadway environment, generalizations about the influence of low-profile tires, or differences in body shape, on tripping frequency are extremely difficult to substantiate, given the limitless combinations of terrain, pavement condition, shoulder design, barriers, soil, vegetation, etc. A vehicle feature like taller, more flexible tire sidewalls may help avoid tripping in a few crashes, but is likely to be ineffective in the vast majority of others, and may be counterproductive in some cases. Even if it were possible for a manufacturer to identify tires and rims that were supposedly more resistant to tripping, safe handling and road holding considerations should certainly weigh more heavily in tire and rim selection.
A notable exception to this involves the problem of tire debeading. Clearly, a wheel rim that becomes exposed when a tire debeads either as a precursor to a single-vehicle crash or in the course of one, can become a primary tripping mechanism. We believe that tire and rim combinations that are more resistant to debeading may indeed lessen the risk of rollover in a single-vehicle crash. The agency is already planning to improve debeading requirements in FMVSS No. 109.
A further difficulty in identifying vehicle features that might improve tripping resistance is that crash data is limited. The minute level of detail required to thoroughly analyze the interaction of a vehicle's wheels, undercarriage, body components, etc., with the roadway environment in a run-off-the-road event is generally unavailable in state or national crash databases. NHTSA's NASS-CDS database does contain a high level of detail, but it focuses on a relatively small sampling of crashes. In contrast, the SSF of vehicles in crashes can be determined as long as the data contain a few details about the vehicle, like make and model. Availability of extensive crash data is important for analyses like NHTSA's statistical analysis of crashes in six U.S. states as reported in the RFC and in Appendix I here.
Honda also suggested that problematic suspension behavior such as "suspension-jacking" can lead to a higher risk of rollover regardless of SSF, and that this exemplifies why SSF alone is not an adequate indicator of rollover resistance. Although vehicles with particular suspensions, most notably "swing-axle" designs, historically may have been associated with rollover, we believe those represent relatively few cases out of a very large population of rollover crashes and that such examples of suspension design are uncommon in current vehicles. Furthermore, suspension behavior is less important than SSF once a vehicle has left the roadway, where factors like shoulder condition and terrain interact with the basic stability characteristics of the vehicle to determine crash outcome.
3. SSF Measurement Accuracy
Honda stated in response to the RFC that the Vehicle Inertia Measurement Facility (VIMF) that NHTSA will use to ascertain SSF is not accurate enough to repeatably give useful vehicle ratings. Honda suggested that for c.g. height measurement the measurement error is the sum of 0.5 percent "repeatability" error and 0.5 percent "accuracy" error, giving a total measurement error of �1.0 percent of the measured value. Honda believes an error of that magnitude is significant, compared to the small differences between vehicles being compared, and that a vehicle could be assigned an incorrect number of stars due to measurement error.
Honda appears to have misinterpreted the published reports available on the VIMF. The document cited in Footnote 19 of the RFC does indicate, in Table 1, "error bounds" for c.g. height of �0.5 percent of the measured value.(11) Other documents(12), (13), (14) describing the design of the VIMF give the same value for "repeatability" or "two standard deviation error" for c.g. height measurements.
Basically, "repeatability," as used in the referenced documents in regard to the VIMF, is not separate from the "accuracy" of the system. It is incorrect to assume that the total VIMF system error in c.g. height measurements is the sum of the 0.5 percent repeatability and 0.5 percent accuracy, for a total system error of one percent in c.g. height measurements. The total system error of the VIMF for c.g. height measurement is 0.5 percent or less, as explained below.
When the VIMF was under development, an error analysis was conducted based on experience with NHTSA's Inertial Parameter Measurement Device (IPMD), a precursor to the VIMF. Over the course of several years, the IPMD underwent successive updates and improvements, culminating in a fifth and final version of the machine that ultimately served as a model for the VIMF. The error analysis accounted for all the known sources of error arising from each system component, for example, platform deflection and vehicle restraint rigidity, as experience with the IPMD had indicated. By mathematical modeling, the contribution of each component to the whole system error was determined. The final design specifications for the VIMF were set by that analysis. Each component was selected or fabricated so as to limit the combined error from all the known contributions to 0.5 percent of the measured value for c.g. height. The details of the error analysis are discussed in the referenced documents.
Since it was designed and constructed, the accuracy of the VIMF has been evaluated using a custom-built calibration fixture with a known c.g. location. This fixture is a heavy weldment made from stock steel plates and box section beams whose individual c.g. locations are easily determined by geometry. Because it is a very rigid body and is fabricated from such geometrically simple components, the calibration fixture's c.g. location, as well as its mass moments of inertia, are known theoretically, and it is thus a benchmark for reckoning the accuracy of the VIMF. The calibration fixture can be set up in either a light or heavy configuration, the latter achieved by adding weight in precise locations to increase the c.g. height by a known amount. In the light configuration, the fixture is representative of the mass and c.g. height of a mid-size passenger car. In the heavy configuration, it is representative of a light truck.
In calibration tests using this fixture, the VIMF consistently measures the c.g. location to within 0.5 percent of the known value. Tables 6 and 7 of the 1995 Heydinger paper cited here indicate that the VIMF was able to measure the c.g. height of the fixture to within 0.46 percent (2.6 mm in 561.2 mm) and 0.32 percent (2.6 mm in 809.2 mm) of its theoretically known values in the light and heavy configurations, respectively. Those results correspond well with the VIMF error analysis which predicts that the degree of accuracy should be somewhat higher when measuring heavier, higher c.g. vehicles. That is, the measurement accuracy for vehicles which are likely to fall into the lower SSF categories is significantly better than 0.5 percent.
While we believe the NHTSA measurements will be sufficiently accurate, no degree of measurement accuracy can prevent borderline cases. There is always a possibility of a vehicle score falling so close to a cutoff point between star ranges that applying even a small amount of measurement uncertainty to the score results in ambiguity about the category to which the vehicle belongs. This situation is characteristic of any rating scheme and is no different from what currently exists in the NHTSA frontal and side NCAP. We plan to use conventional rounding methodology to determine the SSF of each test vehicle to two decimal places and assign stars based on that result.
If a manufacturer determined that one of its models was on the border between star levels, the manufacturer could, if it wished, make changes to the vehicle to improve its SSF to the point where it falls comfortably in the higher category. If the vehicle was indeed on the border, the changes necessary would probably be very minor, and it would be voluntary, not mandatory.
D. Consumers' Ability to Understand SSF as a Measure of Rollover Risk in the Event of a Single-vehicle Crash
Some commenters had misgivings about consumers' abilities to understand and use the new rollover rating information in three areas. They believe:
Each of these areas are discussed and responded to below.
1. Are Consumers Capable of Understanding That the Star Rating Describes the Risk of Rollover in the Event That the Vehicle Is Involved in a Single-vehicle Crash?
Auto manufacturers and the National Automobile Dealers' Association (NADA) believe that consumers are not capable of understanding that the star rating describes the risk of rollover in the event that the vehicle is involved in a single-vehicle crash. The following is a list of comments and the commenters who made them:
The language that will be used in consumer information products concerning this rollover rating (see Section IV) was developed using the outcome of focus group testing. As discussed in the June 2000 notice, in April 1999 NHTSA conducted a series of six focus groups to examine ways of presenting comparative rollover information. As a result of the comments to our June 2000 notice, NHTSA conducted another series of focus groups in November 2000. Two versions of explanatory language were presented to a total of 12 groups of nine consumers each in two different cities. NHTSA asked the focus groups to evaluate a short version of rollover rating explanatory language that read as follows:
Most rollover crashes occur when a vehicle runs off the road and is tripped by a ditch, soft soil, a curb or other object causing it to roll over. These are called single-vehicle crashes because the crash did not involve a crash with another vehicle. The Rollover Rating is an estimate of your risk of rolling over if you have a single-vehicle crash. The Rollover Rating essentially measures how "top-heavy" a vehicle is. The more "top-heavy" the vehicle, the more likely it is to roll over. The lowest rated vehicles (1-star) are at least 4 times more likely to roll over than the highest rated vehicles (5-stars).
In A Single-vehicle Crash, a vehicle with a rating of:
Five Stars - Has a risk of rollover of less than 10%
Four Stars - Has a risk of rollover greater than 10% but less than 20%
Three Stars - Has a risk of rollover greater than 20% but less than 30%
Two Stars - Has a risk of rollover greater than 30% but less than 40%
One Star - Has a risk of rollover greater than 40%
We also asked the focus groups to evaluate the following longer version:
In A Single-vehicle Crash, a vehicle with a rating of:
Five Stars - Has a risk of rollover of less than 10%
Four Stars - Has a risk of rollover greater than 10% but less than 20%
Three Stars - Has a risk of rollover greater than 20% but less than 30%
Two Stars - Has a risk of rollover greater than 30% but less than 40%
One Star - Has a risk of rollover greater than 40%
The focus group testing pointed out areas of difficulty in comprehension that were addressed in writing the final language.
Focus group participants felt that while the shorter explanation was too short to fully comprehend the rating, the longer version was overwhelming and included unnecessary information. Based on the focus group inputs, we have developed the following language:
Description of Rollover Resistance Rating
In A Single-Vehicle Crash, a vehicle with a rating of:
Five Stars - Has a risk of rollover of less than 10%
Four Stars - Has a risk of rollover between 10% and 20%
Three Stars - Has a risk of rollover between 20% and 30%
Two Stars - Has a risk of rollover between 30% and 40%
One Star - Has a risk of rollover greater than 40%
The length of the final version is midway between the two versions tested. It adds information not included in the tested short version that participants felt was particularly important in understanding the information and/or particularly compelling to cause them to pay attention to the information. It deletes information in the tested long version that participants felt was unnecessary and/or confusing. In addition, the explanation of the star ratings was simplified because the original format seemed to cause some confusion about whether more stars or less stars was a better rating. Finally, NHTSA has chosen to use the term "Rollover Resistance Rating" rather than "Rollover Rating" as this seemed to help participants understand the rating.
The potential confusions cited by the commenters did not occur in the focus groups. From the discussions during the focus groups, it is clear that participants are aware that rollover is heavily influenced by driver and road characteristics. In almost all groups the first cause of rollover cited by participants was speed. Participants also mentioned road conditions and driver behavior and/or experience as factors. However, the participants also seemed to understand that the vehicle can also play a part in determining whether or not a rollover occurs, and that this rating was only a measure of that factor.
NHTSA notes that the explanatory language will be used in the Buying a Safer Car brochure, and other places that present the star ratings. This brochure's primary focus is how a person can purchase a safer vehicle. It does not include extensive discussion of driver behaviors that can increase safety, as those types of issues tend to be addressed by other agency programs. NHTSA will include additional information about rollover in the form of Q&A's on the agency's website, and is considering developing additional rollover consumer information, both of which would be more appropriate places for discussion of other factors that can reduce the risk of rollover.
2. Will Consumers Find the Information Useful in Making a Vehicle Choice?
The commenters listed below believe that even if consumers do understand the risk represented by the stars, this information will not be useful to them in choosing a vehicle. They assert the following:
While it is true that many consumers limit their vehicle choices early in the purchase-decision process (e.g., must be an SUV), many others are also considering vehicles in more than one class (e.g., a van or an SUV). As the availability of rollover resistance rating information becomes more widely known, consumers will begin to know that certain types of vehicles have better ratings than others. In addition, while we cannot predict the final spread of ratings for the 2001 models that will be tested, in our research there was usually a two- to three-star rating range for each class. Thus, by his or her vehicle choice alone, a consumer could reduce his or her chance of a rollover in a single-vehicle crash by up to 24% in some cases.
In addition, another safety benefit of the NCAP program is the general improvements manufacturers have made to vehicles as the result of publishing such ratings. These improvements benefit all consumers regardless of their choice of vehicle. Over the years, manufacturers have responded to the frontal NCAP program and as a result the number of models achieving a five-star rating today is 2.7 times what it was when the program started in 1979. As for the criticism that star ratings do not indicate the tiny difference among vehicles near the dividing lines, this is also true for the frontal and side NCAP ratings. Just as with these ratings, the actual scores for the vehicles will be available on the NCAP website to anyone who is interested.
Finally, with regard to comments that options can cause wide difference in the rating for a specific model, over the years that we have been researching vehicle inertial parameters, four-wheel drive is the only equipment option for which we have observed a large potential effect on SSF. NHTSA intends to test the most common versions of all vehicles. Where two- and four-wheel drive versions of the same vehicle are available, we will test them both and report them as separate models. We will accurately describe the actual test vehicle in the literature reporting the rating.
Manufacturers who believe there are significant differences in SSF for different vehicle configurations may fund an optional NCAP measurement, just as they may fund optional frontal or side NCAP tests. Then if the difference in equipment or configuration makes a difference in the SSF, that difference will be available to the public.
3. Even If Consumers Use the Information, Will the New Program Lead to a Decrease in Rollover Crashes?
Some commenters believe that even if consumers do use the new ratings, the outcome of that use will be other than what we desire. The following are comments and who made them.
The best indicator of the potential benefits of any new ratings program is the frontal NCAP program. As discussed previously, there are now many more five-star vehicles than when the frontal NCAP program started. Research also indicates that a five-star rating correlates to enhanced real-world safety. Therefore, all consumers benefit from these improvements in the vehicle fleet even if they don't make purchase decisions based on the star ratings. Both of these types of analysis will be possible for side impact and rollover NCAP after an adequate number of years of experience. There is no evidence that consumers have responded to vehicles with high frontal NCAP scores or other safety features by riskier driving behavior, and no reason to believe that they will respond differently to rollover ratings. Similarly, there is no indication that consumers believe they are immune to injury by driving a vehicle with a five-star frontal or side NCAP rating or with additional safety features.
NHTSA disagrees that cars are less safe than light trucks. Occupant fatality rates (average 1991-98, FARS data) across all crash types indicates that large cars have a lower fatality rate than SUV's and small pickup trucks, and the same as the rate for standard pickups. Medium cars have a rate about the same as SUV's and lower than the rate for small pickup trucks. Small cars and small pickup trucks have about the same rate. See Figure 4. If we narrow the picture to rollover crashes, as in Figure 5, we see that SUV's and small pickups have the highest rates, at least 75 percent higher than the rate for small cars. The rates for medium and large cars are below any of the light truck types.
However, NHTSA is aware that as we expand the areas in which we provide consumer information ratings, it is becoming more and more important to provide consumers with guidance on how to weigh ratings in different categories. For example, it is quite common for SUVs to receive five-star ratings in side impact NCAP, but our research indicates that these vehicles will have rollover ratings in the one- to three-star range. NHTSA can help consumers understand these differences by providing them with information on the frequency of various crash types, as we have been doing with the front and side impact NCAP ratings, and we plan to do for rollover crashes. In addition, NHTSA has been considering possible ways to provide consumers with a single summary rating of a vehicle's safety.
E. The Question of Electronic Stability Control
Continental Teves objected to the use of SSF to rate rollover resistance because the ratings would not reward manufacturers for equipping vehicles with Electronic Stability Control (ESC). It was also dissatisfied with language in the notice promising consumer information about ESC as part of the rating presentation after there is some evidence of its effectiveness. BMW, Toyota, Isuzu, Tenneco and the Alliance offered similar comments. All expressed confidence that the technology would reduce the number of on-road loss-of-control situations that often result in off-road tripped rollovers. The Alliance suggested that ESC may also reduce the risk of untripped rollover, and Continental believes that it may help drivers regain control after they leave the roadway. Many commented that ratings based on SSF would stifle and undercut advanced vehicle technology. The notice specifically asked commenters to share any data they may have on the effectiveness of stability control technologies in preventing single-vehicle crashes, but none did so.
The NCAP program rates the risk of rollover in the event of a single-vehicle crash. Most of these single-vehicle crashes involve hitting a curb or running off the road accidently and encountering soft soil, a ditch or something that trips the vehicle. To repeat, 95 percent of rollovers are tripped. Once a vehicle is in this situation and strikes a tripping mechanism, its chances of rolling over depend heavily on its SSF.
The promise of ESC is not that it can change what happens when a vehicle hits a tripping mechanism but that it may help the driver to avoid going off the roadway in the first place. ESC can apply one or more brakes automatically to keep the yaw rate of the vehicle proportional to its speed and lateral acceleration. Essentially, it corrects for vehicle understeer or oversteer, and some systems may override a driver's failure to brake when in fear of losing control. This benefit could minimize the driver's chances of compounding his or her driving errors in a panic situation. However, it cannot keep a vehicle from leaving the roadway if the vehicle is going too fast for the maneuver the driver is attempting.
Like frontal and side NCAP ratings, the Rollover Resistance Rating is concerned with vehicle attributes that affect the outcome of a crash. None of the present ratings attempt to describe the probability of a vehicle's involvement in a crash. For example, the frontal crashworthiness star rating does not reward manufacturers who equip vehicles with advanced braking systems. Also, the agency cannot rely on skid pad demonstrations to determine the effectiveness of a safety device in the hands of the public. Anti-lock brakes were once considered likely to reduce rollover crashes because they had the potential to reduce the number of vehicles exiting the road sideways as a result of rear brake lock-up. This expectation has not been realized in passenger cars according to years of crash statistics. There has actually been an increase in the rollover rate of passenger cars equipped with anti-lock brakes that researchers have not yet been able to explain.
The commenters suggest that NHTSA should abandon SSF as a basis for rollover rating because it does not reward ESC in the star rating and that without such a reward the use of the technology would be in doubt. The importance of SSF to rollover resistance is supported by abundant real-world evidence, while there is no data on the effectiveness of ESC. Based on the relative data available, it would not be appropriate to abandon SSF. We encourage manufacturers to assist us in determining the effectiveness of ESC by identifying optional ESC systems in VIN codes and sharing available data. We will continually monitor data on the real-world effectiveness of ESC and make appropriate changes based on that data. We do not expect that manufacturers will abandon ESC, since they express so much confidence in its ultimate effectiveness.
NHTSA wants to encourage technological applications that enhance vehicle stability, provide drivers with more control of their vehicle, and help prevent rollover and other crashes. For ESC in particular, it is reasonable to assume that it will help some drivers use the available traction to stay on the road in circumstances that would otherwise result in panic-driven errors and roadway departure. We have asked the National Academy of Sciences to recommend ways of combining the effect of ESC on exposure to single-vehicle crashes, with the effect of SSF on rollover resistance in a single-vehicle crash, as part of its Congressionally-mandated study of rollover consumer information. We do not expect that a recommendation can be implemented without some determination of ESC's real-world effectiveness, but in the meantime we will identify in our Buying a Safer Car brochure the vehicles for which ESC is available and provide an explanation of these systems. The identification of vehicles with ESC will start in the December 2000 issue of Buying a Safer Car. The April 2001 issue of Buying a Safer Car will also present Rollover Resistance Ratings.
The first presentation of Rollover Resistance Ratings will be on the NHTSA website. The website will also present Questions and Answers regarding rollover crashes including one discussing the effect of ESC and its relationship to the Rollover Resistance Ratings. Until the Rollover Resistance Ratings are integrated into Buying a Safer Car, the NHTSA website will provide a chart of rated vehicles which will include a column indicating the availability of ESC. The heading of that column will provide a link to the Q&A about ESC.
The Q&A section will include the following discussion:
Question: How does Electronic Stability Control affect rollover, and what is its relationship to the Rollover Resistance Ratings?
Answer: Most rollovers occur when a vehicle runs off the road and strikes a curb, soft shoulder, guard rail or other object that "trips" it. The Rollover Resistance Ratings estimate the risk of rollover in event of a single vehicle crash, usually when the vehicle runs off the road. Electronic Stability Control (which is offered under various trade names) is designed to assist drivers in maintaining control of their vehicles during extreme steering maneuvers. It senses when a vehicle is starting to spin out (oversteer) or plow out (understeer), and it turns the vehicle to the appropriate heading by automatically applying the brake at one or more wheels. Some systems also automatically slow the vehicle with further brake and throttle intervention. What makes Electronic Stability Control promising is the possibility that with its aid many drivers will avoid running off the road and having a single vehicle crash in first place. However, ESC cannot keep a vehicle on the road if its speed is simply too great for the available traction and the maneuver the driver is attempting or if road departure is a result of driver inattention. In these cases, a single vehicle crash will happen, and the Rollover Resistance Rating will apply as it does to all vehicles in the event of a single vehicle crash.
A similar discussion will accompany the rollover resistance ratings in the April issue of Buying a Safer Car.
F. Alternative Programs for Rollover Consumer Information Suggested by Commenters
Three commenters to the RFC presented ideas for consumer information programs to be used in place of the agency's proposal to use SSF to rate vehicles. The Alliance had four suggestions:
Ford and Suzuki commented that SSF should be used only to rate vehicle classes and should not be used to show distinctions between make/models in the same class. These commenters also believe that the program should not present the risk of rollover quantitatively.
The NADA recommended that NHTSA put more emphasis on the seat belt message in the context of rollover, including child safety restraints and suggested that manufacturers include in their vehicles' owners manuals material about crash avoidance driving practices. The manufacturers' association, the Alliance, on the other hand, wanted to see seat belt information only in a general sense, not specifically referring to rollover.
The major flaw with all of these suggestions is that they do not deliver what the consumer wants - definitive, comparative, information about the relative risk of rollover in specific vehicles. We have shown, in the previous sections of this notice and the notices that have preceded it, that we can link rollover risk to the SSF of specific make/models. Any rollover-specific consumer information product that NHTSA develops in the future will mention driving habits that contribute to rollover prevention and emphasize the importance of seat belt use. However, the focus of the present action is on allowing consumers to make an informed choice about the safety of the vehicles they purchase, both by class and by model.
G. Commenters Preference for a Minimum Standard Based on a Dynamic Test
Tab Turner, a plantiff's attorney, and Insurance Institute for Highway Safety, Consumers Union, and Advocates for Highway and Auto Safety, stated in their comments that, while they had no objection to using SSF to provide consumer information, an information program was not sufficient to address the rollover problem. They believe a federal motor vehicle safety standard, based on a dynamic track test of vehicles, is needed.
Notwithstanding the recent Transportation Recall Enhancement, Accountability, and Documentation (TREAD) Act(15) which requires the agency to issue ratings based on a dynamic test within two years, we believe that consumer information based on SSF is an appropriate way to proceed at this time to address rollover. Two issues are involved here: the issue of a minimum standard versus consumer information, and the issue of dynamic testing versus a static metric. Both of these issues were addressed at length in the RFC.
We agree that it would be desirable to have a standard to address a safety issue as significant as rollover resistance. However, as explained in the RFC, NHTSA previously decided not to set a vehicle rollover standard at a level that would effectively force nearly all light trucks to be redesigned to be more like passenger cars.(16) NHTSA also previously decided not to set a vehicle rollover standard at a level that would effectively force a redesign even of certain vehicle types like small pickups and small SUVs(17) because it would not be appropriate to prohibit the manufacture and sale of those vehicles without some predictable benefit commensurate with the cost of that action. However, we can still provide accurate and meaningful information about rollover resistance to allow the public to make fully informed choices when selecting a new vehicle.
IV. Rollover Information Dissemination using SSF in NCAP
The agency has decided to go forward with a pilot consumer information program on vehicle rollover resistance, using the SSF as a basis for the rating system. This program will be part of NCAP, which currently gives consumers information on frontal and side-impact crashworthiness. Today we are announcing the 2001 model year vehicles to be tested and how the information will be disseminated to the public.
There are two activities ongoing in NHTSA that may change this pilot program: the study by the National Academy of Science mandated by Congress in the Department's Fiscal Year 2001 appropriations bill(18) and the Congressional requirement contained in the TREAD Act that the agency develop a dynamic test for consumer information on rollover, conduct the tests, and determine how best to disseminate the test results to the public by November 1, 2002. Changes or additions to this program will be developed if necessary to conform to the requirements of these two statutes.
The rollover information program will operate just as the current frontal and side NCAP does. New models are selected for testing before the beginning of the model year. Selection is based primarily on production levels predicted by the manufacturers and submitted to the agency confidentially. Consideration is given also to vehicles scheduled for major changes, or new models with specific features that may affect their SSF's. The vehicles chosen for NCAP testing will be obtained and measured by NHTSA, as the vehicles become available. Vehicles are obtained with popular equipment, typical of a rental fleet, and the equipment with possible influence on SSF will be included in the vehicle description when the rating is reported. Two-wheel drive and four-wheel drive versions of a vehicle are treated as separate models, because a four-wheel drive option can have a significant effect on SSF. As provided for in the frontal and side NCAP, manufacturers can, at their option, pay for tests of vehicles, models, or configurations not included in NHTSA's test plan, if they wish to inform consumers about those vehicles through the program.(19) The SSF will be converted to a star rating according to the curve presented in Section III and Appendix I at the intervals specified in Section III. The rollover rating information will be available on the agency's website, and will be included in all NHTSA publications and press releases which use NCAP data. The brochures and the website presentation will explain the basis of the ratings, present the SSF measurements, and discuss the magnitude of rollover harm prevention provided by seat belt use.
As part of the presentation on rollover the following explanatory text will be used:
Description of Rollover Resistance Rating
In A Single-Vehicle Crash, a vehicle with a rating of:
Five Stars - Has a risk of rollover of less than 10%
Four Stars - Has a risk of rollover between 10% and 20%
Three Stars - Has a risk of rollover between 20% and 30%
Two Stars - Has a risk of rollover between 30% and 40%
One Star -
Has a risk of rollover greater than 40%
As part of these ratings, the agency also has decided to note vehicles that are equipped with "electronic stability control" technology, which may reduce the risk of a vehicle getting into an incipient rollover situation.
Appendix II contains a preliminary list of vehicles we will measure and for which we will report SSF and star ratings. The vehicles will be tested as they become available to the test facility. As of today 24 vehicles have been tested; the results are available from the Auto Safety Hotline (888-327-4236) or on the NHTSA website at www.nhtsa.dot.gov. The remainder of the test results and star ratings for the 2001 model year will be available by April 30, 2001.
V. Rulemaking Analyses and Notices
Executive Order 12866
This notice was not reviewed under Executive Order 12866 (Regulatory Planning and Review). NHTSA has analyzed the impact of this decision and determined that it is not a "significant regulatory action" within the meaning of Executive Order 12866. The agency anticipates that providing information on rollover risk under NHTSA's New Car Assessment Program would impose no regulatory costs on the industry.
Authority: 49 U.S.C. 322, 30117, and 32302; delegation of authority is at 49 CFR 1.50 and 49 CFR 501.8.
Issued on:
Stephen R. Kratzke
Associate Administrator for
Safety Performance Standards
BILLING CODE: 4910-59P