[Code of Federal Regulations] [Title 49, Volume 4] [Revised as of October 1, 2002] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR213.113] [Page 105-108] TITLE 49--TRANSPORTATION CHAPTER II--FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 213--TRACK SAFETY STANDARDS--Table of Contents Subpart D--Track Structure Sec. 213.113 Defective rails. (a) When an owner of track to which this part applies learns, through inspection or otherwise, that a rail in that track contains any of the defects listed in the following table, a person designated under Sec. 213.7 shall determine whether or not the track may continue in use. If he determines that the track may continue in use, operation over the defective rail is not permitted until-- (1) The rail is replaced; or (2) The remedial action prescribed in the table is initiated. [[Page 106]] [GRAPHIC] [TIFF OMITTED] TN28SE98.059 Notes A. Assign person designated under Sec. 213.7 to visually supervise each operation over defective rail. A2. Assign person designated under Sec. 213.7 to make visual inspection. After a visual inspection, that person may authorize operation to continue without continuous visual [[Page 107]] supervision at a maximum of 10 m.p.h. for up to 24 hours prior to another such visual inspection or replacement or repair of the rail. B. Limit operating speed over defective rail to that as authorized by a person designated under Sec. 213.7(a), who has at least one year of supervisory experience in railroad track maintenance. The operating speed cannot be over 30 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. C. Apply joint bars bolted only through the outermost holes to defect within 20 days after it is determined to continue the track in use. In the case of Classes 3 through 5 track, limit operating speed over defective rail to 30 m.p.h. until joint bars are applied; thereafter, limit speed to 50 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. When a search for internal rail defects is conducted under Sec. 213.237, and defects are discovered in Classes 3 through 5 which require remedial action C, the operating speed shall be limited to 50 m.p.h., or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower, for a period not to exceed 4 days. If the defective rail has not been removed from the track or a permanent repair made within 4 days of the discovery, limit operating speed over the defective rail to 30 m.p.h. until joint bars are applied; thereafter, limit speed to 50 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. D. Apply joint bars bolted only through the outermost holes to defect within 10 days after it is determined to continue the track in use. In the case of Classes 3 through 5 track, limit operating speed over the defective rail to 30 m.p.h. or less as authorized by a person designated under Sec. 213.7(a), who has at least one year of supervisory experience in railroad track maintenance, until joint bars are applied; thereafter, limit speed to 50 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. E. Apply joint bars to defect and bolt in accordance with Sec. 213.121(d) and (e). F. Inspect rail 90 days after it is determined to continue the track in use. G. Inspect rail 30 days after it is determined to continue the track in use. H. Limit operating speed over defective rail to 50 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. I. Limit operating speed over defective rail to 30 m.p.h. or the maximum allowable speed under Sec. 213.9 for the class of track concerned, whichever is lower. (b) As used in this section-- (1) Transverse fissure means a progressive crosswise fracture starting from a crystalline center or nucleus inside the head from which it spreads outward as a smooth, bright, or dark, round or oval surface substantially at a right angle to the length of the rail. The distinguishing features of a transverse fissure from other types of fractures or defects are the crystalline center or nucleus and the nearly smooth surface of the development which surrounds it. (2) Compound fissure means a progressive fracture originating in a horizontal split head which turns up or down in the head of the rail as a smooth, bright, or dark surface progressing until substantially at a right angle to the length of the rail. Compound fissures require examination of both faces of the fracture to locate the horizontal split head from which they originate. (3) Horizontal split head means a horizontal progressive defect originating inside of the rail head, usually one-quarter inch or more below the running surface and progressing horizontally in all directions, and generally accompanied by a flat spot on the running surface. The defect appears as a crack lengthwise of the rail when it reaches the side of the rail head. (4) Vertical split head means a vertical split through or near the middle of the head, and extending into or through it. A crack or rust streak may show under the head close to the web or pieces may be split off the side of the head. (5) Split web means a lengthwise crack along the side of the web and extending into or through it. (6) Piped rail means a vertical split in a rail, usually in the web, due to failure of the shrinkage cavity in the ingot to unite in rolling. (7) Broken base means any break in the base of the rail. (8) Detail fracture means a progressive fracture originating at or near the surface of the rail head. These fractures should not be confused with transverse fissures, compound fissures, or other defects which have internal origins. Detail fractures may arise from shelly spots, head checks, or flaking. (9) Engine burn fracture means a progressive fracture originating in spots where driving wheels have slipped on top of the rail head. In developing downward they frequently resemble the [[Page 108]] compound or even transverse fissures with which they should not be confused or classified. (10) Ordinary break means a partial or complete break in which there is no sign of a fissure, and in which none of the other defects described in this paragraph (b) are found. (11) Damaged rail means any rail broken or injured by wrecks, broken, flat, or unbalanced wheels, slipping, or similar causes. (12) Flattened rail means a short length of rail, not at a joint, which has flattened out across the width of the rail head to a depth of \3/8\ inch or more below the rest of the rail. Flattened rail occurrences have no repetitive regularity and thus do not include corrugations, and have no apparent localized cause such as a weld or engine burn. Their individual length is relatively short, as compared to a condition such as head flow on the low rail of curves. (13) Bolt hole crack means a crack across the web, originating from a bolt hole, and progressing on a path either inclined upward toward the rail head or inclined downward toward the base. Fully developed bolt hole cracks may continue horizontally along the head/web or base/web fillet, or they may progress into and through the head or base to separate a piece of the rail end from the rail. Multiple cracks occurring in one rail end are considered to be a single defect. However, bolt hole cracks occurring in adjacent rail ends within the same joint must be reported as separate defects. (14) Defective weld means a field or plant weld containing any discontinuities or pockets, exceeding 5 percent of the rail head area individually or 10 percent in the aggregate, oriented in or near the transverse plane, due to incomplete penetration of the weld metal between the rail ends, lack of fusion between weld and rail end metal, entrainment of slag or sand, under-bead or other shrinkage cracking, or fatigue cracking. Weld defects may originate in the rail head, web, or base, and in some cases, cracks may progress from the defect into either or both adjoining rail ends. (15) Head and web separation means a progressive fracture, longitudinally separating the head from the web of the rail at the head fillet area. [63 FR 34029, June 22, 1998; 63 FR 51639, Sept. 28, 1998]