FSC 7530 JCP G65
RECYCLED 25% OPACIFIED BOND WHITE AND COLORED
Bond Paper May 1, 1997
(50% recovered material w/30% PC)
--------------------------------------------------------------------------
Use information: This paragraph is informational only and is not
exclusively definitive of the end use.
For high quality face and back offset printing of stationery, open
forms, etc.; requiring processing through high speed copiers and laser
printers with imaging on both face and back; requiring execution with
pen and ink, erasing quality, and greater opacity than obtainable in
Standard JCP G40/G45. May contain some foreign or ``dirt'' particles
embedded in the surface of the paper. Printed matter may include text
and line illustrations.
Unless the option below is specified, the following `basic'
specification applies.
Stock: Not less than 25 pct cotton or linen fibers. Groundwood pulp, not
to exceed 1 pct; the remainder chemical pulp.
Note: \1\ Not less than 50 pct total recovered material of which 30
percentage points shall be postconsumer recovered fiber. Postconsumer
fiber, in any percent over 30 percentage points, is encouraged,
provided that the requirements of this Standard are met.
Grammage (g/m \2\)................................ 90
Basis weight: 17 by 22 inches, 500 sheets
(pounds).......................................... 24
A tolerance of 5 pct shall be
allowed.
Folding endurance: Average each direction, not less than--
M.I.T. (double folds)........................... 20
Schopper (double folds)......................... 30
Opacity: Average, not less than (percent)......... 90
No individual specimen shall average less than
(percent)....................................... 88
Smoothness: Average, each side, not to exceed
(units)........................................... 270
Any specimen averaging more than 270 units shall be sufficient cause
for rejection of the paper.
Ruling and writing qualities: Lines ruled and characters written with
pen and ink shall be clear cut and free from excessive feathering.
Erasing quality: Paper shall retain good ruling, writing, and typing
quality, texture, and surface appearance, without ink spreading after
repeated erasures. Samples from the delivery shall show no greater
resistance than the standard sample to removal by abrasion of
typewritten characters.
Curl: Paper shall lie flat before and after processing through a high
speed copier or laser printer with either no tendency to curl or with
a curl which can be overcome under reasonable working conditions.
General appearance: Paper shall conform to the standard sample(s)
adopted by the Government.
Color: The paper in the order (or publication) shall be uniform with a
target brightness of 82 pct for the white paper. The color variation
shall not exceed DE(CIELAB)=1.0.
For colored stock, paper shall match one of the established
standards or specified by the ordering agency. Color shall not fade or
transfer (rub off) and shall appear even and uniform on the surface of
the sheet stock shall not be 2-sided. Color coordinates for selected
standards are included in Part 3.
Formation: Shall be uniform.
Cleanliness: The dirt count for each side of the paper shall not
exceed 650 specks per square meter. No sample sheet (600 to 650 cm\2\
in size) shall contain more than one defect with an equivalent area of
0.25 mm\2\ or greater.
Sampling and testing: Shall be conducted in accordance with standards in
Part 2, Government Paper Specification Standards.
OPTION
Option A: Alkaline paper. This option is for products requiring above
average permanence and for white stock only.
The following requirements replace the same in the `basic'
specification and are added to the specification.
Stock; Not less than 25 pct cotton or linen fibers; the remainder
bleached chemical woodpulp.
Note:\1\ Not less than 50 pct total recovered material of which 30
percentage points shall be postconsumer recovered fiber. Postconsumer
fiber, in any percent over 30 percentage points, is encouraged,
provided that the requirements of this Standard are met.
Acidity: pH value, by cold extraction of the white stock shall be not
less than 7.0. The paper shall contain not less than 2 pct calcium
carbonate.
Any deviation in this requirement shall be sufficient cause for
rejection of the paper.
Cleanliness: The dirt count for each side of the paper shall not exceed
250 specks per square meter. No sample sheet (600 to 650 cm\2\ in
size) shall contain more than one defect with an equivalent area of
0.25 mm\2\ or greater.
------------------------------------------------------------------------
Unless otherwise specified, the following is automatically waived when
printing or duplicating is to be accomplished on commercial contract
Sizing: Paper shall be surface- and internal-sized suitable for
satisfactory printing on both sides of the paper on high-speed offset
presses equipped with continuous flow or brush dampening systems.
Color: Shall match the Government's standard sample for color. A
deviation of DE(CIELAB)=3.0 from the color standard for white and 2.0
for colored stocks is allowed. A color difference 1.0 DE unit between
felt and wire is permitted.
Surface: Shall be free from lint, fuzz, or any particles which will
pick, lift, fluff, or pile on the blanket under normal press
conditions. Paper shall lie flat with either no tendency to curl or
with a curl which can be overcome under reasonable working conditions.
Size and trim: Sheets: Paper shall be furnished in the size(s) ordered
and shall be flat, trimmed square on four sides with clean smooth
edges, and evenly jogged. A tolerance of 2 mm (\1/16\
inch) shall be allowed except for sheets 216 by 356 mm (8\1/2\ by 14
inches) or less; then a tolerance of 1 mm (\1/32\ inch)
shall be allowed. Successive sheets within any package shall not
differ from each other by more than 0.5 mm (\1/64\ inch). Paper with
the long dimension 813 mm (32 inches) or less shall be considered
square if the variation does not exceed 1 mm (\1/32\ inch); over
813 mm (32 inches), 2 mm (\1/16\ inch).
Watermark: Shall be the seal of the United States, with the word
``recycled'', one star, and the year of manufacture, on a basis of
four times on a sheet 432 by 559 mm (17 by 22 inches), one in each
quarter. The watermark shall be clear and legible. When viewed from
the felt side of the sheet, the design shall appear as illustrated,
but in proper size. Full size copy will be supplied upon request.
[Year of manufacture]
Grain: Direction of the grain on flat paper shall be as ordered.
Pressroom conditions: The bulk of this paper will be used in air-
conditioned pressrooms maintained at 24 deg.C 2 deg.C
and 45 pct 8 pct relative humidity.
---------------------------------------------------------------------------
\1\ Note, recovered material (cotton/linen) is not a postconsumer
recovered fiber.