ASK OUR DIY EXPERTS!

The installation of wiring is one of the first concerns people have with structural insulated panels (SIPs), but the reality of the challenge isn’t a big problem. The best way to install wires is by stringing them through floor and ceiling frames, then running the cables down slots routed through the interior surface of the OSB. Cut a plywood template to guide the travel of the router, speeding the operation. Vertical cuts in the OSB are completely acceptable and don’t interfere with wall integrity. Just be sure to avoid horizontal cuts since they greatly reduce panel strength. Extend the slots to 2” deep using a hot knife to remove foam, then install wiring and electrical boxes. Apply foam to the wire slots after inspection, then install interior wall surfaces.

Possible? Absolutely. If you have enough trees of the right size, species and quality (they have to be tall and straight), they can be harvested, milled and used for your timber frame. This is a wonderful story that will be part of your home for all of its existence. We would be sure to carve the details (date harvested, and date raised) into the frame somewhere as a permanent record and point of interest.

Now, I answered your “possible” question, but here are other questions to be answered befor…

Steph,

Thermax brand insulation is made by Dow. To find a distributor in your area call Dow Customer Information Group at 866-583-2583.

I’m always surprised by how much stuff accumulates underneath wall-to-wall carpet. Over the years — even if you’re diligent about cleaning —a lot of dirt filters through the weave to the subfloor. 

If your situation is anything like I’ve seen, most of the green, dustlike material is a combination of sand and small particles of foam underlay. A simple vacuuming is the first place to start. Ideally you should use a vacuum with a HEPA-rated filter, to avoid broadcasting fine dust out of the exhaust …

I'd just use a wood chisel to get most of the foam insulation off. Then I'd use a paint scraper to finish the job.

They could. However, the usual practice is to wrap any structural member (wood, concrete block, steel) with felt or roofing paper to keep any moisture from condensation on steel — or moisture that might be drawn out of the plaster or stucco or concrete — away from the straw. A moisture barrier such as plastic probably isn't the best solution for wrapping the structural members because moisture also tends to condense and collect on it.

Straw bale construction is based on the age-old …

Cleaning your small engine’s carburetor isn’t terribly daunting, but I recommend that you have the correct service manual for your engine and a carburetor rebuild kit on hand before tackling it. It’s a good idea to start this project without significant pressure to get your machine running that same morning, as it may take a bit of time.

You will need plenty of clean, lint-free rags; some carburetor cleaner (visit your local auto parts store; I prefer aerosol carb cleaner); glass, glazed-ceramic,…

Laminate flooring came to North America nearly 20 years ago. Laminates please a lot of people, but they disappoint more than a few homeowners, too. The outcome depends on the flooring you choose, where you use it and your expectations. Are you thinking about a new hard-surface floor for your home?  Laminates have a lot to offer, but there are things you need to understand that you won't find in sales brochures.

Originally developed in Europe, laminates are made of a high-density fiberboard core c…

It’s a good thing you asked because there’s something a whole bunch of experienced deck owners want to warn you about: It’s not easy to create a long-lasting deck finish.

Many people tell me stories about peeling, fading, mildew and deterioration of their decks—all within a year or two of brushing on hundreds of dollars worth of finish. This is actually a common experience for deck owners across America, though it doesn’t have to be. Successful deck finishing depends on understanding crucial fact…

There are a couple of ways to go, including simply leaving the wood bare. I’ve worked in buildings with unfinished wooden floors, and they perform quite well. That said, there are two reasons a finish makes sense: It helps the wood resist staining, and it makes it easier to remove the inevitable hardened glue blobs that build up on the floor of any wood shop. Oil-based urethane works well as a basic sealer. Exterior grade latex paint lasts even longer under gritty foot traffic.

May I make a sugge…