Basic Electrical Safety PDF Version  PowerPoint Version

Basic Electrical Safety
  • Course not designed to teach you to work on electrical equipment.
  • You will not be qualified to work on electrical equipment.
  • If you spot problems with electrical equipment you should report it to your supervisor.


  • Be familiar with the fundamental concepts of electricity.
  • Be familiar with the effects of electricity on the human body.
  • Be able to recognize common electrical hazards.
  • Be familiar with electrical protective devices.

Fundamentals of Electrical Hazards

  • To flow electricity must have a complete path.
  • Electricity flows through conductors

    • water, metal, the human body

  • Insulators are non-conductors
  • The human body is a conductor

Have You Ever Been Shocked?


  • More than 3 ma

    • painful shock

  • More than 10 ma

    • muscle contraction "no-let-go" danger

  • More than 30 ma

    • lung paralysis- usually temporary

  • More than 50 ma

    • possible ventricular fob. (heart dysfunction, usually fatal)

  • 100 ma to 4 amps

    • certain ventricular fibrillation, fatal

  • Over 4 amps

    • heart paralysis; severe burns. Usually caused by >600 volts

  • Hazards of Electricity

    • Electrocution/Shock/Burns/Death

  • Minimum distance from overhead lines 10 ft.

  • Inspect all electrical tools and equipment

    Frayed, cut, broken wires
    grounding prong missing
    Improper use of cube taps
    improperly applied or missing strain relief

Electrical Protection
  • Circuit Breakers

    • Provided to protect EQUIPMENT not people
    • Do not reset breakers with a line voltage higher than 120V and only reset if you know why it tripped
  • GFCI's

    • Provided to protect people
    • Trip range 4-6ma
    • Monthly test
  • Distance

    • If you sense the presence of an electrical hazard or exposed conductors that may be energized, keep you distance and STAY AWAY


Electrical Grounding

Figure 12 : Current flow in a properly grounded circuit

Figure 12 Illustration

Figure 12 Illustraction Continued
Figure 14: Shock from improperly grounded tool

Figure 14 Illustration

Figure 15: Fault conditions sensed by a GFCI

Figure 15 Illustration

Figure 16: Correctly wired duplex receptacle

Figure 16 Illustration

Fundamentals of Electrical Hazards

  • Voltage

    • electrical pressure (water pressure)

  • Amperage

    • electrical flow rate (gallons/min)

  • Impedance

    • restriction to electrical flow (pipe friction)

  • Circuit

    • path of flow of electricity

  • Circuit Element

    • objects which are part of a circuit and though which current flows.

  • Fault

    • current flow through an unintended path.

  • What is Grounding?

    • Protection from electric shock

      • normally a secondary protection measure

  • A ground is a conductive connection

    • between electrical circuit or equipment and earth or ground plane

    • creates a low resistance to the earth.

Basic Rules of Electrical Action

  • Electricity isn’t live until current flows

  • Electrical current won’t flow until there is a complete loop, out from and back to the power source.

Preventing Accidental Electrical Contact

Do's and Don'ts

  • Do plug power equipment into wall receptacles with power switches in the Off position.
  • Do unplug electrical equipment by grasping the plug and pulling. Do not pull or jerk the cord to unplug the equipment.
  • Do not drape power cords over hot pipes, radiators or sharp objects.
  • Do check the receptacle for missing or damaged parts.
  • Do not plug equipment into defective receptacles.
  • Do check for frayed, cracked, or exposed wiring on equipment cords
  • Do check for defective cords clamps at locations where the power cord enters the equipment or the attachment plug.
  • Extension cords should not be used in office areas. Generally, extension cords should be limited to use by maintenance personnel
  • “Cheater plugs”, extension cords with junction box receptacle ends or other jury-rigged equipment should not be used.
  • Consumer electrical equipment or appliances should not be used if not properly grounded. (Look for the UL Label)
  • Employees should know the location of electrical circuit breaker panels that control equipment and lighting in their respective areas. Circuits and equipment disconnects must be identified
  • Temporary or permanent storage of any materials must not be allowed within 3 feet of any electrical panel or electrical equipment.
  • Any electrical equipment causing shocks or with high leakage potential must be tagged with a Danger tag or equivalent.

Myths and Misconceptions

  • Electricity takes the path of least resistance.
  • Electricity wants to go to ground.
  • If an electric tools falls into a sink or tub of water, the item will short out.
  • AC reverse polarity is not hazardous.
  • It takes high voltage to kill; 120 volts is not dangerous.
  • Double insulated power tools are doubly safe and can be used in wet and damp locations.

Safety First: The Safe Way is the Best Way

This paper appears in the eLCOSH website with the permission of the author and/or copyright holder and may not be reproduced without their consent. eLCOSH is an information clearinghouse. eLCOSH and its sponsors are not responsible for the accuracy of information provided on this web site, nor for its use or misuse.

 eLCOSH | CDC | NIOSH | Site Map | Search | Links | Help | Contact Us | Privacy Policy

Other Job Site Trade Hazard Site Map Search Spanish Items Help Links Contact eLCOSH Non-English Materials Training Materials NIOSH Home CDC Home eLCOSH Home