Marine
Accident Brief
Engineroom Fire on the U.S. Passenger
Vessel Columbia
in Wrangell Narrows, near Wrangell, Alaska, on May 28, 2003
NTSB/MAB-04/02 [PDF version]
Accident Number: | DCA03MM033 |
Vessel: | U.S. Passenger Vessel Columbia O.N. 557340, 418 feet long (LOA), 3,946 gross tons, inspected, built in 1974 |
Accident Type: | Fire |
Location: |
Wrangell Narrows near Wrangell, Alaska |
Date: |
May 28, 2003 |
Time: |
0144 local |
Owner: |
State of Alaska |
Property Damage: |
$125,000 |
Injuries: |
None |
Complement: |
Crew 43 Passengers 170 |
About 0121 on May 28, 2003, the Alaska Marine Highway System
ferry Columbia, with 170 passengers on board,
departed Petersburg, Alaska, en route to Wrangell, Alaska. The ferry was equipped with three
ship-service diesel generators, located in the auxiliary engine room, and the
vessel’s electrical load required that two of the generators be online during
normal underway operations. On this morning, the ship-service generators in use
were Nos. 1 and 2.
Shortly after the Columbia left port, an oiler on watch made his normal inspection rounds of the engineering spaces. While the oiler was in the auxiliary engine room, he noticed an odor suggesting that an equipment item was overheating. He said that he was unable to locate the source of the odor and, about 0135, went to the control room and informed the watch engineer and the chief engineer of his observations.
The chief engineer said that he immediately went into the auxiliary engine room. He was searching for the source of the smell and standing between the diesel engines for the Nos. 1 and 2 generators when, about 0144, he heard an unusual noise and saw a burst of flames in the area of the No. 2 generator’s cooling fan ports. The vessel then lost electrical power, which shut down the electrically driven main engine fuel pumps. The main engines then shut down, leaving the ship without propulsion power and the ability to steer while it was in Wrangell Narrows (figure 1).
Figure
1. Wrangell Narrows, where the Columbia
lost electrical power.
|
The chief engineer
noticed that the circuit breaker for the No. 2 generator had tripped on the
main switchboard. He then ordered the shutdown of the No. 2 generator’s diesel
engine remotely from the control room and returned to the auxiliary engine
room, accompanied by the junior engineer. The chief engineer and the junior
engineer observed a fire beneath the turbocharger of the No. 2 generator’s
diesel engine. The junior engineer put out the fire using a portable CO2
extinguisher; however, the smoke continued to increase and became so thick that
the two men had to leave the auxiliary engine room.
Upon returning to
the control room, the chief engineer telephoned the bridge to report the
generator fire and to request that the firefighting team be called out. The
chief engineer then ordered all off-watch engineering personnel to report to
assist with the emergency.
The firefighting team reported to the engine control room. After being briefed about the fire by the chief engineer and the junior engineer, two men from the team (the chief mate and the third engineer), wearing fire-protective clothing and self-contained breathing apparatus, entered the auxiliary engine room about 0153. Once in the auxiliary engine room, the third engineer discovered that the air filter on the turbocharger of the No. 2 generator was on fire, producing billowing smoke that filled the space. The third engineer lifted the burning air filter out of the air intake, and the chief mate put out the fire using a portable CO2 fire extinguisher. The team then began inspecting the auxiliary engine room for other fires and damage. A short time later, the chief mate noticed that the air filter had reignited, and the team doused the filter with water to extinguish the fire. By 0207, the Columbia crew established that the No. 2 generator fire was extinguished and, in accordance with the company’s operating procedures, posted a reflash watch as a precaution.
The Columbia’s
engineers ventilated the engineering spaces and then started the Nos. 1 and 3
ship-service diesel generators. After electrical power was fully restored, the
crew restarted the two main engines at 0230, and engine control was shifted to
the bridge so that the navigation watch could resume the voyage to Wrangell.
On May 28, 2003, the
Columbia arrived in Ketchikan, Alaska, where Alaska Marine Highway System
officials had the No. 2 generator
removed so that it could be sent to an electrical repair facility. Consulting
engineers also checked the other ship-service generators. The Columbia’s
engineers told the consulting engineers that generators Nos. 1 and 3 had
operated satisfactorily while en route to Ketchikan; however, megger[1] tests revealed that the No. 3 generator had
a short (low resistance to ground) on one phase and was not suitable to
operate. Agency officials, therefore, also had the No. 3 generator removed from
the engineroom so that it could be sent to the electrical repair facility to be
examined further and repaired. Because the Columbia now lacked two operable ship-service
generators, the ferry had to be taken out of service. On June 4, 2003, the Alaska Marine Highway System had a new generator installed so that
the ferry could operate, and the Columbia was returned to service.
According to agency officials, the Nos. 2 and 3
ship-service generators on the accident ferry had last been overhauled in 1999.
The examination of generator No. 3 at
the repair facility in early June 2003 revealed that the insulating varnish
appeared to be in “excellent condition.” Examiners found no evidence of an
insulation breakdown that could account for the low megger reading. The
contract repair technicians then rewound the generator, and, on June 12, 2003,
megger tests were conducted indicating that the generator was in proper
operating condition. The tests on June 12 were witnessed by the port engineer
for the Alaska Marine Highway System and a representative of the American
Bureau of Shipping (ABS), the ferry’s classification
society. On June 13, 2003, while the Columbia was in Bellingham, Washington, the repaired
generator was loaded onto the ferry. Installation of the generator was
completed while the ferry was underway. On June 20, 2003, the Columbia returned
to Bellingham, where the repaired generator underwent a day of testing under
the supervision of an ABS representative, who determined that the generator
operated satisfactorily.
The initial examination of ship-service generator No. 2 showed that the equipment unit had sustained heavy damage from the fire. Much of the copper wiring in the lower part of the generator had melted and vaporized. The Alaska Marine Highway System contracted for an in-depth failure analysis, which was conducted in July 2003. Consultant engineers removed the remaining windings and inspected them for evidence of improper assembly or insulation failures, but could find no failure condition. The examining contractor concluded that the insulation breakdown had occurred in the lower part of the generator, which had been mostly destroyed. He further concluded that
an electrical event or events, possibly the switchboard fire of a few years ago or the indiscriminate application of Hi-Pot testing during the dip and bake process, caused aging or hard spots in at least one of the windings near the bottom of the generator. This caused a short between turns which increased the current in that coil. The heat was eventually enough to cause additional turns to become shorted and then to start the melting process in the winding. As the molten copper started to flow, it shorted windings phase to phase, and the event quickly became a catastrophic failure.
The switchboard fire referred to by the contractor occurred on June 6, 2000.[2] At the time, the Nos. 1 and No. 2 generators were in operation. The engineer on watch was making an inspection round of the engineering spaces when he observed that the No. 2 generator was surging “from a slower speed to a higher speed” and was moving erratically on its foundation. The engineer proceeded to the control room, where he observed fire coming out of the switchboard. The fire was subsequently extinguished by the crew. An investigation into the fire determined that it had been caused by a short circuit in the switchboard, and that the short circuit had caused “substantial damage” to the switchboard. The No. 2 generator was examined following the accident and found to be undamaged.
The National Transportation Safety Board determines that the probable cause of the fire and the destruction of the wiring in the No. 2 ship-service generator on the Columbia was a breakdown in the generator’s wiring insulation.
Adopted: April 19, 2004
[1] A test instrument used to measure insulation resistance and other high resistances.
[2] For more information, see National Transportation Safety Board, Fire On Board the U.S. Passenger Ferry Columbia, Chatham Strait, Near Juneau, Alaska, June 6, 2000, Marine Accident Report NTSB/MAR–01/02 (Washington, DC: NTSB, 2001).