U.S.-Chile Free Trade Agreement
Using the Rules of Origin to Qualify your Product
Those familiar with the North American Free Trade Agreement (NAFTA) between the United States, Canada, and Mexico, will recognize some aspects of this agreement’s Rules of Origin as the U.S. Chile FTA was largely modeled upon the NAFTA. There are however some important differences, which require the close attention of the US exporter. If you are new to this process, you may wish to read or print out for later reading, the section below on How to Read the Rules of Origin, prior to reviewing the U.S.-Chile FTA Rules of Origin.
The rules of origin are available at the U.S. International Trade Commission's website. On the International Trade Commission's website, click on "Current HTSA Edition by Chapter," which is located on the right side in the "HTS Tools" box. Then, in the body of the text, click on "General Notes; General Rules of Interpretation; General Statistical Notes." Within the "General Notes" you will find the U.S.-Chile FTA Rules of Origin in General Note 26. (The General Notes section is a large document and may take some time to open on your computer.)
How To Read the Rules of Origin
Rules of origin are written in terms of the Harmonized System of Tariff Classification, otherwise known as Schedule B codes. Therefore, the first step to using the “rules” is to obtain the appropriate code for the product in question.
A rule of origin may consist of:
1) A change in tariff classification;
2) A regional value-content requirement;
3) Both a change in tariff classification and a regional value content requirement.
Note: It is necessary to refer to the rule associated with the product being exported. Regional value content can only be applied when it is allowed under a product-specific rule.
Some Examples
1) An example of a rule that employs a simple tariff shift is:
Rule of Origin: "A change to heading 1902 through 1905 from any other chapter."
Products: Breads, pastries, cakes, biscuits (HS 1905.90)
Non-U.S. or Chilean input: Flour (classified in HS chapter 11), imported from Europe.
Explanation: For all products classified in HS headings 1902 through 1905, all non-U.S. or Chilean inputs, must be classified in an HS chapter other than HS chapter 19 in order for the product to obtain preferential duty treatment. These baked goods would qualify for tariff preference because the non-originating goods are classified outside of HS chapter 19. (The flour is in chapter 11). However, if these products were produced with non-originating mixes, then these products would not qualify because mixes are classified in HS chapter 19, the same chapter as baked goods.
2) An example of a rule that employs both the “tariff shift” and “regional value content” is:
Rule of Origin: “A change to subheading 9403.10 through 9403.80 from any other heading; or
A change to subheading 9403.10 through 9403.80 from any other subheading, including another subheading within that group, provided there is a regional value content of not less than:
(a) 35 percent when the build-up method is used, or
(b) 45 percent when the build-down method is used.”
Product: Wooden Furniture (HS # 9403.50)
Non US or Chilean input: Parts of furniture (classified in 9403.90), imported from Asia.
Explanation: Wooden furniture can qualify for preferential tariff treatment in two different ways – through a tariff shift, or a combination of a tariff shift and regional value content requirement.
Because the non-U.S. Or Chilean input is classified in the same heading (9403) as the final product in this case, the good does not make the simple “tariff shift” in the first rule. Moving down to the second rule though, the good can meet the tariff shift because the non-originating component is from a different subheading than the final product. For the good to qualify as originating, however, it must also pass the regional value content test.
Regional Value Content
The Regional Value Content test allows the good to qualify using either one of two methods. These are the builddown and build up methods.
Builddown method:
Regional Value Content (RVC) =(( Adjusted Value - Value of Non-Originating Materials)/ Adjusted Value)X 100
Buildup method:
Regional Value Content (RVC) = (Value of Originating Materials/Adjusted Value) X 100
Using the example above then:
We will assume that the adjusted value for the piece of furniture in question is $1000.00.
The value of non-originating materials used in the production of the good excludes, according to Article 4.3:
1) the costs of freight, insurance, packing, and all other costs incurred in transporting the material to the location of the producer;
2) duties, taxes, and customs brokerage fees on the material paid in the territory of one or both of the Parties, other than duties and taxes that are waived, refunded, refundable, or otherwise recoverable, including credit against duty or tax paid or payable;
3) the cost of waste and spoilage resulting from the use of the material in the production of the good, less the value of renewable scrap or byproducts; and
4) the cost of originating materials used in the production of the non-originating material in the territory of a Party
Our assumed Value of Non-originating Materials in this case is $500.00.
Plugging this into the builddown formula:
Regional Value Content (RVC) = ($1000 – $500)/$1000 X 100 = 50%
We can see that the percentage is greater than the 45% required by the rule. Therefore, the good qualifies as originating.
If instead, we use the buildup formula:
Regional Value Content (RVC) = $500/$1000 X 100 = 50%
The Regional Value Content is again 50% and is greater than the 35% required by the rule. With either method, the good specified in this example qualifies as originating under the U.S.-Chile FTA.
In addition to the rules of origin, it is sometimes appropriate to consider other factors found in Chapter Four of the US Chile-FTA when determining the origin of a product.
Prepared by the International Trade Administration
Trade Information Center