After dislocation or stunning, the rabbit is hung by one of the hind legs above the hock joint. The head is immediately removed to allow complete bleeding. The forefeet are then removed. The next step is to cut the skin around the hock joints of the legs and then to cut between these points across the lower part of the body. Remove the tail and pull the skin down and forward over the body. The skins of young or fryer age rabbits are easily removed in this way; it is more difficult to remove the skins of older rabbits. If skins are saved for marketing, they should be handled as indicated in the Rabbit Skins and Pelts section.
After the head, forefeet and skin are removed, the carcass, while still hanging, is opened to remove the viscera. Make a cut from the lower part of the abdomen near the anus to the mid-point of the lowest rib. The intestinal tract and lungs are normally removed. Liver, kidneys, and heart remain with the carcass. Remove the carcass from the hanger and cut off the rear feet at the hock joint.
Wash the carcass with clean, cold water to remove hair and any other soil or debris, and store it at a cold temperature, preferably at 35oF. and not over 40oF. Do not hold dressed carcasses for any length of time in water as they absorb excess moisture which becomes considered as a contaminant. When large numbers of rabbits are to be slaughtered, the operation on an assembly line basis is much more rapid and efficient.
Dressed rabbits may be sold whole or can be cut into parts. Various types of marketing devices (plastic cartons and trays) are available for packaging one or more carcasses.
Age |
New |
Dutch |
8 weeks | 55.9% | 60.3% |
13 weeks | 59.2% | 63.3% |
Mature | 58.2% | 62.8% |
Animals that are in average condition or slightly better than average have dressing percentages of about 55 percent while good quality animals reach a dressing percentage of 60 percent or higher. The data shown above were obtained with New Zealand and Dutch rabbits of different ages that were fed a commercial rabbit feed.
The dressing percentages of the Dutch were greater than those of the New Zealand, indicating breed variations. The percentage also increased between 8 and 13 weeks of age, but declined slightly in the mature rabbits. Mature rabbits in this study were limit-fed which may account in part for the lower dressing percentages. Normally, dressing percentage increases with age until rabbits approach maturity.
Whether the pelts from meat slaughtering should be saved and prepared for marketing will depend upon the market demand and value, the type and number of rabbits being slaughtered and the time and facilities available for preparing the skins. It is unlikely that the small producer slaughtering his own animals will find it economically worthwhile to process the skins.
Rabbit skins and pelts vary widely in quality and value. The different types of fur characteristics vary depending on the breed type. Skins from young of any breed are normally of poor quality and of less value than those from adult animals. Those with dense fur, that is not easily removed from the skin, are most desirable.
Preparation of skins or pelts for market begins with the removal at slaughter. Exercised care to avoid cuts or tears, and remove body fat that often remains attached to the skin. As the pelts are removed, turn them inside out while still warm and moist. Place them on wire stretchers or shapers with the front leg casings on one side. Shapers can be made from No. 9 gauge galvanized wire. The shapers extend or expand the pelts to their full length, but do not stretch them out of shape. Fasten the rear legs to the ends of the wire shapers with a clothes pins or some other fastener.
Hang the pelts in a well-ventilated drying area, but not in direct sunlight. After the skins are dry the wire shaper is removed. Do not use salt or other chemicals on skins, but as they are being packed for storage or shipment, naphthalene (moth crystals) or paradichloro-benzene may be placed in the packaging container as an insect repellent.
Dried skins are softened by soaking in several changes of water for about 1-3 hours. Time required for softening will vary; soaking time is kept to a minimum since excessive soaking tends to loosen the hair. Addition of borax or bicarbonate of soda (about 1 ounce per gallon) aids in softening, and a little soap or detergent aids in removal of the fat.
Remove the paste and wash skins in a solution of borax or soda (1 ounce per gallon of water). Squeeze out (do not wring) excess solution; rinse in plain water and squeeze out excess. Stretch, and when nearly dry, work the skin by rubbing and pulling over the edge of a table, as in polishing shoes with a cloth. Stretching and working the skin is necessary for softening the finished skin. If the skin is rough, it can be sanded with a coarse sandpaper block. A thin coating of neat's foot oil, glycerin, or other leather conditioner improves pliability.
This process is considered slightly better than the salt-acid method that follows, but the finished product is usually harder and more working may be required to make it pliable. It may be necessary to resoak the skin, partially dry it, and repeat the rubbing in order to make it more pliable.
Tanning is also accomplished by soaking skins for 2-4 days in the solution before addition of flour. This amount of solution is adequate for 3 or 4 rabbit skins.
Materials for tanning may be obtained from certain biological supply companies or handcraft shops. Procedures for different tanning methods will vary and instructions should accompany materials marketed for tanning.
Last modified: Thursday, 14-August-97.
URL: http://www.msstate.edu/dept/poultry/rabslau.htm
Mississippi State University is an equal opportunity institution.