![]() |
ENVIRONMENTAL
EDUCATION SERIES
ENVIRONMENTAL QUALITY Agriculture & Natural Resources |
|
Proper selection of application equipment and the calibration and evaluation of its performance are essential for satisfactory results. Even the best equipment needs calibration checks, especially when changing from one type of material to another, when changing rates of application, and when altering speeds or other operating conditions.
Calibration
Calibration checks of bulk fertilizer equipment should show the type of spread pattern, including the degree of uniformity obtained across the swath, the effective swath width, and the rate of application. To be effective, the system used to check calibration should be accurate, easily understood by the operator, and simple to perform.
One practical method of calibrating fertilizer and lime spreaders requires the following items:
Materials collected
grams per sq. ft. |
Rate of application
lbs. per acre |
|
|
||
1
5 10 15 20 25 |
96
480.2 960.3 1440.5 1920.7 2400.8 |
|
|
For applications up to approximately 1,100 lbs per acre, 15 test tubes that are ½” inside diameter and 4½” are used. The 15 trays are usually placed as shown in Figure 1. All trays are placed at five foot intervals except for trays 7 and 9 which are placed six feet from tray 8, the center (Figure 1). The trays must have grid baffles to prevent fertilizer from bouncing out. Trays must be as level as possible when collecting material.
Figure 1. Field layout of collecting trays showing extra clearance on each side of the center tray for spreader wheels. All trays are placed at 5' intervals except for trays 7 and 9 which are placed 6 feet from the center tray, 8.
The spacing interval between trays can be changed, depending on swath width. The spreader is adjusted for a given rate of application and operated at normal field speed in a direction perpendicular to the line of trays while straddling the middle tray. Material collected in each tray is then poured into the corresponding test tube in the rack.
The amount of material in the test tubes provides a quick, visible evaluation of the spread pattern (Figures 2 and 3). If the spread pattern is uniform across the swath, as on the left side of Figure 3, and the proper swath width is used, the material will be deposited uniformly on the land.
The effective swath width can be found by locating the point on the right and left side of the swath where the tubes are filled to about one-half the height found in the center tubes. The distance between these points is the effective swath width and should be used as the swath spacing (Figure 2).
If the material weight is 65 lbs./ft3 and you have any of the acceptable patterns on the left side of Figure 3, the first 1/2" material in the center tube represents a rate of approximately 100 lbs./acre. Each additional 3/8" of material after the first 1/2" represents an additional 100 lbs per acre. This is assuming the material in each tube is collected from an area of 1.37 square feet (collection pans 11.75" x 16.75") and test tubes of inside diameter of 1/2" are used. Fertilizers vary in moisture content and in size and particle density. These variations will cause slight errors in the indicated rates of application, but this method provides a close approximation.
Where application rates are more than 1,100 lbs per acre, larger test tubes are used with the same collecting trays. These test tubes have an inside diameter of 7/8" and are 8" to 10" tall. The first l/l6" of material in these tubes represent approximately 500 lbs per acre, and each additional 1/2" depth indicates about 500 lbs per acre. The larger test tubes are suggested for evaluating spread patterns for rates of application between 1,000 and 6,000 lbs per acre, such as in the application of lime.
CENTER COLLECTING TRAY SPACING (FEET)
Figure 2. The spread pattern is determined by collecting the material in trays and pouring it into test tubes. Material overlap, as shown, results when swath spacing equals the effective swath width. This is a typical pattern one might expect from a doublespinner fertilizer truck. This does not depict an ideal pattern.
Figure 3. Typical double-spinner spreder distribution pattern. Any of the first three are acceptable.
Adjustment In Spread Pattern
Once a spread pattern is evaluated, determine what, if any, adjustments can be made to improve the pattern. If the pattern is unacceptable, determine the problem.
Spread patterns for a double-spinner, dry fertilizer applicator can be classified into six different types (Figure 3). The flat top, oval, and pyramid patterns are the most desirable because they lend themselves to uniform overlapping of the swaths. The most common undesirable patterns are the M, W, and offside (skewed or lopsided) patterns. You can improve the M pattern by making one or more of the following adjustments (Figure 4).
Lopsided pattern, either right or left, may result from twin spinner applicators because of uneven delivery of fertilizer material to the spinners. An improperly adjusted flow divide is usually the cause. Operations on steep slopes can also produce heavier flow to the downhill side if an effective flow divider is not included in the system. This problem can be overcome, to some extent, by proper overlap between swaths and a circular pattern application.
Single spinner solid applicators can also produce a lopsided pattern when the delivery of the material to the spinner is not positioned properly. If the right half of the pattern from a clockwise rotating spinner is heavier than the left half, any of the following adjustments will improve the pattern by delaying the release of fertilizer from the spinner (Figure 5).
Figure 4. Dual spinner solid fertilizer applicator showing adjustments for corrections of an M distribution pattern, characterized by low delivery in the center and high delivery on the edge of the swath.
Figure 5. Four adjustments to correct "heavy right" distribution patterns from a single spinner (fan) solid fertilizer applicator. These four corrections allow material to ride the spinner further and deposit toward the left side. Corrections for "heavy left" patterns are opposite.
Accurate Spreading Requirements
When practical, drive spreaders around fields in a perimeter or circular pattern to minimize the effect of variations in spread patterns.
Granular or prilled material of uniform particle size will give the
most even application. It is best to select materials for blends that are
approximately the same particle size and shape and have approximately the
same density and moisture content (this prevents segregation of materials
in the spreading operation). Vertical baffles in gravity bins are effective
in preventing segregation.