|
|
|
Decide
on the procedures needed based on how respirators are being used |
Option 1: Cleaning
for Single users: the same person uses the same respirator all the time.
NOTE:
this option should not be used if respirators
are not marked with user names.
|
- Use
Procedure 1 for basic cleaning of single user respirators.
- If
desired or required, add Procedure 2 to sanitize single user respirators
after cleaning.
|
Option
2: Cleaning
for Multiple users: different persons will be sharing respirators. |
- Use
Procedure 3 to clean and sanitize respirators.
Note
that Procedure 3 is equal to combining
procedures 1 and 2. |
|
Gather
equipment and supplies |
Procedure
1
|
- 2
buckets
- Warm
water
- Thermometer
- Alcohol
free wipes and or soft brush and sponge
- Neutral
detergent - no lanolins or oils - (most dish detergents will work)
- Table
or work surface
|
Procedure
2 |
- 2
buckets
- Warm
water
- Thermometer
- Metric
graduated cylinder for measuring small quantities
- Quaternary
ammonia disinfectant OR hypochlorite (household bleach) OR iodine solution
OR other commercially available cleansers of disinfectant quality that
are recommended by the respirator manufacturer
- Table
or work surface
|
Procedure
3 |
- 4
buckets and the materials listed above for procedure 1 and 2.
|
|
Description
of Procedures |
Procedure
1
Generic Single User Cleaning Procedure (the same person uses the same respirator
all the time). Cleaning can be done as often as required. Atmosphere supplying
and emergency use respirators should be cleaned and sanitized after each
use. THE RESPIRATOR MUST BE CLEANED AND SANITIZED BEFORE IT CAN BE TRANSFERRED
TO ANOTHER INDIVIDUAL. |
- Prepare
2 buckets (2 gal/7.5 L) of fresh warm water; follow sequence of use
as described below.
- Do
not use boiling or hot water. Water Temperature should be less than
110 F.
- Disassemble
respirator, removing cartridges and/or filters and any external accessories
such as communications, hoods, head harness (if possible) and eye lens
outserts. Do not remove the valves because they are easy to lose.
- Bucket
1. Clean respirator and associated parts (excluding cartridges and/or
filters) with alcohol free wipes, or by immersing in a warm water cleaning
solution, scrubbing with a soft brush or sponge. Do not brush eye lenses.
Use a neutral detergent cleaning solution that does not contain lanolin
or oils.
- Bucket
2. Rinse in fresh, warm water. Running water is better than immersion
if available. Thorough rinsing is important to keep detergents or disinfectants
from drying on the respirator. [See OSHA 29CFR1910.134, Appendix B-2,
running water for rinsing (if available) is preferred over immersion.]
- Replace
cleaning solution and rinse water after approximately 20 respirators
have been cleaned, or as needed.
- Allow
the respirator to air dry in a non-contaminated environment. Do not
dry with heaters or in sunlight. Respirators can be reassembled before
or after drying.
- Prior
to re-use, conduct checks as recommended by the manufacturer's manual
to assure that the system is ready to be placed in operation. It is
very important to check that the inhalation and exhalation valves are
in place prior to use.
|
|
Procedure
2
IF
Sanitization is desired or required: |
- Clean
respirator as described above. The final air drying step is not necessary.
- Prepare
2 buckets (2 gal/7.5L) of fresh warm water; follow sequence of use as
described below.
- Do
not use boiling or hot water. Water Temperature should be less than
110 F.
- Bucket
1. Disinfect respirator by immersing in a disinfectant water solution.
A quaternary ammonia disinfectant (one packet per 2 gallons or per manufacturer's
recommendation), or a hypochlorite (1 oz [30milliliters] household bleach
in 2 gal [7.5 L] water) solution, or an aqueous solution of iodine (50ppm
of iodine, made by adding 0.8 milliliters of tincture of iodine to one
liter of water at 110 F) can be used.
- Bucket
2. Rinse in fresh, warm water. Thorough rinsing is important to keep
detergents or disinfectants from drying on the respirator.
- Replace
sanitizing solution and rinse water after approximately 20 respirators
have been sanitized, or as needed.
- Allow
the respirator to air dry in a non-contaminated environment. Do not
dry with heaters or in sunlight
- Prior
to re-use, conduct checks as recommended by the manufacturer's manual
to assure that the system is ready to be placed in operation It is very
important to check that the inhalation and exhalation valves are in
place prior to use.
|
|
Procedure
3
Respirator Cleaning and Sanitization Procedures
Generic Multiple User Cleaning and Sanitizing Procedure (different people
use the same respirator). Atmosphere supplying and emergency use respirators
should be cleaned and sanitized after each use. THE RESPIRATOR MUST BE
CLEANED AND SANITIZED BEFORE IT CAN BE TRANSFERRED TO ANOTHER INDIVIDUAL.
|
- Prepare
4 buckets (2 gal/7.5 L) of fresh warm water; follow sequence of use
as described below.
- Do
not use boiling or hot water. Water Temperature should be less than
110 F.
-
Disassemble respirator, removing cartridges and/or filters and any external
accessories such as communications, hoods, head harness (if possible)
and eye lens outserts Do not remove the valves because they are easy
to lose.
- Bucket
1. Clean respirator (excluding cartridges and/or filters) with alcohol
free wipes, or by immersing in a warm water cleaning solution, scrubbing
with a soft brush or sponge. Do not brush eye lenses. Use a neutral
detergent cleaning solution that does not contain lanolin or oils.
- Bucket
2. Rinse in fresh, warm water. Running water is better than immersion
if available. Thorough rinsing is important to keep detergents or disinfectants
from drying on the respirator. [See OSHA 29CFR1910.134, Appendix B-2,
running water for rinsing (if available) is preferred over immersion.]
- Bucket
3. Disinfect respirator by immersing in a disinfectant water solution.
A quaternary ammonia disinfectant (one packet per 2 gallons or per manufacturer's
recommendation), a hypochlorite (1 oz [30ml] household bleach in 2 gal
[7.5 L] water) solution, or an aqueous solution of iodine (50ppm of
iodine, made by adding 0.8 ml of tincture of iodine to one liter of
water at 110 F) can be used.
- Other
commercially available cleansers of equivalent disinfectant quality
when used as directed can be used, if their use is recommended or approved
by the respirator manufacturer [See 29 CFR910.134, Appendix B-2, Para
I, D.3.]
- Bucket
4. Rinse in fresh, warm water. Running water is better than immersion
if available. Thorough rinsing is important to keep detergents or disinfectants
from drying on the respirator. [See OSHA 29CFR1910.134, Appendix B-2,
running water for rinsing (if available) is preferred over immersion.]
- Replace
cleaning solution, sanitizing solution, and rinse water after approximately
20 respirators have been sanitized, or as needed.
- Allow
the respirator to air dry in a non-contaminated environment. Do not
dry with heaters or in sunlight Respirators can be reassembled before
or after drying.
- Prior
to re-use, conduct checks as recommended by the manufacturer's manual
to assure that the system is ready to be placed in operation It is very
important to check that the inhalation and exhalation valves are in
place prior to use.
|
General
notes |
- The
process should always include these steps:
Cleaning Sanitizing
Rinsing
Drying
Reassembly
Inspection Prior to Use
- Respirators
can be divided up into batches of 20, as water and cleaning fluids will
be changed after 20 respirators are cleaned.
- It
is better to disassemble and clean one respirator at a time. Group respirators
together by manufacturer if more than one will be disassembled at a
time to avoid getting parts confused.
- Different
respirator manufacturers market different cleaning and sanitizing solutions.
Contact them for details regarding these products.
- Quaternary
ammonia is a disinfectant that contains ammonia (NH4) with additional
surfactant (detergent) action. It is used as a disinfectant with cattle
producers and animal health workers. It has a wide germicidal range,
is non-corrosive, and is considered very effective for sanitizing cleaned
surfaces.
- Other
non-alkaline biodegradable disinfectants have been tested and are recommended
by leading respirator manufacturers that are effective against HIV-1
(AIDS virus).
September
2001
|