Fatality Assessment and Control Evaluation (FACE) Program |
|
Construction Laborer Dies After Being Run Over and Crushed by a Grader at a Road Construction Site - North Carolina |
| |||||||||||
SummaryOn December 4, 2001, a 54-year-old male construction laborer (the victim) was fatally injured when he was run over and crushed by a motor grader (hereafter termed grader). At the time of the incident, the grader operator was driving the grader in reverse on a road under construction in a housing development. The victim and a coworker were standing in the road at the rear of their parked pickup truck discussing the next stage of their work when the grader operator began backing in their direction. The coworker saw the grader backing toward them and yelled to the operator to stop. The operator did not hear the warning. The back tire of the grader struck the victim, knocking him down. The operator stopped the grader when it struck the rear of the parked pickup truck. The victim was under the rear tire of the grader. The coworker told the operator to pull forward and then called 911 on his cell phone. Emergency medical services (EMS) and police personnel responded within minutes. Emergency care was initiated by EMS personnel and the victim was transported to an area hospital where he died approximately 90 minutes after the incident. NIOSH investigators concluded that, to help prevent similar occurrences, employers should
Additionally,
IntroductionOn December 4, 2001, a 54-year-old male construction laborer (the victim) was fatally injured when he was run over and crushed by a grader that was being operated in reverse. On January 8, 2002, officials of the North Carolina Occupational Safety and Health Administration (NCOSHA) notified the National Institute for Occupational Safety and Health (NIOSH), Division of Safety Research (DSR), of the incident. On March 5, 2002, a DSR occupational safety and health specialist met with both the NCOSHA compliance officer assigned to the case and his supervisor to discuss the case and to review information collected in the course of their investigation. On March 6, 2002, the employer and his newly appointed safety manager were interviewed. The grader operator and coworker were no longer working for the company and were not available for interview. Official reports from the police department and the coroner's office and photographs taken at the scene by NCOSHA and the City County Bureau of Investigation were reviewed. The employer was a road construction contractor that had been in business for 7 years. The company employed 60 to 70 workers on various sites during the peak road-building season. The incident occurred on a road under construction in a housing development. The road was not yet open to public travel and had been under construction for 3 weeks. Nine workers were on site the day the incident occurred; four laborers (including the victim) performed general duties which included shoveling spilled gravel back onto the roadway and filling in low spots, two grader operators, two roller operators, and one excavator operator. The employer had a general written safety program. Although the company had a safety policy requiring workers on foot to wear high-visibility vests while working on site, none were being used at the time of the incident. The victim had worked for the company for 6 months. New employees, including the victim, were provided basic 1- to 2-hour orientation to the job which primarily covered benefits, the type of clothing and shoes required, and the tasks workers were to perform. The company held two to three safety talks per year, but attendance was not mandatory. The victim had not attended any safety talks. According to the employer, the grader operator involved in the incident had worked for the company as a grader operator for 5 years and had learned to operate the grader through on-the-job training. This was the company's first workplace fatality. Following this fatality, the company hired a full-time safety manager and developed a more comprehensive employee policies and safety handbook that included operating procedures to follow while operating or working around mobile equipment. Back to TopInvestigationRoad work, which included cutting the road, installing curbs and gutters, graveling, and grading had been in progress for 3 weeks. The road was not open to public travel. On the day of the incident, the employer assigned two three-man crews to the site plus two additional laborers and one excavator operator. Each three-man crew was comprised of one grader operator, one roller operator, and one laborer. Workers arrived at the site at 7 a.m. During the morning, the grader operators spread gravel, the roller operators compacted the gravel, the excavator operator made back cuts where compaction was poor due to soil conditions, and the laborers hand shoveled gravel into low spots. The workers planned to stop for a lunch break at 2:30 p.m. Shortly before 1:45 p.m. Grader Operator #1 asked the victim and his coworker to use the pickup truck to haul a tamper and drop it off along the roadway. At approximately 1:45 p.m., after picking up the tamper, the victim and a coworker drove a pickup truck around the work site to ask coworkers for food and drink requests. At approximately the same time, Grader Operator #1 was at the entrance to the development and was informed by the company owner that the company's water truck was on its way. He then drove his grader down to the location of grader #2 to inform Grader Operator #2 that the water truck was on its way (Figure 1 illustrates work-site layout). While Grader Operator #1 was talking with Grader Operator #2, the victim and coworker stopped their truck and asked Grader Operator #2 for his food order. Grader Operator #1 told NCOSHA investigators he saw the victim and his coworker leave in their work truck. After Grader Operator #1 finished his conversation with Grader Operator #2, Grader Operator #2 drove his grader down a slope and around a curve to the east where he resumed his work. Grader Operator #1 began to back his grader uphill and northwest toward the entrance to the development. No information was available regarding the grader's speed at the time of the incident. Based on the grader manufacturer's brochure for the make and model used on the day of the incident, the grader had six reverse gears that ranged in speed from 1.8 miles per hour to 20.9 miles per hour. In the meantime, the victim and his coworker parked the pickup truck alongside the curb on the right side of the roadway to drop off the tamper. They were approximately 400 feet from the location where Grader Operators #1 and #2 had been talking. The pickup truck was parked facing west toward the entrance to the development. The victim and his coworker left the truck running and unloaded the tamper and placed it along the curb on the passenger side of the truck. The coworker was facing toward the entrance and was checking the oil and gas levels in the tamper and was starting to tell the victim to go to the entrance to help other crew members when the incident occurred. Photo 1 illustrates the approximate location of the victim and coworker. The victim was standing at the rear of the truck on the driver's side facing the back of the truck, and the coworker was standing approximately 2 feet from the victim nearer the curb. Neither worker was wearing a high-visibility safety vest. The coworker looked up and saw the grader coming toward them. He yelled for the grader operator to stop. Grader Operator #1 did not hear the warning, and the back tire of the grader struck the victim in the upper back and knocked him to the ground. Grader #1 continued moving in reverse, striking the bumper and tailgate of the pickup truck (Photo 1). The operator stopped after the impact. The left rear tire of the grader had rolled on the victim's upper back and head. The coworker ran to the operator and told him to pull forward to free the victim. The coworker then used his cell phone to call 911. Emergency medical services (EMS) and police personnel received the call at 2:07 p.m. and responded within minutes. The victim had sustained major traumatic injuries to the face and torso. Emergency care was initiated by EMS personnel and the victim was transported to an area hospital where he was pronounced dead at 3:32 p.m. NCOSHA investigators examined road grader #1 (the grader directly involved in the incident). The road grader was manufactured in 1996. According to the construction company owner, he had leased the grader when it was new under a long-term lease from an equipment rental company. He had used the grader for approximately 5 years and had a verbal agreement with the rental company that his company would take responsibility for all minor repairs and servicing which included maintaining or replacing backup alarms. The grader was equipped with a backup alarm (Photo 2). When the backup alarm was tested by NCOSHA and police department investigators on the day of the incident, the alarm emitted no audible signal. The victim's coworker told NCOSHA investigators that he did not hear any warning sounds coming from the grader. Evidence indicates that several pieces of equipment were running near the location of the incident: the pickup truck, grader #1, and a roller, approximately 400 feet away (see Figure 1 for work-site layout). Grader Operator #1 told NCOSHA investigators that he had notified his superiors that the backup alarm was not working properly 2 weeks before the incident, but it had not been replaced. The grader operator told police and NCOSHA investigators that he did not see the workers or their parked pickup truck because the sun was shining in his eyes. Police investigators determined that visibility was nearly impossible when seated in the driver's seat of the grader and looking backward due to the bright setting sun and the dust- and dirt-covered cab windows and mirrors (Photo 3). NCOSHA investigators inspected side mirrors that had been installed on each side of the grader by the equipment lender; they were loose and would not stay in place when adjusted. Grader Operator #2 told NCOSHA investigators that because he was working to the east and at the bottom of a hill in a curved section of the road, he did not see any of the events leading up to the fatal incident. Back to TopCause of DeathThe coroner's report indicated that the cause of death was blunt-force trauma. Recommendations/DiscussionRecommendation #1: Employers should develop, implement, and enforce a comprehensive written safety program for all workers which includes training in hazard recognition and the avoidance of unsafe conditions.Discussion: Given the known hazards associated with road construction (e.g., hazards of being struck by or run over by vehicles and/or equipment), employers should provide their workers with a comprehensive safety program and training that addresses standard operating procedures that are to be followed when working on or near moving vehicles and /or equipment. Safe equipment operation around workers on foot, for example, should include isolating workers on foot from equipment as much as possible, scheduling work tasks to keep workers on foot out of areas where heavy equipment is used, and training workers on foot and equipment operators in appropriate communication methods (e.g., two-way radio, personal one-on-one, hand signals, etc.) that are to be used. Because all workers, including equipment operators and supervisors, are likely to be on foot around operating equipment, all workers should be trained to recognize the hazards of working on foot around equipment. Training should be a vital part of a road construction company's safety program and should address, at a minimum, all known and anticipated hazards. OSHA regulations require employers to train workers to recognize and avoid unsafe conditions that may be present in their work environments (e.g., 29 CFR 1926.21(b)(2). 1 Equipment operators should be trained to operate equipment in accordance with safety rules found in the equipment operator's manual and with safety rules written by the company. They should be trained to never move equipment without first inspecting the area around them and making positive visual contact with any workers on foot near the equipment. If equipment operators cannot see behind them as they back up, they should be trained to stop their machines, dismount, visually examine the area behind their machine and to clear the area of workers and equipment before proceeding. Employers should ensure that equipment operators are trained to examine the cab glass and mirrors on equipment they are using and to clean cab glass and mirrors and adjust their mirrors as needed prior to equipment use. Employers can obtain additional information pertaining to preventing injuries from vehicles and equipment in work zones in a NIOSH document on this topic (DHHS, NIOSH Publication No. 2001-128). 2 Note: Following the incident the company developed an expanded employee policies and safety handbook and distributed it to all workers. The heavy equipment section in the handbook provides a general statement regarding heavy equipment users/use and defines in detail all required procedures for "start-up," "operation" and "shut down." A copy of the heavy equipment procedures is to be kept in all vehicles. Several of the general policy statements address specific issues related to this fatality and include "DO NOT operate any vehicle unless everything is satisfactory. Report any problems to your supervisor immediately and wait for his instruction. Always be aware of your position in relation to other vehicles, equipment, stationary objects, and workers on foot." The handbook provides detailed procedures that are to be followed before operating machines, as follows:
| ||||||||||||
In-house Reports | ||||||||||||