[Code of Federal Regulations]
[Title 49, Volume 2]
[Revised as of October 1, 2007]
From the U.S. Government Printing Office via GPO Access
[CITE: 49CFR172.102]
[Page 333-354]
TITLE 49--TRANSPORTATION
CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION,
DEPARTMENT OF TRANSPORTATION
PART 172_HAZARDOUS MATERIALS TABLE, SPECIAL PROVISIONS, HAZARDOUS
MATERIALS COMMUNICATIONS, EMERGENCY RESPONSE INFORMATION, AND
Subpart B_Table of Hazardous Materials and Special Provisions
Sec. 172.102 Special provisions.
(a) General. When column 7 of the Sec. 172.101 table refers to a
special provision for a hazardous material, the meaning and requirements
of that provision are as set forth in this section. When a special
provision specifies packaging or packaging requirements--
(1) The special provision is in addition to the standard
requirements for all packagings prescribed in Sec. 173.24 of this
subchapter and any other applicable packaging requirements in subparts
[[Page 334]]
A and B of part 173 of this subchapter; and
(2) To the extent a special provision imposes limitations or
additional requirements on the packaging provisions set forth in column
8 of the Sec. 172.101 table, packagings must conform to the
requirements of the special provision.
(b) Description of codes for special provisions. Special provisions
contain packaging provisions, prohibitions, exceptions from requirements
for particular quantities or forms of materials and requirements or
prohibitions applicable to specific modes of transportation, as follows:
(1) A code consisting only of numbers (for example, ``11'') is
multi-modal in application and may apply to bulk and non-bulk
packagings.
(2) A code containing the letter ``A'' refers to a special provision
which applies only to transportation by aircraft.
(3) A code containing the letter ``B'' refers to a special provision
that applies only to bulk packaging requirements. Unless otherwise
provided in this subchapter, these special provisions do not apply to
UN, IM Specification portable tanks or IBCs.
(4) A code containing the letters ``IB'' or ``IP'' refers to a
special provision that applies only to transportation in IBCs.
(5) A code containing the letter ``N'' refers to a special provision
which applies only to non-bulk packaging requirements.
(6) A code containing the letter ``R'' refers to a special provision
which applies only to transportation by rail.
(7) A code containing the letter ``T'' refers to a special provision
which applies only to transportation in UN or IM Specification portable
tanks.
(8) A code containing the letters ``TP'' refers to a portable tank
special provision for UN or IM Specification portable tanks that is in
addition to those provided by the portable tank instructions or the
requirements in part 178 of this subchapter.
(9) A code containing the letter ``W'' refers to a special provision
that applies only to transportation by water.
(c) Tables of special provisions. The following tables list, and set
forth the requirements of, the special provisions referred to in column
7 of the Sec. 172.101 table.
(1) Numeric provisions. These provisions are multi-modal and apply
to bulk and non-bulk packagings:
Code/Special Provisions
1 This material is poisonous by inhalation (see Sec. 171.8 of this
subchapter) in Hazard Zone A (see Sec. 173.116(a) or Sec. 173.133(a)
of this subchapter), and must be described as an inhalation hazard under
the provisions of this subchapter.
2 This material is poisonous by inhalation (see Sec. 171.8 of this
subchapter) in Hazard Zone B (see Sec. 173.116(a) or Sec. 173.133(a)
of this subchapter), and must be described as an inhalation hazard under
the provisions of this subchapter.
3 This material is poisonous by inhalation (see Sec. 171.8 of this
subchapter) in Hazard Zone C (see Sec. 173.116(a) of this subchapter),
and must be described as an inhalation hazard under the provisions of
this subchapter.
4 This material is poisonous by inhalation (see Sec. 171.8 of this
subchapter) in Hazard Zone D (see Sec. 173.116(a) of this subchapter),
and must be described as an inhalation hazard under the provisions of
this subchapter.
5 If this material meets the definition for a material poisonous by
inhalation (see Sec. 171.8 of this subchapter), a shipping name must be
selected which identifies the inhalation hazard, in Division 2.3 or
Division 6.1, as appropriate.
6 This material is poisonous-by-inhalation and must be described as an
inhalation hazard under the provisions of this subchapter.
8 A hazardous substance that is not a hazardous waste may be shipped
under the shipping description ``Other regulated substances, liquid or
solid, n.o.s.'', as appropriate. In addition, for solid materials,
special provision B54 applies.
9 Packaging for certain PCBs for disposal and storage is prescribed by
EPA in 40 CFR 761.60 and 761.65.
11 The hazardous material must be packaged as either a liquid or a
solid, as appropriate, depending on its physical form at 55 [deg]C (131
[deg]F) at atmospheric pressure.
12 In concentrations greater than 40 percent, this material has strong
oxidizing properties and is capable of starting fires in contact with
combustible materials. If appropriate, a package containing this
material must conform to the additional labeling requirements of Sec.
172.402 of this subchapter.
13 The words ``Inhalation Hazard'' shall be entered on each shipping
paper in association with the shipping description, shall be
[[Page 335]]
marked on each non-bulk package in association with the proper shipping
name and identification number, and shall be marked on two opposing
sides of each bulk package. Size of marking on bulk package must conform
to Sec. 172.302(b) of this subchapter. The requirements of Sec. Sec.
172.203(m) and 172.505 of this subchapter do not apply.
14 Motor fuel antiknock mixtures are:
a. Mixtures of one or more organic lead mixtures (such as tetraethyl
lead, triethylmethyl lead, diethyldimethyl lead, ethyltrimethyl lead,
and tetramethyl lead) with one or more halogen compounds (such as
ethylene dibromide and ethylene dichloride), hydrocarbon solvents or
other equally efficient stabilizers; or
b. tetraethyl lead.
15 This entry applies to ``Chemical kits'' and ``First aid kits''
containing one or more compatible items of hazardous materials in boxes,
cases, etc. that, for example, are used for medical, analytical,
diagnostic, testing, or repair purposes. For transportation by aircraft,
materials forbidden for transportation by passenger aircraft or cargo
aircraft may not be included in the kits. Chemical kits and first aid
kits are excepted from the specification packaging requirements of this
subchapter when packaged in combination packagings. Chemical kits and
first aid kits are also excepted from the labeling and placarding
requirements of this subchapter, except when offered for transportation
or transported by air. Chemical and first aid kits may be transported in
accordance with the consumer commodity and ORM exceptions in Sec.
173.156, provided they meet all required conditions. Kits that are
carried on board transport vehicles for first aid or operating purposes
are not subject to the requirements of this subchapter.
16 This description applies to smokeless powder and other solid
propellants that are used as powder for small arms and have been classed
as Division 1.3 and 4.1 in accordance with Sec. 173.56 of this
subchapter.
18 This description is authorized only for fire extinguishers listed in
Sec. 173.309(b) of this subchapter meeting the following conditions:
a. Each fire extinguisher may only have extinguishing contents that
are nonflammable, non-poisonous, non-corrosive and commercially free
from corroding components.
b. Each fire extinguisher must be charged with a nonflammable, non-
poisonous, dry gas that has a dew-point at or below minus 46.7 [deg]C
(minus 52 [deg]F) at 101 kPa (1 atmosphere) and is free of corroding
components, to not more than the service pressure of the cylinder.
c. A fire extinguisher may not contain more than 30% carbon dioxide
by volume or any other corrosive extinguishing agent.
d. Each fire extinguisher must be protected externally by suitable
corrosion-resisting coating.
19 For domestic transportation only, the identification number
``UN1075'' may be used in place of the identification number specified
in column (4) of the Sec. 172.101 table. The identification number used
must be consistent on package markings, shipping papers and emergency
response information.
21 This material must be stabilized by appropriate means (e.g., addition
of chemical inhibitor, purging to remove oxygen) to prevent dangerous
polymerization (see Sec. 173.21(f) of this subchapter).
22 If the hazardous material is in dispersion in organic liquid, the
organic liquid must have a flash point above 50 [deg]C (122 [deg]F).
23 This material may be transported under the provisions of Division 4.1
only if it is so packed that the percentage of diluent will not fall
below that stated in the shipping description at any time during
transport. Quantities of not more than 500 g per package with not less
than 10 percent water by mass may also be classed in Division 4.1,
provided a negative test result is obtained when tested in accordance
with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see
Sec. 171.7 of this subchapter).
24 Alcoholic beverages containing more than 70 percent alcohol by volume
must be transported as materials in Packing Group II. Alcoholic
beverages containing more than 24 percent but not more than 70 percent
alcohol by volume must be transported as materials in Packing Group III.
26 This entry does not include ammonium permanganate, the transport of
which is prohibited except when approved by the Associate Administrator.
28 The dihydrated sodium salt of dichloroisocyanuric acid is not subject
to the requirements of this subchapter.
29 Lithium cells and batteries and equipment containing or packed with
lithium cells and batteries which do not comply with the provisions of
Sec. 173.185 of this subchapter may be transported only if they are
approved by the Associate Administrator.
30 Sulfur is not subject to the requirements of this subchapter if
transported in a non-bulk packaging or if formed to a specific shape
(for example, prills, granules, pellets, pastilles, or flakes). A bulk
packaging containing sulfur is not subject to the placarding
requirements of subpart F of this part, if it is marked with the
appropriate identification number as required by subpart D of this part.
Molten sulfur must be marked as required by Sec. 172.325 of this
subchapter.
[[Page 336]]
31 Materials which have undergone sufficient heat treatment to render
them non-hazardous are not subject to the requirements of this
subchapter.
32 Polymeric beads and molding compounds may be made from polystyrene,
poly(methyl methacrylate) or other polymeric material.
33 Ammonium nitrites and mixtures of an inorganic nitrite with an
ammonium salt are prohibited.
34 The commercial grade of calcium nitrate fertilizer, when consisting
mainly of a double salt (calcium nitrate and ammonium nitrate)
containing not more than 10 percent ammonium nitrate and at least 12
percent water of crystallization, is not subject to the requirements of
this subchapter.
35 Antimony sulphides and oxides which do not contain more than 0.5
percent of arsenic calculated on the total mass do not meet the
definition of Division 6.1.
36 The maximum net quantity per package is 5 L (1 gallon) or 5 kg (11
pounds).
37 Unless it can be demonstrated by testing that the sensitivity of the
substance in its frozen state is no greater than in its liquid state,
the substance must remain liquid during normal transport conditions. It
must not freeze at temperatures above -15 [deg]C (5 [deg]F).
38 If this material shows a violent effect in laboratory tests involving
heating under confinement, the labeling requirements of Special
Provision 53 apply, and the material must be packaged in accordance with
packing method OP6 in Sec. 173.225 of this subchapter. If the SADT of
the technically pure substance is higher than 75 [deg]C, the technically
pure substance and formulations derived from it are not self-reactive
materials and, if not meeting any other hazard class, are not subject to
the requirements of this subchapter.
39 This substance may be carried under provisions other than those of
Class 1 only if it is so packed that the percentage of water will not
fall below that stated at any time during transport. When phlegmatized
with water and inorganic inert material, the content of urea nitrate
must not exceed 75 percent by mass and the mixture should not be capable
of being detonated by test 1(a)(i) or test 1(a)(ii) in the UN Manual of
Tests and Criteria (IBR, see Sec. 171.7 of this subchapter).
40 Polyester resin kits consist of two components: a base material
(Class 3, Packing Group II or III) and an activator (organic peroxide),
each separately packed in an inner packaging. The organic peroxide must
be type D, E, or F, not requiring temperature control, and be limited to
a quantity of 125 mL (4.22 ounces) per inner packaging if liquid, and
500 g (1 pound) if solid. The components may be placed in the same outer
packaging provided they will not interact dangerously in the event of
leakage. Packing group will be II or III, according to the criteria for
Class 3, applied to the base material.
43 The membrane filters, including paper separators and coating or
backing materials, that are present in transport, must not be able to
propagate a detonation as tested by one of the tests described in the UN
Manual of Tests and Criteria, Part I, Test series 1(a) (IBR, see Sec.
171.7 of this subchapter). On the basis of the results of suitable
burning rate tests, and taking into account the standard tests in the UN
Manual of Tests and Criteria, Part III, subsection 33.2.1 (IBR, see
Sec. 171.7 of this subchapter), nitrocellulose membrane filters in the
form in which they are to be transported that do not meet the criteria
for a Division 4.1 material are not subject to the requirements of this
subchapter. Packagings must be so constructed that explosion is not
possible by reason of increased internal pressure. Nitrocellulose
membrane filters covered by this entry, each with a mass not exceeding
0.5 g, are not subject to the requirements of this subchapter when
contained individually in an article or a sealed packet.
44 The formulation must be prepared so that it remains homogenous and
does not separate during transport. Formulations with low nitrocellulose
contents and neither showing dangerous properties when tested for their
ability to detonate, deflagrate or explode when heated under defined
confinement by the appropriate test methods and criteria in the UN
Manual of Tests and Criteria (IBR, see Sec. 171.7 of this subchapter),
nor classed as a Division 4.1 (flammable solid) when tested in
accordance with the procedures specified in Sec. 173.124 of this
subchapter (chips, if necessary, crushed and sieved to a particle size
of less than 1.25 mm), are not subject to the requirements of this
subchapter.
45 Temperature should be maintained between 18 [deg]C (64.4 [deg]F) and
40 [deg]C (104 [deg]F). Tanks containing solidified methacrylic acid
must not be reheated during transport.
46 This material must be packed in accordance with packing method OP6
(see Sec. 173.225 of this subchapter). During transport, it must be
protected from direct sunshine and stored (or kept) in a cool and well-
ventilated place, away from all sources of heat.
47 Mixtures of solids that are not subject to this subchapter and
flammable liquids may be transported under this entry without first
applying the classification criteria of Division 4.1, provided there is
no free liquid visible at the time the material is loaded or at the time
the packaging or transport unit is closed. Except when the liquids are
fully absorbed in solid material contained
[[Page 337]]
in sealed bags, each packaging must correspond to a design type that has
passed a leakproofness test at the Packing Group II level. Small inner
packagings consisting of sealed packets and articles containing less
than 10 mL of a Class 3 liquid in Packing Group II or III absorbed onto
a solid material are not subject to this subchapter provided there is no
free liquid in the packet or article.
48 Mixtures of solids which are not subject to this subchapter and toxic
liquids may be transported under this entry without first applying the
classification criteria of Division 6.1, provided there is no free
liquid visible at the time the material is loaded or at the time the
packaging or transport unit is closed. Each packaging must correspond to
a design type that has passed a leakproofness test at the Packing Group
II level. This entry may not be used for solids containing a Packing
Group I liquid.
49 Mixtures of solids which are not subject to this subchapter and
corrosive liquids may be transported under this entry without first
applying the classification criteria of Class 8, provided there is no
free liquid visible at the time the material is loaded or at the time
the packaging or transport unit is closed. Each packaging must
correspond to a design type that has passed a leakproofness test at the
Packing Group II level.
50 Cases, cartridge, empty with primer which are made of metallic or
plastic casings and meeting the classification criteria of Division 1.4
are not regulated for domestic transportation.
51 This description applies to items previously described as ``Toy
propellant devices, Class C'' and includes reloadable kits. Model rocket
motors containing 30 grams or less propellant are classed as Division
1.4S and items containing more than 30 grams of propellant but not more
than 62.5 grams of propellant are classed as Division 1.4C.
52 This entry may only be used for substances that do not exhibit
explosive properties of Class 1 (explosive) when tested in accordance
with Test Series 1 and 2 of Class 1 (explosive) in the UN Manual of
Tests and Criteria, Part I (incorporated by reference; see Sec. 171.7
of this subchapter).
53 Packages of these materials must bear the subsidiary risk label,
``EXPLOSIVE'', and the subsidiary hazard class/division must be entered
in parentheses immediately following the primary hazard class in the
shipping description, unless otherwise provided in this subchapter or
through an approval issued by the Associate Administrator, or the
competent authority of the country of origin. A copy of the approval
shall accompany the shipping papers.
54 Maneb or maneb preparations not meeting the definition of Division
4.3 or any other hazard class are not subject to the requirements of
this subchapter when transported by motor vehicle, rail car, or
aircraft.
55 This device must be approved in accordance with Sec. 173.56 of this
subchapter by the Associate Administrator.
56 A means to interrupt and prevent detonation of the detonator from
initiating the detonating cord must be installed between each electric
detonator and the detonating cord ends of the jet perforating guns
before the charged jet perforating guns are offered for transportation.
57 Maneb or Maneb preparations stabilized against self-heating need not
be classified in Division 4.2 when it can be demonstrated by testing
that a volume of 1 m\3\ of substance does not self-ignite and that the
temperature at the center of the sample does not exceed 200 [deg]C, when
the sample is maintained at a temperature of not less than 75 [deg]C
2 [deg]C for a period of 24 hours, in accordance
with procedures set forth for testing self-heating materials in the UN
Manual of Tests and Criteria (IBR, see Sec. 171.7 of this subchapter).
58 Aqueous solutions of Division 5.1 inorganic solid nitrate substances
are considered as not meeting the criteria of Division 5.1 if the
concentration of the substances in solution at the minimum temperature
encountered in transport is not greater than 80% of the saturation
limit.
59 Ferrocerium, stabilized against corrosion, with a minimum iron
content of 10 percent is not subject to the requirements of this
subchapter.
60 After September 30, 1997, an oxygen generator, chemical, that is
shipped with its means of initiation attached must incorporate at least
two positive means of preventing unintentional actuation of the
generator, and be classed and approved by the Associate Administrator.
The procedures for approval of a chemical oxygen generator that contains
an explosive means of initiation (e.g., a primer or electric match) are
specified in Sec. 173.56 of this subchapter. Each person who offers a
chemical oxygen generator for transportation after September 30, 1997,
shall: (1) ensure that it is offered in conformance with the conditions
of the approval; (2) maintain a copy of the approval at each facility
where the chemical oxygen generator is packaged; and (3) mark the
approval number on the outside of the package.
61 A chemical oxygen generator is spent if its means of ignition and all
or a part of its chemical contents have been expended.
64 The group of alkali metals includes lithium, sodium, potassium,
rubidium, and caesium.
[[Page 338]]
65 The group of alkaline earth metals includes magnesium, calcium,
strontium, and barium.
66 Formulations of these substances containing not less than 30 percent
non-volatile, non-flammable phlegmatizer are not subject to this
subchapter.
70 Black powder that has been classed in accordance with the
requirements of Sec. 173.56 of this subchapter may be reclassed and
offered for domestic transportation as a Division 4.1 material if it is
offered for transportation and transported in accordance with the
limitations and packaging requirements of Sec. 173.170 of this
subchapter.
74 During transport, this material must be protected from direct
sunshine and stored or kept in a cool and well-ventilated place, away
from all sources of heat.
77 Mixtures containing not more than 23.5% oxygen by volume may be
transported under this entry when no other oxidizing gases are present.
A Division 5.1 subsidiary risk label is not required if this special
provision applies.
78 This entry may not be used to describe compressed air which contains
more than 23.5 percent oxygen. An oxidizer label is not required for any
oxygen concentration of 23.5 percent or less.
79 This entry may not be used for mixtures that meet the definition for
oxidizing gas.
81 Polychlorinated biphenyl items, as defined in 40 CFR 761.3, for which
specification packagings are impractical, may be packaged in non-
specification packagings meeting the general packaging requirements of
subparts A and B of part 173 of this subchapter. Alternatively, the item
itself may be used as a packaging if it meets the general packaging
requirements of subparts A and B of part 173 of this subchapter.
102 The ends of the detonating cord must be tied fast so that the
explosive cannot escape. The articles may be transported as in Division
1.4 Compatibility Group D (1.4D) if all of the conditions specified in
Sec. 173.63(a) of this subchapter are met.
103 Detonators which will not mass detonate and undergo only limited
propagation in the shipping package may be assigned to 1.4B
classification code. Mass detonate means that more than 90 percent of
the devices tested in a package explode practically simultaneously.
Limited propagation means that if one detonator near the center of a
shipping package is exploded, the aggregate weight of explosives,
excluding ignition and delay charges, in this and all additional
detonators in the outside packaging that explode may not exceed 25
grams.
105 The word ``Agents'' may be used instead of ``Explosives'' when
approved by the Associate Administrator.
106 The recognized name of the particular explosive may be specified in
addition to the type.
107 The classification of the substance is expected to vary especially
with the particle size and packaging but the border lines have not been
experimentally determined; appropriate classifications should be
verified following the test procedures in Sec. Sec. 173.57 and 173.58
of this subchapter.
108 Fireworks must be so constructed and packaged that loose pyrotechnic
composition will not be present in packages during transportation.
109 Rocket motors must be nonpropulsive in transportation unless
approved in accordance with Sec. 173.56 of this subchapter. A rocket
motor to be considered ``nonpropulsive'' must be capable of unrestrained
burning and must not appreciably move in any direction when ignited by
any means.
110 Fire extinguishers transported under UN1044 may include installed
actuating cartridges (cartridges, power device of Division 1.4C or
1.4S), without changing the classification of Division 2.2, provided the
aggregate quantity of deflagrating (propellant) explosives does not
exceed 3.2 grams per extinguishing unit.
111 Explosive substances of Division 1.1 Compatibility Group A (1.1A)
are forbidden for transportation if dry or not desensitized, unless
incorporated in a device.
113 The sample must be given a tentative approval by an agency or
laboratory in accordance with Sec. 173.56 of this subchapter.
114 Jet perforating guns, charged, oil well, without detonator may be
reclassed to Division 1.4 Compatibility Group D (1.4D) if the following
conditions are met:
a. The total weight of the explosive contents of the shaped charges
assembled in the guns does not exceed 90.5 kg (200 pounds) per vehicle;
and
b. The guns are packaged in accordance with Packing Method US 1 as
specified in Sec. 173.62 of this subchapter.
115 Boosters with detonator, detonator assemblies and boosters with
detonators in which the total explosive charge per unit does not exceed
25 g, and which will not mass detonate and undergo only limited
propagation in the shipping package may be assigned to 1.4B
classification code. Mass detonate means more than 90 percent of the
devices tested in a package explode practically simultaneously. Limited
propagation means that if one booster near the center of the package is
exploded, the aggregate weight of explosives, excluding ignition and
delay charges, in this and all additional boosters in the outside
packaging that explode may not exceed 25 g.
116 Fuzes, detonating may be classed in Division 1.4 if the fuzes do not
contain more than 25 g of explosive per fuze and are made and packaged
so that they will not
[[Page 339]]
cause functioning of other fuzes, explosives or other explosive devices
if one of the fuzes detonates in a shipping packaging or in adjacent
packages.
117 If shipment of the explosive substance is to take place at a time
that freezing weather is anticipated, the water contained in the
explosive substance must be mixed with denatured alcohol so that
freezing will not occur.
118 This substance may not be transported under the provisions of
Division 4.1 unless specifically authorized by the Associate
Administrator.
119 This substance, when in quantities of not more than 11.5 kg (25.3
pounds), with not less than 10 percent water, by mass, also may be
classed as Division 4.1, provided a negative test result is obtained
when tested in accordance with test series 6(c) of the UN Manual of
Tests and Criteria (IBR, see Sec. 171.7 of this subchapter).
120 The phlegmatized substance must be significantly less sensitive than
dry PETN.
121 This substance, when containing less alcohol, water or phlegmatizer
than specified, may not be transported unless approved by the Associate
Administrator.
123 Any explosives, blasting, type C containing chlorates must be
segregated from explosives containing ammonium nitrate or other ammonium
salts.
125 Lactose or glucose or similar materials may be used as a
phlegmatizer provided that the substance contains not less than 90%, by
mass, of phlegmatizer. These mixtures may be classified in Division 4.1
when tested in accordance with test series 6(c) of the UN Manual of
Tests and Criteria (IBR, see Sec. 171.7 of this subchapter) and
approved by the Associate Administrator. Testing must be conducted on at
least three packages as prepared for transport. Mixtures containing at
least 98%, by mass, of phlegmatizer are not subject to the requirements
of this subchapter. Packages containing mixtures with not less than 90%
by mass, of phlegmatizer need not bear a POISON subsidiary risk label.
127 Mixtures containing oxidizing and organic materials transported
under this entry may not meet the definition and criteria of a Class 1
material. (See Sec. 173.50 of this subchapter.)
128 Regardless of the provisions of Sec. 172.101(c)(12), aluminum
smelting by-products and aluminum remelting by-products described under
this entry, meeting the definition of Class 8, Packing Group II and III
may be classed as a Division 4.3 material and transported under this
entry. The presence of a Class 8 hazard must be communicated as required
by this Part for subsidiary hazards.
129 These materials may not be classified and transported unless
authorized by the Associate Administrator on the basis of results from
Series 2 Test and a Series 6(c) Test from the UN Manual of Tests and
Criteria (IBR, see Sec. 171.7 of this subchapter) on packages as
prepared for transport. The packing group assignment and packaging must
be approved by the Associate Administrator for Hazardous Materials
Safety on the basis of the criteria in Sec. 173.21 of this subchapter
and the package type used for the Series 6(c) test.
130 For other than a dry battery specifically covered by another entry
in the Sec. 172.101 Table, ``Batteries, dry'' are not subject to the
requirements of this subchapter when they are securely packaged and
offered for transportation in a manner that prevents the dangerous
evolution of heat (for example, by the effective insulation of exposed
terminals) and protects against short circuits.
131 This material may not be offered for transportation unless approved
by the Associate Administrator.
132 This entry may only be used for uniform, ammonium nitrate based
fertilizer mixtures, containing nitrogen, phosphate or potash, meeting
the following criteria: (1) Contains not more than 70% ammonium nitrate
and not more than 0.4% total combustible, organic material calculated as
carbon or (2) Contains not more than 45% ammonium nitrate and
unrestricted combustible material.
134 This entry only applies to vehicles, machinery and equipment powered
by wet batteries, sodium batteries, or lithium batteries that are
transported with these batteries installed. Examples of such items are
electrically-powered cars, lawn mowers, wheelchairs, and other mobility
aids. Self-propelled vehicles that also contain an internal combustion
engine must be consigned under the entry ``Vehicle, flammable gas
powered'' or ``Vehicle, flammable liquid powered'', as appropriate.
Except as provided in Special Provision A102, vehicles, machinery and
equipment powered by primary lithium batteries that are transported with
these batteries installed are forbidden aboard passenger-carrying
aircraft.
135 The entries ``Vehicle, flammable gas powered'' or ``Vehicle,
flammable liquid powered,'' as appropriate, must be used when internal
combustion engines are installed in a vehicle. These entries include
hybrid electric vehicles powered by both an internal combustion engine
and batteries.
136 This entry only applies to machinery and apparatus containing
hazardous materials as in integral element of the machinery or
apparatus. It may not be used to describe machinery or apparatus for
which a proper shipping name exists in the Sec. 172.101
[[Page 340]]
Table. Except when approved by the Associate Administrator, machinery or
apparatus may only contain hazardous materials for which exceptions are
referenced in Column (8) of the Sec. 172.101 Table and are provided in
part 173, subpart D, of this subchapter. Hazardous materials shipped
under this entry are excepted from the labeling requirements of this
subchapter unless offered for transportation or transported by aircraft
and are not subject to the placarding requirements of part 172, subpart
F, of this subchapter. Orientation markings as described in Sec.
172.312 (a)(2) are required when liquid hazardous materials may escape
due to incorrect orientation. The machinery or apparatus, if unpackaged,
or the packaging in which it is contained shall be marked ``Dangerous
goods in machinery'' or ``Dangerous goods in apparatus'', as
appropriate, with the identification number UN3363. For transportation
by aircraft, machinery or apparatus may not contain any material
forbidden for transportation by passenger or cargo aircraft. The
Associate Administrator may except from the requirements of this
subchapter, equipment, machinery and apparatus provided:
a. It is shown that it does not pose a significant risk in
transportation;
b. The quantities of hazardous materials do not exceed those
specified in Sec. 173.4 of this subchapter; and
c. The equipment, machinery or apparatus conforms with Sec. 173.222
of this subchapter.
137 Cotton, dry; flax, dry; and sisal, dry are not subject to the
requirements of this subchapter when they are baled in accordance with
ISO 8115, ``Cotton Bales--Dimensions and Density'' (IBR, see Sec. 171.7
of this subchapter) to a density of not less than 360 kg/m\3\ (22.1 lb/
ft\3\) for cotton, 400 kg/m\3\ (24.97 lb/ft\3\) for flax and 620 kg/m\3\
(38.71 lb/ft\3\) for sisal and transported in a freight container or
closed transport vehicle.
138 Lead compounds which, when mixed in a ratio of 1:1000 with 0.07M
(Molar concentration) hydrochloric acid and stirred for one hour at a
temperature of 23 [deg]C 2 [deg]C, exhibit a
solubility of 5% or less are considered insoluble.
139 Use of the ``special arrangement'' proper shipping names for
international shipments must be made under an IAEA Certificate of
Competent Authority issued by the Associate Administrator in accordance
with the requirements in Sec. 173.471, Sec. 173.472, or Sec. 173.473
of this subchapter. Use of these proper shipping names for domestic
shipments may be made only under a DOT special permit, as defined in,
and in accordance with the requirements of subpart B of part 107 of this
subchapter.
140 This material is regulated only when it meets the defining criteria
for a hazardous substance or a marine pollutant. In addition, the column
5 reference is modified to read ``III'' on those occasions when this
material is offered for transportation or transported by highway or
rail.
141 A toxin obtained from a plant, animal, or bacterial source
containing an infectious substance, or a toxin contained in an
infectious substance, must be classed as Division 6.2, described as an
infectious substance, and assigned to UN 2814 or UN 2900, as
appropriate.
142 These hazardous materials may not be classified and transported
unless authorized by the Associate Administrator. The Associate
Administrator will base the authorization on results from Series 2 tests
and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR,
see Sec. 171.7 of this subchapter) on packages as prepared for
transport in accordance with the requirements of this subchapter.
144 If transported as a residue in an underground storage tank (UST), as
defined in 40 CFR 280.12, that has been cleaned and purged or rendered
inert according to the American Petroleum Institute (API) Standard 1604
(IBR, see Sec. 171.7 of this subchapter), then the tank and this
material are not subject to any other requirements of this subchapter.
However, sediments remaining in the tank that meet the definition for a
hazardous material are subject to the applicable regulations of this
subchapter.
145 This entry applies to formulations that neither detonate in the
cavitated state nor deflagrate in laboratory testing, show no effect
when heated under confinement, exhibit no explosive power, and are
thermally stable (self-accelerating decomposition temperature (SADT) at
60 [deg]C (140 [deg]F) or higher for a 50 kg (110.2 lbs.) package).
Formulations not meeting these criteria must be transported under the
provisions applicable to the appropriate entry in the Organic Peroxide
Table in Sec. 173.225 of this subchapter.
146 This description may be used for a material that poses a hazard to
the environment but does not meet the definition for a hazardous waste
or a hazardous substance, as defined in Sec. 171.8 of this subchapter,
or any hazard class, as defined in part 173 of this subchapter, if it is
designated as environmentally hazardous by another Competent Authority.
This provision may be used for both domestic and international
shipments.
147 This entry applies to non-sensitized emulsions, suspensions, and
gels consisting primarily of a mixture of ammonium nitrate and fuel,
intended to produce a Type E blasting explosive only after further
processing prior to use. The mixture for emulsions typically has the
following composition: 60-85% ammonium nitrate; 5-30%
[[Page 341]]
water; 2-8% fuel; 0.5-4% emulsifier or thickening agent; 0-10% soluble
flame suppressants; and trace additives. Other inorganic nitrate salts
may replace part of the ammonium nitrate. The mixture for suspensions
and gels typically has the following composition: 60-85% ammonium
nitrate; 0-5% sodium or potassium perchlorate; 0-17% hexamine nitrate or
monomethylamine nitrate; 5-30% water; 2-15% fuel; 0.5-4% thickening
agent; 0-10% soluble flame suppressants; and trace additives. Other
inorganic nitrate salts may replace part of the ammonium nitrate. These
substances must satisfactorily pass Test Series 8 of the UN Manual of
Tests and Criteria, Part I, Section 18 (IBR, see Sec. 171.7 of this
subchapter), and may not be classified and transported unless approved
by the Associate Administrator.
149 When transported as a limited quantity or a consumer commodity, the
maximum net capacity specified in Sec. 173.150(b)(2) of this subchapter
for inner packagings may be increased to 5 L (1.3 gallons).
150 This description may be used only for uniform mixtures of
fertilizers containing ammonium nitrate as the main ingredient within
the following composition limits:
a. Not less than 90% ammonium nitrate with not more than 0.2% total
combustible, organic material calculated as carbon, and with added
matter, if any, that is inorganic and inert when in contact with
ammonium nitrate; or
b. Less than 90% but more than 70% ammonium nitrate with other
inorganic materials, or more than 80% but less than 90% ammonium nitrate
mixed with calcium carbonate and/or dolomite, and not more than 0.4%
total combustible, organic material calculated as carbon; or
c. Ammonium nitrate-based fertilizers containing mixtures of
ammonium nitrate and ammonium sulphate with more than 45% but less than
70% ammonium nitrate, and not more than 0.4% total combustible, organic
material calculated as carbon such that the sum of the percentage of
compositions of ammonium nitrate and ammonium sulphate exceeds 70%.
151 If this material meets the definition of a flammable liquid in Sec.
173.120 of this subchapter, a FLAMMABLE LIQUID label is also required
and the basic description on the shipping paper must indicate the Class
3 subsidiary hazard.
155 Fish meal or fish scrap may not be transported if the temperature at
the time of loading either exceeds 35 [deg]C (95 [deg]F), or exceeds 5
[deg]C (41 [deg]F) above the ambient temperature, whichever is higher.
156 Asbestos that is immersed or fixed in a natural or artificial binder
material, such as cement, plastic, asphalt, resins or mineral ore, or
contained in manufactured products is not subject to the requirements of
this subchapter.
157 This entry includes hybrid electric vehicles powered by both an
internal combustion engine and wet, sodium or lithium batteries
installed. Vehicles containing an internal combustion engine must be
consigned under the entry ``Vehicle, flammable gas powered'' or
``Vehicle, flammable liquid powered'', as appropriate. Except as
provided in Special Provision A102, vehicles powered by primary lithium
batteries, that are transported with these batteries installed are
forbidden aboard passenger-carrying aircraft.
159 This material must be protected from direct sunshine and kept in a
cool, well-ventilated place away from sources of heat.
160 This entry applies to articles that are used as life-saving vehicle
air bag inflators, air bag modules or seat-belt pretensioners containing
Class 1 (explosive) materials or materials of other hazard classes. Air
bag inflators and modules must be tested in accordance with Test series
6(c) of Part I of the UN Manual of Tests and Criteria (incorporated by
reference; see Sec. 171.7 of this subchapter), with no explosion of the
device, no fragmentation of device casing or pressure vessel, and no
projection hazard or thermal effect that would significantly hinder
fire-fighting or other emergency response efforts in the immediate
vicinity. If the air bag inflator unit satisfactorily passes the series
6(c) test, it is not necessary to repeat the test on the air bag module.
161 For domestic transport, air bag inflators, air bag modules or seat
belt pretensioners that meet the criteria for a Division 1.4G explosive
must be transported using the description, ``Articles, pyrotechnic for
technical purposes,'' UN0431.
162 This material may be transported under the provisions of Division
4.1 only if it is packed so that at no time during transport will the
percentage of diluent fall below the percentage that is stated in the
shipping description.
163 Substances must satisfactorily pass Test Series 8 of the UN Manual
of Tests and Criteria, Part I, Section 18 (IBR, see Sec. 171.7 of this
subchapter).
164 Substances must not be transported under this entry unless approved
by the Associate Administrator on the basis of the results of
appropriate tests according to Part I of the UN Manual of Tests and
Criteria (IBR, see Sec. 171.7 of this subchapter). The material must be
packaged so that the percentage of diluent does not fall below that
stated in the approval at any time during transportation.
165 These substances are susceptible to exothermic decomposition at
elevated temperatures. Decomposition can be initiated by heat, moisture
or by impurities (e.g.,
[[Page 342]]
powdered metals (iron, manganese, cobalt, magnesium)). During the course
of transportation, these substances must be shaded from direct sunlight
and all sources of heat and be placed in adequately ventilated areas.
166 When transported in non-friable tablet form, calcium hypochlorite,
dry, may be transported as a Packing Group III material.
167 These storage systems shall always be considered as containing
hydrogen.
168 For lighters containing a Division 2.1 gas (see Sec. 171.8 of this
subchapter), representative samples of each new lighter design must be
examined and successfully tested as specified in Sec. 173.308(b)(3).
For criteria in determining what is a new lighter design, see Sec.
173.308(b)(1). For transportation of new lighter design samples for
examination and testing, see Sec. 173.308(b)(2). The examination and
testing of each lighter design must be performed by a person authorized
by the Associate Administrator under the provisions of subpart E of part
107 of this chapter, as specified in Sec. 173.308(a)(4). For continued
use of approvals dated prior to January 1, 2012, see Sec.
173.308(b)(5).
For non-pressurized lighters containing a Class 3 (flammable liquid)
material, its design, description, and packaging must be approved by the
Associate Administrator prior to being offered for transportation or
transported in commerce. In addition, a lighter design intended to
contain a non-pressurized Class 3 material is excepted from the
examination and testing criteria specified in Sec. 173.308(b)(3). An
unused lighter or a lighter that is cleaned of residue and purged of
vapors is not subject to the requirements of this subchapter.
169 This entry applies to lighter refills (see Sec. 171.8 of this
subchapter) that contain a Division 2.1 (flammable) gas but do not
contain an ignition device. Lighter refills offered for transportation
under this entry may not exceed 4 fluid ounces capacity (7.22 cubic
inches) or contain more than 65 grams of fuel. A lighter refill
exceeding 4 fluid ounces capacity (7.22 cubic inches) or containing more
than 65 grams of fuel must be classed as a Division 2.1 material,
described with the proper shipping name appropriate for the material,
and packaged in the packaging specified in part 173 of this subchapter
for the flammable gas contained therein. In addition, a container
exceeding 4 fluid ounces volumetric capacity (7.22 cubic inches) or
containing more than 65 grams of fuel may not be connected or manifolded
to a lighter or similar device and must also be described and packaged
according to the fuel contained therein. For transportation by
passenger-carrying aircraft, the net mass of lighter refills may not
exceed 1 kg per package, and, for cargo-only aircraft, the net mass of
lighter refills may not exceed 15 kg per package. See Sec. 173.306(h)
of this subchapter.
170 Air must be eliminated from the vapor space by nitrogen or other
means.
171 This entry may only be used when the material is transported in non-
friable tablet form or for granular or powered mixtures that have been
shown to meet the PG III criteria in Sec. 173.127.
172 This entry includes alcohol mixtures containing up to 5% petroleum
products.
173 An appropriate generic entry may be used for this material.
175 This substance must be stabilized when in concentrations of not more
than 99%.
(2) ``A'' codes. These provisions apply only to transportation by
aircraft:
Code/Special Provisions
A1 Single packagings are not permitted on passenger aircraft.
A2 Single packagings are not permitted on aircraft.
A3 For combination packagings, if glass inner packagings (including
ampoules) are used, they must be packed with absorbent material in
tightly closed metal receptacles before packing in outer packagings.
A4 Liquids having an inhalation toxicity of Packing Group I are not
permitted on aircraft.
A5 Solids having an inhalation toxicity of Packing Group I are not
permitted on passenger aircraft and may not exceed a maximum net
quantity per package of 15 kg (33 pounds) on cargo aircraft.
A6 For combination packagings, if plastic inner packagings are used,
they must be packed in tightly closed metal receptacles before packing
in outer packagings.
A7 Steel packagings must be corrosion-resistant or have protection
against corrosion.
A8 For combination packagings, if glass inner packagings (including
ampoules) are used, they must be packed with cushioning material in
tightly closed metal receptacles before packing in outer packagings.
A9 For combination packagings, if plastic bags are used, they must be
packed in tightly closed metal receptacles before packing in outer
packagings.
A10 When aluminum or aluminum alloy construction materials are used,
they must be resistant to corrosion.
A11 For combination packagings, when metal inner packagings are
permitted, only specification cylinders constructed of metals which are
compatible with the hazardous material may be used.
A13 Bulk packagings are not authorized for transportation by aircraft.
A14 This material is not authorized to be transported as a limited
quantity or consumer commodity in accordance with
[[Page 343]]
Sec. 173.306 of this subchapter when transported aboard an aircraft.
A19 Combination packagings consisting of outer fiber drums or plywood
drums, with inner plastic packagings, are not authorized for
transportation by aircraft.
A20 Plastic bags as inner receptacles of combination packagings are not
authorized for transportation by aircraft.
A29 Combination packagings consisting of outer expanded plastic boxes
with inner plastic bags are not authorized for transportation by
aircraft.
A30 Ammonium permanganate is not authorized for transportation on
aircraft.
A34 Aerosols containing a corrosive liquid in Packing Group II charged
with a gas are not permitted for transportation by aircraft.
A35 This includes any material which is not covered by any of the other
classes but which has an anesthetic, narcotic, noxious or other similar
properties such that, in the event of spillage or leakage on an
aircraft, extreme annoyance or discomfort could be caused to crew
members so as to prevent the correct performance of assigned duties.
A37 This entry applies only to a material meeting the definition in
Sec. 171.8 of this subchapter for self-defense spray.
A51 When transported by cargo-only aircraft, an oxygen generator must
conform to the provisions of an approval issued under Special Provision
60 and be contained in a packaging prepared and originally offered for
transportation by the approval holder.
A52 A cylinder containing Oxygen, compressed, may not be loaded into a
passenger-carrying aircraft or into an inaccessible cargo location on a
cargo-only aircraft unless it is placed in an overpack or outer
packaging that conforms to the performance criteria of Air Transport
Association (ATA) Specification No. 300 (IBR, see Sec. 171.7 of this
subchapter) for Category I shipping containers.
A53 Refrigerating machines and refrigerating machine components are not
subject to the requirements of this subchapter when containing less than
12 kg (26.4 pounds) of a non-flammable gas or when containing 12 L (3
gallons) or less of ammonia solution (UN2672) (see Sec. 173.307 of this
subchapter).
A54 Lithium batteries or lithium batteries contained or packed with
equipment that exceed the maximum gross weight allowed by Column (9B) of
the Sec. 172.101 Table may only be transported on cargo aircraft if
approved by the Associate Administrator.
A55 Prototype lithium batteries and cells that are packed with not more
than 24 cells or 12 batteries per packaging that have not completed the
test requirements in Sub-section 38.3 of the UN Manual of Tests and
Criteria (incorporated by reference; see Sec. 171.7 of this subchapter)
may be transported by cargo aircraft if approved by the Associate
Administrator and provided the following requirements are met:
a. The cells and batteries must be transported in rigid outer
packagings that conform to the requirements of Part 178 of this
subchapter at the Packing Group I performance level; and
b. Each cell and battery must be protected against short circuiting,
must be surrounded by cushioning material that is non-combustible and
non-conductive, and must be individually packed in an inner packaging
that is placed inside an outer specification packaging.
A56 Radioactive material with a subsidiary hazard of Division 4.2,
Packing Group I, must be transported in Type B packages when offered for
transportation by aircraft. Radioactive material with a subsidiary
hazard of Division 2.1 is forbidden from transport on passenger
aircraft.
A59 Sterilization devices, when containing less than 30 mL per inner
packaging with no more than 300 mL per outer packaging may be
transported in accordance with provisions in Sec. 173.4(a)(11)(i). In
addition, after filling, each inner packaging must be determined to be
leak-tight by placing the inner packaging in a hot water bath at a
temperature and for a period of time sufficient to ensure an internal
pressure equal to the vapor pressure of ethylene oxide at 55 [deg]C is
achieved. Any inner packaging showing evidence of leakage, distortion or
other defect under this test may not be transported under the terms of
this special provision. In addition to the packaging required in Sec.
173.4, inner packagings must be placed in a sealed plastic bag
compatible with ethylene oxide and capable of containing the contents in
the event of breakage or leakage of the inner packaging. Glass inner
packagings must be placed within a protective shield capable of
preventing the glass from puncturing the plastic bag in the event of
damage to the packaging (e.g., crushing).
A60 Articles such as sterilization devices, UN2014, Hydrogen peroxide,
aqueous solutions with more than 40 percent but not more than 60 percent
hydrogen peroxide (stabilized as necessary), when containing less than
30 mL per inner packaging with not more than 150 mL per outer packaging,
may be transported in accordance with the provisions in Sec. 173.4,
irrespective of Sec. 173.4(a)(11)(i), provided such packagings were
first subjected to comparative fire testing. Comparative fire testing
must show no difference in burning rate between a package as prepared
for transport (including the substance to be transported) and an
identical package filled with water.
[[Page 344]]
A82 The quantity limits in columns (9A) and (9B) do not apply to human
or animal body parts, whole organs or whole bodies known to contain or
suspected of containing an infectious substance.
A100 Primary (non-rechargeable) lithium batteries and cells are
forbidden for transport aboard passenger carrying aircraft. Secondary
(rechargeable) lithium batteries and cells are authorized aboard
passenger carrying aircraft in packages that do not exceed a gross
weight of 5 kg.
A101 A primary (non-rechargeable) lithium battery or cell packed
with equipment is forbidden for transport aboard a passenger carrying
aircraft unless:
a. The battery or cell complies with the requirements and
limitations of Sec. 173.185(b)(1), (b)(2), (b)(3), (b)(4) and (b)(6) or
Sec. 173.185(c)(1), (c)(2), (c)(3) and (c)(5) of this subchapter;
b. The package contains no more than the number of lithium batteries
or cells necessary to power the intended piece of equipment;
c. The equipment and the battery or cell are packed in a strong
packaging;
d. The net weight of the lithium batteries in the package does not
exceed 5 kg. Packages complying with the requirements of this special
provision are excepted from all other requirements of this subchapter.
A102 A primary (non-rechargeable) lithium battery or cell contained in
equipment is forbidden for transport aboard a passenger carrying
aircraft unless:
a. The battery or cell complies with the requirements and
limitations of Sec. 173.185(b)(1), (b)(2), (b)(3), (b)(4) and (b)(6) or
Sec. 173.185(c)(1), (c)(2), (c)(3) and (c)(5) of this subchapter;
b. The package contains no more than the number of lithium batteries
or cells necessary to power the intended piece of equipment;
c. The equipment containing the battery or cell is packed in strong
packagings; and
d. The net weight of the package does not exceed 5 kg. Packages
complying with the requirements of this special provision are excepted
from all other requirements of this subchapter.
A103 A secondary (rechargeable) lithium battery or cell packed with
equipment is authorized aboard passenger carrying aircraft in packages
that do not exceed a gross weight of 5 kg.
A104 A secondary (rechargeable) lithium battery or cell packed in
equipment is authorized aboard passenger carrying aircraft in packages
that do not exceed a net weight of 5 kg.
A105 The total net quantity of dangerous goods contained in one
package, excluding magnetic material, must not exceed the following:
a. 1 kg (2.2 pounds) in the case of solids;
b. 0.5 L (0.1 gallons) in the case of liquids;
c. 0.5 kg (1.1 pounds) in the case of Division 2.2 gases; or
d. any combination thereof.
(3) ``B'' codes. These provisions apply only to bulk packagings.
Except as otherwise provided in this subchapter, these special
provisions do not apply to UN portable tanks or IBCs:
Code/Special Provisions
B1 If the material has a flash point at or above 38 [deg]C (100 [deg]F)
and below 93 [deg]C (200 [deg]F), then the bulk packaging requirements
of Sec. 173.241 of this subchapter are applicable. If the material has
a flash point of less than 38 [deg]C (100 [deg]F), then the bulk
packaging requirements of Sec. 173.242 of this subchapter are
applicable.
B2 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo
tanks are not authorized.
B3 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo
tanks and DOT 57 portable tanks are not authorized.
B4 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo
tanks are not authorized.
B5 Only ammonium nitrate solutions with 35 percent or less water that
will remain completely in solution under all conditions of transport at
a maximum lading temperature of 116 [deg]C (240 [deg]F) are authorized
for transport in the following bulk packagings: MC 307, MC 312, DOT 407
and DOT 412 cargo tanks with at least 172 kPa (25 psig) design pressure.
The packaging shall be designed for a working temperature of at least
121 [deg]C (250 [deg]F). Only Specifications MC 304, MC 307 or DOT 407
cargo tank motor vehicles are authorized for transportation by vessel.
B6 Packagings shall be made of steel.
B7 Safety relief devices are not authorized on multi-unit tank car
tanks. Openings for safety relief devices on multi-unit tank car tanks
shall be plugged or blank flanged.
B8 Packagings shall be made of nickel, stainless steel, or steel with
nickel, stainless steel, lead or other suitable corrosion resistant
metallic lining.
B9 Bottom outlets are not authorized.
B10 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo
tanks, and DOT 57 portable tanks are not authorized.
B11 Tank car tanks must have a test pressure of at least 2,068.5 kPa
(300 psig). Cargo and portable tanks must have a design pressure of at
least 1,207 kPa (175 psig).
B13 A nonspecification cargo tank motor vehicle authorized in Sec.
173.247 of this subchapter must be at least equivalent in design and in
construction to a DOT 406 cargo tank or MC 306 cargo tank (if
constructed before August 31, 1995), except as follows:
[[Page 345]]
a. Packagings equivalent to MC 306 cargo tanks are excepted from the
certification, venting, and emergency flow requirements of the MC 306
specification.
b. Packagings equivalent to DOT 406 cargo tanks are excepted from
Sec. Sec. 178.345-7(d)(5), circumferential reinforcements; 178.345-10,
pressure relief; 178.345-11, outlets; 178.345-14, marking, and 178.345-
15, certification.
c. Packagings are excepted from the design stress limits at elevated
temperatures, as described in Section VIII of the ASME Code (IBR, see
Sec. 171.7 of this subchapter). However, the design stress limits may
not exceed 25 percent of the stress for 0 temper at the maximum design
temperature of the cargo tank, as specified in the Aluminum
Association's ``Aluminum Standards and Data'' (IBR, see Sec. 171.7 of
this subchapter).
B14 Each bulk packaging, except a tank car or a multi-unit-tank car
tank, must be insulated with an insulating material so that the overall
thermal conductance at 15.5 [deg]C (60 [deg]F) is no more than 1.5333
kilojoules per hour per square meter per degree Celsius (0.075 Btu per
hour per square foot per degree Fahrenheit) temperature differential.
Insulating materials must not promote corrosion to steel when wet.
B15 Packagings must be protected with non-metallic linings impervious to
the lading or have a suitable corrosion allowance.
B16 The lading must be completely covered with nitrogen, inert gas or
other inert materials.
B18 Open steel hoppers or bins are authorized.
B23 Tanks must be made of steel that is rubber lined or unlined. Unlined
tanks must be passivated before being placed in service. If unlined
tanks are washed out with water, they must be repassivated prior to
return to service. Lading in unlined tanks must be inhibited so that the
corrosive effect on steel is not greater than that of hydrofluoric acid
of 65 percent concentration.
B25 Packagings must be made from monel or nickel or monel-lined or
nickel-lined steel.
B26 Tanks must be insulated. Insulation must be at least 100 mm (3.9
inches) except that the insulation thickness may be reduced to 51 mm (2
inches) over the exterior heater coils. Interior heating coils are not
authorized. The packaging may not be loaded with a material outside of
the packaging's design temperature range. In addition, the material also
must be covered with an inert gas or the container must be filled with
water to the tank's capacity. After unloading, the residual material
also must be covered with an inert gas or the container must be filled
with water to the tank's capacity.
B27 Tanks must have a service pressure of 1,034 kPa (150 psig). Tank car
tanks must have a test pressure rating of 1,379 kPa (200 psig). Lading
must be blanketed at all times with a dry inert gas at a pressure not to
exceed 103 kPa (15 psig).
B28 Packagings must be made of stainless steel.
B30 MC 312, MC 330, MC 331 and DOT 412 cargo tanks and DOT 51 portable
tanks must be made of stainless steel, except that steel other than
stainless steel may be used in accordance with the provisions of Sec.
173.24b(b) of this subchapter. Thickness of stainless steel for tank
shell and heads for cargo tanks and portable tanks must be the greater
of 7.62 mm (0.300 inch) or the thickness required for a tank with a
design pressure at least equal to 1.5 times the vapor pressure of the
lading at 46 [deg]C (115 [deg]F). In addition, MC 312 and DOT 412 cargo
tank motor vehicles must:
a. Be ASME Code (U) stamped for 100% radiography of all pressure-
retaining welds;
b. Have accident damage protection which conforms with Sec.
178.345-8 of this subchapter;
c. Have a MAWP or design pressure of at least 87 psig: and
d. Have a bolted manway cover.
B32 MC 312, MC 330, MC 331, DOT 412 cargo tanks and DOT 51 portable
tanks must be made of stainless steel, except that steel other than
stainless steel may be used in accordance with the provisions of Sec.
173.24b(b) of this subchapter. Thickness of stainless steel for tank
shell and heads for cargo tanks and portable tanks must be the greater
of 6.35 mm (0.250 inch) or the thickness required for a tank with a
design pressure at least equal to 1.3 times the vapor pressure of the
lading at 46 [deg]C (115 [deg]F). In addition, MC 312 and DOT 412 cargo
tank motor vehicles must:
a. Be ASME Code (U) stamped for 100% radiography of all pressure-
retaining welds;
b. Have accident damage protection which conforms with Sec. 178.345-8
of this subchapter;
c. Have a MAWP or design pressure of at least 87 psig; and
d. Have a bolted manway cover.
B33 MC 300, MC 301, MC 302, MC 303, MC 305, MC 306, and DOT 406 cargo
tanks equipped with a 1 psig normal vent used to transport gasoline must
conform to Table I of this Special Provision. Based on the volatility
class determined by using ASTM D 439 and the Reid vapor pressure (RVP)
of the particular gasoline, the maximum lading pressure and maximum
ambient temperature permitted during the loading of gasoline may not
exceed that listed in Table I.
[[Page 346]]
Table I--Maximum Ambient Temperature--Gasoline
------------------------------------------------------------------------
Maximum lading and ambient
ASTM D439 volatility class temperature (see note 1)
------------------------------------------------------------------------
A...................................... 131 [deg]F
(RVP<=9.0 psia)
B...................................... 124 [deg]F
(RVP<=10.0 psia)
C...................................... 116 [deg]F
(RVP<=11.5 psia)
D...................................... 107 [deg]F
(RVP<=13.5 psia)
E...................................... 100 [deg]F
(RVP<=15.0 psia)
------------------------------------------------------------------------
Note 1: Based on maximum lading pressure of 1 psig at top of cargo tank.
B35 Tank cars containing hydrogen cyanide may be alternatively marked
``Hydrocyanic acid, liquefied'' if otherwise conforming to marking
requirements in subpart D of this part. Tank cars marked ``HYDROCYANIC
ACID'' prior to October 1, 1991 do not need to be remarked.
B37 The amount of nitric oxide charged into any tank car tank may not
exceed 1,379 kPa (200 psig) at 21 [deg]C (70 [deg]F).
B42 Tank cars must have a test pressure of 34.47 Bar (500 psig) or
greater and conform to Class 105J. Each tank car must have a reclosing
pressure relief device having a start-to-discharge pressure of 10.34 Bar
(150 psig). The tank car specification may be marked to indicate a test
pressure of 13.79 Bar (200 psig).
B44 All parts of valves and safety relief devices in contact with lading
must be of a material which will not cause formation of acetylides.
B45 Each tank must have a reclosing combination pressure relief device
equipped with stainless steel or platinum rupture discs approved by the
AAR Tank Car Committee.
B46 The detachable protective housing for the loading and unloading
valves of multi-unit tank car tanks must withstand tank test pressure
and must be approved by the Associate Administrator.
B47 Each tank may have a reclosing pressure relief device having a
start-to-discharge pressure setting of 310 kPa (45 psig).
B48 Portable tanks in sodium metal service may be visually inspected at
least once every 5 years instead of being retested hydrostatically. Date
of the visual inspection must be stenciled on the tank near the other
required markings.
B49 Tanks equipped with interior heater coils are not authorized. Single
unit tank car tanks must have a reclosing pressure relief device having
a start-to-discharge pressure set at no more than 1551 kPa (225 psig).
B50 Each valve outlet of a multi-unit tank car tank must be sealed by a
threaded solid plug or a threaded cap with inert luting or gasket
material. Valves must be of stainless steel and the caps, plugs, and
valve seats must be of a material that will not deteriorate as a result
of contact with the lading.
B52 Notwithstanding the provisions of Sec. 173.24b of this subchapter,
non-reclosing pressure relief devices are authorized on DOT 57 portable
tanks.
B53 Packagings must be made of either aluminum or steel.
B54 Open-top, sift-proof rail cars are also authorized.
B55 Water-tight, sift-proof, closed-top, metal-covered hopper cars,
equipped with a venting arrangement (including flame arrestors) approved
by the Associate Administrator are also authorized.
B56 Water-tight, sift-proof, closed-top, metal-covered hopper cars are
also authorized if the particle size of the hazardous material is not
less than 149 microns.
B57 Class 115A tank car tanks used to transport chloroprene must be
equipped with a non-reclosing pressure relief device of a diameter not
less than 305 mm (12 inches) with a maximum rupture disc pressure of 310
kPa (45 psig).
B59 Water-tight, sift-proof, closed-top, metal-covered hopper cars are
also authorized provided that the lading is covered with a nitrogen
blanket.
B60 DOT Specification 106A500X multi-unit tank car tanks that are not
equipped with a pressure relief device of any type are authorized. For
the transportation of phosgene, the outage must be sufficient to prevent
tanks from becoming liquid full at 55 [deg]C (130 [deg]F).
B61 Written procedures covering details of tank car appurtenances, dome
fittings, safety devices, and marking, loading, handling, inspection,
and testing practices must be approved by the Associate Administrator
before any single unit tank car tank is offered for transportation.
B64 Each single unit tank car tank built after December 31, 1990 must be
equipped with a tank head puncture resistance system that conforms to
Sec. 179.16 of this subchapter.
B65 Tank cars must have a test pressure of 34.47 Bar (500 psig) or
greater and conform to Class 105A. Each tank car must have a pressure
relief device having a start-to-discharge pressure of 15.51 Bar (225
psig). The tank car specification may be marked to indicate a test
pressure of 20.68 Bar (300 psig).
B66 Each tank must be equipped with gas tight valve protection caps.
Outage must be sufficient to prevent tanks from becoming liquid full at
55 [deg]C (130 [deg]F). Specification 110A500W tanks must be stainless
steel.
[[Page 347]]
B67 All valves and fittings must be protected by a securely attached
cover made of metal not subject to deterioration by the lading, and all
valve openings, except safety valve, must be fitted with screw plugs or
caps to prevent leakage in the event of valve failure.
B68 Sodium must be in a molten condition when loaded and allowed to
solidify before shipment. Outage must be at least 5 percent at 98 [deg]C
(208 [deg]F). Bulk packagings must have exterior heating coils fusion
welded to the tank shell which have been properly stress relieved. The
only tank car tanks authorized are Class DOT 105 tank cars having a test
pressure of 2,069 kPa (300 psig) or greater.
B69 Dry sodium cyanide or potassium cyanide may be shipped in sift-proof
weather-resistant metal covered hopper car, covered motor vehicles,
portable tanks or non-specification bins. Bins must be approved by the
Associate Administrator.
B70 If DOT 103ANW tank car tank is used: All cast metal in contact with
the lading must have 96.7 percent nickel content; and the lading must be
anhydrous and free from any impurities.
B71 Tank cars must have a test pressure of 20.68 Bar (300 psig) or
greater and conform to Class 105, 112, 114 or 120.
B72 Tank cars must have a test pressure of 34.47 Bar (500 psig) or
greater and conform to Class 105J, 106, or 110.
B74 Tank cars must have a test pressure of 20.68 Bar (300 psig) or
greater and conform to Class 105S, 106, 110, 112J, 114J or 120S.
B76 Tank cars must have a test pressure of 20.68 Bar (300 psig) or
greater and conform to Class 105S, 112J, 114J or 120S. Each tank car
must have a reclosing pressure relief device having a start-to-discharge
pressure of 10.34 Bar (150 psig). The tank car specification may be
marked to indicate a test pressure of 13.79 Bar (200 psig).
B77 Other packaging are authorized when approved by the Associate
Administrator.
B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater
and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. Heater
pipes must be of welded construction designed for a test pressure of 500
psig. A 25 mm (1 inch) woven lining of asbestos or other approved
material must be placed between the bolster slabbing and the bottom of
the tank. If a tank car tank is equipped with a non-reclosing pressure
relief device, the rupture disc must be perforated with a 3.2 mm (0.13
inch) diameter hole. If a tank car tank is equipped with a reclosing
pressure relief valve, the tank must also be equipped with a vacuum
relief valve.
B80 Each cargo tank must have a minimum design pressure of 276 kPa (40
psig).
B81 Venting and pressure relief devices for tank car tanks and cargo
tanks must be approved by the Associate Administrator.
B82 Cargo tanks and portable tanks are not authorized.
B83 Bottom outlets are prohibited on tank car tanks transporting
sulfuric acid in concentrations over 65.25 percent.
B84 Packagings must be protected with non-metallic linings impervious to
the lading or have a suitable corrosion allowance for sulfuric acid or
spent sulfuric acid in concentration up to 65.25 percent.
B85 Cargo tanks must be marked with the name of the lading in accordance
with the requirements of Sec. 172.302(b).
B90 Steel tanks conforming or equivalent to ASME specifications which
contain solid or semisolid residual motor fuel antiknock mixture
(including rust, scale, or other contaminants) may be shipped by rail
freight or highway. The tank must have been designed and constructed to
be capable of withstanding full vacuum. All openings must be closed with
gasketed blank flanges or vapor tight threaded closures.
B115 Rail cars, highway trailers, roll-on/roll-off bins, or other non-
specification bulk packagings are authorized. Packagings must be sift-
proof, prevent liquid water from reaching the hazardous material, and be
provided with sufficient venting to preclude dangerous accumulation of
flammable, corrosive, or toxic gaseous emissions such as methane,
hydrogen, and ammonia. The material must be loaded dry.
(4) Table 1 and Table 2--IB Codes and IP Special IBC Packing
Provisions. These provisions apply only to transportation in IBCs. When
no IBC code is assigned in the Sec. 172.101 Table for a specific proper
shipping name, or in Sec. 173.225(e) for Type F organic peroxides, an
IBC may not be used unless authorized by the Associate Administrator.
The letter ``Z'' shown in the marking code for composite IBCs must be
replaced with a capital code letter designation found in Sec.
178.702(a)(2) of this subchapter to specify the material used for the
outer packaging. Tables 1 and 2 follow:
Table 1--IB Codes (IBC Codes)
------------------------------------------------------------------------
IBC Code Authorized IBCs
------------------------------------------------------------------------
IB1............................ Authorized IBCs: Metal (31A, 31B and
31N).
[[Page 348]]
Additional Requirement: Only liquids
with a vapor pressure less than or
equal to 110 kPa at 50 [deg]C (1.1 bar
at 122 [deg]F), or 130 kPa at 55
[deg]C (1.3 bar at 131 [deg]F) are
authorized.
IB2............................ Authorized IBCs: Metal (31A, 31B and
31N); Rigid plastics (31H1 and 31H2);
Composite (31HZ1).
Additional Requirement: Only liquids
with a vapor pressure less than or
equal to 110 kPa at 50 [deg]C (1.1 bar
at 122 [deg]F), or 130 kPa at 55
[deg]C (1.3 bar at 131 [deg]F) are
authorized.
IB3............................ Authorized IBCs: Metal (31A, 31B and
31N); Rigid plastics (31H1 and 31H2);
Composite (31HZ1 and 31HA2, 31HB2,
31HN2, 31HD2 and 31HH2).
Additional Requirement: Only liquids
with a vapor pressure less than or
equal to 110 kPa at 50 [deg]C (1.1 bar
at 122 [deg]F), or 130 kPa at 55
[deg]C (1.3 bar at 131 [deg]F) are
authorized, except for UN2672 (also
see Special Provision IP8 in Table 2
for UN2672).
IB4............................ Authorized IBCs: Metal (11A, 11B, 11N,
21A, 21B, 21N, 31A, 31B and 31N).
IB5............................ Authorized IBCs: Metal (11A, 11B, 11N,
21A, 21B, 21N, 31A, 31B and 31N);
Rigid plastics (11H1, 11H2, 21H1,
21H2, 31H1 and 31H2); Composite
(11HZ1, 21HZ1 and 31HZ1).
IB6............................ Authorized IBCs: Metal (11A, 11B, 11N,
21A, 21B, 21N, 31A, 31B and 31N);
Rigid plastics (11H1, 11H2, 21H1,
21H2, 31H1 and 31H2); Composite
(11HZ1, 11HZ2, 21HZ1, 21HZ2, 31HZ1 and
31HZ2).
Additional Requirement: Composite IBCs
11HZ2 and 21HZ2 may not be used when
the hazardous materials being
transported may become liquid during
transport.
IB7............................ Authorized IBCs: Metal (11A, 11B, 11N,
21A, 21B, 21N, 31A, 31B and 31N);
Rigid plastics (11H1, 11H2, 21H1,
21H2, 31H1 and 31H2); Composite
(11HZ1, 11HZ2, 21HZ1, 21HZ2, 31HZ1 and
31HZ2); Wooden (11C, 11D and 11F).
Additional Requirement: Liners of
wooden IBCs must be sift- proof.
IB8............................ Authorized IBCs: Metal (11A, 11B, 11N,
21A, 21B, 21N, 31A, 31B and 31N);
Rigid plastics (11H1, 11H2, 21H1,
21H2, 31H1 and 31H2); Composite
(11HZ1, 11HZ2, 21HZ1, 21HZ2, 31HZ1 and
31HZ2); Fiberboard (11G); Wooden (11C,
11D and 11F); Flexible (13H1, 13H2,
13H3, 13H4, 13H5, 13L1, 13L2, 13L3,
13L4, 13M1 or 13M2).
IB9............................ IBCs are only authorized if approved by
the Associate Administrator.
------------------------------------------------------------------------
Table 2--IP Codes
------------------------------------------------------------------------
IBC Code Authorized IBCs
------------------------------------------------------------------------
IP1............................ IBCs must be packed in closed freight
containers or a closed transport
vehicle.
IP2............................ When IBCs other than metal or rigid
plastics IBCs are used, they must be
offered for transportation in a closed
freight container or a closed
transport vehicle.
IP3............................ Flexible IBCs must be sift-proof and
water-resistant or must be fitted with
a sift-proof and water-resistant
liner.
IP4............................ Flexible, fiberboard or wooden IBCs
must be sift-proof and water-resistant
or be fitted with a sift-proof and
water-resistant liner.
IP5............................ IBCs must have a device to allow
venting. The inlet to the venting
device must be located in the vapor
space of the IBC under maximum filling
conditions.
IP6............................ Non-specification bulk bins are
authorized.
IP7............................ For UN identification numbers 1327,
1363, 1364, 1365, 1386, 1841, 2211,
2217, 2793 and 3314, IBCs are not
required to meet the IBC performance
tests specified in part 178, subpart N
of this subchapter.
IP8............................ Ammonia solutions may be transported in
rigid or composite plastic IBCs (31H1,
31H2 and 31HZ1) that have successfully
passed, without leakage or permanent
deformation, the hydrostatic test
specified in Sec. 178.814 of this
subchapter at a test pressure that is
not less than 1.5 times the vapor
pressure of the contents at 55 [deg]C
(131 [deg]F).
IP13........................... Transportation by vessel in IBCs is
prohibited.
IP14........................... Air shall be eliminated from the vapor
space by nitrogen or other means.
IP20........................... Dry sodium cyanide or potassium cyanide
is also permitted in siftproof, water-
resistant, fiberboard IBCs when
transported in closed freight
containers or transport vehicles.
------------------------------------------------------------------------
(5) ``N'' codes. These provisions apply only to non-bulk packagings:
Code/Special Provisions
N3 Glass inner packagings are permitted in combination or composite
packagings only if the hazardous material is free from hydrofluoric
acid.
N4 For combination or composite packagings, glass inner packagings,
other than ampoules, are not permitted.
N5 Glass materials of construction are not authorized for any part of a
packaging which is normally in contact with the hazardous material.
N6 Battery fluid packaged with electric storage batteries, wet or dry,
must conform to the packaging provisions of Sec. 173.159 (g) or (h) of
this subchapter.
N7 The hazard class or division number of the material must be marked on
the package in accordance with Sec. 172.302 of this subchapter.
However, the hazard label corresponding to the hazard class or division
may be substituted for the marking.
N8 Nitroglycerin solution in alcohol may be transported under this entry
only when the
[[Page 349]]
solution is packed in metal cans of not more than 1 L capacity each,
overpacked in a wooden box containing not more than 5 L. Metal cans must
be completely surrounded with absorbent cushioning material. Wooden
boxes must be completely lined with a suitable material impervious to
water and nitroglycerin.
N11 This material is excepted for the specification packaging
requirements of this subchapter if the material is packaged in strong,
tight non-bulk packaging meeting the requirements of subparts A and B of
part 173 of this subchapter.
N12 Plastic packagings are not authorized.
N20 A 5M1 multi-wall paper bag is authorized if transported in a closed
transport vehicle.
N25 Steel single packagings are not authorized.
N32 Aluminum materials of construction are not authorized for single
packagings.
N33 Aluminum drums are not authorized.
N34 Aluminum construction materials are not authorized for any part of a
packaging which is normally in contact with the hazardous material.
N36 Aluminum or aluminum alloy construction materials are permitted only
for halogenated hydrocarbons that will not react with aluminum.
N37 This material may be shipped in an integrally-lined fiber drum (1G)
which meets the general packaging requirements of subpart B of part 173
of this subchapter, the requirements of part 178 of this subchapter at
the packing group assigned for the material and to any other special
provisions of column 7 of the Sec. 172.101 table.
N40 This material is not authorized in the following packagings:
a. A combination packaging consisting of a 4G fiberboard box with
inner receptacles of glass or earthenware;
b. A single packaging of a 4C2 sift-proof, natural wood box; or
c. A composite packaging 6PG2 (glass, porcelain or stoneware
receptacles within a fiberboard box).
N41 Metal construction materials are not authorized for any part of a
packaging which is normally in contact with the hazardous material.
N42 1A1 drums made of carbon steel with thickness of body and heads of
not less than 1.3 mm (0.050 inch) and with a corrosion-resistant
phenolic lining are authorized for stabilized benzyl chloride if tested
and certified to the Packing Group I performance level at a specific
gravity of not less than 1.8.
N43 Metal drums are permitted as single packagings only if constructed
of nickel or monel.
N45 Copper cartridges are authorized as inner packagings if the
hazardous material is not in dispersion.
N65 Outage must be sufficient to prevent cylinders or spheres from
becoming liquid full at 55 [deg]C (130 [deg]F). The vacant space
(outage) may be charged with a nonflammable nonliquefied compressed gas
if the pressure in the cylinder or sphere at 55 [deg]C (130 [deg]F) does
not exceed 125 percent of the marked service pressure.
N72 Packagings must be examined by the Bureau of Explosives and approved
by the Associate Administrator.
N73 Packagings consisting of outer wooden or fiberboard boxes with inner
glass, metal or other strong containers; metal or fiber drums; kegs or
barrels; or strong metal cans are authorized and need not conform to the
requirements of part 178 of this subchapter.
N74 Packages consisting of tightly closed inner containers of glass,
earthenware, metal or polyethylene, capacity not over 0.5 kg (1.1
pounds) securely cushioned and packed in outer wooden barrels or wooden
or fiberboard boxes, not over 15 kg (33 pounds) net weight, are
authorized and need not conform to the requirements of part 178 of this
subchapter.
N75 Packages consisting of tightly closed inner packagings of glass,
earthenware or metal, securely cushioned and packed in outer wooden
barrels or wooden or fiberboard boxes, capacity not over 2.5 kg (5.5
pounds) net weight, are authorized and need not conform to the
requirements of part 178 of this subchapter.
N76 For materials of not more than 25 percent active ingredient by
weight, packages consisting of inner metal packagings not greater than
250 mL (8 ounces) capacity each, packed in strong outer packagings
together with sufficient absorbent material to completely absorb the
liquid contents are authorized and need not conform to the requirements
of part 178 of this subchapter.
N77 For materials of not more than two percent active ingredients by
weight, packagings need not conform to the requirements of part 178 of
this subchapter, if liquid contents are absorbed in an inert material.
N78 Packages consisting of inner glass, earthenware, or polyethylene or
other nonfragile plastic bottles or jars not over 0.5 kg (1.1 pounds)
capacity each, or metal cans not over five pounds capacity each, packed
in outer wooden boxes, barrels or kegs, or fiberboard boxes are
authorized and need not conform to the requirements of part 178 of this
subchapter. Net weight of contents in fiberboard boxes may not exceed 29
kg (64 pounds). Net weight of contents in wooden boxes, barrels or kegs
may not exceed 45 kg (99 pounds).
N79 Packages consisting of tightly closed metal inner packagings not
over 0.5 kg (1.1 pounds) capacity each, packed in outer
[[Page 350]]
wooden or fiberboard boxes, or wooden barrels, are authorized and need
not conform to the requirements of part 178 of this subchapter. Net
weight of contents may not exceed 15 kg (33 pounds).
N80 Packages consisting of one inner metal can, not over 2.5 kg (5.5
pounds) capacity, packed in an outer wooden or fiberboard box, or a
wooden barrel, are authorized and need not conform to the requirements
of part 178 of this subchapter.
N82 See Sec. 173.306 of this subchapter for classification criteria for
flammable aerosols.
N83 This material may not be transported in quantities of more than 11.5
kg (25.4 lbs) per package.
N84 The maximum quantity per package is 500 g (1.1 lbs.).
N85 Packagings certified at the Packing Group I performance level may
not be used.
N86 UN pressure receptacles made of aluminum alloy are not authorized.
N87 The use of copper valves on UN pressure receptacles is prohibited.
N88 Any metal part of a UN pressure receptacle in contact with the
contents may not contain more than 65% copper, with a tolerance of 1%.
N89 When steel UN pressure receptacles are used, only those bearing the
``H'' mark are authorized.
(6) ``R'' codes. These provisions apply only to transportation by
rail. [Reserved]
(7) ``T'' codes. (i) These provisions apply to the transportation of
hazardous materials in UN portable tanks. Portable tank instructions
specify the requirements applicable to a portable tank when used for the
transportation of a specific hazardous material. These requirements must
be met in addition to the design and construction specifications in part
178 of this subchapter. Portable tank instructions T1 through T22
specify the applicable minimum test pressure, the minimum shell
thickness (in reference steel), bottom opening requirements and pressure
relief requirements. Liquefied compressed gases are assigned to portable
tank instruction T50. Refrigerated liquefied gases that are authorized
to be transported in portable tanks are specified in tank instruction
T75.
(ii) The following table specifies the portable tank requirements
applicable to ``T'' Codes T1 through T22. Column 1 specifies the ``T''
Code. Column 2 specifies the minimum test pressure, in bar (1 bar = 14.5
psig), at which the periodic hydrostatic testing required by Sec.
180.605 of this subchapter must be conducted. Column 3 specifies the
section reference for minimum shell thickness or, alternatively, the
minimum shell thickness value. Column 4 specifies the applicability of
Sec. 178.275(g)(3) of this subchapter for the pressure relief devices.
When the word ``Normal'' is indicated, Sec. 178.275(g)(3) of this
subchapter does not apply. Column 5 references the applicable
requirements for bottom openings in part 178 of this subchapter or
references ``Prohibited'' which means bottom openings are prohibited.
The table follows:
Table of Portable Tank T Codes T1-T22
[Portable tank codes T1-T22 apply to liquid and solid hazardous materials of Classes 3 through 9 which are
transported in portable tanks.]
----------------------------------------------------------------------------------------------------------------
Pressure-relief
Portable tank Minimum test Minimum shell thickness (in requirements (See Bottom opening
instruction (1) pressure mm-reference steel) (See Sec. 178.275(g)) requirements (See Sec.
(bar) (2) Sec. 178.274(d)) (3) (4) 178.275(d)) (5)
----------------------------------------------------------------------------------------------------------------
T1............... 1.5 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(2)
T2............... 1.5 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(3)
T3............... 2.65 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(2)
T4............... 2.65 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(3)
T5............... 2.65 Sec. 178.274(d)(2) Sec. Prohibited
178.275(g)(3).
T6............... 4 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(2)
T7............... 4 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(3)
T8............... 4 Sec. 178.274(d)(2) Normal............. Prohibited
T9............... 4 6 mm Normal............. Prohibited
T10.............. 4 6 mm Sec. Prohibited
178.275(g)(3).
T11.............. 6 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(3)
T12.............. 6 Sec. 178.274(d)(2) Sec. Sec. 178.275(d)(3)
178.275(g)(3).
T13.............. 6 6 mm Normal............. Prohibited
T14.............. 6 6 mm Sec. Prohibited
178.275(g)(3).
T15.............. 10 Sec. 178.274(d)(2) Normal............. Sec. 178.275(d)(3)
T16.............. 10 Sec. 178.274(d)(2) Sec. Sec. 178.275(d)(3)
178.275(g)(3).
T17.............. 10 6 mm Normal............. Sec. 178.275(d)(3)
T18.............. 10 6 mm Sec. Sec. 178.275(d)(3)
178.275(g)(3).
[[Page 351]]
T19.............. 10 6 mm Sec. Prohibited
178.275(g)(3).
T20.............. 10 8 mm Sec. Prohibited
178.275(g)(3).
T21.............. 10 10 mm Normal............. Prohibited
T22.............. 10 10 mm Sec. Prohibited
178.275(g)(3).
----------------------------------------------------------------------------------------------------------------
(iii) T50. When portable tank instruction T50 is referenced in
Column (7) of the Sec. 172.101 Table, the applicable liquefied
compressed gases are authorized to be transported in portable tanks in
accordance with the requirements of Sec. 173.313 of this subchapter.
(iv) T75. When portable tank instruction T75 is referenced in Column
(7) of the Sec. 172.101 Table, the applicable refrigerated liquefied
gases are authorized to be transported in portable tanks in accordance
with the requirements of Sec. 178.277 of this subchapter.
(v) UN and IM portable tank codes/special provisions. When a
specific portable tank instruction is specified by a ``T'' Code in
Column (7) of the Sec. 172.101 Table for a specific hazardous material,
a specification portable tank conforming to an alternative tank
instruction may be used if:
(A) The alternative portable tank has a higher or equivalent test
pressure (for example, 4 bar when 2.65 bar is specified);
(B) The alternative portable tank has greater or equivalent wall
thickness (for example, 10 mm when 6 mm is specified);
(C) The alternative portable tank has a pressure relief device as
specified in the ``T'' Code. If a frangible disc is required in series
with the reclosing pressure relief device for the specified portable
tank, the alternative portable tank must be fitted with a frangible disc
in series with the reclosing pressure relief device; and
(D) With regard to bottom openings--
(1) When two effective means are specified, the alternative portable
tank is fitted with bottom openings having two or three effective means
of closure or no bottom openings; or
(2) When three effective means are specified, the portable tank has
no bottom openings or three effective means of closure; or
(3) When no bottom openings are authorized, the alternative portable
tank must not have bottom openings.
(vi) Except when an organic peroxide is authorized under Sec.
173.225(g), if a hazardous material is not assigned a portable tank
``T'' Code, the hazardous material may not be transported in a portable
tank unless approved by the Associate Administrator.
(8) ``TP'' codes. (i) These provisions apply to the transportation
of hazardous materials in IM and UN Specification portable tanks.
Portable tank special provisions are assigned to certain hazardous
materials to specify requirements that are in addition to those provided
by the portable tank instructions or the requirements in part 178 of
this subchapter. Portable tank special provisions are designated with
the abbreviation TP (tank provision) and are assigned to specific
hazardous materials in Column (7) of the Sec. 172.101 Table.
(ii) The following is a list of the portable tank special
provisions:
Code/Special Provisions
TP1 The maximum degree of filling must not exceed the degree of
filling determined by the following:
[GRAPHIC] [TIFF OMITTED] TN21JN01.000
Where:
tr is the maximum mean bulk temperature during transport, and
tf is the temperature in degrees celsius of the liquid during
filling.
TP2 a. The maximum degree of filling must not exceed the degree of
filling determined by the following:
[[Page 352]]
[GRAPHIC] [TIFF OMITTED] TN21JN01.001
Where:
tr is the maximum mean bulk temperature during transport,
tf is the temperature in degrees celsius of the liquid during
filling, and
[alpha] is the mean coefficient of cubical expansion of the liquid
between the mean temperature of the liquid during filling
(tf) and the maximum mean bulk temperature during
transportation (tr) both in degrees celsius.
b. For liquids transported under ambient conditions [alpha] may be
calculated using the formula:
[GRAPHIC] [TIFF OMITTED] TN21JN01.009
Where:
d15 and d50 are the densities (in units of mass
per unit volume) of the liquid at 15 [deg]C (59 [deg]F) and 50 [deg]C
(122 [deg]F), respectively.
TP3 The maximum degree of filling (in %) for solids transported
above their melting points and for elevated temperature liquids shall be
determined by the following:
[GRAPHIC] [TIFF OMITTED] TR14JN05.003
Where: df and dr are the mean densities of the
liquid at the mean temperature of the liquid during filling and the
maximum mean bulk temperature during transport respectively.
TP4 The maximum degree of filling for portable tanks must not exceed
90%.
TP5 For a portable tank used for the transport of flammable
refrigerated liquefied gases or refrigerated liquefied oxygen, the
maximum rate at which the portable tank may be filled must not exceed
the liquid flow capacity of the primary pressure relief system rated at
a pressure not exceeding 120 percent of the portable tank's design
pressure. For portable tanks used for the transport of refrigerated
liquefied helium and refrigerated liquefied atmospheric gas (except
oxygen), the maximum rate at which the tank is filled must not exceed
the liquid flow capacity of the pressure relief device rated at 130
percent of the portable tank's design pressure. Except for a portable
tank containing refrigerated liquefied helium, a portable tank shall
have an outage of at least two percent below the inlet of the pressure
relief device or pressure control valve, under conditions of incipient
opening, with the portable tank in a level attitude. No outage is
required for helium.
TP6 The tank must be equipped with a pressure release device which
prevent a tank from bursting under fire engulfment conditions (the
conditions prescribed in CGA pamphlet S-1.2 (see Sec. 171.7 of this
subchapter) or alternative conditions approved by the Associate
Administrator may be used to consider the fire engulfment condition),
taking into account the properties of the hazardous material to be
transported.
TP7 The vapor space must be purged of air by nitrogen or other
means.
TP8 A portable tank having a minimum test pressure of 1.5 bar (150
kPa) may be used when the flash point of the hazardous material
transported is greater than 0 [deg]C (32 [deg]F).
TP9 A hazardous material assigned to special provision TP9 in Column
(7) of the Sec. 172.101 Table may only be transported in a portable
tank if approved by the Associate Administrator.
TP10 The portable tank must be fitted with a lead lining at least 5
mm (0.2 inches) thick. The lead lining must be tested annually to ensure
that it is intact and functional. Another suitable lining material may
be used if approved by the Associate Administrator.
TP12 This material is considered highly corrosive to steel.
TP13 Self-contained breathing apparatus must be provided when this
hazardous material is transported by sea.
TP16 The portable tank must be protected against over and under
pressurization which may be experienced during transportation. The means
of protection must be approved by the approval agency designated to
approve the portable tank in accordance with the procedures in part 107,
subpart E, of this subchapter. The pressure relief device must be
preceded by a frangible disk in accordance with the requirements in
Sec. 178.275(g)(3) of this subchapter to prevent crystallization of the
product in the pressure relief device.
TP17 Only inorganic non-combustible materials may be used for
thermal insulation of the tank.
TP18 The temperature of this material must be maintained between 18
[deg]C (64.4 [deg]F) and 40 [deg]C (104 [deg]F) while in transportation.
Portable tanks containing solidified methacrylic acid must not be
reheated during transportation.
TP19 The calculated wall thickness must be increased by 3 mm at the
time of construction. Wall thickness must be verified ultrasonically at
intervals midway between periodic hydraulic tests (every 2.5 years). The
portable tank must not be used if the wall thickness is less than that
prescribed by the applicable T code in Column (7) of the Table for this
material.
TP20 This hazardous material must only be transported in insulated
tanks under a nitrogen blanket.
[[Page 353]]
TP21 The wall thickness must not be less than 8 mm. Portable tanks
must be hydraulically tested and internally inspected at intervals not
exceeding 2.5 years.
TP22 Lubricants for portable tank fittings (for example, gaskets,
shut-off valves, flanges) must be oxygen compatible.
TP24 The portable tank may be fitted with a device to prevent the
build up of excess pressure due to the slow decomposition of the
hazardous material being transported. The device must be in the vapor
space when the tank is filled under maximum filling conditions. This
device must also prevent an unacceptable amount of leakage of liquid in
the case of overturning.
TP25 Sulphur trioxide 99.95% pure and above may be transported in
tanks without an inhibitor provided that it is maintained at a
temperature equal to or above 32.5 [deg]C (90.5 [deg]F).
TP26 The heating device must be exterior to the shell. For UN 3176,
this requirement only applies when the hazardous material reacts
dangerously with water.
TP27 A portable tank having a minimum test pressure of 4 bar (400
kPa) may be used provided the calculated test pressure is 4 bar or less
based on the MAWP of the hazardous material, as defined in Sec. 178.275
of this subchapter, where the test pressure is 1.5 times the MAWP.
TP28 A portable tank having a minimum test pressure of 2.65 bar (265
kPa) may be used provided the calculated test pressure is 2.65 bar or
less based on the MAWP of the hazardous material, as defined in Sec.
178.275 of this subchapter, where the test pressure is 1.5 times the
MAWP.
TP29 A portable tank having a minimum test pressure of 1.5 bar
(150.0 kPa) may be used provided the calculated test pressure is 1.5 bar
or less based on the MAWP of the hazardous materials, as defined in
Sec. 178.275 of this subchapter, where the test pressure is 1.5 times
the MAWP.
TP30 This hazardous material may only be transported in insulated
tanks.
TP31 This hazardous material may only be transported in tanks in the
solid state.
TP32 Portable tanks may be used subject to the following conditions:
a. Each portable tank constructed of metal must be fitted with a
pressure-relief device consisting of a reclosing spring loaded type, a
frangible disc or a fusible element. The set to discharge for the spring
loaded pressure relief device and the burst pressure for the frangible
disc, as applicable, must not be greater than 2.65 bar for portable
tanks with minimum test pressures greater than 4 bar;
b. The suitability for transport in tanks must be demonstrated using
test 8(d) in Test Series 8 (see UN Manual of Tests and Criteria, Part 1,
Sub-section 18.7) (IBR, see Sec. 171.7 of this subchapter) or an
alternative means approved by the Associate Administrator.
TP33 The portable tank instruction assigned for this substance
applies for granular and powdered solids and for solids which are filled
and discharged at temperatures above their melting point which are
cooled and transported as a solid mass. Solid substances transported or
offered for transport above their melting point are authorized for
transportation in portable tanks conforming to the provisions of
portable tank instruction T4 for solid substances of packing group III
or T7 for solid substances of packing group II, unless a tank with more
stringent requirements for minimum shell thickness, maximum allowable
working pressure, pressure-relief devices or bottom outlets are assigned
in which case the more stringent tank instruction and special provisions
shall apply. Filling limits must be in accordance with portable tank
special provision TP3. Solids meeting the definition of an elevated
temperature material must be transported in accordance with the
applicable requirements of this subchapter.
TP37 IM portable tanks are only authorized for the shipment of
hydrogen peroxide solutions in water containing 72% or less hydrogen
peroxide by weight. Pressure relief devices shall be designed to prevent
the entry of foreign matter, the leakage of liquid and the development
of any dangerous excess pressure. In addition, the portable tank must be
designed so that internal surfaces may be effectively cleaned and
passivated. Each tank must be equipped with pressure relief devices
conforming to the following requirements:
------------------------------------------------------------------------
Total
Concentration of hydrogen per peroxide solution \1\
------------------------------------------------------------------------
52% or less................................................... 11
Over 52%, but not greater than 60%............................ 22
Over 60%, but not greater than 72%............................ 32
------------------------------------------------------------------------
\1\ Total venting capacity in standard cubic feet hour (S.C.F.H.) per
pound of hydrogen peroxide solution.
TP38 Each portable tank must be insulated with an insulating
material so that the overall thermal conductance at 15.5 [deg]C (60
[deg]F) is no more than 1.5333 kilojoules per hour per square meter per
degree Celsius (0.075 Btu per hour per square foot per degree
Fahrenheit) temperature differential. Insulating materials may not
promote corrosion to steel when wet.
TP44 Each portable tank must be made of stainless steel, except that
steel other than stainless steel may be used in accordance with the
provisions of Sec. 173.24b(b) of this subchapter. Thickness of
stainless steel for tank shell and heads must be the greater of 7.62 mm
(0.300 inch) or the thickness required for a portable tank with a design
pressure at least equal to 1.5 times the vapor pressure of the hazardous
material at 46 [deg]C (115 [deg]F).
[[Page 354]]
TP45 Each portable tank must be made of stainless steel, except that
steel other than stainless steel may be used in accordance with the
provisions of 173.24b(b) of this subchapter. Thickness of stainless
steel for portable tank shells and heads must be the greater of 6.35 mm
(0.250 inch) or the thickness required for a portable tank with a design
pressure at least equal to 1.3 times the vapor pressure of the hazardous
material at 46 [deg]C (115 [deg]F).
TP46 Portable tanks in sodium metal service are not required to be
hydrostatically retested.
(9) ``W'' codes. These provisions apply only to transportation by
water:
Code/Special Provisions
W7 Vessel stowage category for uranyl nitrate hexahydrate solution is
``D'' as defined in Sec. 172.101(k)(4).
W8 Vessel stowage category for pyrophoric thorium metal or pyrophoric
uranium metal is ``D'' as defined in Sec. 172.101(k)(4).
W9 When offered for transportation by water, the following Specification
packagings are not authorized unless approved by the Associate
Administrator: woven plastic bags, plastic film bags, textile bags,
paper bags, IBCs and bulk packagings.
W41 When offered for transportation by water, this material must be
packaged in bales and be securely and tightly bound with rope, wire or
similar means.
[Amdt. 172-123, 55 FR 52582, Dec. 21, 1990]
Editorial Note: For Federal Register citations affecting Sec.
172.102, see the List of CFR Sections Affected which appears in the
Finding Aids section of the printed volume and on GPO Access.
Effective Date Notes: 1. At 72 FR 4455, Jan. 31, 2007, Sec. 172.102
was amended by amending (c)(1) and (2) by removing Special Provisions
``60'' and Special Provisions ``A51'' and ``A52'', effective Oct. 1,
2007.
2. At 72 FR 55092, Sept 28, 2007, effectiveness of the amendment at
72 FR 4455, Jan. 31, 2007 was delayed until Oct. 1, 2008.