1.1 Background
1.1.1 History of Procedure
The OSHA Analytical Laboratory recently received a
set of field samples that required analysis for dicyclopentadiene. The air samples had been
collected with isopropyl alcohol impingers. Due to the inconvenience of sampling with an
impinger, we set out to find a solid sorbent tube to collect the
dicyclopentadiene. Similar pentadiene compounds have been collected on solid sorbent tubes, desorbed with a suitable solvent and analyzed by gas
chromatography using a flame ionization detector. This procedure was tried for dicyclopentadiene using SKC Lot 120 charcoal tube and desorbing with carbon disulfide and was quite adequate.
1.1.2 Toxic effects.
(This section is for information only and should not be taken as the basis of OSHA policy).
Dicyclopentadiene is classified as moderately toxic. The LD 50 for dicyclopentadiene given orally.to rats is 353 mg/kg (Ref.
5.1).
1.1.3 Potential workplace exposure.
No workplace exposure level could be found in the literature but dicyclopentadiene is used as an intermediate for cyclodiene
pesticides. It is also used as a fire retardant and as a curing agent for elastomers (Ref.
5.2).
1.1.4 Physical properties (Ref. 5.2)
Synonyms: |
Bicyclopentadiene; 1,3-cyclopentadiene, dimer; DCPD |
Molecular weight: |
132.21 |
Boiling point: |
64-65°C at 14 mmHg |
Melting point: |
32°C |
Density: |
0.9302 at 35°C/4°C |
Flash point: |
90°F (OC) |
Solubility: |
Soluble in alcohol, acetic acid, carbon tetrachloride,
and petroleum ether. Very soluble in ether. Insoluble in water at
20°C |
Description: |
Colorless liquid, terpene-like odor |
Molecular formula: |
C10H12 |
Structure: |
|
1.2 Limit defining parameters
1.2.1 Detection limit
Detection limit of the analytical procedure is 2.1 ng/injection. This is the amount of analyte which will give a peak whose height is approximately five times the baseline noise.
1.2.2 Sensitivity
The sensitivity of the analytical procedure over a concentration range of 0.025 to 0.25
µg/mL is 532480 area units per µg/mL of dicyclopentadiene. The sensitivity is determined by the slope of the
calibration curve (See Figure 3.5.3).
1.3 Advantages
1.3.1 The sampling procedure is convenient.
1.3.2 The analytical method is reproducible and sensitive.
1.3.3 Reanalysis of samples is possible.
1.3.4 It may be possible to analyze other compounds at
the same time.
1.3.5 Interferences may be avoided by proper selection of column and GC parameters.
1.4 Disadvantages
None known.
2. 1 Apparatus
2.1.1 A calibrated personal sampling pump whose flow can
be determined within ±5% of the recommended flow.
2.1.2 SKC Lot 120 charcoal tubes were used: glass tube with both ends flame sealed, 7 cm long with a 6-mm
O.D. and a 4 mm I.D., containing 2 sections of coconut shell charcoal separated by a 2-mm portion of urethane foam. The adsorbing section contains 100 mg
of charcoal, the backup section 50 mg. A 3-mm portion of urethane foam is placed between the
outlet end of the tube and the backup section. A plug of silanized glass wool is placed in front of the adsorbing section.
2.2 Reagents
None required.
2.3 Sampling technique
2.3.1 The ends of the charcoal tubes are opened immediately before sampling.
2.3.2 Connect the charcoal tube to the sampling pump with flexible tubing.
2.3.3 Tubes should be placed in a vertical position to minimize channeling, with the backup section of charcoal towards the pump.
2.3.4 Air being sampled should not pass through any hose or tubing before entering the charcoal tubes.
2.3.5 Seal the charcoal tubes with plastic caps
immediately after sampling. Seal each sample with official OSHA label lengthwise.
2.3.6 With each batch of samples, submit at least one blank tube from the same lot used for samples. This tube should be subjected to exactly the same
handling as the samples (break ends, seal, transport) except that no air is drawn through it.
2.3.7 Transport the samples (and corresponding paperwork) to the laboratory for analysis.
2.3.8 If bulk samples are submitted for analysis, they should be transported in glass containers with
Teflon-lined caps. These samples must not be put in the same container used for the charcoal tubes.
2.4 Desorption efficiency
Six charcoal tubes were spiked with dicyclopentadiene at ½, 1 and 2 times the target concentration and refrigerated over- night. The charcoal was desorbed with 1 mL carbon disulfide with
1 µL/mL ethyl benzene internal standard and analyzed by gas chromatography with a flame ionization detector.
½× Target Concentration (116.3 µg)
Sample |
% Recovery |
Average % Recovery |
1 |
87.1 |
|
2 |
93.0 |
|
3 |
92.7 |
|
4 |
90.9 |
|
5 |
89.9 |
|
6 |
93.6 |
91.7 |
1× Target Concentration (232.6 µg)
Sample |
% Recovery |
Average % Recovery |
1 |
98.3 |
|
2 |
94.6 |
|
3 |
98.1 |
|
4 |
97.5 |
|
5 |
94.7 |
|
6 |
96.6 |
96.6 |
2× Target Concentration (465.2 µg)
Sample |
% Recovery |
Average % Recovery |
1 |
91.4 |
|
2 |
92.3 |
|
3 |
94.9 |
|
4 |
90.8 |
|
5 |
91.5 |
|
6 |
90.4 |
91.9 |
2.5 Retention efficiency
Six charcoal tubes were spiked with 465.2 µg of dicyclopentadiene. Ten liters of humid air (about 85% relative humidity) were drawn through each tube at 0.1
L/mmin. The tubes were desorbed with 1 mL of carbon disulfide with 1 µL/mL ethyl benzene internal standard and analyzed by gas chromatography with a flame ionization detector.
Sample |
Treatment |
% Recovery |
Average % Recovery |
1 |
10 L Humid Air |
94.0 |
|
2 |
" |
94.0 |
|
3 |
" |
95.7 |
|
4 |
" |
93.4 |
|
5 |
" |
94.1 |
|
6 |
" |
93.7 |
94.2 |
2.6 Sample storage
Twelve charcoal tubes were spiked with 232.6 µg of dicyclopentadiene. Six tubes were stored in a refrigerator for ten days and the other six tubes were stored at ambient
temperature for ten days.
Sample |
Storage Days |
Treatment |
% Recovery |
Average % Recovery |
1 |
10 |
Refrigerated |
94.5 |
|
2 |
10 |
" |
94.6 |
|
3 |
10 |
" |
94.0 |
|
4 |
10 |
" |
94.6 |
|
5 |
10 |
" |
95.0 |
|
6 |
10 |
" |
94.2 |
94.5 |
|
|
|
|
|
7 |
10 |
Ambient |
92.5 |
|
8 |
10 |
" |
92.6 |
|
9 |
10 |
" |
93.2 |
|
10 |
10 |
" |
92.9 |
|
11 |
10 |
" |
93.4 |
|
12 |
10 |
" |
94.1 |
93.1 |
2.7 Air volume and sampling rate studied.
2.7.1 The air volume is 10.0 liters.
2.7.2 The sampling rate is 0.1 liters per minute.
2.8 Interferences
It is important to be aware of other components in the atmosphere which may interfere with the collection of the analyte.
2.9 Safety precautions
2.9.1. Care must be taken when opening the sealed ends of
the charcoal tubes to avoid serious cuts to the hands.
2.9.2 Safety glasses should be worn when opening the sealed ends of the charcoal tubes to avoid
injury to the eyes from glass splinters.
2.9.3 Attach the sampling equipment to the worker in such a manner that it will not interfere with the work performance or safety of the employee.
2.9.4 Follow all safety practices that apply to the work area being sampled.
3.1 Apparatus
3.1.1 Gas chromatograph equipped with a flame ionization
detector.
3.1.2 GC column capable of separating the analyte and an internal standard from any interferences. The column used was a 12 ft
× 1/8 in. stainless steel column packed with 10% FFAP on 80/100 Chromosorb
WAW.
3.1.3 An electronic integrator or some other suitable method of measuring peak areas.
3.1.4 Two milliliter vials with Teflon-lined caps.
3.1.5 A 1-µL syringe or other convenient size for sample injection.
3.1.6 Pipets for dispensing the desorbing solution. The Glenco
1 mL dispenser was used in this method.
3.1.7 Volumetric flasks, 5 mL and other convenient sizes for preparing standards.
3.1.8 Pipets of a convenient size for standard preparation.
3.2 Reagents
3.2.1 Carbon disulfide, chromatographic grade.
3.2.2 Dicyclopentadiene, reagent grade.
3.2.3 An internal standard, such as ethyl benzene,
reagent grade.
3.2.4 Purified GC grade nitrogen or helium, hydrogen, and air.
3.2.5 Desorbing reagent - 1 µL internal standard/ 1 mL carbon disulfide.
3.3 Standard preparation
3.3.1 Standards are prepared by diluting a known quantity of the analyte in the desorbing solution.
3.3.2 A concentration of 0.25 µL/mL of the analyte in the desorbing solution is equivalent to 4.45 ppm for a 10.0 liter air volume, using the desorption
efficiency of 96.6%.
3.3.3 At least two separate standards should be made.
3.4 Sample preparation
3.4.1 Sample tubes are opened and the front and back
sections of each tube are placed in a separate 2 mL vial.
3.4.2 Each section is desorbed with 1 mL of the desorbing reagent.
3.4.3 The vials are sealed immediately and allowed to desorb for 30 minutes with occasional shaking.
3.5 Analysis
3.5.1 GC conditions
Flow Rates (mL/min) |
Temperature (0°C) |
Nitrogen: |
20 |
Injector: |
200 |
Hydrogen: |
22 |
Detector: |
250 |
Air: |
240 |
Column: |
120 |
|
|
|
Injection: |
0.9 µL |
|
Elution time: |
5.7 minutes |
|
Chromatogram: |
|
Figure 3.5.1. Chromatogram of Dicyclopentadiene at the Target Concentration and Detection Limit.
3.5.2 Peak areas are measured by an integrator or other suitable means.
3.5.3 An internal standard procedure is used. The integrator is calibrated to report ppm based on the concentration of the analytical standard, a 10.0 liter air volume, and the desorption efficiency. A plot of dicyclopentadiene at different
concentrations shows it to be very linear.
3.6 Interferences (analytical)
3.6.1 Any compound having the general retention time of the analyte or the internal standard used is an interference. Possible interferences should be listed on the sample data sheet. GC parameters should be adjusted if necessary so these
interferences will pose no problems.
3.6.2 Retention time data on a single column is not considered proof of chemical identity. Samples over the PEL should be confirmed by GC/Mass Spec or other
suitable means.
3.7 Calculations
3.7.1 To calculate the ppm of analyte in standards based on 10 liter air sample, and 1 mL desorbing solution.
µL/mL |
= |
Standard concentration |
24.4 |
= |
Molar volume (mL/mmole) at 25°C and 760 mmHg |
MW |
= |
Molecular weight = 132.21 mg/mmole |
p |
= |
Density = 0.9302 µg/µL |
1 mL |
= |
Desorption volume |
10 L |
= |
10 liter air sample |
3.7.2 Since the integrator was calibrated to report
results in ppm based on 10 L air sample, the following calculation is used:
|
where A = ppm on report |
|
where C = ppm on report for blank |
|
where B = air volume of sample (liters) |
3.7.3 This calculation is done for each section of the sampling tube and the results added together.
3.8 Safety precautions
3.8.1 All handling of solvents should be done in a hood.
3.8.2 Avoid skin contact with all solvents.
3.8.3 Wear safety glasses at all times.
5.1 Cysewski, S.J. et al,
"Archive of Environmental Contamination Toxicology", 10(5); 605-15, (1981).
5.2 "Toxicology Data Bank", (online computerized data base), National Library of Medicine.