[Code of Federal Regulations]
[Title 40, Volume 5]
[Revised as of July 1, 2004]
From the U.S. Government Printing Office via GPO Access
[CITE: 40CFR59.412]

[Page 337]
 
                   TITLE 40--PROTECTION OF ENVIRONMENT
 
         CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)
 
PART 59_NATIONAL VOLATILE ORGANIC COMPOUND EMISSION STANDARDS FOR CONSUMER 
AND COMMERCIAL PRODUCTS--Table of Contents
 
  Subpart D_National Volatile Organic Compound Emission Standards for 
                         Architectural Coatings
 
Sec. 59.412  Incorporations by reference.

    (a) The materials listed in this section are incorporated by 
reference in the paragraphs noted in Sec. 59.401. These incorporations 
by reference were approved by the Director of the Federal Register in 
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. These materials are 
incorporated as they exist on the date of the approval, and notice of 
any changes in these materials will be published in the Federal 
Register. The materials are available for purchase at the corresponding 
addresses noted below, and all are available for inspection at the Air 
and Radiation Docket and Information Center, U.S. EPA, 401 M St., SW., 
Washington, DC 20460; at the EPA Library (MD-35), U.S. EPA, Research 
Triangle Park, North Carolina; or at the National Archives and Records 
Administration (NARA). For information on the availability of this 
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/
federal--register/code--of--federal--regulations/ibr--locations.html.
    (b) The materials listed below are available for purchase at the 
following address: American Society for Testing and Materials (ASTM), 
100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.
    (1) ASTM Method C 1315-95, Standard Specification for Liquid 
Membrane-Forming Compounds Having Special Properties for Curing and 
Sealing Concrete, incorporation by reference approved for Sec. 59.401, 
Concrete curing and sealing compound.
    (2) ASTM Method D 523-89, Standard Test Method for Specular Gloss, 
incorporation by reference approved for Sec. 59.401, Flat coating and 
Nonflat coating.
    (3) ASTM Method D 1640-83 (Reapproved 1989), Standard Test Methods 
for Drying, Curing, or Film Formation of Organic Coatings at Room 
Temperature, incorporation by reference approved for Sec. 59.401, 
Quick-dry enamel and Quick-dry primer, sealer, and undercoater.
    (4) ASTM Method D 3912-80 (Reapproved 1989), Standard Test Method 
for Chemical Resistance of Coatings Used in Light-Water Nuclear Power 
Plants, incorporation by reference approved for Sec. 59.401, Nuclear 
coating.
    (5) ASTM Method D 4082-89, Standard Test Method for Effects of Gamma 
Radiation on Coatings for Use in Light-Water Nuclear Power Plants, 
incorporation by reference approved for Sec. 59.401, Nuclear coating.
    (c) The following material is available from the AAMA, 1827 Walden 
Office Square, Suite 104, Schaumburg, IL 60173.
    (1) AAMA 605-98, Voluntary Specification Requirements and Test 
Procedures for High Performance Organic Coatings on Aluminum Extrusions 
and Panels, incorporation by reference approved for Sec. 59.401, 
Extreme high durability coating.
    (2) [Reserved]

[63 FR 48877, Sept. 11, 1998, as amended at 69 FR 18803, Apr. 9, 2004]