[Federal Register: November 8, 2002 (Volume 67, Number 217)]
[Proposed Rules]
[Page 68047-68051]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr08no02-18]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
[[Page 68047]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2001-CE-37-AD]
RIN 2120-AA64
Airworthiness Directives; Quality Aerospace, Inc., S2R Series and
Model 600 S2D Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes to supersede Airworthiness Directive
(AD) 2000-11-16, which currently applies to certain Quality Aerospace,
Inc. (Quality Aerospace) (formerly Ayres Corporation) S2R series and
Model 600 S2D airplanes. AD 2000-11-16 requires you to repetitively
inspect the \1/4\-inch and \5/16\-inch bolt hole areas on the lower
spar caps for fatigue cracking; replace or repair any lower spar cap
where fatigue cracking is found; and report any fatigue cracking found.
AD 2000-11-16 resulted from an accident of an Ayres S2R series airplane
where the wing separated from the airplane in flight. Since AD 2000-11-
16, additional airplanes have been identified that were manufactured
with a similar design to those affected by the AD and a third repair
option has been developed. This proposed AD would retain the repetitive
inspections and replacement (if necessary) requirements of the lower
spar caps that are currently required in AD 2000-11-16, add additional
airplanes to the Applicability of the AD, and add a third repair
option. The actions specified by this proposed AD are intended to
detect and correct fatigue cracking of the lower spar caps, which could
result in the wing separating from the airplane with consequent loss of
control of the airplane.
DATES: The Federal Aviation Administration (FAA) must receive any
comments on this proposed rule on or before January 15, 2003.
ADDRESSES: Submit comments to FAA, Central Region, Office of the
Regional Counsel, Attention: Rules Docket No. 2001-CE-37-AD, 901
Locust, Room 506, Kansas City, Missouri 64106. You may view any
comments at this location between 8 a.m. and 4 p.m., Monday through
Friday, except Federal holidays. You may also send comments
electronically to the following address: 9-ACE-7-Docket@faa.gov.
Comments sent electronically must contain ``Docket No. 2001-CE-37-AD''
in the subject line. If you send comments electronically as attached
electronic files, the files must be formatted in Microsoft Word 97 for
Windows or ASCII text.
You may get service information that applies to this proposed AD
from Quality Aerospace, Inc., P.O. Box 3050, Albany, Georgia 31706-
3050; telephone: (229) 883-1440; facsimile: (229) 883-9790. You may
also view this information at the Rules Docket at the address above.
FOR FURTHER INFORMATION CONTACT: Cindy Lorenzen, Aerospace Engineer,
FAA, Aircraft Certification Office, One Crown Center, 1895 Phoenix
Boulevard, suite 450, Atlanta, Georgia 30349; telephone: (770) 703-
6078; facsimile: (770) 703-6097.
SUPPLEMENTARY INFORMATION:
Comments Invited
How Do I Comment on This Proposed AD?
The FAA invites comments on this proposed rule. You may submit
whatever written data, views, or arguments you choose. You need to
include the rule's docket number and submit your comments to the
address specified under the caption ADDRESSES. We will consider all
comments received on or before the closing date. We may amend this
proposed rule in light of comments received. Factual information that
supports your ideas and suggestions is extremely helpful in evaluating
the effectiveness of this proposed AD action and determining whether we
need to take additional rulemaking action.
Are There Any Specific Portions of This Proposed AD I Should Pay
Attention To?
The FAA specifically invites comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed rule that
might suggest a need to modify the rule. You may view all comments we
receive before and after the closing date of the rule in the Rules
Docket. We will file a report in the Rules Docket that summarizes each
contact we have with the public that concerns the substantive parts of
this proposed AD.
How Can I Be Sure FAA Receives My Comment?
If you want FAA to acknowledge the receipt of your mailed comments,
you must include a self-addressed, stamped postcard. On the postcard,
write ``Comments to Docket No. 2001-CE-37-AD.'' We will date stamp and
mail the postcard back to you.
Discussion
Has FAA Taken Any Action to This Point?
An accident on an Ayres S2R series airplane where the wing
separated from the airplane in flight caused us to issue AD 2000-11-16,
Amendment 39-11764 (65 FR 36055, June 7, 2000). This AD requires the
following on certain Quality Aerospace S2R series and Model 600 S2D
airplanes:
--Repetitively inspect the \1/4\-inch and \5/16\-inch bolt hole areas
on the lower spar caps for fatigue cracking;
--Replacing or repairing any lower spar cap where fatigue cracking is
found; and
--Reporting any fatigue cracking to FAA.
AD 2000-11-16 superseded AD 97-17-03, Amendment 39-10195 (62 FR
43296, August 18, 1997), which required accomplishing the following:
--Inspecting the \1/4\-inch and \5/16\-inch bolt hole areas on the
lower spar caps for fatigue cracking;
--Replacing any lower spar cap where fatigue cracking is found; and
--Reporting any fatigue cracking to FAA.
AD 2000-11-16 made the inspections required in AD 97-17-03
repetitive, added additional airplanes to the Applicability of the AD,
changed the initial compliance time for all airplanes, and arranged the
affected airplanes into six groups based on usage and configuration.
AD 97-17-03 superseded AD 97-13-11, Amendment 39-10071 (62 FR
[[Page 68048]]
36978, July 10, 1997), which required accomplishing the following:
--Inspecting the \1/4\-inch and \5/16\-inch bolt hole areas on the
lower spar caps for fatigue cracking;
--Replacing any lower spar cap where fatigue cracking is found; and
--Reporting any fatigue cracking to FAA.
AD 97-13-11 incorrectly referenced the Ayres Model S2R-R1340
airplanes as Model S2R-1340R. AD 97-17-03 corrected the model
designation and retained the actions of AD 97-13-11.
What Has Happened Since AD 2000-11-16 To Initiate This Action?
Since AD 2000-11-16, FAA has identified additional airplanes with
the same type design that should be added to the Applicability of the
AD. The manufacturer has issued update service information that gives
the owners/operators of the affected airplanes an additional repair
option. We have also identified several minor typographical errors in
AD 2000-11-16.
Is There Service Information That Applies to This Subject?
Quality Aerospace (formerly Ayres Corporation) has issued these
service bulletins:
--Ayres Service Bulletin No. SB-AG-39, dated September 17, 1996;
--Ayres Custom Kit No. CK-AG-29, dated December 23, 1997; and
--Quality Aerospace Custom Kit No. CK-AG-30, dated December 6, 2001.
What Are the Provisions of This Service Information?
These service bulletins include procedures for:
--Inspecting the \1/4\-inch and \5/16\-inch bolt hole areas on the
lower spar caps for fatigue cracking;
--Reworking the spar cap if a small crack is found in the \1/4\-inch
spar cap hole;
--Replacing the butterfly center splice plate, part number 20211-3,
from the aft surface of the wing spar join area; and
--Installing a splice block that improves the chances of salvaging a
spar cap that has small cracks in the \1/4\-inch and \5/16\-inch bolt
holes.
The FAA's Determination and an Explanation of the Provisions of This
Proposed AD
What Has FAA Decided?
After examining the circumstances and reviewing all available
information related to the incidents described above, we have
determined that:
--The unsafe condition referenced in this document exists or could
develop on other Quality Aerospace S2R series and Model 600 S2D
airplanes of the same type design;
--The actions specified in the previously-referenced service
information should be accomplished on the affected airplanes; and
--AD action should be taken in order to correct this unsafe condition.
What Would This Proposed AD Require?
This proposed AD would supersede AD 2000-11-16 with a new AD that
would:
--Retain the repetitive inspections and replacement (if necessary)
requirements of AD 2000-11-16;
--Add an additional repair option of installing a splice block to
improve the chances of salvaging a spar cap that has small cracks in
the \1/4\-inch and \5/16\-inch bolt holes; and
--Add additional airplanes to the Applicability of the AD.
Cost Impact
How Many Airplanes Would This Proposed AD Impact?
We estimate that this proposed AD affects 1,015 airplanes in the
U.S. registry.
What Would be the Cost Impact of This Proposed AD on Owners/Operators
of the Affected Airplanes?
We estimate the following costs to accomplish each proposed
inspection:
----------------------------------------------------------------------------------------------------------------
Total cost per Total cost on U.S.
Labor cost Parts cost airplane operators
----------------------------------------------------------------------------------------------------------------
3 workhours x $60 = $180............................. $417 $597 1,015 x $597 = $605,955
----------------------------------------------------------------------------------------------------------------
We estimate the following costs to accomplish any necessary cold
work of bolt holes that would be required based on the results of the
proposed inspection. We have no way of determining the number of
airplanes that may need such repair:
----------------------------------------------------------------------------------------------------------------
Total cost per
Labor cost Parts cost airplane
----------------------------------------------------------------------------------------------------------------
1 workhour x $60= $60.......................................................... $100 $160
----------------------------------------------------------------------------------------------------------------
We estimate the following costs to accomplish any necessary
installation of a butterfly splice plate that would be required based
on the results of the proposed inspection. We have no way of
determining the number of airplanes that may need such installation:
----------------------------------------------------------------------------------------------------------------
Total cost per
Labor cost Parts cost airplane
----------------------------------------------------------------------------------------------------------------
70 workhours x $60 = $4,200.................................................... $700 $4,900
----------------------------------------------------------------------------------------------------------------
We estimate the following costs to accomplish any necessary reaming
of outer holes to \5/16\-inch diameter that would be required based on
the results of the proposed inspection. We have no way of determining
the number of airplanes that may need such repair:
[[Page 68049]]
----------------------------------------------------------------------------------------------------------------
Total cost per
Labor cost Parts cost airplane
----------------------------------------------------------------------------------------------------------------
1 workhour x $60 = $60......................................................... None $60
----------------------------------------------------------------------------------------------------------------
We estimate the following costs to accomplish any necessary
drilling and reaming of outer holes and adding three holes to install a
splice block that would be required based on the results of the
proposed inspection. We have no way of determining the number of
airplanes that may need such modification:
------------------------------------------------------------------------
Total cost per
Labor cost Parts cost airplane
------------------------------------------------------------------------
65 workhours x $60 = $3,900............. $4,100 $8,000
------------------------------------------------------------------------
We estimate the following costs to accomplish any necessary spar
cap replacement that would be required based on the results of the
proposed inspection. We have no way of determining the number of
airplanes that may need such replacement:
----------------------------------------------------------------------------------------------------------------
Parts cost per Total cost per
Labor cost per spar cap spar cap spar cap
----------------------------------------------------------------------------------------------------------------
200 workhours X $60 = $12,000.................................................. $2,316 $14,316
----------------------------------------------------------------------------------------------------------------
What Is the Difference Between the Cost Impact of This Proposed AD and
the Cost Impact of AD 2000-11-16?
The differences between this proposed AD and the cost impact of AD
2000-11-16 are:
--The addition of an optional repair to install a splice block; and
--The addition of 15 airplanes of similar design.
Regulatory Impact
Would This Proposed AD Impact Various Entities?
The regulations proposed herein would not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this proposed rule would not have federalism
implications under Executive Order 13132.
Would This Proposed AD Involve a Significant Rule or Regulatory Action?
For the reasons discussed above, I certify that this proposed
action: (1) Is not a ``significant regulatory action'' under Executive
Order 12866; (2) is not a ``significant rule'' under DOT Regulatory
Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if
promulgated, will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act. A copy of the draft regulatory
evaluation prepared for this action has been placed in the Rules
Docket. A copy of it may be obtained by contacting the Rules Docket at
the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2000-11-16, Amendment 39-11764 (65 FR 36055, June 7, 2000), and by
adding a new AD to read as follows:
** ** ** Quality Aerospace, Inc. (Ayres Corporation formerly held
Type Certificate (TC) No. A4SW): Docket No. 2001-CE-37-AD;
Supersedes AD 2000-11-16, Amendment 39-11764.
(a) What airplanes are affected by this AD? This AD affects the
following airplane models and serial numbers that are certificated
in any category:
------------------------------------------------------------------------
Model Serial Numbers Group
------------------------------------------------------------------------
(1) S-2R...................... 5000R through 5099R, except 1
5010R, 5031R, 5038R, 5047R, and
5085R.
(2) S2R-G1.................... G1-101 through G1-106........... 1
(3) S2R-R1820................. R1820-001 through R1820-035..... 1
(4) S2R-T15................... T15-001 through T15-033......... 1
(5) S2R-T34................... 6000R through 6049R, T34-001 1
through T34-143, T34-144, T34-
147 through T34-167, T34-171,
T34-180, and T34-181.
(6) S2R-G10................... G10-101 through G10-136, G10- 2
138, G10-140, and G10-141.
(7) S2R-G5.................... G5-101 through G5-105........... 2
(8) S2R-G6.................... G6-101 through G6-147........... 2
(9) S2RHG-T65................. T65-002 through T65-018......... 2
(10) S2R-R1820................ R1820-036....................... 2
(11) S2R-T34.................. T34-144, T34-146, T34-168, T34- 2
169, T34-172 through T34-179,
and T34-189 through T34-232,
and T34-234.
[[Page 68050]]
(12) S2R-T45.................. T45-001 through T45-014......... 2
(13) S2R-T65.................. T65-001 through T65-018......... 2
(14) 600 S2D.................. All serial numbers beginning 3
with 600-1311D.
(15) S-2R..................... 1380R and 1416R through 2592R... 3
(16) R1340.................... R1340-001 through R1340-035..... 3
(17) S2R-R3S.................. R3S-001 through R3S-011......... 3
(18) S2R-T11.................. T11-001 through T11-005......... 3
(19) S2R-G1................... G1-107, G1-108, and G1-109...... 4
(20) S2R-G10.................. G10-137, G10-139, and G10-142... 4
(21) S2R-T34.................. T34-225, T34-236, T34-237, and 4
T34-238.
(22) S2R-G1................... G1-110 through G1-115........... 5
(23) S2R-G10.................. G10-143 through G10-165......... 5
(24) S2R-G6................... G6-148 through G6-155........... 5
(25) S2RHG-T34................ T34HG-102....................... 5
(26) S2R-T15.................. T15-034 through T15-040......... 5
(27) S2R-T34.................. T34-239 through T34-270......... 5
(28) S2R-T45.................. T45-015......................... 5
(29) S2R...................... 5010R, 5031R, 5038R, 5047R, and 6
5085R.
------------------------------------------------------------------------
Note 1: The serial numbers of the Model S2R-T15 airplanes could
incorporate T15-xxx and T27-xxx. This AD applies to both of these
serial number designations as they are both Model S2R-T15 airplanes.
Note 2: The serial numbers of the Model S2R-T34 airplanes could
incorporate T34-xxx, T36-xxx, T41-xxx, or T42-xxx. This AD applies
to all of these serial number designations as they are all Model
S2R-T34 airplanes.
Note 3: Any Group 3 airplane that has been modified with a
hopper of a capacity more than 410 gallons, a piston engine greater
than 600 horsepower, or any gas turbine engine, makes the airplane a
Group 1 airplane for the purposes of this AD. Inspect the airplane
at the Group 1 compliance time specified in this AD.
(b) Who must comply with this AD? Anyone who wishes to operate
any of the airplanes identified in paragraph (a) of this AD must
comply with this AD.
(c) What problem does this AD address? The actions specified by
this AD are intended to detect and correct fatigue cracking of the
lower spar caps, which could result in the wing separating from the
airplane with consequent loss of control of the airplane.
(d) What actions must I accomplish to address this problem? To
address this problem, you must accomplish the following:
(1) Repetitively inspect, using magnetic particle, ultrasonic,
or eddy current procedures, the \1/4\-inch and \5/16\-inch bolt hole
areas on each lower spar cap for fatigue cracking. Reference
paragraph (e)(3) and (e)(4) of this AD (including all subparagraphs)
to obtain the initial and repetitive inspection compliance times.
(i) The cracks may emanate from the bolt hole on the face of the
spar cap or they may occur in the shaft of the hole.
(ii) You must inspect both of these areas.
(iii) If using the magnetic particle method for the inspection,
perform the inspection using the ``Inspection'' portion of the
``Accomplishment Instructions'' and ``Lower Splice Fitting Removal
and Installation Instructions'' in Ayres Service Bulletin No. SB-AG-
39, dated September 17, 1996. You must follow American Society for
Testing Materials (ASTM) E1444-94A, using wet particles meeting the
requirements of the Society for Automotive Engineers (SAE) AMS 3046.
The inspection must be performed by or supervised by a Level 2 or
Level 3 inspector certified for magnetic particle inspection method
using the guidelines established by the American Society for
Nondestructive Testing or MIL-STD-410. CAUTION: You must firmly
support the wings during the inspection to prevent movement of the
spar caps when the splice blocks are removed. This will allow easier
realignment of the splice block holes and the holes in the spar cap
for bolt insertion.
(iv) If using ultrasonic or eddy current methods for the
inspection, a procedure must be sent to the FAA Atlanta Aircraft
Certification Office for approval prior to performing the
inspection. Send your proposed procedure to the FAA Atlanta Aircraft
Certification Office (ACO), Attn: Cindy Lorenzen, One Crown Center,
1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia 30349. You are
not required to remove the splice block for either the ultrasonic or
eddy current inspections, unless corrosion is visible.
(2) If any cracking is found during any inspection required by
this AD, you must accomplish the following:
(i) Repair or replace:
(A) Use the cold work process to ream out small cracks as
defined in Ayres Service Bulletin No. SB-AG-39, dated September 17,
1996; or
(B) ream the \1/4\-inch bolt holes to \5/16\ inches diameter as
defined in Part I of Ayres Custom Kit No. CK-AG-29, dated December
23, 1997; or
(C) install Kaplan Splice Blocks as defined in Quality
Aerospace, Inc. Custom Kit No. CK-AG-30, dated December 6, 2001; or
(D) replace the affected spar cap in accordance with the
maintenance manual.
(ii) Submit a report of inspection findings to the Manager,
Atlanta ACO, One Crown Center, 1895 Phoenix Boulevard, Suite 450,
Atlanta, Georgia 30349; facsimile: (770) 703-6097. You must include:
(A) The airplane serial number and engine model number;
(B) The total number of flight hours on the lower spar cap that
is cracked;
(C) Time on the spar cap since last inspection, if applicable;
(D) The procedure (magnetic particle, ultrasonic, or eddy
current) used for the last inspection;
(E) Indicate if cold working has been accomplished or
modifications incorporated such as installation of big butterfly
plates;
(F) Indicate the time on the spar cap when the cold working or
modifications were accomplished; and
(G) Indicate which bolt hole is cracked and the length of the
crack.
Note 4: Information collection requirements contained in this
regulation have been approved by the Office of Management and Budget
(OMB) under the provisions of the Paperwork Reduction Act of 1980
(44 U.S.C. 3501 et seq.) and have been assigned OMB Control Number
2120-0056.
(e) What is the compliance time of this AD? The compliance times
for each of the actions of this AD are as follows:
(1) Any required repair or replacement: Prior to further flight
after the inspection where the crack(s) was/were found.
(2) Reporting requirement:
(i) Submit the report within 10 days after finding any crack(s)
during any inspection required by this AD.
(ii) For airplanes where cracking was found during any
inspection accomplished in accordance with AD 2000-11-16, which is
superseded by this AD; or by AD 97-17-03, which was superseded AD
2000-11-16; or by AD 97-13-11, which was superseded by AD 97-17-03,
submit the report within 10 days after the effective date of this
AD, unless already accomplished.
(3) Initial inspection: Required unless already accomplished
(compliance with AD 2000-11-16, or AD 97-17-03, or AD 97-13-11)
within 50 flight hours after the effective date of this AD or upon
the accumulation of these hours time-in-service (TIS) on each lower
spar cap, whichever occurs later:
------------------------------------------------------------------------
Airplane group Lower spar cap hours TIS
------------------------------------------------------------------------
(i) 1............................ 2,000.
(ii) 2........................... 2,200.
(iii) 3.......................... 6,400.
(iv) 4........................... 2,500.
[[Page 68051]]
(v) 5............................ 6,200.
(vi) 6........................... For S/N 5010R: 5,530.
For S/N 5038R: 5,900.
For S/N 5031R: 6,400.
For S/N 5047R: 6,400.
For S/N 5085R: 6,290.
------------------------------------------------------------------------
(4) Repetitive inspections: The following table gives the
required repetitive inspection intervals based on the work performed
and the method of inspection utilized. Each time is hours TIS after
the last inspection:
----------------------------------------------------------------------------------------------------------------
Magnetic
Work previously performed particle hours Ultrasonic Eddy current
TIS hours TIS hours TIS
----------------------------------------------------------------------------------------------------------------
(i) One of the following where the airplane does not have 500 550 700
butterfly plates, part number (P/N) 20211-09 and P/N 20211-11,
installed per CK-AG-29, Part II................................
(A) No cracks found previously on wing spar; or
(B) Small cracks repaired through cold work (or done as an
option if never cracked) accomplished per SB-AG-39; or
(C) Small cracks repaired through \1/4\-inch bolt hole
reamed to \5/16\ inches diameter (or done as an option if
never cracked) per CK-AG-29, Part I; or
(D) Small cracks repaired through previous Alternative
Methods of Compliance; or
(E) Small cracks repaired by installation of Kaplan Splice
Blocks, part number 22515-1/-3 or 88-251 (or done as an
option if never cracked) per CK-AG-30 and inspection of the
six outboard bolt holes on both lower spars is required
(ii) One of the following where the airplane has butterfly 900 950 1,250
plates, part number (P/N) 20211-09 and P/N 20211-11, installed
per CK-AG-29, Part II..........................................
(A) No cracks found previously on wing spar; or
(B) Small cracks repaired through cold work (or done as an
option if no cracks found) accomplished per SB-AG-39; or
(C) Small cracks repaired through \1/4\-inch bolt hole
reamed to \5/16\ inches diameter (or done as an option if
no cracks found) per CK-AG-29, Part I; or
(D) Small cracks repaired through previous Alternative
Methods of Compliance; or
(E) Small cracks repaired by installation of Kaplan Splice
Blocks, part number 22515-1/-3 or 88-251 (or done as an
option if never cracked) per CK-AG-30 and inspection of the
six outboard bolt holes on both lower spar caps is required
(iii) Cracked wing spar found during previous inspection with
wing spar replacement:
For all inspection methods (magnetic particle, ultrasonic,
or eddy current), time for initial and repetitive
inspection intervals start over when wing spar is replaced.
----------------------------------------------------------------------------------------------------------------
Note 5: Aircraft S/Ns T45-007DC and T45-010DC had modified
splice block assemblies installed at Ayres (Ayres/Kaplan Assembly
No. 88-251) and must still follow the repetitive inspection
intervals listed here.
Note 6: If a crack is found, the reaming associated with the
cold work process may remove a crack if it is small enough. Some
aircraft owners/operators were issued alternative methods of
compliance with AD 97-17-03 to ream the \1/4\-inch bolt hole to \5/
16\ inches diameter to remove small cracks. Ayres CK-AG-29, Part I,
also provides procedures to ream the \1/4\-inch bolt hole to \5/16\
inches diameter. If you use either of these two methods to remove
cracks and the airplane is reinspected immediately with no cracks
found, you may continue to follow the repetitive inspection
intervals listed above.
Note 7: Group 4 and Group 5 airplanes had the butterfly plates
installed at the factory and may follow the repetitive inspection
interval listed in paragraph (e)(4)(ii).
(f) Can I comply with this AD in any other way?
(1) You may use an alternative method of compliance or adjust
the compliance time if:
(i) Your alternative method of compliance provides an equivalent
level of safety; and
(ii) The Manager, Atlanta ACO, approves your alternative. Submit
your request through an FAA Principal Maintenance Inspector, who may
add comments and then send it to the Manager, Atlanta ACO.
(2) Alternative methods of compliance approved in accordance
with AD 2000-11-16, which is superseded by this AD, are approved as
alternative methods of compliance with this AD.
Note 8: This AD applies to each airplane identified in paragraph
(a) of this AD, regardless of whether it has been modified, altered,
or repaired in the area subject to the requirements of this AD. For
airplanes that have been modified, altered, or repaired so that the
performance of the requirements of this AD is affected, the owner/
operator must request approval for an alternative method of
compliance in accordance with paragraph (f) of this AD. The request
should include an assessment of the effect of the modification,
alteration, or repair on the unsafe condition addressed by this AD;
and, if you have not eliminated the unsafe condition, specific
actions you propose to address it.
(g) Where can I get information about any already-approved
alternative methods of compliance? Contact Cindy Lorenzen, Aerospace
Engineer, FAA, Aircraft Certification Office, One Crown Center, 1895
Phoenix Boulevard, suite 450, Atlanta, Georgia 30349; telephone:
(770) 703-6078; facsimile: (770) 703-6097.
(h) What if I need to fly the airplane to another location to
comply with this AD? The FAA can issue a special flight permit under
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate your airplane to a location where
you can accomplish the requirements of this AD provided that:
(1) The hopper is empty;
(2) Vne is reduced to 126 miles per hour (109 knots) indicated
airspeed (IAS); and
(3) Flight into known turbulence is prohibited.
(i) How do I get copies of the documents referenced in this AD?
You may get copies of the documents referenced in this AD from
Quality Aerospace, Inc., P.O. Box 3050, Albany, Georgia 31706-3050;
telephone: (229) 883-1440; facsimile: (229) 883-9790. You may view
these documents at FAA, Central Region, Office of the Regional
Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.
(j) Does this AD action affect any existing AD actions? This
amendment supersedes AD 2000-11-16, Amendment 39-11764.
Issued in Kansas City, Missouri, on October 31, 2002.
Michael Gallagher,
Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 02-28407 Filed 11-7-02; 8:45 am]
BILLING CODE 4910-13-P