[Federal Register: July 8, 1998 (Volume 63, Number 130)] [Rules and Regulations] [Page 36835-36836] From the Federal Register Online via GPO Access [wais.access.gpo.gov] [DOCID:fr08jy98-4] ----------------------------------------------------------------------- DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. 98-NM-95-AD; Amendment 39-10448; AD 98-07-26] RIN 2120-AA64 Airworthiness Directives; Boeing Model 767 Series Airplanes AGENCY: Federal Aviation Administration, DOT. ACTION: Final rule; correction. ----------------------------------------------------------------------- SUMMARY: This document corrects two typographical errors that appeared in airworthiness directive (AD) 98-07-26, which was published in the Federal Register on April 6, 1998 (63 FR 16681). The typographical errors resulted in a reference to an incorrect part number and incorrect section of the referenced service information. This AD is applicable to certain Boeing Model 767 series airplanes. This AD requires detailed visual inspection(s) for damage or chafing of certain electrical wire bundles and for clearance between the wire bundles and adjacent forward galley air chiller; and follow-on corrective actions. DATES: Effective April 21, 1998. The incorporation by reference of certain publications listed in the regulations was previously approved by the Director of the Federal Register as of April 21, 1998 (63 FR 16681, April 6, 1998). FOR FURTHER INFORMATION CONTACT: Elias Natsiopoulos, Aerospace Engineer, Systems and Equipment Branch, ANM-130S, FAA, Transport Airplane Directorate, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-1279; fax (425) 227-1181. SUPPLEMENTARY INFORMATION: Airworthiness Directive (AD) 98-07-26, amendment 39-10448, applicable to certain Boeing Model 767 series airplanes, was published in the Federal Register on April 6, 1998 (63 FR 16681). That AD requires detailed visual inspection(s) for damage or chafing of certain electrical wire bundles and for clearance between the wire bundles and adjacent forward galley air chiller; and follow-on corrective actions. As published, that AD contained two typographical errors in paragraphs (a)(1)(ii), (a)(2), (a)(3)(ii), and (a)(4). First, those paragraphs identified ``Section 20-00-11'' of the Boeing Standard Wiring Practices Manual as the appropriate source of service information for accomplishment of the actions. However, the correct section should have been identified as ``Section 20-10-11.'' Second, those paragraphs identified ``TFX-2X standard wall thickness (sleeve)'' as one of the appropriate materials to protect the bundles. However, part number (P/N) ``TFX-2X'' was indicated inadvertently in those paragraphs instead of the correct P/N ``TFE-2X.'' (In fact, P/N ``TFX- 2X'' does not exist.) Since no other part of the regulatory information has been changed, the final rule is not being republished. The effective date of this AD remains April 21, 1998. In final rule, FR Doc. 98-8705, published on April 6, 1998 (63 FR 16681), make the following corrections: Sec. 39.13 [Corrected] 1. On page 16683, in the first column, paragraph (a)(1)(ii) of AD 98-07-26 is corrected to read as follows: * * * * * (a) * * * (1) * * * (ii) Prior to further flight, install protective tape or sleeve over the wire bundles, in accordance with Section 20-10-11 of the Boeing Standard Wiring Practices Manual. Operators shall use one of the following materials to protect the bundles: RT876 (sleeve), TFE-2X standard wall thickness (sleeve), P-440 (tape), Scotch 70 (tape), or CHR-A-2005 (tape). * * * * * 2. On page 16683, in the first column, paragraph (a)(2) of AD 98- 07-26 is corrected to read as follows: * * * * * (a) * * * (2) If no damage or chafing is detected and inadequate clearance exists, prior to further flight, modify the routing of the wire bundles in accordance with the Boeing message, and install protective tape or sleeve over the wire bundles in accordance with Section 20-10-11 of the Boeing Standard Wiring Practices Manual. Operators shall use one of the following materials to protect the bundles: RT876 (sleeve), TFE-2X [[Page 36836]] standard wall thickness (sleeve), P-440 (tape), Scotch 70 (tape), or CHR-A-2005 (tape). * * * * * 3. On page 16683, in the first column, paragraph (a)(3)(ii) of AD 98-07-26 is corrected to read as follows: * * * * * (a) * * * (3) * * * (ii) Prior to further flight, install protective tape or sleeve over the wire bundles in accordance with Section 20-10-11 of the Boeing Standard Wiring Practices Manual. Operators shall use one of the following materials to protect the bundles: RT876 (sleeve), TFE-2X standard wall thickness (sleeve), P-440 (tape), Scotch 70 (tape), or CHR-A-2005 (tape). * * * * * 4. On page 16683, in the first and second columns, paragraph (a)(4) of AD 98-07-26 is corrected to read as follows: * * * * * (a) * * * (4) If damage or chafing is detected and inadequate clearance exists, prior to further flight, repair and modify the routing of the wire bundles in accordance with the Boeing message, and install protective tape or sleeve over the wire bundles in accordance with Section 20-10-11 of the Boeing Standard Wiring Practices Manual. Operators shall use one of the following materials to protect the bundles: RT876 (sleeve), TFE-2X standard wall thickness (sleeve), P-440 (tape), Scotch 70 (tape), or CHR-A-2005 (tape). * * * * * Issued in Renton, Washington, on June 29, 1998. Vi L. Lipski, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 98-17910 Filed 7-7-98; 8:45 am] BILLING CODE 4910-13-U