 |
|
 |
Home Page > Executive Branch > Code of Federal Regulations > Electronic Code of Federal Regulations
e-CFR Data is current as of November 3, 2008
TITLE 40--Protection of Environment
CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY
SUBCHAPTER U--AIR POLLUTION CONTROLS
PART 1065--ENGINE-TESTING PROCEDURES
Subpart A--APPLICABILITY AND GENERAL PROVISIONS
|
| Submitting information to EPA under this part. |
|
|
| Overview of this part 1065 and its relationship to the standard-setting part. |
|
|
| Approval of alternate procedures. |
|
|
| Overview of procedures for laboratory and field testing. |
|
|
| Units of measure and overview of calculations. |
|
Subpart B--EQUIPMENT SPECIFICATIONS
|
| Work inputs and outputs, accessory work, and operator demand. |
|
|
| Fuel properties and fuel temperature and pressure. |
|
|
| Engine cooling and lubrication. |
|
|
| Exhaust gas recirculation. |
|
|
| Dilution for gaseous and PM constituents. |
|
|
| Gaseous and PM probes, transfer lines, and sampling system components. |
|
|
| Batch sampling for gaseous and PM constituents. |
|
|
| PM-stabilization and weighing environments for gravimetric analysis. |
|
|
| PM-stabilization environment for in-situ analyzers. |
|
Subpart C--MEASUREMENT INSTRUMENTS
|
| Overview and general provisions. |
|
|
| Data updating, recording, and control. |
|
|
| Performance specifications for measurement instruments. |
|
|
| Work input and output sensors. |
|
|
| Pressure transducers, temperature sensors, and dewpoint sensors. |
|
|
| Dilution air and diluted exhaust flow meters. |
|
|
| Sample flow meter for batch sampling. |
|
|
| Nondispersive infra-red analyzer. |
|
|
| Flame-ionization detector. |
|
|
| Chemiluminescent detector. |
|
|
| Nondispersive ultraviolet analyzer. |
|
|
| Paramagnetic and magnetopneumatic Odetection analyzers. |
|
|
| Zirconia (ZrO2) analyzer. |
|
|
| PM inertial balance for field-testing analysis. |
|
Subpart D--CALIBRATIONS AND VERIFICATIONS
|
| Overview and general provisions. |
|
|
| Summary of required calibration and verifications. |
|
|
| Verifications for accuracy, repeatability, and noise. |
|
|
| Continuous gas analyzer system-response and updating-recording verification--general. |
|
|
| Continuous gas analyzer system-response and updating-recording verification--with humidified-response verification. |
|
|
| Pressure, temperature, and dewpoint calibration. |
|
|
| Exhaust-flow calibration. |
|
|
| Diluted exhaust flow (CVS) calibration. |
|
|
| CVS and batch sampler verification (propane check). |
|
|
| Sample dryer verification. |
|
|
| Vacuum-side leak verification. |
|
|
| H2O interference verification for CO2 NDIR analyzers. |
|
|
| H2O and CO2 interference verification for CO NDIR analyzers. |
|
|
| FID optimization and verification. |
|
|
| Non-stoichiometric raw exhaust FID O2 interference verification. |
|
|
| Nonmethane cutter penetration fractions. |
|
|
| CLD CO2 and H2O quench verification. |
|
|
| NDUV analyzer HC and H2O interference verification. |
|
|
| NO2-to-NO converter conversion verification. |
|
|
| PM balance verifications and weighing process verification. |
|
|
| Inertial PM balance verifications. |
|
Subpart E--ENGINE SELECTION, PREPARATION, AND MAINTENANCE
|
| Test engine preparation and maintenance. |
|
|
| Maintenance limits for stabilized test engines. |
|
|
| Durability demonstration. |
|
Subpart F--PERFORMING AN EMISSION TEST OVER SPECIFIED DUTY CYCLES
|
| Cycle-validation criteria for operation over specified duty cycles. |
|
|
| Pre-test verification procedures and pre-test data collection. |
|
|
| Engine starting, restarting, shutdown, and optional repeating of void discrete modes. |
|
|
| Validation of proportional flow control for batch sampling and minimum dilution ratio for PM batch sampling. |
|
|
| Gas analyzer range validation, drift validation, and drift correction. |
|
|
| PM sampling media (e.g., filters) preconditioning and tare weighing. |
|
|
| PM sample post-conditioning and total weighing. |
|
Subpart G--CALCULATIONS AND DATA REQUIREMENTS
|
| 1980 international gravity formula. |
|
|
| Flow meter calibration calculations. |
|
|
| SSV, CFV, and PDP molar flow rate calculations. |
|
|
| Amount of water in an ideal gas. |
|
|
| Chemical balances of fuel, intake air, and exhaust. |
|
|
| Removed water correction. |
|
|
| THC and NMHC determination. |
|
|
| THCE and NMHCE determination. |
|
|
| Dilution air background emission correction. |
|
|
| NOintake-air humidity and temperature corrections. |
|
|
| CLD quench verification calculations. |
|
|
| Buoyancy correction for PM sample media. |
|
Subpart H--ENGINE FLUIDS, TEST FUELS, ANALYTICAL GASES AND OTHER CALIBRATION STANDARDS
|
| General requirements for test fuels. |
|
|
| Residual and intermediate residual fuel. |
|
Subpart I--TESTING WITH OXYGENATED FUELS
|
| Response factor determination. |
|
Subpart J--FIELD TESTING AND PORTABLE EMISSION MEASUREMENT SYSTEMS
|
| PEMS auxiliary equipment for field testing. |
|
|
| PEMS Calibrations and verifications. |
|
|
| PEMS preparation for field testing. |
|
|
| Engine starting, restarting, and shutdown. |
|
|
| Emission test sequence for field testing. |
|
Subpart K--DEFINITIONS AND OTHER REFERENCE INFORMATION
|
| Symbols, abbreviations, acronyms, and units of measure. |
|
February 27, 2007< !-- #EndDate -- >-->
|
