OSHA eTools and Electronic Products for Compliance Assistance > OSHA e-HASP Software - Public Test Version...
|
Printing Instructions
|
|
|
e-HASP2 Quick Links |
|
|
|
OSHA e-HASP Software - Version 2.0 (e-HASP2), March 2006 |
OSHA conducts inspections of hazardous waste site activities.
During these inspections, deficiencies in written Health and Safety
Plans (HASP) are commonly found. These deficiencies generally indicate
a lack of knowledge and/or understanding of the required content of
the HASP. The most consistent deficiency is a lack of site-specificity
in the plans.
In the early 1990s, EPA's Environmental Response Team published a
DOS-based software package which generated a model HASP. It contained
some automatic fill options and simple decision logic, but was limited
in its programmed features and in its capacity to generate a site-specific HASP.
Based on field evidence, both Agencies became interested in updating
the original EPA software. As a result, the original e-HASP Program
(Version 1) using Windows-based software was developed and completed
in September, 2003. Since then, numerous comments were received to
improve the functionality and "user friendliness" of the software.
The updated e-HASP2 (Version 2) Program continues to use Windows-based software
and includes decision logic to assist the user in determining the
appropriate controls for health and safety hazards on their sites.
The integrated chemical database has been improved with more chemicals
and updated exposure limits. Some of the other notable upgrades for
e-HASP2 include: 1) upgrades to pick-lists, 2) function to add new
chemicals that are not in the chemical database, 3) function to export
reports to a word processor for editing, 4) new "preview chapter" button,
and 5) a newly designed job hazard analysis (JHA) chapter.
e-HASP2 is an electronic and interactive program that is intended to be
used by health and safety professionals to provide "model" language that
is acceptable to OSHA in preparing a site's HASP. These same professionals
can also draw on the chemical database and embedded decision logic to assist
them in identifying the hazards associated with site-specific contaminants
and in choosing effective site controls for worker protection.
The e-HASP2 software includes fifteen chapters and these are listed below.
- Organizational Structure
- Job Hazard Analysis
- Site Control
- Training Program
- Medical Surveillance Requirements
- Personal Protective Equipment (PPE)
- Exposure Monitoring
- Thermal Stress
- Spill Containment Program
- Decontamination Program
- Emergency Response Plan
- Standard Operating Procedures
- Confined Space Programs
- Hot Work
- Lockout/Tagout
|
|
e-HASP2 USER'S MANUAL
The user manual is posted as a PDF document.
Expected download time over a 56 kilo-baud per second (Kbps)
modem is approximately 2 minutes.
Downloading and Installing the e-HASP Software
To install the E-HASP2 Software, the following minimum system requirements and installation
requirements should be followed.
MINIMUM SYSTEM REQUIREMENTS
- Microsoft® Access 2000 or later
- Pentium III or higher processor
- Windows® 2000
- 256 MB RAM
- 30 MB Hard Disk Space
DOWNLOAD:
The approximate download time over a 56 Kbps modem is shown in parentheses.
COMMENTS/SUGGESTIONS
OSHA invites the public to download, use, and comment on this e-HASP2 software. OSHA has incorporated many good
suggestions from commenters who reviewed other OSHA software.
If you have suggestions, comments or need user support on this software, please submit them to: e-hasp@dol.gov.
If you have safety or health problems in your workplace, you should contact your local OSHA office.
e-HASP2 was developed by OSHA's DEP/OHE, in coordination with the EPA. E-HASP2 is programmed in Microsoft® Access using Visual Basic coding.
|
|