Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
[Federal Register: November 8, 2002 (Volume 67, Number 217)]
[Rules and Regulations]
[Page 68241-68447]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr08no02-12]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Parts 89, 90, 91, 94, 1048, 1051, 1065, and 1068
[AMS-FRL-7380-2]
RIN 2060-AI11
Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
AGENCY: Environmental Protection Agency (EPA).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: In this action, we are adopting emission standards for several
groups of nonroad engines that have not been subject to EPA emission
standards. These engines are large spark-ignition engines such as those
used in forklifts and airport ground-service equipment; recreational
vehicles using spark-ignition engines such as off-highway motorcycles,
all-terrain vehicles, and snowmobiles; and recreational marine diesel
engines. Nationwide, these engines and vehicles cause or contribute to
ozone, carbon-monoxide, and particulate-matter nonattainment, as well
as other types of pollution impacting human health and welfare.
We expect that manufacturers will be able to maintain or even
improve the performance of their products when producing engines and
equipment meeting the new standards. Many engines will substantially
reduce their fuel consumption, partially or completely offsetting any
costs associated with the emission standards. Overall, the gasoline-
equivalent fuel savings associated with the anticipated changes in
technology resulting from this rule are estimated to be about 800
million gallons per year once the program is fully phased in. Health
and environmental benefits from the controls included in today's rule
are estimated to be approximately $8 billion per year once the controls
are fully phased in. There are also several provisions to address the
unique limitations of small-volume manufacturers.
DATES: This final rule is effective January 7, 2003.
The incorporation by reference of certain publications listed in
this regulation is approved by the Director of the Federal Register as
of January 7, 2003.
ADDRESSES: Materials relevant to this rulemaking are contained in
Public Docket Numbers A-98-01 and A-2000-01 at the following address:
EPA Docket Center (EPA/DC), Public Reading Room, Room B102, EPA West
Building, 1301 Constitution Avenue, NW., Washington DC. The EPA Docket
Center Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday
through Friday, except on government holidays. You can reach the
Reading Room by telephone at (202) 566-1742, and by facsimile at (202)
566-1741. The telephone number for the Air Docket is (202) 566-1742.
You may be charged a reasonable fee for photocopying docket materials,
as provided in 40 CFR part 2.
For further information on electronic availability of this action,
see SUPPLEMENTARY INFORMATION below.
FOR FURTHER INFORMATION CONTACT: U.S. EPA, Office of Transportation and
Air Quality, Assessment and Standards Division hotline, (734) 214-4636,
asdinfo@epa.gov; Alan Staut, (734) 214-4805.
SUPPLEMENTARY INFORMATION:
Regulated Entities
This action will affect companies that manufacture or introduce
into commerce any of the engines or vehicles subject to emission
standards. These include: spark-ignition industrial engines such as
those used in forklifts and compressors; recreational vehicles such as
off-highway motorcycles, all-terrain vehicles, and snowmobiles; and
recreational marine diesel engines. This action will also affect
companies buying engines for installation in nonroad equipment. There
are also requirements that apply to those who rebuild any of the
affected nonroad engines. Regulated categories and entities include:
----------------------------------------------------------------------------------------------------------------
NAICS Codes Examples of potentially regulated
Category a SIC Codes b entities
----------------------------------------------------------------------------------------------------------------
Industry................................... 333618 3519 Manufacturers of new nonroad spark-
ignition engines, new marine engines.
Industry................................... 333111 3523 Manufacturers of farm equipment.
Industry................................... 333112 3531 Manufacturers of construction
equipment, recreational marine
vessels.
Industry................................... 333924 3537 Manufacturers of industrial trucks.
Industry................................... 811310 7699 Engine repair and maintenance.
Industry................................... 336991 ............ Motorcycle manufacturers.
Industry................................... 336999 ............ Snowmobiles and all-terrain vehicle
manufacturers.
Industry................................... 421110 ............ Independent Commercial Importers of
Vehicles and Parts.
----------------------------------------------------------------------------------------------------------------
\a\ North American Industry Classification System (NAICS)
\b\ Standard Industrial Classification (SIC) system code.
This list is not intended to be exhaustive, but rather provides a
guide regarding entities likely to be regulated by this action. To
determine whether this action regulates particular activities, you
should carefully examine the regulations. You may direct questions
regarding the applicability of this action to the person listed in FOR
FURTHER INFORMATION CONTACT.
Obtaining Electronic Copies of the Regulatory Documents
The preamble, regulatory language, Final Regulatory Support
Document, and other rule documents are also available electronically
from the EPA Internet web site. This service is free of charge, except
for any cost incurred for internet connectivity. The electronic version
of this final rule is made available on the day of publication on the
primary web site listed below. The EPA Office of Transportation and Air
Quality also publishes Federal Register notices and related documents
on the secondary web site listed below.
1. http://www.epa.gov/fedrgstr/EPA-AIR/ (either select desired
date or use Search feature)
2. http://www.epa.gov/otaq/ (look in What's New or under the specific
rulemaking topic)
Please note that due to differences between the software used to
develop the documents and the software into which the document may be
downloaded, format changes may occur.
Table of Contents
I. Introduction
A. Overview
B. How Is This Document Organized?
C. What Categories of Vehicles and Engines Are Covered in This
Final Rule?
D. What Requirements Are We Adopting?
E. Why Is EPA Taking This Action?
[[Page 68243]]
II. Nonroad: General Provisions
A. Scope of Application
B. Emission Standards and Testing
C. Demonstrating Compliance
D. Other Concepts
III. Recreational Vehicles and Engines
A. Overview
B. Engines Covered by This Rule
C. Emission Standards
D. Testing Requirements
E. Special Compliance Provisions
F. Technological Feasibility of the Standards
IV. Permeation Emission Control
A. Overview
B. Vehicles Covered by This Provision
C. Permeation Emission Standards
D. Testing Requirements
E. Special Compliance Provisions
F. Technological Feasibility
V. Large Spark-ignition (SI) Engines
A. Overview
B. Large SI Engines Covered by This Rule
C. Emission Standards
D. Testing Requirements and Supplemental Emission Standards
E. Special Compliance Provisions
F. Technological Feasibility of the Standards
VI. Recreational Marine Diesel Engines
A. Overview
B. Engines Covered by This Rule
C. Emission Standards for Recreational Marine Diesel Engines
D. Testing Equipment and Procedures
E. Special Compliance Provisions
F. Technical Amendments
G. Technological Feasibility
VII. General Nonroad Compliance Provisions
A. Miscellaneous Provisions (Part 1068, Subpart A)
B. Prohibited Acts and Related Requirements (Part 1068, Subpart
B)
C. Exemptions (Part 1068, Subpart C)
D. Imports (Part 1068, Subpart D)
E. Selective Enforcement Audit (Part 1068, Subpart E)
F. Defect Reporting and Recall (Part 1068, Subpart F)
G. Hearings (Part 1068, Subpart G)
VIII. General Test Procedures
A. General Provisions
B. Laboratory Testing Equipment
C. Laboratory Testing Procedures
D. Other Testing Procedures
IX. Projected Impacts
A. Environmental Impact
B. Cost Estimates
C. Cost Per Ton of Emissions Reduced
D. Economic Impact Analysis
E. Do the Benefits Outweigh the Costs of the Standards?
X. Public Participation
XI. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
B. Paperwork Reduction Act
C. Regulatory Flexibility Act (RFA), as Amended by the Small
Business Regulatory Enforcement Fairness Act of 1996 (SBREFA), 5
U.S.C. 601 et seq.
D. Unfunded Mandates Reform Act
E. Executive Order 13132: Federalism
F. Executive Order 13175: Consultation and Coordination With
Indian Tribal Governments
G. Executive Order 13045: Protection of Children From
Environmental Health and Safety Risks
H. Executive Order 13211: Actions That Significantly Affect
Energy Supply, Distribution, or Use
I. National Technology Transfer and Advancement Act
J. Congressional Review Act
K. Plain Language
I. Introduction
A. Overview
Emissions from the engines regulated in this rule contribute to
serious air-pollution problems, and will continue to do so in the
future absent regulation. These air pollution problems include exposure
to carbon monoxide (CO), ground-level ozone, and particulate matter
(PM), which can cause serious health problems, including premature
mortality and respiratory problems. Fine PM has also been associated
with cardiovascular problems, such as heart rate variability and
changes in fibrinogen (a blood clotting factor) levels, and hospital
admissions and mortality related to cardiovascular diseases. These
emissions also contribute to other serious environmental problems,
including visibility impairment and ecosystem damage. In addition, many
of the hydrocarbon (HC) pollutants emitted by these engines are air
toxics.
This rule addresses these air-pollution concerns by adopting
national emission standards for several types of nonroad engines and
vehicles that are currently unregulated. These include large spark-
ignition engines used in industrial and commercial applications such as
those used in forklifts and airport equipment; recreational spark-
ignition vehicles such as off-highway motorcycles, all-terrain
vehicles, and snowmobiles; and recreational marine diesel engines.\1\
These new standards are a continuation of the process of establishing
emission standards for nonroad engines and vehicles, under Clean Air
Act section 213(a).
---------------------------------------------------------------------------
\1\ Diesel-cycle engines, referred to simply as ``diesel
engines'' in this document, may also be referred to as compression-
ignition (or CI) engines. These engines typically operate on diesel
fuel, but other fuels may also be used. Otto-cycle engines (referred
to here as spark-ignition or SI engines) typically operate on
gasoline, liquefied petroleum gas, or natural gas.
---------------------------------------------------------------------------
We conducted a study of emissions from nonroad engines, vehicles,
and equipment in 1991, as directed by the Clean Air Act, section 213(a)
(42 U.S.C. 7547(a)). Based on the results of that study, we determined
that emissions of oxides of nitrogen (NOX), volatile organic
compounds, and CO from nonroad engines and equipment contribute
significantly to ozone and CO concentrations in more than one
nonattainment area (59 FR 31306, June 17, 1994). Given this
determination, section 213(a)(3) of the Act requires us to establish
(and from time to time revise) emission standards for those classes or
categories of new nonroad engines, vehicles, and equipment that in our
judgment cause or contribute to such air pollution. We have determined
that the engines covered by this final rule cause or contribute to such
air pollution (see the final finding for recreational vehicles and
nonroad spark-ignition engines over 19 kW published on December 7, 2000
(65 FR 76790), the final rule for marine diesel engines published on
December 29, 1999 (64 FR 73301)\2\, Section II of the preamble to the
proposed rule (66 FR 51098, October 5, 2001), this preamble, and the
Final Regulatory Support Document).
---------------------------------------------------------------------------
\2\ This rule also found that PM emissions from marine diesel
engines contribute to PM nonattainment.
---------------------------------------------------------------------------
Where we determine that other emissions from new nonroad engines,
vehicles, or equipment significantly contribute to air pollution that
may reasonably be anticipated to endanger public health or welfare,
section 213(a)(4) of the Act authorizes EPA to establish (and from time
to time revise) emission standards from those classes or categories of
new nonroad engines, vehicles, and equipment that cause or contribute
to such air pollution. Pursuant to section 213(a)(4) of the Act, we are
finalizing a finding that emissions from new nonroad engines, including
construction equipment, farm tractors, boats, locomotives, marine
engines, nonroad spark-ignition engines over 19 kW, recreational
vehicles (including off-highway motorcycles, all-terrain-vehicles, and
snowmobiles), significantly contribute to regional haze and visibility
impairment in federal Class I areas and where people live, work and
recreate. These engines, particularly recreational vehicles such as
snowmobiles, are significant emitters of pollutants that are known to
impair visibility in federal Class I areas (see Section I.E of this
preamble and the Final Regulatory Support Document). We have also
determined that engines covered by this final rule, particularly
recreational vehicles including snowmobiles, contribute to such
pollution. Thus, we are finalizing HC standards for snowmobiles to
reduce PM-related visibility impairment.
[[Page 68244]]
B. How Is This Document Organized?
This final rule covers engines and vehicles that vary in design and
use, and many readers may be interested in only one or two of the
applications. We have grouped engines by common application (for
example, recreational land-based engines, marine diesel recreational
engines, large spark-ignition engines used in commercial applications).
This document is organized in a way that allows each reader to focus on
the applications of particular interest.
Section II describes general provisions that are relevant to all of
the nonroad engines covered by this rulemaking. Section III through VI
present information specific to each of the affected nonroad
applications, including standards, effective dates, testing
information, and other specific requirements.
Sections VII and VIII describe a wide range of compliance and
testing provisions that apply generally to engines and vehicles from
all the nonroad engine and vehicle categories included in this
rulemaking. Several of these provisions apply not only to
manufacturers, but also to equipment manufacturers installing certified
engines, remanufacturing facilities, operators, and others. Therefore,
all affected parties should read the information contained in these
sections.
Section IX summarizes the projected impacts and a discussion of the
benefits of this rule. Finally, Sections X and XI contain information
about public participation and various administrative requirements.
The remainder of this section summarizes the new requirements and
the air quality need for the rulemaking.
C. What Categories of Vehicles and Engines Are Covered in This Final
Rule?
This final rule establishes regulatory programs for new nonroad
vehicles and engines not yet subject to EPA emission standards,
including the following engines:
[sbull]
Land-based spark-ignition recreational engines, including
those used in snowmobiles, off-highway motorcycles, and all-terrain
vehicles. For the purpose of this rule, we are calling this group of
engines ``recreational vehicles,'' even though all-terrain vehicles can
be used for commercial purposes.
[sbull]
Land-based spark-ignition engines rated over 19 kW,
including engines used in forklifts, generators, airport baggage tow
trucks, and various farm, construction, and industrial equipment. This
category also includes auxiliary marine engines, but does not include
propulsion marine engines or engines used in recreational vehicles. For
purposes of this rule, we refer to this category as ``Large SI
engines.''
[sbull]
Recreational marine diesel engines.
This final rule covers new engines that are used in the United
States, whether they are made domestically or imported.\3\ A more
detailed discussion of the meaning of the terms ``new'' and
``imported'' that help define the scope of application of this rule is
in Section II of this preamble.
---------------------------------------------------------------------------
\3\ For this final rule, we consider the United States to
include the States, the District of Columbia, the Commonwealth of
Puerto Rico, the Commonwealth of the Northern Mariana Islands, Guam,
American Samoa, the U.S. Virgin Islands, and the Trust Territory of
the Pacific Islands.
---------------------------------------------------------------------------
D. What Requirements Are We Adopting?
The fundamental requirement for nonroad engines and vehicles is
meeting EPA's emission standards. Section 213(a)(3) of the Act requires
that standards to control emissions related to ozone or CO achieve the
greatest degree of emission reduction achievable through the
application of technology that will be available, giving appropriate
consideration to cost, noise, energy, and safety factors. Section 213
(a)(4) of the Act requires that standards for emissions related to
other air pollution problems be appropriate and take into account
costs, noise, safety, and energy impacts of applying technology that
will be available. Other requirements such as applying for
certification, labeling engines, and meeting warranty requirements
define a process for implementing the program in an effective way.
With regard to Large SI engines, we are adopting a two-phase
program. The first phase of the standards go into effect in 2004 and
are the same as those adopted in October 1998 by the California Air
Resources Board for 2004. These standards will reduce combined HC and
NOX emissions by nearly 75 percent, based on emission
measurements during steady-state operation. In 2007, we supplement
these standards by setting limits that will require optimizing the same
technologies and will base emission measurements on a transient test
cycle. New requirements for evaporative emissions and engine
diagnostics also start in 2007.
For recreational vehicles, we are adopting separate emission
standards for snowmobiles, off-highway motorcycles, and all-terrain
vehicles. For snowmobiles, we are adopting a first phase of standards
for HC and CO emissions based on a mixture of technologies ranging from
clean carburetion and engine modifications to direct fuel injection
two-stroke technology and some conversion to four-stroke engines, and
second and third phases of emission standards for snowmobiles that will
involve significant use of direct fuel injection two-stroke technology
and conversion to four-stroke engines. For off highway motorcycles and
all-terrain vehicles, we are adopting standards based mainly on moving
these engines from two-stroke to four-stroke technology with the use of
some secondary air injection. We are also adopting requirements to
address permeation emissions from all three types of recreational
vehicles.
The emission standards for recreational marine diesel engines are
comparable to those already established for commercial marine diesel
engines. Manufacturers generally have additional time to meet emission
standards for the recreational models and several specific rulemaking
provisions are tailored to the unique characteristics of these engines.
We are also adopting more stringent voluntary Blue Sky Series
emission standards for recreational marine diesel engines and Large SI
engines. Blue Sky Series emission standards are more stringent than the
mandatory emission standards and are intended to encourage the
introduction and more widespread use of low-emission technologies.
Manufacturers may be motivated to exceed emission requirements either
to gain early experience with certain technologies or as a response to
market demand or local government programs. For recreational vehicles,
we are not adopting voluntary standards but rather providing consumers
with consumer labeling, which will provide information and opportunity
to buy lower-emissions models.
We have also conducted extensive analysis on the costs and benefits
of this rulemaking effort, with specific details found in Section IX
below and in the Final Regulatory Support Document. In summary, we
estimate that annually, the cost to manufacturers is approximately $210
million, the social gain is approximately $550 million, and the
quantified benefits are approximately $8 billion. Social gain is
defined as the economic cost of the rule minus the estimated fuels
savings. Quantified benefits reflect the health benefits primarily
associated with particulate matter controls.
E. Why Is EPA Taking This Action?
There are important public health and welfare reasons supporting
the new
[[Page 68245]]
emission standards. As described below and in the Final Regulatory
Support Document, these engines contribute to air pollution that causes
public health and welfare problems.
Nationwide, these engines and vehicles are a significant source of
mobile source air pollution. As described below, of all mobile source
emissions in 2000 they accounted for about 9 percent of HC emissions, 4
percent of CO emissions, 3 percent of NOX emissions, and 2
percent of direct PM emissions. The emissions from Large SI engines
contributed 2 to 3 percent of the HC, NOX, and CO emissions
from mobile sources in 2000. Recreational vehicles by themselves
account for about 6 percent of national mobile source HC emissions and
about 2 percent of national mobile source CO emissions. By reducing
these emissions, the standards will aid states facing ozone and CO air
quality problems, which can cause a range of adverse health effects,
especially in terms of respiratory disease and related illnesses. The
engine categories subject to this rule contribute to regional haze and
visibility impairment in Class I areas and near where people live, work
and recreate. Within national parks, emissions from snowmobiles in
particular contribute to ambient concentrations of fine PM, a leading
cause of visibility impairment. States are required to develop plans to
address visibility impairment in national parks, and the reductions
required in this rule would assist states in those efforts.
The standards will also help reduce acute exposure to CO and air
toxics for forklift operators, equipment users or riders, national and
state park attendants, and other people who may be at particular risk
because they operate or work or are otherwise in close proximity to
this equipment due to their occupation or as riders. Emissions from
these vehicles and equipment can be very high on a per-engine basis. In
addition, the equipment using these engines (especially forklifts) is
often operated in enclosed areas. Similarly, exposure to CO and air
toxics can be intensified for snowmobile riders who follow a group of
other riders along a trail, since those riders are exposed to the
emissions of all the other snowmobiles riding ahead.
When the emission standards are fully implemented in 2030, we
expect a 75-percent reduction in HC emissions, 82-percent reduction in
NOX emissions, and 61-percent reduction in CO emissions, and
a 60-percent reduction in direct PM emissions from these engines,
equipment, and vehicles (see Section IX below). These emission
reductions will reduce ambient concentrations of CO, ozone, and PM
fine; fine particles are a public health concern and contributes to
visibility impairment. The standards will also reduce exposure for
people who operate or who work with or are otherwise in close proximity
to these engines and vehicles.
We believe technology can be applied to these engines that will
reduce emissions of these harmful pollutants. Manufacturers can reduce
two-stroke engine emissions by improving fuel management and
calibration. This can be achieved by making improvements to carbureted
fuel systems and/or converting to electronic and direct fuel injection.
In addition, many of the existing two-stroke engines in these
categories can be converted to four-stroke technology. Finally, there
are modifications that can be made to four-stroke engines, often short
of requiring catalysts, that can reduce emissions even further.
1. Health and Welfare Effects
Exposure to CO, ground-level ozone, and PM can cause serious
respiratory problems, including premature mortality and respiratory
problems. Fine PM has also been associated with cardiovascular
problems, such as heart rate variability and fibrinogen (a blood
clotting factor) levels, and hospital admissions and mortality related
to cardiovascular diseases. These emissions also contribute to other
serious environmental problems, including visibility impairment and
ecosystem damage. In addition, some of the HC pollutants emitted by
these engines are air toxics. (The health and welfare effects are
described in more detail in the Final Regulatory Support Document.)
CO enters the bloodstream through the lungs and reduces the
delivery of oxygen to the body's organs and tissues. The health threat
from CO is most serious for those who suffer from cardiovascular
disease, particularly those with angina or peripheral vascular disease.
Healthy individuals also are affected, but only at higher CO levels.
Exposure to elevated CO levels is associated with impairment of visual
perception, work capacity, manual dexterity, learning ability and
performance of complex tasks.
Exposures to ozone has been linked to increased hospital admissions
and emergency room visits for respiratory problems.\4\ Repeated
exposure to ozone can increase susceptibility to respiratory infection
and lung inflammation. It can aggravate preexisting respiratory
diseases, such as asthma. Prolonged (6 to 8 hours), repeated exposure
to ozone can cause inflammation of the lung, impairment of lung defense
mechanisms, and possibly irreversible changes in lung structure, which
over time could lead to premature aging of the lungs and/or chronic
respiratory illnesses such as emphysema and chronic bronchitis.
Children, the elderly, asthmatics and outdoor workers are most at risk
from ozone exposure. Evidence also exists of a possible relationship
between daily increases in ozone levels and increases in daily
mortality levels. In addition to human health effects, ozone adversely
affects crop yield, vegetation and forest growth, and the durability of
materials.
---------------------------------------------------------------------------
\4\ U.S. EPA Review of the National Ambient Air Quality
Standards for Ozone: Policy Assessment of Scientific and Technical
Information OAQPS Staff Paper. EPA-452/R-96-007. June 1996. A copy
of this document can be found in Docket A-99-06, Document II-A-22.
---------------------------------------------------------------------------
PM, like ozone, has been linked to a range of serious respiratory
health problems.\5\ The key health effects associated with ambient
particulate matter include premature mortality, aggravation of
respiratory and cardiovascular disease (as indicated by increased
hospital admissions and emergency room visits, school absences, work
loss days, and restricted activity days), aggravated asthma, acute
respiratory symptoms, including aggravated coughing and difficult or
painful breathing, chronic bronchitis, and decreased lung function that
can be experienced as shortness of breath. Observable human non-cancer
health effects associated with exposure to diesel PM include some of
the same health effects reported for ambient PM such as respiratory
symptoms (cough, labored breathing, chest tightness, wheezing), and
chronic respiratory disease (cough, phlegm, chronic bronchitis and
suggestive evidence for decreases in pulmonary function). Symptoms of
immunological effects such as wheezing and increased allergenicity are
also seen.
---------------------------------------------------------------------------
\5\ U.S. EPA Review of the National Ambient Air Quality
Standards for Particulate Matter: Policy Assessment of Scientific
and Technical Information OAQPS Staff Paper. EPA-452/R-96-013. 1996.
Docket Number A-99-06, Documents Nos. II-A-18, 19, 20, and 23. The
particulate matter air quality criteria documents are also available
at http://www.epa.gov/ncea/partmatt.htm.
---------------------------------------------------------------------------
PM also causes adverse impacts to the environment. Fine PM is the
major cause of reduced visibility in parts of the United States,
including many of our national parks and in places where people live
and work. Visibility effects are manifest in two principal ways: (1) as
local impairment (for example,
[[Page 68246]]
localized hazes and plumes) and (2) as regional haze. The emissions
from engines covered by this rule can contribute to both types of
visibility impairment.
The engines covered by this rule also emit air toxics that are
known or suspected human or animal carcinogens, or have serious non-
cancer health effects. These include benzene, 1,3-butadiene,
formaldehyde, acetaldehyde, and acrolein.
2. What Is the Inventory Contribution From the Nonroad Engines and
Vehicles That Would Be Subject to This Rule?
The contribution of emissions from the nonroad engines and vehicles
that will be subject to this final rule to the national inventories of
pollutants is considerable. To estimate nonroad engine and vehicle
emission contributions, we used the latest version of our NONROAD
emissions model, updated with information received during the public
comment period. This model computes nationwide, state, and county
emission levels for a wide variety of nonroad engines, and uses
information on emission rates, operating data, and population to
determine annual emission levels of various pollutants. A more detailed
description of the model and our estimation methodology can be found in
the Chapter 6 of the Final Regulatory Support Document.
Baseline emission inventory estimates for the year 2000 for the
categories of engines and vehicles covered by this rule are summarized
in Table I.E-1. This table shows the relative contributions of the
different mobile source categories to the overall national mobile
source inventory. Of the total emissions from mobile sources, the
categories of engines and vehicles covered by this rule contribute
about 9 percent, 3 percent, 4 percent, and 2 percent of HC,
NOX, CO, and PM emissions, respectively, in the year 2000.
The results for Large SI engines indicate they contribute approximately
2 to 3 percent to HC, NOX, and CO emissions from mobile
sources. The results for land-based recreational engines reflect the
impact of the significantly different emissions characteristics of two-
stroke engines. These engines are estimated to contribute about 6
percent of HC emissions and 2 percent of CO from mobile sources.
Recreational marine diesel engines contribute less than 1 percent to
NOX mobile source inventories. When only nonroad emissions
are considered, the engines and vehicles that will be subject to the
standards account for a larger share.
Our draft emission projections for 2020 and 2030 for the nonroad
engines and vehicles subject to this rule show that emissions from
these categories are expected to increase over time if left
uncontrolled. The projections for 2020 and 2030 are summarized in
Tables I.E-2 and I.E-3, respectively. The projections for 2020 and 2030
indicate that the categories of engines and vehicles covered by this
rule are expected to contribute approximately 25 percent, 10 percent, 5
percent, and 5 percent of mobile source HC, NOX, CO, and PM
emissions, respectively, if left uncontrolled. Engine population growth
and the effects of other regulatory control programs are factored into
these projections. The relative importance of uncontrolled nonroad
engines in 2020 and 2030 is higher than the projections for 2000
because there are already emission-control programs in place for the
other categories of mobile sources which are expected to reduce their
emission levels. The effectiveness of all control programs is offset by
the anticipated growth in engine populations.
Regarding PM specifically, this information and information in
Section I.3(ii) below show that the engines being regulated in this
rule, snowmobiles and other recreational vehicles in particular,
contribute to PM concentrations that may reasonably be anticipated to
endanger public health and welfare both because of the health effects
associated with PM and because of the effects on visibility discussed
below.
Table I.E-1.--Modeled Annual Emission Levels for Mobile Source Categories in 2000
[Thousand short tons]
--------------------------------------------------------------------------------------------------------------------------------------------------------
NOX HC CO PM
---------------------------------------------------------------------------------------
Category Percent Percent Percent Percent
1000 tons of mobile 1000 tons of mobile 1000 tons of mobile 1000 tons of mobile
source source source source
--------------------------------------------------------------------------------------------------------------------------------------------------------
Total for engines subject to this final rule[hairsp][hairsp]*... 351 2.6 645 8.8 2,860 3.8 14.6 2.1
============
Highway Motorcycles............................................. 8 0.1 84 1.2 331 0.4 0.4 0.1
Nonroad Industrial SI £19 kW[hairsp][hairsp]*......... 308 2.3 226 3.1 1,734 2.3 1.6 0.2
Recreational SI[hairsp][hairsp]*................................ 5 0.0 418 5.7 1,120 1.5 12.0 1.7
Recreational Marine Diesel[hairsp][hairsp]*..................... 38 0.3 1 0.0 6 0.0 1 0.1
Marine SI Evap.................................................. 0 0.0 100 1.4 0 0.0 0 0.0
Marine SI Exhaust............................................... 32 0.2 708 9.7 2,144 2.8 38 5.4
Nonroad SI <19 kW............................................... 106 0.8 1,460 20.0 18,359 24.3 50 7.1
Nonroad diesel.................................................. 2,625 19.5 316 4.3 1,217 1.6 253 35.9
Commercial Marine Diesel........................................ 963 7.2 30 0.4 127 0.2 41 5.8
Locomotive...................................................... 1,192 8.9 47 0.6 119 0.2 30 4.3
------------
Total Nonroad................................................... 5,269 39 3,305 45 24,826 33 427 60
Total Highway................................................... 7,981 59 3,811 52 49,813 66 240 34
Aircraft........................................................ 178 1 183 3 1,017 1 39 6
------------
Total Mobile Sources............................................ 13,428 100 7,300 100 75,656 100 706 100
============
Total Man-Made Sources.......................................... 24,532 ......... 18,246 ......... 97,735 ......... 3,102 .........
============
Mobile Source percent of Total Man-Made Sources................. 55 ......... 40 ......... 77 ......... 23
--------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 68247]]
Table I.E-2.--Modeled Annual Baseline Emission Levels for Mobile Source Categories in 2020
[thousand short tons]
--------------------------------------------------------------------------------------------------------------------------------------------------------
NOX HC CO PM
---------------------------------------------------------------------------------------
Category Percent Percent Percent Percent
1000 tons of mobile 1000 tons of mobile 1000 tons of mobile 1000 tons of mobile
source source source source
--------------------------------------------------------------------------------------------------------------------------------------------------------
Total for engines subject to this final rule*................... 547 8.8 1,305 24.1 4,866 5.6 34.1 5.2
============
Highway Motorcycles............................................. 14 0.2 142 2.6 572 0.7 0.8 0.1
Nonroad Industrial SI £ 19 kW*........................ 472 7.6 318 5.9 2,336 2.7 2.3 0.4
Recreational SI*................................................ 14 0.2 985 18.2 2,521 2.9 30.2 4.6
Recreational Marine Diesel*..................................... 61 1.0 2 0.0 9 0.0 1.6 0.2
Marine SI Evap.................................................. 0 0.0 114 2.1 0 0.0 0 0.0
Marine SI Exhaust............................................... 58 0.9 284 5.2 1,985 2.3 28 4.3
Nonroad SI < 19 Kw.............................................. 106 1.7 986 18.2 27,352 31.7 77 11.8
Nonroad Diesel.................................................. 1,791 28.8 142 2.6 1,462 1.7 261 40.0
Commercial Marine Diesel........................................ 819 13.2 35 0.6 160 0.2 46 7.0
Locomotive...................................................... 611 9.8 35 0.6 119 0.1 21 3.2
------------
Total Nonroad................................................... 3,932 63 2,901 54 35,944 42 467 71
Total Highway................................................... 2,050 33 2,276 42 48,906 56 145 22
Aircraft........................................................ 232 4 238 4 1,387 2 43 7
------------
Total Mobile Sources............................................ 6,214 100 5,415 100 86,237 100 655 100
============
Total Man-Made Sources.......................................... 16,190 ......... 15,475 ......... 109,905 ......... 3,039 .........
============
Mobile Source percent of Total Man-Made Sources................. 38 ......... 35 ......... 79 ......... 22 .........
--------------------------------------------------------------------------------------------------------------------------------------------------------
Table I.E-3.--Modeled Annual Emission Levels for Mobile Source Categories in 2030
[Thousand short tons]
--------------------------------------------------------------------------------------------------------------------------------------------------------
NOX HC CO PM
---------------------------------------------------------------------------------------
Category Percent Percent Percent Percent
1000 tons of mobile 1000 tons of mobile 1000 tons of mobile 1000 tons of mobile
source source source source
--------------------------------------------------------------------------------------------------------------------------------------------------------
Total for engines subject to this final rule*................... 640 10.0 1,411 23.5 5,363 5.4 36.5 4.8
============
Highway Motorcycles............................................. 17 0.3 172 2.9 693 0.7 1.0 0.1
Nonroad Industrial SI £ 19 kW*........................ 553 8.6 371 6.2 2,703 2.7 2.7 0.4
Recreational SI*................................................ 15 0.2 1,038 17.3 2,649 2.7 31.9 4.2
Recreational Marine Diesel*..................................... 72 1.1 2 0.0 11 0.0 1.9 0.3
Marine SI Evap.................................................. 0 0.0 122 2.0 0 0.0 0 0.0
Marine SI Exhaust............................................... 64 1.0 269 4.5 2,083 2.1 29 3.8
Nonroad SI < 19 kW.............................................. 126 2.0 1,200 20.0 32,310 32.4 93 12.3
Nonroad Diesel.................................................. 1,994 31.0 158 2.6 1,727 1.7 306 40.4
Commercial Marine Diesel........................................ 1,166 18.1 52 0.9 198 0.2 74 9.8
Locomotive...................................................... 531 8.3 30 0.5 119 0.1 18 2.4
------------
Total Nonroad................................................... 4,521 70 3,242 54 41,800 42 557 74
Total Highway................................................... 1,648 26 2,496 42 56,303 56 158 21
Aircraft........................................................ 262 4 262 4 1,502 2 43 6
------------
Total Mobile Sources............................................ 6,431 100 6,000 100 99,605 100 758 100
============
Total Man-Made Sources.......................................... 16,639 -- 17,020 -- 123,983 -- 3,319 --
============
Mobile Source percent of Total Man-Made Sources................. 39 -- 35 -- 80 -- 23 --
--------------------------------------------------------------------------------------------------------------------------------------------------------
[[Page 68248]]
3. Why are Controls to Protect against CO Nonattainment and to Protect
Visibility Needed From the Nonroad Engines and Vehicles That Would Be
Subject to This Rule?
i. Why are We Controlling CO Emissions from Nonroad Engines and
Vehicles that Would be Subject to this Rule?
Engines subject to this rule contributed about 3.8 percent of CO
from mobile sources in 2000. Over 22.4 million people currently live in
the 13 nonattainment areas for the CO National Ambient Air Quality
Standard (NAAQS). Industry association comments questioned the need for
CO control and snowmobile contribution, in particular. First, the
statute envisions that categories should be considered in determining
contribution because otherwise, it would be possible to continue to
arbitrarily divide subcategories until the contribution from any
subcategory becomes minimal while the cumulative effect of the air
pollution remains. EPA previously determined that the category of Large
SI engines and recreational vehicles cause or contribute to ambient CO
and ozone in more than one nonattainment area (65 FR 76790, December 7,
2000). EPA also examined recreational vehicles separately and found
that recreational vehicles subject to this rule contribute to CO
nonattainment in areas such as Los Angeles, Phoenix, Anchorage, and Las
Vegas (see RSD chapter 2). Thus, if considered as a category,
recreational vehicles contribute to CO nonattainment.\6\ Moreover, when
we examined snowmobiles separately, they met the contribution criteria.
---------------------------------------------------------------------------
\6\ Likewise, Large SI equipment and recreational marine diesel
engines also contribute to CO in nonattainment areas.
---------------------------------------------------------------------------
The International Snowmobile Manufacturers Association (ISMA)
stated in its public comments that snowmobiles in particular are not
operated in many of the CO nonattainment areas because of lack of snow
(although they may be stored in those areas). The commenters also
contended that northern areas have experienced improved CO air quality.
Many areas are making progress in improving their air quality. However,
an area cannot be redesignated to attainment until it can show EPA that
it has had air quality levels within the level required for attainment
and that it has a plan in place to maintain such levels. Until areas
have been redesignated, they remain nonattainment areas.\7\ Snowmobiles
contribute to CO nonattainment in more than one of these areas.
---------------------------------------------------------------------------
\7\ There are important reasons to focus on redesignation
status, as compared to just current air quality. Areas with a few
years of attainment data can and often do have exceedances following
such years of attainment because of several factors including
different climatic events during the later years, increases in
inventories, etc. Control of emissions from nonroad engines can help
to avoid potential future air quality problems.
---------------------------------------------------------------------------
Snowmobiles have relatively high per-engine CO emissions, and they
can be a significant source of ambient CO levels in CO nonattainment
areas. Despite the fact that snowmobiles are largely banned in CO
nonattainment areas by the state of Alaska, the state estimated (and a
National Research Council study confirmed) that snowmobiles contributed
0.3 tons/day in 2001 to Fairbanks' CO nonattainment area or 1.2 percent
of a total inventory of 23.3 tons per day in 2001.\8,9\ While Fairbanks
has made significant progress in reducing ambient CO concentrations,
existing climate conditions make achieving and maintaining attainment
challenging. Anchorage, AK, reports a similar contribution of
snowmobiles to their emissions inventories (0.34 tons per day in 2000).
Furthermore, a recent National Academy of Sciences report concludes
that ``Fairbanks will be susceptible to violating the CO health
standards for many years because of its severe meteorological
conditions. That point is underscored by a December 2001 exceedance of
the standard in Anchorage which had no violations over the last 3
years.''\10\
---------------------------------------------------------------------------
\8\ Draft Anchorage Carbon Monoxide Emission Inventory and Year
2000 Attainment Projections, Air Quality Program, May 2001, Docket
Number A-2000-01, Document II-A-40; Draft Fairbanks 1995-2001 Carbon
Monoxide Emissions Inventory, June 1, 2001, Docket Number A-2000-01,
Document II-A-39.
\9\ National Research Council. The Ongoing Challenge of Managing
Carbon Monoxide Pollution in Fairbanks, AK. May 2002. Docket A-2000-
01, Document No. IV-A-115.
\10\ National Research Council. The Ongoing Challenge of
Managing Carbon Monoxide Pollution in Fairbanks, AK. May 2002.
Docket A-2000-01, Document IV-A-115.
---------------------------------------------------------------------------
ISMA commented that it agreed with EPA that there is a snowmobile
trail within the Spokane, WA, CO nonattainment area, although they
noted that snowmobile operation alone would not result in CO
nonattainment. However, emissions from regulated categories need only
contribute to, not themselves cause, nonattainment. Concentrations of
NAAQS-related pollutants are by definition a result of multiple sources
of pollution.
Several states that contain CO nonattainment areas also have large
populations of registered snowmobiles and nearby snowmobile trails in
adjoining counties, which are an indication of where they are operated
(see Table I.E-4). EPA requested comment on the volume and nature of
snowmobile use in these and other CO nonattainment areas. ISMA
commented on the proximity of trails to northern CO nonattainment
areas, assuming that snowmobiles are operated only on trails. A search
of the available literature indicates that snowmobiles are ridden in
areas other than trails. For example, a 1998 report by the Michigan
Department of Natural Resources indicates that from 1993 to 1997, of
the 146 snowmobile fatalities studied, 46 percent occurred on a state
or county roadway (another 2 percent on roadway shoulders) and 27
percent occurred on private lands. Furthermore, accident reports in CO
nonattainment area Fairbanks, AK, demonstrate that snowmobiles driven
on streets have collided with motor vehicles. On certain days there may
be concentrations of snowmobiles operated in nonattainment areas due to
public events such as snowmachine races (such as the Iron Dog Gold Rush
Classic, which finishes in Fairbanks, AK), during which snowmobiles
will be present and operated.
Table I.E-4.--Snowmobile Use in Selected CO Nonattainment Areas
----------------------------------------------------------------------------------------------------------------
2001 State
City and state CO nonattainment classification snowmobile
population\a\
----------------------------------------------------------------------------------------------------------------
Anchorage, AK
Fairbanks, AK................. Serious...................................................... \b\ 35576
Spokane, WA................... Serious...................................................... 31532
Fort Collins, CO.............. Moderate..................................................... 32500
Medford, OR................... Moderate..................................................... 16809
[[Page 68249]]
Missoula, MT.................. Moderate..................................................... 23440
----------------------------------------------------------------------------------------------------------------
\a\ Source: ISMA U.S. Snowmobile Registration History, May 15, 2001; various studies prepared for state
snowmobile associations included in Docket A-2000-01.
\b\ Point of sale registration was not mandatory in Alaska prior to 1998, so the statewide registered population
is likely to underestimate the total population.
Exceedances of the 8-hour CO standard were recorded in three of
seven CO nonattainment areas located in the northern portion of the
country over the five year period from 1994 to 1999: Fairbanks, AK;
Medford, OR; and Spokane, WA.\11\ Given the variability in CO ambient
concentrations due to weather patterns such as inversions, the absence
of recent exceedances for some of these nonattainment areas should not
be viewed as eliminating the need for further reductions to
consistently attain and maintain the standard. A review of CO monitor
data in Fairbanks from 1986 to 1995 shows that while median
concentrations have declined steadily, unusual combinations of weather
and emissions have resulted in elevated ambient CO concentrations well
above the 8-hour standard of 9 ppm. Specifically, a Fairbanks monitor
recorded average 8-hour ambient concentrations at 16 ppm in 1988,
around 9 ppm from 1990 to 1992, and then a steady increase in CO
ambient concentrations at 12, 14 and 16 ppm during some extreme cases
in 1993, 1994 and 1995, respectively.\12\
---------------------------------------------------------------------------
\11\ Technical Memorandum to Docket A-2000-01 from Drew Kodjak,
Attorney-Advisor, Office of Transportation and Air Quality, ``Air
Quality Information for Selected CO Nonattainment Areas,'' July 27,
2001, Docket Number A-2000-01, Document Number II-B-18.
\12\ Air Quality Criteria for Carbon Monoxide, U.S. EPA, EPA
600/P-99/001F, June 2000, at 3-38, Figure 3-32 (Federal Bldg, AIRS
Site 020900002). Air Docket A-2000-01, Document Number II-A-29. This
document is also available at http://www.epa.gov/ncea/
coabstract.htm.
---------------------------------------------------------------------------
In addition, there are 6 areas that have not been classified as
nonattainment where air quality monitoring indicated a need for CO
control. For example, CO monitors in northern locations such as Des
Moines, IA, and Weirton, WV/Steubenville, OH, registered levels above
the level of the CO standards in 1998.
ii. Why are Controls Needed From the Nonroad Engines and Vehicles
That Would Be Subject to this Rule to Protect Visibility?
(1) Visibility is Impaired by Fine PM and Precursor Emissions From
Nonroad Engines and Vehicles That Would Be Subject to This Rule.
Visibility can be defined as the degree to which the atmosphere is
transparent to visible light.\13\ Visibility degradation is an easily
noticeable effect of fine PM present in the atmosphere, and fine PM is
the major cause of reduced visibility in parts of the United States,
including many of our national parks and in places across the country
where people live, work, and recreate. Fine particles with significant
light-extinction efficiencies include organic matter, sulfates,
nitrates, elemental carbon (soot), and soil.
---------------------------------------------------------------------------
\13\ National Research Council, 1993. Protecting Visibility in
National Parks and Wilderness Areas. National Academy of Sciences
Committee on Haze in National Parks and Wilderness Areas. National
Academy Press, Washington, DC. This document is available on the
internet at http://www.nap.edu/books/0309048443/html/. See also U.S.
EPA Air Quality Criteria Document for Particulate Matter (1996) and
Review of the National Ambient Air Quality Standards for Particulate
Matter: Policy Assessment of Scientific and Technical Information.
These documents can be found in Docket A-99-06, Documents No. II-A-
23 and IV-A-130-32.
---------------------------------------------------------------------------
Visibility is an important effect because it has direct
significance to people's enjoyment of daily activities in all parts of
the country. Individuals value good visibility for the well-being it
provides them directly, both in where they live and work, and in places
where they enjoy recreational opportunities. Visibility is highly
valued in significant natural areas such as national parks and
wilderness areas, because of the special emphasis given to protecting
these lands now and for future generations.
To quantify changes in visibility, we compute a light-extinction
coefficient, which shows the total fraction of light that is decreased
per unit distance. Visibility can be described in terms of PM
concentrations, visual range, light extinction or deciview.\14\ In
addition to limiting the distance that one can see, the scattering and
absorption of light caused by air pollution can also degrade the color,
clarity, and contrast of scenes.
---------------------------------------------------------------------------
\14\ Visual range can be defined as the maximum distance at
which one can identify a black object against the horizon sky. It is
typically described in miles or kilometers. Light extinction is the
sum of light scattering and absorption by particles and gases in the
atmosphere. It is typically expressed in terms of inverse megameters
(Mm-1), with larger values representing worse visibility. The
deciview metric describes perceived visual changes in a linear
fashion over its entire range, analogous to the decibel scale for
sound. A deciview of 0 represents pristine conditions. Under many
scenic conditions, a change of 1 deciview is considered perceptible
by the average person.
---------------------------------------------------------------------------
Visibility effects are manifest in two main ways: as local
impairment (for example, localized hazes and plumes) and as regional
haze. In addition, visibility impairment has a time dimension in that
it might relate to a short-term excursion or to longer periods (for
example, worst 20 percent of days or annual average levels).
Local-scale visibility degradation is commonly seen as a plume
resulting from the emissions of a specific source or small group of
sources, or it is in the form of a localized haze such as an urban
``brown cloud.'' Plumes are comprised of smoke, dust, or colored gas
that obscure the sky or horizon relatively near sources. Impairment
caused by a specific source or small group of sources has been
generally termed as ``reasonably attributable.''
The second type of impairment, regional haze, results from
pollutant emissions from a multitude of sources located across a broad
geographic region. It impairs visibility in every direction over a
large area, in some cases over multi-state regions. Regional haze masks
objects on the horizon and reduces the contrast of nearby objects. The
formation, extent, and intensity of regional haze is a function of
meteorological and chemical processes, which sometimes cause fine
particulate loadings to remain suspended in the atmosphere for several
days and to be transported hundreds of kilometers from their sources.
On an annual average basis, the concentrations of non-anthropogenic
fine PM are generally small when compared with concentrations of fine
particles from anthropogenic sources. Anthropogenic contributions
account for about one-third of the average extinction coefficient in
the rural West and more than 80 percent in the rural East. Because of
significant differences related to visibility conditions in the eastern
and western U.S., we present information about visibility by region.
Furthermore, it is important to note that even in those areas with
relatively low
[[Page 68250]]
concentrations of anthropogenic fine particles, such as the Colorado
plateau, small increases in anthropogenic fine particle concentrations
can lead to significant decreases in visual range. This is one of the
reasons Class I areas have been given special consideration under the
Clean Air Act.
Nonroad engines that are subject to this final rule contribute to
ambient fine PM levels in two ways. First, they contribute through
direct emissions of fine PM. As shown in Table I.E-1, these engines
emitted 14,600 tons of PM (over 2 percent of all mobile source PM) in
2000. Second, these engines contribute to indirect formation of PM
through their emissions of gaseous precursors which are then
transformed in the atmosphere into particles. For example, these
engines emitted over 8 percent of the HC tons from mobile sources.
Furthermore, recreational vehicles, such as snowmobiles and all-terrain
vehicles emit high levels of organic carbon (as HC) on a per-engine
basis. Some organic emissions are transformed into particles in the
atmosphere and other volatile organics can condense if emitted in cold
temperatures, as is the case for emissions from snowmobiles, for
example. Organic carbon accounts for between 27 and 36 percent of
ambient fine particle mass depending on the area of the country.
(A) Visibility Impairment Where People Live, Work and Recreate
The secondary PM NAAQS is designed to protect against adverse
welfare effects such as visibility impairment. In 1997, the secondary
PM NAAQS was set as equal to the primary (health-based) PM NAAQS (62
Federal Register No. 138, July 18, 1997). EPA concluded that PM can and
does produce adverse effects on visibility in various locations,
depending on PM concentrations and factors such as chemical composition
and average relative humidity. In 1997, EPA demonstrated that
visibility impairment is an important effect on public welfare and that
visibility impairment is experienced throughout the U.S., in multi-
state regions, urban areas, and remote Federal Class I areas.
In many cities having annual mean PM2.5 concentrations
exceeding 17 [mu]g/m\3\, improvements in annual average visibility
resulting from the attainment of the annual PM2.5 standard
are expected to be perceptible to the general population (e.g., to
exceed 1 deciview). Based on annual mean monitored PM2.5
data, many cities in the Northeast, Midwest, and Southeast as well as
Los Angeles would be expected to experience perceptible improvements in
visibility if the PM2.5 annual standard were attained. For
example, in Washington, DC, where the IMPROVE monitoring network shows
annual mean PM2.5 concentrations at about 19 [mu]g/m\3\
during the period of 1992 to 1995, approximate annual average
visibility would be expected to improve from 21 km (29 deciview) to 27
km (27 deciview), a change of 2 deciviews. The PM2.5 annual
average in Washington, DC, was 18.9 [mu]g/m\3\ in 2000.
The updated monitored data and air quality modeling presented in
the RSD confirm that the visibility situation identified during the
NAAQS review in 1997 is still likely to exist. Thus, the determination
in the NAAQS rulemaking about broad visibility impairment and related
benefits from NAAQS compliance are still relevant. Levels above the
fine PM NAAQS cause adverse welfare impacts, such as visibility
impairment (both regional and localized impairment).
Furthermore, in setting the PM NAAQS, EPA acknowledged that levels
of fine particles below the NAAQS may also contribute to unacceptable
visibility impairment and regional haze problems in some areas, and
Clean Air Act Section 169 provides additional authorities to remedy
existing impairment and prevent future impairment in the 156 national
parks, forests and wilderness areas labeled as Class I areas.
In making determinations about the level of protection afforded by
the secondary PM NAAQS, EPA considered how the Section 169 regional
haze program and the secondary NAAQS would function together. Regional
strategies are expected to improve visibility in many urban and non-
Class I areas as well. The following recommendation for the National
Research Council, Protecting Visibility in National Parks and
Wilderness Areas (1993), addresses this point:
Efforts to improve visibility in Class I areas also would benefit
visibility outside these areas. Because most visibility impairment is
regional in scale, the same haze that degrades visibility within or
looking out from a national park also degrade visibility outside it.
The 1999-2000 PM2.5 monitored values, which cover about
a third of the nation's counties, indicate that at least 82 million
people live in areas where long-term ambient fine particulate matter
levels are at or above 15 [mu]g/m\3\.\15\ Thus, these populations (plus
those who travel to those areas) could be experiencing visibility
impairment that is unacceptable, and emissions of PM and its precursors
from engines in these categories contribute to this unacceptable
impairment.\16\
---------------------------------------------------------------------------
\15\ Memorandum to Docket A-99-06 from Eric O. Ginsburg, Senior
Program Advisor, ``Summary of 1999 Ambient Concentrations of Fine
Particulate Matter,'' November 15, 2000. Air Docket A-2000-01,
Document No. II-B-12.
\16\ These populations would obviously also be exposed to PM
concentrations associated with the adverse health impacts related to
PM2.5.
---------------------------------------------------------------------------
Because the chemical composition of the PM affects visibility
impairment, we used EPA's Regulatory Model System for Aerosols and
Deposition (REMSAD)\17\ model to project visibility conditions in 2030
accounting for the chemical composition of the particles and to
estimate visibility impairment directly as changes in deciview. Our
projections included anticipated emissions from the engines subject to
this rule, and although our emission predictions reflected our best
estimates of emissions projections at the time the modeling was
conducted, we now have new estimates, as discussed in the RSD Chapter
1. Based on public comment for this rule and new information, we have
revised our emissions estimates in some categories downwards and other
categories upwards; however, on net, we believe the modeling
underestimates the PM air quality levels that would have been predicted
if new inventories were used.
---------------------------------------------------------------------------
\17\ Additional information about the Regulatory Model System
for Aerosols and Deposition (REMSAD) and our modeling protocols can
be found in our Regulatory Impact Analysis: Heavy-Duty Engine and
Vehicle Standards and Highway Diesel Fuel Sulfur Control
Requirements, document EPA420-R-00-026, December 2000. Docket No. A-
2000-01, Document No. A-II-13. This document is also available at
http://www.epa.gov/otaq/disel.htm#documents.
---------------------------------------------------------------------------
The most reliable information about the future visibility levels
would be in areas for which monitoring data are available to evaluate
model performance for a base year (e.g., 1996). Accordingly, we
predicted that in 2030, 49 percent of the population will be living in
areas where fine PM levels are above 15 [mu]g/m\3\ and monitors are
available.\18\ This can be compared with the 1996 level of 37 percent
of the population living in areas where fine PM levels are above 15
[mu]g/m\3\ and monitors are available. Thus, a substantial percent of
the population would experience unacceptable visibility impairment in
areas where they live, work and recreate.
---------------------------------------------------------------------------
\18\ Technical Memorandum, EPA Air Docket A-99-06, Eric O.
Ginsburg, Senior Program Advisor, Emissions Monitoring and Analysis
Division, OAQPS, Summary of Absolute Modeled and Model-Adjusted
Estimates of Fine Particulate Matter for Selected Years, December 6,
2000, Table P-2. Docket Number 2000-01, Document Number II-B-14.
---------------------------------------------------------------------------
As shown in Table I.E-5, in 2030, we expect visibility in the East
to be about
[[Page 68251]]
19 deciviews (or visual range of 60 kilometers) on average, with poorer
visibility in urban areas, compared to the visibility conditions
without man-made pollution of 9.5 deciviews (or visual range of 150
kilometers). Likewise, we expect visibility in the West to be about 9.5
deciviews (or visual range of 150 kilometers) in 2030, compared to the
visibility conditions without man-made pollution of 5.3 deciviews (or
visual range of 230 kilometers).
Nonroad engines contribute significantly to these effects. As shown
in Tables I.E-1 through I.E-3, nonroad engines emissions contribute a
large portion of the total PM emissions from mobile sources and
anthropogenic sources, in general. These emissions occur in and around
areas with PM levels above the annual PM2.5 NAAQS. The
engines subject to the final rule will contribute to these effects.
They are estimated to emit 36,500 tons of direct PM in 2030, which is
1.1 percent of the total anthropogenic PM emissions in 2030. Similarly,
for PM precursors, the engines subject to this rule will emit 640,000
tons of NOX and 1,411,000 tons HC in 2030, which are 3.8 and
8.3 percent of the total anthropogenic NOX and HC emissions,
respectively, in 2030. Recreational vehicles in particular contribute
to these levels. In Table I.E-1 through I.E-3, we show that
recreational vehicles emitted about 1.7 percent of mobile source PM
emissions in 2000. Similarly, recreational vehicles are modeled to emit
over 4 percent of mobile source PM in 2020 and 2030. Thus, the
emissions from these sources contribute to the visibility impairment
modeled for 2030 summarized in the table.
Furthermore, for 20 counties across nine states, snowmobile trails
are found within or near counties that registered ambient
PM2.5 concentrations at or above 15 [mu]g/m\3\, the level of
the PM2.5 NAAQS.\19\ Fine particles may remain suspended for
days or weeks and travel hundreds to thousands of kilometers, and thus
fine particles emitted or created in one county may contribute to
ambient concentrations in a neighboring county.20, 21
---------------------------------------------------------------------------
\19\ Memo to file from Terence Fitz-Simons, OAQPS, Scott
Mathias, OAQPS, Mike Rizzo, Region 5, ``Analyses of 1999 PM Data for
the PM NAAQS Review,'' November 17, 2000, with attachment B, 1999
PM2.5 Annual Mean and 98th Percentile 24-Hour Average
Concentrations. Docket No. A-2000-01, Document No. II-B-17.
\20\ This information also shows that snowmobiles contribute to
concentrations of fine PM that are above the primary health-related
NAAQS, which indicates that emissions from snowmobiles also
contribute to primary and secondary PM pollution that may reasonably
be anticipated to endanger public health and welfare.
\21\ Review of the National Ambient Air Quality Standards for
Particulate Matter: Policy Assessment for Scientific and Technical
Information, OAQPS Staff Paper, EPA-452[bs]R-96-
013, July, 1996, at IV-7. This document is available from Docket A-
99-06, Document II-A-23.
Table I.E-5--Summary of 2030 National Visibility Conditions Based on
REMSAD Modeling
[Deciviews]
------------------------------------------------------------------------
Predicted 2030
visibility b Natural
Regions a (annual background
average) visibility
------------------------------------------------------------------------
Eastern U.S............................. 18.98 9.5
Urban............................... 20.48
Rural............................... 18.38
Western U.S............................. 9.54 5.3
Urban............................... 10.21
Rural............................... 9.39
------------------------------------------------------------------------
a Eastern and Western Regions are separated by 100 degrees north
longitude. Background visibility conditions differ by region.
b The results incorporate earlier emissions estimates from the engines
subject to this rule, as discussed in the Final Regulatory Support
Document. We have revised our estimates both upwards for some
categories and downwards for others based on public comment and
updated information; however, we believe that the net results would
underestimate future PM emissions.
(B) Visibility Impairment in Class I Areas
The Clean Air Act establishes special goals for improving
visibility in many national parks, wilderness areas, and international
parks. In the 1977 amendments to the Clean Air Act, Congress set as a
national goal for visibility the ``prevention of any future, and the
remedying of any existing, impairment of visibility in mandatory class
I Federal areas which impairment results from manmade air pollution''
(CAA section 169A(a)(1)). The Amendments called for EPA to issue
regulations requiring States to develop implementation plans that
assure ``reasonable progress'' toward meeting the national goal (CAA
Section 169A(a)(4)). EPA issued regulations in 1980 to address
visibility problems that are ``reasonably attributable'' to a single
source or small group of sources, but deferred action on regulations
related to regional haze, a type of visibility impairment that is
caused by the emission of air pollutants by numerous emission sources
located across a broad geographic region. At that time, EPA
acknowledged that the regulations were only the first phase for
addressing visibility impairment. Regulations dealing with regional
haze were deferred until improved techniques were developed for
monitoring, for air quality modeling, and for understanding the
specific pollutants contributing to regional haze.
In the 1990 Clean Air Act amendments, Congress provided additional
emphasis on regional haze issues (see CAA section 169B). In 1999 EPA
finalized a rule that calls for States to establish goals and emission
reduction strategies for improving visibility in all 156 mandatory
Class I national parks and wilderness areas. In this rule, EPA
established a ``natural visibility'' goal. In that rule, EPA also
encouraged the States to work together in developing and implementing
their air quality plans. The regional haze program is focused on long-
term emissions decreases from the entire regional emissions inventory
comprised of major and minor stationary sources, area sources and
mobile sources. The regional haze program is designed to improve
visibility and air quality in our most treasured natural areas from
these broad sources. At the same time, control strategies designed to
improve visibility in the national parks and wilderness areas will
improve visibility over broad geographic areas. In the 1997 PM NAAQS
rulemaking, EPA also anticipated the need in addition to the NAAQS and
Section 169 regional haze program to continue to address localized
impairment that may relate to unique circumstances in some Western
areas. For mobile sources, there is a need for a Federal role in
reduction of those emissions, particularly because mobile source
vehicles are regulated primarily at the federal level.
Visibility impairment is caused by pollutants (mostly fine
particles and precursor gases) directly emitted to the atmosphere by
several activities (such as electric power generation, various industry
and manufacturing processes, truck and auto emissions, construction
activities, etc.). These gases and particles scatter and absorb light,
removing it from the sight path and creating a hazy condition.
Visibility impairment is caused by both regional haze and localized
impairment. As described above, regional haze is caused
[[Page 68252]]
by the emission from numerous sources located over a wide geographic
area.\22\
---------------------------------------------------------------------------
\22\ U.S. EPA Review of the National Ambient Air Quality
Standards for Particulate Matter: Policy Assessment of Scientific
and Technical Information OAQPS Staff Paper. EPA-452/R-96-013. 1996.
Docket Number A-99-06, Documents Nos. II-A-18, 19, 20, and 23. The
particulate matter air quality criteria documents are also available
at http://www.epa.gov/ncea/partmatt.htm.
---------------------------------------------------------------------------
Because of evidence that fine particles are frequently transported
hundreds of miles, all 50 states, including those that do not have
Class I areas, participate in planning, analysis, and, in many cases,
emission control programs under the regional haze regulations. Even
though a given State may not have any Class I areas, pollution that
occurs in that State may contribute to impairment in Class I areas
elsewhere. The rule encourages states to work together to determine
whether or how much emissions from sources in a given state affect
visibility in a downwind Class I area.
The regional haze program calls for states to establish goals for
improving visibility in national parks and wilderness areas to improve
visibility on the haziest 20 percent of days and to ensure that no
degradation occurs on the clearest 20 percent of days (64 FR 35722.
July 1, 1999). The rule requires states to develop long-term strategies
including enforceable measures designed to meet reasonable progress
goals toward natural visibility conditions. Under the regional haze
program, States can take credit for improvements in air quality
achieved as a result of other Clean Air Act programs, including
national mobile source programs.\23\
---------------------------------------------------------------------------
\23\ In a recent case, American Corn Growers Association v. EPA,
291 F. 3d 1 (D.C. Cir 2002), the court vacated the BART provisions
of the Regional Haze rule, but the court denied industry's challenge
to EPA's requirement that state's SIPs provide for reasonable
progress towards achieving natural visibility conditions in national
parks and wilderness areas and the ``no degradation'' requirement.
Industry did not challenge requirements to improve visibility on the
haziest 20 percent of days. A copy of this decision can be found in
Docket A-2000-01, Document IV-A-113.
---------------------------------------------------------------------------
In the PM air quality modeling described above, we also modeled
visibility conditions in the Class I areas, and we summarize the
results by region in Table I.E-6.
Table I.E-6--Summary of 2030 Visibility Conditions in Class I Areas
Based on REMSAD Modeling
[Annual Average Deciview]
------------------------------------------------------------------------
Natural
Region a Predicted 2030 background
visibility b visibility
------------------------------------------------------------------------
Eastern .............. 9.5
Southeast............................... 25.02 ..............
Northeast/Midwest....................... 21.00 ..............
Western .............. 5.3
Southwest............................... 8.69 ..............
California.............................. 11.61 ..............
Rocky Mountain.......................... 12.30 ..............
Northwest............................... 15.44 ..............
-----------------
National Class I Area Average....... 14.04 ..............
------------------------------------------------------------------------
a Regions are depicted in Figure VI-5 in the Regulatory Support Document
for the highway Heavy Duty Engine/Diesel Fuel RIA (EPA 420-R-00-026,
December 2000.) Background visibility conditions differ by region:
Eastern natural background is 9.5 deciviews (or visual range of 150
kilometers) and in the West natural background is 5.3 deciviews (or
visual range of 230 kilometers).
b The results incorporate earlier emissions estimates from the engines
subject to this rule, as discussed in the Final Regulatory Support
Document. We have revised our estimates both upwards for some
categories and downwards for others based on public comment and
updated information; however, we believe that the net results
underestimate future PM emissions.
Nonroad engines represent a sizeable portion of the total inventory
of anthropogenic emissions related to PM2.5, as shown in the tables
above. Numerous types of nonroad engines may operate near Class I areas
(e.g., mining equipment, recreational vehicles, and agricultural
equipment). We have reviewed contributions from snowmobile in
particular.
Emissions from nonroad engines, in particular snowmobiles,
contribute significantly to visibility impairment in Class I areas.\24\
Visibility and PM monitoring data are available for eight Class I areas
where snowmobiles are commonly used. These are: Acadia, Boundary
Waters, Denali, Mount Rainier, Rocky Mountain, Sequoia and Kings
Canyon, Voyageurs, and Yellowstone.\25\ Fine particle monitoring data
for these parks are set out in Table I.E-7. This table shows the number
of monitored days in the winter that fell within the 20-percent worst
visibility days for each of these eight parks. Monitors collect data 2
days a week for a total of about 104 days of monitored values. Thus,
for a particular site, a maximum of 21 worst possible days of these 104
days with monitored values constitute the set of 20-percent worst
visibility days during a year which are tracked as the primary focus of
regulatory efforts.\26\ With the exception of Denali in Alaska, we
defined the snowmobile season as January 1 through March 15 and
December 15 through December 31 of the same calendar year, consistent
with the methodology used in the Regional Haze Rule, which is calendar-
year based. For Denali in Alaska, the snowmobile season is October 1 to
April 30.
---------------------------------------------------------------------------
\24\ The results incorporate earlier emissions estimates from
the engines subject to this rule, as discussed in the Final
Regulatory Support Document. We have revised our estimates both
upwards for some categories and downwards for others based on public
comment and updated information; however, we believe that the net
results would underestimate future PM emissions.
\25\ No data were available at five additional parks where
snowmobiles are also commonly used: Black Canyon of the Gunnison,
CO, Grand Teton, WY, Northern Cascades, WA, Theodore Roosevelt, ND,
and Zion, UT.
\26\ Letter from Debra C. Miller, Data Analyst, National Park
Service, to Drew Kodjak, August 22, 2001. Docket No. A-2000-01,
Document Number II-B-28.
[[Page 68253]]
Table I.E-7--Winter Days That Fall Within the 20 Percent Worst Visibility Days At National Parks Used by
Snowmobiles
----------------------------------------------------------------------------------------------------------------
Number of sampled wintertime days within 20
percent worst visibility days (maximum of 21
NPS unit States out of 104 monitored days)
-----------------------------------------------
1996 1997 1998 1999
----------------------------------------------------------------------------------------------------------------
Acadia NP............................. ME...................... 4 4 2 1
Denali NP and Preserve................ AK...................... 10 10 12 9
Mount Rainier NP...................... WA...................... 1 3 1 1
Rocky Mountain NP..................... CO...................... 2 1 2 1
Sequoia and Kings Canyon NP........... CA...................... 4 9 1 8
-------------
Voyageurs NP (1989-1992).............. MN...................... 1989 1990 1991 1992
3 4 6 8
--Boundary Waters USFS Wilderness Area MN...................... 2 5 1 5
(close to Voyaguers with recent data).
Yellowstone NP........................ ID, MT, WY.............. 0 2 0 0
----------------------------------------------------------------------------------------------------------------
Source: Letter from Debra C. Miller, Data Analyst, National Park Service, to Drew Kodjak, August 22, 2001.
Docket No. A-2000-01, Document Number II-B-28.
According to the National Park Service, ``[s]ignificant differences
in haziness occur at all eight sites between the averages of the
clearest and haziest days. Differences in mean standard visual range on
the clearest and haziest days fall in the approximate range of 115-170
km.'' \27\ We examined future air quality predictions to whether the
emissions from recreational vehicles, such as snowmobiles, contribute
to regional visibility impairment in Class I areas. We present results
from the future air quality modeling described above for these Class I
areas in addition to inventory and air quality measurements.
Specifically, in Table I.E-8, we summarize the expected future
visibility conditions in these areas without these regulations.
---------------------------------------------------------------------------
\27\ Letter from Debra C. Miller, Data Analyst, National Park
Service, to Drew Kodjak, August 22, 2001. Docket No. A-2000-01,
Document Number II-B-28.
Table I.E-8--Estimated 2030 Visibility in Selected Class I Areas a,b
----------------------------------------------------------------------------------------------------------------
Natural
Predicted 2030 background
visibility visibility
Class I area County State (annual (annual
average average
deciview) deciview)
----------------------------------------------------------------------------------------------------------------
Eastern areas ..................... ..................... .............. 9.5
Acadia............................ Hancock Co........... ME................... 23.42 ..............
Boundary Waters................... St. Louis Co......... MN................... 22.07 ..............
Voyageurs......................... St. Louis Co......... MN................... 22.07 ..............
Western areas ..................... ..................... .............. 5.3
Grand Teton NP.................... Teton Co............. WY................... 11.97 ..............
Kings Canyon...................... Fresno Co............ CA................... 10.39 ..............
Mount Rainier..................... Lewis Co............. WA................... 16.19 ..............
Rocky Mountain.................... Larimer Co........... CO................... 8.11 ..............
Sequoia-Kings..................... Tulare Co............ CA................... 9.36 ..............
Yellowstone....................... Teton Co............. WY................... 11.97 ..............
----------------------------------------------------------------------------------------------------------------
a Natural background visibility conditions differ by region because of differences in factors such as relative
humidity: Eastern natural background is 9.5 deciviews (or visual range of 150 kilometers) and in the West
natural background is 5.3 deciviews (or visual range of 230 kilometers).
b The results incorporate earlier emissions estimates from the engines subject to this rule. We have revised our
estimates both upwards for some categories and downwards for others based on public comment and updated
information; however, on net, we believe that HD07 analyses would underestimate future PM emissions from these
categories.
The information presented in Table I.E-7 shows that visibility data
support a conclusion that there are at least 8 Class I Areas (7
national parks and one wilderness area) frequented by snowmobiles with
one or more wintertime days within the 20-percent worst visibility days
of the year, and in many cases several days. For example, Rocky
Mountain National Park in Colorado was frequented by about 27,000
snowmobiles during the 1998-1999 winter. Of the monitored days
characterized as within the 20-percent worst visibility monitored days,
2 of those days occurred during the wintertime when snowmobile
emissions such as hydrocarbons contributed to visibility impairment.
The information in Table I.E-8 shows that these areas also are
predicted to have high annual average deciview levels in the future.
Emissions from snowmobiles and other recreational vehicles, as well as
other nonroad engines contributed to these levels.\28\
---------------------------------------------------------------------------
\28\ See Chapter 1 in the RSD for a discussion or U.S. EPA
Technical Support Document for Heavy-duty Engine and Vehicle
Standards and Highway Diesel Fuel Sulfur Control Requirements--Air
Quality Modeling Analyses December 2000. Docket No. A-2000-01,
Docket Number IV-A-218. This document is also avaiable at
www.epa.gov/otaq/hdmodels.htm.
---------------------------------------------------------------------------
[[Page 68254]]
Ambient concentrations of fine particles are the primary pollutant
responsible for visibility impairment. The classes of fine particles
principally responsible for visibility impairment are sulfates,
nitrates, organic carbon particles, elemental carbon, and crustal
material. Hydrocarbon emissions from automobiles, trucks, snowmobiles,
and other industrial processes are common sources of organic carbon.
The organic carbon fraction of fine particles ranges from 47 percent in
Western areas such as Denali National Park, to 28 percent in Rocky
Mountain National Park, to 13 percent in Acadia National Park.\29\
---------------------------------------------------------------------------
\29\ Letter from Debra C. Miller, Data Analyst, National Park
Service, to Drew Kodjak, August 22, 2001. Docket No. A-2000-01,
Document Number II-B-28.
---------------------------------------------------------------------------
In the winter months, HC emissions from snowmobiles can be
significant, and these HC emissions can be more than half of the
organic carbon fraction of fine particles which are largely responsible
for visibility impairment. In Yellowstone, a park with high snowmobile
usage during the winter months, snowmobile HC emissions can exceed 500
tons per year, as much as several large stationary sources.\30\ Other
parks with less snowmobile traffic are also impacted although to a
lesser extent by these HC emissions.\31\
---------------------------------------------------------------------------
\30\ Emissions of NOX from snowmobiles contribute to
the total amount of particulate nitrate, although the total
NOX emissions from snowmobiles are considerably less than
HC or direct PM emissions from these engines.
\31\ Technical Memorandum, Aaron Worstell, Environmental
Engineer, National Park Service, Air Resources Division, Denver,
Colorado, particularly Table 1. Docket No. A-2000-01, Document
Number II-G-178.
---------------------------------------------------------------------------
Table I.E-9 shows estimated tons of four pollutants during the
winter season in five Class I national parks for which we have
estimates of snowmobile use. The national park areas outside of Denali
in Alaska are open to snowmobile operation in accordance with special
regulations (36 CFR part 7). Denali National Park permits snowmobile
operation by local rural residents engaged in subsistence uses (36 CFR
part 13).
Table I.E-9.--Winter Season Snowmobile Emissions
[tons; 1999 Winter Season]
------------------------------------------------------------------------
NPS unit HC CO NOX PM
------------------------------------------------------------------------
Denali NP & Preserve............ X standard for snowmobiles. This
standard will essentially cap NOX emissions from these
engines to prevent backsliding. We are not promulgating standards that
would require substantial reductions in NOX because we
believe that standards which force substantial NOX
reductions would likely not lead to reductions in PM and may in fact
increase PM levels. NOX emissions from snowmobiles are very
small, particularly compared to levels of HC. In fact, technologies
that reduce HC and CO are likely to increase levels of NOX
and vice versa, because technologies to reduce HC and CO emissions
would result in leaner operation. A lean air and fuel mixture causes
NOX emissions to increase. These increases are minor,
however, compared to the reductions of HC (and therefore PM) that
result from these techniques.
On the other hand, substantial control of NOX emissions
may have the counter-effect of increasing HC emissions and the greater
PM emissions associated with those HC emissions. The only way to reduce
NOX emissions from four-stroke engines (at the same time as
reducing HC and CO levels) would be to use a three-way catalytic
converter. We do not have enough information at this time on the
durability or safety implications of using a three-way catalyst with a
four-stroke engine in snowmobile applications. Three-way catalyst
technology is well beyond the technology reviewed for this rule and
would need substantial additional review before being contemplated for
snowmobiles. Thus, given the overwhelming level of HC compared to
NOX, and the secondary PM expected to result from these
levels, it would be premature and possibly counterproductive to
promulgate NOX standards that require significant
NOX reductions from snowmobiles at this time. We have
therefore decided to structure our long term HC+NOX standard
for 2012 and later model year snowmobiles to require only a cap on
NOX emissions from the advanced technology engines which
will be the dominant technology in the new snowmobiles certified at
that time.
II. Nonroad: General Provisions
This section describes general provisions concerning the emission
standards adopted in this final rule and the ways in which a
manufacturer shows compliance with these standards. Clean Air Act
section 213(a)(3) requires us to set standards that achieve the
greatest degree of emission reduction achievable through the
application of technology that will be available, giving appropriate
consideration to cost, noise, energy, and safety factors. Section
202(a)(4) provides further authority to adopt standards for pollution
beyond that regulated under section 202(a)(3). In addition to emission
standards, this document describes a variety of other provisions
necessary for implementing the proposed emission-control program in an
effective way, such as applying for certification, labeling engines,
and meeting warranty requirements.
The discussions in this section are general and are meant to cover
all the nonroad engines and vehicles subject to the new standards. In
this Section II, the term engine is sometimes used to include both
nonroad engines and nonroad vehicles. Refer to the discussions of
specific programs, contained in Sections III through VI, to determine
whether the regulations are being applied to the entire vehicle or just
the engine, as well as for more information about specific requirements
for different categories of nonroad engines and vehicles.
This section describes general nonroad provisions related to
certification prior to sale or introduction into commerce. Section VII
describes several compliance provisions that apply generally to nonroad
engines, and Section VIII similarly describes general testing
provisions.
A. Scope of Application
This final rule covers recreational marine diesel engines, nonroad
spark-ignition engines rated over 19 kW, and recreational spark-
ignition vehicles introduced into commerce in the United States. The
following sections describe generally when emission standards apply to
these products. These provisions are generally consistent with prior
nonroad and motor-vehicle rulemakings. Refer to the specific program
discussion below for more information about the scope of application
and timing of new standards.
1. What Engines and Vehicles Are Subject to the Standards?
The scope of this rule is broadly set by Clean Air Act section
213(a), which instructs us to set emission standards for new nonroad
engines and new nonroad vehicles. Generally speaking, this rule is
intended to cover all new engines and vehicles in the categories listed
above (including any associated equipment or vessels) for their entire
useful lives, as defined in the regulations.\33\ Once the emission
standards apply to a group of engines or vehicles, manufacturers of a
new engine must have an approved certificate of conformity from us
before selling them in the United States.\34\ This also applies to
importation by any person and any other means of introducing new
engines and vehicles into commerce. We also require equipment
manufacturers that install engines from other companies to install only
certified engines into new equipment once emission standards
[[Page 68256]]
apply. The information we require of manufacturers applying for
certification (with the corresponding engine labels) provides assurance
that manufacturers have met their obligation to make engines that meet
emission standards over the useful life we specify in the regulations.
---------------------------------------------------------------------------
\33\ For recreational vehicles, we are adopting vehicle-based
standards. For these applications, the term ``engine'' in this
document applies equally to the vehicles.
\34\ The term ``manufacturer'' includes any individual or
company that manufactures any new engine for sale or otherwise
introduces a new engine into commerce in the United States. It also
includes importers for resale.
---------------------------------------------------------------------------
2. How Do I Know if My Engine or Equipment Is New?
We are defining ``new'' consistent with previous rulemakings. We
will consider a nonroad engine (or nonroad equipment) to be new until
its title has been transferred to the ultimate purchaser or the engine
has been placed into service. This definition applies to both engines
and equipment, so the nonroad equipment using these engines, including
all-terrain vehicles, snowmobiles, off-highway motorcycles, and other
land-based nonroad equipment will be considered new until their title
has been transferred to an ultimate buyer. In Section II.B.1 we
describe how to determine the model year of individual engines and
vehicles.
To further clarify the definition of new nonroad engine, we specify
that a nonroad engine, vehicle, or equipment is placed into service
when it is used for its intended purpose. An engine subject to emission
standards is used for its functional purpose when it is installed in an
all-terrain vehicle, snowmobile, off-highway motorcycle, marine vessel,
or other piece of nonroad equipment. We need to make this clarification
because some engines are made by modifying a highway or land-based
nonroad engine that has already been installed on a vehicle or other
piece of equipment. For example, someone can install an engine in a
recreational marine vessel after it has been used for its functional
purpose as a land-based highway or nonroad engine. We believe our
approach is reasonable because the practice of adapting used highway or
land-based nonroad engines may become more common if these engines are
not subject to emission standards.
In summary, an engine may be subject to emission standards if it
is:
. Freshly manufactured, whether domestic or imported; this
may include engines produced from engine block cores
. Installed for the first time in nonroad equipment after
having powered an automobile or a category of nonroad equipment subject
to different emission standards
. Installed in new nonroad equipment, regardless of the age
of the engine
. Imported (freshly manufactured or used) and was originally
manufactured after the effective date of our standards
3. When Do Imported Engines Need To Meet Emission Standards?
The emission standards apply to all new engines sold in the United
States. Consistent with Clean Air Act section 216, engines that are
imported by any person, whether freshly manufactured or used are
considered ``new'' engines.\35\ Thus, we include engines that are
imported for use in the United States, whether they are imported as
loose engines or if they are already installed on a marine vessel,
recreational vehicle, or other piece of nonroad equipment, built
elsewhere. All imported engines manufactured after our standards begin
to apply need an EPA-issued certificate of conformity to clear customs,
with limited exemptions (as described below).
---------------------------------------------------------------------------
\35\ The definition in Clean Air Act section 216 applies
specifically to ``new motor vehicles,'' but we have interpreted
``new nonroad engine'' consistently with the definition in section
216.
---------------------------------------------------------------------------
An engine or marine vessel, recreational vehicle, or other piece of
nonroad equipment that was built after emission standards take effect
cannot be imported without a currently valid certificate of conformity.
We would consider it to be a new engine, vehicle, or vessel, which
would trigger a requirement to comply with the applicable emission
standards. Thus, for example, a marine vessel manufactured in a foreign
country in 2007, then imported into the United States in 2010, would be
considered ``new.'' The engines on that vessel would have to comply
with the requirements for the 2007 model year, assuming no other
exemptions apply. This provision is important to prevent manufacturers
from avoiding emission standards by building vessels or vehicles
abroad, transferring their title, and then importing them as used
vessels or vehicles.
Imported engines are generally subject to emission standards.
However, we are not adopting a definition of ``import'' in this
regulation. We will defer to the U.S. Customs Service for
determinations of when an engine or vehicle is imported into the U.S.
4. Do the Standards Apply to Exported Engines or Vehicles?
Engines or vehicles intended for export are generally not required
to meet the emission standards or other requirements adopted in this
rule. However, engines that will be exported and subsequently re-
imported into the United States must be covered by a certificate of
conformity. For example, this would occur when a foreign company
purchases engines manufactured in the United States for installation on
a marine vessel, recreational vehicle, or other nonroad equipment for
export back to the United States. Those engines would be subject to the
emission standards that apply on the date the engine was originally
manufactured. If the engine is later modified and certified (or
recertified), the engine is subject to emission standards that apply on
the date the modification is complete. So, for example, foreign boat
builders buying U.S.-made engines without recertifying the engines will
need to make sure they purchase complying engines for the products they
sell in the U.S. We also do not exempt engines exported to countries
that share our emission standards.
5. Are Any New Engines or Vehicles in the Applicable Categories Not
Subject to Emission Standards of This Rule?
We are extending our basic nonroad exemptions to the engines and
vehicles covered by this rulemaking. These include the testing
exemption, the manufacturer-owned exemption, the display exemption, and
the national-security exemption. These exemptions are described in more
detail in Section VII.C.
In addition, the Clean Air Act does not consider stationary engines
or engines used solely for competition to be nonroad engines, so the
emission standards do not apply to them. Refer to the program
discussions below for a description of how these exclusions or
exemptions apply for different categories of engines.
B. Emission Standards and Testing
1. Which Pollutants Are Covered by Emission Standards?
Engines subject to the exhaust emission standards must meet
standards based on measured levels of specified pollutants, such as
NOX, HC, or CO, though not all engines have standards for
each pollutant. Diesel engines generally must also meet a PM emission
standard. In addition, there may be standards or other requirements for
crankcase, evaporative, or permeation emissions, as described below.
The emission standards are effective on a model-year basis. We
define model year much like we do for passenger cars. It generally
means either the calendar year or some other annual production period
based on the manufacturer's production practices. A model year may
include January 1 from only one year.
[[Page 68257]]
For example, manufacturers could start selling 2006 model year engines
as early as January 2, 2005, as long as the production period extends
until at least January 1, 2006. All of a manufacturer's engines from a
given model year must meet emission standards for that model year. For
example, manufacturers producing new engines in the 2006 model year
need to comply with the 2006 standards. The model year of a particular
engine is determined based on the date that the engine is fully
assembled. In the case of recreational vehicles, this generally applies
to the final assembly of the whole vehicle, since the emission
standards apply to the vehicle. Refer to the individual program
discussions below or the regulations for additional information about
model year periods, including how to define what model year means in
less common scenarios, such as installing used engines in new
equipment.
2. What Standards Apply to Crankcase, Evaporative, Permeation, and
Other Emissions?
Blow-by of combustion gases and the reciprocating action of the
piston can cause exhaust emissions to accumulate in the crankcase of
four-stroke engines. Uncontrolled engine designs route these vapors
directly to the atmosphere, where they contribute to ambient levels of
hydrocarbons. We have long required that automotive engines prevent
emissions from their crankcases. Manufacturers typically do this by
routing crankcase vapors through a valve into the engine's air intake
system. We generally require in this rulemaking that engines control
crankcase emissions.
Vehicles with spark-ignition engines use fuel that is volatile and
the unburned fuel can be released into the ambient air. We are adopting
standards to limit evaporative emissions from the fuel. Evaporative
emissions result from heating gasoline or other volatile fuels in a
tank that is vented to the atmosphere or from permeation through
plastic fuel tanks and rubber hoses. Section IV describes the
permeation standards for recreational vehicles. Section V provides
additional information on the evaporative emission standards for Large
SI engines.
We are also adopting a general requirement that all engines subject
to this final rule may not cause or contribute to an unreasonable risk
to public health, welfare, or safety, especially with respect to
noxious or toxic emissions that may increase as a result of emission-
control technologies. The regulatory language has been modified
consistent with the alternate language suggested in the proposal. This
alternate language implements sections 202(a)(4) and 206(a)(3) of the
Act and clarifies that the purpose of this requirement is to prevent
control technologies that would cause unreasonable risks, rather than
to prevent trace emissions of any noxious compounds. For example, this
requirement would prevent the use of emission-control technologies that
produce high levels of pollutants for which we have not set emission
standards, but nevertheless pose a risk to the public. However, it
should be noted that this would generally not apply to exhaust gas
recirculation systems on gasoline- or diesel-fueled engines.
3. What Duty Cycles Is EPA Adopting for Emission Testing?
Testing an engine for exhaust emissions typically consists of
exercising it over a prescribed duty cycle of speeds and loads,
typically using an engine or chassis dynamometer. The duty cycle used
to measure emissions for certification, which is generally derived from
typical operation from the field, is critical in evaluating the likely
emissions performance of engines designed to emission standards.
Testing for recreational marine diesel engines and Large SI engines may
also include additional operation not included in the specific duty
cycles.
Steady-state testing consists of engine operation for an extended
period at several speed-load combinations. Associated with these test
points are weighting factors that allow calculation of a single
weighted-average steady-state emission level in g/kW. Transient testing
involves a continuous trace of specified engine or vehicle operation;
emissions are collected over the whole testing period for a single mass
measurement.
See Section VIII.C for a discussion of how we define maximum test
speed and intermediate speed for engine testing. Refer to the program
discussions below for more information about the type of duty cycle
required for testing the various engines and vehicles. Those sections
also include information regarding testing provisions that do not rely
on specific operating cycles (i.e., field-testing, not-to exceed
testing, and evaporative testing).
4. How Do Adjustable Engine Parameters Affect Emission Testing?
Many engines are designed with components that can be adjusted for
optimum performance under changing conditions, such as varying fuel
quality, high altitude, or engine wear. Examples of adjustable
parameters include spark timing, idle-speed setting, and fuel-injection
timing. While we recognize the need for this practice, we are also
concerned that engines maintain an appropriate level of emission
control for the whole range of adjustability. Manufacturers must
therefore show that their engines meet emission standards over the full
adjustment range. Manufacturers must also provide a physical stop to
prevent adjustment outside the established range. Operators are then
prohibited by the anti-tampering provisions from adjusting engines
outside this range.
5. What Are Voluntary Low-Emission Engines and Blue Sky Standards?
Several state and environmental groups and manufacturers of
emission controls have supported our efforts to develop incentive
programs to encourage engine technologies that go beyond federal
emission standards. Some companies have already significantly developed
these technologies. In the final rule for land-based nonroad diesel
engines, we included a program of voluntary standards for low-emitting
engines, referring to these as ``Blue Sky Series'' engines (63 FR
56967, October 23, 1998). We included similar programs for commercial
marine diesel engines. The general purposes of such programs are to
provide incentives to manufacturers to produce clean products, as well
as to create market choices and opportunities for environmental
information for consumers regarding such products.
We are adopting voluntary Blue Sky Series standards for some of the
engines subject to this final rule. Creating a program of voluntary
standards for low-emitting engines, including testing and durability
provisions to help ensure adequate in-use performance, will be a step
forward in advancing emission-control technologies. While these are
voluntary standards, they become binding once a manufacturer chooses to
participate. EPA certification will therefore provide protection
against false claims of environmentally beneficial products.
C. Demonstrating Compliance
We are adopting a compliance program to accompany the final
emission standards. This consists first of a process for demonstrating
that new engine models comply with the emission standards. In addition
to new-engine testing, several provisions ensure that emission-control
systems will continue to function over long-term
[[Page 68258]]
operation in the field. Most of these certification provisions are
consistent with previous rulemakings for other nonroad engines. Refer
to the discussion of the specific programs below for additional
information about these requirements for each engine category.
1. How Do I Certify My Engines?
We are adopting a certification process similar to that already
established for other nonroad engines. Manufacturers generally test
representative prototype engines and submit the emission data along
with other information to EPA in an application for a Certificate of
Conformity. If we approve the application, EPA issues a Certificate of
Conformity which allows the manufacturer to produce and sell the
engines described in the application in the U.S.
Manufacturers certify their engine models by grouping them into
engine families that have similar emission characteristics. The engine
family definition is fundamental to the certification process and to a
large degree determines the amount of testing required for
certification. The regulations include specific engine characteristics
for grouping engine families for each category of engines. To address a
manufacturer's unique product mix, we may approve using broader or
narrower engine families.
Engine manufacturers are responsible to build engines that meet the
emission standards over each engine's useful life. The useful life we
adopt by regulation is intended to reflect the period during which
engines are designed to properly function without being remanufactured
or the average service life. Useful life values, which are expressed in
terms of years or amount of operation (in hours or kilometers), vary by
engine category, as described in the following sections. Consistent
with other recent EPA programs, we generally consider this useful life
value in amount of operation to be a minimum value, requiring
manufacturers to comply for a longer period in those cases where their
engines operate longer than the minimum useful life.
The emission-data engine is the engine from an engine family that
will be used for certification testing. To ensure that all engines in
the family meet the standards, manufacturers must select the engine
most likely to exceed emission standards in a family for certification
testing. In selecting this ``worst-case'' engine, the manufacturer uses
good engineering judgment. Manufacturers consider, for example, all
engine configurations and power ratings within the engine family and
the range of installed options allowed. Requiring the worst-case engine
to be tested helps the manufacturer be sure that all engines within the
engine family are complying with emission standards. Manufacturers
estimate the rate of deterioration for each engine family over its
useful life and show that engines continue to meet standards after
incorporating the estimated deterioration. We may also test the engines
ourselves.
Manufacturers must include in their application for certification
the results of emission tests showing that the engine family meets
emission standards. In addition, we may ask the manufacturer to include
any additional data from their emission-data engines, including any
diagnostic-type measurements (such as ppm testing) and invalidated
tests. This complete set of test data ensures that the valid tests
forming the basis of the manufacturer's application are a robust
indicator of emission-control performance, rather than a spurious or
incidental test result.
We are adopting test-fuel specifications intended to represent in-
use fuels. Engines must be able to meet the standards on fuels with
properties anywhere in the specified ranges. The test fuel is generally
to be used for all testing associated with the regulations, including
certification, production-line testing, and in-use testing. Refer to
the program discussions below related to test fuel specifications.
We require engine manufacturers to give engine buyers instructions
for properly maintaining their engines. We are including limitations on
the frequency of scheduled maintenance that a manufacturer may specify
for emission-related components to help ensure that emission-control
systems don't depend on an unreasonable expectation of maintenance in
the field. These maintenance limits also apply during any service
accumulation that a manufacturer may do to establish deterioration
factors. This approach is common to all our engine programs. It is
important to note, however, that these provisions don't limit the
maintenance an operator may perform; it merely limits the maintenance
that operators can be expected to perform on a regularly scheduled
basis. Refer to the discussion of the specific programs below for
additional information about the allowable maintenance intervals for
each category of engines.
Once an engine family is certified, we require every engine a
manufacturer produces from the engine family to have a label with basic
identifying information. The design and content of engine labels is
specified in the regulations.
2. What Warranty Requirements Apply to Certified Engines?
Consistent with our current emission-control programs,
manufacturers must provide a design and defect warranty covering
emission-related components for a minimum period specified in the
regulations. This minimum period is generally half of the useful life
period. The regulations also provide that the manufacturer's emission
warranty period could be adjusted to a value higher than the minimum
period for those cases where the manufacturer provides a longer
mechanical warranty for the engine or any of its components; this
includes extended warranties that are available for an extra price. Any
such adjustment would be dependent on the average service life of the
vehicle as well. The manufacturer generally does not need to include
scheduled maintenance or other routine maintenance under the emission
warranty. See the regulation language for a detailed description of the
components that are considered to be emission-related.
If an operator makes a valid warranty claim for an emission-related
component during the warranty period, the engine manufacturer is
generally obligated to replace the component at no charge to the
operator. The engine manufacturer may deny warranty claims, however, if
the operator caused the component failure by misusing the engine or
failing to do necessary maintenance.
We are also adopting a defect reporting requirement that applies
separate from the emission-related warranty (see Section VII.F). In
general, defect reporting applies when a manufacturer discovers a
pattern of component failures, whether that information comes from
warranty claims, voluntary investigation of product quality, or other
sources.
3. Can I Use Emission Averaging To Show That I Meet Emission Standards?
Many of our mobile source emission-control programs include
voluntary use of emission credits to facilitate implementation of
emission controls. An emission-credit program is an important factor we
take into consideration in setting emission standards that are
appropriate under Clean Air Act section 213. An emission-credit program
can improve the technological feasibility and reduce the cost of
achieving standards, allowing us to consider a more stringent emission
standard than might otherwise be
[[Page 68259]]
appropriate, including a compliance date for the standards earlier than
would otherwise be appropriate. Manufacturers gain flexibility in
product planning and introduction of product lines meeting a new
standard. Emission-credit programs also create an incentive for the
early introduction of new technology, which allows certain engine
families to act as trailblazers for new technology. This can help
provide valuable information to manufacturers on the technology before
they apply the technology throughout their product line. This early
introduction of clean technology improves the feasibility of achieving
the standards and can provide valuable information for use in other
regulatory programs that may benefit from similar technologies.
Emission-credit programs may involve averaging, banking, or
trading. Averaging allows a manufacturer to certify one or more engine
families at emission levels above the applicable emission standards, as
long as the increased emissions from that engine family are offset by
one or more engine families certified below the applicable standards.
The over-complying engine families generate credits that are used by
the under-complying engine families. Compliance is determined taking
into account differences in production volume, power and useful life
among engine families. The average of all the engine families for a
particular manufacturer's production must be at or below the level of
the applicable emission standards. This calculation generally factors
in sales-weighted average power, production volume, and useful life.
Banking allows a manufacturer to generate emission credits and bank
them for future use in its own averaging program in later years.
Trading allows transfer of credits to another company.
In general, a manufacturer choosing to participate in an emission-
credit program certifies each participating engine family to a Family
Emission Limit. In its certification application, a manufacturer
determines a separate Family Emission Limit for each pollutant included
in the emission-credit program. The Family Emission Limit selected by
the manufacturer becomes the emission standard for each engine in that
engine family. Emission credits are based on the difference between the
emission standard that applies to the family and the Family Emission
Limit. Manufacturers must meet the Family Emission Limit for all
emission testing of any engine in that family. At the end of the model
year, manufacturers must show that the net effect of all their engine
families participating in the emission-credit program is a zero balance
or a net positive balance of credits. A manufacturer may generally
choose to include only a single pollutant from an engine family in the
emission-credit program or, alternatively, to establish a Family
Emission Limit for each of the regulated pollutants. Refer to the
program discussions below for more information about emission-credit
provisions for individual engine categories.
4. What Are the Production-Line Testing Requirements?
We are adopting production-line testing requirements for
recreational marine diesel engines, recreational vehicles, and Large SI
engines. Manufacturers must routinely test production-line engines to
help ensure that newly assembled engines control emissions at least as
well as the emission-data engines tested for certification. Production-
line testing serves as a quality-control step, providing information to
allow early detection of any problems with the design or assembly of
freshly manufactured engines. This is different than selective
enforcement auditing, in which we would give a test order for more
rigorous testing for a small subset of production-line engines in a
particular engine family (see Section VII.E). Production-line testing
requirements are already common to several categories of nonroad
engines as part of their emission-control program.
If an engine fails to meet an emission standard, the manufacturer
must modify it to bring that specific engine into compliance.
Manufacturers may adjust the engine family's Family Emission Limit to
take into account the results from production-line testing (if
applicable). If too many engines exceed emission standards, this
indicates it is more of a family-wide problem and the manufacturer must
correct the problem for all affected engines. The remedy may involve
changes to assembly procedures or engine design, but the manufacturer
must, in any case, do sufficient testing to show that the engine family
complies with emission standards before producing more engines. The
remedy may also need to address engines already produced since the last
showing that production-line engines met emission standards.
The production-line testing programs for Large SI engines and for
recreational vehicles depend on the Cumulative Sum (CumSum) statistical
process for determining the number of engines a manufacturer needs to
test (see the regulations for the specific calculation methodology).
Each manufacturer generally selects engines randomly at the beginning
of each new quarter.\36\ If engines must be tested at a facility where
final assembly is not yet completed, manufacturers must randomly select
engine components and assemble the test engine according to their
established assembly instructions. The Cumulative Sum program uses the
emission results to calculate the number of tests required for the
remainder of the year to reach a pass or fail determination for
production-line testing. If tested engines have emissions close to the
standard, the statistical sampling method calls for an increased number
of tests to show whether to make a pass or fail determination for the
engine family. The remaining number of tests is recalculated after the
manufacturer tests each engine. Engines selected should cover the
broadest range of production configurations possible. Tests should also
be distributed evenly throughout the sampling period to the extent
possible.
---------------------------------------------------------------------------
\36\ We consider an engine to be randomly selected if it
undergoes normal assembly and manufacturing procedures. An engine is
not randomly selected if it has been built with any kind of special
components or procedures.
---------------------------------------------------------------------------
If an engine family fails the production-line testing criteria, we
may suspend the Certificate of Conformity. Under the CumSum approach,
individual engines can exceed the emission standards without causing
the whole engine family to exceed the production-line testing criteria.
The production-line testing criteria are designed to determine if there
is a problem that applies broadly across the engine family. Whether or
not the production-line testing criteria are met, manufacturers must
adjust or repair every failing engine and retest it to show that it
meets the emission standards. Note also that all production-line
emission measurements must be included in the periodic reports to us.
This includes any type of screening or surveillance tests (including
ppm measurements), all data points for evaluating whether an engine
controls emissions ``off-cycle,'' and any engine tests that exceed the
minimum required level of testing.
The regulations allow us to reduce testing requirements for engine
families that consistently pass the production-line testing criteria.
For engine families that pass all of the production-line test
requirements for two consecutive years, the manufacturer may request a
reduced testing rate. The minimum testing rate is one test per engine
family for one year. Our approval for a reduced testing rate may be
limited to a single model year,
[[Page 68260]]
but manufacturers may continue to request reduced testing rates.
As we have concluded in other engine programs, some manufacturers
may have unique circumstances that call for different methods to show
that production engines comply with emission standards. A manufacturer
may therefore suggest an alternate plan for testing production-line
engines, as long as the alternate program is as effective at ensuring
that the engines will comply. A manufacturer's petition to use an
alternate plan should address the need for the alternative and should
justify any changes from the regular testing program. The petition must
also describe in detail the equivalent thresholds and failure rates for
the alternate plan. If we approve the plan, we will use these criteria
to determine when an engine family passes or fails the production-line
testing criteria. It is important to note that this allowance is
intended only as a flexibility, and is not intended to affect the
stringency of the standards or the production-line testing program.
Refer to the specific program discussions below for additional
information about production-line testing for different types of
engines.
D. Other Concepts
1. What Are Emission-Related Installation Instructions?
Manufacturers selling loose engines to equipment manufacturers must
develop a set of emission-related installation instructions. These
instructions include anything the installer needs to know to ensure
that the engine operates within its certified design configuration. For
example, the installation instructions could specify a total capacity
needed from the engine cooling system, placement of catalysts after
final assembly, or specification of parts needed to control evaporative
or permeation emissions. We approve emission-related installation
instructions as part of the certification process. If equipment
manufacturers fail to follow the established emission-related
installation instructions, we will consider this tampering, which may
subject them to significant civil penalties. Refer to the program
discussions below for more information about specific provisions
related to installation instructions.
2. Are There Special Provisions for Small Manufacturers of These
Engines and Vehicles?
The scope of this rule includes many engine and vehicle
manufacturers that have previously not been subject to our mobile
source regulations or certification process. Some of these
manufacturers are small businesses, with unique concerns relating to
the compliance burden from the general regulating program. The sections
describing the emission-control program include discussion of special
compliance provisions designed to address this for the different engine
categories.
III. Recreational Vehicles and Engines
A. Overview
We are adopting new exhaust emission standards for snowmobiles,
off-highway motorcycles, and all-terrain vehicles (ATVs). The engines
used in these vehicles are a subset of nonroad SI engines.\37\ In our
program to set exhaust emission standards for nonroad spark-ignition
engines below 19 kW (Small SI), we excluded recreational vehicles
because they have different design characteristics and usage patterns
than certain other engines in the Small SI category. For example,
engines typically found in the Small SI category are used in lawn
mowers, chainsaws, trimmers, and other lawn and garden applications.
These engines tend to have low power outputs and operate at constant
loads and speeds, whereas recreational vehicles can have high power
outputs with highly variable engine loads and speeds. This suggests
that these engines should be regulated differently than Small SI
engines. In the same way, we treat snowmobiles, off-highway
motorcycles, and ATVs separately from our Large SI engine program,
which is described in Section V. Recreational vehicles that are not
snowmobiles, off-highway motorcycles, or ATVs, will be subject to the
standards that otherwise apply to small nonroad spark-ignition engines
(see Section III.B.2).
---------------------------------------------------------------------------
\37\ Almost all recreational vehicles are equipped with spark-
ignition engines. Any diesel engines used in these applications must
meet our emission standards for nonroad diesel engines.
---------------------------------------------------------------------------
We are adopting exhaust emission standards for HC and CO from all
recreational vehicles. We are adopting an additional requirement to
control NOX from off-highway motorcycles and ATVs. We
believe that vehicle and engine manufacturers will be able to use
technology already established for other types of engines, such as
highway motorcycles, small spark-ignition engines, and marine engines,
to meet these standards. We recognize that some small businesses
manufacture recreational vehicles; we are therefore adopting several
special compliance provisions to reduce the burden of emission
regulations on small businesses.
1. What Are Recreational Vehicles and Who Makes Them?
We are adopting new exhaust emission standards for off-highway
motorcycles, ATVs, and snowmobiles. Eight large manufacturers dominate
the sales of these recreational vehicles. Of these eight manufacturers,
seven of them manufacture two or more of the three main types of
recreational vehicles. For example, there are four companies that
manufacture both off-highway motorcycles and ATVs. There are three
companies that manufacture ATVs and snowmobiles; one company
manufactures all three. These eight companies represent approximately
95 percent of all domestic sales of recreational vehicles.
a. Off-highway motorcycles. Motorcycles are two-wheeled, self-
powered vehicles that come in a variety of configurations and styles.
Off-highway motorcycles are similar in appearance to highway
motorcycles, but there are several important distinctions between the
two types of machines. Off-highway motorcycles are not street-legal and
are primarily operated on public and private lands over trails and open
areas. A significant number are used in competition events. Off-highway
motorcycles tend to be much smaller, lighter and more maneuverable than
their larger highway counterparts. They are equipped with relatively
small-displacement single-cylinder two- or four-stroke engines ranging
from 48 to 650 cubic centimeters (cc) in size. The exhaust systems for
off-highway motorcycles are distinctively routed high on the frame to
prevent damage from brush, rocks, and water. Off-highway motorcycles
are designed to be operated over varying surfaces, such as dirt, sand,
or mud, and are equipped with knobby tires to give better traction in
off-road conditions. Unlike highway motorcycles, off-highway
motorcycles have fenders mounted far from the wheels and closer to the
rider to keep dirt and mud from spraying the rider and clogging between
the fender and tire. Off-highway motorcycles are also equipped with
more advanced suspension systems than those for highway motorcycles.
This allows the operator to ride over obstacles and make jumps safely.
Five companies dominate sales of off-highway motorcycles. They are
long-established, large corporations that manufacture several different
products including highway and off-highway motorcycles. These five
companies account for 90 to 95 percent of all
[[Page 68261]]
domestic sales of off-highway motorcycles. There are also several
relatively small companies that manufacture off-highway motorcycles,
many of which specialize in competition machines.
b. All-terrain vehicles. The earliest ATVs were three-wheeled off-
highway models with large balloon tires that existed in the early
1970's. Due to safety concerns, the three-wheeled ATVs were phased-out
in the mid-1980s and replaced by the current and more popular four-
wheeled vehicle known as ``quad runners'' or simply ``quads.'' Quads
resemble the earlier three-wheeled ATVs except that the single front
wheel was replaced with two wheels. The ATV steering system uses
motorcycle handlebars, rather than a steering wheel. The operator sits
on and rides the quad much like a motorcycle. The engines used in quads
tend to be very similar to those used in off-highway motorcycles--
relatively small, single-cylinder two- or four-stroke engines. Quads
are typically divided into utility and sport models. The utility quads
are designed for multi-function use and have the ability to perform
many utility functions, such as plowing snow, tilling gardens, and
mowing lawns in addition to use for recreational riding. They are
typically heavier and equipped with relatively large four-stroke
engines and automatic transmissions with a reverse gear. Sport quads
are smaller and lighter and designed primarily for recreational
purposes. They are equipped with two- or four-stroke engines and manual
transmissions. Presently utility ATVs comprise about 75 percent of the
market and sport models about 25 percent.
Of all of the types of recreational vehicles, ATVs have the largest
number of major manufacturers. All but one of the companies noted above
for off-highway motorcycles and below for snowmobiles are significant
ATV producers. These seven companies represent over 95 percent of total
domestic ATV sales. The remaining 5 percent of sales come from
importers, which tend to import less expensive, youth-oriented ATVs.
As discussed below, we are requiring utility vehicles capable of
speeds above 25 mph to comply the regulations for ATVs.
c. Snowmobiles. Snowmobiles, also referred to as ``sleds,'' are
tracked vehicles designed to operate over snow. Snowmobiles have some
similarities to off-highway motorcycles and ATVs. A snowmobile rider
sits on and rides a snowmobile similar to an ATV. Snowmobiles use high-
powered two- and three-cylinder two-stroke engines that look similar to
off-highway motorcycle engines. Rather than wheels, snowmobiles are
propelled by a track system similar to what is used on a bulldozer. The
snowmobile is steered by two skis at the front of the sled. Snowmobiles
use handlebars similar to off-highway motorcycles and ATVs. The typical
snowmobile seats two riders comfortably. Over the years, snowmobile
performance has steadily increased to the point that many snowmobiles
currently have engines over 100 horsepower and are capable of exceeding
100 miles per hour. The definition for snowmobiles includes a limit of
1.5-meter width to differentiate conventional snowmobiles from ice-
grooming machines and snow coaches, which use very different engines.
There are four major snowmobile manufacturers, accounting for more
than 99 percent of all domestic sales. The remaining sales come from
very small manufacturers who tend to specialize in high-performance
designs.
d. Other recreational vehicles. Currently, our Small SI nonroad
engine regulations cover all recreational engines that are under 19 kW
(25 hp) and have either an installed speed governor or a maximum engine
speed less than 5,000 revolutions per minute (rpm). Recreational
vehicles currently covered by the Small SI standards include go-carts,
golf carts, and small mini-bikes. Although some off-highway
motorcycles, ATVs and snowmobiles have engines with rated horsepower
less than 19 kW, they all have maximum engine speeds greater than 5,000
rpm. Thus they have not been included in the Small SI regulations. The
only other types of small recreational engines not covered by the Small
SI rule are those engines under 19 kW that aren't governed and have
maximum engine speed of at least 5,000 rpm. There are relatively few
such vehicles with recreational engines not covered by the Small SI
regulations. The best example of vehicles that fit in this category are
stand-on scooters and skateboards that have been equipped with very
small gasoline spark-ignition engines. The engines used on these
vehicles are typically the same as those used in string trimmers or
other lawn and garden equipment, which are covered under the Small SI
regulations. Because these engines are generally already covered by the
Small SI regulations and are the same as, or very similar to, engines
as those used in lawn and garden applications, we are revising the
Small SI rules to cover these engines under the Small SI regulations.
To avoid any problems in transitioning to meet emission standards, we
are applying these standards beginning in 2006. We did not receive any
comments on this approach.
2. What Is the Regulatory History for Recreational Vehicles?
The California Air Resources Board (California ARB) established
standards for off-highway motorcycles and ATVs, which took effect in
January 1997 (1999 for vehicles with engines of 90 cc or less).
California has not adopted standards for snowmobiles. The standards,
shown in Table III.A-1, are based on the highway motorcycle chassis
test procedures. Manufacturers may certify ATVs to optional standards,
also shown in Table III.A-1, which are based on the utility engine test
procedure.\38\ This is the test procedure over which Small SI engines
are tested. The stringency level of the standards was based on the
emission performance of small four-stroke engines and advanced two-
stroke engines with a catalytic converter. California ARB anticipated
that the standards would be met initially by using high-performance
four-stroke engines.
---------------------------------------------------------------------------
\38\ Notice to Off-Highway Recreational Vehicle Manufacturers
and All Other Interested Parties Regarding Alternate Emission
Standards for All-Terrain Vehicles, Mail Out #95-16, April
28, 1995, California ARB (Docket A-2000-01, document II-D-06).
III.A-1--California Off-highway Motorcycle and ATV Standards for Model Year 1997 and later
[1999 and later for engines at or below 90 cc]
----------------------------------------------------------------------------------------------------------------
HC NOX CO PM
----------------------------------------------------------------------------------------------------------------
Off-highway motorcycle and ATV standards (g/km). \a\ 1.2 .............. 15 ..............
----------------------------------------------------------------------------------------------------------------
[[Page 68262]]
----------------------------------------------------------------------------------------------------------------
HC + NOX CO PM
--------------------------------------------------------------------------------------------------
Optional standards for ATV engines below 225 cc (g/ \a\ 12.0 300 ..............
bhp-hr)..........................................
Optional standards for ATV engines at or above 225 \a\ 10.0 300 ..............
cc (g/bhp-hr)....................................
----------------------------------------------------------------------------------------------------------------
a Corporate-average standard.
California revisited the program because a lack of certified off-
highway motorcycles from manufacturers was reportedly creating economic
hardship for dealerships. The number of certified off-highway
motorcycle models was particularly inadequate.\39\ In 1998, California
revised the program, allowing the uncertified products in off-highway
vehicle recreation areas with regional/seasonal use restrictions.
Currently, noncomplying vehicles may be sold in California and used in
attainment areas year-round and in nonattainment areas during months
when exceedances of the state ozone standard are not expected. For
enforcement purposes, certified and uncertified products are identified
with green and red stickers, respectively. Only about one-third of off-
highway motorcycles selling in California are certified. All certified
products have four-stroke engines.
---------------------------------------------------------------------------
\39\ Initial Statement of Reasons, Public Hearing to Consider
Amendments to the California Regulations for New 1997 and Later Off-
highway Recreational Vehicles and Engines, California ARB, October
23, 1998 (Docket A-2000-01, document II-D-08).
---------------------------------------------------------------------------
B. Engines Covered by This Rule
We are adopting new emission standards for new off-highway
motorcycles, ATVs, and snowmobiles. (We are also applying existing
Small SI emission standards to other recreational equipment, as
described above.) The engines used in recreational vehicles tend to be
small, air- or liquid-cooled, reciprocating Otto-cycle engines that
operate on gasoline.\40\ Engines used in vehicle applications
experience engine performance that is characterized by highly transient
operation, with a wide range of engine speed and load capability.
Maximum engine speed are typically well above 5,000 rpm. Also, with the
exception of snowmobiles, the vehicles are typically equipped with
transmissions rather than torque converters to ensure performance under
a variety of operating conditions.\41\
---------------------------------------------------------------------------
\40\ Otto-cycle is another name for a reciprocating, internal-
combustion engine that uses a spark to ignite a homogeneous air and
fuel mixture, in which air-fuel mixing may occur inside or outside
the combustion chamber.
\41\ Snowmobiles use continuously variable transmissions, which
tend to operate like torque converters.
---------------------------------------------------------------------------
1. Two-Stroke vs. Four-Stroke Engines
The engines used by recreational vehicles can be separated into two
distinct designs: two-stroke and four-stroke. The distinction between
two-stroke and four-stroke engines is important for emissions because
two-stroke engines tend to emit much greater amounts of unburned HC and
PM than four-stroke engines of similar size and power. Two-stroke
engines have lower NOX emissions than do four-stroke engines
because they experience a significant amount of internal exhaust gas
recirculation resulting from exhaust gases being drawn back into the
combustion chamber on the piston's downward stroke while the exhaust
port is uncovered. Exhaust gas is inert and displaces fresh fuel and
air that could otherwise be combusted, which creates lower in-cylinder
temperatures and thus less NOX. Two-stroke engines also have
greater fuel consumption than four-stroke engines, but they also tend
to have higher power output per-unit displacement, lighter weight, and
better cold-starting performance. These, and other characteristics,
tend to make two-stroke engines popular as a power unit for
recreational vehicles. With the exception of a few youth and touring
models, almost all snowmobiles use two-stroke engines. Currently, about
63 percent of all off-highway motorcycles (predominantly in high-
performance, youth, and entry-level bikes) and 20 percent of all ATVs
sold in the United States use two-stroke engines.
The basis for the differences in engine performance and exhaust
emissions between two-stroke and four-stroke engines can be found in
the fundamental differences in how two-stroke and four-stroke engines
operate. Four-stroke operation takes place in four distinct steps:
intake, compression, power, and exhaust. Each step corresponds to one
up or down stroke of the piston or 180[deg]
of crankshaft rotation. The
first step of the cycle is for an intake valve in the combustion
chamber to open during the intake stroke, allowing a mixture of air and
fuel to be drawn into the cylinder while the piston moves down the
cylinder. The intake valve then closes and the momentum of the
crankshaft causes the piston to move back up the cylinder, compressing
the air and fuel mixture. At the very end of the compression stroke,
the air and fuel mixture is ignited by a spark from a spark plug and
begins to burn. As the air and fuel mixture burns, increasing
temperature and pressure cause the piston to move back down the
cylinder. This is referred to as the ``power'' stroke. At the bottom of
the power stroke, an exhaust valve opens in the combustion chamber and
as the piston moves back up the cylinder, the burnt gases are pushed
out through the exhaust valve to the exhaust manifold, and the cycle is
complete.
In a four-stroke engine, combustion and the resulting power stroke
occur only once every two revolutions of the crankshaft. In a two-
stroke engine, combustion occurs every revolution of the crankshaft.
Two-stroke engines eliminate the intake and exhaust strokes, leaving
only compression and power strokes. This is due to the fact that two-
stroke engines do not use intake and exhaust valves. Instead, they have
intake and exhaust ports in the sides of the cylinder walls. With a
two-stroke engine, as the piston approaches the bottom of the power
stroke, it uncovers exhaust ports in the wall of the cylinder. The high
pressure combustion gases blow into the exhaust manifold. As the piston
gets closer to the bottom of the power stroke, the intake ports are
uncovered, and fresh mixture of air and fuel are forced into the
cylinder while the exhaust ports are still open. Exhaust gas is
``scavenged'' or forced into the exhaust by the pressure of the
incoming charge of fresh air and fuel. In the process, however, some
mixing between the exhaust gas and the fresh charge of air and fuel
takes place, so that some of the fresh charge is also emitted in the
exhaust. Losing part of the fuel out of the exhaust during scavenging
causes very high hydrocarbon emission characteristics of two-stroke
engines. The other major reason for high HC emissions from two-stroke
engines is their tendency to misfire under low-load conditions due to
greater combustion instability.
2. Applicability of Small SI Regulations
In our regulations for Small SI engines, we established criteria,
such as rated engine speed at or above 5,000 rpm and the use of a speed
governor, that excluded engines used in certain types of recreational
vehicles (see 40 CFR 90.1(b)(5)). Engines used in some other types of
recreational vehicles may be covered by the Small SI standards,
depending on the characteristics of the engines. For example,
lawnmower-type
[[Page 68263]]
engines used in go carts are typically covered by the Small SI
standards because they don't operate above 5000 rpm. Similarly, engines
used in golf carts are included in the Small SI program. As discussed
above, we are revising the Small SI regulations to include all
recreational engines except those in off-highway motorcycles, ATVs,
snowmobiles, and hobby engines. Golf cart and go-cart engines will
remain in the Small SI program because the vehicles are not designed
for operation over rough terrain and do not meet the definition of ATV.
We are accordingly removing the 5,000 rpm and speed governor criteria
from the applicability provisions of the Small SI regulations.
3. Utility Vehicles
We proposed to define ATV as a ``nonroad vehicle with three or more
wheels and a seat designed for operation over rough terrain and
intended primarily for transportation'', and that it would include
``both land-based and amphibious vehicles''. We requested comment on
the proposed definition and based on comments, we are modifying the
definition to clearly exclude utility vehicles not capable of reaching
25 mph. Utility vehicles differ from ATVs in several ways. As stated
earlier, an ATV is operated and ridden very similar to a motorcycle,
with the rider straddling the seat and using handlebars to steer the
vehicle. The throttle and brakes are located on the handle bars,
similar to a motorcycle and snowmobile. Utility vehicles look and
operate very similarly to golf carts. The operator sits on a bench seat
with a back support that holds two or more passengers. Rather than
handlebars, utility vehicles use a steering wheel and have throttle and
brake pedals on the floor, similar to an automobile. Utility vehicles
also typically have a cargo box or bed (similar to that found on a
pick-up truck) used for hauling cargo. We define an off-highway utility
vehicle as a ``nonroad vehicle that has four or more wheels, seating
for two or more persons, is designed for operation over rough terrain,
and has either a rear payload of 350 pounds or more or seating for six
or more passengers.'' We are requiring utility vehicles capable of high
speed operation (speeds greater than 25 mph) to meet ATV standards. For
utility vehicles that are permanently governed and not capable of
reaching 25 mph, manufacturers must either continue to certify them to
the Small SI standards (or Large SI standards, if applicable) or
optionally certify them to the new ATV standards.
We received comments from the Outdoor Power Equipment Institute
(OPEI) that the definition should be clarified to exclude utility
vehicles. Most utility vehicles are equipped with engines that are
currently required to meet EPA Small SI standards. OPEI commented that
utility vehicles are designed specifically for work related tasks and
are equipped with seating for passengers, a bed for cargo, and riding-
mower-style controls.
The industry differentiates between utility vehicles based on
vehicle speed. The vast majority of utility vehicles are considered
``low-speed utility vehicles'' (LUVs) and are vehicle speed governed
with maximum speed of less than 25 mph. The engines used in such
vehicles are generally below 25 hp and are typically used in other lawn
and garden or utility applications such as generators or lawn tractors.
The engines differ significantly from those used in recreational
products which are designed for higher rpm operation with an emphasis
on higher performance. OPEI also provided comment on a newer type of
utility vehicle, which uses a more powerful (over 19kW) ATV-based
engine and is capable of speeds of up to 40 mph.
We are finalizing the approach described. The engines used in low-
speed utility vehicles are more similar in design and use to utility
engines than ATVs. The engines used to power these vehicles are often
used in other utility applications, such as lawn and garden tractors
and generators and are typically produced by companies that specialize
in utility and lawn equipment rather than power sport vehicles. These
products are already certified to the Small SI standards.
However, we have some concerns with continuing to use the Small SI
program test cycle for engines used in applications that operate at
broad engine speeds. The cycle was developed primarily for push
lawnmowers and other equipment that operates in a narrow band of engine
speeds. The Small SI test cycle measures emissions only at a single
high engine speed. We are concerned that the Small SI test cycle may
not achieve the same emission reductions for off-highway utility
vehicles in use as it would for lawnmowers, especially as more
stringent standards go into effect. The concern also applies to other
large ride-on equipment in the Small SI program, such as riding lawn
mowers, where engine speed is inherently variable. While the ATV
program may not be appropriate for these low-speed utility applications
due to operating and design differences, the Small SI program as it is
currently designed may not be completely appropriate either. Since we
did not propose changes for the Small SI program which currently
applies to utility vehicles and need to further study the issues, we
are not finalizing such changes to the Small SI program in this Final
Rule. We plan to continue to study the issue and, if necessary, address
it through a future rulemaking for the Small SI program.
In addition to test cycle, there are other reasons we plan to
continue to examine the appropriateness of the Small SI program for
large ride-on equipment. With respect to useful life, we are concerned
that off-highway utility vehicles may be designed to last significantly
longer than the typical lawnmower. 40 CFR 90.105 specifies useful life
values that vary by application with the longest useful life being 1000
hours. It is not clear that this maximum value is high enough to
address the expected life of in-use off-highway utility vehicles,
especially those that are used commercially. Finally, with respect to
the level of the standards, we are concerned about the relative
stringency of the Small SI standards relative to the long-term
standards for ATVs and other nonroad vehicles. Nevertheless, given the
low-speed operation of these vehicles, and other differences, we do not
believe that they should be treated the same as higher speed ATVs. We
did not propose changes for the Small SI program to address the above
issues and need to study them further. However, these vehicles are
unique in many ways, and should be addressed in a future rulemaking.
Given the utility nature of the low-speed vehicles, we believe that
at least for now, it is appropriate to continue to certify them under
40 CFR part 90. For vehicles capable of higher speeds (e.g., greater
than 25 mph), the engine designs and vehicle in-use operation is likely
to be more like ATVs. The test procedures and standards for ATVs will
better fit these high speed vehicles than those in the Small SI
program. For regulatory purposes, we are defining an off-highway
utility vehicle as a nonroad vehicle that has four or more wheels,
seating for two or more persons, is designed for operation over rough
terrain, and has either a rear payload capacity of 350 pounds or more
or total seating for six or more passengers.
4. Hobby Engines
The Small SI rule categorized spark-ignition engines used in model
cars, boats, and airplanes as recreational engines and exempted them
from the
[[Page 68264]]
Small SI program.\42\ We are continuing to exclude hobby engines from
the Small SI program because of significant engine design and use
differences. We also believe that hobby engines are substantially
different than engines used in recreational vehicles and, as proposed,
we are not including spark-ignition hobby engines in this final rule.
We received no comment on our proposed treatment of hobby engines or
any additional information on their design or use.
---------------------------------------------------------------------------
\42\ 80 FR 24292, April 25, 2000.
---------------------------------------------------------------------------
There are about 8,000 spark-ignition engines sold per year for use
in scale-model aircraft, cars, and boats.\43\ This is a very small
subsection of the overall model engine market, most of which are glow-
plug engines that run on a mix of castor oil, methyl alcohol, and nitro
methane.\44\ A typical spark-ignition hobby engine is approximately 25
cc with a horsepower rating of about 1-3 hp, though larger engines are
available. These spark-ignition engines are specialty products sold in
very low volumes, usually not more than a few hundred units per engine
line annually. Many of the engines are used in model airplanes, but
they are also used in other types of models such as cars and boats.
These engines, especially the larger displacement models, are
frequently used in competitive events by experienced operators. The
racing engines sometimes run on methanol instead of gasoline. In
addition, the engines are usually installed and adjusted by the
hobbyist who selects an engine that best fits the particular model
being constructed.
---------------------------------------------------------------------------
\43\ Comments submitted by Hobbico on behalf of Great Plains
Model Distributors and Radio Control Hobby Trade Association,
February 5, 2001, Docket A-2000-01, document II-D-58.
\44\ Hobby engines with glow plugs are considered compression-
ignition (diesel) engines because they lack a spark-ignition system
and a throttle (see the definition of compression-ignition, 40 CFR
89.2). The nonroad diesel engine regulations 40 CFR part 89
generally do not apply to hobby engines, so these engines are
unregulated.
---------------------------------------------------------------------------
The average annual hours of operation has been estimated to be
about 12.2 hours per year.\45\ The usage rate is very low compared to
other recreational or utility engine applications due to the nature of
their use. Much of the hobby revolves around building the model and
preparing the model for operation. The engine and model must be
adjusted, maintained, and repaired between uses.
---------------------------------------------------------------------------
\45\ Comments submitted by Hobbico on behalf of Great Plains
Model Distributors and Radio Control Hobby Trade Association,
February 5, 2001, Docket A-2000-01, document II-D-58.
---------------------------------------------------------------------------
Spark-ignition model engines are highly specialized and differ
significantly in design compared to engines used in other recreational
or utility engine applications. While some of the basic components such
as pistons may be similar, the materials, airflow, cooling, and fuel
delivery systems are considerably different.46 47 Some
spark-ignition model engines are scale replicas of multi-cylinder
aircraft or automobile engines and are fundamentally different than
spark-ignition engines used in other applications. Model-engine
manufacturers often select lighter-weight materials and simplified
designs to keep engine weight down, often at the expense of engine
longevity. Hobby engines use special ignition systems designed
specifically for the application to be lighter than those used in other
applications. To save weight, hobby engines typically lack pull
starters that are found on other engines. Hobby engines must be started
by spinning the propeller. In addition, the models themselves vary
significantly in their design, introducing packaging issues for engine
manufacturers.
---------------------------------------------------------------------------
\46\ E-mail from Carl Maroney of the Academy of Model
Aeronautics to Christopher Lieske, of EPA, June 4, 2001, Docket A-
2000-01, document II-G-144.
\47\ Comments submitted by Hobbico on Behalf of Great Plains
Model Distributors and Radio Control Hobby Trade Association,
February 5, 2001, Docket A-2000-01, document II-D-58.
---------------------------------------------------------------------------
We are not including spark-ignition hobby engines in the
recreational vehicles program. The engines differ significantly from
other recreational engines in their design and use, as noted above.
Emission-control strategies envisioned for other recreational vehicles
may not be well suited for hobby engines because of their design,
weight constraints, and packaging limitations. Approaches such as using
a four-stroke engine, a catalyst, or fuel injection all would involve
increases in weight, which would be particularly problematic for model
airplanes. The feasibility of these approaches for these engines is
questionable. Reducing emissions, even if feasible, would likely
involve fundamental engine redesign and substantial R&D efforts. The
costs of achieving emission reductions are likely to be much higher per
engine than for other recreational applications because the R&D costs
would be spread over very low sales volumes. The cost of fundamentally
redesigning the engines could double the cost of some engines.
By contrast, because of their very low sales volumes, annual usage
rates, and relatively short engine life cycle, spark-ignition hobby
engine emission contributions are extremely small compared to
recreational vehicles. The emission reductions possible from regulating
such engines would be minuscule (we estimate that spark-ignition hobby
engines as a whole account for less than 30 tons of HC nationally per
year, much less than 0.01 percent of mobile source HC emissions).\48\
---------------------------------------------------------------------------
\48\ For further information on the feasibility, emission
inventories, and costs, see ``Analysis of Spark Ignition Hobby
Engines'', Memorandum from Chris Lieske to Docket A-2000-01,
document II-G-144.
---------------------------------------------------------------------------
In addition, hobby engines differ significantly in their in-use
operating characteristics compared to small utility engines and other
recreational vehicle engines. It is unclear if the test procedures
developed and used for other types of spark-ignition engine
applications would be sufficiently representative or even technically
practical for hobby engines. We are not aware of any efforts to develop
an emission test cycle or conduct any emission testing of these
engines. Also, because installing, optimizing, maintaining, and
repairing the engines are as much a part of the hobby as operating the
engine, emission standards could fundamentally alter the hobby itself.
Engines with emission-control systems would be more complex and the
operator would need to be careful not to make changes that would cause
the engine to exceed emission standards. EPA will continue to review
these issues, as necessary, in the future and reconsider adoption of
regulations if appropriate.
5. Competition Exemptions
a. Off-Highway motorcycles. Currently, a large portion of off-
highway motorcycles are designed as competition/racing motorcycles.
These models often represent a manufacturer's high-performance
offerings in the off-highway market. Most such motorcycles are of the
motocross variety, although some high-performance enduro models are
marketed for competition use.49 50 These high-performance
motorcycles are
[[Page 68265]]
largely powered by two-stroke engines, though some four-stroke models
have been introduced in recent years.
---------------------------------------------------------------------------
\49\ A motocross bike is typically a high-performance off-
highway motorcycle that is designed to be operated in motocross
competition. Motocross competition is defined as a circuit race
around an off-highway closed-course. The course contains numerous
jumps, hills, flat sections, and bermed or banked turns. The course
surface usually consists of dirt, gravel, sand, and mud. Motocross
bikes are designed to be very light for quick handling and easy
maneuverability. They also come with large knobby tires for
traction, high fenders to protect the rider from flying dirt and
rocks, aggressive suspension systems that allow the bike to absorb
large amounts of shock, and are powered by high-performance engines.
They are not equipped with lights.
\50\ An enduro bike is very similar in design and appearance to
a motocross bike. The primary difference is that enduros are
equipped with lights and have slightly different engine performance
that is more geared towards a broader variety of operation than a
motocross bike. An enduro bike needs to be able to cruise at high
speeds as well as operate through tight woods or deep mud.
---------------------------------------------------------------------------
Competition events for motocross motorcycles mostly involve closed-
course or track racing. Other types of off-highway motorcycles, such as
enduros and trials bikes, are usually marketed for trail or open-area
use. When used for competition, these models are likely to be involved
in point-to-point competition events over trails or stretches of open
land. There are also specialized off-highway motorcycles that are
designed for competitions such as ice racing, drag racing, and observed
trials competition. A few races involve professional manufacturer-
sponsored racing teams. Amateur competition events for off-highway
motorcycles are also held frequently in many areas of the U.S.
Clean Air Act subsections 216 (10) and (11) exclude engines and
vehicles ``used solely for competition'' from nonroad engine and
nonroad vehicle regulations. In the proposal we stated that in previous
nonroad engine emission-control programs, we have generally defined the
term as follows:
Used solely for competition means exhibiting features that are not
easily removed and that would render its use other than in competition
unsafe, impractical, or highly unlikely.
Most motorcycles marketed for competition do not appear to have
obvious physical characteristics that constrain their use solely to
competition. In fact, they are usually sold by dealers from the
showroom floor. Upon closer inspection, however, there are several
features and characteristics for many competition motorcycles that make
recreational use unlikely. For example, motocross bikes are not
equipped with lights or a spark arrester, which prohibits them from
legally operating on public lands (such as roads, parks, state land,
and federal land).\51\ Vehicle performance of modern motocross bikes is
so advanced (for example, with extremely high power-to-weight ratios
and advanced suspension systems) that it is highly unlikely that these
machines will be used for recreational purposes. In addition, motocross
and other competition off-highway motorcycles typically do not come
with a warranty, which further deters purchasing and using competition
bikes for recreational operation.\52\ We believe these features are
sufficient in distinguishing competition motorcycles from recreational
motorcycles. Therefore, we are specifically adopting the following
features as indicative of motorcycles used solely for competition:
absence of a headlight or other lights; the absence of a spark
arrester; suspension travel greater than 10 inches; an engine
displacement greater than 50 cc; absence of a manufacturer warranty;
and the absence of a functional seat.
---------------------------------------------------------------------------
\51\ A spark arrester is a device located in the end of the
tailpipe that catches carbon sparks coming from the engine before
they get out of the exhaust system. This is important when a bike is
used off-highway, where hot carbon sparks falling in grassy or
wooded areas could result in fires.
\52\ Most manufacturers of motocross racing motorcycles do not
offer a warranty. Some manufacturers do, however, offer very limited
(1 to 3 months) warranties under special conditions.
---------------------------------------------------------------------------
Manufacturers must specifically request and receive an exemption
from EPA to sell off-highway motorcycles without a certificate under
the competition exemption. Vehicles not meeting the applicable criteria
listed above will be exempted only in cases where the manufacturer has
clear and convincing evidence that the vehicles for which the exemption
is being sought will be used solely for competition. Examples of this
type of evidence may be technical rationale explaining the differences
between a competition and non-competition motorcycle, marketing and
sales information indicating the intent of the motorcycle for
competition purposes, and survey data from users indicating the
competitive nature of the motorcycle.
Although there are several features that generally distinguish
competition motorcycles from recreational motorcycles, several parties
have commented that they believe motorcycles designed for competition
use are also used for recreational purposes, rather than solely for
competition. This is of particular concern because competition
motorcycles represent about 29 percent of total off-highway motorcycle
sales or approximately 43,000 units per year. However, a study on the
characterization of off-highway motorcycle usage found that there are
numerous--and increasingly popular--amateur off-highway motorcycle
competitions across the country, especially motocross.\53\ The
estimated number of off-highway motorcycle competitors is as high as
80,000. Since it is very common for competitive riders to replace their
machines every one to two years, the sale of 43,000 off-highway
competition motorcycles appears to be a reasonable number, considering
the number of competitive participants. We are therefore confident
that, although we are excluding a high percentage of off-highway
motorcycles as being competition machines, the criteria laid out above
are indicative of motorcycles used solely for competition.
---------------------------------------------------------------------------
\53\ ``Characterization of Off-Road Motorcycle Use,'' ICF
Consulting, September 2001, A-2000-1 document II-A-81.
---------------------------------------------------------------------------
However, we do recognize that it is possible that some competition
motorcycles will be used for recreational purposes. We are therefore
adopting a provision within the regulations that allows the Agency to
deny a manufacturer's claim for exemption from the standards for any
models, including models that meet the six specified criteria, where
other information is available that indicates these off-highway
motorcycle models are not used solely for competition. This same
provision allows the Agency to deny claims for exemptions in later
years even if they had been granted previously. Examples of this type
of information can be state registration data that indicate a
significant number of competition exempt models being registered to
operate on public lands. Off-highway competition motorcycles designed
for motocross competition are not typically required to be registered
with states, since most motocross competitions occur on closed-circuit
courses on private, not public land, and motocross machines lack spark
arresters which are required to operate on public land. We believe the
possibility of losing an exemption for competition motorcycles will
encourage manufacturers to take proper actions in promoting, marketing,
and guaranteeing that competition machines are sold to those
individuals who will use them solely for competition.
b. Snowmobiles and ATVs. Snowmobiles and ATVs are also used in
competition events; however, the percentage of snowmobiles or ATVs used
solely for competition is not nearly as large as that for off-highway
motorcycles. Since snowmobile and ATV competition have typically not
been as popular as off-highway motorcycle competitions, there has not
been the demand for competition machines that exists with off-highway
motorcycles. As a result, manufacturers have not manufactured and sold
directly from their dealers competition snowmobiles and ATVs like they
have off-highway motorcycles. Most snowmobiles and ATVs used in
competition events are modified recreational vehicles, rather than
stock racing machines bought directly from the dealer, as is the case
with off-highway motorcycles. As a result, there isn't the same concern
over potential misuse of competition snowmobiles and ATVs for
recreational purposes.
[[Page 68266]]
Competition snowmobiles and ATVs aren't currently sold directly at
the dealership. Therefore, manufacturers can receive a competition
exemption from EPA for snowmobiles and ATVs meeting all of the
following criteria: the vehicle or engine may not be displayed for sale
in any public dealership; sale of the vehicle must be limited to
professional racers or other qualified racers; and the vehicle must
have performance characteristics that are substantially superior to
noncompetitive models.
As with off-highway motorcycles, snowmobiles and ATVs not meeting
the applicable criteria listed above will be exempted only in cases
where the manufacturer has clear and convincing evidence that the
vehicles for which the exemption is being sought will be used solely
for competition. We are also adopting the same provision as for off-
highway motorcycles within the regulations that allows the Agency to
deny a manufacturer's claim for exemption from the standards for any
models where other information is available that indicates these
snowmobiles and ATVs models are not used solely for competition. As
with off-highway motorcycles, this same provision allows the Agency to
deny claims for exemptions in later years even if they had been granted
previously.
C. Emission Standards
1. What Are the Emission Standards and Compliance Dates?
a. Off-highway motorcycles. We are adopting HC plus NOX
and CO standards for off-highway motorcycles. We expect the largest
benefit to come from reducing HC emissions from two-stroke engines.
Two-stroke engines have very high HC emission levels. Baseline
NOX levels are relatively low for engines used in these
applications and therefore including NOX in the standard
serves only to cap NOX emissions for these engines.
Comparable CO reductions can be expected from both two-stroke and four-
stroke engines, as CO levels are similar for the two engine types. We
are also adopting averaging, banking and trading provisions for off-
highway motorcycles, as discussed below.
In the current off-highway motorcycle market, consumers can choose
between two-stroke and four-stroke models in most sizes. Each engine
type offers unique performance characteristics. Some manufacturers
specialize in two-stroke or four-stroke models, while others offer a
mix of models. The HC standard is likely to be a primary determining
factor for what technology manufacturers choose to employ to meet
emission standards overall. HC emissions can be reduced substantially
by switching from two-stroke to four-stroke engines. Four-stroke
engines are very common in off-highway motorcycle applications.
Approximately 55 percent of non-competition off-highway motorcycles are
four-stroke. Certification results from California ARB's emission-
control program for off-highway motorcycles, combined with our own
baseline emission testing, provides ample data on the emission-control
capability of four-stroke engines in off-highway motorcycles. Off-
highway motorcycles certified to California ARB standards for the 2000
model year have HC certification levels ranging from 0.4 to 1.0 g/km.
These motorcycles have engines ranging in size from 48 to 650 cc; none
of these use catalysts.
The emission standards for off-highway motorcycles take effect
beginning in the 2006 model year. We will allow a phase-in of 50-
percent implementation in the 2006 model year with full implementation
in 2007. These standards apply to testing with the highway motorcycle
Federal Test Procedure (FTP) test cycle. For HC+NOX
emissions, the standard is 2.0 g/km (3.2 g/mi). For CO emissions, the
standard is 25.0 g/km (40.5 g/mi). Both of these standards are based on
averaging with a cap on the Family Emission Limit (FEL) of 20 g/km for
HC+NOX and 50 g/km for CO. Banking and trading provisions
are also included in the program, as described in Section III.C.2.
These emission standards allow us to set near-term requirements to
introduce the low-emission technologies for substantial emission
reductions with minimal lead time. We expect manufacturers to meet
these standards using four-stroke engines with some low-level
modifications to fuel-system calibrations. These systems are similar to
those used for many years in highway motorcycle applications, but with
less overall sophistication for off-highway applications.
We received comments from several states and environmental groups
encouraging us to harmonize our off-highway motorcycle standards with
California. The comments focused on the perceived difference in
stringency between the two programs. For California, the standard is an
HC-only standard of 1.2 g/km. Our standard is a HC+NOX
standard of 2.0 g/km. We believe it is prudent to set a
HC+NOX standard in lieu of a HC-only standard since the main
emission-control strategy is expected to be the use of four-stroke
engines in lieu of two-stroke engines. Two-stroke engines emit
extremely low levels of NOX. Four-stroke engines, on the
other hand, have higher NOX emission levels, in the range of
0.3 g/km on average. This is part of the reason why we proposed a
somewhat higher numeric standard compared to California.
The California standards, which were adopted in 1994, were
stringent enough that manufacturers were unable to certify several
models of off-highway motorcycles, even some with four-stroke engine
technology. The result was a substantial shortage of products for
dealers to sell in California. The shortage led California to change
their program to allow manufacturers to sell noncompliant off-highway
motorcycles under some circumstances. As a result, approximately a
third of the off-highway motorcycles sold in California are compliant
with the standards. The uncertified models being sold in California
include both two-stroke and four-stroke machines.
EPA received comments from dealers and consumers concerned that a
similar shortage could arise nationwide if EPA adopted the California
standards. EPA shared this concern and proposed standards that were
somewhat less stringent than that of California, based on test data
from high-performance four-stroke machines. We are finalizing this
approach to ensure the four-stroke technology can be implemented
broadly across the product line in the 2006 time-frame. Although the
approach we are finalizing contains somewhat less stringent standards
than the California program, we believe it will achieve reductions
beyond that of the California program because more products will be
certified (even when the competition exemption is taken into account).
The vast majority of the HC reductions achieved by the program come
from shifting away from conventional two-stroke engines which have HC
emissions levels in the range of 35 g/km. The 2.0 g/km standard
represents about a 95-percent reduction in emissions for these
vehicles.
If we were to go beyond this level of reduction, manufacturers
would need to employ on a widespread basis additional technology that
presents significant technical issues concerning their application to
off-highway motorcycles given their extreme usage patterns and issues
such as safety, packaging, and weight. For example, technologies such
as electronic fuel injection and secondary air injection raise concerns
about their durability and reliability in the harsh operating
environments to which off-highway motorcycles are sometimes exposed.
[[Page 68267]]
The use of catalytic converters poses concerns over packaging,
durability and safety. Off-highway motorcycles are very light and
narrow. These attributes are necessary for operating through tight
forest trails and other harsh conditions. This leaves little room for
packaging a catalyst so that it won't be damaged from engine vibration,
shock resulting from jumps and hopping logs, and falling over and
hitting objects, such as trees and rocks. These technologies may become
compatible for off-highway motorcycles in the future, but we do not
believe that it is appropriate to promulgate emission standards based
on these technologies at this time, given the technical problems
currently associated with their use. Four-stroke engine technology has
advanced considerably since the California regulations went into
effect. Manufacturers are now capable of offering four-stroke engines
that provide excellent performance. This performance can be achieved
only as long as manufacturers are allowed to operate four-stroke
engines with a slightly rich air and fuel mixture, which can result in
somewhat higher HC and CO emissions. Although the standards we are
setting are higher than those in California, we believe they will
require four-stroke engines that are well calibrated for emissions
control without significantly sacrificing performance. For these
reasons, we believe the standards we are establishing are appropriate.
As discussed above in Section III.B.5, the Clean Air Act requires
us to exempt from emission standards off-highway motorcycles used for
competition. We expect several competition two-stroke off-highway
motorcycle models to continue to be available. We are concerned that
setting standards as stringent as California's would result in a
performance penalty for some four-stroke engines that would be
unacceptable to the consumers. This could encourage consumers who want
performance-oriented off-highway motorcycles to purchase competition
vehicles (and use them recreationally) in lieu of purchasing compliant
machines that don't provide the desired performance. We believe that
our emission standards will allow the continued advancement of four-
stroke technology and properly considers available emission-control
technology while taking vehicle performance into consideration and
avoiding significant adverse impacts on performance.
As proposed, we are also finalizing an option allowing off-highway
motorcycles with an engine displacement of 50 cc or less to be
certified using the Small SI emission standards for non-handheld Class
I engines. These youth-oriented models may not be able to operate over
the FTP due to the higher speeds of the test cycle. We did not receive
comment on this provision.
Optional Standards
During the comment period, we received several comments expressing
concern that our proposed standard of 2.0 g/km HC+NOX for
off-highway motorcycles would effectively prohibit the use of two-
stroke engines in non-competition applications. These engines currently
have typical HC+NOX levels of about 35 g/km. The commenters
argued that two-stroke engines possess several unique attributes, such
as high power and light weight, that make two-stroke powered off-
highway motorcycles more desirable to some operators, especially
smaller, lighter riders, than heavier four-stroke powered off-highway
motorcycles.
We also received comments from several states and environmental
organizations expressing strong concern over the number of competition
off-highway motorcycles that would be exempt from our regulations as a
result of our competition exemption. They felt that people purchasing
exempt competition motorcycles would use them for recreational purposes
instead of solely for competition.
One manufacturer indicated that they were planning on building
high-performance off-highway motorcycles equipped with direct fuel-
injection two-stroke engines that would potentially be capable of
meeting a HC+NOX standard of 4.0 g/km. To enable use of this
technology, they suggested that we should adopt a standard of 4.0 g/km
instead of the proposed standard of 2.0 g/km. The commenter believes
that direct injection could be used to make clean competition machines
and also argued that the technology is robust and not as susceptible to
user modifications as other technologies such as catalysts. The
commenter wanted an opportunity to develop and certify their product
because it perceives a benefit to the purchaser not only in performance
but also in the ability for the owner to resell the competition vehicle
into the secondary market without concerns about potential misuse. In
addition, the owner would be able to use the vehicle both for
competition and recreation.
It is clear that if manufacturers were able to certify and bring to
market clean competition machines as described by the commenter,
significant reductions in emissions would be gained over conventional
two-stroke technology. Some competition models we tested had baseline
HC and CO emissions in excess of 50 g/km and 40 g/km, respectively. We
believe it is appropriate to provide an avenue for the development and
voluntary certification of clean competition motorcycles. Therefore, we
are finalizing an optional set of standards for off-highway motorcycles
of 4.0 g/km HC+NOX and 35.0 g/km CO. For manufacturers to
utilize this option, however, they must certify all of their models,
including their competition models, to the optional standards. To
qualify for this option, a manufacturer must show that ten percent or
more of their sales would otherwise meet the competition definition.
The optional standard was derived from the fact that non-
competition four-stroke engines can meet a 2.0 g/km level and
competition two-stroke machines with advanced direct fuel-injection
technology could meet a 8.0 g/km level. Since approximately one-third
of the total off-highway motorcycle fleet are competition machines and
the other two-thirds would be non-competition four-stroke recreational
machines, the weighting of the 2.0 g/km level by two-thirds and the 8.0
g/km level by one-third results in a weighted standard of 4.0 g/km.
This presumes that emissions from four-stroke engines will not increase
under this option and that non-competition engines will be almost
exclusively four-stroke engines. These assumptions are discussed below.
The significant reductions in otherwise unregulated competition engines
means that this option should produce even greater overall reductions
than the base 2.0 g/km standard. We recognize that for some
manufacturers this program will increase opportunities to make a
limited number of non-competition recreational two-stroke machines;
however, we believe that the number of two-stroke non-competition
engines developed under this program will be limited by the fact that
the required technology (direct fuel-injection) would be too expensive
and complex for the recreational motorcycle market. The majority of
non-competition recreational off-highway motorcycles that use two-
stroke engines are entry-level and youth motorcycles, where cost and
simplicity are important factors. There is also the fact that for every
two stroke non-competition engine manufactured under this program, a
manufacturer must make one less competition engine or must make more
four-stroke engines. Further, we believe that any increase in the
number of non-competition two-stroke engines is justified given the
fact that this program will overall bring levels from off-highway
engines down
[[Page 68268]]
considerably and the fact that the technology needed to reduce
emissions from competition machines will only be made available and
used if, under this optional approach, manufacturers have an incentive
to use the technologies.
One major incentive in using this approach is the fact that once
these machines are certified, a consumer will be able to use these
machines legally for non-competition uses, which increases the value of
the competition machines. This approach thus will also reduce the
incentive for manufacturers to manufacturer all of their two-stroke
machines as competition machines to avoid regulation, and thus reduce
the incentive for users to circumvent the regulations. This may mean
that any increase in two-stroke non-competition engines under this
approach would not lead to an increase in total two-stroke sales,
because manufacturers will not have an incentive to increase the number
of two-stroke competition vehicles to avoid regulation.
We believe this approach is responsive to all of the above
comments. It directly addresses the concerns of the manufacturer
developing the new competition motorcycle and also helps address the
concerns of users, states, and environmental groups. The successful
development and certification of clean competition models increases the
choices for consumers in the marketplace. Offered the option of a
certified high-performance two-stroke off-highway motorcycle that can
be used both for competition and recreation, consumers may not feel the
need to purchase exempt competition motorcycles. This option has the
potential to significantly decrease the number of conventional two-
stroke competition machines sold under the competition exemption and is
likely to decrease the potential for misuse of competition machines.
Conventional competition two-stroke motorcycles generate extremely high
levels of HC emissions, as noted above. For every conventional two-
stroke competition machine replaced by a certified competition machine,
HC emissions would be reduced by 80 percent, or more.
While the 4.0 g/km standard is higher than the 2.0 g/km standard
contained in the base program, we do not expect any loss in emissions
reductions from four-stroke models. We continue to believe most off-
highway motorcycles will continue to be powered by four-stroke engines.
Most non-competition off-highway motorcycles are already four-stroke
motorcycles, and the trend towards four-stroke is continuing even in
the absence of these regulations. We are convinced that there will be
no backsliding of emissions control for motorcycles using four-stroke
engines, because the dirtiest of the four-stroke models tend to be
competition machines, and our emissions testing indicates that
competition four-stroke off-highway motorcycles have HC+NOX
emission levels below 2.0 g/km. Since these motorcycles are optimized
for power and racing conditions, there is no incentive for
manufacturers to increase HC+NOX emissions from their
current levels. In fact, increasing the emission levels would mean
increasing the air-to-fuel mixture, which would tend to reduce the
engines performance.
As with the primary program, these optional standards would take
effect in 2006 with 50-percent implementation and full implementation
in 2007 and manufacturers could switch between the options from model
year to model year. The HC+NOX standard can be met through
averaging with some families certified above the standards and some
below. If averaging is used, the FEL cap would be 8.0 g/km.
We are retaining the averaging approach for this option because it
may be a critical flexibility for manufacturers pursuing clean
competition products. The commenter based its recommendation for a 4.0
g/km standard on their projections for a single prototype model
equipped with a medium sized engine. This engine is in the early stages
of development and there is some uncertainty as to what emissions level
the final product can achieve. Also, manufacturers may want to apply
their approach to other engines that may not be able to achieve this
same level of control. Manufacturers could find that they can produce
competition products that are very clean relative to the baseline but
with higher emissions than 4.0 g/km. For example, larger engine sizes
could have emissions levels somewhat higher than the 4.0 g/km suggested
by the commenter. We are not satisfied at this time that two-stroke
off-highway motorcycles, particularly those used in competition could
meet the 4.0 g/km standard, especially considering the special
performance needs of competition motorcycles. Therefore, rather than
keeping a 2.0 g/km standard for four-stroke engines and having a
standard higher than 4.0 g/km for two-stroke engines (a standard as
high as 8.0 g/km might be appropriate), we are using a 4.0 g/km
standard that permits averaging. Averaging provides flexibility for
manufacturers to bring cleaner two-stroke, particularly cleaner
competition two-stroke, engines to market without creating a
disincentive to building four-stroke engines. One way of taking
advantage of the averaging program in this way would be for a
manufacturer to maximize its sales of four-stroke models as part of its
sales mix, and average the emissions from these engines against the
higher emissions of the two-stroke competition engines which still
would need to be much cleaner than if they were unregulated. This
approach therefore requires the substantial use of cleaner four-stroke
technologies while at the same time encouraging manufacturers to
substantially reduce emissions from motorcycles that would otherwise be
unregulated competition motorcycles. We have capped the emissions
levels at 8.0 g/km HC+NOX because we want to ensure that
products certified under this option provide large emissions reductions
compared to baseline levels and that the option provides environmental
benefits in all cases. Competition motorcycles certified to the 8.0 g/
km level would continue to provide over a 75-percent reduction in HC
emissions over baseline levels.
One of the challenges facing manufacturers selecting this option is
the potentially high CO emissions from competition machines. We tested
competition models and found CO emissions to be in the range 25 to 50
g/km. Although this option contains a somewhat higher CO standard (35
g/km compared to 25 g/km) than the base program, manufacturers are
still expected to need to control CO emissions through tight engine
calibrations. We are not including averaging for the less stringent CO
standard. As noted by the manufacturer supporting the 4.0 g/km option,
direct injection technology is likely to reduce CO from two-stroke
engines. We believe that through proper calibration, the 35 g/km
standard will be achievable and will not significantly impede
manufacturers in selecting this option.
b. ATVs. We are adopting HC plus NOX and CO standards
for ATVs. We expect the largest benefit to come from reducing HC
emissions from two-stroke engines. Two-stroke engines have very high HC
emission levels. Baseline NOX levels are relatively low for
engines used in these applications and therefore including
NOX in these standards serves only to cap NOX
emissions for these engines. Comparable CO reductions can be expected
from both two-stroke and four-stroke engines, as CO levels are similar
for the two engine types. We are also adopting averaging, banking and
trading provisions for ATVs, as discussed below.
In the current ATV market, consumers can choose between two-stroke
and four-stroke models, although the
[[Page 68269]]
majority, approximately eighty-percent of sales, are four-stroke. Each
engine type offers unique performance characteristics. Some
manufacturers specialize in two-stroke or four-stroke models, but most
manufacturers offer a mix of models. The HC standard is likely to be a
primary determining factor for which technology manufacturers choose to
employ to meet emission standards overall. HC emissions can be reduced
substantially by switching from two-stroke to four-stroke engines.
Certification results from California ARB's emission-control program
for ATVs, combined with our own baseline emission testing, provides
ample data on the emission-control capability of four-stroke engines in
ATVs.
In the proposal we included two phases of ATV standards. The first
phase of standards, 2.0 g/km HC+NOX and 25 g/km CO, was
proposed to be phased in at 50 percent of production in 2006 with the
remainder phased-in for 2007. We proposed a second set of standards
that included a more stringent 1.0 g/km HC+NOX standard with
no change to the CO standards. It was to be met in 2009/2010 using the
same 50-percent and 100-percent phase-in scheme as Phase 1. We proposed
that both phases of HC+NOX standards could be met through
averaging.
We received comments from several environmental groups stating that
we should harmonize our Phase 1 standards with the California FTP-based
standards. Manufacturers did not comment on the level of our proposed
Phase 1 HC+NOX standards. However, in a letter sent to the
Agency in August 6, 2001, just before we published the proposal, the
Motorcycle Industry Council stated that the most cost-effective
approach to setting standards for ATVs would be to adopt the California
HC standards of 1.2 g/km. They did comment on the fact that almost all
of the CO nonattainment areas identified in the Draft Regulatory
Support Document are now in compliance and that ATV activity is
typically so far removed from congested urban areas, that we should
delete the proposed CO standard.\54\ Manufacturers stated generally
that CO standards will make it more difficult to meet the
HC+NOX standards but did not provide additional specific
comments on the feasibility or costs of the CO level proposed. In
subsequent meetings with manufacturers, they suggested that if we were
not going to delete the CO standard, it should be set sufficiently high
so that it would not be an impediment to meeting the HC+NOX
standard. They suggested a level of 50.0 g/km.
---------------------------------------------------------------------------
\54\ We respond to these comments in Section II of the Summary
and Analysis of Comments.
---------------------------------------------------------------------------
We have decided to finalize only one set of HC+NOX
emission standards for the 2006 model year that are essentially
equivalent to the California standard. The emission standards for ATVs
take effect beginning in the 2006 model year. We will allow a phase-in
of 50-percent implementation in the 2006 model year with full
implementation in 2007. These standards apply to testing with the
highway motorcycle Class I FTP test cycle. For HC+NOX
emissions, the standard is 1.5 g/km (2.4 g/mi). The California program
has a HC-only standard of 1.2 g/km. We have made the standard 1.5 g/km
to account for NOX emissions. For CO emissions, we agree
with manufacturers that CO standards can make it more difficult to meet
the HC+NOX standard. Based on our emission test data, we
feel that a standard of 35.0 g/km (56.4 g/mi) is more appropriate than
the 25.0 g/km standard we proposed or the 50.0 g/km standard suggested
by the manufacturers. A standard of 35.0 g/km will still result in an
overall reduction in CO emissions from high emitting ATVs, but will
also allow manufacturers to balance CO control with the need to meet
stringent NOX levels. The HC+NOX standard may be
met through averaging. Banking and trading provisions for
HC+NOX are also being included in the program, as discussed
in C.2., below.
Our decision to finalize a 1.5 g/km value rather than the 2.0 g/km
value is consistent with the manufacturers technical capability in the
2006/2007 time-frame. The 1.5 g/km HC+NOX and 35 g/km CO
standards require the use of engine technology changes and add-on
devices such as secondary air systems, which are clearly available for
ATV application in this time frame. We proposed a 1.0 g/km
HC+NOX standard for a 2009/2010 phase-in which could require
use of catalytic converter technology in many models of ATVs. As
discussed below, we are not finalizing that proposal now, and thus find
it appropriate to finalize more stringent Phase 1 standards which are
technologically feasible and otherwise consistent with statutory
criteria related to cost, safety, noise, and energy considerations.
Aligning our emission standards with those currently in place in
California allows us to set requirements to introduce the low-emission
technologies for substantial emission reductions with reasonable lead
time and will for the most part allow manufacturers to sell one model
in all fifty states. This ``harmonization'' between federal and
California requirements is valued by industry because it allows the
development and production of one emission-control technology per
model/family. However, in a few cases, we expect emissions reductions
under the EPA program that go beyond that of the California program
because California allows the sale of uncertified ATVs, including two-
stroke models, under their red sticker provisions. With the exception
of competition exempt ATVs, all ATV models subject to the EPA program
will need to be certified. We expect manufacturers to meet these
standards using four-stroke engines with some modifications to fuel-
system calibrations and some limited use of secondary air systems.
These systems are similar to those used for many years in highway
applications, but will likely require lesser sophistication than used
in highway motorcycle applications.
In addition to being consistent with the California standards, we
feel the 1.5 g/km HC+NOX standard is more appropriate than
the proposed 2.0 g/km standard because our testing has shown that
emission levels from four-stroke ATVs can vary considerably. We stated
in the proposed rule that a standard of 2.0 g/km HC+NOX
would be a four-stroke enforcing standard, which would most likely
result in the elimination of any two-stroke engines, but not
necessarily require any additional control from the four-stroke
engines. As stated above, a standard of 1.5 g/km HC+NOX will
require the use of engine technology changes and add-on devices such as
secondary air systems, which are clearly available for ATV application
in this time frame.
At this point, we do not believe it is appropriate to promulgate
Phase 2 standards. In the proposal, we projected significant use of
secondary air systems and catalysts for meeting the Phase 2 standards.
Since that time, we have been conducting testing on ATVs with the type
of catalysts and secondary air systems we envisioned for the Phase 2
standards to demonstrate feasibility. However, the testing we have done
to date has not been sufficient to reach an affirmative conclusion on
the feasibility of the Phase 2 standards. Testing with secondary air
systems and catalysts have not shown consistent results and we have had
only partial success in demonstrating the feasibility of the proposed
Phase 2 standards using these technologies. In testing on a utility-
type ATV, these technologies have provided only small emissions
reductions.\55\ The
[[Page 68270]]
results of our preliminary testing are discussed further in Section
III.F and in the Final Regulatory Support Document. It is unclear if
the level of technology we projected in the proposal would be
sufficient to meet the Phase 2 standards. We have not done enough
research or testing on other potential technologies, such as electronic
or direct fuel injection, to finalize a decision based on these
technologies. We plan to continue to evaluate the technologies that
would be needed to meet the Phase 2 levels and determine if those
levels can be met with the level of technology we projected in the
proposal or with other technology. We also received comments that we
underestimated costs for Phase 2 and we will continue to evaluate costs
as well.
---------------------------------------------------------------------------
\55\ Utility-type ATVs, it should be noted, are not the same as
utility vehicles. Utility vehicles are not considered ATVs due to
fundamental differences in the vehicle characteristics. Most utility
vehicles are currently regulated by the Small SI program, with a
small subset of utility vehicles required by the Final Rule to meet
ATV standards. See section III.B.3. above, for a complete discussion
of utility vehicles. When we say utility-type ATV, we are referring
to ATVs that have features that are work related such as cargo
racks. These ATVs are often somewhat larger and bulkier than sport
models and may have transmissions geared more for work related tasks
rather than for high performance. However, they have ATV features
such as four low pressure tires, a seat designed to be straddled by
the operator, handlebars for steering controls, and are intended for
use by a single operator. These vehicle must meet ATV requirements.
---------------------------------------------------------------------------
In addition, we received comments that the emissions inventories we
projected for ATVs were too large, and that if we adjusted them
appropriately, we would see that Phase 2 was not needed. This is
provided in detail in the public docket.\56\ We have studied and
evaluated in-depth the new and additional information provided by the
commenters after we published the proposal. As is shown in our revised
analysis, the emissions inventory projections for ATVs have been
reduced by more than 75 percent in response to the significant new
information we received after publishing the proposal. Our analysis of
the appropriate standards for 2006/2007 described above was made using
this new information, and future analysis of Phase 2 standards would
also use these revised inventory numbers. However, it is important to
note that the revised inventories still show that these vehicles
contribute to nonattainment.
---------------------------------------------------------------------------
\56\ Comments of the Motorcycle Industry Council, Inc., and the
Specialty Vehicle Institute of America on the Notice of Proposed
Rulemaking to Establish Mandatory Emission Standards for Nonroad
Large Spark-Ignition Engines and Recreational Engines (Marine and
Land-Based), Air Docket A-2000-01, IV-D-214.
---------------------------------------------------------------------------
Engine-based Standards
California allows ATVs to be optionally tested using the California
ARB utility engine test cycle (SAE J1088) and procedures. In
California, manufacturers using the J1088 engine test cycle option must
meet the California Small Off-Road Engine emission standards. Some
manufacturers do not have chassis testing facilities and at the time
California finalized its program were concerned about the cost of doing
FTP testing for California-only requirements. To use this option,
manufacturers were required by California to submit some emission data
from the various modes of the J1088 test cycles to show that emissions
from these modes were comparable to FTP emissions. Although a good
correlation was not found between the two test cycles, California
allowed this option because the goal of their program was to encourage
four-stroke engine technology in ATVs.
As described above, we are finalizing standards based on vehicle
testing over the FTP that are essentially harmonized with the
California FTP standards. We did not propose a permanent option of
engine testing using J1088 due to strong concerns that the test cycle
misses substantial portions of ATV operation because it contains test
points at only one engine speed. We understand that vehicle testing
would be a significant change for manufacturers who currently conduct
emissions testing on the engine rather than the vehicle for California.
Due to the costs and lead-time requirements associated with switching
to vehicle-based testing, we proposed a transitional program to allow
the J1088 option for models years 2006 through 2008. To facilitate the
phase-in of ATV standards, we proposed to allow manufacturers to
optionally certify ATVs using the California utility cycle and
standards, shown in Table III.C-1, instead of the FTP standards.
Table III.C-1.--California Utility Engine Emission Standards
------------------------------------------------------------------------
Engine displacement HC+NOX CO
------------------------------------------------------------------------
Less than 225 cc............. 12.0 g/hp-hr.... 300 g/hp-hr
(16.1 g/kW-hr)... (400 g/kW-hr)
Greater than 225 cc.......... 10.0 g/hp-hr..... 300 g/hp-hr
(13.4 g/kW-hr)... (400 g/kW-hr)
------------------------------------------------------------------------
We are finalizing this approach, but will eliminate the J1088
option (including both the test cycle and the utility engine emission
standards) for certification in model year 2009. The last model year to
use the J1088 cycle and emission standards is 2008. We received
comments that the FTP is also not representative of ATV operation and
that the J1088 option should remain available until a new test cycle
and accompanying standards can be developed and made available to
manufacturers. Although it may not be completely representative of ATV
operation, we believe the FTP to be greatly superior to the J1088 test
cycle because the cycle is transient, emissions are measured at a
variety of speeds and it is more likely to result in robust emission-
control designs that reduce emissions in-use. We continue to be very
concerned that the vast majority of ATV operation is missed with the
J1088 test because the engine is tested at only one engine speed. ATV
operation is inherently transient in nature because the user controls
the throttle position to vary vehicle speed. We believe the J1088 test
is not sufficient to ensure robust emissions control development and
use for ATVs. Given the choice of available test procedures for the
long-term, we could not justify retaining the J1088 option.
For small displacement ATVs of 70 cc or less, we proposed that they
would have the permanent option to certify to the proposed FTP-based
ATV standards discussed above or meet the Phase 1 Small SI emission
standards for non-handheld Class 1 engines. These standards are 16.1 g/
kW-hr HC+NOX and 610 g/kW-hr CO. Manufacturers argued that
ATVs with engine displacements between 70 cc and 99 cc also should be
allowed to certify to the Small SI standards, since the differences
between a 70 cc and 99 cc engine is very small and the ATVs equipped
with 99
[[Page 68271]]
cc engines face the same obstacles with the FTP test cycle as the 70 cc
and below ATVs. They also argued that the Phase 1 Small SI standards
are too stringent for these engines and recommended that EPA adopt the
Phase 2 standards for Class 1B engines of 40 g/kW-hr for
HC+NOX and 610 g/kW-hr for CO.
We recognize that the vast majority of engine families, including
4-stroke engines, below 100 cc are not certified to the California
standards, which is an indication to us that the standards proposed may
not be feasible for most engines in this size range given the lead time
provided. However, manufacturers did not provide supporting data and we
do not have data to confirm that the level recommended by the
manufacturers would result in an appropriate level of control. We
examined the 2002 model year certification data for non-handheld Small
SI engines certified to the Phase 2 Class I-A and I-B engine standards
(engines below 100 cc). We found that the five engine families
certified to these standards had average emissions for
HC+NOX of about 25 g/kW-hr. All of these engine families had
CO emissions below 500 g/kW-hr and well below the 610 g/kW-hr level
recommended by manufacturers. We believe these levels are more
representative of the levels that can be achieved with the lead time
provided through the use of 4-stroke engines than the standards
recommended by the manufacturers. Therefore, we are finalizing a 25.0
g/kW-hr HC+NOX standard and a 500 g/kW-hr CO standard for
ATVs with engine displacements of 99 cc or less. These standards will
be optional to the FTP-based standards and, unlike the J-1088 standards
option for larger displacement engines, the option will not expire. We
are retaining averaging for the HC+NOX standard but do not
believe averaging would be appropriate for the CO standard. This is
consistent with the approach outlined above for J-1088 standards for
engines above 100 cc.
The ATV standards are phased in at 50% of a manufacturer's
production in 2006 and 100% in 2007. This phase-in applies to a
manufacturer's overall ATV production regardless engine size or which
option a manufacturer chooses for standards for particular models.
New Test Procedure for ATVs
We are comfortable with retaining the FTP as the basis of the long-
term ATV program. However, EPA understands the manufacturers' concerns
regarding the additional facility costs associated with FTP testing for
ATVs. We also recognize that this approach is a significant deviation
from their current practice in the California program. Throughout the
development of the final rule, we have met with manufacturers and the
State of California and have discussed the possibility of developing a
new test cycle for ATVs. We intend to work further with all interested
parties to determine whether a new test cycle and accompanying
standards is appropriate. The standards, if developed for the new test
cycle, would be of equivalent stringency to the FTP standards discussed
above. If we do propose a new test cycle and accompanying standards for
ATVs, it is likely that we would do so in concert with a decision on
whether a second phase of standards is appropriate for ATVs. We are now
developing a Memorandum of Understanding with manufacturers which
describes in detail the steps that will be taken in furtherance of this
task.\57\ Other interested parties including the state of California
will also be invited to participate in this process.
---------------------------------------------------------------------------
\57\ See item IV-G-114, docket A-2000-01.
---------------------------------------------------------------------------
By finalizing the temporary availability of J1088, we are providing
time to develop, and if appropriate, finalize and implement an
alternative to the FTP that meets both the needs of the Agency,
manufacturers and other parties. This allows for our program to remain
harmonized with California during the transition to the new test
procedure. However, we do not support allowing the use of J1088 for a
period any longer than necessary to make this transition. We expect
that developing a new test cycle will be relatively straightforward and
that the MOU process cited above will provide a road map of how we will
proceed. We expect to initiate this effort next year and conclude the
work on the new test cycle in enough time to promulgate it through
rulemaking and to provide industry adequate lead time to implement it
in an orderly manner (nominally three years lead time). If we encounter
unforeseen and unavoidable delays or complications in this process, we
will consider extending the J1088 temporarily as part of our process of
adopting changes to the ATV test cycle through rulemaking. We would
expect such an extension to be at most for one model year.
c. Snowmobiles. We are adopting CO and HC emission standards for
snowmobiles, effective in three phases, as discussed below. As
discussed below, we are also adopting an emissions averaging banking
and trading program for snowmobiles which includes provisions for the
early generation of credits prior to the effective date of the
standards. We are not adopting PM standards for snowmobiles at this
time, because limits on HC emissions will serve to simultaneously
reduce PM and because there are significant complications in accurately
measuring PM that make requiring PM standards difficult in this time
frame. Finally, we are not adopting limits for NOX for the
first two phases of standards, but manufacturers are required to
measure NOX emissions and report them in the application for
certification. However, we have included NOX in the Phase 3
standards to effectively cap NOX emissions from snowmobiles.
The three phases of standards we are adopting will require
progressively broader application of advanced technologies such as
direct injection two-stroke technology, and four stroke engines. Only
about two percent of current snowmobile production utilizes these
advanced technologies. We expect that about seven percent of new
snowmobiles will have them by 2005. With the Phase 1 standards we
expect that ten percent of snowmobiles will require advanced
technologies (in addition to less advanced emissions controls on most
other snowmobiles). We project that the Phase 2 and Phase 3 standards
will require the application of advanced technology on 50 and 70
percent of new snowmobiles, respectively.
Phase 1 Standards
We are adopting Phase 1 standards largely as proposed for
snowmobiles to take effect for all models starting in the 2006 model
year. However, given that the manufacturers will effectively have only
three years to design and certify snowmobiles prior to the 2006 model
year, as well as the fact that snowmobiles are currently unregulated,
we believe that requiring 100 percent of models to certify in 2006 is
not reasonable. Thus, we are including a phase in of the Phase 1
standards with 50 percent of sales required to comply with the 30
percent reduction standards in 2006 and 100 percent compliance required
in 2007. The standards of 275 g/kW-hr (205 g/hp-hr) for CO and 100 g/
kW-hr (75 g/hp-hr) for HC are to be met on average by each
manufacturer. As described in the proposal, these standards represent a
30-percent reduction from the baseline CO and HC emission rates for
uncontrolled snowmobiles. We expect manufacturers to meet these
standards using a variety of technologies and strategies across their
product lines. For the reasons
[[Page 68272]]
described below, we believe these are the most stringent standards
feasible beginning in the 2006 model year.
Snowmobiles pose some unique challenges for implementing emission-
control technologies and strategies. Snowmobiles are very sensitive to
weight, power, and packaging constraints. Current snowmobile designs
have very high power-to-weight ratios, to address performance
considerations. The desire for low weight has been stated to be a
concern, since weight (and weight distribution) affects handling and
operators occasionally have to drag their sleds out of deep snow. This
has especially been mentioned as a concern in the context of four-
stroke engines given that they are heavier than their two-stroke
counterparts of similar power. However, four-stroke engines have
significantly better fuel economy than two-stroke engines, and for
identical fuel tank sizes, would have significantly greater range. This
of course would be a positive attribute. The size of a fuel tank on a
four-stroke powered snowmobile could be reduced to provide similar
range to that of a similarly powered two-stroke snowmobile, resulting
in offsetting weight savings from both the smaller fuel tank and less
fuel on board. However, this could still represent a change in the
distribution of weight compared to current sleds.
The approach used to control emissions in compliance with the Phase
1 standards will vary according to a given manufacturers product line,
technological capability, long term plans, and other factors. However,
we expect all manufacturers to pursue a mix of technologies. Some
manufacturers may focus more on clean carburetion and associated engine
modifications and apply those widely across their entire product line
with more limited implementation of advanced technology such as four-
stroke and semi direct injection engines. Others may choose to be more
aggressive in applying advanced technologies in their more expensive,
high-performance sleds and be less aggressive in pursuing emission
reductions from their lower-priced offerings to optimize the fit of
different technologies (and their associated costs) to the various
product offerings in the near term. As can be seen on their
websites\58\, all large manufacturers now have limited product
offerings of advanced emissions technology snowmobiles. Snowmobiles
must, on average and according to the phase in schedule, meet the first
phase of emission standards beginning with the 2006 model year. Given
the relative inexperience this industry has with designing effective
snowmobile engines with advanced emissions controls and in certifying
to EPA requirements, it is unlikely that any manufacturer could market
enough of these advanced snowmobiles for model year 2006 to enable it
to meet significantly more stringent standards. Due to the unique
performance requirements for snowmobiles and the relatively short lead
time to modify current engines or design new products, we believe our
2006/2007 standards will be technologically challenging for
manufacturers and will result in cleaner snowmobiles.
---------------------------------------------------------------------------
\58\ http://www.arcticcat.com, http://www.polarisindustries.com,
http://www.skidoo.com, and http://www.yamaha-motor.com.
---------------------------------------------------------------------------
Phase 2 and Phase 3 Standards
We believe the two most viable advanced technologies for use in
snowmobiles are two-stroke direct (or semi-direct) injection technology
and four-stroke engines. All four major snowmobile manufacturers either
currently offer or are planning to offer in the next year or two one or
more of these technologies on a limited number of snowmobile models.
With sufficient resources and lead time for manufacturers, we believe
it would be technologically possible to eventually apply such advanced
technology broadly across most or all of the snowmobile fleet.
Manufacturers have indicated that with enough investment and
sufficient time to design and implement direct injection technology for
snowmobile use, two-stroke engines equipped with direct fuel injection
systems can reduce HC emissions by 70 to 75 percent and reduce CO
emissions by 50 to 70 percent. These projections are based largely on
laboratory prototypes and generally do not account for in-use
deterioration or the need for production compliance margins in the
ultimate certification levels. Certification results for 2002 model
year outboard engines and personal water craft support these
projections.\59\
---------------------------------------------------------------------------
\59\ See the snowmobile feasibility discussion in the Final
Regulatory Support Document.
---------------------------------------------------------------------------
In addition to the direct injection two-stroke, a few four-stroke
models are currently available, and more are expected to be introduced
in the next few years. Based on testing of prototypes and other low-
hour engines it appears that advanced four-stroke snowmobiles are
capable of HC reductions ranging from 70 to 95 percent relative to
current technology two-stroke snowmobile engines. However, CO
reductions from four stroke engines vary quite a bit. For four-stroke
engines used in low-power applications, CO reductions of 50 to 80
percent from baseline levels have been reported. However, the majority
of the snowmobile market is for higher-powered performance machines,
and CO reductions from higher powered four stroke engines are lower
than those from low powered four strokes, with expected reductions of
20 to 50 percent from baseline levels. As discussed further in the RSD
and Summary and Analysis of Comments document, we expect that many of
the four-stroke snowmobile models offered in the future will not be
current two-stroke models which have been modified to utilize a four-
stroke engine, but rather new models designed specifically to take
advantage of the unique characteristics of four-stroke engines. Thus,
we expect that the lead time associated with the conversion to four-
stroke engines and optimized sleds is even longer than that needed for
conversion to direct injection two-stroke technology.
It is not obvious to us that either of these advanced technologies
is better than the other or more suited to broad application in the
snowmobile market. Each has its strong points regarding emissions
performance, power, noise, cost, etc. For example, two-stroke engines
equipped with direct fuel injection have the potential to have greater
CO emission reductions than a comparably powered four-stroke engine,
although they would have less HC reductions. For those applications
where a light, powerful, compact engine is desired, a direct injection
two-stroke engine may be preferred. However, for applications where
pure power and speed is desired, a high-performance four-stroke engine
may be preferred. Given the broad range of snowmobile model designs and
applications it is apparent that one of these technologies could be
preferable to the other in some situations. Further, given the broad
range of snowmobile types offered, a mix of advanced technologies would
provide the best opportunity for substantial average emission
reductions while still maintaining customer satisfaction across the
entire range of snowmobile types. Thus, we believe it is most
appropriate to set emission standards for snowmobiles that are not
based entirely on the use of either direct injection two-stroke
technology or four-stroke engines, but rather a mix of the
[[Page 68273]]
two, along with some other technologies in certain applications.
It is our belief that with sufficient resources and lead time,
manufacturers can successfully implement technologies such as two-
stroke direct injection and four-stroke engines in many models in their
respective snowmobile fleets. The question at hand is how broadly this
technology can be practically applied across the snowmobile fleet in
the near term, taking into account factors such as the number of engine
and snowmobile models currently available, and the capacity of the
industry to perform the research and development efforts required to
optimally apply advanced technology to each of these models.
Currently there are only four major snowmobile manufacturers, and
each has different technological capabilities. Of these four, only two
currently manufacturer all of their own engines, one has limited in-
house engine manufacturing operations, the other has none. Beyond this,
there are only two advanced technologies (direct injection two-stroke,
and four stroke) that at this time appear to be feasible to provide
significant reductions in snowmobile emissions. Further, given the
small volume of snowmobile sales compared to other vehicles and
equipment which use similar sized engines, these manufacturers may have
difficulty in working with their engine suppliers to develop and
optimize four-stroke or direct injection two-stroke technology quickly.
Clearly, the nature of the relationship between these snowmobile
manufacturers and their suppliers would result in a less efficient use
of available lead time as compared to the manufacturers that have both
technology and engine manufacturing available in-house. Thus, there is
varying capability within the snowmobile industry to develop and
implement advanced technology in the next five to ten years.
The amount of engine redesign or development work is another
factor. While one snowmobile manufacturer currently offers four
different engine models, the other three, including the two that do not
manufacture their own engines, currently offer eight to twelve engine
models each. Additionally, each of these engine models typically goes
into more than one type of snowmobile. There are a variety of basic
snowmobile types specifically designed for a variety of riding styles
and terrains including high-performance trail riding, high-performance
off-trail riding (including designs specifically for deep snow),
mountain riding, touring (two person snowmobiles designed for use on
groomed trails), and entry level snowmobiles (lower-powered and lower
priced snowmobiles which utilize simpler technology and are
specifically designed to appeal to first time buyers). Some snowmobile
manufacturers also offer snowmobile models specifically for youth, and
utility models for work in cold climates or to facilitate winter sports
such as hauling winter camping gear, or hunting and fishing equipment.
It is not surprising that some of these snowmobile models are much more
popular than others. Thus, there can be quite a difference in the
production volumes of the different snowmobile types, with performance
models typically having large sales volumes, and more unique models
such as utility and youth models selling far fewer units.
Considering the number of snowmobile types, and the fact that each
engine model is typically used in several different snowmobile models,
each manufacturer has potentially dozens of different engine/snowmobile
combinations that it offers. An analysis of the manufacturers current
product offerings shows that while one manufacturer has only about
twelve unique engine/snowmobile model combinations, the other three
offer significantly more--from around 30 to over 50. Each of these
different snowmobile models is designed with specific power needs in
mind, with the engine and clutching specifically suited for the
application style for which the snowmobile was intended. This means
that a given engine model may require slightly different calibrations
for each different snowmobile model in which it is used. While the
advanced technologies are known, they are not ``one size fits all''
technologies. These technologies need to be optimized not only for the
specific engine model, but in some cases for the snowmobile the engine
will be used in as well, as just described.
For all of the reasons just discussed, we believe that it is
necessary to allow two additional years of lead time for compliance
with the proposed Phase 2 standards, and are therefore adopting the
ultimate phase of snowmobile standards effective for the 2012 model
year rather than the 2010 model year as proposed. However, we expect
that between the 2006 and 2012 model years there can and will be
substantial development and application of advanced technologies on
snowmobiles beyond that required in compliance with the Phase 1
standards. We believe that it is important to capture the emission
benefits that these advances present, and are therefore adopting a new
set of Phase 2 standards, effective with the 2010 model year, which
will require 50 percent HC reductions and 30 percent CO reductions from
average baseline levels. The Phase 2 standards are 275 g/kW-hr (205 g/
hp-hr) for CO and 75 g/kW-hr (56 g/hp-hr) for HC. These Phase 2
standards will be followed by Phase 3 standards in 2012 which will
effectively require the equivalent of 50 percent reductions in both HC
and CO as compared to average baseline levels.
We believe that the 2010 and 2012 model years are appropriate for
the second and third phases of snowmobile standards because they allow
an additional four to six years beyond the Phase 1 standards for the
further development and application of advanced emissions control
technology. We expect that the manufacturers will utilize some level of
advanced technology in compliance with the Phase 1 standards, and this
will give the manufacturers some time to evaluate how the advanced
technology they have already applied works in the field as well as give
them several years to work with the certification and compliance
programs before more stringent Phase 2 standards take effect in 2010.
We believe that by the 2010/2012 time frame manufacturers could, at
least in theory, apply advanced technology across essentially their
entire product lines. However, the manufacturers are resource
constrained, and they will need to focus their efforts on compliance
with the Phase 1 and Phase 2 standards prior to the 2010 model year.
There is a need for significant technology development and
manufacturing learning to occur, and there is concern that in this time
frame such technology could not be performance, emissions, and safety
optimized for each application given the number of engine and
snowmobile model combinations that would require optimization. This
would be especially challenging for those manufacturers who rely on
outside suppliers for their engines. Rather, we expect that by the 2012
model year the manufacturers could both apply and optimize advanced
technology to their larger volume families while applying clean
carburetion and electronic fuel injection technology to the rest of
their production. Under this scenario we expect that the manufacturers
could apply optimized advanced technology on around 50 percent of their
production by the 2010 model year, and an additional 20 percent of
their production by the 2012 model year. We do not believe that having
only two
[[Page 68274]]
years lead time between the Phase 2 and Phase 3 standards presents any
problems because compliance with the Phase 3 standards will be achieved
through the broader application of technologies which will already be
applied in compliance with the Phase 2 standards, rather than through
the introduction of new technologies altogether.
As was previously discussed, four-stroke technology has the
potential to significantly reduce HC emissions, even below levels
expected from direct injection two-stroke technology. However, higher
powered four-stroke engines are not currently capable of CO reductions
on the order of those expected from direct injection two-stroke
technology. This is significant given that a very large segment of the
snowmobile market is in higher powered performance sleds. We are
concerned that a straight 50 percent reduction in CO in the Phase 3
standards may deter technology development and constrain the use of
four-stroke technology in this key portion of the snowmobile market. As
the emissions standards become more stringent we believe that it is
important to provide additional flexibility to assure compliance in a
manner which minimizes costs and is consistent with the availability of
technology and the realities of the snowmobile marketplace. Thus, to
allow snowmobile manufacturers the flexibility to base their future
product lines on higher percentages of four-stroke models, we are
adopting a flexible Phase 3 standards scheme that will allow
manufacturers to certify their production to levels which nominally
represent 50 percent reductions in HC and CO. This overall reduction
could be met by other combinations summing to 100 percent such as 70
percent reductions in HC and 30 percent reductions in CO, or any level
between these two points (for example, 60 percent reductions in HC and
40 percent reductions in CO). However, in no case may a manufacturer's
corporate average for the individual pollutants for Phase 3 be less
than 50 percent on HC and 30 percent on CO (the Phase 2 standards).
Some manufacturers have raised safety concerns regarding the use of
advanced technologies on snowmobiles, particularly four-stroke engines
used in high-performance and mountain sleds. In particular, they raised
issues regarding weight and the ability to start the snowmobile in cold
weather. However, we believe these issues can be overcome with
sufficient time and technology. For example, as noted above, smaller
fuel tanks can significantly reduce the weight of four-stroke
snowmobiles. The use of new light-weight materials can also reduce
weight for four-stroke designs. Manufacturers have raised concerns over
cold starting for four-stroke engines because the typical four-stroke
design uses an oil distribution system where the pump and oil are
located in the crankcase (referred to as a ``wet'' sump). During
extremely cold temperatures, the oil becomes thick and provides an
additional load the engine must overcome when starting. However, by
using a ``dry'' sump, where the oil and pump are located in a separate
tank (not in the crankcase), the concern over cold temperature starting
loads due to thickened oil in the crankcase are gone. The new Yamaha
RX-1 four-stroke snowmobile uses a smaller fuel tank and lighter
materials to reduce weight and a dry sump to help cold starting, so
clearly these issues can be addressed.
We believe that, given enough resources and lead time, it is
ultimately feasible at some point beyond the 2012 model year to apply
advanced technology successfully to all snowmobiles and perhaps to even
resolve current design and operating issues with regard to the use of
aftertreatment devices such as catalytic converters. However, it is
difficult to predict at this point when this would be feasible,
especially given the number of smaller volume snowmobile models that
would need development effort once the larger volume models were
optimized in compliance with the Phase 3 standards in 2012. We did
consider standards based on the full application of optimized advanced
technology to all snowmobiles, for example by setting the Phase 3
standards at a level that would require the full application of
advanced technology to all snowmobiles. However, we believe that such
standards are not feasible by 2012 and, we are not confident that we
could choose the appropriate model year beyond 2012 for such standards
given how far in the future such a requirement would be. Such an
approach would also serve to eliminate the benefits associated with the
Phase 3 standards in 2012. There are diverse capabilities and limiting
factors within the industry, and time is needed for an orderly
development and prove out of this advanced technology across the
various models and applications before standards are set which require
its use in all models. Additionally, as these engines have never
previously been regulated or used advanced emission control
technologies in large numbers, we believe it is appropriate to monitor
the development and use of such technologies on snowmobiles before
requiring these technologies for the entire fleet. Thus, we chose not
to set standards at this time based on the optimized application of
advanced technology to all snowmobiles. Nevertheless, we will monitor
the development and application of the advanced technology as
manufacturers work to comply with the Phase 3 standards in 2012 and
will consider a fourth phase of snowmobile standards to take effect
sometime after the 2012 model year.
We have not included a NOX standard for the first two
phases of the snowmobile regulations because NOX emissions
from snowmobiles, particularly two-stroke engines, are very small
compared to levels of HC, CO and PM and we believe that stringent
NOX standards may require the use of technologies that will
lead to increases in HC, PM and CO levels. Technologies that reduce
NOX are likely to increase levels of HC, PM and CO and vice
versa, because technologies to reduce HC, PM and CO emissions would
result in leaner operation. A lean air and fuel mixture causes
NOX emissions to increase. These increases are minor,
however, compared to the reductions of HC, CO and PM that result from
these techniques. On the other hand, any attempt to control the
NOX emissions may have the counter-effect of increasing HC,
CO, and PM emissions, as well as causing the greater secondary PM
concentrations associated with increased HC emissions. This is
especially critical for HC and PM, because NOX would be
regulated primarily for its effect on secondary PM levels.
We are promulgating a NOX standard (actually an HC plus
NOX standard) as part of the third phase of the snowmobile
standards. This standard will essentially cap NOX emissions
from these engines. The reason we are including such standards in the
final phase of the rule as that the third phase of the rule will result
in increases in the use of four-stroke engines. While four-stroke
engines greatly reduce HC and direct PM levels, they increase levels of
NOX. While NOX levels remain substantially lower
than HC and CO levels, they are higher than levels for two-stroke
engines.
Thus, it is appropriate to place a cap on such levels to ensure
that levels do not become so high as to become a substantial concern.
While we are promulgating an effective cap on such emissions, the
standard will not mandate substantial reductions in NOX.
This is because the
[[Page 68275]]
emissions effect on reducing NOX from four-stroke engines is
the same as for two-stroke engines; that is, technologies that
substantially reduce NOX will increase levels of other
pollutants of concern. The only way to reduce NOX emissions
from four-stroke engines (at the same time as reducing HC and CO
levels) would be to use a three-way catalytic converter. We don't have
enough information at this time on the durability or safety
implications of using a three-way catalyst with a four-stroke engine in
snowmobile applications. Three-way catalyst technology is well beyond
the technology reviewed for this rule and would need substantial
additional review before being contemplated for snowmobiles. Thus,
given the overwhelming level of HC and CO compared to NOX,
and the secondary PM expected to result from these levels, it would be
premature and possibly counterproductive to require substantial
NOX reductions from snowmobiles at this time.
2. Are There Opportunities for Averaging, Emission Credits, or Other
Flexibilities?
a. Averaging, banking and trading. Historically, voluntary
emission-credit programs have allowed a manufacturer to certify one or
more engine families at emission levels above the applicable emission
standards, provided that the increased emissions are offset by one or
more engine families certified below the applicable standards. With
averaging alone, the average of all engine families for a particular
manufacturer's production must be at or below that level of the
applicable emission standards. We are adopting separate emission-credit
programs for snowmobiles, off-highway motorcycles, and ATVs. We are
adopting an emission-credit program for the optional ATV engine-based
standards as well as the chassis-based standards.
In addition to the averaging program just described, the emission-
credit program contains banking and trading provisions, which allow
manufacturers to generate emission credits and bank them for future use
in their own averaging program or sell them to another entity. We are
not adopting a credit life limit or credit discounting for these
credits. Unlimited credit life and no discounting increases the
incentive to introduce the clean technologies needed to gain credits.
To generate credits, the engine family's emissions level must be below
the standard, so any credits will result from reducing emissions more
than necessary to meet the standards.
ATVs and Off-highway Motorcycles
Emission credits from off-highway motorcycle and ATVs will be
averaged separately because there are differing degrees of stringency
in the standards for ATVs and off-highway motorcycles long-term and we
do not want off-highway motorcycle credits to dilute the effectiveness
of the ATV standards. This also avoids providing an advantage in the
market to companies that offer both types of products over those that
produce only one type. Also, ATVs certified to the chassis-based
standards or engine-based standards are considered separate averaging
groups with no credit exchanges between the two. We are not allowing
credit exchanges between engine and chassis-based testing because there
is little, if any, correlation between the two test cycles. Without a
strong correlation, it is not possible to establish an exchange rate
between the two programs. For the engine-based (J-1088) ATV standards,
the standards vary by engine size (less than 100 cc, 100 cc up to 225
cc, and 225 cc and greater). We are allowing averaging, banking, and
trading for each of the separate engine-based HC+NOX
standards with no credit exchanges or averaging between the engine size
categories.
We did not propose an averaging, banking, and trading program for
CO for ATVs and off-highway motorcycles because it was not clear if
such provisions would be needed to implement the expected technologies
or if the need would warrant the additional complexity of an averaging
program. We received comments that the 25 g/km CO standard could be
technologically limiting in some instances. Manufacturers recommended
that EPA drop CO the standard from the program and provided no comments
regarding CO averaging. In addition, our recent testing indicates that
the level of the standards may represent a significant technological
challenge to the manufacturers in some cases.
We are retaining CO standards in the final program, and are
establishing different CO standards for off-highway motorcycles and
ATVs, as discussed in Section III.C.1. For ATVs, we are addressing the
feasibility issues by finalizing a standard of 35 g/km. We are not
including averaging or a credits program at this level. We are also
adopting the 35 g/km CO standard for the optional off-highway
motorcycle program with no averaging or credits program. At the 35 g/km
level, we believe averaging is unnecessary and would greatly reduce the
need to control CO, especially for larger manufacturers who have
several engine families with which to average. The engine-based (J-
1088) standards for CO also do not represent levels of stringency where
we believe averaging would be appropriate or necessary. California
certification test data shows that the engine-based (J-1088) CO
standards can be achieved with reasonable compliance margins.
For the primary off-highway motorcycle program, we are retaining
the proposed 25 g/km CO standard. We are providing the option of
averaging for the 25 g/km CO standard, to help manufacturers balance
the need to control CO while meeting stringent NOX
requirements. We believe that the final program with averaging for CO
will enable manufacturers to develop a unified emission-control
strategy to control HC, NOX, and CO, rather than requiring
them to develop unique control strategies driven by the need to meet
the CO standards.
We are adopting FEL caps where we are allowing averaging standards.
For ATVs certified to the 1.5 g/km FTP standard, there will be an FEL
cap of 20 g/km HC+NOX. This cap will also apply to off-
highway motorcycles certified to the 2.0 g/km NOX+HC
standard. For off-highway motorcycles certified to the 25 g/km CO
standard, the CO cap will be 50 g/km. For off-highway motorcycles, we
are also finalizing an option that allows manufacturers to certify to
an average HC+NOX standard of 4.0 g/km, if the manufacturer
certifies all off-highway motorcycles including competition machines.
Under this option, we are limiting FELs to 8.0 g/km. The goal of the
option is to encourage the development and certification of clean
competition products. Without a reasonable FEL limit, manufacturers
could certify two-stroke machines at, or close to, baseline levels.
This is a concern because the majority of manufacturers' product
offerings are likely to be certified below the 4.0 g/km level and
significant credits could be available. We believe the 8.0 g/km limit
ensures significantly cleaner products compared to baseline levels for
competition machines, while providing manufacturers with the incentive
and flexibility to pursue innovative technologies for their competition
products.
As noted above, we have also included engine-based J-1088 standards
for ATVs. The HC+NOX portion of the J-1088 standards can be
met through averaging and we have included reasonable emissions caps
for these standards as well. For engines certified to the permanent
optional J-1088 standards for ATV engines below 100 cc, the emissions
cap is 40.0 g/kW-hr.
[[Page 68276]]
The NOX+HC emissions cap is 32.2 g/kW-hr for engine
certified to the temporary J-1088 standards which are available for all
engine sizes.
Snowmobiles
For snowmobiles, we are adopting an emissions averaging and credit
program for all three phases of standards. Averaging is available for
each phase of standards. Once the program begins in 2006, manufacturers
will make a demonstration of compliance with the applicable corporate
average standards at the end of the model year. If a manufacturer has
achieved a corporate average level below the corporate average
standards, then the manufacturer may bank credits. Manufacturers may
bank credits for use in a current phase of standards based on the
difference between their corporate average and the standards. In order
to bank credits for future use under a subsequent phase of standards,
manufacturers may pull engines from their corporate average for the
current phase of standards and certify them early to a future phase of
standards. The credits must be generated based on the difference
between the FEL for those engines and the phase of standards for which
they are intended to be used. The credits may not be carried forward
for use to meet a subsequent phase of standards.
For example, manufacturers may bank Phase 2 credits in 2007 by
removing engines from their 2007 corporate average for one or both
pollutants and certifying the engines to the Phase 2 standards early.
These Phase 2 credits may then be saved for Phase 2, but may not be
used for Phase 3. Manufacturers may also remove only part of an engine
family for purposes of banking credits. Manufacturers may bank credits
after the end of the model year when they have completed their
demonstration of compliance for that year. The Final Rule includes
provisions for banking credits for a single pollutant, with the other
pollutant remaining in the averaging program for the current model
year. For Phase 3, if a manufacturer chooses to bank credits for only
one pollutant, the manufacturer must use an assigned value for the
other pollutant in the Phase 3 standards formula. We are specifying a
value of 90 g/kW-hr for HC+NOX and 275 g/kW-hr for CO. These
levels ensure no windfall credits using the Phase 3 formula for the
credit-generating engines.
Starting with Phase 3, Family Emission Limits may be set up to the
current average baseline emission levels of 400 g/kW-hr (300 g/hp-hr)
CO and 150 g/kW-hr (110 g/hp-hr) HC. These caps ensure a minimum level
of control for each snowmobile certified under the long-term program.
We believe this is appropriate due to the potential for personal
exposure to very high levels of emissions as well as the potential for
high levels of emissions in areas where several snowmobiles are
operated in a group. We proposed that these limits would be effective
beginning in 2006. We received comments from manufacturers recommending
that we drop the FEL limits because they would create a tremendous near
term workload burden. They commented that manufacturers would need to
modify all product lines for 2006 just to meet the FEL limit. EPA
recognizes that this could be a significant issue in the early years of
the program and could detract from manufacturers' efforts to develop
much cleaner technologies. Thus, we are finalizing the FEL limits only
for Phase 3 and later, beginning in 2012. We believe this helps resolve
the lead-time and workload issues while maintaining the integrity of
the long-term program.
b. Early credits. We believe that allowing manufacturers to
generate credits prior to 2006 has some merit in that it encourages
them to produce cleaner snowmobiles earlier than they otherwise might
and provides early environmental benefits. It would also allow for a
smoother transition to new emission standards in a previously
unregulated industry. However, in the proposal we expressed concern
that an early-credit program could result in the generation of windfall
credits, especially if the credits were generated relative to the
average baseline emissions rates. A manufacturer could choose those
engine families that already emit below the average baseline levels and
certify those families for credit generation purposes without doing
anything to actually reduce their emissions. Clearly this would
undermine any environmental advantages of an early-credit program.
However, we believe that it is possible to design an early-credit
program which provides incentive for the early introduction of cleaner
snowmobiles and also helps ease the transition into the first ever
phase of snowmobile standards while preventing the generation of
windfall credits. The early-credit program described in the following
paragraphs will be available beginning with the 2003 model year. As
with the standard snowmobile emissions averaging, banking and trading
program, credits generated under the early-credit program will be
calculated on a power-weighted basis.
A manufacturer can choose to certify one or more engine families
early for purposes of credit generation. An engine family must at least
meet the Phase 1 standards for both HC and CO to qualify for early
credits, and the credits will be calculated based on the difference
between the certification FEL and the Phase 1 standards. Credits
generated under this option can be used only in compliance with the
Phase 1 standards. Thus, such early credits will expire at the end of
the 2009 model year.
The above discussion of early credits primarily addresses those
snowmobiles that will meet the Phase 1 standards early. However, we
also expect that there will be some engine families introduced prior to
the 2006 model year which could meet Phase 2 standards. For such
engines, a manufacturer may elect to split credits between Phase 1 and
Phase 2. A manufacturer may save credits generated between the
certification FELs and the actual Phase 2 standards for use in Phase 2.
Credits generated between the Phase 1 and Phase 2 standards could be
used for Phase 1 only. Credits generated prior to the start of the
program in 2006 may not be used for Phase 3.
EPA did not receive comments on such programs for off-highway
motorcycle or ATVs and we are not finalizing any additional provisions.
The majority of products currently offered for sale are equipped with
four-stroke engines which raises concerns over the potential for
windfall credits. Due to this issue and the lack of suggestions or
input on the part of commenters, we are not finalizing early credits or
other types of flexibilities for these programs.
c. Nonconformance penalties for recreational vehicles. Section
206(g) of the Act, 42 U.S.C. 7525(g), authorizes EPA to establish
nonconformance penalties (NCPs) for motorcycles and heavy-duty engines
which exceed the applicable emission standard, provided that their
emissions do not exceed an appropriate upper limit. NCPs allow
manufacturers that are technological laggards to temporarily sell their
vehicles by payment of a penalty, rather than being forced out of the
marketplace. One manufacturer suggested that we consider establishing
NCPs for recreational vehicles. Section 213(d) of the Act makes nonroad
standards subject to the provisions of section 206, and directs EPA to
enforce nonroad standards in the same manner as highway vehicles. We
therefore believe that the Act authorizes us to establish NCPs in
appropriate circumstances for nonroad engines and vehicles.
Recreational vehicles are
[[Page 68277]]
similar technologically to highway motorcycles, and NCPs might be
appropriate for recreational vehicles under certain circumstances.
We will consider the need for NCPs two or three years before
compliance with these standards is required. Manufacturers that
determine in that time frame that they are likely to be unable to
comply with the standards should notify us. If we determine that NCPs
are appropriate for recreational vehicles, we would establish
regulations that would specify how to calculate the penalties. While we
have not determined the content of such regulations, it is likely that
they would be similar to our existing NCP regulations for heavy-duty
engines, which are set forth in 40 CFR part 86, subpart L.
3. Are There Voluntary Low-Emission Standards for These Engines?
In the proposal we included a Voluntary Low-Emission Standards
program for recreational vehicles. We did this for two reasons: to
encourage new emission-control technology and to aid the consumer in
choosing clean technologies. We received numerous comments on this
proposed program. The environmental community was supportive of
voluntary standards and encouraged us to adopt permanent labels which
identify the emission performance of the vehicle in a simplistic manner
that would be easily understood by the initial purchaser and any
purchases of used recreational vehicles. Manufacturers of recreational
vehicles ATVs, off-highway motorcycles, and snowmobiles), on the other
hand, did not support voluntary standards. They were supportive of
providing initial purchasers with emission performance information via
temporary consumer labeling, but were opposed to voluntary standards.
Their concern was that voluntary standards or permanent labels could be
used by federal, state, local or any other jurisdictions to limit the
use of recreational vehicles from public lands by allowing access only
to recreational vehicles that meet certain emission criteria.
Manufacturers further argued that our proposed mandatory emission
standards were stringent enough that they would encourage and result in
the use of advanced emission-control technology and that the voluntary
standards would provide no additional incentives.
As stated above, the general purpose of the Voluntary Low-Emission
Standards program is to provide incentives to manufacturers to produce
clean products and thus create market choices for consumers to purchase
these products.\60\ For all three recreational vehicle categories, but
especially for snowmobiles, we are expecting a variety of emission-
control technologies to be used to meet the standards. In all three
categories we expect consumers to have a choice of which technologies
to purchase and that they will base that purchase on an understanding
of key attributes such as cost, performance, noise levels, safety, and
emissions. Thus, an important factor for informing consumer decision is
to provide them information on the relative emissions attributes of a
given model. We believe this can be achieved through a temporary
consumer labeling program without voluntary standards. Therefore, we
are not finalizing a voluntary standard program for recreational
vehicles at this time. We will consider this issue again in the future,
once experience is gained under this program. In addition, given the
manufacturer's opposition, it is not clear that voluntary standards by
themselves would be an effective incentive for manufacturers.
---------------------------------------------------------------------------
\60\ The snowmobile industry (see docket item II-G-221) and a
group of public health and environmental organizations (see docket
item II-G-139) have both expressed their general support for
labeling programs that can provide information on the environmental
performance of various products to consumers.
---------------------------------------------------------------------------
Instead, we will be adopting a consumer labeling program. A label
must be fixed securely to the product prior to arriving at the
dealership but does not have to be permanent and may be removed by the
consumer when placed into use. The label can be in the form of a
removable sticker or decal, or a hang tag affixed to the handlebars or
fuel cap. If a hang tag is used, it must be attached by a cable tie
that cannot be easily removed, except by the ultimate retail consumer.
The label, at a minimum, must include the following information: U.S.
EPA; Clean Air Index (appropriate pollutant, e.g., HC+NOX,
etc.); manufacturer name; vehicle model with engine description (e.g.,
500 cc two-stroke with direct fuel injection); emission performance
rating scale; explanation of scale; and notice stating that label must
be on vehicle prior to sale and can be removed only by the ultimate
retail consumer. In section 1051.135(g) of the regulations, titled
``How must I label and identify the vehicles I produce?,'' we have
developed several equations that determine what the emission
performance rating scale will be for each category. The scale is based
on a rating system of 1.0 through 10.0. A value of 1.0 would be
assigned for the cleanest vehicle, while the dirtiest vehicle would get
a rating of 10.0.
4. What Durability Provisions Apply?
We are adopting several additional provisions to ensure that
emission controls will be effective throughout the life of the vehicle.
This section discusses these provisions for recreational vehicles. More
general certification and compliance provisions, which apply across
different vehicle categories, are discussed in Sections II and VII,
respectively.
a. How long do my engines have to comply. Manufacturers must
produce off-highway motorcycle and ATV engines that comply over a
useful life of 5 years or until the vehicle accumulates 10,000
kilometers, or for ATVs 1,000 hours, whichever occurs first. We
consider the 10,000-kilometer and 1,000 hour values to be minimum
values for useful life, with the requirement that manufacturers must
comply for a longer period if the average life of their vehicles is
longer than this minimum value.
The values being finalized will harmonize EPA's useful life
intervals with those contained in the California program. We proposed a
significantly longer useful life intervals of 30,000 kilometers based
on our understanding of usage rates for the vehicles at the time of the
proposal. We received comments from manufacturers that we overestimated
vehicle usage and commenters recommended that we harmonize the useful
life intervals with California's. We have lowered our estimate of usage
rates based on available data, including new data provided during the
comment period.
Based on our current estimates of usage, we concur with
manufacturers that harmonization with California is the best approach
for establishing minimum useful life intervals. Generally, this will
allow the same emission test data to be used for certification under
both programs. However, this remains the minimum useful life and longer
useful life intervals could be required in cases where the basic
mechanical warranty of the engine or the advertised operating life is
longer than the minimum interval. Average service life information will
help in making such a determination. The manufacturer can alternatively
base the longer useful life on the average service life of the vehicles
where necessary data are available.
For snowmobiles, the minimum useful life is 5 years, 8,000 km, or
400 hours of operation, whichever occurs first. We based these values
on
[[Page 68278]]
discussions with manufacturers regarding typical snowmobile life, and
on emission-modeling data regarding typical snowmobile usage rates.\61\
As with ATVs and off-highway motorcycles, longer useful life intervals
are required where the basic mechanical warranty of the engine or the
advertised operating life is longer than the minimum interval and the
manufacturer may alternatively base the longer useful life on the
average service life of the vehicles where necessary data are
available.
---------------------------------------------------------------------------
\61\ EPA memorandum, ``Emission Modeling for Recreational
Vehicles,'' from Linc Wehrly to Docket A-2000-01, November 13, 2000
(document II-B-19).
---------------------------------------------------------------------------
b. What are the minimum warranty periods for emission controls. For
off-highway motorcycle, ATVs, and snowmobiles, manufacturers must
provide an emission-related warranty for at least half of the minimum
useful life period. These periods could be longer if the manufacturer
offers a longer mechanical warranty for the engine or any of its
components; this includes extended warranties that are available for an
extra price. See Sec. 1051.120 for a description of which components
are emission-related.
We have included in our final rule an optional set of standards for
off-highway motorcycles that would require the certification of
competition motorcycles. However, for those individual vehicles
actually used in organized competition events, it may be appropriate to
exclude competition motorcycles from warranty coverage. Machines used
in competition, even part of the time, may be subject to usage that can
cause premature degradation of the engine and related components.
Competition riders may place a premium on winning at the expense of
engine durability or could otherwise damage the vehicle during the
competition events. In fact, most manufacturers do not offer any
mechanical warranty on vehicles used in competition. In addition,
motorcycles used only for competition may be modified by the user in
ways that alter the emissions characteristics of the vehicle.\62\ We do
not believe it is reasonable to hold manufacturers responsible for the
emission warranty for such vehicles.
---------------------------------------------------------------------------
\62\ While it is possible that the user could make modifications
to their competition off-highway motorcycle that alter the emissions
characteristics of the vehicle, we do not expect tampering to be a
problem for those competition vehicles certifying to our voluntary
standard of 4.0 g/km HC+NOX because the technologies
required to meet this standard, four-stroke engines and direct fuel
injection two-stroke engines, are inherent to the engine and will be
optimized for maximum engine performance as well as emissions
performance. Thus, any modifications would actually reduce rather
than improve engine performance.
---------------------------------------------------------------------------
c. How do I demonstrate emission durability during certification.
Durability demonstration for off-highway motorcycles, ATVs, and
snowmobiles includes a requirement to run the engines long enough to
develop and justify the full life deterioration factor. This allows
manufacturers to generate a deterioration factor that helps ensure that
the engines will continue to control emissions over a lifetime of
operation. Snowmobiles also must run out to the end of the useful life
for purposes of durability demonstration and generating deterioration
factors.
d. What maintenance is allowed during service accumulation. For
vehicles certified to the minimum useful life, emission-related
maintenance is generally not allowed during service accumulation. The
only maintenance that may be done must be (1) regularly scheduled, (2)
unrelated to emissions, and (3) technologically necessary. This
typically includes changing engine oil, oil filter, fuel filter, and
air filter.
5. Do These Standards Apply to Alternative-Fueled Engines?
These standards apply to all spark-ignited recreational vehicles,
without regard to the type of fuel used. However, because we are not
aware of any alternative-fueled recreational vehicles sold into the
U.S. market, we are not adopting extensive special provisions to
address them at this time.
6. Is EPA Controlling Crankcase Emissions?
We are requiring that new off-highway motorcycles and ATVs not emit
crankcase vapors directly to the atmosphere. This requirement will
phase in beginning in 2006 and be fully phased in by 2007. California's
regulations for off-highway motorcycles and ATVs, which has been in
effect since 1997, also prohibits the venting of crankcase vapors into
the atmosphere. The major ATV manufacturers sell many of their
California certified ATV models federally as 50-state applications.
Thus, many ATVs sold federally already control crankcase emissions. The
only exceptions could be some of the small youth ATV models that are
imported from Asia.
The typical control strategy used to control crankcase emissions is
to route the crankcase vapors back to the engine intake. This is
consistent with our previous regulation of crankcase emissions from
such diverse sources as highway motorcycles, outboard and personal
water craft marine engines, locomotives, and passenger cars. We have
data from California ARB showing that a performance-based four-stroke
off-highway motorcycle experienced considerably higher tailpipe
emission results when crankcase emissions were routed back into the
intake of the engine, illustrating the potentially high levels of
crankcase emissions that exist.\63\
---------------------------------------------------------------------------
\63\ ``Closed Crankcase Exhaust Emissions from Four-Stoke
Competition Off-highway Motorcycle,'' EPA memo from L. Wehrly to
Docket A-2000-01, September 10, 2001 (document II-B-25).
---------------------------------------------------------------------------
New snowmobiles must also have closed crankcases, beginning in
2006. This requirement is relevant only for four-stroke snowmobiles,
however, since two-stroke engines, by virtue of their operation, have
closed crankcases. Information on the costs and benefits of this action
can be found in the Final Regulatory Support Document.
D. Testing Requirements
1. What Duty Cycles Are Used To Measure Emissions?
Testing a vehicle or engine for emissions typically consists of
exercising it over a prescribed duty cycle of speeds and loads,
typically using a chassis or engine dynamometer. The nature of the duty
cycle used for determining compliance with emission standards during
the certification process is critical in evaluating the likely emission
performance of engines designed to those standards. Duty cycles must be
relatively comparable to the way equipment is actually used because if
they are not, then compliance with emission standards would not assure
that emissions from the equipment are actually being reduced in use as
intended.
a. Off-highway Motorcycles and ATVs. For testing off-highway
motorcycles and ATVs, we specify the current highway motorcycle test
procedure be used for measuring emissions. The highway motorcycle test
procedure is very similar to the test procedure as used for light-duty
vehicles (i.e., passenger cars and trucks) and is referred to as the
Federal Test Procedure (FTP). The FTP for a particular class of engine
or equipment is actually the aggregate of all of the emission tests
that the engine or equipment must meet to be certified. However, the
term FTP has also been used traditionally to refer to the exhaust
emission test based on the Urban Dynamometer Driving Schedule (UDDS),
also referred to as the LA-4 (Los Angeles Driving Cycle i
4).
The UDDS is a chassis dynamometer driving cycle that consists of
numerous ``hills''
[[Page 68279]]
which represent a driving event. Each hill includes accelerations,
steady-state operation, and decelerations. There is an idle between
each hill. The FTP consists of a cold start UDDS, a 10-minute soak, and
a hot start. The emissions from these three separate events are
collected into three unique bags. Each bag represents one of the
events. Bag 1 represents cold transient operation, Bag 2 represents
cold stabilized operation, and Bag 3 represents hot transient
operation.
For highway motorcycles, we have three classes based on engine
displacement, with Class I (50 to 169 cc) being the smallest and Class
III (280 cc and over) being the largest. The highway motorcycle
regulations allow Class I motorcycles to be tested on a less severe
UDDS cycle than the Class II and III motorcycles. This is accomplished
by reducing the acceleration and deceleration rates on some the more
aggressive ``hills.'' We proposed to use this same class/cycle
distinction for off-highway motorcycles and ATVs. In other words, we
proposed that off-highway motorcycles and ATVs with an engine
displacement at or below 169 cc would be tested over the FTP test cycle
for Class I highway motorcycles. We proposed that off-highway
motorcycles and ATVs with engine displacements greater than 169 cc
would be tested over the FTP test cycle for Class II and Class III
highway motorcycles. We requested comment on the appropriateness of
allowing the use of the Class I test cycle for all ATVs.
Manufacturers have expressed concerns over the appropriateness of
testing ATVs using the FTP and the ability of some ATVs to be run on
the test cycle. Manufacturers recommended for FTP testing, that all
ATVs be tested over the Class I cycle. Manufacturers stated that the
Class I cycle top speed of 36 mph would be ``much more representative''
of ATV operation than the 57 mph top speed of the Class III cycle.
Manufacturers also noted that California FTP testing is based on the
use of the Class I cycle for all ATVs and that the EPA program would
need to be changed allow for harmonization. Manufacturers did not raise
these same concern for off-highway motorcycles which are tested in
accordance with the highway motorcycle classifications for California.
After considering this issue further, we concur with the
manufacturer's comments and are finalizing the Class I cycle for all
ATVs. One of the objectives of the final program is to allow
harmonization with California and this change is fundamental in the
manufacturers' ability to use the same FTP test data for both programs.
Also, the average speeds of in-use ATVs appear to be significantly
lower than we estimated in the analysis for the proposal (8-13 mph
compared to 20 mph). The new data on ATV usage alleviates concerns that
the lower speeds of the Class I test cycle might miss significant high-
speed ATV operation. The change in the test procedure is directionally
consistent with this new data. In addition, the change in test
procedure will enable ATVs in general to be tested over the FTP with
fewer issues concerning the ability of the vehicles to operate over the
driving cycle. We are finalizing the test procedure requirements as
proposed for off-highway motorcycles. We believe that the
manufacturer's concerns regarding the FTP are also addressed by the
option to test the smallest ATVs (up to 100 cc) to J-1088 standards
permanently. These vehicles are typically governed to top speeds below
the 36 mph contained in the Class I FTP cycle. Also, the small
displacement ATVs may be most strenuously tested (i.e., more operation
at high loads) on the FTP due to their lower horsepower output.
We acknowledge that chassis dynamometers for ATVs could be costly
to purchase and difficult to put in place in the near term, especially
for smaller manufacturers. As discussed in Section III.C.1.b, we are
allowing the use of the J1088 engine test cycle as a transitional
option through model year 2008. The J1088 option expires after 2008 and
the FTP becomes the required test cycle in 2009. As noted above, EPA is
currently in discussions with ATV manufacturers to determine whether a
new test cycle is appropriate. The J1088 may be discontinued earlier
than 2009 if another test procedure is implemented.
b. Snowmobiles. We are adopting the snowmobile duty cycle developed
by Southwest Research Institute (SwRI) in cooperation with the
International Snowmobile Manufacturers Association (ISMA) for all
snowmobile emission testing.\64\ The test procedure consists of two
main parts; the duty cycle that the snowmobile engine operates over
during testing and other testing protocols surrounding the measurement
of emissions (sampling and analytical equipment, specification of test
fuel, atmospheric conditions for testing, etc.). While the duty cycle
was developed specifically to roughly approximate snowmobile operation,
many of the testing protocols are well established in other EPA
emission-control programs and have been simply adapted where
appropriate for snowmobiles.
---------------------------------------------------------------------------
\64\ ``Development and Validation of a Snowmobile Engine
Emission Test Procedure,'' Jeff J. White, Southwest Research
Institute and Christopher W. Wright, Arctic Cat, Inc., Society of
Automotive Engineers paper 982017, September, 1998. (Docket A-2000-
1; document II-D-05).
---------------------------------------------------------------------------
The snowmobile duty cycle was developed by instrumenting several
snowmobiles and operating them in the field in a variety of typical
riding styles, including aggressive (trail), moderate (trail), double
(trail with operator and one passenger), freestyle (off-trail), and
lake driving. A statistical analysis of the collected data produced the
five mode steady-state test cycle is shown in Table III.D-1. This duty
cycle is the one that was used to generate the baseline emissions
levels for snowmobiles, and we believe it is the most appropriate for
demonstrating compliance with the snowmobile emission standards at this
time.
Table III.D-1.--Snowmobile Engine Test Cycle
----------------------------------------------------------------------------------------------------------------
Mode
Engine parameter ---------------------------------------------------------------------
1 2 3 4 5
----------------------------------------------------------------------------------------------------------------
Normalized Speed.......................... 1.00 0.85 0.75 0.65 Idle
Normalized Torque......................... 1.00 0.51 0.33 0.19 0.00
Relative Weighting (in percent)........... 12 27 25 31 5
----------------------------------------------------------------------------------------------------------------
The rest of the testing protocol is largely derived from our
regulations for marine outboard and personal water craft engines, as
recommended in the SwRI/ISMA test cycle development work (61 FR 52088,
October 4, 1996).
[[Page 68280]]
The testing equipment and procedures from that regulation are generally
appropriate for snowmobiles, including the provisions for raw exhaust
gas sampling which are being adopted here for snowmobiles.
Unlike marine engines, however, snowmobiles tend to operate in cold
ambient temperatures. Thus, some provision needs to be made in the
snowmobile test procedure to account for the colder ambient
temperatures typical of snowmobile operation. Since snowmobile
carburetors are jetted for specific ambient temperatures and pressures,
appropriate accounting for typical operating temperatures is important
to assure that anticipated emissions reductions actually occur in use.
We proposed that snowmobile engine inlet air temperature be between -
15[deg]
C and -5[deg]
C (5[deg] F and 23[deg] F), but that the ambient
temperature in the test cell not be required to be refrigerated. We
received comments stating that this approach would be expensive due to
the need for refrigeration equipment, pointing out that the snowmobile
manufacturers do not currently have the capacity for cold testing.
Further, we received comments that accurate emissions results can be
obtained using appropriate jetting determined by extrapolating from the
manufacturer's jet chart (if necessary).
We agree that emissions can be accurately measured at higher
ambient temperatures provided that the proper compensation be made in
the fueling system. For carbureted engines this means jetting the
engine appropriately for the test temperature. For electronically
controlled engines this doesn't tend to be an issue because such
technology generally includes temperature compensation in its control
algorithms. However, one manufacturer stated that for snowmobiles that
have electronically controlled engines, it would be preferable and
environmentally appropriate to test with colder inlet temperatures.
Thus, we are adopting the option to allow snowmobile testing using
either cold engine inlet air temperatures between -15[deg]
C and -
5[deg]
C (5[deg]
F and 23[deg] F) or warm engine inlet air temperatures
between 20[deg]
C and 30[deg]
C (68[deg] F and 86[deg] F). However,
depending on the location of the air box where inlet air enters the
engine intake system, the inlet temperature could be considerably
warmer than ambient conditions. For a snowmobile that does not have
temperature compensating capabilities, it could be possible to get a
moderate emission reduction due to the increase in air density that
results at colder temperatures from the artificially induced test inlet
air. These emission reductions would not occur in real operation since
actual inlet air would be warmer. Therefore, to use the colder inlet
temperature option, a manufacturer must demonstrate that for the given
engine family, the temperature of the inlet air within the air box is
consistent with the inlet-air temperature test conditions.
2. What Fuels Will Be Used During Exhaust Emission Testing?
We are adopting fuel specifications as proposed for all
recreational vehicles that we have specified for 2004 and later light-
duty vehicles.
3. Are There Production-Line Testing Provisions for These Engines?
Recreational vehicle or engine manufacturers must perform emission
tests on a small percentage of their production as it leaves the
assembly line to ensure that production vehicles operate at certified
emission levels. The broad outline of this program is discussed in
Section II.C.4 above. Production-line testing must be performed using
the same test procedures as for certification testing.
E. Special Compliance Provisions
As described in Section XI.B, the report of the inter-agency Small
Business Advocacy Review Panel addresses the concerns of small-volume
manufacturers of recreational vehicles. We proposed to adopt the
provisions recommended by the panel and received comments on the
proposals. We are finalizing the provisions below as proposed, with the
modifications as noted.
Off-Highway Motorcycles and ATVs
To identify representatives of small businesses for this process,
we used the definitions provided by the Small Business Administration
for motorcycles, ATVs, and snowmobiles (fewer than 500 employees).
Eleven small businesses agreed to serve as small-entity
representatives. These companies represented a cross-section of off-
highway motorcycle, ATV, and snowmobile manufacturers, as well as
importers of off-highway motorcycles and ATVs.
As discussed above, our emission standards for off-highway
motorcycles and ATVs will likely necessitate the widespread use of
four-stroke engines. Most small-volume off-highway motorcycle and ATV
importers--and to a lesser degree, small-volume manufacturers--
currently use two-stroke engines. While four-stroke engines are common
in motorcycles and ATVs in general, their adoption by any manufacturer
is still a significant business challenge. Small manufacturers of these
engines may face additional challenges in certifying engines to
emission standards, because the cost of certification would be spread
over the relatively few engines they produce. These higher per-unit
costs may place small manufacturers at a competitive disadvantage
without specific provisions to address this burden.
We are applying the flexibilities described below to engines
produced or imported by small entities with combined off-highway
motorcycle and ATV annual sales of fewer than 5,000 units. The inter-
agency panel recommended these provisions to address the potentially
significant adverse effects on small entities of an emission standard
that may require conversion to four-stroke engines. The 5,000-unit
threshold is intended to focus these flexibilities on those segments of
the market where the need is likely to be greatest and to ensure that
the flexibilities do not result in significant adverse environmental
effects during the period of additional lead-time recommended
below.\65\ In addition, we are limiting some or all of these
flexibilities to companies that are in existence or have product sales
at the time we proposed emission standards to avoid creating arbitrary
opportunities in the import sector, and to guard against the
possibility of corporate reorganization, entry into the market, or
other action for the sole purpose of circumventing emission standards.
---------------------------------------------------------------------------
\65\ For example, importers may have access to large supplies of
vehicles from major overseas manufacturers and potentially could
substantially increase their market share by selling less expensive
noncomplying products.
---------------------------------------------------------------------------
Snowmobiles
There are only a few small snowmobile manufacturers and they sell
only a few hundred sleds a year, which represents less than 0.5 percent
of total annual production. Therefore, the per-unit cost of regulation
may be significantly higher for these small entities because they
produce very low volumes. Additionally, these companies do not have the
design and engineering resources to tackle compliance with emission
standard requirements at the same time as large manufacturers and tend
to have limited ability to invest the capital necessary to conduct
emission testing related to research, development, and certification.
Finally, the requirements of the snowmobile program may be infeasible
or highly impractical because some small-volume
[[Page 68281]]
manufacturers may have typically produced engines with unique designs
or calibrations to serve niche markets (such as mountain riding). The
new snowmobile emission standards may impose significant economic
hardship on these few manufacturers whose market presence is small. We
therefore believe significant flexibility is necessary and appropriate
for this category of small entities, as described below.
Flexibilities
1. Additional lead time. We are adopting a delay of two years
beyond the date larger businesses must comply to ease the burden for
small businesses. This will provide extra time to develop technology
and, in the case of importers, extra time to resolve supplier issues
that may arise. The two-year delay also applies to the timing of the
Phase 2 standards for snowmobiles.
In addition, for small snowmobile manufacturers, the emission
standards phase in over an additional two years at a rate of 50
percent, then 100 percent. Phase 1 phases in at 50/50/100 percent in
2008/2009/2010 and Phase 2 phases in at 50/50/100 percent in 2012/2013/
2014.
2. Design-based certification. The process of certification is a
business cost and lead time issue that may place a disproportionate
burden on small entities, particularly importers. Certification is a
fixed cost of doing business, which is potentially more burdensome on a
unit-cost basis for small entities. It is potentially an even greater
challenge, since some small entities will either contract emission
testing to other parties or, in the case of importers, perhaps rely on
off-shore manufacturers to develop and certify imported engines.
Small-volume manufacturers may use design-based certification,
which allows us to issue a certificate to a small business for the
emission-performance standard based on a demonstration that engines or
vehicles of a similar design criteria meet the standards of the
individual engine family. The small vehicle manufacturer must
demonstrate that their engine uses a design similar to or superior to
one that is being used by other manufacturers that has been shown
through prior emission testing to meet the standards. The demonstration
must be based in part on emission test data from engines of a similar
design. Under a design-based certification program, a manufacturer
provides evidence in the application for certification that an engine
or vehicle meets the applicable standards for its useful life based on
comparing its design (for example, the use a four-stroke engine,
advanced fuel injection, or any other particular technology or
calibration) to that of a previously tested engine. The design criteria
might include specifications for engine type, calibrations (spark
timing, air /fuel ratio, etc.), and other emission-critical features,
including, if appropriate, catalysts (size, efficiency, precious metal
loading). Manufacturers submit adequate engineering and other
information about their individual designs showing that they will meet
emission standards for the useful life.
3. Broaden engine families. Small businesses may define their
engine families more broadly, putting all their models into one engine
family (or more) for certification purposes. Manufacturers may then
certify their engines using the ``worst-case'' configuration within the
family.
A small manufacturer might need to conduct certification emission
testing rather than pursuing design-based certification. Such a
manufacturer would likely find broadened engine families useful.
4. Production-line testing waiver. As discussed above,
manufacturers must test a small sampling of production engines to
ensure that production engines meet emission standards. We are waiving
production-line testing requirements for small manufacturers. This will
eliminate or substantially reduce production-line testing requirements
for small businesses.
5. Use of assigned deterioration factors for certification. Small
manufacturers may use deterioration factors assigned by EPA. Rather
than performing a durability demonstration for each family for
certification, manufacturers may elect to use deterioration factors
determined by us to demonstrate emission levels at the end of the
useful life, thus reducing the development and testing burden. This
might be a very useful and cost-beneficial option for a small
manufacturer opting to perform certification emission testing instead
of design-based certification.
6. Using emission standards and certification from other EPA
programs. A wide array of engines certified to other EPA programs may
be used in recreational vehicles. For example, there is a large variety
of engines certified to EPA lawn and garden standards (Small SI).
Manufacturers of recreational vehicles may use engines certified to any
other EPA standards for five years. Under this approach, engines
certified to the Small SI standards may be used in recreational
vehicles. These engines would then meet the Small SI standards and
related provisions rather than those adopted in this document for
recreational vehicles. Small businesses using these engines will not
have to recertify them, as long as they do not alter the engines in a
way that might cause it to exceed the emission standards it was
originally certified to meet. Also, the recreational vehicle
application may not be the primary intended application for the engine.
Additionally, a certified snowmobile engine produced by a large
snowmobile manufacturer may be used by a small snowmobile manufacturer,
as long as the small manufacturer did not change the engine in a way
that might cause it to exceed the snowmobile emission standards. This
provides a reasonable degree of emission control. For example, if a
manufacturer changed a certified engine only by replacing the stock
exhaust pipes with pipes of similar configuration or the stock muffler
and air intake box with a muffler and air box of similar air flow, the
engine would still be eligible for this flexibility option, subject to
our review. The manufacturer may also change the carburetor to have a
leaner air-fuel ratio without losing eligibility. The manufacturer in
such cases could establish a reasonable basis for knowing that
emissions performance is not negatively affected by the changes.
However, if the manufacturer changed the bore or stroke of the engine,
it would no longer qualify, as emissions might increase beyond the
level of the standard.
7. Averaging, banking, and trading. For the overall program, we are
adopting corporate-average emission standards with opportunities for
banking and trading of emission credits. We expect the averaging
provisions to be most helpful to manufacturers with broad product
lines. Small manufacturers and small importers with only a few models
might not have as much opportunity to take advantage of these
flexibilities. However, we received comment from one small manufacturer
supporting these types of provisions as a critical component of the
program. Therefore, we are adopting corporate-average emission
standards with opportunities for banking and trading of emission
credits for small manufacturers.
8. Hardship provisions. We are adopting provisions to address
hardship circumstances, as described in Section VII.C.
9. Unique snowmobile engines. Even with the broad flexibilities
described above, there may be a situation where a small snowmobile
manufacturer cannot comply. Therefore, we are adopting an additional
provision to allow a small
[[Page 68282]]
snowmobile manufacturer to petition us for relaxed standards for one or
more engine families. The manufacturer must justify that the engine has
unique design, calibration, or operating characteristics that make it
atypical and infeasible or highly impractical to meet the emission-
reduction requirements, considering technology, cost, and other
factors. At our discretion, we may then set an alternative standard at
a level between the prescribed standard and the baseline level, which
would likely apply until the engine family is retired or modified in a
way that might alter emissions. These engines will be excluded from
averaging calculations. We proposed that this provision be limited to
300 snowmobiles per year. However, we received comment that this limit
is too restrictive to be of much assistance to small businesses. Based
on this comment we are adopting a limit for this provision of 600
snowmobiles per year.
F. Technological Feasibility of the Standards
1. Off-highway Motorcycles and ATVs
We believe the new emission standards are technologically feasible
given the availability of emission-control technologies, as described
below.
a. What are the baseline technologies and emission levels? As
discussed earlier, off-highway motorcycles and ATVs are equipped with
relatively small (48 to 650 cc) high-performance two-or four-stroke
single cylinder engines that are either air-or liquid-cooled.\66\ Since
these vehicles are unregulated outside of the state of California, the
main emphasis of engine design is on performance, durability, and cost
and thus they generally have no emission controls. The fuel systems
used on these engines are almost exclusively carburetted. Two-stroke
engines lubricate the piston and crankshaft by mixing oil with the air
and fuel mixture. This is accomplished by most contemporary two-stroke
engines with a pump that sends two-cycle oil from a separate oil
reserve to the carburetor where it is mixed with the air and fuel
mixture. Some less expensive two-stroke engines require that the oil be
mixed with the gasoline in the fuel tank. Four-stroke engines inject
oil via a pump throughout the engine as the means of lubrication. With
the exception of those vehicles certified in California, most of these
engines are unregulated and thus have no emission controls. For ATVs,
approximately 80-percent use four-stroke engines while only 55 percent
of off-highway motorcycles use four-stroke engines. The average HC
emissions for two-stroke engines are about 35 g/km, while the average
for four-stroke engines are 1.5 g/km. CO emissions levels are very
similar between the types of engines with two-stroke levels of
approximately 34 g/km and four-stroke levels of 30 g/km. For
performance and durability reasons, off-highway motorcycle and ATV
engines all tend to operate with a ``rich'' air and fuel mixture. That
is, they operate with excess fuel, which enhances performance and
allows engine cooling to promote longer engine life. However, rich
operation results in high levels of HC, CO, and PM emissions. Also,
two-stroke engines tend to have high scavenging losses, where up to a
third of the unburned air and fuel mixture goes out of the exhaust
resulting in high levels of HC emissions.
---------------------------------------------------------------------------
\66\ The engines are small relative to automotive engines. For
example, automotive engines typically range from one liter to well
over five liters in displacement, whereas off-highway motorcycles
range from 0.05 liters to 0.65 liters.
---------------------------------------------------------------------------
b. What technology approaches are available to control emissions?
Several approaches are available to control emissions from off-highway
motorcycles and ATVs. The simplest approach consists of modifications
to the base engine, fuel system, cooling system, and recalibration of
the air and fuel mixture. These changes may include adjusting valve
timing for four-stroke engines, changing from air-to liquid-cooling,
and using advanced carburetion techniques or electronic fuel injection
instead of traditional carburetion systems. Other approaches may
include secondary air injected into the exhaust, an oxidation or three-
way catalyst, or a combination of secondary air and a catalyst. The
engine technology that may have the most potential for maximizing
emission reductions from two-stroke engines is direct fuel injection.
Direct fuel injection is able to reduce or even eliminate scavenging
losses by pumping only air through the engine and then injecting fuel
into the combustion chamber after the intake and exhaust ports have
closed. Using oxidation catalysts with direct injection may reduce
emissions even further. Finally, converting from two-stroke to four-
stroke engine technology will significantly reduce HC emissions. All of
these technologies have the capability to reduce HC and CO emissions.
We expect none of these technologies to negatively affect noise,
safety, or energy factors. Fuel injection can improve the combustion
process which can result in lower engine noise. The vast majority of
four-stroke engines used in off-highway motorcycles and ATVs are
considerably quieter than their two-stroke counterparts. Fuel injection
has no impact on safety and four-stroke engines often have a more
``forgiving'' power band which means the typical operator may find the
performance of the machine to be more reasonable and safe. Fuel
injection, the enleanment of the air and fuel mixture and four-stroke
technology all can result in significant reductions in fuel
consumption.
c. What technologies are most likely to be used to meet emission
standards?
Four-Stroke Engines
Most manufacturers have experience with four-stroke engine
technology and currently have several models powered by four-stroke
engines. This is especially true in the ATV market where four-stroke
engines account for 80 percent of sales. Because four-stroke engines
have been so prevalent over the last 10 years in the off-highway
motorcycle and ATV industry, manufacturers have developed a high level
of confidence in four-stroke technology and its application.
Manufacturers of off-highway motorcycles and ATVs utilizing four-
stroke engines will need to make some minor calibration changes and
improvements to the carburetor to meet emission standards for the 2006
model year. Some of these modifications may have already been
incorporated in response to California requirements. The calibration
changes will most likely consist of reducing the amount of fuel in the
air-fuel mixture. This is commonly referred to as leaning out the air-
fuel ratio. Although four-stroke engines produce considerably lower
levels of HC than two-stroke engines, the four-stroke engines used in
off-highway motorcycles and ATVs all tend to be calibrated to operate
with a rich air-fuel ratio for performance and durability benefits.
This rich operation results in high levels of CO, since CO is formed in
the engine when there is a lack of oxygen to complete combustion. We
believe that many of these engines are calibrated to operate richer
than needed, because they have either never had to consider emissions
when optimizing air-fuel ratio or those that are certified to the
California standards can operate richer because the California ATV CO
standards are fairly lenient. Carburetors with tighter tolerances
ensure more precise flow of fuel and air, resulting in better fuel
atomization (i.e., smaller fuel droplets), better combustion, and lower
emissions.
In addition to converting to four-stroke technology and making some
minor calibration and carburetion improvements to meet the 2006
[[Page 68283]]
emission standards, manufacturers may need to use secondary air
injection on some models. Secondary air has been used by passenger cars
and highway motorcycles for many years as a means to help control HC
and CO. The hot exhaust gases coming from the combustion chamber
contain significant levels of unburned HC and CO. If sufficient oxygen
is present, these gases will continue to react in the exhaust system,
reducing the amount of pollution emitted into the atmosphere. To assure
that sufficient oxygen is present in the exhaust, air is injected into
the exhaust system. For off-highway motorcycles and ATVs, the
additional air can be injected into the exhaust manifold using a series
of check valves which use the normal pressure pulsations in the exhaust
manifold to draw air from outside, commonly referred to as pulse air
injection. We have tested several four-stroke ATVs with secondary air
injected into the exhaust manifold and found that the HC and CO
emission levels were below the standards (further details of our
secondary air testing are described in the Final Regulatory Support
Document).
A small number of models in California have been equipped with
secondary air technology. It is likely that some manufacturers will opt
to use secondary air systems to reduce emissions in addition to
enleanment strategies to meet EPA standards. We believe this may be
especially true for ATVs meeting the 1.5 g/km HC+NOX
standard. Using these systems would also provide manufacturers with
more flexibility within the averaging scheme and would allow them to
avoid any negative affects on performance that could accompany
excessive enleanment. Also, several models are not certified to
California standards, including some four-stroke models. Manufacturers
may use secondary air on a more widespread basis to bring all models
into compliance.
Since the emission standards address HC + NOX, as well
as CO, manufacturers will have to use an emission-control strategy or
technology that doesn't cause NOX emissions to increase
disproportionately. However, since all of these vehicles operate with
rich air-fuel ratios, as discussed above, NOX levels from
these engines are generally low and strategies designed to focus on HC
reduction allow manufacturers to meet emission standards with no
significant increase in NOX levels.
Two-Stroke Engines
Off-highway motorcycles and ATVs using two-stroke engines will
present a greater challenge for compliance with emission standards.
Since baseline HC and CO emission levels are so high for two-stroke
engines, it would be very difficult for any two-stroke engine to meet
our standards with current production technologies. Although catalysts
have been used for two-stroke powered mopeds, scooters, and small
displacement highway motorcycles in Europe and Asia, the standards and
test cycles are significantly different from ours and there is no way
to make reasonable comparisons. We have not performed any testing, nor
are we aware of any emission test data on the use of catalysts on ATV
and off-highway motorcycle two-stroke engines. Therefore, we do not
believe that catalysts would be available for two-stroke engines that
would meet our standards in the time frame necessary to comply with our
program. Direct fuel injection has been successfully applied to two-
stroke engines used in marine personal water craft, outboard engines,
and small mopeds and scooters and is just now being looked at for off-
highway motorcycle applications. However, as discussed below, even this
advanced technology cannot meet our standards alone.
As described in Section III.C.1.a, we are including an optional
standard for off-highway motorcycles of 4.0 g/km HC + NOX,
for manufacturers willing to certify competition motorcycles that would
otherwise be exempt from emission standards. We received comment from
REV! Motorcycles in support of this level. Rev! plans to manufacture
two-stroke off-highway motorcycles equipped with direct injection.
Based on an early analysis of the technology, REV! requested that EPA
consider establishing a 4.0 g/km standard to allow them to pursue the
technology and have a realistic opportunity to meet emission standards.
According to their comments, they believe that their engines will be
capable of meeting the 4.0 g/km standard without the use of a catalyst.
Perhaps most importantly, REV! believes that this is a viable
technology approach for competition models, which have very high
baseline emissions.
REV! shared their plans and emissions projections for a single
prototype model of competition motorcycle. Production units, additional
models, or motorcycles produced by other manufacturers using similar
technologies may not be able to achieve the 4.0 g/km level. The 4.0 g/
km level represents an HC reduction of 90 percent or more from baseline
levels for some competition motorcycles, which is likely to be very
challenging. This is one reason EPA is also allowing averaging,
banking, and trading for this option. Averaging will provide
flexibility to manufacturers who have some models that, while very
clean relative to baseline levels, are above the 4.0 g/km standard.
Manufacturers will be able to use credits, for example, from the sale
of four-stroke machines with emissions below 4.0 g/km to achieve the
4.0 g/km standard on average.
2. Snowmobiles
a. What are the baseline technologies and emission levels? As
discussed earlier, snowmobiles are equipped with relatively small high-
performance two-stroke two and three cylinder engines that are either
air-or liquid-cooled. Since these vehicles are currently unregulated,
the main emphasis of engine design is on performance, durability, and
cost and thus they have no emission controls. The fuel system used on
these engines are almost exclusively carburetors, although some have
electronic fuel injection. Two-stroke engines lubricate the piston and
crankshaft by mixing oil with the air and fuel mixture. This is
accomplished by most contemporary two-stroke engines with a pump that
sends two-cycle oil from a separate oil reserve to the carburetor where
it is mixed with the air and fuel mixture. Some less expensive two-
stroke engines require that the oil be mixed with the gasoline in the
fuel tank. Snowmobiles currently operate with a ``rich'' air and fuel
mixture. That is, they operate with excess fuel, which enhances
performance and allows engine cooling which promotes longer lasting
engine life. However, rich operation results in high levels of HC, CO,
and PM emissions. Also, two-stroke engines tend to have high scavenging
losses, where up to a third of the unburned air and fuel mixture goes
out of the exhaust resulting in high levels of raw HC. Current average
snowmobile emission rates are 400 g/kW-hr (296 g/hp-hr) CO and 150 g/
kW-hr (111 g/hp-hr) HC. There are however, at least two snowmobile
models that use four-stroke engines. Two companies currently have a
moderate-powered four-stroke touring model that has very low emissions.
One sled uses a small advanced automotive engine, while the other uses
a modified ATV engine. Both engines are very sophisticated, using
electronic fuel injection and computer-based closed-loop control. The
other snowmobile manufacturers are planning to release four-stroke
models for the 2003 model year, but are focusing on higher performing
models that, according to
[[Page 68284]]
the manufacturers, may not have as good of emissions control as the
production four-stroke touring models.
b. What technology approaches are available to control emissions?
We believe the new emission standards are technologically feasible. A
variety of technologies are currently available or in stages of
development to be available for use on two-stroke snowmobiles. These
include improvements to carburetion (improved fuel control and
atomization, as well as improved production tolerances), enleanment
strategies for both carbureted and fuel injected engines, and semi-
direct and direct fuel injection. In addition to these two-stroke
technologies, converting to four-stroke engines is also feasible. Each
of these is discussed in the following paragraphs.
There are several ways to improve carburetion in snowmobile
engines. First, strategies to improve fuel atomization promote more
complete combustion of the fuel/air mixture. Additionally, improved
production tolerances enable more consistent fuel metering. Both of
these changes allow more accurate control of air-fuel ratios.
Snowmobile engines are currently calibrated with rich air-fuel ratios
for durability reasons. Leaner calibrations to CO and HC emissions pose
a challenge for maintaining engine durability, but many engine
improvements are available to prevent problems. These include changes
to the cylinder head, pistons, ports and pipes to reduce knock. In
addition critical engine components can be made more robust to improve
durability.
The same calibration changes to the air-fuel ratio just discussed
for carbureted engines can also be employed, possibly with more
accuracy, by using fuel injection. At least one major snowmobile
manufacturer currently employs electronic fuel injection on several of
its snowmobile models.
In addition to rich air-fuel ratios, one of the main reasons that
two-stroke engines have such high HC emission levels is that they
release a substantial amount of unburned fuel into the atmosphere as a
result from scavenging losses, as described above. One way to reduce or
eliminate such losses is to inject the fuel into the cylinder after the
exhaust port has closed. This can be done by injecting the fuel into
the cylinder through the transfer port (semi-direct injection) or
directly into the cylinder (direct injection). Both of these approaches
are currently being used successfully in two-stroke personal water
craft engines. We believe these technologies hold promise for
application to snowmobiles. In fact, one company is offering a
snowmobile with a semi-direct injection two-stroke engine for the 2003
model year. Manufacturers must address a variety of technical design
issues for adapting the technology to snowmobile operation, such as
operating in colder ambient temperatures and at variable altitude. The
averaging approach and the several years of lead time give
manufacturers time to incorporate these development efforts into their
overall research plan as they apply these technologies to snowmobiles.
In addition to the two-stroke technologies just discussed, using
four-stroke engines in snowmobiles is another feasible approach to
reduce emissions. Since they do not scavenge the exhaust gases with the
incoming air-fuel mixture, four-stroke engines have inherently lower HC
emissions compared to two-stroke engines. Four-stroke engines have a
lower power-to-displacement ratio than two-stroke engines and are
heavier. Thus, initially they may be more appropriate for snowmobile
models where extreme power and acceleration are not the primary selling
points. Such models include touring and sport trail sleds. However, one
company has developed a four-stroke engine based off one of their sport
highway motorcycle engines that produces 150 horsepower and will be
used in their high-performance snowmobiles in the 2003 model year.
c. What technologies are most likely to be used to meet emission
standards?
2006 Standards
We expect that, in the context of an emissions averaging program,
manufacturers might choose to take different paths to meet the 2006
emission standards. We expect manufacturers to use a mix of
technologies that will include improved carburetion and enleanment
strategies, combined with engine modifications, the use of direct
injection, and the use of four-stroke engine technology. For example,
depending on their emission rates, one scenario for meeting our
standards could be a mixture of 60 percent using improved carburetion,
enleanment strategies, and engine modifications, 15 percent using
direct injection, and another 15 percent using four-stroke engines.
Manufacturers can expect moderate emission reductions from engine
modifications and enleanment strategies. Most two-stroke snowmobile
engines are designed to operate with a rich air and fuel mixture, which
result in high levels of HC, CO, and PM. By reducing the amount of fuel
in the air and fuel mixture (i.e., enleanment), these emissions can be
reduced. Because manufacturers use the extra fuel in the air and fuel
mixture to help cool the engine, some modifications such as the use of
more robust materials, may be necessary. Manufacturers have indicated
to us that direct injection strategies can result in emission
reductions of 70 to 75 percent for HC and 50 to 70 percent for CO.
Certification results from 2000 model year outboard engines and
personal water craft (PWC) support such reductions. We believe that as
manufacturers learn to apply direct injection strategies they may
choose to implement those technologies on some of their more expensive
sleds and use less aggressive technologies, such as improved
carburetion and enleanment on their lower performance models.
It appears that the use of four-stroke engines in snowmobiles will
be more prevalent than we initially anticipated. For the 2003 model
year, all four of the major snowmobile manufacturers will offer a four-
stroke engine. Two manufacturers have already sold limited quantities
of their four-stroke snowmobiles in 2002. All of these engines will be
appearing in at least two different models and in some cases up to
three or four models. The size and design of these engines is quite
varied. All of the engines range in size from 650 cc to 1000 cc. There
are two cylinder and four cylinder engines, fuel injected and
carbureted, moderate horsepower and high horsepower. Manufacturers have
indicated that depending on their success, four-stroke engines will
play a large role in meeting our standards.
2010 Standards
As with the 2006 standards, we expect that manufacturers will use a
mix of technologies to meet our 2010 standards. To meet the 2010
standards, manufacturers will need to employ the use of advanced
technologies such as direct fuel-injection and four-stroke engines on a
larger portion of their production. As noted above, manufacturers are
beginning to introduce these technologies and will be gaining
experience with them over the next several years. Because we are
offering manufacturers the option to choose between two sets of
standards in 2010, the mixture of technologies will be very
manufacturer and engine family specific. For example, direct injection
typically reduces CO significantly but does not reduce HC to the same
extent as four-stroke engines. Engine families that manufacturers
believe will be most compatible with direct injection technology would
likely meet the 75 g/kW-hr HC and 200 g/kW-hr CO
[[Page 68285]]
standards. A potential scenario for meeting these standards could be a
mixture of 50 percent direct injection, 20 percent four-stroke engines,
and 30 percent with engine modifications. Engine families that
manufacturers believe will be more compatible with four-stroke
technology, which typically has superior HC emissions levels but do not
necessarily have exceptionally good CO performance, will likely meet
the 45 g/kW-hr HC and 275 g/kw-hr CO standards. Under either option, it
is possible that manufacturers will continue to sell two-stroke models
with lesser levels of technology. Manufacturers are likely to reduce
emissions where possible from at least a portion of the remaining two-
stroke engines through the use of engine modifications, calibration
optimization, and secondary air systems. In some cases this will be
necessary just to meet the FEL cap. A potential scenario for meeting
these standards could be a mixture of 70 percent four-stroke engines,
10 percent direct fuel injection, and 20 percent with engine
modifications.
IV. Permeation Emission Control
A. Overview
In the proposal we specified only exhaust emission controls for
recreational vehicles. However, several commenters raised the issue of
control of evaporative emissions related to permeation from fuel tanks
and fuel hoses. The commenters stated that work done by California ARB
on permeation emissions from plastic fuel tanks and rubber fuel line
hoses for various types of nonroad equipment as well as portable
plastic fuel containers raised a new emissions concern. Our own
investigation into the hydrocarbon emissions related to permeation of
fuel tanks and fuel hoses from recreational land-based and marine
applications supports the concerns raised by the commenters. Therefore,
on May 1, 2002, we reopened the comment period and requested comment on
possible approaches to regulating permeation emissions from
recreational vehicles. As a result of our investigations and the
comments received, we have determined that it is appropriate to
promulgate standards regulating permeation emissions from these
vehicles.
This section describes the provisions for 40 CFR part 1051, which
would apply only to recreational vehicle manufacturers. This section
also discusses test equipment and procedures (for anyone who tests fuel
tanks and hoses to show they meet emission standards) and general
compliance provisions.
We are adopting performance standards intended to reduce permeation
emissions from recreational vehicles. The standards, which apply to new
vehicles starting in 2008, are nominally based on manufacturers
reducing these permeation emissions from new vehicles by about 90
percent overall.\67\ We also recognize that there are many small
businesses that manufacture recreational vehicles. We are therefore
adopting several special compliance provisions to reduce the burden of
permeation emission regulations on small businesses. These special
provisions are the same as for the exhaust emission standards, as
applicable, and are discussed in Section III.E.
---------------------------------------------------------------------------
\67\ Estimated reductions in permeation are 95 percent when not
considering competition vehicles, which are exempt from the
standard.
---------------------------------------------------------------------------
B. Vehicles Covered by This Provision
We are adopting new permeation emission standards for new off-
highway motorcycles, all-terrain vehicles, and snowmobiles. These
provisions apply even if the recreational vehicle manufacturer
exercises the option to use an engine certified under another program
such as the small spark ignition requirements in 40 CFR part 90. These
standards would require these vehicle manufacturers to use low
permeability fuel tanks and hoses. We include vehicles and fuel systems
that are used in the United States, whether they are made domestically
or imported.
Even though snowmobiles do not usually experience year around use,
as is the case with ATVs and off-highway motorcycles, we are including
snowmobiles in this standard because it is common practice among
snowmobile owners to store their snowmobiles in the off-season with
fuel in the tank (typically half full to full tank). A fuel stabilizer
is typically added to the fuel to prevent gum, varnish, and rust from
occurring in the engine as a result of the fuel sitting in the fuel
tank and fuel system for an extended period of time; however, this does
not reduce permeation. Thus, snowmobiles experience fuel permeation
losses just like off-highway motorcycles and ATVs.
We are extending our basic nonroad exemptions to the engines and
vehicles covered by this rule. These include the testing exemption, the
manufacturer-owned exemption, the display exemption, and the national
security exemption. These exemptions are described in more detail under
Section VII.C. In addition, vehicles used solely for competition are
not considered to be nonroad vehicles, so they are exempt from meeting
the emission standards (but see discussion in Section III.C.1.a
regarding the voluntary program for certification of all off-highway
motorcycles).
C. Permeation Emission Standards
1. What Are the Emission Standards and Compliance Dates?
We are finalizing new standards that will require an 85-percent
reduction in plastic fuel tank permeation and a 95-percent reduction in
fuel system hose permeation from new recreational vehicles beginning in
2008. These standards and their implementation dates are presented in
Table IV.C-1. Section IV.D presents the test procedures associated with
these standards. Test temperatures are presented in Table IV.C-1
because they represent an important parameter in defining the emission
levels.
We will base the permeation standards on the inside surface areas
of the hoses and fuel tanks. We sought comment on whether the potential
permeation standards for fuel tanks should be expressed as grams per
gallon of fuel tank capacity per day or as grams per square meter of
inside surface area per day. Although volume is generally used to
characterize fuel tank emission rates, we base the standard on inside
surface area because permeation is a function of surface area. In
addition, the surface to volume ratio of a fuel tank changes with
capacity and geometry of the tank. Two similar shaped tanks of
different volumes or two different shaped tanks of the same volume
could have different g/gallon/day permeation rates even if they were
made of the same material and used the same emission-control
technology. Therefore, we believe that using a g/m\2\/day form of the
standard more accurately represents the emissions characteristics of a
fuel tank and minimizes complexity. This approach was supported by the
commenters.
[[Page 68286]]
Table IV.C-1.--Permeation Standards for Recreational Vehicles
----------------------------------------------------------------------------------------------------------------
Implementation
Emission component date Standard Test temperature
----------------------------------------------------------------------------------------------------------------
Fuel Tank Permeation................... 2008 1.5 g/m2/day............. 28 [deg]C (82 [deg]F)
Hose Permeation........................ 2008 15 g/m2/day.............. 23 [deg]C (73 [deg]F)
----------------------------------------------------------------------------------------------------------------
These standards are revised compared to the values we sought
comment on in the notice. In the reopening of the comment period, we
identified the need to accommodate variability and deterioration in
setting the fuel tank permeation standard. Since the notice, we have
received test information that suggests that a tank permeation standard
representing an 85 rather than a 95-percent reduction would fully
accommodate these factors. Nonetheless, we continue to believe that
manufacturers will target control technologies and strategies focused
on achieving reductions of 95 percent in production tanks. With regard
to the permeation standard for hoses, we have adjusted the standard
slightly to give the manufacturers more freedom in selecting their hose
material and to accommodate the fact that we selected a certification
test fuel based on a 10-percent ethanol blend, which would be prone to
greater permeation than straight gasoline.
Cost-effective technologies exist to significantly reduce
permeation emissions. Because essentially all of these vehicles use
high density polyethylene (HDPE) fuel tanks, manufacturers would be
able to choose from several technologies for providing a permeation
barrier in HDPE tanks. The use of metal fuel tanks would also meet the
standards, because metal tanks do not experience any permeation losses.
The hose permeation standard can be met using barrier hose technology
or through using low permeation automotive-type tubing. These
technologies are discussed in Section IV.F. The implementation dates
give manufacturers three to four years to comply. This will allow
manufacturers time to implement controls in their tanks and hoses in an
orderly business manner.
2. Will I Be Able to Average, Bank, or Trade Emissions Credits?
Averaging, banking, and trading (ABT) refers to the generation and
use of emission credits based on certified emission levels relative to
the standard. The general ABT concept is discussed in detail in Section
II.C.3. In many cases, an ABT program can improve technological
feasibility, provide manufacturers with additional product planning
flexibility, and reduce costs which allows us to consider emission
standards with the most appropriate level of stringency and lead time,
as well as providing an incentive for the early introduction of new
technology.
We are finalizing ABT for fuel tanks to facilitate the
implementation of the standard across a variety of tank designs which
include differences in wall thickness, tank geometry, material quality,
and pigment in plastic fuel tanks. To meet the standard on average,
manufacturers would be able to divide their fuel tanks into different
emission families and certify each of their emission families to a
different Family Emissions Level (FEL). The emission families would
include fuel tanks with similar characteristics, including wall
thickness, material used (including additives such as pigments,
plasticizers, and UV inhibitors), and the emission-control strategy
applied. The FELs would then be weighted by sales volume and fuel tank
inside surface area to determine the average level across a
manufacturer's total production. An additional benefit of a corporate-
average approach is that it provides an incentive for developing new
technology that can be used to achieve even larger emission reductions
or perhaps to achieve the same reduction at lower costs or to achieve
some reductions early.
Any manufacturer could choose to certify each of its evaporative
emission control families at levels which would meet the standard. Some
manufacturers may choose this approach as the could see it as less
complicated to implement.
We are also finalizing a voluntary program intended to give an
opportunity for manufacturers to prove out technologies earlier than
2008. Manufacturers will be able to use permeation control strategies
early, and even if they do not meet the standard, they can earn credit
through partial emission reduction that will give them more lead time
to meet the standard. This program will allow a manufacturer to certify
fuel tanks early to a less stringent standard and thereby delay the
fuel tank permeation standard. Therefore, a manufacturer can earn more
time to meet the 1.5 g/m\2\/day standard if they have an alternative
approach that will reduce permeation by a lesser amount earlier than
2008. Specifically, if a manufacturer certifies fuel tanks early to a
standard of 3.0 g/m\2\/day, they can delay the 1.5 g/m\2\/day standard
for these fuel tanks by 1 tank-year for every tank-year of early
certification. As an alternative, this delay could be applied to other
fuel tanks provided that these tanks have an equal or smaller inside
surface area and meet a level of 3.0 g/m\2\/day. As an example, suppose
a manufacturer were to sell 50 vehicles in 2006 and 75 vehicles in 2007
with fuel tanks that meet a level of 3.0 g/m\2\/day. This manufacturer
would then be able to sell 125 vehicles with fuel tanks that meet a
level of 3.0 g/m\2\/day in 2008 and later years. No uncontrolled tanks
could be sold after 2007. In addition to providing implementation
flexibility to manufacturers, this option, if used, would result in
additional and earlier emission reductions.
For hoses, we do not believe that ABT provisions would result in a
significant technological benefit to manufacturers. We believe that all
fuel hoses can meet the permeation standards using straight forward
technology as discussed in Section IV.F. From EPA's perspective,
including an ABT program in the rule creates a long-term administrative
burden that is not worth taking on since it does not provide the
industry with useful flexibility.
3. How Do I Certify My Products?
We are finalizing a certification process similar to our existing
program for other mobile sources. Manufacturers test representative
prototype designs and submit the emission data along with other
information to EPA in an application for a Certificate of Conformity.
As discussed in Section IV.D.3, we will allow manufacturers to certify
based on either design (for which there is already data) or by
conducting its own emissions testing. If we approve the application,
then the manufacturer's Certificate of Conformity allows the
manufacturer to produce and sell the vehicles described in the
application in the U.S.
Manufacturers certify their fuel systems by grouping them into
emission families that have similar emission characteristics. The
emission family definition is fundamental to the certification process
and to a large
[[Page 68287]]
degree determines the amount of testing required for certification. The
regulations include specific characteristics for grouping emission
families for each category of tanks and hoses. For fuel tanks, key
parameters include wall thickness, material used (including additives
such as pigments, plasticizers, and UV inhibitors), and the emission-
control strategy applied. For hoses, key parameters include material,
wall thickness, and emission-control strategy applied. To address a
manufacturer's unique product mix, we may approve using broader or
narrower engine families. The certification process for vehicle
permeation is similar as for the process for certifying engines (see
Section II.C.1).
4. What Durability Provisions Apply?
We are adopting several additional provisions to ensure that
emission controls will be effective throughout the life of the vehicle.
This section discusses these provisions for permeation from
recreational vehicles. More general certification and compliance
provisions, which apply across different vehicle categories, are
discussed in Sections II and VII, respectively.
a. How long do my vehicles have to comply? Manufacturers would be
required to build fuel systems that meet the emission standards over
each vehicle's useful life. For the permeation standards, we use the
same useful life as discussed in Section III.C.4.a for exhaust
emissions from recreational vehicle engines based on the belief that
fuel system components and engines are intended to have the same design
life. Further, we are applying the same warranty period for permeation
emission related components of the fuel system as for exhaust emission-
related components of the vehicle (See Section III.C.4.b).
b. How do I demonstrate emission durability? We are adopting
several additional provisions to ensure that emission controls will be
effective throughout the life of the vehicle. Vehicle manufacturers
must demonstrate that the permeation emission-control strategies will
last for the useful life of the vehicle. Any deterioration in
performance would have to be included in the family emissions limit.
This section discusses durability provisions for fuel tanks and hoses.
For plastic fuel tanks, we are specifying a preconditioning and
four durability steps that must be performed in conjunction with the
permeation testing for certification to the standard. These steps,
which include fuel soaking, slosh, pressure-vacuum cycling, temperature
cycling, and ultra-violet light exposure, are described in more detail
in Section IV.D.1. The purpose of these preconditioning steps is to
help demonstrate the durability of the fuel tank permeation control
under conditions that may occur in use. For fuel hoses, the only
preconditioning step that we are requiring is a fuel soak to ensure
that the permeation rate is stabilized prior to testing. Data from
before and after the durability tests would be used to determine
deterioration factors for the certified fuel tanks. The durability
factors would be applied to permeation test results to determine the
certification emission level of the fuel tank at full useful life. The
manufacturer would still be responsible for ensuring that the fuel tank
and hose meet the permeation standards throughout the useful life of
the vehicle.
We recognize that vehicle manufacturers will likely depend on
suppliers/vendors for treated tanks and fuel hoses. We believe that, in
addition to normal business practices, our testing requirements will
help assure that suppliers/vendors consistently meet the performance
specifications laid out in the certificate.
D. Testing Requirements
To obtain a certificate allowing sale of products meeting EPA
emission standards, manufacturers generally must show compliance with
such standards through emission testing. The test procedures for
determining permeation emissions from fuel tanks and hoses on
recreational vehicles are described below. This section also discusses
design-based certification as an alternative to performing specific
testing.
1. What Are the Test Procedures for Measuring Permeation Emissions From
Fuel Tanks?
Prior to testing the fuel tanks for permeation emissions, the fuel
tank must be preconditioned by allowing the tank to sit with fuel in it
until the hydrocarbon permeation rate has stabilized. Under this step,
the fuel tank must be filled with a 10-percent ethanol blend in
gasoline (E10), sealed, and soaked for 20 weeks at a temperature of 28
+/- 5[deg]C. Once the soak period has ended, the fuel tank is drained,
refilled with fresh fuel, and sealed. The permeation rate from fuel
tanks is measured at a temperature of 28 +/- 2[deg]C over a period of
at least 2 weeks. Consistent with good engineering judgment, a longer
period may be necessary for an accurate measurement for fuel tanks with
low permeation rates. Permeation loss is determined by measuring the
weight of the fuel tank before and after testing and taking the
difference. Once the mass change is determined it is divided by the
manufacturer provided tank surface area and the number of days of soak
to get the emission rate. As an option, permeation may be measured
using alternative methods that will provide equivalent or better
accuracy. Such methods include enclosure testing as described in 40 CFR
part 86. The fuel used for this testing will be a blend of 90-percent
gasoline and 10-percent ethanol. This fuel is consistent with the test
fuel used for highway evaporative emission testing.
To determine permeation emission deterioration factor, we are
specifying three durability tests: slosh testing, pressure-vacuum
cycling, and ultra-violet exposure. The purpose of these deterioration
tests is to help ensure that the technology is durable and the measured
emissions are representative of in-use permeation rates. For slosh
testing, the fuel tank is filled to 40-percent capacity with E10 fuel
and rocked for 1 million cycles. The pressure-vacuum testing contains
10,000 cycles from -0.5 to 2.0 psi. These two durability tests are
based on draft recommended SAE practice.\68\ The third durability test
is intended to assess potential impacts of UV sunlight (0.2 [mu]m--0.4
[mu]m) on the durability of the surface treatment. In this test, the
tank must be exposed to a UV light of at least 0.40 W-hr/m2 /min on the
tank surface for 15 hours per day for 30 days. Alternatively, it can be
exposed to direct natural sunlight for an equivalent period of time.
---------------------------------------------------------------------------
\68\ Draft SAE Information Report J1769, ``Test Protocol for
Evaluation of Long Term Permeation Barrier Durability on Non-
Metallic Fuel Tanks,'' (Docket A-2000-01, document IV-A-24).
---------------------------------------------------------------------------
We originally sought comment on applying the procedures in 49 CFR
part 173, appendix B, but upon further evaluation and receipt of
additional information found these inadequate for our purposes. The 49
CFR part 173 test procedure is designed for testing plastic receptacles
for transporting hazardous chemicals. This test focus on temperatures
and durability procedures that do not represent recreational vehicle
use.
2. What Are the Test Procedures for Measuring Permeation Emissions From
Fuel System Hoses?
The permeation rate of fuel from hoses would be measured at a
temperature of 23 +/- 2[deg]C using SAE
[[Page 68288]]
method J30\69\ with E10. The hose must be preconditioned with a fuel
soak to ensure that the permeation rate has stabilized. The fuel to be
used for this testing would be a blend of 90-percent gasoline and 10-
percent ethanol. This fuel is consistent with the test fuel used for
highway evaporative emission testing. Alternatively, for purposes of
submission of data at certification, permeation could be measured using
alternative equipment and procedures that provide equivalent results.
To use these alternative methods, manufacturers would have to apply to
us and demonstrate equivalence. Examples of alternative approaches that
we anticipate manufacturers may use are the recirculation technique
described in SAE J1737,\70\ enclosure-type testing such as in 40 CFR
part 86, or weight loss testing such as described in SAE J1527.\71\
---------------------------------------------------------------------------
\69\ SAE Recommended Practice J30, ``Fuel and Oil Hoses,'' June
1998, (Docket A-2000-01, document IV-A-92).
\70\ SAE Recommended Practice J1737, ``Test Procedure to
Determine the Hydrocarbon Losses from Fuel Tubes, Hoses, Fittings,
and Fuel Line Assemblies by Recirculation,''1997, (Docket A-2000-01,
document, IV-A-34).
\71\ SAE Recommended Practice J1527, ``Marine Fuel Hoses,''1993,
(Docket A-2000-01, document IV-A-19).
---------------------------------------------------------------------------
3. Can I Certify Based on Engineering Design Rather Than Through
Testing?
In general, test data would be required to certify fuel tanks and
hoses to the permeation standards. Test data could be carried over from
year to year for a given emission-control design. We do not believe the
cost of testing tanks and hose designs for permeation would be
burdensome especially given that the data could be carried over from
year to year, and that there is a good possibility that the broad
emission family concepts would lead to minimum testing. However, there
are some specific cases where we would allow certification based on
design. These special cases are discussed below.
We would consider a metal fuel tank to meet the design criteria for
a low permeation fuel tank because fuel does not permeate through
metal. However, we would not consider this design to be any more
effective than any other low permeation fuel tank for the purposes of
any sort of credit program. Although metal is impermeable, seals and
gaskets used on the fuel tank may not be. The design criteria for the
seals and gaskets would be that either they would not have a total
exposed surface area exceeding 1000 mm\2\, or the seals and gaskets
would have to be made of a material with a permeation rate of 10 g/
m\2\/day or less at 23[deg]C as measured under ASTM D814.\72\ A metal
fuel tank with seals that meet this design criteria would readily pass
the standard.
---------------------------------------------------------------------------
\72\ ASTM Standard Test Method D 814-95 (Reapproved 2000),
``Rubber Property--Vapor Transmission of Volatile Liquids,'' (Docket
A-2000-01, document IV-A-95).
---------------------------------------------------------------------------
Fuel hoses can be certified by design as being manufactured in
compliance with certain accepted SAE specifications. Specifically, a
fuel hose meeting the SAE J30 R11-A or R12 requirements could be
design-certified to the standard. In addition, fuel line meeting the
SAE J2260\73\ Category 1 requirements could be design-certified to the
standard. These fuel hoses and fuel line specifications are based on
15-percent methanol fuel and higher temperatures. We believe that fuel
hoses and lines that are tested and meet these requirements would also
meet our hose permeation standards because both are generally
acknowledged as representing more stringent test parameters. In the
future, if new SAE specifications are developed which are consistent
with our hose permeation standards, we would consider including hoses
meeting the new SAE requirements as being able to certify by design.
---------------------------------------------------------------------------
\73\ SAE Recommended Practice J2260, ``Nonmetallic Fuel System
Tubing with One or More Layers,''1996, (Docket A-2000-01, document
IV-A-18).
---------------------------------------------------------------------------
At certification, manufacturers will have to submit an engineering
analysis showing that the tank or hose designs will meet the standards
throughout their full useful life. The tanks and hoses will remain
subject to the emission standards throughout their useful lives. The
design criteria relate only to the issuance of a certificate.
E. Special Compliance Provisions
We believe that the permeation control requirements will be
relatively easy for small businesses to meet, given the relatively low
cost of the requirements and the availability of materials and
treatment support by outside vendors. Low permeation fuel hoses are
available from vendors today, and we would expect that surface
treatment would be applied through an outside company. However, to
minimize any additional burden these requirements may impose on small
manufacturers, we are implementing, where they are applicable to
permeation, the same options we proposed for the exhaust emission
standards. These options for small recreational vehicle manufacturers
are described in detail in Section III.E.
F. Technological Feasibility
We believe there are several strategies that manufacturers can use
to meet our permeation emission standards. This section gives an
overview of this technology. See Chapters 3 and 4 of the Final
Regulatory Support Document for more detail on the technology discussed
here.
1. Implementation Schedule
The permeation emission standards for fuel tanks become effective
in the 2008 model year. Several technologies are available that could
be used to meet this standard. Surface treatments to reduce tank
permeation are widely used today in other container applications, and
the technology and production facilities needed to conduct this process
exist. Selar is used by at least one portable fuel tank manufacturer
and has also been used in automotive applications. Plastic tanks with
coextruded barriers have been used in automotive applications for
years. However, fuel tanks used in recreational vehicles are primarily
(but not exclusively) high-density polyethylene tanks with no
permeation control. We received comments from manufacturers that they
would not be able to comply with permeation standards until 2008 or
2009. They stated that, especially for fuel tanks, they would need this
extra lead time to ensure that the useful life requirement can be met
on their products. At the same time, others commented that the
technology is already available and that the permeation standards
should apply in 2004. We believe it is appropriate to give
manufacturers until the 2008 model year for the fuel tank permeation
standards. Manufacturers will need lead time to allow for durability
testing and other development work associated with applying this
technology to recreational vehicles. This is especially true for
manufacturers or vendors who choose to set up their own sulfonation or
fluorination facilities in-house.
We believe that the low permeation hose technology can also be
applied in the 2008 time frame. A lower permeation fuel hose exists
today known as the SAE R9 hose that is as flexible as the SAE R7 hose
used in most recreational applications today. These SAE hose
specifications are contained in SAE J30 cited above. This hose would
meet our permeation standard on gasoline, but probably not on a 10-
percent ethanol blend. As noted in Chapter 4 of the Final Regulatory
Support Document, barrier materials typically used in R9 hose today may
have permeation rates 3 to 5 times
[[Page 68289]]
higher on a 10-percent ethanol blend than on straight gasoline.
However, there are several lower permeability barrier materials that
can be used in rubber hose that will comply with the hose permeation
requirement on a 10-percent ethanol blend and still be flexible enough
for use in recreational vehicles. This hose is available for automotive
applications at this time, but some lead time may be required to apply
these hoses to recreational vehicles if hose connection fitting changes
were required. For these reasons, we are implementing the hose
permeation standard on the same schedule as the tank permeation
standards.
2. Standard Levels
We have identified several strategies for reducing permeation
emissions from fuel tanks and hoses. We recognize that some of these
technologies may be more desirable than others for some manufacturers,
and we recognize that different strategies for equal emission
reductions may be better for different applications. A specific example
of technology that could be used to meet the fuel tank permeations
would be surface barrier treatments such as sulfonation or
fluorination. With these surface treatments, more than a 95-percent
reduction in permeation emissions from new fuel tanks is feasible.
However, variation in material tolerances and in-use deterioration can
reduce this effectiveness. Given the lead time for the standards,
manufacturers will be able to provide fuel tanks with consistent
material quality, and the surface treatment processes can be optimized
for a wide range of material qualities and additives such as pigments,
plasticizers, and UV inhibitors. We do not expect a large deterioration
in use; however, data on slosh testing suggest that some deterioration
may occur. To accommodate variability and deterioration, we are
finalizing a standard that represents about an 85-percent reduction in
permeation emissions from plastic fuel tanks. It is our expectation
that manufacturers will aim for a surface treatment effectiveness rate
as near to 100 percent a practical for new tanks. Therefore, even with
variability and deterioration in use, control rates are likely to
exceed 85 percent. Several materials are available today that could be
used as a low permeation barrier in rubber hoses. We present more
detail on these and other technological approaches below.
3. Technological Approaches
a. Fuel tanks. Blow molding is widely used for the manufacture of
small fuel tanks of recreational vehicles. Typically, blow molding is
performed by creating a hollow tube, known as a parison, by pushing
high-density polyethylene (HDPE) through an extruder with a screw. The
parison is then pinched in a mold and inflated with an inert gas. In
highway applications, non-permeable plastic fuel tanks are produced by
blow molding a layer of ethylene vinyl alcohol (EVOH) or nylon between
two layers of polyethylene. This process is called coextrusion and
requires at least five layers: the barrier layer, adhesive layers on
either side of the barrier layer, and HDPE as the outside layers which
make up most of the thickness of the fuel tank walls. However, multi-
layer construction requires two additional extruder screws which
significantly increases the cost of the blow molding process. Multi-
layer fuel tanks can also be formed using injection molding. In this
method, a low viscosity polymer is forced into a thin mold to create
each side of the fuel tank. The two sides are then welded together. To
add a barrier layer, a thin sheet of the barrier material is placed
inside the mold prior to injection of the poleythylene. The
polyethylene, which generally has a much lower melting point than the
barrier material, bonds with the barrier material to create a shell
with an inner liner.
A less expensive alternative to coextrusion is to blend a low
permeable resin in with the HDPE and extrude it with a single screw.
The trade name typically used for this permeation control strategy is
Selar. The low permeability resin, typically EVOH or nylon, creates
non-continuous platelets in the HDPE fuel tank which reduce permeation
by creating long, tortuous pathways that the hydrocarbon molecules must
navigate to pass through the fuel tank walls. Although the barrier is
not continuous, this strategy can still achieve greater than a 90-
percent reduction in permeation of gasoline. EVOH has much higher
permeation resistance to alcohol than nylon; therefore, it would be the
preferred material to use for meeting our standard which is based on
testing with a 10-percent ethanol fuel.
Another type of low permeation technology for fuel tanks would be
to treat the surfaces of a plastic fuel tanks with a barrier layer. Two
ways of achieving this are known as fluorination and sulfonation. The
fluorination process causes a chemical reaction where exposed hydrogen
atoms are replaced by larger fluorine atoms which creates a barrier on
the surface of the fuel tank. In this process, a batch of fuel tanks
are generally processed post production by stacking them in a steel
container. The container is then voided of air and flooded with
fluorine gas. By pulling a vacuum in the container, the fluorine gas is
forced into every crevice in the fuel tanks. As a result of this
process, both the inside and outside surfaces of the fuel tank would be
treated. As an alternative, fuel tanks can be fluorinated on-line by
exposing the inside surface of the fuel tank to fluorine during the
blow molding process. However, this method may not prove as effective
as off-line fluorination which treats the inside and outside surfaces.
Sulfonation is another surface treatment technology where sulfur
trioxide is used to create the barrier by reacting with the exposed
polyethylene to form sulfonic acid groups on the surface. Current
practices for sulfonation are to place fuel tanks on a small assembly
line and expose the inner surfaces to sulfur trioxide, then rinse with
a neutralizing agent. However, sulfonation can also be performed using
a batch method. Either of these processes can be used to reduce
gasoline permeation by more than 95 percent.
Over the first month or so of use, polyethylene fuel tanks can
expand by as much as three percent due to saturation of the plastic
with fuel. Manufacturers have raised the concern that this hydrocarbon
expansion could affect the effectiveness of surface treatments like
fluorination or sulfonation. We believe this will not have a
significant effect on the effectiveness of these surface treatments.
California ARB has performed extensive permeation testing on portable
fuel containers with and without these surface treatments. Prior to the
permeation testing, the tanks were prepared by first performing a
durability procedure where the fuel container is cycled a minimum of
1000 times between -1 psi and 5 psi. In addition, the fuel containers
are soaked with fuel for a minimum of four weeks prior to testing.
Their test data, presented in Chapter 4 of the Final Regulatory Support
Document show that fluorination and sulfonation are still effective
after this durability testing.
Manufacturers have also commented that fuel sloshing in the fuel
tank, under normal in-use operation, could wear off the surface
treatments. However, we do not believe that this is likely. These
surface treatments actually result in an atomic change in the structure
of the
[[Page 68290]]
outside surface of the fuel tank. To wear off the treatment, the
plastic would need to be worn away on the outside surface. In addition,
testing by California ARB shows that the fuel tank permeation standard
can be met by fuel tanks that have been sloshed for 1.2 million cycles.
Test data on an sulfonated automotive HDPE fuel tank after five years
of use showed no deterioration in the permeation barrier. This data are
presented in Chapter 4 of the Final Regulatory Support Document.
Permeation can also be reduced from fuel tanks by constructing them
out of a lower permeation material than HDPE. For instance, metal fuel
tanks would not permeate. In addition, there are grades of plastics
other than HDPE that could be molded into fuel tanks. One commenter
suggested nylon; however, although nylon has excellent permeation
resistance on gasoline, it has poor chemical resistance to alcohol-
blended fuels. Other materials, which have excellent permeation even
with alcohol-blended fuels are acetal copolymers and thermoplastic
polyesters. At this time, these materials are generally much more
expensive than HDPE.
b. Hoses. Fuel hoses produced for use in recreational vehicles are
generally extruded nitrile rubber with a cover for abrasion resistance.
Lower permeability fuel hoses produced today for other applications are
generally constructed in one of two ways: either with a low
permeability layer or by using a low permeability rubber blend. By
using hose with a low permeation thermoplastic layer, permeation
emissions can be reduced by more than 95 percent. Because the
thermoplastic layer is very thin, on the order of 0.1 to 0.2 mm, the
rubber hose retains its flexibility. Two thermoplastics which have
excellent permeation resistance, even with an alcohol-blend fuel, are
ETFE and THV.\74\
---------------------------------------------------------------------------
\74\ ethylene-tetrafluoro-ethylene (ETFE), tetra-fluoro-
ethylene, hexa-fluoro-propylene, and vinyledene fluoride (THV).
---------------------------------------------------------------------------
In automotive applications, multilayer plastic tubing, made of
fluoropolymers is generally used. An added benefit of these low
permeability lines is that some fluoropolymers can be made to conduct
electricity and therefore can prevent the buildup of static charges.
Although this technology can achieve more than an order of magnitude
lower permeation than barrier hoses, it is relatively inflexible and
may need to be molded in specific shapes for each recreational vehicle
design. Manufacturers have commented that they would need flexible hose
to fit their many designs, resist vibration, and to simplify the hose
connections and fittings.
An alternative approach to reducing the permeability of fuel hoses
would be to apply a surface treatment such as fluorination or
sulfonation. This process would be performed in a manner similar to
discussed above for fuel tanks.
4. Conclusions
The standards for permeation emissions from recreational vehicles
reasonably reflect what manufacturers can achieve through the
application of available technology. Manufacturers will have several
years of lead time to select, design, and produce permeation emission-
control strategies that will work best for their product lines. We
expect that meeting these requirements will pose a challenge, but one
that is feasible taking into consideration the availability and cost of
technology, lead time, noise, energy, and safety. The role of these
factors is presented in detail in Chapters 3 and 4 of the Final
Regulatory Support Document.
The permeation standards are based on the effective application of
low permeable materials or surface treatments. This is a step change in
technology; therefore, we believe that even if we set a less stringent
permeation standard, these technology options would likely still be
used. In addition, this technology is relatively inexpensive and can
achieve meaningful emission reductions. The standards are expected to
achieve more than an 85-percent reduction in permeation emissions from
fuel tanks and more than 95 percent from hoses. We believe that more
stringent standards could result in significantly more expensive
materials without corresponding additional emission reduction. In
addition, the control technology would generally pay for itself over
time by conserving fuel that would otherwise evaporate. The projected
costs and fuel savings are discussed in Chapter 5 of the Final
Regulatory Support Document.
V. Large Spark-Ignition (SI) Engines
A. Overview
This section applies to most nonroad spark-ignition engines rated
over 19 kW (``Large SI engines''). The emission standards will lead to
emission reductions of about 90 percent for CO, NOX, and HC.
Since the emission standards are based on engine testing with broadly
representative duty cycles, these estimated reductions apply to all
types of equipment using these engines. Reducing Large SI engine
emissions will help reduce ozone and CO concentrations and will also be
valuable to individuals operating these engines in areas with limited
fresh air circulation. The cost of applying the anticipated emission-
control technology to these engines is offset by much greater cost
savings from reduced fuel consumption over the engines' operating
lifetime, as described in the Final Regulatory Support Document.
This section describes the requirements that apply to engine
manufacturers. See Section II for a description of our general approach
to regulating nonroad engines and how manufacturers show that they meet
emission standards. See Section VII for additional requirements for
engine manufacturers, equipment manufacturers, and others. See Section
VIII for general provisions related to testing equipment and
procedures.
B. Large SI Engines Covered by This Rule
Large SI engines covered in this section power nonroad equipment
such as forklifts, sweepers, pumps, and generators. This includes
marine auxiliary engines, but does not include marine propulsion
engines or engines used in recreational vehicles (snowmobiles, off-
highway motorcycles, and all-terrain vehicles). These other nonroad
applications are addressed elsewhere in this document.
This final rule applies only to spark-ignition engines. Our most
recent rulemaking for nonroad diesel engines adopted a definition of
``compression-ignition'' that addressed the status of alternative-fuel
engines (63 FR 56968, October 23, 1998). We are adopting updated
definitions consistent with those already established in previous
rulemakings to clarify that all reciprocating internal combustion
engines are either spark-ignition or compression-ignition.\75\ These
new definitions apply to 40 CFR parts 89 and 1048. Spark-ignitions
include gasoline-fueled engines and any others that control power with
a throttle and follow the theoretical Otto cycle. Compression-ignition
engines are any reciprocating internal-combustion engines that are not
spark-ignition engines. Under these definitions, it is possible for a
diesel-derived engine to fall under the spark-ignition program. We
believe the requirements adopted in this rule are feasible and
appropriate for these engines. However, we will allow such engines over
250 kW to instead meet the requirements that apply to nonroad
[[Continued on page 68291]]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
]
[[pp. 68291-68340]]
Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
[[Continued from page 68290]]
[[Page 68291]]
diesel engines. We believe this is appropriate for several reasons.
First, the technology requirements are comparable between programs. The
nonroad diesel emission standards, which apply over the longer useful
life characteristic of diesel engines, are slightly more stringent for
CO and slightly less stringent for HC+NOX. The calibration
changes needed to adjust these emission levels are not fundamental to
the overall design of the emission-control system. Second, the diesel
engine manufacturers producing these engines are already set up to do
testing based on test procedures that apply to diesel engines. To the
extent that they would incur costs to be able to run test procedures
specified for Large SI engines, these costs would likely not correspond
with improving emission-controls. Third, these engines share important
technical characteristics with diesel engines and are likely to
experience in-use operation that is more like that of nonroad diesel
engines. In addition, they are installed in applications that also use
diesel engines, not Large SI engines.
---------------------------------------------------------------------------
\75\ Gas turbines are non-reciprocating internal combustion
engines.
---------------------------------------------------------------------------
Several types of engines are excluded or exempted from these new
regulations. The following sections describe the types of special
provisions that apply uniquely to nonrecreational spark-ignition
engines rated over 19 kW. Section VII.C covers several additional
exemptions that apply generally across programs.
1. Stationary Engine Exclusion
Consistent with the Clean Air Act, stationary-source engines are
not nonroad engines, so the emission standards don't apply to engines
used in stationary applications. In general, an engine that would
otherwise be considered a Large SI engine is not considered a nonroad
engine if it will be either installed in a fixed position or if it will
be a portable (or transportable) engine operating for at least one-year
periods without moving throughout its lifetime. We are adopting the
same definitions for these engines that have already been established
for other programs. These stationary engines (that would otherwise
qualify as Large SI engines) must have an engine label identifying
their excluded status. This is especially valuable for importing
excluded engines without complication from U.S. Customs officials. It
also helps us ensure that such engines are legitimately excluded from
emission standards.
2. Exclusion for Engines Used Solely for Competition
For Large SI engines we proposed the existing regulatory definition
for nonroad engines, with excludes engines used solely for competition.
As described in the proposed rule, we are not aware of any
manufacturers producing new engines that are intended only for
competition. As a result, we are not adopting any specific provisions
addressing a competition exclusion for manufacturers. Part 1068 of the
regulations includes provisions addressing the practice of modifying
certified engines for competition (see Section VII.C).
3. Motor Vehicle Engine Exemption
In some cases an engine manufacturer may want to modify a certified
automotive engine for nonroad use to sell the engine without
recertifying it as a Large SI engine. We are therefore adopting an
exemption from the Large SI standards in 40 CFR part 1048 for engines
that are already certified to the emission standards in 40 CFR part 86
for highway applications. To qualify for this exemption from separately
certifying to nonroad standards, the manufacturer must makes no changes
to the engine that might affect its exhaust or evaporative emissions.
Companies using this exemption must report annually to us, including a
list of its exempted engine models. For engines included under this
provision, manufacturers of the vehicle or engine must generally meet
all the requirements from 40 CFR part 86 that would apply if the engine
were used in a motor vehicle. Section 1048.605 of the regulations
describes the qualifying criteria and responsibilities in greater
detail.
We generally prohibit equipment or vehicle manufacturers from
producing new nonroad equipment that does not have engines certified to
nonroad emission standards. However, in some cases a manufacturer may
want to produce vehicles certified to highway emission standards for
nonroad use. We are providing an exemption for these manufacturers, as
long as there is no change in the vehicle's exhaust or evaporative
emission-control systems. For example, a mining company may want to use
a pickup truck for dedicated work at a mine site, but special-order the
trucks from the manufacturer with modifications that cause the truck to
no longer qualify as a motor vehicle. Manufacturers may produce such a
modified version of a truck that has been certified to the motor-
vehicle standards, as long as the modifications don't affect its
emissions.
4. Lawn and Garden Engine Exemption
Most Large SI engines, rated over 19 kW, have a total displacement
greater than one liter. The design and application of the few Large SI
engines currently being produced with displacement less than one liter
are very similar to those of engines rated below 19 kW, which are
typically used for lawn and garden applications. As described in the
most recent rulemaking for these smaller engines, manufacturers may
certify engines between 19 and 30 kW with total displacement of one
liter or less to the requirements we have already adopted in 40 CFR
part 90 for engines below 19 kW (see 65 FR 24268, April 25, 2000). We
are not changing this provision, and engines so certified would not be
subject to the requirements that apply to Large SI engines. This
approach allows manufacturers of small air-cooled engines to certify
their engines rated between 19 and 30 kW with the program adopted for
the comparable engines with slightly lower power ratings. This is also
consistent with the provisions adopted by California ARB, except for
the addition of the 30-kW cap to prevent treating high-power engines
under the program that applies to lawn and garden engines.
Technological, economic, and environmental issues associated with
the few engine models with rated power over 19 kW, but with
displacement at or below 1 liter, were previously analyzed in the
rulemaking for nonroad spark-ignition engines below 19 kW. This rule
therefore does not specifically address the provisions applying to them
or repeat the estimated impacts of adopting emission standards.
Conversely, we are aware that some engines rated below 19 kW may be
part of a larger family of engine models that includes engines rated
above 19 kW. This may include, for example, three- and four-cylinder
engine models that are otherwise identical. To avoid the need to
separate these engines into separate engine families (certified under
completely different control programs), manufacturers may certify any
engine rated under 19 kW to the more stringent Large SI emission
standards. Such an engine is then exempt from the requirements of 40
CFR part 90.
C. Emission Standards
In October 1998, California ARB adopted emission standards for
Large SI engines. We are extending these requirements to the rest of
the U.S. in the near term. We are also revising the
[[Page 68292]]
emission standards and adding various provisions in the long term, as
described below. The near-term and the long-term emission standards are
based on three-way catalytic converters with electronic fueling systems
to control emissions, and differ primarily in terms of how well the
controls are optimized. In addition to the anticipated emission
reductions, we project that these technologies will provide large
savings to operators as a result of reduced fuel consumption and other
performance improvements.
An important element of the control program is the attempted
harmonization with the requirements adopted by California ARB. We are
aware that inconsistent or conflicting requirements may lead to
additional costs. Cooperation between agencies has allowed a great
degree of harmonization. In addition to the common structure of the
programs, the specific provisions that make up the certification
requirements and compliance programs are consistent with very few
exceptions. In most of the cases where individual provisions differ,
the EPA language is more general than that adopted by California,
rather than being incompatible. The following sections describe the
requirements in greater detail.
1. What Are the Emission Standards and Compliance Dates?
a. Exhaust emissions. We are adopting standards starting in the
2004 model year consistent with those adopted by California ARB. These
standards, which apply to testing only with the applicable steady-state
duty cycles, are 4.0 g/kW-hr (3.0 g/hp-hr) for HC+NOX
emissions and 50 g/kW-hr (37 g/hp-hr) for CO emissions. See Section V.D
for further discussion of the steady-state duty cycles. We expect
manufacturers to meet these standards using three-way catalytic
converters and electronically controlled fuel systems. These systems
are similar to those used for many years in highway applications, but
not necessarily with the same degree of sophistication.
Adopting emission standards for these engines starting in 2004
allows a relatively short lead time. However, manufacturers will be
able to achieve this by expanding their production of the same engines
they will be selling in California at that time. We have designed our
2004 standards to require no additional development, design, or testing
beyond what California ARB already requires. Adopting these near-term
emission standards allows us to set early requirements to introduce the
low-emission technologies for substantial emission reductions with
minimal lead time. The final requirements includes two principal
adjustments to align with the California ARB standards. First, we
specify that manufacturers' deterioration factors for 2004 through 2006
model years should be based on emission measurements over 3500 hours of
engine operation, rather than the full useful life of 5000 hours.
Second, for those same model years, we are applying an emission
standard of 5.4 g/kW-hr (4.0 g/hp-hr) HC+NOX for any in-use
testing to account for the potential for additional deterioration
beyond 3500 hours. This allowance for higher in-use emissions is a
temporary provision to ensure the feasibility of compliance in the
early years of the program. Testing has shown that with additional
design time, manufacturers can incorporate emission-control
technologies with sufficient durability that the long-term standards do
not require a separate in-use standard. This is separate from the
field-testing standards described below.
Testing has shown that additional time to optimize designs to
better control emissions will allow manufacturers to meet significantly
more stringent emission standards that are based on more robust
measurement procedures. We are therefore adopting a second tier of
standards to require additional emission reductions. These later
standards require manufacturers to control emissions under both steady-
state and transient engine operation, as described in Section V.D
below). Setting the emission standards to require additional control
involves separate consideration of the achievable level of control for
HC+NOX and CO emissions. While HC+NOX emissions
contribute to nonattainment of ozone air quality standards, CO
emissions contribute to nonattainment of CO air quality standards and
potentially harmful exposures of individuals where engines are
operating in areas where fresh airflow may be restricted. Emission-
control technology is able to simultaneously control these three
pollutants, but a tradeoff between NOX and CO emissions
persists for any given system. This relationship is determined by an
engine's precise control of air-fuel ratios--shifting to air-fuel
ratios slightly lean of stoichiometric increases NOX
emissions but decreases CO emissions and vice versa. Engines using
different fuels face this same situation, though gasoline engines
operating under heavy load generally need to shift to richer air-fuel
ratios to prevent accelerated engines wear from very high combustion
temperatures.
Our primary focus in setting the level of the emission standards is
reductions in emissions that contribute to ambient air-pollution
problems. At the same time, we recognize that these engines are used in
many applications where there are concerns about personal exposure to
the engine exhaust, including workplace exposure, focusing primarily on
CO exposure. It is appropriate to take such concerns into consideration
in setting the level of the standards. In this case, where the
equipment using these engines can vary substantially and where the
emission-control technology means there is a trade-off between
HC+NOX control and CO control, it is difficult to set a
single, optimal standard for all three pollutants. In such a situation
it is reasonable to have more than one set of standards to allow an
engine to use technologies focused on controlling the pollutants of
most concern for a specific application.
We are not in a position, however, to readily identity the specific
levels of alternative standards that are appropriate for each
application or to pick specific applications that should go with
different standards. We also want to ensure that engines significantly
reduce emissions of all three pollutants.
To address this, we are setting a combination of standards
requiring more effective emission controls starting with the 2007 model
year. First, we are setting benchmark emission standards of 2.7 g/kW-hr
(2.0 g/hp-hr) for HC+NOX emissions and 4.4 g/kW-hr (3.3 g/
hp-hr) for CO emissions. The emission standards apply to measurements
during duty-cycle testing under both steady-state and transient
operation, including certification, production-line testing, and in-use
testing.\76\ These emission levels provide for substantial control of
HC+NOX emissions (in fact, these standards are more
stringent than those proposed), but also contain substantial control of
CO emissions to protect against individual exposure as well as CO
nonattainment.
---------------------------------------------------------------------------
\76\ See Section V.D for a discussion of duty cycles.
---------------------------------------------------------------------------
We are also including an option for manufacturers to certify their
engines to different emission levels to allow manufacturers to build
engines whose emission controls are more weighted toward controlling
NOX emissions to reflect the inherent tradeoff of
NOX and CO emissions. Generally this involves meeting a less
stringent CO standard if a manufacturer certifies an engine with lower
HC+NOX emissions. Table V.C-1 shows several examples of
possible combinations of HC+NOX and CO emission standards.
The highest allowable CO standard is 20.6 g/kW-hr (15.4 g/hp-hr), which
corresponds with HC+NOX emissions below 0.8 g/kW-hr
[[Page 68293]]
(0.6 g/hp-hr). Manufacturers certify to any HC+NOX level
between and including 0.8 and 2.7 g/kW-hr, rounding to the nearest 0.1
g/kW-hr. They will certify also to the corresponding CO level, as
calculated using the formula below, again rounding to the nearest 0.1
g/kW-hr.
Table V.C-1.--Samples of Possible Alternative Duty-Cycle Emission
Standards for Large SI Engines(g/kW-hr)*
------------------------------------------------------------------------
HC+NOX CO
------------------------------------------------------------------------
2.7.......................................................... 4.4
2.2.......................................................... 5.6
1.7.......................................................... 7.9
1.3.......................................................... 11.1
1.0.......................................................... 15.5
0.8.......................................................... 20.6
------------------------------------------------------------------------
* As described in the Final Regulatory Support Document and the
regulations, the values in the table are related by the following
formula: (HC+NOX) x CO0.784 = 8.57. These values follow directly from
the logarithmic relationship presented with the proposal in the Draft
Regulatory Support Document.
We believe this flexible approach to setting standards is the most
appropriate and efficient way to allocate the different design
strategies to achieve effective reductions of HC+NOX
emissions while providing for the best control of CO emissions where it
is most needed. Testing has shown that emission controls are more
likely to experience degradation with respect to controlling CO
emissions than HC or NOX emissions. Manufacturers therefore
have a natural incentive to certify engine families with an
HC+NOX emission level as low as possible to increase the
compliance margin for meeting the CO standard. In addition, many of
these engines will be used in applications where ozone is of more
concern. As a result, we expect manufacturers to design most of their
engines to operate substantially below the 2.7 g/kW-hr standard for
HC+NOX emissions. This approach also encourages
manufacturers to continually improve their control of HC+NOX
emissions over time. At the same time, to the extent that purchasers
want engines with low CO emission levels, particularly for exposure-
related concerns, manufacturers will be able to produce compliant
engines that will provide appropriate protection. Note that engines
operating at the highest allowable CO emission levels under the 2007
standards will still be substantially reducing CO emissions compared
with baseline levels. The emission standards in this final rule will
achieve substantial reductions, but are not designed to guarantee
workplace safety or to set a safety standard. Rather, we intend to
facilitate the use of engine-based control technologies so that owners
and operators can purchase equipment to help them address these
concerns.
We are not adopting any controls or limits to restrict the sale of
engines meeting certain requirements into certain applications. We
believe that the manufacturers and customers for these products will
together make educated choices regarding the appropriate mix of
emission controls for each application and that market forces will
properly balance emission controls for the different pollutants in
specific applications. We believe that customers for these
applications, some of whom are subject to occupational air-quality
standards for related pollutant concentrations, will be well placed to
make informed choices regarding air-pollution control, especially given
their ability to make choices based on the specific environmental
circumstances of each particular customer.\77\
---------------------------------------------------------------------------
\77\ While the emission standards in this final rule require
substantial emission reductions of CO and other harmful pollutants
from nonroad engines, this does not replace the need for ongoing
regulation of air quality to protect occupational safety and health.
More specifically, in accordance with the limitations provided in
Section 310(a) of the Clean Air Act (42 U.S.C. section 7610(a)),
nothing in this rule affects the Occupational Safety and Health
Administration's authority to enforce standards and other
requirements under the Occupational Safety and Health Act of 1970
(29 U.S.C. sections 651 et seq.).
---------------------------------------------------------------------------
We are adopting field-testing standards of 3.8 g/kW-hr (2.8 g/hp-
hr) for HC+NOX and 6.5 g/kW-hr (4.9 g/hp-hr) for CO. As
described above for duty-cycle testing, field-testing allows for the
same pattern of optional emission standards to reflect the tradeoff of
CO and NOX emissions. See Section V.D.5 for more information
about field testing.
As described in Chapter 4 of the Final Regulatory Support Document,
we believe manufacturers can achieve these emission standards by
optimizing currently available three-way catalysts and electronically
controlled fuel systems.
Two additional provisions apply to specific situations. First, some
engines need to operate with rich air-fuel ratios at high loads to
protect the engine from overheating. This is especially true for
gasoline-fueled engines, which typically experience higher combustion
temperatures. When operating at such air-fuel ratios, the engines may
be unable to meet the CO emission standard during steady-state testing
because the steady-state duty cycle involves sustained operation under
high-load conditions, unlike the transient duty cycle. If a
manufacturer shows us that this type of engine operation keeps it from
meeting the CO emission standard shown above for specific models, we
will approve a separate CO emission standard of 31.0 g/kW-hr that would
apply only to steady-state testing. This standard reflects the
adjustment needed at high-load operation and would apply to any steady-
state tests for certification, production-line testing, or in-use
testing. To prevent high in-use emission levels, we are adopting
several additional provisions related to this separate CO standard.
Manufacturers must show that enrichment is necessary to protect the
engine from damage and that enrichment will be limited to operating
modes that require additional cooling to protect the engine from
damage. In addition, manufacturers must show in their application for
certification that enrichment will rarely occur in the equipment in
which your engines are installed (for example, an engine that is
expected to operate 5 percent of the time in use with enrichment would
clearly not qualify). Finally, manufacturers must include in the
emission-related installation instructions any steps necessary for
someone installing the engines to prevent enrichment during normal
operation. This option does not apply to transient or field testing, so
these engines would need to meet the same formula for HC+NOX
and CO standards that apply to other engines for transient testing and
for field testing. By tying the CO standard for these engines to the
highest allowable CO emission level for field testing, we are
effectively requiring that manufacturers ensure that in-use engines
employ engine-protection strategies no more frequently than is
reflected in the steady-state duty cycles for certification.
Second, equipment manufacturers have made it clear that some
nonroad applications involve operation in severe environments that
require the use of air-cooled engines. These engines rely on air
movement instead of an automotive-style water-cooled radiator to
maintain acceptable engine temperatures. Since air cooling is less
effective, these engines rely substantially on enrichment to provide
additional cooling relative to water-cooled engines. At these richer
air-fuel ratios, catalysts are able to reduce NOX emissions
but oxidation of CO emissions is much less effective. As a result, we
are adopting emission standards for these ``severe-duty'' engines of
2.7 g/kW-hr for HC+NOX and 130 g/kW-hr for CO. These
standards apply to duty-cycle
[[Page 68294]]
emission testing for both steady-state and transient measurements (for
certification, production-line, and in-use testing). The corresponding
field-testing standards are 3.8 g/kW-hr for HC+NOX and 200
g/kW-hr for CO. Severe-duty applications include concrete saws and
concrete pumps. These types of equipment are exposed to high levels of
concrete dust, which tends to form a thick insulating coat around any
heat-exchanger surfaces and exposes engines to highly abrasive dust
particles. Manufacturers may request approval in identifying additional
severe-duty applications subject to these less stringent standards if
they can provide clear evidence that the majority of installations need
air-cooled engines as a result of operation in a severe-duty
environment. This arrangement generally prevents these higher-emitting
engines from gaining a competitive advantage in markets that don't
already use air-cooled engines.
We believe three years between phases of emission standards allows
manufacturers enough lead time to meet the more stringent emission
standards. The projected emission-control technologies for the 2004
emission standards should be capable of meeting the 2007 emission
levels with additional optimization and testing. In fact, manufacturers
may be able to apply their optimization efforts before 2004, leaving
only the additional testing demonstration for complying with the 2007
standards. The biggest part of the optimization effort may be related
to gaining assurance that engines will meet field-testing emission
standards described in Section V.D.5, since engines will not be
following a prescribed duty cycle.
For engines fueled by gasoline and liquefied petroleum gas (LPG),
we specify emission standards based on total hydrocarbon measurements,
while California ARB standards are based on nonmethane hydrocarbons. We
believe that switching to measurement based on total hydrocarbons
simplifies testing, especially for field testing of in-use engines with
portable devices (See Section V.D.5). To maintain consistency with
California ARB standards in the near term, we will allow manufacturers
to base their certification through 2006 on either nonmethane or total
hydrocarbons (see 40 CFR 1048.145). Methane emissions from controlled
engines operating on gasoline or LPG are about 0.1 g/kW-hr.
Operation of natural gas engines is very similar to that of LPG
engines, with one noteworthy exception. Since natural gas consists
primarily of methane, these engines have a much higher level of methane
in the exhaust. Methane generally does not contribute to ozone
formation, so it is often excluded from emission measurements. We have
therefore specified nonmethane hydrocarbon emissions for comparison
with the standard for natural gas engines. However, the emission
standards based on measuring emissions in the field depend on total
hydrocarbons. We are therefore adopting a NOX-only field-
testing standard for natural gas engines instead of a HC+NOX
standard. Since control of NOX emissions for natural gas
engines poses a significantly greater challenge than controlling
nonmethane hydrocarbons, duty-cycle testing provides adequate assurance
that these engines have sufficiently low hydrocarbon emission levels.
Manufacturers must show that they meet these duty-cycle standards for
certification and the engines remain subject to the nonmethane
hydrocarbon standard in-use when tested over the same duty-cycles.
b. Evaporative emissions. We are adopting requirements related to
evaporative and permeation emissions from gasoline-fueled Large SI
engines. For controlling diurnal emissions, we are adopting an emission
standard of 0.2 grams of hydrocarbon per gallon of fuel tank capacity
during a 24-hour period. In addition, we specify that manufacturers use
fuel lines meeting an industry standard for permeation-resistance.
Finally, we require that manufacturers take steps to prevent fuel from
boiling. We expect certification of manufacturers' equipment to be
design-based, as compared with conducting a full emission-measurement
program during certification. As such, meeting these evaporative
requirements is much more like meeting the requirements related to
controlling crankcase emissions and is therefore discussed in detail in
Section V.C.4 below.
2. May I Average, Bank, or Trade Emission Credits?
We are not including an averaging, banking, and trading program for
certifying engines. As described in Chapter 4 of the Final Regulatory
Support Document, we believe that manufacturers will generally be able
to rely on a relatively uniform application of emission-control
technology to meet emission standards. The standards were selected
based on the capabilities of all manufacturers to comply with all their
models without an emission-credit program. Moreover, overlaying an
emission-credit program on the flexible standards described above would
be highly impractical. If such a program could be devised it would need
to be very complex and would achieve little, if any, advantage to
manufacturers beyond the advantages already embodied in the flexible
approach we are adopting.
However, as an alternative to a program of calculating emission
credits for averaging, banking, and trading, we are adopting a simpler
approach of ``family banking'' to help manufacturers transition to new
emission standards (see 40 CFR 1048.145 of the regulations).
Manufacturers may certify an engine family early, which would allow
them to delay certification of smaller engine families. This would be
based on the actual sales of each engine family; this requires no
calculation or accounting of emission credits. The manufacturer would
have actual sales figures for the early family at the end of the
production year, which would yield a total number of allowable sales
for the engine family with delayed compliance. Manufacturers may
certify engines to the 2004 standards early, but this would provide
benefits only for complying with the 2004 standards. These ``credits''
would not apply to engines for meeting the 2007 standards.
3. Is EPA Adopting Voluntary Blue Sky Standards for These Engines?
We are adopting voluntary Blue Sky standards for Large SI engines.
We are setting a target of 0.8 g/kW-hr (0.6 g/hp-hr) HC+NOX
and 4.4 g/kW-hr (3.3 g/hp-hr) CO as a qualifying level for Blue Sky
Series engines. The corresponding field-testing standards for Blue Sky
Series engines are 1.1 g/kW-hr (0.8 g/hp-hr) HC+NOX and 6.6
g/kW-hr (4.9 g/hp-hr) CO. These voluntary standards are based on
achieving the maximum control of both HC+NOX and CO
emissions, as described in Section V.C.1. To achieve these emission
levels, manufacturers will need to apply significantly additional
technology beyond that required for the mandatory standards.
Manufacturers may start producing engines to these voluntary
standards immediately after this final rule becomes effective. In
addition, we are adopting interim voluntary standards corresponding
with the introduction of new emission standards. Since manufacturers
will not be complying early to bank emission credits, voluntary
emission standards are an appropriate way to encourage manufacturers to
meet emission standards before the regulatory deadline. If
manufacturers certify engines to these voluntary standards, they are
not eligible for participation in the family-banking program described
[[Page 68295]]
above. In the 2003 model year, manufacturers may certify their engines
to the requirements that apply starting in 2004 to qualify for the Blue
Sky designation. Since manufacturers are producing engines with
emission-control technologies starting in 2001, these engines are
available to customers outside of California desiring emission
reductions or fuel-economy improvements. Similarly, for 2003 through
2006 model years, manufacturers may certify their engines to the
requirements that start to apply in 2007.
4. Are There Other Requirements for Large SI Engines?
a. Crankcase emissions. Due to blowby of combustion gases and the
reciprocating action of the piston, exhaust emissions (mostly
hydrocarbons) can accumulate in the crankcase. These crankcase
emissions are significant, representing about 33 percent of total
exhaust hydrocarbon. Uncontrolled engines route these vapors directly
to the atmosphere. We have long required that automotive engines
prevent crankcase emissions. Manufacturers typically do this by routing
crankcase vapors through a valve into the engine's air intake system
where they are burned in the combustion process.
Manufacturers may choose one of two methods for controlling
crankcase emissions. First, adding positive-crankcase ventilation
prevents crankcase emissions. Since automotive engine blocks are
already tooled for closed crankcases, the cost of adding a valve for
positive-crankcase ventilation for most engines is very small. An
alternative method addresses specific concerns related to turbocharged
engines or engines operating in severe-duty environments. Where closed
crankcases are impractical, manufacturers may therefore measure
crankcase emissions during any emission testing to add crankcase
emissions to measured exhaust emissions for comparing with the
standards.
b. Diagnosing malfunctions. Manufacturers must design their Large
SI engines to diagnose malfunctioning emission-control systems starting
with the 2007 model year (see Sec. 1048.110). Three-way catalyst
systems with closed-loop fueling control work well only when the air-
fuel ratios are controlled to stay within a narrow range around
stoichiometry.\78\ Worn or broken components or drifting calibrations
over time can prevent an engine from operating within the specified
range. This increases emissions and can significantly increase fuel
consumption and engine wear. The operator may or may not notice the
change in the way the engine operates. We are not requiring similar
diagnostic controls for recreational vehicles or recreational marine
diesel engines, because the anticipated emission-control technologies
for these other applications are generally less susceptible to drift
and gradual deterioration.
---------------------------------------------------------------------------
\78\ Stoichiometry is the proportion of a mixture of air and
fuel such that the fuel is fully oxidized with no remaining oxygen.
For example, stoichiometric combustion in gasoline engines typically
occurs at an air-fuel mass ratio of about 14.7.
---------------------------------------------------------------------------
This diagnostic requirement focuses solely on maintaining
stoichiometric control of air-fuel ratios. This kind of design detects
problems such as broken oxygen sensors, leaking exhaust pipes, fuel
deposits, and other things that require maintenance to keep the engine
at the proper air-fuel ratio.
Some companies are already producing engines with diagnostic
systems that check for consistent air-fuel ratios. Their initiative
supports the idea that diagnostic monitoring provides a mechanism to
help keep engines tuned to operate properly, with benefits for both
controlling emissions and maintaining optimal performance. There are
currently no inspection and maintenance programs for nonroad engines,
so the most important variable in making the emission control and
diagnostic systems effective is in getting operators to repair the
engine when the diagnostic light comes on. This calls for a relatively
simple design to avoid the signaling of false failures as much as
possible. The diagnostic requirements in this rule therefore focus on
detecting inappropriate air-fuel ratios, which is the most likely
failure mode for three-way catalyst systems. The malfunction-indicator
light must go on when an engine runs for a full minute under closed-
loop operation without reaching a stoichiometric air-fuel ratio.
Some natural gas engines may meet standards with lean-burn designs
that never approach stoichiometric combustion. While manufacturers may
design these engines to operate at specific air-fuel ratios, catalyst
conversion (with two-way catalysts) would not be as sensitive to air-
fuel ratio as with stoichiometric designs. For these or other engines
that rely on emission-control technologies incompatible with the
diagnostic system described above, manufacturers must devise an
alternate system that alerts the operator to engine malfunctions that
would prevent the emission-control system from functioning properly.
The automotive industry has developed a standardized protocol for
diagnostic systems, including hardware specifications, and uniform
trouble codes. In the regulations we reference standards adopted by the
International Organization for Standardization (ISO) for automotive
systems. If manufacturers find that these standards are not applicable
to the simpler diagnostic design specified for Large SI engines, we
encourage engine manufacturers to cooperate with each other and with
other interested companies to develop new standards specific to nonroad
engines. Manufacturers may request approval to use systems that don't
meet the automotive specifications if those specifications are not
practical or appropriate for their engines.
c. Evaporative emissions. Evaporative emissions occur when fuel
evaporates and is vented into the atmosphere. They can occur while an
engine or vehicle is operating and even while it is not being operated.
Among the factors that affect evaporative emissions are:
. Fuel metering (fuel injectors or carburetor)
. The degree to which fuel permeates fuel lines and fuel tanks
. Proximity of the fuel tank to the exhaust system or other heat
sources
. Whether the fuel system is sealed and the pressure at which
fuel vapors are ventilated.
In addition, some gasoline fuel tanks may be exposed to heat from
the engine compartment and high-temperature surfaces such as the
exhaust pipe. In extreme cases, fuel can start boiling, producing very
large amounts of gasoline vapors vented directly to the atmosphere.
Evaporative emissions from Large SI engines and the associated
equipment represent a significant part of their overall hydrocarbon
emissions. The magnitude of evaporative emissions varies widely
depending on the engine design and application. LPG-fueled equipment
generally has very low evaporative emissions because of the tightly
sealed fuel system. At the other extreme, carbureted gasoline-fueled
equipment can have high rates of evaporation. In 1998, Southwest
Research Institute measured emissions from several gasoline-fueled
Large SI engines and found them to vary from about 12 g/day up to
almost 100 g/day.\79\
[[Page 68296]]
This study did not take into account the possibility of unusually high
fuel temperatures during engine operation, as described further below.
---------------------------------------------------------------------------
\79\ ''Measurement of Evaporative Emissions from Off-Road
Equipment,'' by James N. Carroll and Jeff J. White, Southwest
Research Institute (SwRI 08-1076), November 1998, Docket A-2000-01,
document II-A-10.
---------------------------------------------------------------------------
We are adopting basic measures to reduce evaporative emissions from
gasoline-fueled Large SI engines. First, we are adopting an evaporative
emission standard of 0.2 grams per gallon of fuel tank capacity for 24-
hour day when temperatures cycle between 72[deg]
and 96[deg]
F. For
purposes of certification, manufacturers may choose, however, to rely
on a specific design for certification instead of measuring emissions.
We have identified a technology that adequately prevents evaporative
emissions such that the design itself would be enough to show
compliance with the evaporative emission standard for purposes of
certification. Specifically, pressurized fuel tanks control evaporative
emissions by suppressing vapor generation. In its standards for
industrial trucks operating in certain environments, Underwriters
Laboratories requires that trucks use self-closing fuel caps with tanks
that stay sealed to prevent evaporative losses; venting is allowed for
positive pressures above 3.5 psi or for vacuum pressures of at least
1.5 psi.\80\ We know that any Large SI engines or vehicles operating
with these pressures would meet the standard because test data confirm
the basic chemistry principles related to phase-change pressure
relationships showing that fuel tanks will remain sealed at all times
during the prescribed test procedure. Also, similar to the Underwriters
Laboratories' requirement, we specify that manufacturers must use self-
closing or tethered fuel caps to ensure that fuel tanks designed to
hold pressure are not inadvertently left exposed to the atmosphere.
---------------------------------------------------------------------------
\80\ ''Industrial Trucks, Internal Combustion Engine-Powered,''
UL558, ninth edition, June 28, 1996, paragraphs 26.1 through 26.4,
Docket A-2000-01, document II-A-28. See Section XI.I for our
consideration of incorporating the UL requirements into our
regulations by reference.
---------------------------------------------------------------------------
In some applications, manufacturers may want to avoid high fuel-
tank pressures. Manufacturers may be able to meet the standard using an
air bladder inside the fuel tank that changes in volume to keep the
system in equilibrium at atmospheric pressure.\81\ We have data showing
that these systems also would remain sealed at all times during the
prescribed test procedure. However, the permeation levels related to
the air bladder and the long-term durability of this type of system are
still unknown. Once these parameters are established with test data,
perhaps with some additional product development, this technology may
then qualify as an option for design-based certification. Similarly,
collapsible bladder tanks, which change in volume to prevent generation
of a vapor space or vapor emissions, may eventually be available as a
technology for design-based certification once permeation data are
available to confirm that systems with these tanks would meet the
standard. Finally, an automotive-type system that stores fuel tank
vapors for burning in the engine would be another alternative
technology, though it is unlikely that such a system can be simply
characterized and included as an option for design-based certification.
---------------------------------------------------------------------------
\81\ ''New Evaporative Control System for Gasoline Tanks,'' EPA
Memorandum from Charles Moulis to Glenn Passavant, March 1, 2001,
Docket A-2000-01, document II-B-16.
---------------------------------------------------------------------------
In addition, engine manufacturers must use (or specify that
equipment manufacturers installing their engines use) fuel lines
meeting the industry performance standard for permeation-resistant fuel
lines developed for motor vehicles.\82\ While metal fuel lines do not
have problems with permeation, manufacturers should use discretion in
selecting materials for grommets and valves connecting metal components
to avoid high-permeation materials. Evaporative emission standards for
motor vehicles have led to the development of a wide variety of
permeation-resistant polymer components. These permeation requirements
are based on manufacturers using a more effective emission controls
than that specified for recreational vehicles. This is appropriate
because Large SI manufacturers are able to use automotive-grade
materials across their product line, while recreational vehicle
manufacturers have pointed out various limitations in incorporating
automotive-grade materials. Conversely, Large SI manufacturers are not
subject to permeation requirements related to fuel tanks, since almost
all of these tanks are made of metal.
---------------------------------------------------------------------------
\82\ SAE J2260 ``Nonmetallic Fuel System Tubing with One or More
Layers,'' November 1996 (Docket A-2000-01, document II-A-03).
---------------------------------------------------------------------------
Finally, based on available technologies, manufacturers must take
steps to prevent fuel boiling. The Underwriters Laboratories
specification for forklifts attempts to address this concern through a
specified maximum fuel temperature, but the current limit does not
prevent fuel boiling.\83\ We are adopting a standard that prohibits
fuel boiling during continuous operation at 30[deg]
C (86[deg]
F).
Engine manufacturers must incorporate designs that reduce the heat load
to the fuel tank to prevent boiling. For companies that sell loose
engines, this may involve instructions to equipment manufacturers to
help ensure, for example, that fuel tank surfaces are exposed to
ambient air rather than to exhaust pipes or direct engine heat. Engine
manufacturers may specify a maximum fuel temperature for the final
installation. Such a temperature limit should be well below 53[deg]
C
(128[deg]
F), the temperature at which summer-grade gasoline (9 RVP)
typically starts boiling.
---------------------------------------------------------------------------
\83\ UL558, paragraph 19.1.1, Docket A-2000-01, document II-A-
28.
---------------------------------------------------------------------------
An additional source of evaporative emissions is from carburetors.
Carburetors often have high hot soak emissions (immediately after
engine shutdown). We expect manufacturers to convert carbureted designs
to fuel injection as a result of the exhaust emission standards. While
we do not mandate this technology, we believe the need to reduce
exhaust emissions will cause engine manufacturers to use fuel injection
on all gasoline engines. This change alone will eliminate most hot soak
emissions.
Engine manufacturers using design-based certification need to
describe in the application for certification the selected design
measures and specifications to address evaporative losses from
gasoline-fueled engines. For loose-engine sales, this includes
emission-related installation instructions that the engine manufacturer
gives to equipment manufacturers. While equipment manufacturers must
follow these installation instruction, the engine manufacturer has the
responsibility to certify a system that meets the evaporative-related
requirements described in this section. This should work in practice,
because engine manufacturers already provide equipment manufacturers a
variety of specifications and other instructions to ensure that engines
operate properly in-use after installation in the equipment. The
alternative approach of requiring equipment manufacturers to certify is
impractical because of the very large number of companies involved.
5. What Durability Provisions Apply?
a. Useful life. We are adopting a useful life period of seven years
or until the engine accumulates at least 5,000 operating hours,
whichever comes first. This figure represents a minimum value and may
increase as a result of data showing that an engine model is designed
to last longer. This figure,
[[Page 68297]]
which California ARB has already adopted, represents an operating
period that is common for Large SI engines before they undergo rebuild.
This also reflects a comparable degree of operation relative to the
useful life values of 100,000 to 150,000 miles that apply to automotive
engines (assuming an average driving speed of 20 to 30 miles per hour).
Some engines are designed for operation in severe-duty applications
with a shorter expected lifetime. Concrete saws in particular undergo
accelerated wear as a result of operating in an environment with high
concentrations of highly abrasive, airborne concrete dust particles. We
are allowing manufacturers to request a shorter useful life for an
engine family based on information showing that engines in the family
rarely operate beyond the alternative useful-life period. For example,
if engines powering concrete saws are typically scrapped after 2000
hours of operation, this would form the basis for establishing a
shorter useful-life period for those engines.
Manufacturers relying on design-based certification to meet the
evaporative requirements must use good engineering judgment to show
that emission controls will work for at least seven years. This may,
for example, be based on warranty or product-performance history from
component suppliers. This also applies for systems designed to address
crankcase emissions.
b. Warranty. Manufacturers must provide an emission-related
warranty for at least the first half of an engine's useful life (in
operating hours) or three years, whichever comes first. These periods
must be longer if the manufacturer offers a longer mechanical warranty
for the engine or any of its components; this includes extended
warranties that are available for an extra price. The emission-related
warranty includes components related to controlling evaporative and
crankcase emissions. In addition, we are adopting the warranty
provisions adopted by California ARB for high-cost parts. For emission-
related components whose replacement cost is more than about $400, we
specify a minimum warranty period of at least 70 percent of the
engine's useful life (in operating hours) or 5 years, whichever comes
first. See Sec. 1048.120 for a description of which components are
emission-related.
c. Maintenance instructions. We are specifying minimum maintenance
intervals much like those established by California ARB for Large SI
engines. The minimum intervals define how much maintenance a
manufacturer may specify to ensure that engines are properly maintained
for staying within emission standards. Manufacturers may schedule
maintenance on catalysts, fuel injectors, electronic control units and
turbochargers after 5,000 hours. For oxygen sensors and cleaning of
fuel-system components, the minimum maintenance interval is 2,500
hours. This fuel-system cleaning must be limited to steps that can be
taken without disassembling components. We have relaxed this from the
proposed interval of 4,500 hours to take into account comments
emphasizing that these maintenance steps will be necessary more
frequently than the proposed interval; this shorter interval also
reflects the comparable provisions that apply to automotive systems.
We are also proposing a diagnostic requirement to ensure that
prematurely failing oxygen sensors or other components are detected and
replaced on an as-needed basis. If operators fail to address faulty
components after a fault signal, we would not consider that engine to
be properly maintained. This could the engine ineligible for
manufacturer in-use testing.
d. Deterioration factors. We are adopting an approach that gives
manufacturers wide discretion in how to establish deterioration factors
for Large SI engines. The general expectation is that manufacturers
will rely on emission measurements from engines that have operated for
an extended period, either in field service or in the laboratory. The
manufacturer should do testing as needed to be confident that their
engines will meet emission standards under the in-use testing program.
In deciding to certify an engine family, we can review deterioration
factors to ensure that the projected deterioration accurately predicts
in-use deterioration. We will use results under the in-use testing
program to verify the appropriateness of deterioration factors.
In the first two or three years of certification, manufacturers
will not yet have data from the in-use testing program. Moreover,
manufacturers may choose to rely on technologies and calibrations for
meeting the long-term standards well before 2007 to simplify their
product-development efforts. We are therefore allowing manufacturers to
rely on an assigned deterioration factor to meet the 2004 standards,
while continuing to require manufacturers to meet the applicable
emission standards throughout the useful life for these engines. The
assigned deterioration factor may be derived from any available data
that would help predict the way these systems would perform in the
field, using good engineering judgment.
Manufacturers may develop deterioration factors for crankcase and
evaporative controls. However, we do not expect these control
technologies to experience degradation that would cause a deterioration
factor to be appropriate.
e. In-use fuel quality. Gasoline used in industrial applications is
generally the same as that used for automotive applications.
Improvements that have been made to highway-grade gasoline therefore
carry over directly to nonroad markets. This helps manufacturers be
sure that fuel quality will not degrade an engine's emission-control
performance after several years of sustained operation.
In contrast, there are no enforceable industry or government
standards for LPG fuel quality. Testing data indicate that varying fuel
quality has a small direct effect on emissions from a closed-loop
engine with a catalyst. The greater concern is that fuel impurities and
heavy-end hydrocarbons may cause an accumulation of deposits that can
prevent an emission-control system from functioning properly. While an
engine's feedback controls can compensate for some restriction in air-
and fuel-flow, deposits may eventually prevent the engine from
accurately controlling air-fuel ratios at stoichiometry. As described
in the Final Regulatory Support Document, test data show that emission-
control systems can tolerate substantial fuel-related deposits before
there is any measurable effect on emissions. Moreover, the engine
diagnostic systems described in the next section will notify the
operator when fuel-related deposits prevent an engine from operating at
stoichiometry. In any case, a routine cleaning step should remove
deposits and restore the engine to proper functioning.
Data from in-use testing will provide additional information
related to the effects of varying fuel quality on emission levels. This
information will be helpful in making sure that the deterioration
factors for certifying engines accurately reflect the whole range of
in-use operating variables, including varying fuel quality. Our testing
shows that fuel properties of conventional commercial LPG fuel allow
for durable, long-term control of emissions. However, to the extent
that engines operating in specific areas have inferior fuel quality
that prevents them from meeting emission standards, we will be pursuing
nationwide requirements to set minimum quality standards for in-use LPG
fuel.
[[Page 68298]]
D. Testing Requirements and Supplemental Emission Standards
1. What Duty Cycles Are Used To Measure Emissions?
For 2004 through 2006 model years, we specify the same steady-state
duty cycles adopted by California ARB. For variable-speed engines, this
involves the testing based on the ISO C2 duty cycle, which has five
modes at various intermediate speed points, plus one mode at rated
speed and one idle mode. The combined intermediate-speed points at 10,
25, and 50 percent account for over 70 percent of the total modal
weighting. A separate duty cycle for the large number of Large SI
engine providing power for constant-speed applications, such as
generators, welders, compressors, pumps, sweepers, and aerial lifts.
Constant-speed testing is based on the ISO D2 duty cycle, which
specifies engine operation at rated speed with five different load
points. This same steady-state duty cycle applies to constant-speed,
nonroad diesel engines. Emission values measured on the D2 duty cycle
are treated the same as values from the C2 duty cycle; the same
numerical standards apply to both cycles.
Manufacturers must generally test engines on both the C2 and D2
duty cycles. Since the C2 cycle includes very little operation at rated
speed, it is not effective in ensuring control of emissions for
constant-speed engines. The D2 cycle is even less capable of predicting
emission performance from variable-speed engines. Manufacturers may,
however, choose to certify their engines on only one of these two
steady-state duty cycles. In this case, they would need to take steps
to make sure C2-certified engines are installed only in variable-speed
applications and D2-certified engines are installed only in constant-
speed applications. Engine manufacturers would do this by labeling
their engines appropriately and providing installation instructions to
make sure equipment manufacturers and others are aware of the
restricted certification. Equipment manufacturers are required under
the regulations to follow the engine manufacturer's emission-related
installation instructions.
Starting in 2007, we specify an expanded set of duty cycles, again
with separate treatment for variable-speed and constant-speed
applications. The test procedure is comprised of three segments: (1) A
warm-up segment, (2) a transient segment, and (3) a steady-state
segment. Each of these segments, described briefly in this section,
include specifications for the speed and load of the engine as a
function of time. Measured emissions during the transient and steady-
state segments must meet the same emission standards that apply to all
duty cycles. In general, the duty cycles are intended to represent
operation from the wide variety of in-use applications. This includes
highly transient low-speed forklift operation, constant-speed operation
of portable equipment, and intermediate-speed vehicle operation.
Ambient temperatures in the laboratory must be between 20[deg]
and
30[deg]
C (68[deg]
and 86[deg] F) during duty-cycle testing. This
improves the repeatability of emission measurements when the engine
runs through its prescribed operation. We nevertheless expect
manufacturers to design for controlling emissions under broader ambient
conditions, as described in Section V.D.5.
The warm-up segment begins with a cold-start. This means that the
engine should be near room temperature before the test cycle begins.
(Starting with an engine that is still warm from previous testing is
allowed if good engineering judgment indicates that this will not
affect emissions.) Once the engine is started, it operates over the
first 3 minutes of the specified transient duty cycle without emission
measurement. The engine then idles for 30 seconds before starting the
prescribed transient cycle. The purpose of the warm-up segment is to
bring the engine up to normal operating temperature in a standardized
way. For severe-duty engines, the warm-up period is extended up to 15
minutes to account for the additional time needed to stabilize
operating temperatures from air-cooled engines. The warm-up period
allows enough time for engine-out emissions to stabilize, for the
catalyst to warm up enough to become active, and for the engine to
start closed-loop operation. This serves as a defined and achievable
target for the design engineer to limit cold-start emissions to a
relatively short period. In addition, we require manufacturers to
activate emission-control systems as soon as possible after engine
starting to make clear that it is not acceptable to design the
emission-control system to start working only after the defined warm-up
period is complete. In addition, we may measure emissions during the
warm-up period to evaluate whether manufacturers are employing defeat
devices. In contrast, transient testing of heavy-duty highway engines
requires separate cold-start and hot-start measurements, with an 86-
percent weighting assigned to the hot-start portion in calculating an
engine's composite emission level. We believe this approach for nonroad
engines serves to limit cold-start emissions without forcing
manufacturers to focus design and testing resources on this portion of
operation.
The transient segment of the general duty cycle is a composite of
forklift and welder operation. This duty cycle was developed by
selecting segments of measured engine operation from two forklifts and
a welder as they performed their normal functions. This transient
segment captures the wide variety of operation from a large majority of
Large SI engines as fork-lifts and constant-speed engines represent
about 90 percent of the Large SI market. Emissions measured during this
segment are averaged over the entire transient segment to give a single
value in g/kW.
Steady-state testing consists of engine operation for an extended
period at several discrete speed-load combinations. Associated with
these test points are weighting factors that allow a single weighted-
average steady-state emission level in g/kW. While any steady-state
duty cycle is limited in how much it can represent operation of engines
that undergo transient operation, the distribution of the C2 modes and
their weighting values aligns significantly with expected and measured
engine operation from Large SI engines. In particular, these engines
are generally not designed to operate for extended periods at high-
load, rated speed conditions. Field measurement of engine operation
shows, however, that forklifts operate extensively at lower speeds than
those included in the C2 duty cycle. While we believe the test points
of the C2 duty cycle are representative of engine operation from many
applications of Large SI engines, supplementing the steady-state
testing with a transient duty cycle is necessary to adequately include
engine operation characteristic of what occurs in the field.
A separate transient duty cycle applies to engines that are
certified for constant-speed applications only. These engines maintain
a constant speed, but can experience widely varying loads. The
transient duty cycle for these engines includes 20 minutes of engine
operation based on the way engines work in a welder. Note that
manufacturers selling engines for both constant-speed and variable-
speed applications may omit the constant-speed transient test, since
that type of operation is included in the general transient test.
A subset of constant-speed engines are designed to operate only at
high
[[Page 68299]]
load. To address the operating limitations of these engines, we are
adopting a modified steady-state duty cycle if the manufacturer
provides clear evidence showing that engines rarely operate below 75
percent of full load at rated speed. Since most Large SI engines are
clearly capable of operating for extended periods at light loads, we
expect these provisions to apply to very few engines. This modified
duty cycle consists of two equally weighted points, 75 percent and 100
percent of full load, at rated speed. Since the transient cycle
described above involves extensive light-load operation, engines
qualifying for this high-load duty cycle would not need to measure
emissions over the transient cycle. Note that the field-testing
emission standards still apply to engines that don't certify to
transient duty-cycle standards.
Some diesel-derived engines operating on natural gas with power
ratings up to 1,500 or 2,000 kW may be covered by these emission
standards. Engine dynamometers with transient-control capabilities are
generally limited to testing engines up to 500 or 600 kW. At this time
emission standards and testing requirements related to transient duty
cycles will not apply for engines rated above 560 kW. We will likely
review this provision for Large SI engines once we have reached a
conclusion on the same issue for nonroad diesel engines. For example,
if we propose provisions for nonroad diesel engines that address
testing issues for these very large engines, we would likely propose
those same provisions for Large SI engines.
Test procedures related to evaporative emissions are described in
Section V.C.4 above. In general, this involves measuring evaporative
losses during a three-day period of cycling ambient temperatures
between 72[deg]
and 96[deg]
F.
2. What Fuels Are Used During Emission Testing?
For gasoline-fueled Large SI engines, we are adopting the same
specifications we have established for testing gasoline-fueled highway
vehicles and engines. This includes the revised specification to cap
sulfur levels at 80 ppm (65 FR 6698, February 10, 2000). These fuel
specifications apply for both exhaust and evaporative emissions.
For LPG, we are adopting the same specifications established by
California ARB. We understand that in-use fuel quality for LPG varies
significantly in different parts of the country and at different times
of the year. Not all in-use fuels outside California meet California
ARB specifications for certification fuel, but fuels meeting the
California specifications are nevertheless widely available. Test data
show that LPG fuels with a much lower propane content have only
slightly higher NOX and CO emissions (see Chapter 4 of the
Final Regulatory Support Document for additional information). These
data support our belief that engines certified using the specified fuel
will achieve the desired emission reduction for a wide range of in-use
fuels. At certification manufacturers provide deterioration factors
that take into account any effects related to the varying quality of
commercially available fuels.
For natural gas, we are adopting specifications similar to those
adopted by California ARB. As described in the Summary and Analysis of
Comments, we have adjusted some of the detailed specifications from the
proposal to reflect new data submitted after the proposal regarding
ranges of fuel properties reflecting current commercial fuels.
Unlike California ARB, we apply the fuel specifications to testing
only for emission measurements, not to service accumulation. Service
accumulation between emission tests may involve certification fuel or
any commercially available fuel of the appropriate type. We similarly
allow manufacturers to choose between certification fuel and any
commercial fuel for in-use measurements to show compliance with field-
testing emission standards.
Since publishing the proposal, we learned about issues related to
Large SI engines that operate around landfills or oil wells, where
engines may burn naturally occurring gases that are otherwise emitted
to the atmosphere. These gases generally consist of methane, but a wide
range of other constituents may also be mixed in. As a result, engines
may require adjustment over a wide range of settings for spark timing
and air-fuel ratio to maintain consistent combustion. We generally
believe that engine manufacturers should design their engines to
operate with automatic feedback controls as much as possible to avoid
the need for operators to manually adjust engines. However, in cases
involving these noncommercial fuels, there is no way to improve the
quality of the fuel to conform to any standardized specifications.
Also, it is clearly preferred to capture and burn these gases than to
emit them directly to the atmosphere, both to prevent greenhouse-gas
emissions and to avoid wasting this source of fuel. To address this
concern, we are adopting special provisions for engines burning
noncommercial fuels if they are unable to meet emission standards over
the full range of adjustability needed to accommodate the varying fuel
properties. Manufacturers would show that these engines can meet
emission standards using normal certification fuels, but the normal
provisions related to adjustable parameters would not apply. To
properly constrain this provision, we are including four requirements.
First, manufacturers would need to add information on an engine label
instructing operators how to make adjustments that would allow for
maintained emission control and overall engine performance. Second,
manufacturers would include additional label language to warn operators
that the engine may be used only in applications involving
noncommercial fuels. Third, manufacturers must separate these engines
into a distinct engine family. Fourth, manufacturers must keep a record
of individual sales of such engines.
3. Are There Production-Line Testing Provisions for Large SI Engines?
The provisions described in Section II.C.4 apply to Large SI
engines. These requirements are consistent with those adopted by
California ARB. One new issue specific to Large SI engines relates to
the duty cycles for measuring emissions from production-line engines.
For routine production-line testing, we require emission
measurements only with the steady-state duty cycles used for
certification. Due to the cost of sampling equipment for transient
engine operation, we do not require routine transient testing of
production-line engines. Transient testing of production-line engines
would add a substantial burden, since many manufacturers have limited
emission-sampling capability at production facilities; also, these
production facilities might be located at multiple sites. We believe
that steady-state emission measurements will give a good indication of
the manufacturers' ability to build engines consistent with the
prototypes on which their certification data are based. We reserve the
right, however, to direct a manufacturer to measure emissions with a
transient duty cycle if we believe it is appropriate. One indication of
the need for this transient testing would be if steady-state emission
levels from production-line engines are significantly higher than the
emission levels reported in the application for certification for that
engine family. For manufacturers with the capability of measuring
transient emission levels at the production line, we recommend doing
transient tests to better ensure that in-use tests will not reveal
problems in controlling emissions during transient
[[Page 68300]]
operation. Manufacturers need not make any measurements to show that
production-line engines meet field-testing emission standards.
We expect manufacturers generally to certify their engines to the
evaporative requirements using a design-based approach. Accordingly,
the technologies we expect manufacturers to use for controlling
evaporative emissions are not subject to variation as a result of
production procedures, so we are not requiring production-line testing
related to the evaporative requirements.
4. Are There In-Use Testing Provisions for Large SI Engines?
While the certification and production-line compliance requirements
are important to ensure that engines are designed and produced in
compliance with established emission limits, there is also a need to
confirm that manufacturers build engines with sufficient durability to
meet emission limits as they age in service. Consistent with the
California ARB program, we are requiring engine manufacturers to
conduct emission tests on a small number of field-aged engines to show
they meet emission standards.
We may generally select up to 25 percent of a manufacturer's engine
families in a given year to be subject to in-use testing. Most
companies will need to test at most one engine family per year.
Manufacturers may conduct in-use testing on any number of additional
engine families at their discretion.
Manufacturers in unusual circumstances may develop an alternate
plan to fulfill any in-use testing obligations, consistent with a
similar program we have adopted for outboard and personal watercraft
marine engines. These circumstances include total sales for an engine
family below 200 per year, installation only in applications where
testing is not possible without irreparable damage to the vehicle or
engine, or any other unique feature that prevents full emission
measurements.
While the regulations allow us to select an engine family every
year from an engine manufacturer, there are several reasons why small-
volume manufacturers may expect a less demanding approach. These
manufacturers may have only one or two engine families. If a
manufacturer shows that an engine family meets emission standards in an
in-use testing exercise, that may provide adequate data to show
compliance for that engine family for a number of years, provided that
the manufacturer continues to produce those engines without
significantly redesigning them in a way that might affect their in-use
emissions performance and that we do not have other reason to suspect
noncompliance. Also, where we have evidence that a manufacturer's
engines are likely in good in-use compliance, we generally take the
approach of selecting engine families based on some degree of
proportionality. To the extent that manufacturers produce a smaller
than average proportion of engines, they may expect us to select their
engine families less frequently, especially if other available data
pointed toward in-use compliance. In addition, our experience in
implementing a comparable testing program for recreational marine
engines provides a history of how we implement in-use testing
requirements.
Engines can be tested one of two ways. First, manufacturers can
remove engines from vehicles or equipment and test the engines on a
laboratory dynamometer using certification procedures. For 2004 through
2006 model year engines, this is the same steady-state duty cycle used
for certification; manufacturers may optionally test engines on the
dynamometer under transient operating conditions. For 2007 and later
model year engines, manufacturers must test engines using both steady-
state and transient duty cycles, as in certification.
As an alternative, manufacturers may use the specified equipment
and procedures for testing engines without removing them from the
equipment (referred to in this document as field testing). See Section
V.D.5 for a more detailed description of how to measure emissions from
engines during normal operation in the field. Since engines operating
in the field cannot be controlled to operate on a specific duty cycle,
compliance is demonstrated by comparing the measured emission levels to
the field-testing emission standards, which have higher numerical value
to account for the possible effects of different engine operation.
Because the engine operation can be so variable, however, engines
tested to show compliance only with the field-testing emission
standards are not eligible to participate in the in-use averaging,
banking, and trading program (described below).
Clean Air Act section 213 requires engines to comply with emission
standards throughout their regulatory useful lives, and section 207
requires a manufacturer to remedy in-use nonconformity when we
determine that a substantial number of properly maintained and used
engines fail to conform with the applicable emission standards (42
U.S.C. 7541). Along with the in-use testing program, we would allow
manufacturers to demonstrate that they have designed their engines to
control emissions substantially below the emission standards that
apply. If manufacturers are able to show that they have already been
reducing emissions more than required by the standards, including
appropriate consideration for deterioration and compliance margins,
this may allow us to conclude that these accumulated additional
emission reductions are sufficient to offset the high emissions from a
failing engine family. In concept, this approach serves much like a
banking program to recognize manufacturers' efforts to go beyond the
minimum required emission reductions.
This approach differs from the specific in-use emission-credit
program that we proposed. This more general approach is preferred for
two primary reasons. First, while we proposed to limit the in-use
emission-credit program to transient testing in the laboratory,
manufacturers will now be able to use emission data generated from
field testing to characterize an engine family's average emission
level. This becomes necessarily more subjective, but allows us to
consider a wider range of information in evaluating the degree to which
manufacturers are complying with emission standards across their
product line. Second, this approach makes clearer the role of the
emission credits in our consideration to recall failing engines. As we
described in the proposal, we plan to consider average emission levels
from multiple engine families in deciding whether to recall engines
from a failing engine family. We therefore believe it is not
appropriate to have a detailed emission-credit program defining
precisely how and when to calculate, generate, and use credits that do
not necessarily have value elsewhere.
The regulations do not specify how manufacturers would generate
emission credits to offset a nonconforming engine family. This gives us
the ability to consider any appropriate test data in deciding what
action to take. In generating this kind of information, some general
guidelines would apply. For example, we would expect manufacturers to
share test data from all engines and all engine families tested under
the in-use testing program, including nonstandard tests that might be
used to screen engines for later measurement. This allows us to
understand the manufacturers' overall level of performance in
controlling emissions to meet emission standards. Average emission
levels should be calculated over a running three-year period to include
a broad range of
[[Page 68301]]
testing without skewing the results based on old designs. Emission
values from engines certified to different tiers of emission standards
or tested using different measurement procedures should not be combined
to calculate a single average emission level. Average emission levels
should be calculated according to the following equation, rounding the
results to 0.1 g/kW-hr:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.000
Where:
Average EL=Average emission level in g/kW-hr.
Salesi=The number of eligible sales, tracked to the point of
first retail sale in the U.S., for the given engine family during the
model year.
i(STD-CL)=The difference between the emission standard and
the average emission level for an in-use testing family in g/kW-hr.
ULi=Useful life in hours.
Poweri=The sales-weighted average rated brake power for an
engine family in kW.
LFi=Load factor or fraction of rated engine power utilized
in use; use 0.50 for engine families used only in constant-speed
applications and 0.32 for all other engine families.
The anticipated crankcase and evaporative emission-control
technologies generally are best evaluated simply by checking whether or
not they continue to function as designed, rather than implementing a
program to measure these emissions from in-use engines. As a result, we
may inspect in-use engines to verify that these systems continue to
function properly throughout the useful life, but are not requiring
manufacturers to include crankcase or evaporative measurements as part
of the in-use testing program described in this section.
5. What Are the Field-Testing Emission Standards and Test Procedures?
To address concerns for controlling emissions outside of the
certification duty cycles and to enable field-testing of Large SI
engines, we are adopting procedures and standards that apply to a wider
range of normal engine operation.
a. What is the field-testing concept? Measuring emissions from
engines in the field as they undergo normal operation while installed
in nonroad equipment addresses two broad concerns. First, testing of
in-use engines has shown that emissions can vary dramatically under
certain modes of operation.
Second, this provides a low-cost method of testing in-use engines,
which facilitates in-use compliance programs.
Field-testing addresses this by including emission measurements
over the broad range of normal engine operation. This may include
varying engine speeds and loads according to real operation and may
include a reasonable range of ambient conditions, as described below.
No engine operating in the field can follow a prescribed duty cycle
for a consistent measure of emission levels. Similarly, no single test
procedure can cover all real-world applications, operations, or
conditions. Specifying parameters for testing engines in the field and
adopting an associated emission standard provides a framework for
requiring that engines control emissions under the whole range of
normal operation in the relevant nonroad equipment.
To ensure that emissions are controlled from Large SI engines over
the full range of speed and load combinations seen in the field, we are
adopting supplemental emission standards that apply more broadly than
the duty-cycle standard, as detailed below. These standards apply to
all regulated pollutants (NOX, HC, and CO) under all normal
operation (steady-state or transient). We exclude abnormal operation
(such as very low average power and extended idling time), but do not
restrict operation to any specific combination of speeds and loads. In
addition, the field-testing standards apply under a broad range of in-
use ambient conditions, both to ensure robust emission controls and to
avoid overly restricting the times available for testing. These
provisions are described in detail below.
b. How do the field-testing standards apply? Manufacturers have
expressed an interest in using field-testing procedures before the 2007
model year to show that they can meet emission standards as part of the
in-use testing program. While we are not adopting specific field-
testing standards for 2004 through 2006 model year engines, we will
allow this as an option. In this case, manufacturers would conduct the
field testing as described here to show that their engines meet the 5.4
g/kW-hr HC+NOX standard and the 50 g/kW-hr CO standard. This
may give manufacturers the opportunity to do testing at significantly
lower cost compared with laboratory testing. Preliminary certification
data from California ARB show that manufacturers are reaching steady-
state emission levels well below emission standards, so we expect any
additional variability in field-testing measurements not to affect
manufacturers' ability to meet the same emission standards.
The 2007 field-testing standards are based on emission data
measured on engines with the same emission-control technology used to
establish the duty-cycle standards. As described above for the duty-
cycle standards, we are adopting a flexible approach to address the
tradeoff between HC+NOX and CO emissions. Table V.D-1 shows
the range of values that define the standard for showing compliance for
field-testing measurements. The higher numerical values of the Tier 2
standards for field testing (compared with duty-cycle testing) reflect
the observed variation in emissions for varying engine operation, and
the projected effects of ambient conditions on the projected
technology. Conceptually, we believe that field-testing standards
should primarily require manufacturers to adjust engine calibrations to
effectively manage air-fuel ratios under varying conditions. The
estimated cost of complying with emission standards includes an
allowance for the time and resources needed for this recalibration
effort (see Section IX.B. for total estimated costs per engine).
Table V.D-1.--Samples of Possible Alternative Field-Testing Emission
Standards for Large SI Engines(g/kW-hr) *
------------------------------------------------------------------------
HC+NOX CO
------------------------------------------------------------------------
3.8......................................................... 6.5
3.1......................................................... 8.5
2.4......................................................... 11.7
1.8......................................................... 16.8
1.4......................................................... 23.1
[[Page 68302]]
1.1......................................................... 31
------------------------------------------------------------------------
* As described in the Final Regulatory Support Document and the
regulations, the values in the table are related by the following
formula: (HC+NOX) x CO0.791 = 16.78. These values follow directly from
the logarithmic relationship presented with the proposal in the Draft
Regulatory Impact Analysis.
We generally require manufacturers to show at certification that
they are capable of meeting all standards that apply for the useful
life. This adds a measure of assurance to both EPA and manufacturers
that the engine design is sufficient for any in-use engines to pass any
later testing. For Large SI engines, manufacturers must show in their
application for certification that they are able to meet the field-
testing standards. Manufacturers must submit a statement that their
engines will comply with field-testing emission standards under all
conditions that may reasonably be expected to occur in normal vehicle
operation and use. Manufacturer will provide a detailed description of
any testing, engineering analysis, and other information that forms the
basis for the statement. This will likely include a variety of steady-
state emission measurements not included in the prescribed duty cycle.
It may also include a continuous trace showing how emissions vary
during the transient test or it may include emission measurements
during other segments of operation manufacturers believe are
representative of the way their engines normally operate in the field.
Two additional provisions are necessary to allow emission testing
without removing engines from equipment in the field. Manufacturers
must design their engines to broadcast instantaneous speed and torque
values to the onboard computer and ensure that emission sampling is
possible after engine installation.
The test equipment and procedures for showing compliance with
field-testing standards also hold promise to reduce the cost of
production-line testing. Companies with production facilities that have
a dynamometer but no emission measurement capability may use the field-
testing equipment and procedures to get a low-cost, valid emission
measurement at the production line. Manufacturers may also choose to
use the cost advantage of the simpler measurement to sample a greater
number of production-line engines. This would provide greater assurance
of consistent emissions performance, but would also provide valuable
quality-control data for overall engine performance. See the discussion
of alternate approaches to production-line testing in Section II.C.4
for more information.
c. What limits are placed on field testing? The field-testing
standards apply to all normal operation. This may include steady-state
or transient engine operation. Given a set of field-testing standards,
the goal for the design engineer is to ensure that engines are properly
calibrated for controlling emissions under any reasonably expected mode
of engine operation. Engines may not be able to meet the emissions
limit under all conditions, however, so we are adopting several
parameters to narrow the range of engine operation that is subject to
the field-testing standards. For example, emission sampling for field
testing does not include engine starting.
Engines can often operate at extreme environmental and geographic
conditions (temperature, altitude, etc.). To narrow the range of
conditions for the design engineer, we are limiting emission
measurements during field testing to ambient temperatures from 13[deg]
to 35[deg]
C (55[deg]
to 95[deg] F), and to ambient pressures from 600
to 775 millimeters of mercury (which should cover almost all normal
pressures from sea level to 7,000 feet above sea level). This allows
testing under a wider range of conditions in addition to helping ensure
that engines are able to control emissions under the whole range of
conditions under which they operate.
Some additional limits to define ``normal'' operation apply to
field testing. These restrictions are intended to provide manufacturers
with some certainty about what their design targets are and to ensure
that compliance with the field-testing standards is feasible. These
restrictions apply to both variable-speed and constant-speed engine
applications.
First, measurements with more than 2 minutes of continuous idle are
excluded. This means that an emission measurement from a forklift while
it idled for 5 minutes will not be considered valid. On the other hand,
an emission measurement from a forklift that idled for multiple 1-
minute periods and otherwise operated at 40-percent power for several
minutes would be considered a valid measurement. Measurements with in-
use equipment in their normal service show that idle periods for Large
SI engines are short, but relatively frequent. We therefore do not
automatically exclude an emission sample if it includes an idling
portion. At the same time, controlling emissions during extended idling
poses a difficult design challenge, especially at low ambient
temperatures. Exhaust and catalyst temperatures under these conditions
can decrease enough that catalyst conversion is significantly less
effective. Since extended idling is not an appropriate focus of
extensive development efforts at this stage, we believe the 2-minute
threshold for continuous idle appropriately balances the need to
include measurement during short idling periods with the technical
challenges of controlling emissions under difficult conditions.
Second, measured power during the sampling period must be above 5
percent of maximum power for an emission measurement to be considered
valid. Brake-specific emissions (g/kW-hr) can be very high at low power
because they are calculated by dividing the g/hr emission rate by a
very small power level (kW). By ensuring that brake-specific emissions
are not calculated by dividing by power levels less than 5 percent of
the maximum, we can avoid this problem. The data presented in Chapter 4
of the Final Regulator Support Document show that engines can meet the
emission standards when operating above 5 percent of rated power.
Third, some engines need to run rich of stoichiometric combustion
during extended high-load operation to protect against engine failure.
This increases HC and CO emissions. We are adopting provisions allowing
manufacturers to meet separate standards for these engines for steady-
state operation. For engines qualifying for these different steady-
state standards, we specify that a valid sample for field testing must
include less than 10 percent of operation at 90 percent or more of
maximum power. We expect it to be uncommon for engine installations to
call for such high power demand due to the shortened engine lifetime at
very high-load operation. A larger engine can generally produce the
desired power at a lower relative load, without compromising engine
lifetime. Alternatively, applications that call for full-load operation
typically use diesel engines. Manufacturers may request a different
threshold to allow more open-loop operation. Before we approve such a
request, the engine manufacturer would need to have a plan for ensuring
that the engines in their final installation do not routinely operate
at loads above the specified threshold.
An additional parameter to consider is the minimum sampling time
for field testing. A longer period allows for
[[Page 68303]]
greater accuracy, due mainly to the smoothing effect of measuring over
several transient events. On the other hand, an overly long sampling
period can mask areas of engine operation with poor emission-control
characteristics. To balance these concerns, we are applying a minimum
sampling period of 2 minutes. In other rules for diesel engines, we
have allowed sampling periods as short as 30 seconds. Spark-ignition
engines generally don't have turbochargers and they control emissions
by maintaining air-fuel ratio with closed-loop controls through
changing engine operation. Spark-ignition engines are therefore much
less prone to consistent emission spikes from off-cycle or unusual
engine operation. We believe the 2-minute sampling time requirement
will ensure sufficient measurement accuracy and will allow for more
meaningful measurements from engines that may be operated with very
frequent but brief times at idle.
We do not specify a maximum sampling time. We expect manufacturers
testing in-use engines to select an approximate sampling time before
measuring emissions; however, the standards apply for any sampling time
that meets the minimum. When selecting an engine family for the in-use
testing program, we will develop a plan with direction related to the
way manufacturers conduct the emission-sampling effort, such as
sampling time or specific types of engine operation, to ensure that
testing provides relevant data.
d. How do I test engines in the field? To test engines without
removing them from equipment, analyzers are connected to the engine's
exhaust to detect emission concentrations during normal operation.
Exhaust volumetric flow rate and continuous power output are also
needed to convert the analyzer responses to units of g/kW-hr for
comparing to emission standards. These values can be calculated from
measurements of the engine intake flow rate, the exhaust air-fuel ratio
and the engine speed, and from torque information.
Available small analyzers and other equipment may be adapted for
measuring emissions from field equipment. A portable flame ionization
detector can measure total hydrocarbon concentrations. Methane
measurement currently requires more expensive laboratory equipment that
is impractical for field measurements. Field-testing standards are
therefore be based on total hydrocarbon emissions. A portable analyzer
based on zirconia technology measures NOX emissions. A
nondispersive infrared (NDIR) unit can measure CO. Emission samples can
best be drawn from the exhaust flow directly downstream of the catalyst
material to avoid diluting effects from the end of the tailpipe.
Installing a sufficiently long tailpipe extension is also an acceptable
way to avoid dilution. Mass flow rates also factor into the torque
calculation; this may either be measured in the intake manifold or
downstream of the catalyst.
Calculating brake-specific emissions depends on determining
instantaneous engine speed and torque levels. Manufacturers must
therefore design their engines to continuously monitor engine speed and
torque. The tolerance for speed measurements, which is relatively
straightforward, is +/-5 percent. For torque, the onboard computer
needs to convert measured engine parameters into useful units.
Manufacturers generally will need to monitor a surrogate value such as
intake manifold pressure or throttle position (or both), then rely on a
look-up table programmed into the onboard computer to convert these
torque indicators into newton-meters. Manufacturers may also want to
program the look-up tables for torque conversion into a remote scan
tool. Because of the greater uncertainty in these measurements and
calculations, manufacturers must produce their systems to report torque
values that are within 85 and 105 percent of the true value. This
broader range allows appropriately for the uncertainty in the
measurement, while providing an incentive for manufacturers to make the
torque reading as accurate as possible. Under-reporting torque values
would over-predict emissions. These tolerances are taken into account
in the selection of the field-testing standards, as described in
Chapter 4 of the Final Regulatory Support Document.
E. Special Compliance Provisions
We are adopting hardship provisions to address the particular
concerns of small-volume manufacturers, which generally have limited
capital and engineering resources. These hardship provisions are
generally described in Section VII.C. For Large SI engines, we are
adopting a longer available extension of the deadline, up to four
years, for meeting emission standards for companies that qualify for
special treatment under the hardship provisions. We will, however, not
extend the deadline for compliance beyond the four-year period. This
approach considers the fact that, unlike most other engine categories,
qualifying small businesses are more likely to be manufacturers
designing their own products. Other types of engines more often involve
importers, which are limited more by available engine suppliers than
design or development schedules.
We are not finalizing the proposed interim emission standards
proposed for small-volume manufacturers. We believe we can accomplish
the same objectives with more flexibility, and potentially with greater
net emission reductions, by relying on the hardship provisions.
In addition, we are waiving the requirement for small-volume
manufacturers to broadcast engine speed and torque values. These
companies may choose to do this to enable field-testing of their
products, but may be constrained in developing this capability to the
extent that they rely on component suppliers to provide systems that
meet EPA requirements.
F. Technological Feasibility of the Standards
We are adopting emission standards that depend on the industrial
versions of established automotive technologies. The most recent
advances in automotive technology have made possible even more dramatic
emission reductions. However, we believe that transferring some of
these most advanced technologies is not appropriate for nonroad engines
at this time, especially considering the much smaller sales volumes for
amortizing fixed costs and the additional costs associated with the
first-time regulation of these engines.
To comply with the 2004 model year standards, manufacturers should
not need to do any development, testing, or certification work that is
not already necessary to meet California ARB standards in 2004. As
shown in Chapter 4 of the Final Regulatory Support Document,
manufacturers can meet these standards with three-way catalysts and
closed-loop fuel systems. These technologies have been available for
industrial engine applications for several years. Moreover, several
manufacturers have already completed the testing effort to certify with
California ARB that their engines meet these standards. Complying with
emission standards nationwide in 2004 will therefore generally require
manufacturers only to produce greater numbers of the engines complying
with the California standards.
Chapter 4 of the Final Regulatory Support Document further
describes data and rationale showing why we believe that the 2007 model
year emission standards under the steady-state and transient duty-
cycles and field-testing procedures are feasible. In
[[Page 68304]]
summary, testing from Southwest Research Institute and other data show
that the same catalyst and fuel-system technologies needed to meet the
2004 standards can be optimized to meet more stringent emission
standards. Applying further development allows the design engineer to
fine-tune control of air-fuel ratios and address any high-emission
modes of operation to produce engines that consistently control
emissions to very low levels, even considering the wide range of
operation experienced by these engines. The numerical emission
standards are based on measured emission levels from engines that have
operated for at least 5,000 hours with a functioning emission-control
system. These engines demonstrate the achievable level of control from
catalyst-based systems and provide a significant degree of basic
development that should help manufacturers in optimizing their own
engines.
We believe it is appropriate to initiate the second stage of
standards in 2007, because we believe that applying these emission
standards earlier does not allow manufacturers enough stability between
introduction of different phases of emission standards to prepare for
complying with the full set of requirements in this final rule and to
amortize their fixed costs. Three years of stable emission standards,
plus the remaining lead time before 2004, allows manufacturers enough
time to go through the development and certification effort to comply
with the new standards including new test cycle requirements. The
provisions to allow ``family banking'' for early compliance provide an
additional tool for companies that choose to spread out their design
and certification efforts.
The new emission standards will either have no impact or a positive
impact with respect to noise, energy, and safety, as described in
Chapter 4 of the Final Regulatory Support Document. In particular, the
anticipated fuel savings associated with the expected emission-control
technologies will provide a very big energy benefit related to new
emission standards. The projected technologies are currently available
and are consistent with those anticipated for complying with the
emission standards adopted by California ARB. The lead time for the
near-term and long-term emission standards allows manufacturers enough
time to optimize these designs to most effectively reduce emissions
from the wide range of Large SI equipment applications.
VI. Recreational Marine Diesel Engines
This section describes the new provisions for 40 CFR part 94, which
apply to engine manufacturers and importers. We are applying the same
general compliance provisions from 40 CFR part 94 for engine
manufacturers, equipment manufacturers, operators, rebuilders, and
others. See Section II for a description of our general approach to
regulating nonroad engines and how manufacturers show that they meet
emission standards.
A. Overview
We are adopting exhaust and crankcase emission standards for
recreational marine diesel engines with power ratings greater than or
equal to 37 kW. We are adopting emission standards for HC,
NOX, CO, and PM beginning in 2006. We believe manufacturers
will be able to use technology developed for land-based nonroad and
commercial marine diesel engines. To encourage the introduction of low-
emission technology, we are also adopting voluntary ``Blue Sky''
standards which are 40 percent lower than the mandatory standards. We
also recognize that there are many small businesses that manufacture
recreational marine diesel engines. We are therefore including several
regulatory options for small businesses that will help minimize any
unique burdens caused by emission regulations.
Diesel engines are primarily available in inboard marine
configurations, but may also be available in sterndrive and outboard
marine configurations. Inboard diesel engines are the primary choice
for many larger recreational boats.
B. Engines Covered by This Rule
The standards in this section apply to recreational marine diesel
engines. We excluded these engines from the requirements applying to
commercial marine diesel engines because at the time we thought their
operation in planing mode might impose design requirements on
recreational boat builders and to allow us more time for further
evaluation prior to setting standards (64 FR 73300, December 29, 1999).
Commercial marine vessels tend to be displacement-hull vessels,
designed and built for a unique commercial application (such as towing,
fishing, or general cargo). Power ratings for engines used on these
vessels are analogous to land-based applications, and these engines
generally have warranties for 2,000 to 5,000 hours of use. Recreational
vessels, on the other hand, tend to be planing vessels. Engines used on
these vessels are designed to achieve higher power output with less
engine weight. This increase in power reduces the lifetime of the
engine, so recreational marine engines have shorter warranties than
their commercial counterparts. In our previous rulemaking, recreational
engine industry representatives raised concerns about the ability of
these engines to meet the commercial standards without substantial
changes in the size and weight of the engine. Such changes may have an
impact on vessel builders, who might have to redesign vessel hulls to
accommodate the new engines. Because most recreational vessel hulls are
made with fiberglass molds, this may be a significant burden for
recreational vessel builders.
Our further evaluation of these issues leads us to conclude that
recreational marine diesel engines can achieve those same emission
standards without significant impacts on engine size and weight, and
therefore without significant impacts on vessel design. Section VI.G of
this document, Chapters 3 and 4 of the Final Regulatory Support
Document, and Section II.A of the Summary and Analysis of Comments
describe the several technological changes we anticipate manufacturers
will use to comply with the new emission standards. None of these
technologies has an inherent negative effect on the performance or
power density of an engine. As with engines in land-based applications,
we expect that manufacturers will be able to use the range of
technologies available to maintain or even improve the performance
capabilities of their engines. We are establishing a separate
regulatory program for recreational marine diesel engines in this rule,
with most aspects the same as for commercial marine diesel engines but
with certain aspects of the program tailored to these applications,
notably the not-to-exceed emissions requirements.
To distinguish between commercial and recreational marine diesel
engines for the purpose of emission controls, it is necessary to define
``recreational marine diesel engine.'' The commercial marine diesel
engine rule defined recreational marine engine as a propulsion marine
engine that is intended by the manufacturer to be installed on a
recreational vessel. The engine must be labeled to distinguish it from
a commercial marine diesel engine. The label must read: ``THIS ENGINE
IS CATEGORIZED AS A RECREATIONAL ENGINE UNDER 40 CFR PART 94.
INSTALLATION OF THIS ENGINE IN ANY NONRECREATIONAL VESSEL IS A
[[Page 68305]]
VIOLATION OF FEDERAL LAW SUBJECT TO PENALTY.''
We are revising this definition to include a requirement that a
recreational marine engine must be a Category 1 marine engine (have a
displacement of less than 5 liters per cylinder). Category 2 marine
engines are generally designed with characteristics similar to
commercial marine engines. Vessels using engines of this size generally
require engines that can operate longer at higher power than typical
recreational boats; therefore, these engines generally have a lower
power density and are not offered in a ``recreational'' rating.
For the purpose of the recreational marine diesel engine definition
included in the proposal, recreational vessel was defined as ``a vessel
that is intended by the vessel manufacturer to be operated primarily
for pleasure or leased, rented, or chartered to another for the
latter's pleasure.'' Because certain vessels that are used for pleasure
may have operating characteristics that are more similar to commercial
marine vessels (such as excursion vessels and charter craft), we drew
on the Coast Guard's definition of a ``small passenger vessel'' (46
U.S.C. 2101 (35)) to further delineate what would be considered to be a
recreational vessel. Specifically, the term ``operated primarily for
pleasure or leased, rented or chartered to another for the latter's
pleasure'' does not include the following vessels: (1) Vessels of less
than 100 gross tons that carry more than 6 passengers; (2) vessels of
100 gross tons or more that carry one or more passengers; or (3)
vessels used solely for competition. For the purposes of this
definition, a passenger is defined by 46 U.S.C 2101 (21, 21a) which
generally means an individual who pays to be on the vessel.
We received several comments in this rulemaking on these
definitions. Engine manufacturers were concerned that the definitions
may be unworkable for engine manufacturers, because they cannot know
whether a particular recreational vessel might carry more than six
passengers at a time. All they can know is whether the engine they
manufacture is intended by them for installation on a vessel designed
for pleasure and having the corresponding characteristics for planing,
power density, and performance requirements.
We are not revising our existing definition of recreational marine
vessel. As discussed in the Summary and Analysis of Comments, a vessel
will be considered recreational if the boat builder intends that the
customer will operate it consistent with the recreational-vessel
definition. Relying on the boat builder's intent is necessary because
manufacturers need to establish a vessel's classification before it is
sold, whereas the Coast Guard definitions apply at the time of use. The
definition therefore relies on the intent of the boat builder to
establish that the vessel will be used consistent with the above
criteria. If a boat builder manufactures a vessel for a customer who
intends to use the vessel for recreational purposes, we would always
consider that a recreational vessel, regardless of how the owner (or a
subsequent owner) actually uses it. The engine manufacturer will not be
expected to ensure that their engines are used only in recreational
craft; however, they would be required to label their recreational
engines as described above. The vessel builders will then be required
to install properly certified recreational (or commercial) marine
engines in recreational vessels and certified commercial marine engines
in commercial vessels.
C. Emission Standards for Recreational Marine Diesel Engines
This section describes the new emission standards and
implementation dates, with an outline of the technology that can be
used to achieve these levels. The technological feasibility discussion
below (Section VI.G) describes our technical rationale in more detail.
1. What Are the Emission Standards and Compliance Dates?
The emission standards for recreational marine diesel engines are
the same as the Tier 2 standards for commercial marine diesel engines
with two years additional lead time. We are setting the standards at
the same level because recreational marine diesel engines can use all
the technologies projected for Tier 2 and these technologies are
expected to lead to compliance. As with commercial marine engines this
technology will be available in the lead time provided to allow
compliance with the emission standards. Many of these engines already
use this technology. This includes electronic fuel management,
turbocharging, and separate-circuit aftercooling. In fact, because
recreational engines have much shorter design lives than commercial
engines, it is easier to apply raw-water aftercooling to these engines,
which allows manufacturers to enhance performance while reducing
NOX emissions.
Engine manufacturers will generally increase the fueling rate in
recreational engines, compared to commercial engines, to gain power
from a given engine size. This helps bring a planing vessel onto the
water surface and increases the maximum vessel speed without increasing
the weight of the vessel. This difference in how recreational engines
are designed and used affects emissions. However, the technology listed
above can be used to meet the emission standards while still meeting
the performance requirements of a recreational engine.
We are adopting the commercial marine engine standards for
recreational marine diesel engines, allowing two years beyond the dates
that standards apply for the commercial engines. This gives engine
manufacturers additional lead time in adapting technology to their
recreational marine diesel engines. For manufacturers producing only
recreational marine engines the implementation dates provide three to
six years of lead time beyond this notice. Based on our evaluation of
the industry, we believe that manufacturers who produce only
recreational marine engines would likely be small businesses and would
have the option of additional lead time, and other flexibility, as
discussed in Section VI.E. The emission standards and implementation
dates for recreational marine diesel engines are presented in Table
VI.C-1. The subcategories refer to engine displacement in liters per
cylinder.
Table VI.C-1.--Recreational Marine Diesel Emission Standards and Implementation Dates
----------------------------------------------------------------------------------------------------------------
HC+NOX g/kW- Implementation
Subcategory hr PM g/kW-hr CO g/kW-hr date
----------------------------------------------------------------------------------------------------------------
power £= 37 kW disp < 0.9............. 7.5 0.40 5.0 2007
0.9 <= disp < 1.2............................... 7.2 0.30 5.0 2006
1.2 <= disp < 2.5............................... 7.2 0.20 5.0 2006
disp £= 2.5........................... 7.2 0.20 5.0 2009
----------------------------------------------------------------------------------------------------------------
[[Page 68306]]
Manufacturers commented that engines with less than 2.5 liters per
cylinder, but more than 560 kW would have no lead time beyond the land-
based nonroad diesel engine standards and that some commercial marine
engines in this category would actually have to certify two years
before nonroad engines. In this case this is caused by the way we
define subclasses, but has technology and cost implications for the
engines involved. To address this, we are providing an optional
implementation date of 2008 for certain commercial and recreational
marine engines (see the Summary and Analysis of Comments for more
detail). To be eligible for this option, the engine must be derived
from a land-based nonroad engine with a rated power greater than 560 kW
and have a displacement of 2.0 to 2.5 liters per cylinder. To use this
option, we are requiring that engines certified under this option meet
an HC+NOX standard of 6.4 g/kW-hr through model year 2012.
We believe this emission level, which matches the Tier 2 level for
land-based nonroad engines, should be achievable given the extra lead
time for development. Testing would still be performed on the
appropriate marine duty cycles. Based on our analysis in the Final
Regulatory Impact Analysis for commercial marine engines,
HC+NOX emissions measured over the marine duty cycles should
be similar to those measured over the land-based nonroad duty cycle.
We are also adopting not-to-exceed emission standards and related
requirements similar to those finalized for commercial marine diesel
engines. This is discussed below in Section VI.C.8.
2. Will I Be Able To Average, Bank, or Trade Emissions Credits?
Manufacturers may use emission credits from recreational marine
diesel engines to show that they meet emission standards. Section
II.C.3 gives an overview of the emission-credit program, which is
consistent with what we have adopted for Category 1 commercial marine
diesel engines. The emission-credit program covers HC+NOX
and PM emissions, but not CO emissions.
Consistent with our land-based nonroad and commercial marine diesel
engine regulations, manufacturers may not simultaneously generate
HC+NOX credits while using PM credits on the same engine
family, and vice versa. This is necessary because of the inherent
trade-off between NOX and PM emissions in diesel engines.
We are adopting the same maximum value of the Family Emission Limit
(FEL) as for commercial marine diesel engines. For engines with a
displacement of less than 1.2 liters/cylinder, the maximum values are
11.5 g/kW-hr HC+NOX and 1.2 g/kW-hr PM; for larger engines,
the maximum values are 10.5 g/kW-hr HC+NOX and 0.54 g/kW-hr
PM. These maximum FEL values were based on the comparable land-based
emission-credit program and will ensure that the emissions from any
given family certified under this program not be significantly higher
than the applicable emission standards. We believe these maximum values
will prevent backsliding of emissions above the baseline levels for any
given engine model. Also, we are concerned that the higher emitting
engines may cause increased emissions in areas such as ports that may
have a need for PM or NOX emission reductions. Nonetheless,
it is acknowledged that recreational marine diesel engines constitute a
small fraction of PM and HC + NOX emissions in nonattainment
areas.
Emission credits generated under this program have no expiration,
with no discounting applied. This is consistent with the commercial
marine credit program and gives manufacturers more options in
implementing their engine designs. However, if we revisit these
standards later, we will have to reevaluate this issue in the context
of whether future advances in technology would result in a large amount
of accumulated credits that would adversely impact the timely
implementation of any new requirements.
Consistent with the land-based nonroad diesel rule, we will also
not allow manufacturers to use credits generated on land-based engines
for demonstrating compliance with marine diesel engines. In addition,
credits may not be exchanged between recreational and commercial marine
engines. The emission standards for recreational engines are based on
the baseline levels of current recreational marine engines and the
capability of technology to reduce emissions from recreational marine
engines. The standard is, therefore, premised on the capability and use
of recreational marine technology and not on the capability and use of
technology on other engines. Emissions from land-based, commercial, and
recreational marine engines are measured over different duty cycles and
have different useful lives. Correction factors would be difficult to
generate and they would add complexity and uncertainty to the value of
the credits. Furthermore, we are concerned that allowing cross program
trading could create an inequity between manufacturers with diverse
product lines and those with more limited offerings, thereby
potentially creating a competitive advantage for diverse companies over
small companies selling only recreational marine engines. If a
manufacturer were to do this, we do not believe it is likely that they
would sell emission credits at a price that would be economical for
small manufacturers.
We will allow early banking of emission credits relative to the
standard. Early banking of emission credits may allow for a smoother
implementation of the recreational marine standards. These credits are
generated relative to the new emission standards and are undiscounted.
We will also allow manufacturers to generate early credits relative
to their pre-control emission levels. If manufacturers choose this
option they will have to develop baseline emission levels specific to
each participating engine family. Credits will then be calculated
relative to the manufacturer-generated baseline emission rates, rather
than the standards. To generate the baseline emission rates, a
manufacturer must test three engines from the family for which the
baseline is being generated. The baseline will be the average emissions
of the three engines. Under this option, engines must still certify to
the standards to generate credits, but the credits will be calculated
relative to the generated baseline rather than the standards. Any
credits generated between the level of the standards and the generated
baseline will be discounted 10 percent. This is to account for the
variability of testing in-use engines to establish the family-specific
baseline levels, which may result from differences in hours of use and
maintenance practices as well as other sources of potential uncertainty
about the representativeness if the baseline. Manufacturers commented
that credits should not be generated under the early banking program
for the portion of NOX reductions above the MARPOL Annex VI
standard. We believe this approach is reasonable since this should be a
common upper limit for all engines. Therefore, if manufacturers use
this option, any baseline NOX levels determined to be above
the MARPOL Annex VI standard must be adjusted to that level for
determining early credits.
3. Is EPA Proposing Voluntary Standards for These Engines?
a. Blue Sky. We are adopting voluntary emission standards based on
a 45-percent reduction beyond the mandatory standards. An engine family
meeting the voluntary standards
[[Page 68307]]
qualifies for designation as Blue Sky Series engines. These voluntary
standards are the same as those adopted for commercial marine diesel
engines (see Table VI.C-2). While the Blue Sky Series emission
standards are voluntary, a manufacturer choosing to certify an engine
under this program must comply with all the requirements that apply to
this category of engines, including allowable maintenance, warranty,
useful life, rebuild, and deterioration factor provisions. This program
is effective immediately when we publish this rule. To maximize the
potential for other groups to create incentive programs, without
double-counting, we do not allow manufacturers to earn marketable
credits for their Blue Sky Engines.
Table VI.C-2.--Blue Sky Voluntary Emission Standards for Recreational
Marine Diesel Engines
[g/kW-hr]
------------------------------------------------------------------------
Rated brake power (kW) HC+NOX PM
------------------------------------------------------------------------
power £= 37 kW displ.<0.9............... 4.0 0.24
0.9<=displ.<1.2................................... 4.0 0.18
1.2<=displ.<2.5................................... 4.0 0.12
2.5<=displ........................................ 5.0 0.12
------------------------------------------------------------------------
b. MARPOL Annex VI. The MARPOL Annex VI standards are for
NOX emissions from marine diesel engines rated above 130 kW.
We encourage engine manufacturers to make Annex VI-compliant engines
available and boat builders to purchase and install them before we
apply the EPA Tier 2 standards. If the treaty enters into force, the
standards would go into effect retroactively to all boats built January
1, 2000 or later. One advantage of using MARPOL-compliant engines is
that if this happens, users will be in compliance with the standard
without having to make any changes to their engines.
4. What Durability Provisions Apply?
Several provisions help ensure that engines control emissions
throughout a lifetime of operation. Section II.C gives a general
overview of durability provisions associated with emissions
certification. This section discusses these provisions specifically for
recreational marine diesel engines.
a. How long do my engines have to comply? Manufacturers must
produce engines that comply over a useful life of ten years or until
the engine accumulates 1,000 operating hours, whichever occurs first.
The hours requirement is a minimum value for useful life, and
manufacturers must comply for a longer period in those cases where they
design their engines to be operated longer than 1,000 hours. In making
the determination that engines are designed to last longer than the
1,000 hour value, we will consider evidence such as whether the engines
continue to reliably deliver the necessary power output without an
increase in fuel consumption that the user would find unacceptable and
thus might trigger a maintenance or rebuild action by the user.
b. How do I demonstrate emission durability? We are extending the
durability demonstration requirements for commercial marine diesel
engines to also cover recreational marine diesel engines. This means
that recreational marine engine manufacturers, using good engineering
judgment, will generally need to test one or more engines for emissions
before and after accumulating the number of hours consistent with the
engine useful life (usually performed by continuous engine operation in
a laboratory). The results of these tests are referred to as
``durability data,'' and are used to determine the rates at which
emissions are expected to increase over the useful life of the engine
for each engine family The rates are known as deterioration factors.
However, in many cases, manufacturers may use durability data from a
different engine family, or for the same engine family in a different
model year. Because of this allowance to use the same data for multiple
engine families, we expect durability testing to be very limited.
We also specify that manufacturers must collect durability data and
generate deterioration factors using the same methods established for
commercial marine diesel engines. These requirements are in 40 CFR
94.211, 94.218, 94.219, and 94.220. These sections describe when
durability data from one engine family can be used for another family,
how to select to the engine configuration that is to be tested, how to
conduct the service accumulation, and what maintenance can be performed
on the engine during this service accumulation. Under 40 CFR 94.220,
manufacturers may project deterioration rates from engines with an
accumulation of less than 1,000 hours, as long as the amount of service
accumulation completed and projection procedures are determined using
good engineering judgment.
c. What maintenance may be done during service accumulation? For
engines certified to a 1,000-hour useful life, the only maintenance
that may be done must be: (1) Regularly scheduled, (2) unrelated to
emissions, and (3) technologically necessary. This typically includes
changing engine oil, oil filter, fuel filter, and air filter. For
recreational marine diesel engines certified to longer lives, these
engines will be subject to the same minimum allowable maintenance
intervals as commercial marine engines. These intervals and the
allowable maintenance are specified in 40 CFR 94.211.
d. Are there production-line testing provisions? We are adopting
the production-line testing requirements from commercial marine engines
for recreational marine diesel engines, with the additional provisions
described in II.C.4. A manufacturer must test one percent of its total
projected annual sales of Category 1 engines each year to meet
production-line testing requirements. We are not adopting a minimum
number of tests, so a manufacturer who produces no more than 100 marine
diesel engines is not required to do any production-line testing.
Similar to the commercial marine requirements, manufacturers have the
option of using alternative production-line testing programs with EPA
approval.
Manufacturers commented that we should limit the number of engines
tested for a given engine family to five, arguing that five engines
would be sufficient to demonstrate compliance with the standards.
Although there isn't necessarily an engineering rationale for capping
the number of tests for each engine family to five, we believe that
statistical certainty can be determined using the Cumulative Sum method
described for recreational vehicles in 40 CFR part 1051, subpart D.
Therefore, we are providing the option of using the Cumulative Sum
method for determining sample sizes under the production-line testing
program. For marine engines, PM would need to be included in this
methodology. Under the Cumulative Sum method, a statistical analysis is
applied to test results to establish the number of tests needed. This
may limit the number of engines tested to less than 1 percent of the
production volume in cases where there is low variability in the test
data.
5. Do These Standards Apply to Alternative-Fueled Engines?
These new standards apply to all recreational marine diesel
engines, without regard to the type of fuel used. While we are not
aware of any alternative-fueled recreational marine diesel engines
currently being sold into the U.S. market, alternate forms of the
hydrocarbon standards address the potential for natural gas-fueled and
[[Page 68308]]
alcohol-fueled engines. In our regulation of highway vehicles and
engines, we determined that nonmethane standards should be used in
place of total hydrocarbon standards for engines fueled with natural
gas (which is comprised primarily of methane) (59 FR 48472, September
21, 1994). These alternate forms follow the precedent set in previous
rulemakings to make the standards similar in stringency and
environmental impact.
Similarly, we are applying HC-equivalent (HCE) standards instead of
total hydrocarbon standards to alcohol-fueled highway engines and
vehicles (54 FR 14426, April 11, 1989). HC-equivalent emissions are
calculated from the oxygenated organic components and non-oxygenated
organic components of the exhaust, summed together based on the amount
of organic carbon present in the exhaust. Alcohol-fueled recreational
marine engines must therefore comply with total hydrocarbon equivalent
(THCE) plus NOX standards instead of THC plus NOX
standards.
6. Is EPA Controlling Crankcase Emissions?
Manufacturers must prevent crankcase emissions from recreational
marine diesel engines, with one exception. Turbocharged recreational
marine diesel engines may be built with open crankcases, as long as the
crankcase ventilation system allows for measurement of crankcase
emissions. For these engines with open crankcases, we will require
crankcase emissions to be either routed into the exhaust stream to be
included in the exhaust measurement, or to be measured separately and
added to the measured exhaust mass. These measurement requirements do
not add significantly to the cost of testing, especially where the
crankcase vent is simply routed into the exhaust stream prior to the
point of exhaust sampling. These provisions are consistent with our
previous regulation of crankcase emissions from such diverse sources as
commercial marine engines, locomotives, and passenger cars.
7. What Are the Smoke Requirements?
We are not adopting smoke requirements for recreational marine
diesel engines. Marine diesel engine manufacturers have stated that
many of their engines, though currently unregulated, are manufactured
with smoke limiting controls at the request of customers. Users seek
low smoke emissions both because they dislike the exhaust residue on
decks and because they can be subject to penalties in ports with smoke
emission requirements. In many cases, marine engine exhaust gases are
mixed with water prior to being released. This practice reduces smoke
visibility. Moreover, we believe that applying PM standards will have
the effect of limiting smoke emissions as well.
8. What Are the Not-To-Exceed Standards and Related Requirements?
a. Concept. Our goal is to achieve control of emissions over the
broad range of in-use speed and load combinations that can occur on a
recreational marine diesel engine so that real-world emission control
is achieved, rather than just controlling emissions under certain
laboratory conditions. An important tool for achieving this goal is an
in-use program with an objective emission standard and an easily
implemented test procedure. Prior to this concept, our approach has
been to set a numerical standard on a specified test procedure and rely
on the additional prohibition of defeat devices to ensure in-use
control over a broad range of operation not included in the test
procedure.
We are applying the defeat device provisions established for
commercial marine engines to recreational marine diesel engines in
addition to the NTE requirements (see 40 CFR 94.2). A design in which
an engine met the standard at the steady-state test points but was
intentionally designed to approach the NTE limit everywhere else would
be considered to be defeating the standard. Electronic controls that
recognize and modulate the emission-control system when the engine is
not being tested for emissions and increases the emissions from the
engine would be an example of a defeat device, regardless of the
emissions performance of the engine with regard to the standards.
No single test procedure can cover all real-world applications,
operations, or conditions. Yet to ensure that emission standards are
providing the intended benefits in use, we must have a reasonable
expectation that emissions under real-world conditions reflect those
measured on the test procedure. The defeat-device prohibition is
designed to ensure that emission controls are employed during real-
world operation, not just under laboratory or test-procedure
conditions. However, the defeat-device prohibition is not a quantified
standard and does not have an associated test rocedure, so it does not
have the clear objectivity and ready enforceability of a numerical
standard and test procedure. As a result, relying on just a using a
standardized test procedure and the defeat device prohibition makes it
harder to ensure that engines will operate with the same level of
control in the real world as in the test cell.
Because the ISO E5 duty cycle uses only five modes on an average
propeller curve intended to characterize typical marine engine
operation for this industry, we are concerned that an engine designed
to the duty cycle may not necessarily perform the same way over the
range of speed and load combinations normally seen on a boat nor will
it always follow the average curve. These duty cycles are based on an
average propeller curve, but a propulsion marine engine may never be
fitted with an ``average propeller.'' In addition, even if fitted with
an ``average propeller,'' an engine fit to a specific boat may operate
differently based on how heavily the boat is loaded.
To ensure that emissions are controlled from recreational marine
engines over the full range of speed and load combinations normally
seen on boats, we are establishing a zone under the engine's power
curve where the engine may not exceed a specified emission limit. This
limit applies to all of the regulated pollutants under steady-state
operation. Testing in this ``not-to-exceed'' (NTE) zone may include the
whole range of real ambient conditions. The NTE zone, limit, and
ambient conditions are described below.
We believe there are significant advantages to taking this
approach. The test procedure is flexible enough to represent the
majority of in-use engine operation and ambient conditions. Therefore,
the NTE approach takes all of the benefits of a numerical standard and
test procedure and expands it to cover a broad range of conditions.
Also, a standard that requires laboratory testing makes it harder to
perform in-use testing because either the engines must be removed from
the vessel or laboratory-type conditions must be achieved on the
vessel. With the NTE approach, in-use testing becomes much easier to
implement since emissions may be sampled during normal vessel use.
Because this approach is objective, it makes enforcement easier and
provides more certainty to the industry in terms of what control is
expected in-use versus over a fixed laboratory test procedure.
Even with the NTE requirements, we believe it is important to
retain standards based on the steady-state duty cycles. This is the
standard that we expect the certified marine engines to meet on average
in use. The NTE testing is more focused on maximum emissions for
segments of operation. We believe
[[Page 68309]]
basing the emission standards on a distinct cycle and using the NTE
zone to better ensure in-use control creates a comprehensive program.
In addition, the steady-state duty cycles give a basis for calculating
credits for averaging, banking, and trading.
As described in the Summary and Analysis of Comments, the same
technology that can be used to meet the standards over the E5 duty
cycle can be used to meet the NTE caps in the NTE zone. We therefore do
not expect these standards to cause recreational marine diesel engines
to need more advanced technology that is used by the nonroad and
commercial marine engines from which they are derived. We do not
believe the NTE concept results in a large amount of additional
testing, because these engines should be designed to perform as well in
use as they do over the steady-state five-mode certification test.
However, our cost analysis in Chapter 5 of the Final Regulatory Support
Document accounts for some additional testing, especially in the early
years, to provide manufacturers with assurance that their engines will
meet the NTE requirements.
b. Shape of the NTE zone. Figure VI.C-1 illustrates the NTE zone
for recreational marine diesel engines. We based this zone on the range
of conditions that these engines might typically see in use. Also, we
divide the zone into subzones of operation which have different limits
as described below. Chapter 4 of the Final Regulatory Support Document
describes the development of the boundaries and conditions associated
with the NTE zone. The NTE zone for recreational marine diesel engines
is the same for commercial marine diesel engines operating on a
propeller curve, except that an additional subzone is added at speeds
over 95 percent of rated to address the typical recreational design for
higher rated power.
BILLING CODE 6560-50-P
[[Page 68310]]
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.002
BILLING CODE 6560-50-C
EPA may approve adjustments to the size and shape of the NTE zone
for certain engines if the manufacturer demonstrates that the engine
will not see operation outside of the revised NTE zone in use. This
way, manufacturers can avoid having to test their engines under
operation that they will not see in use. However, manufacturers are
responsible for ensuring that their specified operation represents
real-world operation. In addition, if a manufacturer designs an engine
for operation at speeds and loads outside of the NTE zone (i.e.,
variable-speed engines used with variable-pitch propellers), the
manufacturer is responsible for notifying us, so the NTE zone for that
engine family can be modified to include this operation.
c. Transient operation. NTE testing includes only steady-state
operation with a minimum sampling time of 30 seconds. We specify the
ISO E5 steady-state duty cycle for showing compliance with average
emission standards. The goal of adopting NTE standards and
[[Page 68311]]
procedures is to cover the operation away from the five modes that are
on the assumed propeller curve. Our understanding is that the majority
of marine engine operation is steady-state; however, we recognize that
recreational marine use is likely more transient than commercial marine
use. At this time we do not have enough data on marine engine operation
to accurately determine the amount of transient operation that occurs
or to set an NTE standard for transient operation. We are aware that
the high-load transient operation seen when a boat comes to plane is
not included in the NTE zone as defined, even if we were to require
compliance with NTE standards during transient operation. We are also
aware that these speed and load points cannot be achieved under steady-
state operation for a properly loaded boat in use. If we find that
excluding transient operation from the compliance requirements results
in a significant increase in emissions, we will revisit this provision
in the future. Also, an engine designed, with multiple injection timing
maps based on operation, to operate at higher emissions during
transient operation than during steady-state testing would be in
noncompliance with our defeat device prohibition.
d. Emission standards. We are requiring emissions caps for the NTE
zones that represent a multiplier times the weighted test result used
for certification for all of the regulated pollutants
(HC+NOX, CO, and PM). This is consistent with the concept of
a weighted modal emission test such as the steady-state tests included
in this rule. The standard itself is intended to represent the average
emissions under steady-state conditions. Because it is an average, some
points can be higher, some lower, and the manufacturer will design to
maximize performance and still meet the engine standard. The NTE limit
is on top of this. It is designed to make sure that no part of the
engine operation and that no application goes too far from the average
level of control.
Consistent with the requirements for commercial marine engines,
recreational marine diesel engines must meet a cap of 1.50 times the
certified level for HC+NOX, PM, and CO for the speed and
power subzone below 45 percent of rated power and a cap of 1.20 times
the certified levels at or above 45 percent of rated power. However, we
are applying an additional subzone at speeds greater than 95 percent of
rated, with a corresponding standard of 1.50 times the certified levels
for this subzone. This additional subzone addresses the typical
recreational design for higher rated power. We understand that this
power is needed to ensure that the engine can bring the boat to plane.
Chapter 4 of the Final Regulatory Support Document provides more detail
on how we determined the standards.
We are aware that marine diesel engines may not be able to meet the
emissions limit under all conditions. Specifically, there are times
when emission control must be compromised for startability or safety.
Engine starting is not included in NTE testing. In addition,
manufacturers have the option of petitioning the Administrator to allow
emissions to increase under engine protection strategies, such as when
an engine overheats. This is also consistent with the requirements for
commercial marine engines.
e. Ambient conditions. Variations in ambient conditions can affect
emissions. Such conditions include air temperature, humidity, and
(especially for aftercooled engines) water temperature. We are applying
the commercial marine engine ranges for these variables. Chapter 4 of
the Final Regulatory Support Document provides more detail on how we
determined these ranges. Within the ranges, there is no calculation to
correct measured emissions to standard conditions. Outside of the
ranges, emissions can be corrected back to the nearest end of the
range. The ambient variable ranges are 13 to 35[deg]C (55 to 95[deg]F)
for intake air temperature, 7.1 to 10.7 g water/kg dry air (50 to 75
grains/pound dry air) for intake air humidity, and 5 to 27[deg]C (41 to
80[deg]F) for ambient water temperature.\84\
---------------------------------------------------------------------------
\84\ The range of intake air temperature is 13 to 30[deg]C for
engines that draw air from outside the engine room.
---------------------------------------------------------------------------
f. Certification. At the time of certification, manufacturers must
submit a statement that its engines will comply with these requirements
under all conditions that may reasonably be expected to occur in normal
vessel operation and use. The manufacturer also provides a detailed
description of all testing, engineering analysis, and other information
that forms the basis for the statement. This statement may be based on
testing other research that validly supports such a statement,
consistent with good engineering judgment. EPA may review the basis of
this statement during the certification process.
D. Testing Equipment and Procedures
The regulations detail specifications for test equipment and
procedures that apply generally to commercial marine engines (including
NTE testing) in 40 CFR part 94. We have based the recreational marine
diesel engine test procedures on this part. Section VIII gives a
general discussion of testing requirements; this section describes
procedures that are specific to recreational marine such as the duty
cycle for operating engines for emission measurements. Chapter 4 of the
Draft Regulatory Support Document describes these duty cycles in
greater detail. In addition to the information provided above, the
following section discusses issues concerning test equipment and
procedures.
1. Which Duty Cycles Are Used To Measure Emissions?
For recreational marine diesel engines, we specify the ISO E5 duty
cycle. This is a 5-mode steady state cycle, including an idle mode and
four modes lying on a cubic propeller curve. ISO intends for this cycle
to be used for all engines in boats less than 24 meters in length. We
apply it to all recreational marine diesel engines to avoid the
complexity of tying emission standards to boat characteristics. A given
engine may be used in boats longer and shorter than 24 meters; engine
manufacturers generally will not know the size of the boat into which
an engine will be installed. Also, we expect that most recreational
boats will be under 24 meters in length. Chapter 4 of the Final
Regulatory Support Document provides further detail on the ISO E5 duty
cycle.
2. What Fuels Will Be Used During Emission Testing?
We are applying the same specifications for recreational marine
diesel engines that we established for commercial marine diesel
engines. That means that the recreational engines will use the same
test fuel that is required for testing Category 1 commercial marine
diesel engines, which is a regular nonroad test fuel with moderate
sulfur content. We are not aware of any difference in fuel
specifications for recreational and commercial marine engines of
comparable size.
3. How Does In-Use Testing Work?
In-use testing on marine engines may be used to ensure compliance
in use. This testing may include taking in-use marine engines out of
the vessel and testing them in a laboratory, as well as field testing
of in-use engines on the boat, in a marine environment.
We plan to use field-testing data in two ways. First, we may use it
as a screening tool, with follow-up laboratory testing over the ISO E5
duty cycle or NTE zone where appropriate. Second, we may use the data
directly as a basis for compliance determinations,
[[Page 68312]]
as long as field-testing equipment and procedures are capable of
providing reliable information from which conclusions can be drawn
regarding what emission levels would be with laboratory-based
measurements. Because it would likely be difficult to match the E5 test
points exactly on an engine in use on a vessel, NTE zone testing will
reduce the difficulty of in-use compliance determinations.
For marine engines that expel exhaust gases underwater or mix their
exhaust with water, manufacturers must equip engines with an exhaust
sample port where a probe can be inserted for in-use exhaust emission
testing. It is important that the location of this port allow a well-
mixed and representative sample of the exhaust. This provision is
intended to simplify in-use testing. In cases where the engine
manufacturer does not supply enough of the exhaust system to add a
sample port, the engine manufacturer would be required to provide
installation instructions for a sample port. Vessel manufacturers would
be required to follow this and any other emission-related installation
instructions.
One of the advantages of the not-to-exceed requirements will be to
facilitate in-use testing. This will allow us to perform compliance
testing in the field. As long as the engine is operating under steady-
state conditions in the NTE zone, we will be able to measure emissions
and compare them to the NTE limits. To assist in this testing, engines
with electronic controls will be required to broadcast engine torque
(as percent of maximum) and engine speed on their controller area
networks.
4. How Is the Maximum Test Speed Determined?
To ensure that a manufacturer's declared maximum speed is
representative of actual engine operating characteristics and is not
improperly used to influence the parameters under which their engines
are certified, we are applying the definition of maximum test speed
used for commercial marine engines. This definition of maximum test
speed is the single point on an engine's normalized maximum power
versus speed curve that lies farthest away from the zero-power, zero-
speed point.
In establishing this definition of maximum test speed, it was our
intent to specify the highest speed at which the engine is likely to be
operated in use. Under normal circumstances this maximum test speed
should be close to the speed at which peak power is achieved. However,
as some manufacturers indicated in their comments, it is possible under
this definition for the maximum test speed to be very different than
the speed at which peak power is achieved. This could result in the
certification test cycle and the NTE zone (which are both defined in
part by the maximum test speed) being unrepresentative of in-use
operation. Since we were aware of this potential during the development
of the commercial marine regulations, we included two provisions to
address issues such as these. First, Sec. 94.102 allows EPA to modify
test procedures in situations where the specified test procedures would
otherwise be unrepresentative of in-use operation. Thus, in cases in
which the definition of maximum test speed resulted in an engine speed
that was not expected to occur with in-use engines, we would work with
the manufacturers to determine the maximum speed that would be expected
to occur in-use.
Second, Sec. 94.106(c)(2) allows EPA to specify during
certification a broader NTE zone to include actual in-use operation. In
those cases where we could not specify a single maximum test speed
under Sec. 94.102 that would sufficiently cover the range of in-use
engine speeds, we would specify a broader NTE zone. For example, we
would generally expect that the NTE zone would include the peak power
point. If the maximum test speed derived under Sec. Sec. 94.102 and
94.107 resulted in an NTE zone that did not include the peak power
point, we would likely specify that the NTE zone be broadened to
include that point. Similarly, we would expect that a manufacturer's
advertised rated power/speed point should be within the NTE zone, and
could broaden the NTE zone to include that point as well.
E. Special Compliance Provisions
The provisions discussed here are designed to minimize regulatory
burdens on manufacturers needing added flexibility to comply with
emission standards. These manufacturers include engine dressers, small-
volume engine marinizers, and small-volume boat builders. Commenters
generally supported these provisions as proposed.
1. What Are the Burden Reduction Approaches for Engine Dressers?
Many recreational marine diesel engine manufacturers take a new,
land-based engine and modify it for installation on a marine vessel.
Some of the companies that modify an engine for installation on a boat
make no changes that might affect emissions. Instead, the modifications
may consist of adding mounting hardware and a generator or reduction
gears for propulsion. It can also involve installing a new marine
cooling system that meets original manufacturer specifications and
duplicates the cooling characteristics of the land-based engine, but
with a different cooling medium (such as sea water). In many ways,
these manufacturers are similar to nonroad equipment manufacturers that
purchase certified land-based nonroad engines to make auxiliary
engines. This simplified approach of producing an engine can more
accurately be described as dressing an engine for a particular
application. Because the modified land-based engines are subsequently
used on a marine vessel, however, these modified engines will be
considered marine diesel engines, which then fall under these
requirements.
To clarify the responsibilities of engine dressers under this rule,
we will not treat them as a manufacturer of a recreational marine
diesel engine and therefore they would not be required to obtain a
certificate of conformity, as long as they meet the following seven
conditions.
(1) The engine being dressed (the ``base'' engine) must be a
highway, land-based nonroad, or locomotive engine, certified pursuant
to 40 CFR part 86, 40 CFR part 89, or 40 CFR part 92, respectively, or
a marine diesel engine certified pursuant to this part.
(2) The base engine's emissions, for all pollutants, must meet the
otherwise applicable recreational marine emission limits. In other
words, starting in 2005, a dressed nonroad Tier 1 engine will not
qualify for this exemption, because the more stringent standards for
recreational marine diesel engines go into effect at that time.
(3) The dressing process must not involve any modifications that
can change engine emissions. We do not consider changes to the fuel
system to be engine dressing because this equipment is integral to the
combustion characteristics of an engine.
(4) All components added to the engine, including cooling systems,
must comply with the specifications provided by the engine
manufacturer.
(5) The original emissions-related label must remain clearly
visible on the engine.
(6) The engine dresser must notify purchasers that the marine
engine is a dressed highway, nonroad, or locomotive engine and is
exempt from the requirements of 40 CFR part 94.
(7) The engine dresser must report annually to us the models that
are exempt pursuant to this provision and such other information as we
deem
[[Page 68313]]
necessary to ensure appropriate use of the exemption.
Any engine dresser not meeting all these conditions will be
considered an engine manufacturer and will accordingly need to obtain a
certificate of conformity for these new engines, consistent with this
rule's provisions, and label the engine showing that it is available
for use as a marine engine.
An engine dresser violating the above criteria might be liable
under anti-tampering provisions for any change made to the land-based
engine that affects emissions. The dresser might also be subject to a
compliance action for selling new marine engines that are not certified
to the required emission standards. For an engine dresser complying
with the above provisions, the original certificate would remain in
effect and the certifier of the engine would remain liable for the
emissions performance of the engine.
2. What Special Provisions Is EPA Adopting for Small Entities?
In addition to provisions for engine dressers, we are also
finalizing special provisions designed to provide flexibility to small
entities. Prior to the proposal, we conducted an inter-agency Small
Business Advocacy Review Panel as described in Section XI.C. With input
from small-entity representatives, the panel drafted a report with
findings and recommendations on how to reduce the potential small-
business burden resulting from this rule. The inter-agency panel's
recommendations were proposed by EPA and are now being finalized as
proposed. The following sections describe these provisions.
3. What Are the Burden Reduction Approaches for Small-Volume Engine
Marinizers?
We are providing additional options for small-volume engine
marinizers. The purpose of these options is to reduce the burden on
companies for which fixed costs cannot be distributed over a large
number of engines. For this reason, we are defining a small-volume
engine manufacturer based on annual U.S. sales of engines and are
providing the additional options on this basis rather than on business
size in terms of number of employees, revenue, or other such measures.
The production count we are using includes all engines (automotive,
other nonroad, etc.) and not just recreational marine engines. We
consider recreational marine diesel engine manufacturers to be small
volume for purposes of this provision if they produce fewer than 1,000
internal combustion engines per year. Based on our characterization of
the industry, there is a natural break in production volumes above 500
engine sales where the next smallest manufacturers make tens of
thousands of engines. We chose 1,000 engines as a limit because it
groups together all the marinizers most needing relief, while still
allowing for reasonable sales growth.
The options for small-volume marinizers are discussed below.
a. Broaden engine families. We have established engine criteria for
distinguishing between engine families, which is intended to divide a
manufacturer's product line into multiple engine families. We are
allowing small-volume marinizers to put all of their models into one
engine family (or more as necessary) for certification purposes.
Marinizers would then certify using the ``worst-case'' configuration.
This approach is consistent with the option offered to post-manufacture
marinizers under the commercial marine regulations. The advantage of
this approach is that it minimizes certification testing because the
marinizer can use a single engine in the first year to certify their
whole product line. As for large companies, the small-volume
manufacturers could then carry-over data from year to year until
changing engine designs in a way that might significantly affect
emissions.
We understand that this option alone still requires a certification
test and the associated burden for small-volume manufactures. We
consider this to be the foremost cost concern for some small-volume
manufacturers, because the test costs are spread over low sales
volumes. Also, we recognize that it may be difficult to determine the
worst-case emitter without additional testing. We are requiring testing
because we need a reliable, test-based technical basis to issue a
certificate for these engines. Manufacturers will be able to use carry-
over to spread costs over multiple years of production.
b. Minimize compliance requirements. Production-line and
deterioration testing requirements do not apply to small-volume
marinizers. We will assign a deterioration factor for use in
calculating end-of-life emission factors for certification. The
advantages of this approach would be to minimize compliance testing.
Production-line and deterioration testing would be more extensive than
a single certification test.
c. Expand engine dresser flexibility. We are expanding the engine
dresser definition for small-volume marinizers to include water-cooled
turbochargers where the goal is to match the performance of the non
water-cooled turbocharger on the original certified configuration. We
believe this would provide more opportunities for diesel marinizers to
be excluded from certification testing if they operate as dressers.
d. Streamlined certification. We will allow small-volume marinizers
to certify to the not-to-exceed (NTE) requirements with a streamlined
approach. We believe small-volume marinizers can make a satisfactory
showing that they meet NTE standards with limited test data. Similar to
the standard NTE program, once these manufacturers test engines over
the five-mode certification duty cycle (E5), they can use those or
other test points to extrapolate the results to the rest of the NTE
zone. For example, an engineering analysis may consider engine timing
and fueling rate to determine how much the engine's emissions may
change at points not included in the E5 cycle. For this streamlined NTE
approach, keeping all four test modes of the E5 cycle within the NTE
standards will be enough for small-volume marinizers to certify
compliance with NTE requirements, as long as there are no significant
changes in timing or fueling rate between modes.
e. Delay standards for five years. Applying a five-year delay, the
standards take effect from 2011 to 2014 for small-volume marinizers,
depending on engine size. Marinizers may apply this five-year delay to
all or just a portion of their production. They may therefore still
sell engines that meet the standards when possible on some product
lines while delaying introduction of emission-control technology on
other product lines. This option provides more time for small
marinizers to redesign their products, allowing time to learn from the
technology development of the rest of the industry. Boat builders may
use these uncertified engines in their vessels.
While we are concerned about the loss of emission control from part
of the fleet during this time, we recognize the special needs of small-
volume marinizers and believe the added time may be necessary for these
companies to comply with emission standards. This additional time will
allow small-volume marinizers to obtain and implement proven, cost-
effective emission-control technology.
f. Hardship provisions. We are adopting two hardship provisions for
small-volume marinizers. Marinizers may apply for this relief on an
annual basis. First, small marinizers may petition us for additional
time to comply with the standards. The marinizer must show that it has
taken all possible steps to comply but the burden of compliance costs
will have a
[[Page 68314]]
major impact on the company's solvency. Also, if a certified base
engine is available, the marinizer must generally use this engine. We
believe this provision will protect small-volume marinizers from undue
hardship due to certification burden. Also, some emission reduction can
be gained if a certified base engine becomes available.
Second, small-volume marinizers may also apply for hardship relief
if circumstances outside their control caused the failure to comply
(such as a supply contract broken by parts supplier) and if failure to
sell the subject engines will have a major impact on the company's
solvency. We consider this relief mechanism to be an option of last
resort. We believe this provision will protect small-volume marinizers
from circumstances outside their control. We, however, intend to not
grant hardship relief if contract problems with a specific company
prevent compliance for a second time.
Although the inter-agency panel did not specify a time limit for
these hardship provisions, and we are not finalizing any such time
limits, we envision these hardship provisions as transitional in
nature. We would expect their use to be limited to the early years of
the program, in a similar time frame as we are establishing for the
recreational vehicle hardship provisions, as discussed in Section
VII.C.
4. What Are the Burden Reduction Approaches for Small-Volume Boat
Builders Using Recreational Marine Diesel Engines?
The inter-agency panel also recommended burden reduction approaches
for small-volume boat builders. The recommendations were based on the
concerns that, although boat builders are not subject to the engine-
based emission standards, they are required to use certified engines
and may need to redesign engine compartments on some boats if engine
designs were to change significantly. EPA proposed the flexibilities
recommended by the panel and are finalizing them as proposed.
We are adopting four options for small-volume vessel manufacturers
using recreational marine diesel engines. These options are intended to
reduce the burden on companies for which fixed costs cannot be
distributed over a large number of vessels. As proposed, we are
therefore defining a small-volume boat builder as one that produces
fewer than 100 boats for sale in the U.S. in one year and has fewer
than 500 employees. The production count includes all engine-powered
recreational boats. These options may be used at the manufacturer's
discretion. The options for small-volume boat builders are discussed
below.
a. Percent-of-production delay. Manufacturers with a written
request from a small-volume boat builder and prior approval from us may
produce a limited number of uncertified recreational marine diesel
engines. From 2006 through 2010, small-volume boat builders may
purchase uncertified engines to sell in boats for an amount equal to 80
percent of engine sales for one year. For example, if the small boat
builder sells 100 engines per year, a total of 80 uncertified engines
may be sold over the five-year period. This will give small boat
builders an option to delay using new engine designs for a portion of
business. Engines produced under this flexibility must be labeled
accordingly so that customs inspectors know which uncertified engines
can be imported. We continue to believe this approach is appropriate
and are finalizing it as proposed.
b. Small-volume allowance. This allowance is similar to the
percent-of-production allowance, but is designed for boat builders with
very small production volumes. The only difference with the above
allowance is that the 80-percent allowance described above may be
exceeded, as long as sales do not exceed either 10 engines per year or
20 engines over five years (2006 to 2010). This applies only to engines
less than or equal to 2.5 liters per cylinder.
c. Existing inventory and replacement engine allowance. Small-
volume boat builders may sell their existing inventory after the
implementation date of the new standards. However, no purposeful
stockpiling of uncertified engines is permitted. This provision is
intended to allow small boat builders the ability to turn over engine
designs.
d. Hardship relief provision. Small boat builders may apply for
hardship relief if circumstances outside their control caused the
problem (for example, if a supply contract were broken by the engine
supplier) and if failure to sell the subject vessels will have a major
impact on the company's solvency. This relief allows the boat builder
to use an uncertified engine and is considered a mechanism of last
resort. These hardship provisions are consistent with those currently
in place for post-manufacture marinizers of commercial marine diesel
engines.
F. Technical Amendments
The regulations include a variety of amendments to the programs
already adopted for marine spark-ignition and diesel engines, as
described in the following paragraphs.
1. 40 CFR Part 91: Outboards and Personal Watercraft
We have identified four principal amendments to the requirements
for outboard and personal watercraft engines. First, we are adding a
definition of United States which is ``the States, the District of
Columbia, the Commonwealth of Puerto Rico, the Commonwealth of the
Northern Mariana Islands, Guam, American Samoa, the U.S. Virgin
Islands, and the Trust Territory of the Pacific Islands.'' This
definition is consistent with that included in 40 CFR part 94 for
marine diesel engines. This is especially helpful in clearing up
questions related to U.S. territories in the Carribean Sea and the
Pacific Ocean. Second, we have found two typographical errors in the
equations needed for calculating emission levels in 40 CFR 91.419.
Third, we are adjusting the regulation language to clarify testing
rates for the in-use testing program. The regulations currently specify
a maximum rate of 25 percent of a manufacturer's engine families
subject to in-use testing. The revised language states that for
manufacturers with fewer than four engine families subject to in-use
testing, the maximum testing rate is one family per year in place of
the percentage calculation. Finally, we are revising the regulatory
provision prohibiting emission controls that lead to increases of
noxious or toxic compounds that would pose an unreasonable risk to the
public, as described in Section II.B.2.
2. 40 CFR Part 94: Commercial Marine Diesel Engines
We are adopting several regulatory amendments to the program for
commercial marine diesel engines. Many of these are straightforward
edits for correct grammar and cross references. We are also changing
the definition of United States, as described in the previous section.
We are adding a definition for spark-ignition, consistent with the
existing definition for compression-ignition, which will allow us to
define compression-ignition as any engine that is not spark-ignition.
This will help ensure that marine emission standards for the different
types of engines fit together appropriately.
The discussion of production-line testing in Section II.C.4
specifies reduced testing rates after two years of consistent good
performance. We are extending this provision to commercial marine
diesel engines as well.
[[Page 68315]]
The test procedures for Category 2 marine engines give a cross-
reference to 40 CFR part 92, which defines the procedures for testing
locomotives and locomotive engines. Part 92 specifies a wide range of
ambient temperatures for testing, to allow for outdoor measurements. We
expect all testing of Category 2 marine engines to occur indoors and
are therefore adopting a range of 13[deg]
to 30[deg]
C (55[deg] to
86[deg]
F) for emission testing.
Finally, we are revising the regulatory provision prohibiting
emission controls that lead to increases of noxious or toxic compounds
that would pose an unreasonable risk to the public, as described in
Section II.B.2.
G. Technological Feasibility
We have concluded that the emission-reduction strategies expected
for land-based nonroad diesel engines and commercial marine diesel
engines can also be applied to recreational marine diesel engines, such
that these emission reductions strategies will provide compliance with
recreational marine diesel emission standards. Marine diesel engines
are generally derivatives of land-based nonroad and highway diesel
engines. Marine engine manufacturers and marinizers make modifications
to the engine to make it ready for use in a vessel. These modifications
can range from basic engine mounting and cooling changes to a
restructuring of the power assembly and fuel management system.
Chapters 3 and 4 of the Final Regulatory Support Document discuss this
process in more detail. Also, we have collected emission data
demonstrating the feasibility of the steady state average standard and
not-to-exceed requirements. These data are presented in Chapter 4 of
the Final Regulatory Support Document.
1. Implementation Schedule
For recreational marine diesel engines, the implementation schedule
allows an additional two years of delay beyond the commercial marine
diesel standards. This represents up to a five-year lead time relative
to the implementation dates of the land-based nonroad standards. This
allows time for the carryover of technology from land-based nonroad and
commercial marine diesel engines. In addition, these implementation
dates represent three to six years of lead time beyond publication of
this final rule.
2. Standard Levels
Marine diesel engines are typically derived from or use the same
technology as land-based nonroad and commercial marine diesel engines
and should therefore be able to effectively use the same emission-
control strategies. In fact, recreational marine engines can better use
the water they operate in as a cooling medium compared with commercial
marine, because they are able to use raw-water aftercooling. This can
help them reduce charge-air intake temperatures more easily than the
commercial models and much more easily than land-based nonroad diesel
engines. Cooling the intake charge reduces the formation of
NOX emissions and thus indirectly enables other HC and PM
control strategies. As a result, baseline recreational engines
generally have lower NOX emissions than uncontrolled
commercial marine engines. Therefore, we believe that recreational
marine engines can meet the same standard levels as are in place for
commercial marine engines without sacrificing power or increasing
weight of the engine.
3. Technological Approaches
We anticipate that manufacturers will meet the new emission
standards for recreational marine diesel engines primarily with
technology that will be applied to land-based nonroad and commercial
marine diesel engines. Much of this technology has already been
established in highway applications and is being used in limited land-
based nonroad and marine applications. Our analysis of this technology
is described in detail in Chapters 3 and 4 of the Final Regulatory
Support Document and is summarized here.
By adopting standards that don't go into place until 2006, we are
providing engine manufacturers with substantial lead time for
developing, testing, and implementing emission-control technologies.
This lead time and the coordination of standards with those for land-
based nonroad engines allows time for a comprehensive program to
integrate the most effective emission-control approaches into the
manufacturers' overall design goals related to durability, reliability,
and fuel consumption.
Engine manufacturers have already produced limited numbers of low-
NOX marine diesel engines. More than 80 of these engines
have been placed into service in California through demonstration
programs. Through the demonstration programs, we were able to gain some
insight into what technologies can be used to meet the new emission
standards. Chapter 4 presents data on 25 of these engines tested over
the E5 duty cycle. Although only one of these engines has been shown to
meet the HC+NOX and PM standards, many of these engines are
well below either the HC+NOX or PM standards or are close to
meeting both. With further optimization, we believe these engine
designs can be used to meet the exhaust emission standards for
recreational marine diesel engines.
Highway engines have been the leaders in developing new emission-
control technology for diesel engines. Because of the similar engine
designs in land-based nonroad and marine diesel engines, it is clear
that much of the technological development that has led to lower-
emitting highway engines can be transferred or adapted for use on land-
based nonroad and marine engines. Much of the improvement in emissions
from these engines comes from ``internal'' engine changes such as
variation in fuel-injection variables (injection timing, injection
pressure, spray pattern, rate shaping), modified piston bowl geometry
for better air-fuel mixing, and improvements intended to reduce oil
consumption. Introduction and ongoing improvement of electronic
controls have played a vital role in facilitating many of these
improvements.
Turbocharging is widely used now in marine applications, especially
in larger engines, because it improves power and efficiency by
compressing the intake air. Turbocharging may also be used to decrease
particulate emissions in the exhaust. Today, marine engine
manufacturers generally have to rematch the turbocharger to the engine
characteristics of the marine version of a nonroad engine and often
will add water jacketing around the turbocharger housing to keep
surface temperatures low. Once the nonroad Tier 2 engines are available
to the marine industry, matching the turbochargers for the engines will
be an important step in achieving low emissions.
Aftercooling is a well established technology for reducing
NOX by decreasing the temperature of the charge air after it
has been heated during compression. Decreasing the charge-air
temperature directly reduces the peak cylinder temperature during
combustion, which is the primary cause of NOX formation.
Air-to-water and water-to-water aftercoolers are well established for
land-based applications. For engines in marine vessels, there are two
different types of aftercooling: jacket-water and raw-water
aftercooling. With jacket-water aftercooling, the fluid that extracts
heat from the aftercooler is itself cooled by ambient water. This
cooling circuit may either be the same circuit used to cool the engine
or it may be a separate circuit. By incorporating a separate circuit,
marine engine
[[Page 68316]]
manufacturers can further reduce charge-air temperatures. This separate
circuit can result in even lower temperatures with raw water as the
coolant. This means that ambient water is pumped directly to the
aftercooler. Raw-water aftercooling is currently widely used in
recreational applications. Because of the access that marine engines
have to a large ambient water cooling medium, we anticipate that marine
diesel engine manufacturers will largely reduce NOX
emissions with aftercooling.
Electronic controls also offer great potential for improved control
of engine parameters for better performance and lower emissions. Unit
pumps or injectors allow higher-pressure fuel injection with rate
shaping to carefully time the delivery of the whole volume of injected
fuel into the cylinder. Marine engine manufacturers can take advantage
of modifications to the routing of the intake air and the shape of the
combustion chamber of nonroad engines for improved mixing of the fuel-
air charge. Separate-circuit aftercooling (both jacket-water and raw-
water) will likely gain widespread use in turbocharged engines to
increase performance and lower NOX.
Fuel injection changes and other NOX control strategies
typically reduce engine noise, sometimes dramatically. One important
source of noise in diesel combustion is the sound associated with the
combustion event itself. When a premixed charge of fuel and air
ignites, the very rapid combustion leads to a sharp increase in
pressure, which is easily heard and recognized as the characteristic
sound of a diesel engine. The conditions that lead to high noise levels
also cause high levels of NOX formation.
The impact of the new emission standards on energy is measured by
the effect on fuel consumption from complying engines. Many of the
marine engine manufacturers are expected to retard engine timing which
increases fuel consumption somewhat. Most of the technology changes
anticipated in response to the new standards, however, have the
potential to reduce fuel consumption as well as emissions. Redesigning
combustion chambers, incorporating improved fuel injection systems, and
introducing electronic controls provide the engine designer with
powerful tools for improving fuel efficiency while simultaneously
controlling emission formation. To the extent that manufacturers add
aftercooling to non aftercooled engines and shift from jacket-water
aftercooling to raw-water aftercooling, there will be a marked
improvement in fuel-efficiency. Manufacturers of highway diesel engines
have been able to steadily improve fuel efficiency even as new emission
standards required significantly reduced emissions.
There are no apparent safety issues associated with the new
emission standards. Marine engine manufacturers will likely use only
proven technology that is currently used in other engines such as
nonroad land-based diesel applications, locomotives, and diesel trucks.
The main technological approach will likely be optimization and
calibration of their fuel injection and air management systems.
4. Our Conclusions
The new emission standards for recreational marine diesel engines
reasonably reflect what manufacturers can achieve through the
application of available technology to current recreational marine
diesel engines. Recreational marine engine manufacturers will need to
use the available lead time to develop the necessary emission-control
strategies, including transfer of technology from land-based nonroad
and commercial marine diesel engines. This development effort will
require not only achieving the targeted emission levels, but also
ensuring that each engine will meet all performance and emission
requirements over its useful life. As discussed in Section IX, the new
standards represent significant reductions compared with baseline
emission levels.
Based on information currently available, we conclude it is
feasible for recreational marine diesel engine manufacturers to meet
the new emission standards using combinations of technological
approaches discussed above and in Chapters 3 and 4 of the Final
Regulatory Support Document. While the technologies described above are
expected to yield the full degree of emission reduction anticipated, it
is possible that manufacturers may also rely on a modest degree of
fuel-injection timing retard as a strategy for complying with emission
standards. This is due to variations in engine designs and baseline
injection timing. For instance, an engine with very advanced injection
timing in its baseline configuration would likely need to employ some
timing retard to meet the standards.
The transfer of technology from land-based nonroad and commercial
marine engines is an important factor in our determination that the
recreational marine diesel engine standards are feasible. Most marine
diesel engine models also serve in land-based applications. Sales of
land-based versions of these engines are usually much greater than
those of the marine counterpart versions, so manufacturers typically
focus their primary technology development efforts on their land-based
products. Manufacturers then modify these engines for use in marine
applications. These changes can be extensive, but they rarely involve
basic R&D for new technologies. We do not anticipate the use of
advanced technology such as particulate filters and NOX
adsorbers on trucks until the 2007 time frame. Therefore, we do not
believe that it would be appropriate to implement standards, at this
time, that would require the use of advanced technology that has yet to
be developed for the higher volume land-based diesel engine market. We
would, however, consider this technology in the future for setting
further tiers of marine engine emission standards.
In addition, we have incorporated various options that will permit
marinizers and boat builders to respond to engine changes in an orderly
way. We expect that meeting these requirements will pose a challenge,
but one that is feasible taking into consideration the availability and
cost of technology, time, noise, energy, and safety.
VII. General Nonroad Compliance Provisions
This section describes a wide range of compliance provisions that
apply generally to all the spark-ignition engines and vehicles subject
to the new emission standards. Several of these provisions apply not
only to manufacturers and importers, but also to equipment
manufacturers installing certified engines, remanufacturing facilities,
operators, and others.
The regulatory text for the compliance requirements for Large SI
engines and recreational vehicles are in a new Part 1068 of Title 40,
entitled ``General Compliance Programs for Nonroad Engines.'' The
compliance provisions for recreational marine diesel engines are
generally the same as those already adopted for commercial marine
diesel engines (40 CFR part 94).
The following discussion of the general nonroad provisions follows
the regulatory text. For ease of reference, the subpart designations
for 40 CFR part 1068 are provided. Where different provisions apply to
the marine engines, we note those differences in this section.
A. Miscellaneous Provisions (Part 1068, Subpart A)
This subpart contains general provisions to define terms and the
scope of application for all of 40 CFR part
[[Page 68317]]
1068. Other provisions concern how we handle confidential information,
how the EPA Administrator delegates decision-making authority, and when
we may inspect a manufacturer's facilities, engines, or records.
The process of testing engines and preparing an application for
certification requires the manufacturer to make a variety of judgments.
This includes, for example, selecting test engines, operating engines
between tests, and developing deterioration factors. The regulations
describe the methodology we use to evaluate concerns related to how
manufacturers use good engineering judgment in cases where the
manufacturer has such discretion (see 40 CFR 1068.5 and 40 CFR 94.221).
If we find a problem in these areas, we will take into account the
degree to which any error in judgment was deliberate or in bad faith.
This subpart is consistent with provisions already adopted for light-
duty highway vehicles and commercial marine diesel engines.
B. Prohibited Acts and Related Requirements (Part 1068, Subpart B)
The provisions in this subpart establish a set of prohibitions for
engine manufacturers (including importers), equipment manufacturers,
operators, engine rebuilders, and owners/operators to ensure that
engines meet the emission standards. These provisions are intended to
help ensure that each new engine sold or otherwise entered into
commerce in the United States is certified to the relevant standards,
that it remains in its certified configuration throughout its lifetime,
and that only certified engines are used in the appropriate nonroad
equipment.
1. General Prohibitions (Sec. 1068.101)
This regulation contains several prohibitions consistent with the
Clean Air Act. No one may sell a new engine subject to the emission
standards (or equipment containing such an engine) in the United States
without a valid certificate of conformity issued by EPA, deny us access
to relevant records, or keep us from entering a facility to test or
inspect engines. In addition, no one may remove or disable a device or
design element that may affect an engine's emission levels, or
manufacture any device that will make emission controls ineffective,
which we consider tampering. Other prohibitions reinforce
manufacturers' obligations to meet various certification requirements.
We also prohibit selling engine parts that prevent emission-control
systems from working properly. Finally, for engines that are excluded
because they are used in applications not covered by these regulations
(for example, stationary or solely for competition), we generally
prohibit using these engines in regulated applications.
These prohibitions are the same as those that apply to other
engines we have regulated in previous rulemakings. Each prohibited act
has a corresponding maximum penalty as specified in Clean Air Act
section 205. As provided for in the Federal Civil Penalties Inflation
Adjustment Act of 1990, Pub. L. 10-410, these maximum penalties are
periodically adjusted by regulation to account for inflation. The
current penalty amount for each violation is $31,500.\85\
---------------------------------------------------------------------------
\85\ EPA acted to adjust the maximum penalty amount in 1996 (61
FR 69364, December 31, 1996) and 2002 (67 FR 41343, June 18, 2002).
See also 40 CFR part 19.
---------------------------------------------------------------------------
2. Equipment Manufacturer Provisions (Sec. 1068.105)
Equipment manufacturers may not sell new equipment with uncertified
engines once the emission standards begin to apply. We allow a grace
period for equipment manufacturers to use up their supply of
uncertified engines, as long as they follow their normal inventory
practices for buying engines.
We require equipment manufacturers to observe the engine
manufacturers' emission-related installation specifications to ensure
that the engine remains in its certified configuration. This may
include such things as radiator specifications, placement of catalytic
converters, diagnostic signals and interfaces, and steps to minimize
evaporative emissions.
If equipment manufacturers install a certified engine in a way that
obscures the engine label, they must add a duplicate label on the
equipment.
If equipment manufacturers don't fulfill the responsibilities we
describe in this section, we consider them to be violating one or more
of the prohibited acts described above.
3. In-Service Engines (Sec. 1068.110)
The regulations prevent manufacturers from requiring owners to use
any certain brand of aftermarket parts and give the manufacturer
responsibility for engine servicing related to emissions warranty,
leaving the responsibility for all other maintenance with the owner.
This regulation also reserves our right to do testing (or require
testing) to determine compliance with emission standards and
investigate potential defeat devices, as authorized by the Act.
4. Engine Rebuilding (Sec. 1068.120)
We are establishing rebuild provisions for all the nonroad engines
subject to the emission standards in this final rule. This approach is
similar to what applies to heavy-duty highway engines, nonroad diesel
engines, and commercial marine diesel engines. This is necessary to
prevent an engine rebuilder from rebuilding engines in a way that
disables the engine's emission controls or compromises the
effectiveness of the emission-control system. For businesses involved
in commercial engine rebuilding, we are adopting minimal recordkeeping
requirements so rebuilders can show that they comply with regulations.
In general, we require anyone rebuilding a certified engine to
restore it to its original (or a lower-emitting) configuration. We are
adding unique requirements for rebuilders to replace some critical
emission-control components such as fuel injectors and oxygen sensors
in all rebuilds for engines that use those technologies, unless there
is reason to believe that those components are still working properly.
We also require that rebuilders replace an existing catalyst if there
is evidence that it is not functional; for example, if a catalyst has
lost its physical integrity with loose pieces rattling inside, it would
need to be replaced.
The rebuilding provisions define good rebuilding practices to avoid
violating the prohibition on ``removing or disabling'' emission-control
systems. We are therefore extending these provisions to individuals who
rebuild their own engines, but without any recordkeeping requirements.
C. Exemptions (Part 1068, Subpart C)
We are including several exemptions for certain specific
situations. Most of these are consistent with previous rulemakings. We
highlight the new or different provisions in the following paragraphs.
In general, exempted engines must comply with the requirements only in
the sections related to the exemption. Note that additional
restrictions may apply to importing exempted engines (see Section
VII.D). Also, we may require manufacturers (or importers) to add a
permanent label describing that the engine is exempt from emission
standards for a specific purpose. In addition to helping us enforce
emission standards, this helps ensure that imported engines clear
Customs without difficulty.
[[Page 68318]]
1. Testing
Anyone may request an exemption for engines used only for research
or other investigative purposes.
2. Manufacturer-Owned Engines
Engines that are used by engine manufacturers for development or
marketing purposes may be exempted from regulation if they are
maintained in the manufacturers' possession and are not used for any
revenue-generating service.
3. Display Engines
Anyone may request an exemption for engines intended for only for
display.
4. National Security
In general, engines installed in combat-related equipment are
exempt from emission standards. In addition, engine manufacturers may
request and receive an exemption for other engines if they are needed
by an agency of the federal government responsible for national
defense. The request for exemptions in these cases must include the
endorsement of the procuring government agency.
5. Exported Engines
Engines that will be exported to countries that don't have the same
emission standards as those that apply in the United States are
exempted without a request. This exemption is not available if the
destination country has the same emission standards as those in the
United States.
6. Competition Engines
New engines used solely for competition are generally excluded or
exempted from regulations that apply to nonroad engines. For purposes
of our certification requirements, manufacturers receive an exemption
if they can show that they produce an engine model specifically for use
solely in competition. In addition, engines that have been modified for
use in competition are exempt from the prohibition against tampering
described above (without need for request). The literal meaning of the
term ``used solely for competition'' would apply for these
modifications. We therefore do not allow anyone to use the engine for
anything other than competition once it has been modified. This also
applies to someone who later buys the engine, so we require the person
modifying the engine to remove or deface the original engine label and
inform a subsequent buyer in writing of the conditions of the
exemption.
7. Replacement Engines
An exemption is available to engine manufacturers without request
if that is the only way to replace an engine from the field that was
produced before the current emission standards took effect. If less
stringent standards applied to the old engine when it was new, the
replacement engine must at a minimum meet those standards.
8. Hardship Related to Economic Burden
There are two types of hardship provisions. The first type of
hardship program allows small businesses to petition EPA for up to
three years of additional lead time to comply with the standards. A
small manufacturer must demonstrate that it has taken all possible
business, technical, and economic steps to comply but the burden of
compliance costs will have a significant impact on the company's
solvency. A manufacturer must provide a compliance plan detailing when
and how it will achieve compliance with the standards. Hardship relief
may include requirements for reducing emission on an interim basis and/
or purchasing and using emission credits. The length of the hardship
relief decided during review of the hardship application may be up to
one year, with the potential to extend the relief as needed. The second
hardship program allows companies to apply for hardship relief if
circumstances outside their control cause the failure to comply (such
as a supply contract broken by parts supplier) and if the failure to
sell the subject engines will have a major impact on the company's
solvency. We would, however, not grant hardship relief if contract
problems with a specific company prevent compliance for a second time.
9. Hardship for Equipment Manufacturers
Equipment manufacturers in many cases depend on engine
manufacturers to supply certified engines in time to produce complying
equipment by the date emission standards begin to apply. This is
especially true for industrial and marine applications. In other
programs, equipment manufacturers have raised concerns of certified
engines being available too late for equipment manufacturers to
adequately accommodate changing engine size or performance
characteristics. To address this concern, in unusual circumstances,
equipment manufacturers may request up to one extra year before using
certified engines if they are not at fault and will face serious
economic hardship without an extension.
In addition, we are aware that some manufacturers of nonroad
engines are dependent on another engine manufacturer to supply base
engines that are then modified for the final application. Much like
equipment manufacturers, these ``secondary engine manufacturers'' may
face difficulty in producing certified engines if the manufacturer
selling the base engine makes an engine model unavailable with short
notice. These secondary manufacturers generally each buy a relatively
small number of engines and would therefore not necessarily be able to
influence the marketing or sales practices of the engine selling the
base engines. In this rulemaking, this is of particular concern for
Large SI engine manufacturers subject to new standards in 2004. As a
result, we are allowing secondary engine manufacturers to sell
uncertified engines or engines certified at emission levels above the
standard for a short period after emission standards begin to apply.
However, these companies control the final design of the engines, so we
would not approve any exemption unless the manufacturer committed to a
plan to make up for any calculated loss in environmental benefit. For
example, based on an alternate compliance level for 2004 model year
engines, we could calculate the number of 2006 model year engines that
would need to be certified early to the 2007 emission standards.
Provisions similar to these were adopted for commercial marine diesel
engines and will apply equally to recreational marine diesel engines.
See the regulatory text in 40 CFR 1068.255 and 40 CFR 94.209 for
additional information.
D. Imports (Part 1068, Subpart D)
In general, the same certification requirements apply to engines
and equipment whether they are produced in the U.S. or are imported.
This regulation also includes some additional provisions that apply if
someone wants to import an exempted or excluded engine. For example,
the importer needs appropriate documentation before importing
nonconforming engines; this is true even if an exemption for the same
reason doesn't require approval for engines produced in the U.S. These
declaration forms are available on the Internet at http://www.epa.gov/
OMS/imports/ or by phone at 202-564-9660.
All the exemptions described above for new engines also apply to
importation, though some of these apply only on a temporary basis. If
we approve a temporary exemption, it is available
[[Page 68319]]
only for a defined period and could require the importer to post bond
while the engine is in the U.S. There are several additional exemptions
that apply only to imported engines.
--Identical configuration: This is a permanent exemption to allow
individuals to import engines that were designed and produced to meet
applicable emission standards. These engines may not have the emission
label only because they were not intended for sale in the United
States. This exemption applies to all the engines covered by 40 CFR
part 1068.
--``Antique'' engines: We generally treat used engines as new if they
are imported without a certificate of conformity. However, this
permanent exemption allows for importation of uncertified engines if
they are more than 20 years old and still in their original
configuration.
--Repairs or alterations: This is a temporary exemption to allow
companies to repair or modify engines. This exemption does not allow
for operating the engine, except as needed to do the intended work.
--Diplomatic or military: This is a temporary exemption to allow
diplomatic or military personnel to use uncertified engines during
their term of service in the U.S.
--Engines subject to other programs: This is a temporary exemption that
allows someone to import an uncertified engine that will be converted
for use in a different application. For example, someone may want to
import a land-based nonroad engine to modify it and eventually sell it
as a marine engine. This exemption expires when the engine
modifications are complete, since one of the following scenarios will
apply (1) the company modifying the engine will modify the engine to
meet emission standards that apply to the modified engine, (2) the
company will have a valid exemption under the program that applies to
the modified engine, or (3) the modified engine will not be subject to
emission standards, in which case an exemption is no longer necessary.
E. Selective Enforcement Audit (Part 1068, Subpart E)
Clean Air Act section 206(b) gives us the discretion in any program
with vehicle or engine emission standards to do selective enforcement
auditing of production engines. In selective enforcement auditing, we
choose an engine family and give the manufacturer a test order
detailing a testing program to show that production-line engines meet
emission standards. The regulation text describes the audit procedures
in greater detail.
We intend generally to rely on manufacturers' testing of
production-line engines to show that their production process is
producing engines in compliance they comply with emission standards.
However, we reserve our right to do selective enforcement auditing if,
for example, we have reason to question the emission testing conducted
and reported by the manufacturer.
F. Defect Reporting and Recall (Part 1068, Subpart F)
In Part 1068, Subpart F, we are adopting defect reporting
requirements that obligate manufacturers to tell us when they learn
that emission control systems are defective and to conduct
investigations under certain circumstances to determine if an emission-
related defect is present. We are also requiring that manufacturers use
warranty information, parts shipments, and any other information which
may be available to trigger these investigations. For the purpose of
this subpart, we are considering defective any part or system that does
not function as originally designed for the regulatory useful life of
the engine or the scheduled replacement interval specified in the
manufacturer's maintenance instructions. For recreational vehicles and
nonroad spark-ignition engines over 19 kW, this approach to defect
reporting takes into account the varying sales volumes of the different
products.
We believe the investigation requirement in this rule will allow
both EPA and the engine manufacturers to fully understand the
significance of any unusually high rates of warranty claims and parts
replacement for systems or parts that may have an impact on emissions.
We believe that any prudent and responsible engine manufacturer would,
and should, conduct a thorough investigation as part of its normal
product quality practices when in possession of data indicating an
usually high number of recurring parts failures.
In the past, defect reports were submitted based on a very low
threshold with the same threshold applicable to all size engine
families and with little information about the full extent of the
problem. The new approach should result in fewer overall defect reports
being submitted by manufacturers than would otherwise be required under
the old defect reporting requirements because the number of defects
triggering the submission requirement rises with the engine family
size.
The defect reporting requirements under other vehicle and engine
regulations do not explicitly require investigations or reporting based
on information available to the manufacturer about warranty claims or
parts shipments. Such information is valuable and readily available to
most manufacturers and should be considered when determining whether or
not there is a defect of an emission-related part.
We are aware that counting warranty claims and part shipments will
likely include many claims that are not emission-related or that do not
represent defects, so we are establishing a relatively high threshold
for triggering the manufacturer's responsibility to investigate whether
there is in fact a real occurrence of an emission-related defect.
Manufacturers are not required to count towards the investigation
threshold any replacement parts they require to be replaced during the
useful life, as specified in the application for certification and
maintenance instructions to the owner, because such part shipments
clearly do not represent defects.
Subpart F is intended to require manufacturers to use information
we would expect them to keep in the normal course of business. We
believe in most cases manufacturers will not be required to institute
new programs or activities to monitor product quality or performance. A
manufacturer that does not keep warranty or replacement part
information may ask for our approval to use an alternate defect-
reporting methodology that is at least as effective in identifying and
tracking potential emissions related defects as the requirements of
subpart F. However, until we approve such a request, the thresholds and
procedures of subpart F continue to apply.
For engines with rated power below 560 kW, the investigation
thresholds in 40 CFR 1068.501 are 4 percent of total production, or
4,000 engines, whichever is less, for any single engine family in one
model year. The thresholds are reduced by 50 percent for defects
related to aftertreatment devices, because these components typically
play such a significant role in controlling engine emissions. For
example, for an engine family with a sales volume of 20,000 units in a
given model year, the manufacturer must investigate for emission-
related defects if there were warranty claims for replacing electronic
control units in 800 or more engines or catalytic converters on 400 or
more engines. For a family with sales volume of 200,000 units in a
given model year, the manufacturer
[[Page 68320]]
must investigate for emission-related defects if there were warranty
claims for replacing electronic control units in 4,000 or more engines
or catalytic converters on 2,000 or more engines.
For engines rated above 560 kW, each engine emits much greater
levels of emissions, both because of the higher power rating and the
fact that these engines generally operate at high load and for long
periods. In addition, the engine family for such engines are typically
of smaller volume compared to the lower power engines. We are therefore
adopting a requirement that manufacturers investigate defects for these
engines if they learn of 5 or more defects that may be emission-
related, or 1 percent of total production, whichever is greater.
The second threshold in 40 CFR 1068.501 specifies when a
manufacturer must report that there is an emission-related defect. This
threshold involves a smaller number of engines because each possible
occurrence has been screened to confirm that it is an emission-related
defect. In counting engines to compare with the defect-reporting
threshold, the manufacturer must consider a single engine family and
model year. However, when a defect report is required, the manufacturer
must report all occurrences of the same defect in all engine families
and all model years. For engines with rated power below 560 kW, the
threshold for reporting a defect is 0.25 percent of total production
for any single engine family, or 250 defects, whichever is less. The
thresholds are reduced 50 percent for reporting defects related to
aftertreatment devices. For engines with rated power greater than
560kW, the threshold for reporting defects is 0.5 percent of total
production, or 2 engines, whichever is greater.
If the number of engines with a specific defect is found to be less
than the threshold for submitting a defect report, but information,
such as warranty or parts shipment data, later indicates that there may
be additional defective engines, all the information must be considered
in determining whether the threshold for submitting a defect report has
been met. If a manufacturer has actual knowledge from any source that
the threshold for submitting a defect report has been met, a defect
report must be submitted even if the trigger for investigating has not
yet been met. For example, if manufacturers receive from their dealers,
technical staff or other field personnel information showing
conclusively that there is a recurring emission-related defect, they
must submit a defect report.
At specified times the manufacturer must also report the open
investigations as well as recently closed investigations that did not
require a defect report. One manufacturer indicated that investigations
of potential defects can sometimes take a long time. We agree and,
therefore, are not specifying a time limit for manufacturers to
complete their investigations. The periodic reports required by the
regulations, however, will allow us to monitor these investigations and
determine if it is necessary or appropriate for us to take further
action.
In general, we believe this updated approach to defect reporting
will decrease the number of defect reports submitted by manufacturers
overall while significantly improving their quality and their value to
both EPA and the manufacturer.
We are adopting the defect-reporting requirements for recreational
marine diesel engines that already apply to Category 1 commercial
marine diesel engines (40 CFR 94.403). In general, this requires the
manufacturer to report to us if they learn that 25 or more models have
a specific defect, without considering what percentage of the total
engines that represents. This applies to the occurrence of the same
defect and is not constrained by engine family or model year. We
believe it would not be appropriate to have different defect-reporting
requirements for different types of marine diesel engines, so we are
not adopting the defect-reporting provisions described above for
recreational marine diesel engines at this time. In the future we may
consider whether the defect-reporting methodology described above
should apply to recreational and commercial marine diesel engines.
Under Clean Air Act section 207, if we determine that a substantial
number of engines within an engine family, though properly used and
maintained, do not conform to the appropriate emission standards, the
manufacturer will be required to conduct a recall of the noncomplying
engine family to remedy the problem. However, we also recognize the
practical difficulty in implementing an effective recall program for
nonroad engines. It may be difficult to properly identify all the
affected owners absent a nationwide registration requirement similar to
that for cars and trucks. The response rate for affected owners or
operators to an emission-related recall notice is also a critical issue
to consider. We recognize that in some cases, recalling noncomplying
nonroad engines may not achieve sufficient environmental protection, so
our intent in such situations is generally to allow manufacturers to
nominate alternative remedial measures to address most potential
noncompliance situations. We expect that successful implementation of
appropriate alternative remediation would obviate the need for us to
make a determination of substantial nonconformity under section 207 of
the Act. Alternatives nominated by a manufacturer will be evaluated
based on the following criteria. The alternatives should--
(1) Represent a new initiative that the manufacturer was not
otherwise planning to perform at that time, with a clear connection to
the emission problem demonstrated by the engine family in question;
(2) Cost more than foregone compliance costs and consider the time
value of the foregone compliance costs and the foregone environmental
benefit of the engine family;
(3) Offset at least 100 percent of the emission exceedance relative
to that required to meet emission standards (or Family Emission
Limits); and
(4) Be possible to implement effectively and expeditiously and to
complete in a reasonable time.
These criteria, and any other appropriate factors, will guide us in
evaluating projects to determine whether their nature and burden is
appropriate to remedy the environmental impact of the nonconformity.
G. Hearings (Part 1068, subpart G)
Manufacturers have the opportunity to challenge our decisions
related to implementing this final rule. We are adopting hearing
procedures consistent with those currently in place for highway engines
and vehicles.
VIII. General Test Procedures
This rule establishes new engine testing regulations in 40 CFR part
1065. These regulations will apply to anyone who tests engines to show
that they meet the emission standards for snowmobiles, ATV,
motorcycles, or Large SI engines. This includes certification testing,
as well as all production-line and in-use testing. See the program
descriptions above for testing provisions that are unique to different
engine categories. The regulatory text in 40 CFR part 1065 is written
recognizing that we may someday apply these procedures more broadly to
other EPA engine testing programs. If we decide to apply these
provisions to other engines in future rulemaking, we would incorporate
necessary additions or changes at that time. Recreational marine diesel
engines
[[Page 68321]]
must be tested using the procedures already adopted in 40 CFR part 94.
A. General Provisions
As we have done in previous programs, we are adopting specific test
procedures to define how to measure emissions, but allow alternate
procedures if they are shown to be equivalent to our specified
procedures. The test procedures in 40 CFR part 1065 are derived from
our test procedures in 40 CFR part 86 for highway heavy-duty gasoline
engines and light-duty vehicles. The procedures have been simplified
(and to some extent generalized) to better fit nonroad engines.
B. Laboratory Testing Equipment
The regulations do not specify the type of engine or chassis
dynamometer to use during testing. Rather, they include performance
criteria that must be met during each test. These criteria are intended
to ensure that deviations from the specified speed and load duty cycle
are small.
Measuring emissions during transient operation calls for a greater
degree of sophistication than steady-state testing. For chassis testing
of recreational vehicles, we are adopting the specifications
established in 40 CFR part 86 for highway engines. For Large SI
engines, we based the dynamometer specifications around the
capabilities of current dynamometers with enhanced control
capabilities. While EPA confirmatory testing with transient duty cycles
must meet the prescribed specifications, manufacturers may ask for
approval to run tests with relaxed requirements for following the trace
of the transient duty cycle. Manufacturers would have an incentive to
accurately reproduce the test cycle to ensure compliance with emission
standards, but would be able to use otherwise invalidated tests if the
degree of variance from the test cycle does not call into question the
engine's reported emission levels.
In addition, for transient testing with recreational vehicles and
any testing with Large SI engines, the regulations specify that
emissions must be measured using a full-dilution constant-volume
sampler (CVS) like those used to measure emissions from highway
engines. This means that during a test, an engine's exhaust is routed
into a dilution tunnel where it is mixed with air and then sampled
using a bag sampler system. After the test, the concentrations of HC,
CO, and NOX in the bag is measured using conventional
laboratory analyzers.
For Large SI engines and snowmobiles, the steady-state test
procedures specify measuring emissions with dilute-sampling equipment.
Some manufacturers have expressed a preference to continue with their
established practice of using raw-sampling equipment and procedures.
While we believe dilute-sampling is most appropriate for these engines,
the provisions for alternate testing procedures may allow for raw-
sampling measurements for steady-state testing. As specified in 40 CFR
1065.10(c)(3) of the regulations, we allow manufacturers to use
alternate procedures shown to be equivalent to the specified
procedures. We are also including an interim provision for snowmobiles
to allow manufacturers to use the raw-sampling procedures in 40 CFR
part 91 for a few years before they are required to show equivalence
with the dilute-sampling procedures. This option will allow
manufacturers to focus their engineering efforts on reducing emissions
during the start of the program.
C. Laboratory Testing Procedures
The specific procedures for running emission tests are outlined
briefly here, with a more detailed description of the most significant
aspects. Before testing the engine, it is necessary to operate it
enough to stabilize emission levels or to make it more representative
of in-use engines. This is called service accumulation and may take one
of two forms. In the first method, a new engine is operated for up to
50 hours as a break-in period. This is done for most or all emission-
data engines. The second method is much longer, up to the full useful
life, and is done to determine deterioration factors.
Once an engine is ready for testing, it is connected to the
dynamometer with its exhaust flowing into the dilution tunnel. The
dynamometer is controlled to make the engine follow the specified duty
cycle. A continuous sample is collected from the dilution tunnel for
each test segment or test mode using sample bags. These bags are then
analyzed to determine the concentrations of HC, CO, and NOX.
1. Test Speeds
The definition of maximum test speed, where speed is the angular
velocity of an engine's crankshaft (usually expressed in revolutions
per minute, or rpm), is an important aspect of most duty cycles. Until
recently, we relied on engine manufacturers to declare reasonable rated
speeds for their engines and then used the rated speed as the maximum
test speed. However, to have a more objective measure of an engine's
maximum test speed, we have established a specific procedure for
measuring this engine parameter.\86\
---------------------------------------------------------------------------
\86\ See the final rule for commercial marine diesel engines for
a broader discussion of maximum test speed (64 FR 73300, December
29, 1999).
---------------------------------------------------------------------------
We define the maximum test speed for any engine to be the single
point on an engine's maximum-power versus speed curve that lies
farthest away from the zero-power, zero-speed point on a normalized
maximum-power versus speed plot. In other words, consider straight
lines drawn between the origin (speed = 0, load = 0) and each point on
an engine's normalized maximum-power versus speed curve. Maximum test
speed is defined at that point where the length of this line reaches
its maximum value. For constant-speed engines, maximum test speed is
the engine's rated speed.
Intermediate speed for steady-state duty cycles is defined as the
speed at which the engine generates its maximum torque value. However,
in cases where the maximum torque occurs at a speed that is less than
60 percent or greater than 75 percent of the rated speed, the
intermediate speed is often specified as either 60 or 75 percent of
rated speed, whichever is closer to the speed of maximum torque. The
maximum test speed described above is used to calculate these
percentage values relative to rated speed.
2. Maintenance
As described in Section II.C.1, we are limiting the amount of
scheduled maintenance manufacturers may prescribe for their customers
to ensure that engines continue to meet emission standards. If
manufacturers specify unreasonably frequent maintenance, there would be
little assurance that in-use engines would continue to operate at
certified emission levels. We also apply these minimum maintenance
intervals to engines the manufacturer operates for service accumulation
before testing for emissions. For example, manufacturers may not
install a new catalyst on a Large SI engine after 2,000 hours of
operation, then select that engine for the in-use testing program.
Similarly, manufacturers may not replace fuel-system components on a
recreational vehicle during the course of service accumulation for
establishing deterioration factors. We do not restrict scheduling of
routine maintenance items, such as changing engine oil and replacing
oil, fuel, or air filters. We may also allow changing spark plugs, even
though we are aware that spark plugs may affect emissions.
[[Page 68322]]
D. Other Testing Procedures
As noted in earlier sections, we are establishing some special test
procedures for field testing situations. These special procedures are
designed to apply to specific types of engines, and thus do not apply
generally to all engines covered by this rulemaking. You should read
the specific applicable section to determine if such special test
procedures apply to any specific category of engines or vehicles.
IX. Projected Impacts
This section summarizes the projected impacts of the emission
standards. The anticipated reduction in emissions is compared with the
projected cost of the program for an assessment of the cost per ton of
reducing emissions for this rule. The section includes the results of
the analysis for the Final Program. We have also analyzed the impacts
of different alternatives for each of the program areas. This analysis
of alternatives, for the most part, focused on more or less stringent
alternative standards. For recreational marine diesels, the
alternatives analyzed were applying draft European standards or
implementing our primary program two years earlier. For the Large SI
category, the alternative focused on adopting a steady-state only 2007
requirement. For off-highway motorcycles, we analyzed a more-stringent
1.0 g/km standard and a less-stringent 4.0 g/km standard for HC +
NOX control. With ATVs, the alternatives presented were a
2.0 g/km and a 1.0 g/km HC + NOX standard. For snowmobiles,
we analyzed four alternatives, ranging from only adopting one phase of
standards in 2006 to a standard that would require, on average,
reductions of 85% HC and 50% CO from baseline emissions. Additional
detailed discussion on these alternatives and the results of the
alternatives analysis are presented in Chapter 11 of the RSD.
A. Environmental Impact
To estimate nonroad engine and vehicle emission contributions, we
used the latest version of our NONROAD emissions model. This model
computes emission levels for a wide variety of nonroad engines, and
uses information on emission rates, operating data, and population to
determine annual emission levels of various pollutants. A more detailed
description of the methodology used for projecting inventories and
projections for additional years can be found in the Chapter 6 of the
Final Regulatory Support Document.
Tables IX.A-1 and IX.A-2 contain the projected emission inventories
for calendar year 2010 from the engines and vehicles subject to this
rulemaking under the base case (i.e., without the standards taking
effect) and assuming the standards take effect. Tables IX.A-3 and IX.A-
4 contain the projected emission inventories for calendar year 2020.
The percent reductions based on a comparison of estimated emission
inventories with and without the emission standards are also presented
in each of the tables.
Table IX.A-1.--2010 Projected HC and NOX Emissions Inventories
[Thousand short tons]
----------------------------------------------------------------------------------------------------------------
HC* NOX
--------------------------------------------------------------------
Category With Percent With Percent
Base case standards reduction Base case standards reduction
----------------------------------------------------------------------------------------------------------------
Large SI................................... 268 88 67 389 118 70
Snowmobiles................................ 297 250 16 3 4 (16)
ATVs....................................... 308 211 31 7 6 11
Off-highway motorcycles.................... 193 155 20 1.1 1.2 (8)
Recreational marine diesel................. 1.6 1.5 10 49 46 7
------------
Total................................ 1,066 705 34 450 174 61
----------------------------------------------------------------------------------------------------------------
* The estimate for Large SI includes both exhaust HC and evaporative HC emissions. The estimates for
snowmobiles, ATVs and Off-highway motorcycles includes both exhaust HC and permeation HC emissions. The
estimate for recreation marine diesel includes exhaust HC emissions.
Table IX.A-2.--2010 Projected CO and PM Emissions Inventories
[Thousand short tons]
----------------------------------------------------------------------------------------------------------------
CO PM
-----------------------------------------------------------------
Category With Percent With Percent
Base case standards reduction Base case standards reduction
----------------------------------------------------------------------------------------------------------------
Large SI...................................... 2,022 945 53 1.9 1.9 0
Snowmobiles................................... 775 670 14 7.0 6.7 4
ATVs.......................................... 1,042 989 5 10.8 7.4 32
Recreational marine diesel.................... 8 8 0 1.3 1.2 6
Off-highway motorcycles....................... 266 239 10 7.3 5.8 20
------------
Total................................... 4,113 2,851 31 28.3 23.0 19
----------------------------------------------------------------------------------------------------------------
Table IX.A-3.--2020 HC and NOX Projected Emissions Inventories
[Thousand short tons]
----------------------------------------------------------------------------------------------------------------
HC* NOX
-------------------------------------------------------------------
Category With Percent With Percent
Base case standards reduction Base case standards reduction
----------------------------------------------------------------------------------------------------------------
Large SI.................................... 318 34 89 472 43 91
[[Page 68323]]
Snowmobiles................................. 358 149 58 5 10 (101)
ATVs........................................ 374 53 86 8 6 25
Off-highway motorcycles..................... 232 117 50 1.3 1.5 (19)
Recreational marine diesel.................. 2.0 1.5 28 61 48 21
------------
Total................................. 1,284 355 72 547 109 80
----------------------------------------------------------------------------------------------------------------
* The estimate for Large SI includes both exhaust HC and evaporative HC emissions. The estimates for
snowmobiles, ATVs and Off-highway motorcycles includes both exhaust HC and permeation HC emissions. The
estimate for recreation marine diesel includes exhaust HC emissions.
Table IX.A-4.--2020 Projected CO and PM Emissions Inventories
[Thousand short tons]
----------------------------------------------------------------------------------------------------------------
CO PM
------------------------------------------------------- Percent
Category With Percent With reduction
Base case standards reduction Base case standards
----------------------------------------------------------------------------------------------------------------
Large SI...................................... 2,336 277 88 2.3 2.3 0
Snowmobiles................................... 950 508 46 8.4 4.9 42
ATVs.......................................... 1,250 1,085 13 13.1 1.9 86
Off-highway motorcycles....................... 321 236 26 8.7 4.4 50
Recreational Marine diesel.................... 9 9 0 1.6 1.3 18
------------
Total................................... 4,866 2,115 56 34.2 14.8 57
----------------------------------------------------------------------------------------------------------------
As described in Section I, we project there will also be
environmental benefits associated with reduced haze in many sensitive
areas.
Finally, anticipated reductions in hydrocarbon emissions correspond
with reduced emissions of the toxic air emissions referenced in Section
I.
B. Cost Estimates
In assessing the economic impact of setting emission standards, we
have made a best estimate of the necessary technologies and their
associated costs. In making our estimates we have relied on our own
technology assessment, which includes information supplied by
individual manufacturers and our own in-house testing. Estimated costs
include variable costs (for hardware and assembly time) and fixed costs
(for research and development, retooling, and certification). The
analysis also considers total operating costs, including maintenance
and fuel consumption. Cost estimates based on the projected
technologies represent an expected change in the cost of engines as
they begin to comply with new emission standards. All costs are
presented in 2001 dollars. Full details of our cost analysis can be
found in Chapter 5 of the Final Regulatory Support Document.
Cost estimates based on the current projected costs for our
estimated technology packages represent an expected incremental cost of
vehicles in the near term. For the longer term, we have identified
factors that will cause cost impacts to decrease over time. First, we
project that manufacturers will generally recover their fixed costs
over a five-year period, so these costs disappear from the analysis
after the fifth year of production. Second, the analysis incorporates
the expectation that manufacturers and suppliers will apply ongoing
research and manufacturing innovation to making emission controls more
effective and less costly over time. Research in the costs of
manufacturing unrelated to emissions control technologies has
consistently shown that as manufacturers gain experience in production
and use, they are able to apply innovations to simplify machining and
assembly operations, use lower cost materials, and reduce the number or
complexity of component parts (see the Final Regulatory Support
Document for additional information).\87\ The cost analysis assumes
this learning effect applies equally well to the adoption of the
technologies associated with this rule by decreasing estimated variable
costs by 20 percent starting in the third year of production and an
additional 20 percent starting in the sixth year of production.
---------------------------------------------------------------------------
\87\ For further information on learning curves, see Chapter 5
of the Economic Impact, from Regulatory Impact Analysis-Control if
Air Pollution from New Motor Vehicles: Tier 2 Motor Vehicle Emission
Standards and Gasoline Sulfur Control Requirements, EPA420-R-99-023,
December 1999. A copy of this document is included in Air Docket A-
2000-01, at Document No. II-A-83. The interested reader should also
refer to previous final rules for Tier 2 highway vehicles (65 FR
6698, February 10, 2000), marine diesel engines (64 FR 73300,
December 29, 1999), nonroad diesel engines (63 FR 56968, October 23,
1998), and highway diesel engines (62 FR 54694, October 21, 1997).
---------------------------------------------------------------------------
Table IX.B-1 summarizes the projected near-term per unit average
costs to meet the new emission standards. These estimates are based on
the manufacturing cost rather than predicting price increase; the costs
nevertheless take into account anticipated mark-ups to present retail-
price equivalent figures. Long-term impacts on engine costs are
expected to decrease as manufacturers fully amortize their fixed costs
and learn to optimize their designs and production processes to meet
the standards more efficiently. The tables also show our projections of
reduced operating costs for some engines (calculated on a net present
value basis), which generally results from substantial reductions in
fuel consumption.
[[Page 68324]]
Table IX.B-1.--Estimated Average Cost Impacts of Emission Standards
------------------------------------------------------------------------
Increased Lifetime
production operating
Standards Dates cost per costs per
vehicle* vehicle (NPV)
------------------------------------------------------------------------
Large SI exhaust............ 2004 $611 $-3,981
Large SI exhaust............ 2007 55 0
Large SI evaporative........ 2007 13 -56
Snowmobile exhaust (Phase 1) 2006 73 -57
Snowmobile exhaust (Phase 2) 2010 131 -286
Snowmobile exhaust (Phase 3) 2012 89 -191
Snowmobile permeation....... 2008 7 -11
ATV exhaust................. 2006 84 -24
ATV permeation.............. 2008 3 -6
Off-highway motorcycle 2006 155 -48
exhaust....................
Off-highway motorcycle 2008 3 -5
peermeation................
Recreational................ 2006 346 0
------------------------------------------------------------------------
* These estimates are for near-term costs. The estimated long-term costs
decrease by about 35 percent. Costs presented for the Large SI and
snowmobile second-phase standards are incremental to the first-phase
standards. Costs for Phase 3 are incremental to Phase 2. These costs
numbers may not necessarily reflect actual price increases as
manufacturer production costs, perceived product enhancements, and
other market impacts will affect actual prices to consumers.
We estimate that the anticipated increase in the near-term cost of
producing new Large SI engines for the 2004 standards is estimated to
range from $550 to $800, depending on fuel type, with a composite
estimated cost of $605. This cost is attributed to upgrading engines to
operate with closed-loop fuel systems and three-way catalysts. These
technologies also improve the overall performance of these engines,
including improvements to fuel economy that result in reduced operating
costs that fully offset the additional hardware cost. We further
estimate additional costs of $50 for the 2007 standards, which
primarily involve additional development time to optimize engines using
the same closed-loop systems with three-way catalysts. While these
costs are a small percentage of the cost of industrial equipment, we
are aware that this may not be insignificant in this very competitive
market. Given the compelling advantages of improved performance and
reduced operating expenses, however, we believe manufacturers will
generally be able to recover their costs over time.\88\
---------------------------------------------------------------------------
\88\ Chapter 5 of the Final Regulatory Support Document
describes why we believe market forces haven't already led
manufacturers to add fuel-saving technologies to their products.
---------------------------------------------------------------------------
Projected average near-term costs for ATVs and off-highway
motorcycles are $84 and $155 per unit, respectively. Standards are
based on the emission-control capability of engines four-stroke
engines.\89\ Those models that convert from two-stroke to four-stroke
technology will see substantial fuel savings in addition to greatly
reduced emissions. With an averaging program that allows manufacturers
to apply varying degrees of technology to different models, we believe
they will be able to tailor emission controls in a way that reflects
the performance needs for their products. Fuel savings associated with
replacing two-stroke engines with four-stroke engines partially offsets
the additional cost of producing these vehicles.
---------------------------------------------------------------------------
\89\ The program contains an optional set of standards for off-
highway motorcycles which could result in the use of direct
injection two-stroke technology in some high-performance
applications. Chapter 11.3 provides a cost analysis for this option.
The costs are projected to be somewhat higher for this option due to
the application of technology to high-performance competition
models.
---------------------------------------------------------------------------
We expect that the near-term cost of the 2006 snowmobile standards
will average $73 per snowmobile. These costs are based on a mix of
technologies including a small increase in the use of four-stroke and
direct injection technology. For other engines we expect manufacturers
to lean out the air-fuel mixture, improve carburetion for better fuel
control and less production variation, and modify the engine to
withstand higher temperatures and potential misfire episodes attributed
to enleanment. We expect that the 2010 and 2012 standards will be met
through inceasing the application of direct injection two-stroke
technology and four-stroke engines on a significant portion of the
fleet. We project that the near-term incremental cost of the Phase 2
standards will average $131 per snowmobile and Phase 3 will be $89,
although we believe these costs will be fully offset by fuel savings.
Recreational marine diesel engines are expected to see increased
costs averaging under $400 per engine in the near-term. We expect
manufacturers to meet emission standards by improving fuel injection
systems and making general design changes to the geometries,
configurations, and calibrations of their engines. These figures are
somewhat lower than we have projected for the comparable commercial
marine engines, since the recreational models generally already have
some of the emission-control technologies needed to meet the emission
standards.
The above analysis presents unit cost estimates for each type of
engine or vehicle. These costs represent the total set of costs the
engine or vehicle manufacturers will bear to comply with emission
standards. For those categories with engine-based standards, we do not
anticipate significant new costs for equipment manufacturers installing
certified engines. Operating costs are also taken into account, but
where there is an effect, we project these impacts to involve only cost
savings for operators. With current and projected estimates of engine
and equipment sales, we translate these costs into projected direct
costs to the nation for the new emission standards in any year. A
summary of the annualized costs to manufacturers by equipment type is
presented in Table IX.B-2. (The annualized costs are determined over
the first twenty years that the standards will be in effect. Because
the standards take effect in different years for the various categories
of equipment covered by this rule, the aggregate annualized cost is
calculated over a slightly longer period of time encompassing the first
twenty years of each of the standards. For this reason, the aggregate
annualized cost is not the sum of the individual annualized costs.) The
annual cost savings due to reduced operating expenses start slowly,
then increase as greater numbers of
[[Page 68325]]
compliant engines enter the fleet. Table IX.B-2 also presents a summary
of the annualized reduction in operating costs. Overall, based on
currently available information, we project an annualized net savings
to the economy of approximately $200 million per year.
Table IX.B-2--Estimated Annual Cost to Manufacturers and Annual Savings
from Reduced Operating Costs of Emission Standards
------------------------------------------------------------------------
Annualized
Annualized savings from
cost to reduced
Engine type manufacturers operating
(millions/ costs
year) (millions/
year)
------------------------------------------------------------------------
Large SI................................ $84 $324
Snowmobiles............................. 36 47
ATVs.................................... 61 31
Off-highway motorcycles................. 25 14
Marine Diesel........................... 7 0
Aggregate *............................. 192 410
------------------------------------------------------------------------
* Because the standards take effect in different years for the various
categories of equipment, the aggregate annualized cost is calculated
over a slightly longer period of time. For this reason, the aggregate
annualized cost is not the sum of the individual annualized costs.
C. Cost Per Ton of Emissions Reduced
We calculated the cost per ton of emission reductions for the
emission standards. For snowmobiles, this calculation is on the basis
of HC and CO emissions. For all other engines, we attributed the entire
cost of the program to the control of ozone precursor emissions (HC or
NOX or both).
Table IX.C-1 presents the near-term discounted cost-per-ton
estimates for the various engines covered by the rule. (The aggregate
cost-per-ton estimates are over the first 20 years of emission
standards.) Reduced operating costs more than offset the increased cost
of producing the cleaner engines for Phase 1 Large SI, and Phase 2 and
Phase 3 snowmobile engines. The cost to society and the associated
cost-per-ton figures for these engines, and the aggregate values for
all engines covered by this rule, therefore show a net savings
resulting from the emission standards. The table presents these as $0
per ton, rather than calculating a negative value that has no clear
meaning.
Table IX.C-1.--Estimated Cost-per-Ton of Emission Standards
----------------------------------------------------------------------------------------------------------------
Discounted cost per Discounted cost per
Discounted ton of HC+NOX ton of CO
reductions --------------------------------------------
Standards Dates per vehicle Without Without With
(short tons) fuel With fuel fuel fuel
* savings savings savings savings
----------------------------------------------------------------------------------------------------------------
Large SI exhaust (Composite of all fuels).. 2004 3.07 $240 $0 -- --
Large SI exhaust (Composite of all fuels).. 2007 0.80 80 80 --
Large SI evaporative....................... 2007 0.13 80 0 --
Snowmobile exhaust......................... 2006 HC: 0.40 90 20 $40 $10
........ CO:.......... .......... .......... .......
Snowmobile exhaust......................... 2010 HC: 0.1,370 0 -- --
Snowmobile exhaust......................... 2012 CO: 0.25-- -- 360 0
Snowmobile permeation...................... 2008 0.03 210 0 -- --
ATV exhaust................................ 2006 0.21 400 290 -- --
ATV permeation............................. 2008 0.02 180 0 -- --
Off-highway motorcycle exhaust............. 2006 0.38 410 280 -- --
Off-highway motorcycle permeation.......... 2008 0.01 230 0 -- --
Recreational marine diesel................. 2006 0.44 670 670 -- --
Aggregate.................................. -- -- 240 0 80 0
----------------------------------------------------------------------------------------------------------------
* HC reductions for evaporative and permeation, and HC+NOX reductions for exhaust (except snowmobiles where CO
reductions are also presented).
D. Economic Impact Analysis
We performed an analysis to estimate the economic impacts of this
final rule on producers and consumers of recreational marine diesel
vessels (specifically, diesel inboard cruisers), forklifts,
snowmobiles, ATVs, off-highway motorcycles, and society as a whole.
This economic impact analysis focuses on market-level changes in price,
quantity, and economic welfare (social gains or costs) associated with
the regulation. A description of the methodology used can be found in
Chapter 9 of the Final Regulatory Support Document prepared for this
rulemaking.
We did not perform an economic impact analysis for categories of
Large SI nonroad engines other than forklifts, even though those other
Large SI engines are also subject to the standards contained in this
final rule. As explained in more detail in Chapter 9 of the Final
Regulatory Support Document, this was due to the large number of
different types of equipment that use Large SI engines and data
availability constraints for those market segments. For the sake of
completeness, the following analysis reports separate estimates for
Large SI engines other than forklifts. Engineering costs are assumed
[[Page 68326]]
to be equal to economic costs for those engines. This approach slightly
overestimates the social costs associated with the relevant standards.
Based on the estimated regulatory costs associated with this rule
and the predicted changes in prices and quantity produced in the
affected industries, the total estimated annual social gains of the
rule in the year 2030 is projected to be $553.5 million (in 2000 and
2001 dollars). The net present value of the social gains for the 2002
to 2030 time frame is equal to $4.9 billion, using a 3% discount rate.
This value would be $2.4 billion with a 7% discount rate. The social
gains are equal to the fuel savings minus the combined loss in consumer
and producer surplus (see Table IX.D-1), taking into account producers'
and consumers' changes in behavior resulting from the costs associated
with the rule.\90\ Social gains do not account for the social benefits
(the monetized health and environmental effects of the rule).
---------------------------------------------------------------------------
\90\ Consumer and producer surplus losses are measures of the
economic welfare loss consumers and producers, respectively are
likely to experience as a result of the regulations. Combined these
losses represent an estimate of the economic or social costs of the
rule. Note that for the Large SI and recreational vehicle rules,
fuel efficiency gains must be netted from surplus losses to estimate
the social costs or social gains (in cases where fuel efficiency
gains exceed surplus losses) attributable to the rules.
Table IX.D-1.--Surplus Losses, Fuel Efficiency Gains, and Social Gains/Costs in 2030 a
----------------------------------------------------------------------------------------------------------------
Social gains/
Surplus losses Fuel efficiency costs in 2030
Vehicle category in 2030 ($ gains in 2030 b ($
millions) ($ millions) millions)
----------------------------------------------------------------------------------------------------------------
Recreational marine diesel vessels............................. $6.6 $0 ($6.6)
Forklifts...................................................... 47.8 420.1 372.3
Other Large SI................................................. c 48.1 138.4 90.3
Snowmobiles.................................................... 41.9 135.0 93.1
ATVs........................................................... 47.2 51.4 4.2
Off-highway motorcycles........................................ 25.0 25.2 0.2
All vehicles total............................................. 216.6 770.1 553.5
NPV of all vehicles total d.................................... 3,231.4 8,130.3 4,898.9
NPV of all vehicles total e.................................... 1,889.5 4,282.3 2,392.8
----------------------------------------------------------------------------------------------------------------
a Figures are in 2000 and 2001 dollars.
b Figures in this column exclude estimated social benefits. Numbers in parentheses denote social costs.
c Figure is engineering costs; see text for explanation.
d Net Present Value is calculated over the 2002 to 2030 time frame using a 3 percent discount rate.
e Net Present Value is calculated over the 2002 to 2030 time frame using a 7 percent discount rate.
For most of the engine categories contained in this rule, we expect
there will be a fuel savings as manufacturers redesign their engines to
comply with emission standards. For ATVs and off-highway motorcycles,
the fuel savings will be realized as manufacturers switch from two-
stroke to four-stroke technologies. For snowmobiles, the fuel savings
will be realized as manufacturers switch some of their engines to more
fuel efficient two-stroke technologies and some of their engines to
four-stroke technologies. For Large SI engines, the fuel savings will
be realized as manufacturers adopt more sophisticated and more
efficient fuel systems; this is true for all fuels used by Large SI
engines. Overall, we project the fuel savings associated with the
anticipated changes in technology to be about 800 million gallons per
year once the program is fully phased in. These savings are factored
into the calculated costs and costs per ton of reduced emissions, as
described above.
E. Do the Benefits Outweigh the Costs of the Standards?
While EPA uses relative cost-effectiveness as the primary manner to
take costs into consideration, further insight regarding the standards
can be provided by benefit-cost analysis. The purpose of this section
is to summarize the methods we used and results we obtained in
conducting an analysis of the economic benefits of the changes in
emissions from engines covered by this rule, and to compare these
economic benefits with the estimated economic costs of the rule. In
summary, the results of our analysis indicate that the economic
benefits of the final standards will exceed the costs of meeting the
standards. The annual estimated benefits we were able to quantify were
approximately $10 billion in 2030.
1. What Was Our Overall Approach to the Benefit-Cost Analysis?
The basic question we sought to answer in the benefit-cost analysis
was, ``What are the net yearly economic benefits to society of the
reduction in mobile source emissions likely to be achieved by this
final rulemaking?'' In designing an analysis to address this question,
we selected a future year for analysis (2030) that is representative of
full-implementation of the program (i.e., when the Large SI and
recreational vehicle fleet is composed of virtually only compliant
vehicles).
To quantify benefits, we evaluated PM-related health effects
(including directly emitted PM and NOX contribution to
particulate nitrate) using a benefits transfer technique. Although we
expect economic benefits to exist, we were unable to quantify or to
value specific changes in visibility, ozone, CO or air toxics because
we did not perform additional air quality modeling.
To evaluate the PM-related health effects, we adopted a benefits
transfer technique that relies on the extensive particulate matter air
quality and benefits modeling conducted for the highway Heavy Duty
Engine/Diesel Fuel final rule.\91\ That RIA used an analytical
structure and sequence similar to that used in the ``section 812
studies'' to estimate the total benefits and costs of the full Clean
Air Act.\92\ In the HD
[[Page 68327]]
Engine/Diesel Fuel analysis, we used many of the same models and
assumptions used in the section 812 studies as well as other Regulatory
Impact Analyses (RIAs) prepared by the Office of Air and Radiation. By
adopting the major design elements, models, and assumptions developed
for the section 812 studies and other RIAs, we have largely relied on
methods which have already received extensive review by the independent
Science Advisory Board (SAB), by the public, and by other federal
agencies. Although the underlying method has experienced significant
review, the transfer of values from an existing primary benefits
analysis to estimate the benefits of a new program has not had this
type of review and the transfer technique introduces additional
uncertainties.
---------------------------------------------------------------------------
\91\ Regulatory Impact Analysis: Heavy-Duty Engine and Vehicle
Standards and Highway Diesel Fuel Sulfur Control Requirements,
document EPA420-R-00-026, December 2000. Docket No. A-2000-01,
Document No. II-A-13. This document is also available at http://
www.epa.gov/otaq/diesel.htm#documents. The transfer technique is
described in a memorandum, Dr. Bryan Hubbell, Senior Economist,
Estimated Nox, Sox, and PM Emissions Health Damages for Heavy Duty
Vehicle Emissions, April 22, 2002. A copy of this letter can be
found in Docket A-2000-01, Document IV-A-146.
\92\ The section 812 studies include: (1) U.S. EPA, Report to
Congress: The Benefits and Costs of the Clean Air Act, 1970 to 1990,
October 1997 (also known as the ``Section 812 Retrospective
Report''); and (2) the first in the ongoing series of prospective
studies estimating the total costs and benefits of the Clean Air Act
(see EPA report number: EPA-410-R-99-001, November 1999). See Docket
A-99-06, Document II-A-21.
---------------------------------------------------------------------------
2. What Are the Significant Limitations of the Benefit-Cost Analysis?
Every benefit-cost analysis examining the potential effects of a
change in environmental protection requirements is limited to some
extent by data gaps, limitations in model capabilities (such as
geographic coverage), and uncertainties in the underlying scientific
and economic studies used to configure the benefit and cost models.
Deficiencies in the scientific literature often result in the inability
to estimate quantitative changes in health and environmental effects,
such as potential increases in premature mortality associated with
increased exposure to carbon monoxide. Deficiencies in the economics
literature often result in the inability to assign economic values even
to those health and environmental outcomes which can be quantified.
While these general uncertainties in the underlying scientific and
economics literatures, which can cause the valuations to be higher or
lower, are discussed in detail in the Final Regulatory Support Document
and its supporting documents and references, the key uncertainties
which have a bearing on the results of the benefit-cost analysis of
this final rule include the following:
. The exclusion of potentially significant benefit categories
(such as health and ecological benefits of reduction in hazardous air
pollutants emissions and ozone; improvements in visibility);
. Errors in measurement and projection for variables such as
population growth;
. Uncertainties in the estimation of future year emissions
inventories and air quality;
. Uncertainties associated with the transfer of the results
of the HD Engine/Diesel Fuel analysis to this program, especially
regarding the assumption of similarity in geographic distribution
between emissions and human populations and years of analysis;\93\
---------------------------------------------------------------------------
\93\ In the original HD Engine/Diesel Fuel analysis, we modeled
air quality and benefits in 2030. There are sufficient non-
linearities and interactions among pollutants in the atmospheric
chemistry that introduce additional uncertainties in the
quantitative estimate of the benefits in years that were not fully
modeled in the original analysis.
---------------------------------------------------------------------------
. Variability in the estimated relationships of health and
welfare effects to changes in pollutant concentrations;
. Uncertainties in exposure estimation;
. Uncertainties in applying willingness to pay estimates from
National Park and Forest visitors to U.S. recreational participants and
uncertainties in average number of activity days per year; and
. Uncertainties associated with the effect of potential
future actions to limit emissions.
Despite these uncertainties, we believe the benefit-cost analysis
provides a reasonable indication of the expected economic benefits of
the final rulemaking in future years under a set of assumptions.
One key area of uncertainty is the value of a statistical life
(VSL) for reductions in mortality risk. The adoption of a value for the
projected reduction in the risk of premature mortality is the subject
of continuing discussion within the economic and public policy analysis
community. In accordance with the independent Science Advisory Board
advice,\94\ we use the value of a statistical life (VSL) for risk
reductions in mortality in our primary estimate. Alternative
calculations of adjustment for age and other factors are presented in
the RIA for the HD Engine/Diesel Fuel rule and in the RSD for this
rule. The presentation of the other alternative calculations for
certain endpoints seeks to demonstrate how much the overall benefit
estimate might vary based on the value EPA has given to a parameter
(which has uncertainty associated with it) underlying the estimates for
human health and environmental effect incidence and the economic
valuation of those effects. These alternative calculations represent
conditions that might occur; however, EPA has selected the best values
supported by current scientific literature for use in the primary
estimate. The primary estimate is the source for our benefits transfer
technique.
---------------------------------------------------------------------------
\94\ SAB advised that the EPA ``continue to use a wage-risk-
based VSL as its primary estimate, including appropriate sensitivity
analyses to reflect the uncertainty of these estimates,'' and that
``the only risk characteristic for which adjustments to the VSL can
be made is the timing of the risk'' (EPA-SAB-EEAC-00-013; a copy of
this document can be found in Docket A-99-06, Document No. IV-A-19).
In developing our primary estimate of the benefits of premature
mortality reductions, we have appropriately discounted over the lag
period between exposure and premature mortality. However, an
empirical basis that meets the SAB's standards of reliability for
adjusting the current $6 million VSL for many of these factors does
not yet exist. A discussion of these factors is contained in the RIA
and supporting documents. EPA recognizes the need for additional
research by the scientific community to develop additional empirical
support for adjustments to VSL for the factors mentioned above.
---------------------------------------------------------------------------
Even with our efforts to fully disclose the uncertainty in our
estimate, our uncertainty presentation method does not provide a
definitive or complete picture of the true range of monetized benefits
estimates. The set of alternative calculations is only representative
of those benefits that we were able to quantify and monetize.
3. What Are the benefits In the Years Leading Up to 2030?
The final rule has various cost and emission related components, as
described earlier in this section. These components would begin at
various times and in some cases would phase in over time. This means
that during the early years of the program there would not be a
consistent match between cost and benefits, especially where the full
vehicle cost would be incurred at the time of vehicle purchase, while
the fuel savings along with the emission reductions and benefits
resulting from all these costs would occur throughout the lifetime of
the vehicle. Because of this inconsistency and our desire to more
appropriately match the costs and emission reductions of our program,
our analysis uses a future year (2030) when the fleet is nearly fully
turned over.
In the years before 2030, the benefits from the final rule will be
less than those estimated here, because the compliant vehicle fleet
will not be fully phased in, and the overall U.S. population would be
smaller. Annualized costs, on the other hand, reach nearly their full
value within a few years of program initiation (once all phase-ins are
completed). Thus, a benefit-cost ratio computed for the earlier years
of the program would be expected to be lower than a ratio based on our
2030 analysis when the fleet has fully turned over. The stream of costs
and the limited set of quantified benefits over time are presented in
the Final
[[Page 68328]]
Regulatory Support Document. On the other hand, since the estimated
benefits are more than 40 times the costs (excluding fuel savings) in
2030, the emission reduction and cost trends suggest that it is likely
that annual benefits would exceed costs from a time early in the life
of the program.
4. What Were the Results of the Benefit-Cost Analysis?
The benefit-cost analysis for the final rule reflects a single year
picture of the yearly benefits and costs expected to be realized once
the standards have been fully implemented and non-compliant vehicles
have all been retired.
Table IX.E-1 presents EPA's primary estimate of the benefits of the
rule, both the estimated reductions in incidences and the estimated
economic value of those incidence reductions. In interpreting the
results, it is important to keep in mind the limited set of effects we
are able to monetize. Specifically, the table lists the avoided PM-
related incidences of health effects and the estimated economic value
of those avoided incidences.\95\ We present estimates for the
reductions for the Large SI category only. As the table indicates, we
estimate that the final rule will reduce premature mortality associated
with fine PM by around 1,000 incidences per year, produce about 600
fewer cases of chronic bronchitis, and result in significant reductions
in minor restricted activity days (with an estimated 1 million fewer
cases).\96\
---------------------------------------------------------------------------
\95\ Based upon recent preliminary findings by the Health
Effects Institute, the concentration-response functions used to
estimate reductions in hospital admissions may over- or
underestimate the true concentration-response relationship. See
Letter from Dan Greenberg, President, Health Effects Institute, May
30, 2002, attached to letter from Dr. Hopke, dated August 8, 2002.
Docket A-2000-01, Document IV-A-145.
\96\ Our estimate also incorporates significant reductions in
27,000 fewer cases of lower respiratory symptoms, and 26,600 fewer
cases of upper respiratory symptoms in asthmatic children each year.
In addition, we estimate that this final rule will reduce 23,400
incidents of asthma attacks each year in asthmatics of all ages from
reduced exposure to particles. Additional incidents would be avoided
from reduced ozone exposures. Asthma is the most prevalent chronic
disease among children and currently affects over seven percent of
children under 18 years of age.
Table IX.E-1.--EPA Primary Estimate of the Annual Quantified and Monetized Benefits Associated With Improved PM
Air Quality Resulting From the Large SI/Recreational Vehicle Rule in 2030 a
----------------------------------------------------------------------------------------------------------------
Monetary benefits a,d (millions
PM-related endpoint Avoided incidence a,c (cases/year) 2002 $)
----------------------------------------------------------------------------------------------------------------
Premature mortality a,b (adults, ages 1,000............................... $7,510
30 and over).
Chronic bronchitis................... 640................................. $280
Hospital Admissions from Respiratory 300................................. <$10
Causes g.
Hospital Admissions from 300................................. <$10
Cardiovascular Causes g.
Emergency Room Visits for Asthma..... 300................................. <$1
Acute bronchitis (children, ages 8- 2,200............................... <$1
12).
Upper respiratory symptoms (asthmatic 20,600.............................. <$1
children, ages 9-11).
Lower respiratory symptoms (children, 23,700.............................. <$1
ages 7-14).
Asthma attacks (asthmatics, all ages) 20,600.............................. <$1
a.
Work loss days (adults, ages 18-65).. 181,300............................. $20
Minor restricted activity days 944,400............................. $50
(adults, ages 18-65) (adjusted to
exclude asthma attacks) a.
Other health effects e............... U1+U2+U3+U4......................... B1+B2+B3+B4
---------------------------------------
Monetized Total f................ .................................... $7,880 + B
----------------------------------------------------------------------------------------------------------------
a Ozone-related benefits are not included, thus underestimating national benefits. Relative to PM related
benefits, ozone benefits have typically accounted for only a small portion of total benefits. However, ozone
reductions can have a significant impact on asthma attacks in asthma sufferers, as well as contributing to
reductions in the overall number of minor restricted activity days.
b The value we are transferring assumes that some of the incidences of premature mortality related to PM
exposures occur in a distributed fashion over the five years following exposure, and it embeds an annual three
percent discount rate to the value of premature mortality occurring in years after our analysis year.
c Incidences are rounded to the nearest 100.
d Dollar values are rounded to the nearest 10 million. Monetary benefits account for growth in real GDP per
capita through 2030.
e The Ui are the incidences and the Bi are the values for the unquantified category i. A detailed listing of
unquantified PM, ozone, CO, and HC related health and welfare effects is provided in Table IX-E.2. Many of the
HC emitted from these vehicles are also hazardous air pollutants listed in the Clean Air Act.
f B is equal to the sum of all unmonetized categories, i.e., Ba+B1+B2+ * * * +Bn.
g Based upon recent preliminary findings by the Health Effects Institute, the concentration-response functions
used to estimate reductions in hospital admissions may over- or under-estimate the true concentration-response
relationship.
Total monetized benefits are driven primarily by the reduction in
premature fatalities each year, which account for over 80 percent of
total benefits.
This table also indicates with a ``B'' those additional health and
environmental benefits which could not be expressed in quantitative
incidence and/or economic value terms. A full listing of the benefit
categories that could not be quantified or monetized in our estimate
are provided in Table IX.E-2. The final rule may also provide some
visibility improvements in Class I areas and near where people live,
work, and recreate. A full appreciation of the overall economic
consequences of the final standards requires consideration of all
benefits and costs expected to result from the new standards, not just
those benefits and costs which could be expressed here in dollar terms.
Table IX.E-2.--Additional, Non-monetized Benefits of the Large SI/
Recreational Vehicle Standards
------------------------------------------------------------------------
Pollutant Unquantified effects
------------------------------------------------------------------------
Ozone Health........................... Premature mortality.a
Increased airway responsiveness
to stimuli.
Inflammation in the lung.
Chronic respiratory damage.
Premature aging of the lungs.
[[Page 68329]]
Acute inflammation and
respiratory cell damage.
Increased susceptibility to
respiratory infection.
Non-asthma respiratory
emergency room visits.
Increased school absence rates
Ozone Welfare.......................... Decreased yields for commercial
forests (for example, Western
US).
Decreased yields for fruits and
vegetables.
Decreased yields for non-
commercial crops.
Damage to urban ornamental
plants.
Impacts on recreational demand
from damaged forest
aesthetics.
Damage to ecosystem functions
PM Health.............................. Infant mortality.
Low birth weight.
Changes in pulmonary function.
Chronic respiratory diseases
other than chronic bronchitis.
Cardiac endpoints.
Morphological changes.
Altered host defense
mechanisms.
Cancer.
Non-asthma respiratory
emergency room visits
PM Welfare............................. Visibility in Class I areas.
Residential and recreational
visibility in non-Class I
areas.
Soiling and materials damage.
Damage to ecosystem functions
Nitrogen and Sulfate Deposition Welfare Impacts of acidic sulfate and
nitrate deposition on
commercial forests
Impacts of acidic deposition to
commercial freshwater fishing.
Impacts of acidic deposition to
recreation in terrestrial
ecosystems.
Reduced existence values for
currently healthy ecosystems.
Impacts of nitrogen deposition
on commercial fishing,
agriculture, and forests.
Impacts of nitrogen deposition
on recreation in estuarine
ecosystems.
Damage to ecosystem functions
CO Health.............................. Premature mortalitya.
Behavioral effects.
Hospital admissions--
respiratory, cardiovascular,
and other.
Other cardiovascular effects
Developmental effects.
Decreased time to onset of
angina.
Non-asthma respiratory ER
visits
HC Health b............................ Cancer (benzene, 1,3-butadiene,
formaldehyde, acetaldehyde).
Anemia (benzene).
Disruption of production of
blood components (benzene).
Reduction in the number of
blood platelets (benzene).
Excessive bone marrow formation
(benzene).
Depression of lymphocyte counts
(benzene)
Reproductive and developmental
effects (1,3-butadiene).
Irritation of eyes and mucus
membranes (formaldehyde).
Respiratory irritation
(formaldehyde).
Asthma attacks in asthmatics
(formaldehyde).
Asthma-like symptoms in non-
asthmatics (formaldehyde).
Irritation of the eyes, skin,
and respiratory tract
(acetaldehyde).
Upper respiratory tract
irritation and congestion
(acrolein)
HC Welfare............................. Direct toxic effects to
animals.
Bioaccumulation in the food
chain.
Damage to ecosystem function
------------------------------------------------------------------------
a Premature mortality associated with ozone and carbon monoxide is not
separately included in this analysis. In this analysis, we assume that
the ACS/Krewski, et al. C-R function for premature mortality captures
both PM mortality benefits and any mortality benefits associated with
other air pollutants. A copy of Krewski, et al., can be found in
Docket A-99-06, Document No. IV-G-75.
b Many of the key hydrocarbons related to this rule are also hazardous
air pollutants listed in the Clean Air Act.
In summary, EPA's primary estimate of the benefits of the final
rule is approximately $7.8 billion in 2030. This estimate accounts for
growth in real gross domestic product (GDP) per capita between the
present and 2030.
The estimated social cost (measured as changes in consumer and
producer surplus) in 2030 to implement the final rule from Table IX.D-1
above is $217 million (2001$). The net social gain, considering fuel
efficiency, is $554 million. The monetized benefits are approximately
$7.8 billion, and EPA believes there is considerable value to the
public of the benefits it could not monetize. The net benefit that can
be monetized is $8.4 billion. Therefore, implementation of the final
rule is expected to provide society with a net gain in social welfare
based on economic efficiency criteria. Table IX.E-3 summarizes the
costs, benefits, and net benefits.
The net present value of the future benefits have been calculated
using a 3% discount rate over the 2002 to 2030 time frame. The net
present value of the social gains is $4,899 million and the net present
value of the total annual benefits is $77,177 million + B.
Consequently, the net present value of the monetized net benefits of
this program is $82,076 million. If a discount rate of 7% is used, the
values above change to $2,393 million for social gains and $40,070
million + B for total benefits, giving a total of $42,463 million.
Table IX.E-3.--2030 Annual Monetized Costs, Benefits, and Net Benefits
for the Final Rule
------------------------------------------------------------------------
Millions of 2001 $ a
------------------------------------------------------------------------
Social Gains f............................. $550
[[Page 68330]]
Monetized PM-related benefits b,c.......... $7,880 + BPM
Monetized Ozone-related benefits b,d....... Not monetized (BOzone)
HC-related benefits........................ Not monetized (BHC)
CO-related benefits........................ Not monetized (BCO)
Total annual benefits...................... $7,880 +BPM + BOzone + BHC
+ BCO
Monetized net benefits e................... $8,430 + B
------------------------------------------------------------------------
a For this section, all costs and benefits are rounded to the nearest 10
million. Thus, figures presented in this chapter may not exactly equal
benefit and cost numbers presented in earlier sections of the chapter.
b Not all possible benefits or disbenefits are quantified and monetized
in this analysis. Potential benefit categories that have not been
quantified and monetized are listed in Table IX-E.2. Unmonetized PM-
and ozone-related benefits are indicated by BPM. and BOzone,
respectively.
c Based upon recent preliminary findings by the Health Effects
Institute, the concentration-response functions used to estimate
reductions in hospital admissions may over- or under-estimate the true
concentration-response relationship.
d There are substantial uncertainties associated with the benefit
estimates presented here, as compared to other EPA analyses that are
supported by specific modeling. This analysis used a benefits transfer
technique described in the RSD.
e B is equal to the sum of all unmonetized benefits, including those
associated with PM, ozone, CO, and HC.
f The social gains are equal to the fuel savings minus the combined loss
in consumer and producer surplus.
X. Public Participation
A wide variety of interested parties participated in the rulemaking
process that culminates with this final rule. This process provided
several opportunities for public comment over a period of more than two
years. An Advance Notice of Proposed Rulemaking (65 FR 76797, December
7, 2000) announced our intent to address emissions from these engines.
Comments received during this period were considered in the development
of the proposal and are discussed in that document. These comments
included information received from small businesses as a part of the
inter-agency Small Business Advocacy Review Panel process which was
completed before we published the proposal and is described below under
the discussion of the Regulatory Flexibility Act. The formal comment
period and public hearing associated with the proposal provided another
opportunity for public input. We have also met with a variety of
stakeholders at various points in the process, including state and
environmental organizations, engine manufacturers, and equipment
manufacturers.
We have prepared a detailed Summary and Analysis of Comments
document, which describes the comments we received on the proposal and
our response to each of these comments. The Summary and Analysis of
Comments is available in the docket for this rule and on the Office of
Transportation and Air Quality internet home page at http://
www.epa.gov/otaq/.
XI. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
Under Executive Order 12866 (58 FR 51735, October 4, 1993), the
Agency must determine whether the regulatory action is ``significant''
and therefore subject to review by the Office of Management and Budget
(OMB) and the requirements of this Executive Order. The Executive Order
defines a ``significant regulatory action'' as any regulatory action
that is likely to result in a rule that may:
. Have an annual effect on the economy of $100 million or
more or adversely affect in a material way the economy, a sector of the
economy, productivity, competition, jobs, the environment, public
health or safety, or State, Local, or Tribal governments or
communities;
. Create a serious inconsistency or otherwise interfere with
an action taken or planned by another agency;
. Materially alter the budgetary impact of entitlements,
grants, user fees, or loan programs, or the rights and obligations of
recipients thereof; or
. Raise novel legal or policy issues arising out of legal
mandates, the President's priorities, or the principles set forth in
the Executive Order.
A Final Regulatory Support Document has been prepared and is
available in the docket for this rulemaking and at the internet address
listed under ADDRESSES above. This action was submitted to the Office
of Management and Budget for review under Executive Order 12866. Annual
initial costs of this rulemaking are estimated to be over $100 million
per year but this is offset by operating cost savings of over $400
million dollars per year. Even so, this rule is considered economically
significant. Written comments from OMB and responses from EPA to OMB
comments are in the public docket for this rulemaking.
B. Paperwork Reduction Act
The information collection requirements (ICR) in this rule will be
submitted for approval to the Office of Management and Budget (OMB)
under the Paperwork Reduction Act, 44 U.S.C. 3501 et seq.
The Agency may not conduct or sponsor an information collection,
and a person is not required to respond to a request for information,
unless the information collection request displays a currently valid
OMB control number. The OMB control numbers for EPA's regulations are
listed in 40 CFR part 9 and 48 CFR chapter 15.
The reporting requirements in this final rule do not apply until
the Office of Management has approved them. We will publish a document
in the Federal Register announcing that the information-collection
requirements are approved.
C. Regulatory Flexibility Act (RFA), as Amended by the Small Business
Regulatory Enforcement Fairness Act of 1996 (SBREFA), 5 U.S.C. 601 et
seq.
EPA has determined that it is not necessary to prepare a regulatory
flexibility analysis in connection with this final rule. EPA has also
determined that this rule will not have a significant economic impact
on a substantial number of small entities.
For purposes of assessing the impacts of this final rule on small
entities, a small entity is defined as: (1) A small business that meet
the definition for business based on SBA size standards; (2) a small
governmental jurisdiction that is a government of a city, county, town,
school district or special district with a population of less than
50,000; and (3) a small organization that is any not-for-profit
enterprise which is independently owned and operated and is not
dominant in its field. This rulemaking will affect only the small
businesses.
In accordance with section 609 of the RFA, EPA conducted an
outreach to small entities and convened a Small
[[Page 68331]]
Business Advocacy Review (SBAR) Panel prior to proposing this rule, to
obtain advice and recommendations of representatives of the small
entities that potentially would be subject to the rule's requirements.
Through the Panel process, we gathered advice and recommendations from
small-entity representatives who would be affected by the provisions in
the rule relating to large SI engines and land-based recreational
vehicles, and published the results in a Final Panel Report, dated July
17, 2001. EPA had previously convened a separate Panel for marine
engines and vessels. This panel also produced a report, dated August
25, 1999. We also prepared an Initial Regulatory Flexibility Analysis
(IRFA) in accordance with section 603 of the Regulatory Flexibility
Act. The IRFA is found in chapter 8 of the Draft Regulatory Support
Document. Both Panel reports and the IRFA have been placed in the
docket for this rulemaking (Public Docket A-2000-01, items II-A-85, II-
F-22, and III-B-01).
EPA proposed the majority of the Panel recommendations, and took
comments on these and other recommendations. The information we
received during this rulemaking process indicated that fewer small
entities would be significantly impacted by the rule than we had
originally estimated. During the SBAR Panel process, a concern was
raised that importers would have limited access to certified models for
import. We received no comments regarding this concern and believe that
the supply of four-stroke engines for ATVs and off-highway motorcycles
will continue to increase. As a result, we believe all these companies
should be able to find manufacturers that are able to supply them with
compliant engines. These importers incur no development costs, and they
are not involved in adding emission-control hardware or other variable
costs to provide a finished product to market. We also expect that the
vehicles they import would have fuel tanks and hoses that comply with
the permeation standards. However, even if this were not the case, the
additional two or three dollars that it would cost to make them
compliant with the permeation standards is trifling in comparison with
the normal selling price for these vehicles. They should therefore
expect to buy and sell their products with the normal markup to cover
their costs and profit. As noted below, we expect all 21 known small-
business importers to face compliance costs of less than one percent of
their revenues. Thus, EPA has determined that this final rule will not
have a significant economic impact on a substantial number of small
entities. We also made some changes as a result of comments received on
the proposal that we believe will further reduce the level of impact to
small entities directly regulated by the rule. These can be found below
in Section 5, ``Steps Taken to Minimize the Impact on Small Entities.''
Although this final rule will not have a significant impact on a
substantial number of small entities, EPA has prepared a Small Business
Flexibility Analysis that examines the impact of the rule on small
entities, along with regulatory alternatives that could reduce that
impact. This analysis would meet the requirements for a Final
Regulatory Flexibility Analysis (FRFA), had that analysis been
required. The Small Business Flexibility Analysis can be found in
Chapter 8 of the Final Regulatory Support Document, which is available
for review in the docket and is summarized below. The key elements of
our Small Business Flexibility Analysis include:
--The need for, and objectives of, the rule.
--The significant issues raised by public comments, a summary of the
Agency's assessment of those issues, and a statement of any changes
made to the proposed rule as a result of those comments.
--The types and number of small entities to which the rule will apply.
--The reporting, record keeping and other compliance requirement of the
rule.
--The steps taken to minimize the impact of the rule on small entities,
consistent with the stated objectives of the applicable statute.
A fuller discussion of each of these elements can be found in the
Small Business Flexibility Analysis (Chapter 8 of the Final Regulatory
Support Document).
1. The Need for and Objectives of This Rule
EPA began a study of emissions from new and existing nonroad
engines, equipment, and vehicles in 1991. In 1994, EPA finalized its
finding that nonroad engines as a whole ``are significant contributors
to ozone or carbon monoxide concentrations'' in more than one ozone or
carbon monoxide nonattainment area.\97\ Clean Air Act section 213
(a)(3) then requires EPA to establish standards for all classes and
categories of new nonroad engines that cause or contribute to ozone or
CO concentrations in more than one ozone or CO nonattainment area that
achieve the greatest degree of emissions reductions achievable taking
cost and other factors into account.
---------------------------------------------------------------------------
\97\ 59 FR 31306 (July 17, 1994).
---------------------------------------------------------------------------
Since the finding in 1994, EPA has been engaged in the process of
establishing programs to control emissions from nonroad engines used in
many different applications. Nonroad categories already regulated
include:
. Land-based compression-ignition (CI) engines (such as farm
and construction equipment),
. Small land-based spark-ignition (SI) engines (such as lawn
and garden equipment and string trimmers),
. Marine engines (outboards, personal watercraft, commercial
marine diesel, marine diesel engines under 37 kW),
. Locomotive engines.
EPA issued an Advance Notice of Proposed Rulemaking (ANPRM) on
December 7, 2000, and a Notice of Proposed Rulemaking (NPRM) on
September 14, 2001, which continued the process of establishing
standards for nonroad engines and vehicles, with proposed new emission
standards for recreational marine diesel engines, recreational
vehicles, and other nonroad spark-ignition engines over 19 kW. This
final rule includes emission standards and related requirements for
these vehicles and engines that are consistent with the requirements of
the Act.
2. Summary of Significant Issues Raised by Public Comments
We received comments from engine and equipment manufacturers and
consumers, both during the SBAR Panel process and during the comment
period after we issued the proposal. Small-volume engine and equipment
manufacturers commented on the financial hardships they would face in
complying with the proposed regulations. Most requested that we
consider hardship provisions, primarily an exemption from or a delay in
the implementation of the proposed standards, or certain flexibilities
in the certification process. Due to the wide variety of engines,
vehicles, and equipment covered by this rulemaking, we decided that a
variety of provisions were needed to address the concerns of the small
entities involved. Changes to the proposal as a result of comments from
small-entity representatives or others are noted below in Section 5 for
each of the sectors affected by this rule.
The NPRM proposed only exhaust emission controls for recreational
vehicles. However, several commenters raised the issue of control of
evaporative
[[Page 68332]]
emissions related to permeation from fuel tanks and fuel hoses. They
maintained that our obligations under section 213 of the Clean Air Act
included control of permeation emissions, and pointed to work done by
the California ARB on emissions from plastic fuel tanks and rubber fuel
line hoses, as well as from portable plastic fuel containers. Our own
investigation into hydrocarbon emissions related to permeation of fuel
tanks and fuel hoses from recreational land-based and marine
applications also supported the concerns raised by the commenters.
Therefore, on May 1, 2002, we published a notice in the Federal
Register reopening the comment period and requesting comment on
possible approaches to regulating permeation emissions from
recreational vehicles. The notice also included the expected costs and
emission reductions resulting from these approaches. Commenters were
given thirty days from May 1, 2002 to provide comments on the notice.
We received comments from several affected businesses, including at
least one small entity. These comments have been addressed in this
final rulemaking, including several changes made to the provisions as a
result of the comments.
c. Numbers and Types of Small Entities Affected
The following table provides an overview of the primary SBA small
business categories potentially affected by this regulation.
Table XI.C-1: Primary SBA Small Business Categories Potentially Affected
by This Regulation
------------------------------------------------------------------------
Defined by SBA as a small
Industry NAICS\a\ Codes business if:\b\
------------------------------------------------------------------------
Motorcycles and motorcycle 336991 <500 employees.
parts manufacturers.
Snowmobile and ATV 336999 <500 employees.
manufacturers.
Independent Commercial 421110 <100 employees.
Importers of Vehicles and
parts.
Nonroad SI engines.......... 333618 <1,000 employees.
Internal Combustion Engines. 333618 <1,000 employees.
Boat Building and Repairing. 336612 < 500 employees.
Fuel Tank Manufacturers..... 336211 <1,000 employees.
------------------------------------------------------------------------
a North American Industry Classification System
b According to SBA's regulations (13 CFR part 121), businesses with no
more than the listed number of employees or dollars in annual receipts
are considered ``small entities'' for purposes of a regulatory
flexibility analysis.
The small entities directly regulated by this rule are the
following:
a. Recreational Vehicles (ATVs, snowmobiles, and off-highway
motorcycles). The ATV sector has the broadest assortment of
manufacturers. There are seven large companies representing over 95
percent of total domestic ATV sales. The remaining 5 percent come from
small manufacturers or importers, who tend to import inexpensive,
youth-oriented ATVs from China and other Asian nations. We have
identified 21 small companies that offer off-highway motorcycles, ATVs,
or both products. Annual unit sales for these companies can range from
a few hundred to several thousand units per year.
There are three small businesses manufacturing off-highway
motorcycles in the U.S. Two of these make only competition models, so
do not need to certify their products under this regulation. The
remaining off-highway motorcycle manufacturer already offers engines
that should be meeting the new emission standards, especially under our
provisions allowing design-based certification. There is one small
business manufacturing two separate youth ATV models. This company
already uses four-stroke engines. Also, the standards are based on
emissions per watt hour, which are less costly to meet for models with
small-displacement engines. As a result, we expect both of these
manufacturers to face compliance costs less than one percent of their
revenues.
We expect all 21 small-business importers to face compliance costs
less than one percent of their revenues. These companies incur no
development costs and they are not involved in adding emission-control
hardware or other variable costs to provide a finished product to
market. As a result, they should expect to buy and sell their products
with the normal mark-up to cover their costs and profit. During the
SBAR Panel process, the concern was raised that importers might have
limited access to certified models for import. We received no comments
confirming this concern and believe that the supply of four-stroke
engines for ATVs and off-highway motorcycles will continue to increase;
as a result all these companies should be able to find manufacturers
that are able to supply compliant engines into the U.S. market.
We further believe that compliance with the permeation standards
will not place a significant burden on either the small manufacturers
or on the importers. We have estimated the incremental cost of
compliance for ATVs and off-highway motorcycles at roughly three
dollars per vehicle. This estimate includes shipping, and is based on
buying the necessary low-permeability hoses and surface treatment for
the fuel tanks from outside suppliers. Thus, no capital outlays are
required, and the increase in vehicle cost is insignificant, so that it
can easily be passed along to the ultimate consumer. However, to ensure
that these requirements do not adversely affect small manufacturers, we
are implementing, where they are applicable to permeation, the same
flexibility options we proposed for the exhaust emission standards.
Based on available industry information, four major manufacturers
account for over 99 percent of all domestic snowmobile sales. The
remaining one percent comes from very small manufacturers who tend to
specialize in unique and high-performance designs. One potential
manufacturer is not a small business, but hopes to produce snowmobiles
within the next year. Most of these manufacturers build less than 50
units per year. We have identified three small manufacturers of
snowmobiles who are still in business (of five originally identified).
Two of these companies specialize in high-performance versions of
standard recreational snowmobile types (i.e., travel and mountain
sleds). The other manufacturer produces a unique design, which is a
small scooter-like snowmobile designed to be ridden standing up. This
manufacturer provided no response to repeated outreach efforts to
determine potential economic effects of the final rule, but could be
expected to use production engines certified to the Small SI standards.
There are thus three small businesses currently producing
snowmobiles for
[[Page 68333]]
the U.S. market. One of these currently makes a mix of two-stroke and
four-stroke models and will likely rely on the provision allowing
separate standards for certain manufacturers to produce low-emitting
engines with a streamlined development effort. Estimated compliance
costs for this company are less than one percent of revenues. Costs for
the company producing the standup snowmobile should also be less than
one percent. The third manufacturer sells a single snowmobile model in
addition to a sizable business of supplying aftermarket parts for
snowmobiles from other manufacturers. We don't have revenue information
for the whole company, but with such low sales volumes, we estimate
that this company's compliance costs could reach 4-10 percent of annual
snowmobile revenues.
Control of permeation emissions was not part of the SBAR Panel
process. We received comments from one small snowmobile manufacturer
who stated that it would experience additional hardship due to the
permeation standards, because they do not have the sales volume to
install the barrier treatment for fuel tanks in-house. They also
commented that if shipping and processing of fuel tanks took 3-4
months, it would be difficult for a small business to tie up funds for
so long. However, we believe that the permeation control requirements
should be relatively easy for small businesses to meet, given the
relatively low costs involved ($5 to $7 per sled, based on outside
vendor costs). This is insignificant in comparison to the cost of the
high-end sleds that this company produces and should not materially
affect the company's cash flow. We also believe it is not necessary, or
cost-effective, for a small entity to make the capital investments for
in-house treatment facilities. Low permeation fuel hoses are available
from vendors today, and we would expect that surface treatment would be
applied through an outside company, rather than installing a treatment
facility in house. In any event, to make sure that these requirements
do not adversely affect small manufacturers, we are implementing, where
they are applicable to permeation, the same flexibility options we
proposed for the exhaust emission standards.
b. Marine Vessels. Marine vessels include the boat, engine, and
fuel system. Exhaust emission controls including NTE requirements, as
addressed in the August 29, 1999 and July 17, 2001 SBAR Panel Reports,
may affect the engine manufacturers and may affect boat builders.
We have determined that at least 16 companies manufacture marine
diesel engines for recreational vessels. Nearly 75 percent of diesel
engines sales for recreational vessels in 2000 can be attributed to
three large companies. Six of the 16 identified companies are
considered small businesses as defined by SBA. Based on sales estimates
for 2000, these six companies represent approximately 4 percent of
recreational marine diesel engine sales. The remaining companies each
comprise between two and seven percent of sales for 2000.
We are thus aware of six small businesses producing marine diesel
engines that may be considered recreational. Three of these companies
produce both commercial and recreational models without significant
differences, so we expect them to meet the standards in this final rule
with little more than the administrative expenses associated with
including recreational models in their commercial engine families.
High-performance recreational marine diesel engines already include
technologies that help control NOX emissions, so our cost
estimates include relatively modest development costs to add new
technologies. Moreover, the small-business provisions allowing
substantial additional lead time provide an opportunity for these
companies to spread development and certification costs over several
years. As a result, we expect one small business to have compliance
costs approaching one percent and one to have compliance costs between
1 and 3 percent. One very small business could have compliance costs of
about four percent of annual revenues.
c. Large Spark-ignition Engines. We are aware of two manufacturers
of Large SI engines qualifying as small businesses. One of these
companies plans to produce engines that meet the standards adopted by
California ARB in 2004, with the possible exception of one engine
family. The other company is attempting to restart the production of
engines from another failed company. This company did not exist during
the SBAR Panel process associated with this rule.
The established company will face relatively small compliance costs
as a result of this rule, since California-compliant engines will need
only a small amount of additional development effort to meet long-term
standards. These costs should be less than one percent of revenues.
The start-up company faces significant development costs, though
much of this effort is required to improve the engine enough to sustain
a market presence as other manufacturers continue to make improvements
to competitive engines. Under the hardship provisions, we expect the
start-up company to spread compliance costs over several years to
reduce the impact of emission standards. We nevertheless estimate that
the compliance costs associated with meeting EPA emission standards are
about 5 percent of revenues. Since this manufacturer is operating in a
niche market, with customers providing public comments citing the need
for these engines, we expect that most of the increased cost of
production will be recovered by increased revenues.
d. Result for all Small Entities. For this regulation as a whole,
we expect 32 small businesses to have total compliance costs less than
1 percent of their annual revenues. We estimate that one company will
have compliance costs between 1 and 3 percent of revenues. Three
companies will likely have compliance costs exceeding 3 percent of
revenues, but at least one will likely be able to benefit from the
relief provisions outlined below. These estimates include the costs for
compliance with the permeation standards.
4. Reporting, Record Keeping, and Compliance Requirements
For any emission-control program, we need assurance that the
regulated engines will meet the standards. Historically, EPA programs
have assigned manufacturers the responsibility to provide these
assurances. This final rule includes testing, reporting, and record
keeping requirements. Testing requirements for some manufacturers
include certification (including deterioration testing) and production-
line testing. Reporting and record keeping requirements include test
data and technical data on the engines, including defect reporting.
5. Steps Taken To Minimize the Impact on Small Entities
The two SBAR Panels considered a variety of provisions to reduce
the burden of complying with new emission standards and related
requirements. Some of these provisions (such as emission-credit
programs) would apply to all companies, while others would be targeted
at the unique circumstances faced by small businesses. A complete
discussion of the regulatory alternatives recommended by the Panels can
be found in the Final Panel Reports. Summaries of the Panels'
recommended alternatives for each of the sectors
[[Page 68334]]
subject to this action can also be found in their respective sections
of the preamble.
The following Panel recommendations are being finalized by the
Agency, except for a few items as noted below:
(A) Related Federal Rules
The Panel recommended that EPA continue to consult with the CPSC in
developing the rule to better understand the scope of the Commission's
regulations as they may relate to the competition exemption.
(B) Regulatory Flexibility Alternatives
The Panel recommended that EPA consider and seek comments on a wide
range of alternatives, including the flexibility options described
below. As noted above, we issued a subsequent Federal Register notice
dated May 1, 2002 (67 FR 21613), seeking comment on applying permeation
control standards for fuel tanks and fuel hoses used on recreational
vehicles. The flexibilities listed below for recreational vehicles
would generally also apply to those controls, which would effectively
extend the panel recommendations to the permeation controls as well.
(1) Large SI Engines
The Panel recommended that EPA propose several possible provisions
to address concerns that the new EPA standards could potentially place
small businesses at a competitive disadvantage to larger entities in
the industry. These provisions are described below.
(a) Using Certification and Emission Standards From Other EPA
Programs. The Panel made several recommendations for this provision.
First, the Panel recommended that EPA temporarily expand this
arrangement to allow small numbers of constant-speed engines up to 2.5
liters (up to 30kW) to be certified to the Small SI standards. Second,
the Panel further recommended that EPA seek comment on the
appropriateness of limiting the sales level of 300. Third, the Panel
recommended that EPA request comment on the anticipated cap of 30 kW on
the special treatment provisions outlined above, or whether a higher
cap on power rating is appropriate. Finally, the Panel recommended that
EPA propose to allow small-volume manufacturers producing engines up to
30kW to certify to the Small SI standards during the first 3 model
years of the program. Thereafter, the standards and test procedures
which could apply to other companies at the start of the program would
apply to small businesses. We are not adopting this provision and are
instead relying on the hardship provisions in the final rule, which
will allow us to accomplish the objective of the proposed provision
with more flexibility.
(b) Delay of Emission Standards. The Panel recommended that EPA
propose to delay the applicability of the long-term standards to small-
volume manufacturers for three years beyond the date at which they
would generally apply to accommodate the possibility that small
companies need to undertake further design work to adequately optimize
their designs and to allow them to recover the costs associated with
the near-term emission standards. We are also folding this provision
into the scope of the hardship provision, but have decided to increase
the delay to up to four years, depending on the nature of the hardship
involved.
(c) Production-Line Testing. The Panel made several recommendations
for this provision. First, the Panel recommended that EPA adopt
provisions allowing more flexibility than is available under the
California Large SI program or other EPA programs in general to address
the concern that production-line testing is another area where small-
volume manufacturers typically face a difficult testing burden. Second,
the Panel recommended that EPA allow small-volume manufacturers to have
a reduced testing rate if they have consistently good test results from
testing production-line engines. Finally, the Panel recommended that
EPA allow small-volume manufacturers to use alternative low-cost
testing options to show that production-line engines meet emission
standards.
(d) Deterioration Factors. The Panel recommended that EPA allow
small-volume manufacturers to develop deterioration factors based on
available emission measurements and good engineering judgment.
(e) Hardship Provision. The Panel recommended that EPA propose two
types of hardship provisions for Large SI engines. First the Panel
recommended that EPA allow small businesses to petition EPA for up to
three years of additional lead time to comply with the standards.
Second, the Panel recommended that EPA allow small businesses to apply
for hardship relief if circumstances outside their control cause the
failure to comply (such as a supply contract broken by a parts
supplier) and if the failure to sell the subject engines would have a
major impact on the company's solvency.
(2) Off-Highway Motorcycles and ATVs
The NPRM for this rule discussed several flexibility options for
small businesses manufacturing recreational vehicles, based on the SBAR
Panel process. When we reopened the comment period on May 1, 2002 to
request comment on possible approaches to regulating permeation
emissions from recreational vehicles, we did not specifically discuss
small business issues. However, it is our intent that these provisions
carry over to permeation controls as well.
The Panel made the following recommendations for this subcategory:
(a) General Recommendations. (1) The Panel recommended that EPA
propose to apply the flexibilities described below to engines produced
or imported by small entities with combined off-highway motorcycle and
ATV annual sales of less than 5,000 units per model year.
(2) The Panel recommended that EPA request comment on the
appropriateness of the 5,000 unit per model year threshold.
(3) The Panel recommended that EPA request comment on allowing
small entities with sales in excess of 5,000 units to certify using the
flexible approaches described below for a number of engines equal to
their 2000 or 2001 sales level.
(4) The Panel recommended that EPA describe and seek comment on the
effect of the standards on these entities, including a request for any
data and/or related studies to estimate the extent to which sales of
their products are likely to be reduced as a result of changes in
product price that are attributable to the emission standards.
(5) The Panel recommended that, in the final rule, EPA assess any
information received in response to this request for purposes of
informing the final rule decision making process on whether additional
flexibility (beyond that considered in this report) is warranted.
(b) Additional Lead-Time To Meet Emission Standards. First, the
Panel recommended that EPA propose at least a two-year delay, but seek
comment on whether a larger time period is appropriate given the costs
of compliance for small businesses and the relationship between
importers and their suppliers. Second, the Panel recommended that EPA
provide additional time for small-volume manufacturers to revise their
manufacturing process, and would allow importers to change their supply
chain to acquire complying products. Third, the Panel recommended that
EPA
[[Page 68335]]
request comment on the appropriate length for a delay (lead-time).
(c) Design Certification. The Panel recommended that EPA propose to
permit small entities to use design-based certification. The Panel also
recommended that EPA work with the small-entity representatives and
other members of the industry to develop appropriate criteria for such
design-based certification.
(d) Broaden Engine Families. The Panel recommended that EPA request
comment on engine family flexibility and conducting design-based
certification emissions testing.
(e) Production-Line Testing Waiver. The Panel recommended that EPA
propose to provide small manufacturers and small importers a waiver
from manufacturer production-line testing. The Panel also recommended
that EPA request comment on whether limits or the scope of this waiver
are appropriate.
(f) Use of Assigned Deterioration Factors During Certification. The
Panel recommended that EPA propose to provide small business with the
option to use assigned deterioration factors.
(g) Using Certification and Emission Standards from Other EPA
Programs. The Panel recommended that EPA propose to provide small
business with this flexibility through the fifth year of the program
and request comment on which of the already established standards and
programs are believed to be a useful certification option for the small
businesses.
(h) Averaging, Banking, and Trading. The Panel recommended that EPA
propose to provide small business with the same averaging, banking, and
trading program flexibilities that would apply for large manufacturers
and request comment on how the provisions could be enhanced for small
business to make them more useful.
(i) Hardship Provisions. The Panel recommended that EPA propose two
types of hardship program for off-highway motorcycles and ATVs: First,
EPA should allow small manufacturers and small importers to petition
EPA for limited additional lead-time to comply with the standards.
Second, EPA should allow small manufacturers and small importers to
apply for hardship relief if circumstances outside their control cause
the failure to comply (such as a supply contract broken by a parts
supplier) and if failure to sell the subject engines or vehicles would
have a major impact on the company's solvency.
The Panel also recommended that EPA propose both aspects of the
hardship provisions for small off-highway motorcycle and ATV
manufacturers and importers and seek comment on the implementation
provisions.
(3) Marine Vessels
(a) Delay Standards for Five Years. The Panel recommended that EPA
delay the standards for five years for small businesses.
(b) Design-Based Certification. The Panel recommended that EPA
allow manufacturers to certify by design and to be able use this to
generate credits under this approach. The Panel also recommended that
EPA provide adequately detailed design specifications and associated
emission levels for several technology options that could be used to
certify. Although we proposed this approach, we were unable to specify
any technology options for diesel engines that could be used for
design-based certification. We requested comment on such designs and
received no comment. Therefore, we are not finalizing a design-based
certification option. However, we are finalizing the engine dresser
provisions and expanding these provisions to include water-cooled
turbocharging. This will allow some engines to be exempt from the
standards based on design.
(c) Broadly Defined Product Certification Families. The Panel
recommended that EPA take comment on the need for broadly defined
emission families and how these families should be defined.
(d) Hardship Provisions. The Panel recommended that EPA propose two
types of hardship programs for marine engine manufacturers, boat
builders and fuel tank manufacturers: First, that we should allow small
businesses to petition us for additional lead time to comply with the
standards. Second, EPA should allow small businesses to apply for
hardship relief if circumstances outside their control cause the
failure to comply (such as a supply contract broken by a parts
supplier) and if the failure to sell the subject fuel tanks or boats
would have a major impact on the company's solvency. The Panel also
recommended that EPA work with small manufacturers to develop these
criteria and how they would be used.
(e) Burden Reduction Approaches Designed for Small Marinizers of
Marine Engines With Respect to NTE Provisions. The Panel recommended
that EPA specifically include NTE in a design-based approach.
(4) Snowmobiles
As noted above, permeation standards were not part of the original
NPRM for this rule, which incorporated recommendations from the SBAR
Panel process. When we reopened the comment period on May 1, 2002 to
request comment on possible approaches to regulating permeation
emissions from recreational vehicles, which would apply to snowmobiles
as well as to off-highway motorcycles and ATVs, we did not specifically
discuss small business issues. However, it is our intent that the
proposed flexibilities for exhaust emissions carry over to permeation
controls for all three vehicle categories, to the extent that they are
applicable.
(a) Delay of Emission Standards. The Panel recommended that EPA
propose to delay the standards for small snowmobile manufacturers by
two years from the date at which other manufacturers would be required
to comply. The Panel also recommended that EPA propose that the
emission standards for small snowmobile manufacturers be phased in over
an additional two year (four years to fully implement the standard).
Thus, the 2006 Phase 1 standards would be phased in at 50/100 percent
in 2008/2009, the Phase 2 standards would be phased in at 50/100
percent in 2012/2013, and the Phase 3 standards would be phased in at
50/100 percent in 2014/2015.
(b) Design-Based Certification. The Panel recommended that EPA take
comment on how design-based certification could be applied to small
snowmobile manufacturers, and that EPA work with the small entities in
the design and implementation of this concept.
(c) Broader Engine Families. The Panel recommended that EPA propose
a provision for small snowmobile manufactures that would use relaxed
criteria for what constitutes an engine or vehicle family.
(d) Elimination of Production-Line Testing Requirements. The Panel
recommended that EPA propose that small snowmobile manufacturers not be
subject to production-line testing requirements.
(e) Use of Assigned DF During Certification. The Panel recommended
that EPA propose to allow small snowmobile manufacturers to elect to
use deterioration factors determined by EPA to demonstrate end of
useful life emission levels, thus reducing development/testing burdens,
rather than performing a durability demonstration for each engine
family as part of the certification testing requirement.
(f) Using Certification and Emission Standards From Other EPA
Programs. The Panel recommended that EPA
[[Page 68336]]
propose to provide small business with the flexibility to use an engine
certified to another EPA program without recertifying it in its new
application provided that the manufacturer does not alter the engine in
such a way as to cause it to exceed the emission standards it was
originally certified to meet.
(g) Averaging, Banking and Trading. The Panel recommended that EPA
propose an averaging, banking and trading program for snowmobiles, and
seek comment on additional flexibilities related to emission credits
that should be considered for small snowmobile manufacturers.
(h) Hardship Provisions. The Panel recommended that EPA propose two
types of hardship programs for small snowmobile manufacturers. First,
EPA should allow small snowmobile manufacturers to petition EPA for
additional lead time to comply with the standards. Second, EPA should
allow small snowmobile manufacturers to apply for hardship relief if
circumstances outside their control cause the failure to comply (such
as a supply contract broken by a parts supplier) and if failure to sell
the subject engines or vehicles would have a major impact on the
company's solvency.
(i) Unique Snowmobile Engines. The Panel recommended that EPA seek
comment on an additional provision, which would allow a small
snowmobile manufacturer to petition EPA for relaxed standards for one
or more engine families. The Panel also recommended that EPA allow a
provision for EPA to set an alternative standard at a level between the
prescribed standard and the baseline level until the engine family is
retired or modified in such a way as to increase emission and for the
provision to be extended for up to 300 engines per year per
manufacturer would assure it is sufficiently available for those
manufacturers for whom the need is greatest. However, we received
comment that the limit of 300 is too restrictive to be of much
assistance to small businesses. Based on this comment we are adopting a
limit for this provision of 600 snowmobiles per year. Finally, the
Panel recommended that EPA seek comment on initial and deadline dates
for the submission of such petitions. We received no comments in this
area, but for clarity have decided to require at least nine months lead
time by the petitioner.
(5) Conclusion
In summary, considering both exhaust emission and permeation
regulations, we have found that only three small entities are likely to
be impacted by more than 3 percent of their sales, and the degree of
impact is likely to be further reduced by the flexibilities that are
being finalized in this rulemaking. Therefore, this final rule will not
have a significant economic impact on a substantial number of small
entities.
D. Unfunded Mandates Reform Act
Title II of the Unfunded Mandates Reform Act of 1995 (UMRA), Public
Law 104-4, establishes requirements for federal agencies to assess the
effects of their regulatory actions on state, local, and tribal
governments and the private sector. Under section 202 of the UMRA, EPA
generally must prepare a written statement, including a cost-benefit
analysis, for proposed and final rules with ``federal mandates'' that
may result in expenditures to state, local, and tribal governments, in
the aggregate, or to the private sector, of $100 million or more in any
one year. Before promulgating an EPA rule for which a written statement
is needed, section 205 of the UMRA generally requires EPA to identify
and consider a reasonable number of regulatory alternatives and adopt
the least costly, most cost-effective, or least burdensome alternative
that achieves the objectives of the rule. The provisions of section 205
do not apply when they are inconsistent with applicable law. Moreover,
section 205 allows EPA to adopt an alternative other than the least
costly, most cost-effective, or least burdensome alternative if the
Administrator publishes with the final rule an explanation of why that
alternative was not adopted.
Before EPA establishes any regulatory requirements that may
significantly or uniquely affect small governments, including tribal
governments, it must have developed under section 203 of the UMRA a
small government agency plan. The plan must provide for notifying
potentially affected small governments, enabling officials of affected
small governments to have meaningful and timely input in the
development of EPA regulatory proposals with significant federal
intergovernmental mandates, and informing, educating, and advising
small governments on compliance with the regulatory requirements.
This rule contains no federal mandates for state, local, or tribal
governments as defined by the provisions of Title II of the UMRA. The
rule imposes no enforceable duties on any of these governmental
entities. Nothing in the rule would significantly or uniquely affect
small governments.
EPA has determined that this rule contains federal mandates that
may result in expenditures of more than $100 million to the private
sector in any single year. EPA believes that this rule represents the
least costly, most cost-effective approach to achieve the air quality
goals of the rule. The costs and benefits associated with the rule are
discussed in Section IX and in the Small Business Support Document, as
required by the UMRA.
E. Executive Order 13132: Federalism
Executive Order 13132, entitled ``Federalism'' (64 FR 43255, August
10, 1999), requires EPA to develop an accountable process to ensure
``meaningful and timely input by State and local officials in the
development of regulatory policies that have federalism implications.''
``Policies that have federalism implications'' are defined in the
Executive Order to include regulations that have ``substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.''
Under Section 6 of Executive Order 13132, EPA may not issue a
regulation that has federalism implications, that imposes substantial
direct compliance costs, and that is not required by statute, unless
the Federal government provides the funds necessary to pay the direct
compliance costs incurred by State and local governments, or EPA
consults with State and local officials early in the process of
developing the regulation. EPA also may not issue a regulation that has
federalism implications and that preempts State law, unless the Agency
consults with State and local officials early in the process of
developing the regulation.
Section 4 of the Executive Order contains additional requirements
for rules that preempt State or local law, even if those rules do not
have federalism implications (i.e., the rules will not have substantial
direct effects on the States, on the relationship between the national
government and the states, or on the distribution of power and
responsibilities among the various levels of government). Those
requirements include providing all affected State and local officials
notice and an opportunity for appropriate participation in the
development of the regulation. If the preemption is not based on
express or implied statutory authority, EPA also must consult, to the
extent practicable, with appropriate State and local officials
regarding the conflict between State law and Federally protected
interests within the agency's area of regulatory responsibility.
[[Page 68337]]
This rule does not have federalism implications. It will not have
substantial direct effects on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government, as
specified in Executive Order 13132.
Although Section 6 of Executive Order 13132 does not apply to this
rule, EPA did consult with representatives of various State and local
governments in developing this rule. EPA has also consulted
representatives from STAPPA/ALAPCO, which represents state and local
air pollution officials.
F. Executive Order 13175: Consultation and Coordination With Indian
Tribal Governments
Executive Order 13175, entitled ``Consultation and Coordination
with Indian Tribal Governments'' (59 FR 22951, November 6, 2000),
requires EPA to develop an accountable process to ensure ``meaningful
and timely input by tribal officials in the development of regulatory
policies that have tribal implications.'' ``Policies that have tribal
implications'' is defined in the Executive Order to include regulations
that have ``substantial direct effects on one or more Indian tribes, on
the relationship between the Federal government and the Indian tribes,
or on the distribution of power and responsibilities between the
Federal government and Indian tribes.''
This rule does not have tribal implications. It will not have
substantial direct effects on tribal governments, on the relationship
between the Federal government and Indian tribes, or on the
distribution of power and responsibilities between the Federal
government and Indian tribes, as specified in Executive Order 13175.
The emission standards and other related requirements for private
businesses in this rule have national applicability and therefore do
not uniquely affect the communities of Indian Tribal Governments.
Further, no circumstances specific to such communities exist that would
cause an impact on these communities beyond those discussed in the
other sections of this rule. Thus, Executive Order 13175 does not apply
to this rule.
G. Executive Order 13045: Protection of Children From Environmental
Health and Safety Risks
Executive Order 13045, ``Protection of Children from Environmental
Health Risks and Safety Risks'' (62 FR 19885, April 23, 1997) applies
to any rule that (1) is determined to be ``economically significant''
as defined under Executive Order 12866, and (2) concerns an
environmental health or safety risk that EPA has reason to believe may
have a disproportionate effect on children. If the regulatory action
meets both criteria, Section 5-501 of the Order directs the Agency to
evaluate the environmental health or safety effects of the planned rule
on children, and explain why the planned regulation is preferable to
other potentially effective and reasonably feasible alternatives
considered by the Agency.
This rule is not subject to the Executive Order because it does not
involve decisions on environmental health or safety risks that may
disproportionately affect children.
The effects of ozone and PM on children's health were addressed in
detail in EPA's rulemaking to establish the NAAQS for these pollutants,
and EPA is not revisiting those issues here. EPA believes, however,
that the emission reductions from the strategies in this rulemaking
will further reduce air toxics and the related adverse impacts on
children's health.
H. Executive Order 13211: Actions That Significantly Affect Energy
Supply, Distribution, or Use
This rule is not a ``significant energy action'' as defined in
Executive Order 13211, ``Actions Concerning Regulations That
Significantly Affect Energy Supply, Distribution, or Use'' (66 FR 28355
(May 22, 2001)) because it is not likely to have a significant adverse
effect on the supply, distribution or use of energy. The aim to reduce
emissions from certain nonroad engines and have no effect on fuel
formulation, distribution, or use. Generally, the final rule leads to
reduced fuel usage due to the improvements in engine-based emission-
control technologies.
I. National Technology Transfer and Advancement Act
Section 12(d) of the National Technology Transfer and Advancement
Act of 1995 (``NTTAA''), Public Law 104-113, section 12(d) (15 U.S.C.
272 note) directs EPA to use voluntary consensus standards in its
regulatory activities unless doing so would be inconsistent with
applicable law or otherwise impractical. Voluntary consensus standards
are technical standards (such as materials specifications, test
methods, sampling procedures, and business practices) that are
developed or adopted by voluntary consensus standards bodies. NTTAA
directs EPA to provide Congress, through OMB, explanations when the
Agency decides not to use available and applicable voluntary consensus
standards.
This rule involves technical standards. The following paragraphs
describe how we specify testing procedures for engines subject to this
rule.
The International Organization for Standardization (ISO) has a
voluntary consensus standard that can be used to test Large SI engines.
However, the current version of that standard (ISO 8178) is applicable
only for steady-state testing, not for transient testing. As described
in the Final Regulatory Support Document, transient testing is an
important part of the emission-control program for these engines. We
are therefore not adopting the ISO procedures in this rulemaking.
Underwriters Laboratories (UL) has adopted voluntary consensus
standards for forklifts that are relevant to the new requirements for
Large SI engines. UL sets a maximum temperature specification for
gasoline and, for forklifts used in certain applications, defines
requirements to avoid venting from gasoline fuel tanks. We are adopting
a different temperature limit, because the maximum temperature
specified by UL does not prevent fuel boiling. We are adopting separate
measures to address venting of gasoline vapors, because of UL's
provisions to allow venting with an orifice up to 1.78 mm (0.070
inches). We believe forklifts with such a vent would have unnecessarily
high evaporative emissions. If the UL standard is revised to address
these technical concerns, it would be appropriate to reference the UL
standard in our regulations. An additional concern relates to the fact
that the UL requirements apply only to forklifts (and not all forklifts
in the case of the restriction on vapor venting). EPA regulations would
therefore need to, at a minimum, extend any published UL standards to
other engines and equipment to which the UL standards would otherwise
not apply.
The Gas Processors Association has adopted standards with fuel
specifications for liquefied petroleum gas. However, there is no
existing regulations requiring suppliers to meet these specifications.
Comments received on the rule indicate a high level of concern that in-
use fuel quality does not meet the published voluntary standards, so we
are not relying on these fuel specifications to define fuels for
certification testing.
We are adopting requirements to test off-highway motorcycles and
all-terrain vehicles with the Federal Test Procedure, a chassis-based
transient test. There is no voluntary consensus
[[Page 68338]]
standard that would adequately address engine or vehicle operation for
suitable emission measurement. Furthermore, we are interested in
pursuing an engine-based test procedure for all-terrain vehicles. We
intend to develop a new duty cycle for this, because there is no
acceptable engine duty cycle today that would adequately represent the
way these engines operate. For snowmobiles, we are adopting test
procedures based on work that has been published, but not yet adopted
as a voluntary consensus standard.
For recreational marine diesel engines, we are adopting the same
test procedures that we have established for commercial marine diesel
engines (with a new duty cycle appropriate for recreational
applications). We are again adopting these procedures in place of the
ISO 8178 standard that would apply to these engines. We believe that
ISO 8178 relies too heavily on reference testing conditions. Because
our test procedures need to represent in-use operation typical of
operation in the field, they must be based on a range of ambient
conditions. We determined that the ISO procedures are not broadly
usable in their current form, and therefore should not be adopted by
reference. We remain hopeful that future ISO test procedures will be
developed that are usable and accurate for the broad range of testing
needed, and that such procedures could then be adopted. We expect that
any such development of revised test procedures will be done in
accordance with ISO procedures and in a balanced and transparent manner
that includes the involvement of all interested parties, including
industry, U.S. EPA, foreign government organizations, state
governments, and environmental groups. In so doing, we believe that the
resulting procedures would be ``global'' test procedures that can
facilitate the free flow of international commerce for these products.
J. Congressional Review Act
The Congressional Review Act, 5 U.S.C. 801 et seq., as added by the
Small Business Regulatory Enforcement Fairness Act of 1996, generally
provides that before a rule may take effect, the agency promulgating
the rule must submit a rule report, which includes a copy of the rule,
to each House of the Congress and to the Comptroller General of the
United States. EPA will submit a report containing this rule and other
required information to the U.S. Senate, the U.S. House of
Representatives, and the Comptroller General of the United States prior
to publication of the rule in the Federal Register. This rule is a
``major rule'' as defined by 5 U.S.C. 804(2).
K. Plain Language
This document follows the guidelines of the June 1, 1998 Executive
Memorandum on Plain Language in Government Writing. To read the text of
the regulations, it is also important to understand the organization of
the Code of Federal Regulations (CFR). The CFR uses the following
organizational names and conventions.
Title 40--Protection of the Environment
Chapter I--Environmental Protection Agency
Subchapter C--Air Programs. This contains parts 50 to 99, where the
Office of Air and Radiation has usually placed emission standards for
motor vehicle and nonroad engines.
Subchapter U--Air Programs Supplement. This contains parts 1000 to
1299, where we intend to place regulations for air programs in future
rulemakings.
Part 1048--Control of Emissions from New, Large, Nonrecreational,
Nonroad Spark-ignition Engines. Most of the provisions in this part
apply only to engine manufacturers.
Part 1051--Control of Emissions from Recreational Engines and
Vehicles. Most of the provisions in this part apply only to vehicle
manufacturers.
Part 1065--General Test Procedures for Engine Testing. Provisions
of this part apply to anyone who tests engines to show that they meet
emission standards.
Part 1068--General Compliance Provisions for Engine Programs.
Provisions of this part apply to everyone.
Each part in the CFR has several subparts, sections, and
paragraphs. The following illustration shows how these fit together.
Part 1048
Subpart A
Section 1048.1
(a)
(b)
(1)
(2)
(i)
(ii)
A cross reference to Sec. 1048.1(b) in this illustration would
refer to the parent paragraph (b) and all its subordinate paragraphs. A
reference to Sec. 1048.1(b) introductory text'' would refer only to
the single, parent paragraph (b).
List of Subjects
40 CFR Part 89
Environmental protection, Administrative practice and procedure,
Confidential business information, Imports, Labeling, Motor vehicle
pollution, Reporting and recordkeeping requirements, Research, Vessels,
Warranties.
40 CFR Part 90
Environmental protection, Administrative practice and procedure,
Air pollution control, Confidential business information, Imports,
Labeling, Reporting and recordkeeping requirements, Research,
Warranties.
40 CFR Part 91
Environmental protection, Administrative practice and procedure,
Air pollution control, Confidential business information, Imports,
Labeling, Penalties, Reporting and recordkeeping requirements,
Warranties.
40 CFR Part 94
Environmental protection, Administrative practice and procedure,
Air pollution control, Confidential business information, Imports,
Penalties, Reporting and recordkeeping requirements, Vessels,
Warranties.
40 CFR Part 1048
Environmental protection, Administrative practice and procedure,
Air pollution control, Confidential business information, Imports,
Incorporation by reference, Labeling, Penalties, Reporting and
recordkeeping requirements, Research, Warranties.
40 CFR Part 1051
Environmental protection, Administrative practice and procedure,
Air pollution control, Confidential business information, Imports,
Incorporation by reference, Labeling, Penalties, Reporting and
recordkeeping requirements, Warranties.
40 CFR Part 1065
Environmental protection, Administrative practice and procedure,
Incorporation by reference, Reporting and recordkeeping requirements,
Research.
40 CFR Part 1068
Environmental protection, Administrative practice and procedure,
Confidential business information, Imports, Motor vehicle pollution,
Penalties, Reporting and recordkeeping requirements, Warranties.
[[Page 68339]]
Dated: September 13, 2002.
Christine Todd Whitman,
Administrator.
For the reasons set out in the preamble, title 40, chapter I of the
Code of Federal Regulations is amended as set forth below.
PART 89--CONTROL OF EMISSIONS FROM NEW AND IN-USE NONROAD
COMPRESSION-IGNITION ENGINES
1. The authority for part 89 continues to read as follows:
Authority: 42 U.S.C. 7521, 7522, 7523, 7524, 7525, 7541, 7542,
7543, 7545, 7547, 7549, 7550, and 7601(a).
Subpart A--[Amended]
2. Section 89.2 is amended by adding definitions for ``Aircraft'',
``Spark-ignition'', and ``United States'' in alphabetic order and
revising the definition of ``Compression-ignition'' to read as follows:
Sec. 89.2 Definitions.
* * * * *
Aircraft means any vehicle capable of sustained air travel above
treetop heights.
* * * * *
Compression-ignition means relating to a type of reciprocating,
internal-combustion engine that is not a spark-ignition engine.
* * * * *
Spark-ignition means relating to a gasoline-fueled engine or other
engines with a spark plug (or other sparking device) and with operating
characteristics significantly similar to the theoretical Otto
combustion cycle. Spark-ignition engines usually use a throttle to
regulate intake air flow to control power during normal operation.
* * * * *
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
* * * * *
Subpart B--[Amended]
3. Section 89.106 is amended by revising paragraph (b) read as
follows:
Sec. 89.106 Prohibited controls.
* * * * *
(b) You may not design your engines with emission-control devices,
systems, or elements of design that cause or contribute to an
unreasonable risk to public health, welfare, or safety while operating.
For example, this would apply if the engine emits a noxious or toxic
substance it would otherwise not emit that contributes to such an
unreasonable risk.
PART 90--CONTROL OF EMISSIONS FROM NONROAD SPARK-IGNITION ENGINES
AT OR BELOW 19 KILOWATTS
4. The heading to part 90 is revised to read as set forth above.
5. The authority for part 90 continues to read as follows:
Authority: 42 U.S.C. 7521, 7522, 7523, 7524, 7525, 7541, 7542,
7543, 7547, 7549, 7550, and 7601(a).
Subpart A--[Amended]
6. Section 90.1 is revised to read as follows:
Sec. 90.1 Applicability.
(a) This part applies to new nonroad spark-ignition engines and
vehicles with gross power output at or below 19 kilowatts (kW) used for
any purpose, unless we exclude them under paragraph (d) of this
section.
(b) This part also applies to engines with a gross power output
above 19 kW if the manufacturer uses the provisions of 40 CFR 1048.615
or 1051.145(a)(3) to exempt them from the requirements of 40 CFR part
1048 or 1051, respectively. Compliance with the provisions of this part
is a required condition of those exemptions.
(c) [Reserved]
(d) The following nonroad engines and vehicles are not subject to
the provisions of this part:
(1) Engines certified to meet the requirements of 40 CFR part 1051
(e.g., engines used in snowmobiles). This part nevertheless applies to
engines used in recreational vehicles if the manufacturer uses the
provisions of 40 CFR 1051.145(a)(3) to exempt them from the
requirements of 40 CFR part 1051. Compliance with the provisions of
this part is a required condition of that exemption.
(2) Engines used in highway motorcycles. See 40 CFR part 86,
subpart E.
(3) Propulsion marine engines. See 40 CFR part 91. This part
applies with respect to auxiliary marine engines.
(4) Engines used in aircraft. See 40 CFR part 87.
(5) Engines certified to meet the requirements of 40 CFR part 1048.
(6) Hobby engines.
(7) Engines that are used exclusively in emergency and rescue
equipment where no certified engines are available to power the
equipment safely and practically, but not including generators,
alternators, compressors or pumps used to provide remote power to a
rescue tool. The equipment manufacturer bears the responsibility to
ascertain on an annual basis and maintain documentation available to
the Administrator that no appropriate certified engine is available
from any source.
(e) Engines subject to the provisions of this subpart are also
subject to the provisions found in subparts B through N of this part,
except that Subparts C, H, M and N of this part apply only to Phase 2
engines as defined in this subpart.
(f) Certain text in this part is identified as pertaining to Phase
1 or Phase 2 engines. Such text pertains only to engines of the
specified Phase. If no indication of Phase is given, the text pertains
to all engines, regardless of Phase.
7. Section 90.2 is amended by adding a new paragraph (c) to read as
follows:
Sec. 90.2 Effective dates.
* * * * *
(c) Notwithstanding paragraphs (a) and (b) of this section, engines
used
in recreational vehicles with engine rated speed greater than or
equal to 5,000 rpm and with no installed speed governor are not subject
to the provisions of this part through the 2005 model year. Starting
with the 2006 model year, all the requirements of this part apply to
engines used in these vehicles if they are not included in the scope of
40 CFR part 1051.
8. Section 90.3 is amended by adding definitions for ``Aircraft'',
``Hobby engines'', ``Marine engine'', ``Marine vessel'',
``Recreational'', and ``United States'' in alphabetical order, to read
as follows:
Sec. 90.3 Definitions.
* * * * *
Aircraft means any vehicle capable of sustained air travel above
treetop heights.
* * * * *
Hobby engines means engines used in reduced-scale models of
vehicles that are not capable of transporting a person (for example,
model airplanes).
Marine engine means an engine that someone installs or intends to
install on a marine vessel. There are two kinds of marine engines:
(1) Propulsion marine engine means a marine engine that moves a
vessel through the water or directs the vessel's movement.
(2) Auxiliary marine engine means a marine engine not used for
propulsion.
[[Page 68340]]
Marine vessel means a vehicle that is capable of operation in water
but is not capable of operation out of water. Amphibious vehicles are
not marine vessels.
* * * * *
Recreational means, for purposes of this part, relating to a
vehicle intended by the vehicle manufacturer to be operated primarily
for pleasure.
* * * * *
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
* * * * *
Subpart B--[Amended]
9. Section 90.103 is amended by redesignating paragraph (a)(2)(v)
as paragraph (a)(2)(vi) and adding a new paragraph (a)(2)(v) to read as
follows:
Sec. 90.103 Exhaust emission standards.
(a)* * *
(2)* * *
(v) The engine must be used in a recreational application, with a
combined total vehicle dry weight under 20 kilograms;
* * * * *
10. Section 90.110 is amended by revising paragraph (b) to read as
follows:
Sec. 90.110 Requirement of certification--prohibited controls.
* * * * *
(b) You may not design your engines with emission-control devices,
systems, or elements of design that cause or contribute to an
unreasonable risk to public health, welfare, or safety while operating.
For example, this would apply if the engine emits a noxious or toxic
substance it would otherwise not emit that contributes to such an
unreasonable risk.
PART 91--CONTROL OF EMISSIONS FROM MARINE SPARK-IGNITION ENGINES
11. The authority for part 91 continues to read as follows:
Authority: 42 U.S.C. 7521, 7522, 7523, 7524, 7525, 7541, 7542,
7543, 7547, 7549, 7550, and 7601(a).
Subpart A--[Amended]
12. Section 91.3 is amended by adding the definition for ``United
States'' in alphabetical order to read as follows:
Sec. 91.3 Definitions.
* * * * *
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
* * * * *
Subpart B--[Amended]
13. Section 91.110 is amended by revising paragraph (b) to read as
follows:
Sec. 91.110 Requirement of certification--prohibited controls.
* * * * *
(b) You may not design your engines with emission-control devices,
systems, or elements of design that cause or contribute to an
unreasonable risk to public health, welfare, or safety while operating.
For example, this would apply if the engine emits a noxious or toxic
substance it would otherwise not emit that contributes to such an
unreasonable risk.
Subpart E--[Amended]
14. Section 91.419 is amended in paragraph (b) by revising the
equations for MHCexh and Mexh to read as follows:
Sec. 91.419 Raw emission sampling calculations.
* * * * *
(b) * * *
MHCexh = 12.01 + 1.008 x [alpha]
* * * * *
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.001
* * * * *
Subpart G--[Amended]
15. Appendix A to Subpart G of part 91 is amended by revising Table
1 to read as follows:
Appendix A to Subpart G of Part 91--Sampling Plans for Selective
Enforcement Auditing of Marine Engines
Table 1.--Sampling Plan Code Letter
------------------------------------------------------------------------
Annual engine family sales Code letter
------------------------------------------------------------------------
20-50.................................... AA \1\
20-99.................................... A \1\
100-299.................................. B
300-499.................................. C
500 or greater........................... D
------------------------------------------------------------------------
\1\ A manufacturer may optionally use either the sampling plan for code
letter ``AA'' or sampling plan for code letter ``A'' for Selective
Enforcement Audits of engine families with annual sales between 20 and
50 engines. Additional, the manufacturers may switch between these
plans during the audit.
* * * * *
Subpart I--[Amended]
16. Section 91.803 is amended by revising paragraph (a) to read as
follows:
Sec. 91.803 Manufacturer in-use testing program.
(a) EPA shall annually identify engine families and those
configurations within families which the manufacturers must then
subject to in-use testing. For each model year, EPA may identify the
following number of engine families for testing, based on the number of
the manufacturer's engine families to which this subpart is applicable
produced in that model year:
[[Continued on page 68341]]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
]
[[pp. 68341-68390]]
Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
[[Continued from page 68340]]
[[Page 68341]]
(1) For manufactures with three or fewer engine families, EPA may
identify a single engine family.
(2) For manufacturers with four or more engine families, EPA may
identify a number of engine families that is no greater than twenty-
five percent of the number of engine families to which this subpart is
applicable that are produced by the manufacturer in that model year.
* * * * *
PART 94--CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION
ENGINES
17. The heading to part 94 is revised to read as set forth above.
18. The authority citation for part 94 continues to read as
follows:
Authority: 42 U.S.C. 7522, 7523, 7524, 7525, 7541, 7542, 7543,
7545, 7547, 7549, 7550 and 7601(a).
Subpart A--[Amended]
19. Section 94.1 is revised to read as follows:
Sec. 94.1 Applicability.
(a) Except as noted in paragraphs (b) and (c) of this section, the
provisions of this part apply to manufacturers (including post-
manufacture marinizers and dressers), rebuilders, owners and operators
of:
(1) Marine engines that are compression-ignition engines
manufactured (or that otherwise become new) on or after January 1,
2004;
(2) Marine vessels manufactured (or that otherwise become new) on
or after January 1, 2004 and which include a compression-ignition
marine engine.
(b) Notwithstanding the provision of paragraph (c) of this section,
the requirements and prohibitions of this part do not apply to three
types of marine engines:
(1) Category 3 marine engines;
(2) Marine engines with rated power below 37 kW; or
(3) Marine engines on foreign vessels.
(c) The provisions of Subpart L of this part apply to everyone with
respect to the engines identified in paragraph (a) of this section.
20. Section 94.2 is amended by revising paragraph (b) introductory
text, removing the definition for ``Commercial marine engine'',
revising definitions for ``Compression-ignition'', ``Designated
officer'', ``Passenger'', ``Recreational marine engine'',
``Recreational vessel'', and ``United States'', and adding new
definitions for ``Commercial'', ``Small-volume boat builder'', ``Small-
volume manufacturer'', and ``Spark-ignition'' in alphabetical order to
read as follows:
Sec. 94.2 Definitions.
* * * * *
(b) As used in this part, all terms not defined in this section
shall have the meaning given them in the Act:
* * * * *
Commercial means relating to an engine or vessel that is not a
recreational marine engine or a recreational vessel.
* * * * *
Compression-ignition means relating to an engine that is not a
spark-ignition engine.
* * * * *
Designated Officer means the Manager, Engine Programs Group (6403-
J), U.S. Environmental Protection Agency, 1200 Pennsylvania Ave.,
Washington, DC 20460.
* * * * *
Passenger has the meaning given by 46 U.S.C. 2101 (21) and (21a).
In the context of commercial vessels, this generally means that a
passenger is a person that pays to be on the vessel.
* * * * *
Recreational marine engine means a Category 1 propulsion marine
engine that is intended by the manufacturer to be installed on a
recreational vessel, and which is permanently labeled as follows:
``THIS ENGINE IS CATEGORIZED AS A RECREATIONAL MARINE ENGINE UNDER 40
CFR PART 94. INSTALLATION OF THIS ENGINE IN ANY NONRECREATIONAL VESSEL
IS A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTY.''.
Recreational vessel has the meaning given in 46 U.S.C. 2101 (25),
but excludes ``passenger vessels'' and ``small passenger vessels'' as
defined by 46 U.S.C. 2101 (22) and (35) and excludes vessels used
solely for competition. In general, for this part, ``recreational
vessel'' means a vessel that is intended by the vessel manufacturer to
be operated primarily for pleasure or leased, rented or chartered to
another for the latter's pleasure, excluding the following vessels:
(1) Vessels of less than 100 gross tons that carry more than 6
passengers (as defined in this section).
(2) Vessels of 100 gross tons or more that carry one or more
passengers (as defined in this section).
(3) Vessels used solely for competition.
* * * * *
Small-volume boat builder means a boat manufacturer with fewer than
500 employees and with annual U.S.-directed production of fewer than
100 boats. For manufacturers owned by a parent company, these limits
apply to the combined production and number of employees of the parent
company and all its subsidiaries.
Small-volume manufacturer means a manufacturer with annual U.S.-
directed production of fewer than 1,000 internal combustion engines
(marine and nonmarine). For manufacturers owned by a parent company,
the limit applies to the production of the parent company and all its
subsidiaries.
Spark-ignition means relating to a gasoline-fueled engine or other
engines with a spark plug (or other sparking device) and with operating
characteristics significantly similar to the theoretical Otto
combustion cycle. Spark-ignition engines usually use a throttle to
regulate intake air flow to control power during normal operation.
* * * * *
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
* * * * *
21. Section 94.7 is amended by revising paragraphs (c), (d), and
(e) to read as follows:
Sec. 94.7 General standards and requirements.
* * * * *
(c) You may not design your engines with emission-control devices,
systems, or elements of design that cause or contribute to an
unreasonable risk to public health, welfare, or safety while operating.
For example, this would apply if the engine emits a noxious or toxic
substance it would otherwise not emit that contributes to such an
unreasonable risk.
(d) All engines subject to the emission standards of this part
shall be equipped with a connection in the engine exhaust system that
is located downstream of the engine and before any point at which the
exhaust contacts water (or any other cooling/scrubbing medium) for the
temporary attachment of gaseous and/or particulate emission sampling
equipment. This connection shall be internally threaded with standard
pipe threads of a size not larger than one-half inch, and shall be
closed by a pipe-plug when not in use. Equivalent connections are
allowed. Engine manufacturers may comply with this requirement by
providing vessel manufacturers with clear instructions explaining how
to meet this requirement, and noting in the instructions that failure
to comply may
[[Page 68342]]
invalidate a certificate and subject the vessel manufacturer to federal
penalties.
(e) Electronically controlled engines subject to the emission
standards of this part shall broadcast on engine's controller area
networks engine torque (as percent of maximum torque at that speed) and
engine speed.
22. Section 94.8 is amended by revising paragraphs (a), (e), (f)
introductory text, and (f)(1) to read as follows:
Sec. 94.8 Exhaust emission standards.
(a) Exhaust emissions from marine compression-ignition engines
shall not exceed the applicable exhaust emission standards contained in
Table A-1 as follows:
Table A-1.--Primary Tier 2 Exhaust Emission Standards (g/kW-hr)
----------------------------------------------------------------------------------------------------------------
Engine size liters/cylinder, rated Model THC+NOX CO g/kW- PM g/kW-
power Category yeara g/kW-hr hr hr
----------------------------------------------------------------------------------------------------------------
Disp. < 0.9 and......................... Category 1, Commercial.... 2005 7.5 5.0 0.40
power £= 37 kW................
Category 1, Recreational.. 2007 7.5 5.0 0.40
0.9 <= disp. < 1.2...................... Category 1, Commercial.... 2004 7.2 5.0 0.30
All power levels........................
Category 1, Recreational.. 2006 7.2 5.0 0.30
1.2 <= disp. < 2.5...................... Category 1, Commercial.... 2004 7.2 5.0 0.20
All power levels........................
Category 1, Recreational.. 2006 7.2 5.0 0.20
2.5 <= disp. < 5.0...................... Category 1, Commercial.... 2007 7.2 5.0 0.20
All power levels........................
Category 1, Recreational.. 2009 7.2 5.0 0.20
5.0 <= disp. < 15.0..................... Category 2................ 2007 7.8 5.0 0.27
All power levels........................
15.0 <= disp. < 20.0.................... Category 2................ 2007 8.7 5.0 0.50
Power < 3300 kW.........................
15.0 <= disp. < 20.0.................... Category 2................ 2007 9.8 5.0 0.50
Power < 3300 kW.........................
20.0 <= disp. < 25.0.................... Category 2................ 2009 9.8 5.0 0.50
All power levels........................
25.0 <= disp. < 30.0.................... Category 2................ 2007 11.0 5.0 0.50
All power levels........................
----------------------------------------------------------------------------------------------------------------
\a\ The dates listed indicate the model years for which the specified standards start.
* * * * *
(e) Exhaust emissions from propulsion engines subject to the
standards (or FELs) in paragraph (a), (c), or (f) of this section shall
not exceed:
(1) Commercial marine engines. (i) 1.20 times the applicable
standards (or FELs) when tested in accordance with the supplemental
test procedures specified in Sec. 94.106 at loads greater than or
equal to 45 percent of the maximum power at rated speed or 1.50 times
the applicable standards (or FELs) at loads less than 45 percent of the
maximum power at rated speed.
(ii) As an option, the manufacturer may choose to comply with
limits of 1.25 times the applicable standards (or FELs) when tested
over the whole power range in accordance with the supplemental test
procedures specified in Sec. 94.106, instead of the limits in
paragraph (e)(1)(i) of this section.
(2) Recreational marine engines. (i) 1.20 times the applicable
standards (or FELs) when tested in accordance with the supplemental
test procedures specified in Sec. 94.106 at loads greater than or
equal to 45 percent of the maximum power at rated speed and speeds less
than 95 percent of maximum test speed, or 1.50 times the applicable
standards (or FELs) at loads less than 45 percent of the maximum power
at rated speed, or 1.50 times the applicable standards (or FELs) at any
loads for speeds greater than or equal to 95 percent of the maximum
test speed.
(ii) As an option, the manufacturer may choose to comply with
limits of 1.25 times the applicable standards (or FELs) when tested
over the whole power range in accordance with the supplemental test
procedures specified in Sec. 94.106, instead of the limits in
paragraph (e)(2)(i) of this section.
(f) The following defines the requirements for low-emitting Blue
Sky Series engines:
(1) Voluntary standards. Engines may be designated ``Blue Sky
Series'' engines through the 2012 model year by meeting the voluntary
standards listed in Table A-2, which apply to all certification and in-
use testing, as follows:
Table A-2.--Voluntary Emission Standards (g/kW-hr)
------------------------------------------------------------------------
Rated brake power (kW) THC+NOX PM
------------------------------------------------------------------------
Power £=37 kW, and displ.<0.9. 4.0 0.24
0.9<=displ.<1.2......................... 4.0 0.18
1.2<=displ.<2.5......................... 4.0 0.12
2.5<=displ.<5........................... 5.0 0.12
5<=displ.<15............................ 5.0 0.16
15 <=disp.< 20, and power < 3300 kW..... 5.2 0.30
15 <=disp.< 20, and power £= 5.9 0.30
3300 kW................................
20 <=disp.< 25.......................... 5.9 0.30
25 <=disp.< 30.......................... 6.6 0.30
------------------------------------------------------------------------
[[Page 68343]]
* * * * *
23. Section 94.9 is amended by revising paragraphs (a) introductory
text and (a)(1) to read as follows:
Sec. 94.9 Compliance with emission standards.
(a) The general standards and requirements in Sec. 94.7 and the
emission standards in Sec. 94.8 apply to each new engine throughout
its useful life period. The useful life is specified both in years and
in hours of operation, and ends when either of the values (hours of
operation or years) is exceeded.
(1) The minimum useful life is:
(i) 10 years or 1,000 hours of operation for recreational Category
1 engines;
(i) 10 years or 10,000 hours of operation for commercial Category 1
engines;
(iii) 10 years or 20,000 hours of operation for Category 2 engines.
* * * * *
24. Section 94.12 is amended by revising the introductory text and
paragraphs (a), (b)(1), and (e) and adding new paragraphs (f) and (g)
to read as follows:
Sec. 94.12 Interim provisions.
This section contains provisions that apply for a limited number of
calendar years or model years. These provisions apply instead of the
other provisions of this part.
(a) Compliance date of standards. Certain companies may delay
compliance with emission standards. Companies wishing to take advantage
of this provision must inform the Designated Officer of their intent to
do so in writing before the date that compliance with the standards
would otherwise be mandatory.
(1) Post-manufacture marinizers may elect to delay the model year
of the Tier 2 standards for commercial engines as specified in Sec.
94.8 by one year for each engine family.
(2) Small-volume manufacturers may elect to delay the model year of
the Tier 2 standards for recreational engines as specified in Sec.
94.8 by five years for each engine family.
(b) Early banking of emission credits. (1) A manufacturer may
optionally certify engines manufactured before the date the Tier 2
standards take effect to earn emission credits under the averaging,
banking, and trading program. Such optionally certified engines are
subject to all provisions relating to mandatory certification and
enforcement described in this part. Manufacturers may begin earning
credits for recreational engines on December 9, 2002.
* * * * *
(e) Compliance date of NTE requirements (1) Notwithstanding the
other provisions of this part, the requirements of Sec. 94.8(e) for
commercial marine engines start with 2010 model year engines for
postmanufacture marinizers and 2007 model year engines for all other
engine manufacturers.
(2) Notwithstanding the other provisions of this part, the
requirements of Sec. 94.8(e) for recreational marine engines start
with 2012 model year engines for post-manufacture marinizers and 2009
model year engines for all other engine manufacturers.
(f) Flexibility for small-volume boat builders. Notwithstanding the
other provisions of this part, manufacturers may sell uncertified
recreational engines to small-volume boat builders during the first
five years for which the emission standards in Sec. 94.8 apply,
subject to the following provisions:
(1) The U.S.-directed production volume of boats from any small-
volume boat builder using uncertified engines during the total five-
year period may not exceed 80 percent of the manufacturer's average
annual production for the three years prior to the general
applicability of the recreational engine standards in Sec. 94.8,
except as allowed in paragraph (f)(2) of this section.
(2) Small-volume boat builders may exceed the production limits in
paragraph (f)(1) of this section, provided they do not exceed 20 boats
during the five-year period or 10 boats in any single calendar year.
This does not apply to boats powered by engines with displacement
greater than 2.5 liters per cylinder.
(3) Small-volume boat builders must keep records of all the boats
and engines produced under this paragraph (f), including boat and
engine model numbers, serial numbers, and dates of manufacture. Records
must also include information verifying compliance with the limits in
paragraph (f)(1) or (f)(2) of this section. Keep these records until at
least two full years after you no longer use the provisions in this
paragraph (f).
(4) Manufacturers must add a permanent, legible label, written in
block letters in English, to a readily visible part of each engine
exempted under this paragraph (f). This label must include at least the
following items:
(i) The label heading ``EMISSION CONTROL INFORMATION''.
(ii) Your corporate name and trademark.
(iii) Engine displacement (in liters), rated power, and model year
of the engine or whom to contact for further information.
(iv) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 94.12(f)
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
(g) Flexibility for engines over 560kW. Notwithstanding the other
provisions of this part, manufacturers may choose to delay
certification of marine engines with less than 2.5 liters per cylinder
and rated power above 560 kW, that are derived from a land-based
nonroad engine with a rated power greater than 560 kW, if they do all
of the following:
(1) Certify all of their applicable marine engines with less than
2.5 liters per cylinder and rated power above 560 kW to a
NOX standard of 6.4 g/kW-hr for model years 2008 through
2012.
(2) Notify EPA in writing before 2004 of their intent to use this
provision. This notification must include a signed statement certifying
that the manufacturer will comply with all the provisions of this
paragraph (g).
(3) Add a permanent, legible label, written in block letters in
English, to a readily visible part of each engine exempted under this
paragraph (f). This label must include at least the following items:
(i) The label heading ``EMISSION CONTROL INFORMATION''.
(ii) Your corporate name and trademark.
(iii) Engine displacement (in liters), rated power, and model year
of the engine or whom to contact for further information.
(iv) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 94.12(g)
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
Subpart B--[Amended]
25. Section 94.104 is amended by redesignating paragraph (c) as
paragraph (d) and adding a new paragraph (c) to read as follows:
Sec. 94.104 Test procedures for Category 2 marine engines.
* * * * *
(c) Conduct testing at ambient temperatures from 13[deg]
C to
30[deg]
C.
* * * * *
26. Section 94.105 is amended by revising paragraph (b) text
preceding Table B-1, revising ``i
'' to read ``+/-'' in
footnotes 1 and 2 in the tables in paragraphs (b), (c)(1), (c)(2), and
(d)(1), and adding a new paragraph (e) to read as follows:
Sec. 94.105 Duty cycles.
* * * * *
(b) General cycle. Propulsion engines that are used with (or
intended to be
[[Page 68344]]
used with) fixed-pitch propellers, and any other engines for which the
other duty cycles of this section do not apply, shall be tested using
the duty cycle described in the following Table B-1:
* * * * *
(e) Recreational. For the purpose of determining compliance with
the emission standards of Sec. 94.8, recreational engines shall be
tested using the duty cycle described in Table B-5, which follows:
Table B-5.--Recreational Marine Duty Cycle
----------------------------------------------------------------------------------------------------------------
Engine
speed\(1)\ Percent of Minimum time
Mode No. (percent of maximum test in mode Weighting
maximum test power\(2)\ (minutes) factors
speed)
----------------------------------------------------------------------------------------------------------------
1............................................... 100 100 5.0 0.08
2............................................... 91 75 5.0 0.13
3............................................... 80 50 5.0 0.17
4............................................... 63 25 5.0 0.32
5............................................... idle 0 5.0 0.30
----------------------------------------------------------------------------------------------------------------
\1\ Engine speed: +/-2 percent of point.
\2\ Power: +/-2 percent of engine maximum value.
27. Section 94.106 is amended by revising paragraphs (b)
introductory text, (b)(1) introductory text, (b)(2) introductory text,
(b)(3) introductory text, and (b)(4) and adding a new paragraph (b)(5)
to read as follows:
Sec. 94.106 Supplemental test procedures.
* * * * *
(b) The specified Not to Exceed Zones for marine engines are
defined as follows. These Not to Exceed Zones apply, unless a modified
zone is established under paragraph (c) of this section.
(1) For commercial Category 1 engines certified using the duty
cycle specified in Sec. 94.105(b), the Not to Exceed zones are defined
as follows:
* * * * *
(2) For Category 2 engines certified using the duty cycle specified
in Sec. 94.105(b), the Not to Exceed zones are defined as follows:
* * * * *
(3) For engines certified using the duty cycle specified in Sec.
94.105(c)(2), the Not to Exceed zones are defined as follows:
* * * * *
(4) For engines certified using the duty cycle specified in Sec.
94.105(c)(1), the Not to Exceed zone is defined as any load greater
than or equal to 25 percent of maximum power at rated speed, and any
speed at which the engine operates in use.
(5) For recreational marine engines certified using the duty cycle
specified in Sec. 94.105(e), the Not to Exceed zones are defined as
follows:
(i) The Not to Exceed zone is the region between the curves power =
1.15 x SPD\2\ and power = 0.85 x SPD\4\, excluding all operation below
25% of maximum power at rated speed and excluding all operation below
63% of maximum test speed.
(ii) This zone is divided into three subzones, one below 45% of
maximum power at maximum test speed; one above 95% of maximum test
speed; and a third area including all of the remaining area of the NTE
zone.
(iii) SPD in paragraph (b)(5)(i) of this section refers to percent
of maximum test speed.
(iv) See Figure B-4 for an illustration of this Not to Exceed zone
as follows:
BILLING CODE 6560-50-P
[[Page 68345]]
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.003
BILLING CODE 6560-50-C
28. Section 94.108 is amended in paragraph (a)(1) by revising
footnote 1 in Table B-5 to read as follows:
Sec. 94.108 Test fuels.
(a) * * * (1) * * *
Table B-5.--Federal Test Fuel Specifications
------------------------------------------------------------------------
-------------------------------------------------------------------------
* * * * * * *
------------------------------------------------------------------------
\1\ All ASTM procedures in this table have been incorporated by
reference. See Sec. 94.5.
* * * * * * *
[[Page 68346]]
* * * * *
Subpart C--[Amended]
29. Section 94.203 is amended by revising paragraphs (d)(14) and
(d)(16) to read as follows:
Sec. 94.203 Application for certification.
* * * * *
(d) * * *
(14) A statement that all the engines included in the engine family
comply with the Not To Exceed standards specified in Sec. 94.8(e) when
operated under all conditions which may reasonably be expected to be
encountered in normal operation and use; the manufacturer also must
provide a detailed description of all testing, engineering analyses,
and other information which provides the basis for this statement.
* * * * *
(16) A statement indicating duty-cycle and application of the
engine (e.g., used to propel planing vessels, use to propel vessels
with variable-pitch propellers, constant-speed auxiliary, recreational,
etc.).
* * * * *
30. Section 94.204 is amended by removing ``and'' at the end of
paragraph (b)(9), adding ``; and'' at the end of paragraph (b)(10),
adding a new paragraph (b)(11), and revising paragraph (e) to read as
follows:
Sec. 94.204 Designation of engine families.
* * * * *
(b) * * *
(11) Class (commercial or recreational).
* * * * *
(e) Upon request by the manufacturer, the Administrator may allow
engines that would be required to be grouped into separate engine
families based on the criteria in paragraph (b) or (c) of this section
to be grouped into a single engine family if the manufacturer
demonstrates that the engines will have similar emission
characteristics; however, recreational and commercial engines may not
be grouped in the same engine family. This request must be accompanied
by emission information supporting the appropriateness of such combined
engine families.
31. Section 94.209 is revised to read as follows:
Sec. 94.209 Special provisions for post-manufacture marinizers and
small-volume manufacturers.
(a) Broader engine families. Instead of the requirements of Sec.
94.204, an engine family may consist of any engines subject to the same
emission standards. This does not change any of the requirements of
this part for showing that an engine family meets emission standards.
To be eligible to use the provisions of this paragraph (a), the
manufacturer must demonstrate one of the following:
(1) It is a post-manufacture marinizer and that the base engines
used for modification have a valid certificate of conformity issued
under 40 CFR part 89 or 40 CFR part 92 or the heavy-duty engine
provisions of 40 CFR part 86.
(2) It is a small-volume manufacturer.
(b) Hardship relief. Post-manufacture marinizers, small-volume
manufacturers, and small-volume boat builders may take any of the
otherwise prohibited actions identified in Sec. 94.1103(a)(1) if
approved in advance by the Administrator, subject to the following
requirements:
(1) Application for relief must be submitted to the Designated
Officer in writing prior to the earliest date in which the applying
manufacturer would be in violation of Sec. 94.1103. The manufacturer
must submit evidence showing that the requirements for approval have
been met.
(2) The conditions causing the impending violation must not be
substantially the fault of the applying manufacturer.
(3) The conditions causing the impending violation must jeopardize
the solvency of the applying manufacturer if relief is not granted.
(4) The applying manufacturer must demonstrate that no other
allowances under this part will be available to avoid the impending
violation.
(5) Any relief may not exceed one year beyond the date relief is
granted.
(6) The Administrator may impose other conditions on the granting
of relief including provisions to recover the lost environmental
benefit.
(7) The manufacturer must add a permanent, legible label, written
in block letters in English, to a readily visible part of each engine
exempted under this paragraph (b).
This label must include at least the following items:
(i) The label heading ``EMISSION CONTROL INFORMATION''.
(ii) Your corporate name and trademark.
(iii) Engine displacement (in liters), rated power, and model year
of the engine or whom to contact for further information.
(iv) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 94.209(b)
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
(c) Extension of deadlines. Small-volume manufacturers may use the
provisions of 40 CFR 1068.250 to ask for an extension of a deadline to
meet emission standards. We may require that you use available base
engines that have been certified to emission standards for land-based
engines until you are able to produce engines certified to the
requirements of this part.
32. Section 94.212 is amended by revising paragraph (b)(10) to read
as follows:
Sec. 94.212 Labeling.
* * * * *
(b) Engine labels. * * *
(10) The application for which the engine family is certified. (For
example: constant-speed auxiliary, variable-speed propulsion engines
used with fixed-pitch propellers, recreational, etc.)
* * * * *
33. Section 94.218 is amended by adding a new paragraph (d)(2)(iv)
to read as follows:
Sec. 94.218 Deterioration factor determination.
* * * * *
(d) * * *
(2) * * *
(iv) Assigned deterioration factors. Small-volume manufacturers may
use deterioration factors established by EPA.
Subpart D--[Amended]
34. Section 94.304 is amended by revising paragraph (k) to read as
follows:
Sec. 94.304 Compliance requirements.
* * * * *
(k) The following provisions limit credit exchanges between
different types of engines:
(1) Credits generated by Category 1 engine families may be used for
compliance by Category 1 or Category 2 engine families. Credits
generated from Category 1 engine families for use by Category 2 engine
families must be discounted by 25 percent.
(2) Credits generated by Category 2 engine families may be used for
compliance only by Category 2 engine families.
(3) Credits may not be exchanged between recreational and
commercial engines.
* * * * *
Subpart F--[Amended]
35. Section 94.501 is amended by revising paragraph (a) to read as
follows:
Sec. 94.501 Applicability.
(a) The requirements of this subpart are applicable to
manufacturers of engines subject to the provisions of
[[Page 68347]]
Subpart A of this part, excluding small-volume manufacturers.
* * * * *
36. Section 94.503 is amended by adding a new paragraph (d) to read
as follows:
Sec. 94.503 General requirements.
* * * * *
(d) If you certify an engine family with carryover emission data,
as described in Sec. 94.206(c), and these equivalent engine families
consistently pass the production-line testing requirements over the
preceding two-year period, you may ask for a reduced testing rate for
further production-line testing for that family. The minimum testing
rate is one engine per engine family. If we reduce your testing rate,
we may limit our approval to any number of model years. In determining
whether to approve your request, we may consider the number of engines
that have failed the emission tests.
Subpart J--[Amended]
37. Section 94.907 is amended by revising paragraphs (d) and (g) to
read as follows:
Sec. 94.907 Engine dressing exemption.
* * * * *
(d) New marine engines that meet all the following criteria are
exempt under this section:
(1) You must produce it by marinizing an engine covered by a valid
certificate of conformity from one of the following programs:
(i) Heavy-duty highway engines (40 CFR part 86).
(ii) Land-based nonroad diesel engines (40 CFR part 89).
(iii) Locomotive engines (40 CFR part 92).
(2) The engine must have the label required under 40 CFR part 86,
89, or 92.
(3) You must not make any changes to the certified engine that
could reasonably be expected to increase its emissions. For example, if
you make any of the following changes to one of these engines, you do
not qualify for the engine dressing exemption:
(i) Changing any fuel system parameters from the certified
configuration.
(ii) Replacing an original turbocharger, except that small-volume
manufacturers of recreational engines may replace an original
turbocharger with one that matches the performance of the original
turbocharger.
(iii) Modify or design the marine engine cooling or aftercooling
system so that temperatures or heat rejection rates are outside the
original engine manufacturer's specified ranges.
(4) You must make sure that fewer than 50 percent of the engine
model's total sales, from all companies, are used in marine
applications.
* * * * *
(g) If your engines do not meet the criteria listed in paragraphs
(d)(2) through (d)(4) of this section, they will be subject to the
standards and prohibitions of this part. Marinization without a valid
exemption or certificate of conformity would be a violation of Sec.
94.1103(a)(1) and/or the tampering prohibitions of the applicable land-
based regulations (40 CFR part 86, 89, or 92).
* * * * *
Subpart L--[Amended]
38. Section 94.1103 is amended by revising paragraph (a)(5) to read
as follows:
Sec. 94.1103 Prohibited acts.
(a) * * *
(5) For a manufacturer of marine vessels to distribute in commerce,
sell, offer for sale, or deliver for introduction into commerce a new
vessel containing an engine not covered by a certificate of conformity
applicable for an engine model year the same as or later than the
calendar year in which the manufacture of the new vessel is initiated.
This prohibition covers improper installation in a manner such that the
installed engine would not be covered by the engine manufacturer's
certificate. Improper installation would include, but is not limited
to, failure to follow the engine manufacturer's instructions related to
engine cooling, exhaust aftertreatment, emission sampling ports, or any
other emission-related component, parameter, or setting. In general,
you may use up your normal inventory of engines not certified to new
emission standards if they were built before the date of the new
standards. However, we consider stockpiling of these engines to be a
violation of paragraph (a)(1)(i)(A) of this section. (Note: For the
purpose of this paragraph (a)(5), the manufacture of a vessel is
initiated when the keel is laid, or the vessel is at a similar stage of
construction.)
* * * * *
39. A new subchapter U is added to chapter I, consisting of parts
1048, 1051, 1065, and 1068, to read as follows:
SUBCHAPTER U--AIR POLLUTION CONTROLS
PART 1048--CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-
IGNITION ENGINES
Subpart A--Determining How to Follow This Part
Sec.
1048.1 Does this part apply to me?
1048.5 Which engines are excluded or exempted from this part's
requirements?
1048.10 What main steps must I take to comply with this part?
1048.15 Do any other regulation parts affect me?
1048.20 What requirements from this part apply to my excluded
engines?
Subpart B--Emission Standards and Related Requirements
1048.101 What exhaust emission standards must my engines meet?
1048.105 What evaporative emissions standards and requirements
apply?
1048.110 How must my engines diagnose malfunctions?
1048.115 What other requirements must my engines meet?
1048.120 What warranty requirements apply to me?
1048.125 What maintenance instructions must I give to buyers?
1048.130 What installation instructions must I give to equipment
manufacturers?
1048.135 How must I label and identify the engines I produce?
1048.140 What are the provisions for certifying Blue Sky Series
engines?
1048.145 What provisions apply only for a limited time?
Subpart C--Certifying Engine Families
1048.201 What are the general requirements for submitting a
certification application?
1048.205 What must I include in my application?
1048.210 May I get preliminary approval before I complete my
application?
1048.215 What happens after I complete my application?
1048.220 How do I amend the maintenance instructions in my
application?
1048.225 How do I amend my application to include new or modified
engines?
1048.230 How do I select engine families?
1048.235 What emission testing must I perform for my application for
a certificate of conformity?
1048.240 How do I demonstrate that my engine family complies with
exhaust emission standards?
1048.245 How do I demonstrate that my engine family complies with
evaporative emission standards?
1048.250 What records must I keep and make available to EPA?
1048.255 When may EPA deny, revoke, or void my certificate of
conformity?
Subpart D--Testing Production-line Engines
1048.301 When must I test my production-line engines?
[[Page 68348]]
1048.305 How must I prepare and test my production-line engines?
1048.310 How must I select engines for production-line testing?
1048.315 How do I know when my engine family fails the production-
line testing requirements?
1048.320 What happens if one of my production-line engines fails to
meet emission standards?
1048.325 What happens if an engine family fails the production-line
requirements?
1048.330 May I sell engines from an engine family with a suspended
certificate of conformity?
1048.335 How do I ask EPA to reinstate my suspended certificate?
1048.340 When may EPA revoke my certificate under this subpart and
how may I sell these engines again?
1048.345 What production-line testing records must I send to EPA?
1048.350 What records must I keep?
Subpart E--Testing In-use Engines
1048.401 What testing requirements apply to my engines that have
gone into service?
1048.405 How does this program work?
1048.410 How must I select, prepare, and test my in-use engines?
1048.415 What happens if in-use engines do not meet requirements?
1048.420 What in-use testing information must I report to EPA?
1048.425 What records must I keep?
Subpart F--Test Procedures
1048.501 What procedures must I use to test my engines?
1048.505 What steady-state duty cycles apply for laboratory testing?
1048.510 What transient duty cycles apply for laboratory testing?
1048.515 Field-testing procedures.
Subpart G--Compliance Provisions
1048.601 What compliance provisions apply to these engines?
1048.605 What are the provisions for exempting engines from the
requirements of this part if they are already certified under the
motor-vehicle program?
1048.610 What are the provisions for producing nonroad equipment
with engines already certified under the motor-vehicle program?
1048.615 What are the provisions for exempting engines designed for
lawn and garden applications?
1048.620 What are the provisions for exempting large engines fueled
by natural gas?
1048.625 What special provisions apply to engines using
noncommercial fuels?
Subpart H--[Reserved]
Subpart I--Definitions and Other Reference Information
1048.801 What definitions apply to this part?
1048.805 What symbols, acronyms, and abbreviations does this part
use?
1048.810 What materials does this part reference?
1048.815 How should I request EPA to keep my information
confidential?
1048.820 How do I request a hearing?
Appendix I to Part 1048--Large Spark-ignition (SI) Transient Cycle
for Constant-Speed Engines
Appendix II to Part 1048--Large Spark-ignition (SI) Composite
Transient Cycle
Authority: 42 U.S.C. 7401-7671(q).
Subpart A--Determining How to Follow This Part
Sec. 1048.1 Does this part apply to me?
(a) This part applies to you if you manufacture or import new,
spark-ignition, nonroad engines (defined in Sec. 1048.801) with
maximum brake power above 19 kW, unless we exclude them under Sec.
1048.5. See Sec. 1048.20 for the requirements that apply to excluded
engines.
(b) If you manufacture or import engines with maximum brake power
at or below 19 kW that would otherwise be covered by 40 CFR part 90,
you may choose to meet the requirements of this part instead. In this
case, all the provisions of this part apply for those engines.
(c) As noted in subpart G of this part, 40 CFR part 1068 applies to
everyone, including anyone who manufactures, installs, owns, operates,
or rebuilds any of the engines this part covers or equipment containing
these engines.
(d) You need not follow this part for engines you produce before
January 1, 2004, unless you certify voluntarily. See Sec. Sec.
1048.101 through 1048.115 and Sec. 1048.145 and the definition of
model year in Sec. 1048.801 for more information about the timing of
new requirements.
(e) See Sec. Sec. 1048.801 and 1048.805 for definitions and
acronyms that apply to this part. The definition section contains
significant regulatory provisions and it is very important that you
read them.
Sec. 1048.5 Which engines are excluded or exempted from this part's
requirements?
(a) This part does not apply to the following nonroad engines:
(1) Engines certified to meet the requirements of 40 CFR part 1051
(for
example, engines used in snowmobiles and all-terrain vehicles).
(2) Propulsion marine engines. See 40 CFR part 91. This part
applies with respect to auxiliary marine engines.
(b) See subpart G of this part and 40 CFR part 1068, subpart C, for
exemptions of specific engines.
(c) Send the Designated Officer a written request if you want us to
determine whether this part covers or excludes certain engines.
Excluding engines from this part's requirements does not affect other
requirements that may apply to them.
Note: See 40 CFR part 87 for engines used in aircraft.)
(d) As defined in Sec. 1048.801, stationary engines are not
required to comply with this part (because they are not nonroad
engines), except that you must meet the requirements in Sec. 1048.20.
In addition, the prohibitions in 40 CFR 1068.101 restrict the use of
stationary engines for non-stationary purposes.
Sec. 1048.10 What main steps must I take to comply with this part?
(a) You must have a certificate of conformity from us for each
engine family before you do any of the following with a new nonroad
engine covered by this part: sell, offer for sale, introduce into
commerce, distribute or deliver for introduction into commerce, or
import it into the United States. ``New'' engines may include some
already placed in service (see the definition of ``new nonroad engine''
and ``new nonroad equipment'' in Sec. 1048.801). You must get a new
certificate of conformity for each new model year.
(b) To get a certificate of conformity and comply with its terms,
you must do six things:
(1) Meet the emission standards and other requirements in subpart B
of this part.
(2) Perform preproduction emission tests.
(3) Apply for certification (see subpart C of this part).
(4) Do routine emission testing on production engines as required
by subpart D of this part.
(5) Do emission testing on in-use engines, as we direct under
subpart E
of this part.
(6) Follow our instructions throughout this part.
(c) Subpart F of this part describes how to test your engines
(including references to other parts).
(d) Subpart G of this part and 40 CFR part 1068 describe
requirements and prohibitions that apply to engine manufacturers,
equipment manufacturers, owners, operators, rebuilders, and all others.
Sec. 1048.15 Do any other regulation parts affect me?
(a) Part 1065 of this chapter describes procedures and equipment
specifications for testing engines. Subpart F of this part describes
how to apply the provisions of part 1065 of this chapter to show you
meet the emission standards in this part.
[[Page 68349]]
(b) Part 1068 of this chapter describes general provisions,
including these seven areas:
(1) Prohibited acts and penalties for engine manufacturers,
equipment
manufacturers, and others.
(2) Rebuilding and other aftermarket changes.
(3) Exclusions and exemption for certain engines.
(4) Importing engines.
(5) Selective enforcement audits of your production.
(6) Defect reporting and recall.
(7) Procedures for hearings.
(c) Other parts of this chapter affect you if referenced in this
part.
Sec. 1048.20 What requirements from this part apply to my excluded
engines?
(a) Engine manufacturers producing an engine excluded under Sec.
1048.5(d) must add a permanent label or tag identifying each engine.
This applies equally to importers. To meet labeling requirements, you
must do the following things:
(1) Attach the label or tag in one piece so no one can remove it
without destroying or defacing it.
(2) Make sure it is durable and readable for the engine's entire
life.
(3) Secure it to a part of the engine needed for normal operation
and not normally requiring replacement.
(4) Write it in block letters in English.
(5) Instruct equipment manufacturers that they must place a
duplicate label as described in 40 CFR 1068.105 if they obscure the
engine's label.
(b) Engine labels or tags required under this section must have the
following information:
(1) Include the heading ``Emission Control Information''.
(2) Include your full corporate name and trademark.
(3) State the engine displacement (in liters) and maximum brake
power.
(4) State: ``THIS ENGINE IS EXCLUDED FROM THE REQUIREMENTS OF 40
CFR PART 1048 AS A ``STATIONARY ENGINE.'' INSTALLING OR USING THIS
ENGINE IN ANY OTHER APPLICATION MAY BE A VIOLATION OF FEDERAL LAW
SUBJECT TO CIVIL PENALTY.''.
Subpart B--Emission Standards and Related Requirements
Sec. 1048.101 What exhaust emission standards must my engines meet?
Apply the exhaust emission standards in this section by model year.
You may choose to certify engines earlier than we require. The Tier 1
standards apply only to steady-state testing, as described in paragraph
(b) of this section. The Tier 2 standards apply to steady-state,
transient, and field testing, as described in paragraphs (a), (b), and
(c) of this section.
(a) Standards for transient testing. Starting in the 2007 model
year, Tier 2 exhaust emission standards apply for transient measurement
of emissions with the duty-cycle test procedures in subpart F of this
part:
(1) The Tier 2 HC+NOX standard is 2.7 g/kW-hr and the
Tier 2 CO standard is 4.4 g/kW-hr. For severe-duty engines, the Tier 2
HC+NOX standard is 2.7 g/kW-hr and the Tier 2 CO standard is
130.0 g/kW-hr. The standards in this paragraph (a) do not apply for
transient testing of high-load engines.
(2) You may optionally certify your engines according to the
following formula instead of the standards in paragraph (a)(1) of this
section: (HC+NOX) x CO \0.784\ <= 8.57. The
HC+NOX and CO emission levels you select to satisfy this
formula, rounded to the nearest 0.1 g/kW-hr, become the emission
standards that apply for those engines. You may not select an
HC+NOX emission standard higher than 2.7 g/kW-hr or a CO
emission standard higher than 20.6 g/kW-hr. The following table
illustrates a range of possible values under this paragraph (a)(2):
Table 1 of Sec. 1048.101.--Examples of Possible Tier 2 Duty-cycle
Emission Standards
------------------------------------------------------------------------
CO (g/kW-
HC+NOX (g/kW-hr) hr)
------------------------------------------------------------------------
2.7........................................................ 4.4
2.2........................................................ 5.6
1.7........................................................ 7.9
1.3........................................................ 11.1
1.0........................................................ 15.5
0.8........................................................ 20.6
------------------------------------------------------------------------
(b) Standards for steady-state testing. Except as we allow in
paragraph (d) of this section, the following exhaust emission standards
apply for steady-state measurement of emissions with the duty-cycle
test procedures in subpart F of this part:
(1) The following table shows the Tier 1 exhaust emission standards
that apply to engines from 2004 through 2006 model years:
Table 2 of Sec. 1048.101.--Tier 1 Emission Standards (g/kW-hr)
----------------------------------------------------------------------------------------------------------------
General emission Alternate emission
standards standards for severe-
Testing -------------------------- duty engines
-------------------------
HC+NOX CO HC+NOX CO
----------------------------------------------------------------------------------------------------------------
Certification and production-line testing................... 4.0 50.0 4.0 130.0
In-use testing.............................................. 5.4 50.0 5.4 130.0
----------------------------------------------------------------------------------------------------------------
(2) Starting in the 2007 model year, engines must meet the Tier 2
exhaust emission standards in paragraph (a) of this section for both
steady-state and transient testing. See paragraph (d) of this section
for alternate standards that apply for certain engines.
(c) Standards for field testing. Starting in 2007, the following
Tier 2 exhaust emission standards apply for emission measurements with
the field-testing procedures in subpart F of this part:
(1) The HC+NOX standard is 3.8 g/kW-hr and the CO
standard is 6.5 g/kW-hr. For severe-duty engines, the HC+NOX
standard is 3.8 g/kW-hr and the CO standard is 200.0 g/kW-hr. For
natural gas-fueled engines, you are not required to measure nonmethane
hydrocarbon emissions or total hydrocarbon emissions for testing to
show that the engine meets the emission standards of this paragraph
(c); that is, you may assume HC emissions are equal to zero.
(2) You may apply the following formula to determine alternate
emission standards that apply to your engines instead of the standards
in paragraph (c)(1) of this section: (HC+NOX) x CO\0.791\ <=
16.78. HC+NOX emission levels may not exceed 3.8 g/kW-hr and
CO emission levels may not exceed 31.0 g/kW-hr. The following table
illustrates a range of possible values under this paragraph (c)(2):
[[Page 68350]]
Table 3 of Sec. 1048.101.--Examples of Possible Tier 2 Field-testing
Emission Standards
------------------------------------------------------------------------
CO (g/kW-
HC+NOX (g/kW-hr) hr)
------------------------------------------------------------------------
3.8........................................................ 6.5
3.1........................................................ 8.5
2.4........................................................ 11.7
1.8........................................................ 16.8
1.4........................................................ 23.1
1.1........................................................ 31.0
------------------------------------------------------------------------
(d) Engine protection. For engines that require enrichment at high
loads to protect the engine, you may ask to meet alternate Tier 2
standards of 2.7 g/kW-hr for HC+NOX and 31.0 g/kW-hr for CO
instead of the emission standards described in paragraph (b)(2) of this
section for steady-state testing. If we approve your request, you must
still meet the transient testing standards in paragraph (a) of this
section and the field-testing standards in paragraph (c) of this
section. To qualify for this allowance, you must do all the following
things:
(1) Show that enrichment is necessary to protect the engine from
damage.
(2) Show that you limit enrichment to operating modes that require
additional cooling to protect the engine from damage.
(3) Show in your application for certification that enrichment will
rarely occur in use in the equipment in which your engines are
installed. For example, an engine that is expected to operate 5 percent
of the time in use with enrichment would clearly not qualify.
(4) Include in your installation instructions any steps necessary
for someone installing your engines to prevent enrichment during normal
operation (see Sec. 1048.130).
(e) Fuel types. Apply the exhaust emission standards in this
section for engines using each type of fuel specified in 40 CFR part
1065, subpart C, for which they are designed to operate. You must meet
the numerical emission standards for hydrocarbons in this section based
on the following types of hydrocarbon emissions for engines powered by
the following fuels:
(1) Gasoline- and LPG-fueled engines: THC emissions.
(2) Natural gas-fueled engines: NMHC emissions.
(3) Alcohol-fueled engines: THCE emissions.
(f) Small engines. Certain engines with total displacement at or
below 1000 cc may comply with the requirements of 40 CFR part 90
instead of complying with the requirements of this part, as described
in Sec. 1048.615.
(g) Useful life. Your engines must meet the exhaust emission
standards in paragraphs (a) through (c) of this section over their full
useful life (Sec. 1048.240 describes how to use deterioration factors
to show this). The minimum useful life is 5,000 hours of operation or
seven years, whichever comes first.
(1) Specify a longer useful life in hours for an engine family
under either of two conditions:
(i) If you design, advertise, or market your engine to operate
longer than the minimum useful life (your recommended hours until
rebuild may indicate a longer design life).
(ii) If your basic mechanical warranty is longer than the minimum
useful life.
(2) You may request a shorter useful life for an engine family if
you have documentation from in-use engines showing that these engines
will rarely operate longer than the alternate useful life. The useful
life value may not be shorter than any of the following:
(i) 1,000 hours of operation.
(ii) Your recommended overhaul interval.
(iii) Your mechanical warranty for the engine.
(h) Applicability for testing. The standards in this subpart apply
to all testing, including production-line and in-use testing, as
described in subparts D and E of this part.
Sec. 1048.105 What evaporative emissions standards and requirements
apply?
(a) Starting in the 2007 model year, engines that run on a volatile
liquid fuel (such as gasoline), must meet the following evaporative
emissions standards and requirements:
(1) Evaporative hydrocarbon emissions may not exceed 0.2 grams per
gallon of fuel tank capacity when measured with the test procedures for
evaporative emissions in subpart F of this part.
(2) For nonmetallic fuel lines, you must specify and use products
that meet the Category 1 specifications in SAE J2260 (incorporated by
reference in Sec. 1048.810).
(3) Liquid fuel in the fuel tank may not reach boiling during
continuous engine operation in the final installation at an ambient
temperature of 30[deg]
C. Note that gasoline with a Reid vapor pressure
of 62 kPa (9 psi) begins to boil at about 53[deg]
C.
(b) Note that Sec. 1048.245 allows you to use design-based
certification instead of generating new emission data.
(c) If other companies install your engines in their equipment,
give them any appropriate instructions, as described in Sec. 1048.130.
Sec. 1048.110 How must my engines diagnose malfunctions?
(a) Equip your engines with a diagnostic system. Starting in the
2007 model year, equip each engine with a diagnostic system that will
detect significant malfunctions in its emission-control system using
one of the following protocols:
(1) If your emission-control strategy depends on maintaining air-
fuel ratios at stoichiometry, an acceptable diagnostic design would
identify malfunction whenever the air-fuel ratio does not cross
stoichiometry for one minute of intended closed-loop operation. You may
use other diagnostic strategies if we approve them in advance.
(2) If the protocol described in paragraph (a)(1) of this section
does not apply to your engine, you must use an alternative approach
that we approve in advance. Your alternative approach must generally
detect when the emission-control system is not functioning properly.
(b) Use a malfunction-indicator light (MIL). The MIL must be
readily visible to the operator; it may be any color except red. When
the MIL goes on, it must display ``Check Engine,'' ``Service Engine
Soon,'' or a similar message that we approve. You may use sound in
addition to the light signal. The MIL must go on under each of these
circumstances:
(1) When a malfunction occurs, as described in paragraph (a) of
this section.
(2) When the diagnostic system cannot send signals to meet the
requirement of paragraph (b)(1) of this section.
(3) When the engine's ignition is in the ``key-on'' position before
starting or cranking. The MIL should go out after engine starting if
the system detects no malfunction.
(c) Control when the MIL can go out. If the MIL goes on to show a
malfunction, it must remain on during all later engine operation until
servicing corrects the malfunction. If the engine is not serviced, but
the malfunction does not recur for three consecutive engine starts
during which the malfunctioning system is evaluated and found to be
working properly, the MIL may stay off during later engine operation.
(d) Store trouble codes in computer memory. Record and store in
computer memory any diagnostic trouble codes showing a malfunction that
should illuminate the MIL. The stored codes must identify the
malfunctioning system or component as uniquely as possible. Make these
codes available through the data link connector as described in
[[Page 68351]]
paragraph (g) of this section. You may store codes for conditions that
do not turn on the MIL. The system must store a separate code to show
when the diagnostic system is disabled (from malfunction or tampering).
(e) Make data, access codes, and devices accessible. Make all
required data accessible to us without any access codes or devices that
only you can supply. Ensure that anyone servicing your engine can read
and understand the diagnostic trouble codes stored in the onboard
computer with generic tools and information.
(f) Consider exceptions for certain conditions. Your diagnostic
systems may disregard trouble codes for the first three minutes after
engine starting. You may ask us to approve diagnostic-system designs
that disregard trouble codes under other conditions that would produce
an unreliable reading, damage systems or components, or cause other
safety risks. This might include operation at altitudes over 8,000
feet.
(g) Follow standard references for formats, codes, and connections.
Follow conventions defined in the following documents (incorporated by
reference in Sec. 1048.810) or ask us to approve using updated
versions of (or variations from) these documents:
(1) ISO 9141-2 Road vehicles-Diagnostic systems--Part 2: CARB
requirements for interchange of digital information, February 1994.
(2) ISO 14230-4 Road vehicles--Diagnostic systems--Keyword Protocol
2000--Part 4: Requirements for emission-related systems, June 2000.
Sec. 1048.115 What other requirements must my engines meet?
Your engines must meet the following requirements:
(a) Closed crankcase. Your engines may not vent crankcase emissions
into the atmosphere throughout their useful life, with the following
exception: your engines may vent crankcase emissions if you measure and
include these crankcase emissions with all measured exhaust emissions.
(b) Torque broadcasting. Electronically controlled engines must
broadcast their speed and output shaft torque (in newton-meters) on
their controller area networks. Engines may alternatively broadcast a
surrogate value for torque that can be read with a remote device. This
information is necessary for testing engines in the field (see 40 CFR
1065.515). This requirement applies beginning in the 2007 model year.
Small-volume engine manufacturers may omit this requirement.
(c) EPA access to broadcast information. If we request it, you must
provide us any hardware or tools we would need to readily read,
interpret, and record all information broadcast by an engine's on-board
computers and electronic control modules. If you broadcast a surrogate
parameter for torque values, you must provide us what we need to
convert these into torque units. We will not ask for hardware or tools
if they are readily available commercially.
(d) Emission sampling capability. Produce all your engines to allow
sampling of exhaust emissions in the field without damaging the engine
or equipment. Show in your application for certification how this can
be done in a way that prevents diluting the exhaust sample with ambient
air. To do this, you might simply allow for extending the exhaust pipe
by 20 cm; you might also install exhaust ports downstream of any
aftertreatment devices.
(e) Adjustable parameters. Engines that have adjustable parameters
must meet all the requirements of this part for any adjustment in the
physically adjustable range.
(1) We do not consider an operating parameter adjustable if you
permanently seal it or if ordinary tools cannot readily access it.
(2) We may require that you set adjustable parameters to any
specification within the adjustable range during certification testing,
production-line testing, selective enforcement auditing, or any in-use
testing.
(f) Prohibited controls. You may not design your engines with
emission-control devices, systems, or elements of design that cause or
contribute to an unreasonable risk to public health, welfare, or safety
while operating. For example, this would apply if the engine emits a
noxious or toxic substance it would otherwise not emit that contributes
to such an unreasonable risk.
(g) Defeat devices. You may not equip your engines with a defeat
device. A defeat device is an auxiliary emission-control device that
reduces the effectiveness of emission controls under conditions you may
reasonably expect the engine to encounter during normal operation and
use. This does not apply to auxiliary emission-control devices you
identify in your certification application if any of the following is
true:
(1) The conditions of concern were substantially included in your
prescribed duty cycles.
(2) You show your design is necessary to prevent catastrophic
engine (or equipment) damage or accidents.
(3) The reduced effectiveness applies only to starting the engine.
Sec. 1048.120 What warranty requirements apply to me?
(a) General requirements. You must warrant to the ultimate buyer
that the new nonroad engine meets two conditions:
(1) It is designed, built, and equipped it to conform at the time
of sale with the requirements of this part.
(2) It is free from defects in materials and workmanship that may
keep it from meeting these requirements.
(b) Warranty period. Your emission-related warranty must be valid
for at least 50 percent of the engine's useful life in hours of
operation or at least three years, whichever comes first. In the case
of a high-cost warranted part, the warranty must be valid for at least
70 percent of the engine's useful life in hours of operation or at
least five years, whichever comes first. You may offer an emission-
related warranty more generous than we require. This warranty may not
be shorter than any published or negotiated warranty you offer for the
engine or any of its components. If an engine has no hour meter, we
base the warranty periods in this paragraph (b) only on the engine's
age (in years).
(c) Components covered. The emission-related warranty must cover
components whose failure would increase an engine's emissions,
including electronic controls, fuel injection (for liquid or gaseous
fuels), exhaust-gas recirculation, aftertreatment, or any other system
you develop to control emissions. We generally consider replacing or
repairing other components to be the owner's responsibility.
(d) Scheduled maintenance. You may schedule emission-related
maintenance for a component named in paragraph (c) of this section,
subject to the restrictions of Sec. 1048.125. You are not required to
cover this scheduled maintenance under your warranty if the component
meets either of the following criteria:
(1) The component was in general use on similar engines, and was
subject to scheduled maintenance, before January 1, 2000.
(2) Failure of the component would clearly degrade the engine's
performance enough that the operator would need to repair or replace
it.
(e) Limited applicability. You may deny warranty claims under this
section if the operator caused the problem, as described in 40 CFR
1068.115.
(f) Aftermarket parts. As noted 40 CFR 1068.101, it is a violation
of the Act to manufacture an engine part if one of its main effects is
to reduce the
[[Page 68352]]
effectiveness of the engine's emission controls. If you make an
aftermarket part, you may--but do not have to--certify that using the
part will still allow engines to meet emission standards, as described
in 40 CFR 85.2114.
Sec. 1048.125 What maintenance instructions must I give to buyers?
Give the ultimate buyer of each new nonroad engine written
instructions for properly maintaining and using the engine, including
the emission-control system. The maintenance instructions also apply to
service accumulation on your test engines, as described in 40 CFR part
1065, subpart E.
(a) Critical emission-related maintenance. Critical emission-
related maintenance includes any adjustment, cleaning, repair, or
replacement of air-induction, fuel-system, or ignition components,
aftertreatment devices, exhaust gas recirculation systems, crankcase
ventilation valves, sensors, or electronic control units. This may also
include any other component whose only purpose is to reduce emissions
or whose failure will increase emissions without significantly
degrading engine performance. You may schedule critical emission-
related maintenance on these components if you meet the following
conditions:
(1) You may ask us to approve critical emission-related maintenance
only if it meets two criteria:
(i) Operators are reasonably likely to do the maintenance you call
for.
(ii) Engines need the maintenance to meet emission standards.
(2) We will accept scheduled maintenance as reasonably likely to
occur in use if you satisfy any of four conditions:
(i) You present data showing that, if a lack of maintenance
increases emissions, it also unacceptably degrades the engine's
performance.
(ii) You present survey data showing that 80 percent of engines in
the field get the maintenance you specify at the recommended intervals.
(iii) You provide the maintenance free of charge and clearly say so
in maintenance instructions for the customer.
(iv) You otherwise show us that the maintenance is reasonably
likely to be done at the recommended intervals.
(3) You may not schedule critical emission-related maintenance more
frequently than the following intervals, except as specified in
paragraph (a)(4) of this section:
(i) For catalysts, fuel injectors, electronic control units,
superchargers, and turbochargers: the useful life of the engine family.
(ii) For gaseous fuel-system components (cleaning without
disassembly only) and oxygen sensors: 2,500 hours.
(4) If your engine family has an alternate useful life shorter than
the period specified in paragraph (a)(3)(ii) of this section, you may
not schedule maintenance on those components more frequently than the
alternate useful life (see Sec. 1048.101(g)).
(b) Recommended additional maintenance. You may recommend any
additional amount of maintenance on the components listed in paragraph
(a) of this section, as long as you make clear that these maintenance
steps are not necessary to keep the emission-related warranty valid. If
operators do the maintenance specified in paragraph (a) of this
section, but not the recommended additional maintenance, this does not
allow you to disqualify them from in-use testing or deny a warranty
claim.
(c) Special maintenance. You may specify more frequent maintenance
to address problems related to special situations such as substandard
fuel or atypical engine operation. For example, you may specify more
frequent cleaning of fuel system components for engines you have reason
to believe will be using fuel that causes substantially more engine
performance problems than commercial fuels of the same type that are
generally available across the United States.
(d) Noncritical emission-related maintenance. For engine parts not
listed in paragraph (a) of this section, you may schedule any amount of
emission-related inspection or maintenance. But you must state clearly
that these steps are not necessary to keep the emission-related
warranty valid. Also, do not take these inspection or maintenance steps
during service accumulation on your test engines.
(e) Maintenance that is not emission-related. For maintenance
unrelated to emission controls, you may schedule any amount of
inspection or maintenance. You may also take these inspection or
maintenance steps during service accumulation on your test vehicles or
engines. This might include adding engine oil or changing air, fuel, or
oil filters.
(f) Source of parts and repairs. Print clearly on the first page of
your written maintenance instructions that any repair shop or person
may maintain, replace, or repair emission-control devices and systems.
Your instructions may not require components or service identified by
brand, trade, or corporate name. Also, do not directly or indirectly
condition your warranty on a requirement that the vehicle be serviced
by your franchised dealers or any other service establishments with
which you have a commercial relationship. You may disregard the
requirements in this paragraph (f) if you do one of two things:
(1) Provide a component or service without charge under the
purchase agreement.
(2) Get us to waive this prohibition in the public's interest by
convincing us the engine will work properly only with the identified
component or service.
Sec. 1048.130 What installation instructions must I give to equipment
manufacturers?
(a) If you sell an engine for someone else to install in a piece of
nonroad equipment, give the buyer of the engine written instructions
for installing it consistent with the requirements of this part.
Include all information necessary to ensure that engines installed this
way will meet emission standards.
(b) Make sure these instructions have the following information:
(1) Include the heading: ``Emission-related installation
instructions''.
(2) State: ``Failing to follow these instructions when installing a
certified engine in a piece of nonroad equipment violates federal law
(40 CFR 1068.105(b)), subject to fines or other penalties as described
in the Clean Air Act.''.
(3) Describe any other instructions needed to install an exhaust
aftertreatment device and to locate exhaust sampling ports consistent
with your application for certification.
(4) Describe the steps needed to control evaporative emissions, as
described in Sec. Sec. 1048.105 and 1048.245.
(5) Describe any necessary steps for installing the diagnostic
system described in Sec. 1048.110.
(6) Describe any limits on the range of applications needed to
ensure that the engine operates consistently with your application for
certification. For example, if your engines are certified only for
constant-speed operation, tell equipment manufacturers not to install
the engines in variable-speed applications. Also, if you need to avoid
sustained high-load operation to meet the field-testing emission
standards we specify in Sec. 1048.101(c) or to comply with the
provisions of Sec. 1048.101(d), describe how the equipment
manufacturer must properly size the engines for a given application.
(7) Describe any other instructions to make sure the installed
engine will operate according to design specifications in your
application for certification.
(8) State: ``If you install the engine in a way that makes the
engine's emission
[[Page 68353]]
control information label hard to read during normal engine
maintenance, you must place a duplicate label on the vehicle, as
described in 40 CFR 1068.105.''.
(c) You do not need installation instructions for engines you
install in your own equipment.
Sec. 1048.135 How must I label and identify the engines I produce?
(a) Assign each production engine a unique identification number
and permanently and legibly affix, engrave, or stamp it on the engine.
(b) At the time of manufacture, add a permanent emission control
information label identifying each engine. To meet labeling
requirements, do four things:
(1) Attach the label in one piece so it is not removable without
being destroyed or defaced.
(2) Design and produce it to be durable and readable for the
engine's entire life.
(3) Secure it to a part of the engine needed for normal operation
and not normally requiring replacement.
(4) Write it in block letters in English.
(c) On your engine's emission control information label, do 13
things:
(1) Include the heading ``EMISSION CONTROL INFORMATION''.
(2) Include your full corporate name and trademark.
(3) State: ``THIS ENGINE IS CERTIFIED TO OPERATE ON [specify
operating fuel or fuels].''.
(4) Identify the emission-control system; your identifiers must use
names and abbreviations consistent with SAE J1930 (incorporated by
reference in Sec. 1048.810).
(5) List all requirements for fuel and lubricants.
(6) State the date of manufacture (DAY (optional), MONTH, and
YEAR); if you stamp this information on the engine and print it in the
owner's manual, you may omit it from the emission control information
label.
(7) State: ``THIS ENGINE MEETS U.S. ENVIRONMENTAL PROTECTION AGENCY
REGULATIONS FOR (MODEL YEAR) LARGE NONROAD SI ENGINES.''.
(8) Include EPA's standardized designation for the engine family
(and subfamily, where applicable).
(9) State the engine's displacement (in liters) and maximum brake
power.
(10) State the engine's useful life (see Sec. 1048.101(g)).
(11) List specifications and adjustments for engine tuneups; show
the proper position for the transmission during tuneup and state which
accessories should be operating.
(12) Describe other information on proper maintenance and use.
(13) Identify the emission standards to which you have certified
the engine.
(d) Some of your engines may need more information on the emission
control information label.
(1) If you have an engine family that has been certified only for
constant-speed engines, add to the engine label ``CONSTANT-SPEED
ONLY''.
(2) If you have an engine family that has been certified only for
variable-speed engines, add to the engine label ``VARIABLE-SPEED
ONLY''.
(3) If you have an engine family that has been certified only for
high-load engines, add to the engine label ``THIS ENGINE IS NOT
INTENDED FOR OPERATION AT LESS THAN 75 PERCENT OF FULL LOAD.''.
(4) If you certify an engine to the voluntary standards in Sec.
1048.140, add to the engine label ``BLUE SKY SERIES''.
(5) If you produce an engine we exempt from the requirements of
this part, see subpart G of this part and 40 CFR part 1068, subparts C
and D, for more label information.
(6) If you certify an engine family under Sec. 1048.101(d) (and
show in your application for certification that in-use engines will
experience infrequent high-load operation), add to the engine label
``THIS ENGINE IS NOT INTENDED FOR OPERATION AT MORE THAN -- PERCENT OF
FULL LOAD.''. Specify the appropriate percentage of full load based on
the nature of the engine protection. You may add other statements to
discourage operation in engine-protection modes.
(e) Some engines may not have enough space for an emission control
information label with all the required information. In this case, you
may omit the information required in paragraphs (c)(3), (c)(4), (c)(5),
and (c)(12) of this section if you print it in the owner's manual
instead.
(f) If you are unable to meet these labeling requirements, you may
ask us to modify them consistent with the intent of this section.
Sec. 1048.140 What are the provisions for certifying Blue Sky Series
engines?
This section defines voluntary standards for a recognized level of
superior emission control for engines designated as ``Blue Sky Series''
engines. Blue Sky Series engines must meet one of the following
standards:
(a) For the 2003 model year, to receive a certificate of
conformity, a ``Blue Sky Series'' engine family must meet all the
requirements in this part that apply to 2004 model year engines. This
includes all testing and reporting requirements.
(b) For the 2003 through 2006 model years, to receive a certificate
of conformity, a ``Blue Sky Series'' engine family must meet all the
requirements in this part that apply to 2007 model year engines. This
includes all testing and reporting requirements.
(c) For any model year, to receive a certificate of conformity as a
``Blue Sky Series'' engine family must meet all the requirements in
this part, while certifying to the following exhaust emission
standards:
(1) 0.8 g/kW-hr HC+NOX and 4.4 g/kW-hr CO using steady-
state and transient test procedures, as described in subpart F of this
part.
(2) 1.1 g/kW-hr HC+NOX and 6.6 g/kW-hr CO using field-
testing procedures, as described in subpart F of this part.
(d) If you certify an engine family under this section, it is
subject to all the requirements of this part as if these voluntary
standards were mandatory.
Sec. 1048.145 What provisions apply only for a limited time?
The provisions in this section apply instead of other provisions in
this part. This section describes when these interim provisions expire.
(a) Family banking. You may certify an engine family to comply with
Tier 1 or Tier 2 standards earlier than necessary. For each model year
of early compliance for an engine family, you may delay compliance with
the same standards for an equal number of engines from another engine
family (or families) for one model year. If you certify engines under
the voluntary standards of Sec. 1048.140, you may not use them in your
calculation under this paragraph (a). Base your calculation on actual
power-weighted nationwide sales for each family. You may delay
compliance for up to three model years. For example, if you sell 1,000
engines with an average power rating of 60 kW certified a year early,
you may delay certification to that tier of standards for up to 60,000
kW-engine-years in any of the following ways:
(1) Delay certification of another engine family with an average
power rating of 100 kW of up to 600 engines for one model year.
(2) Delay certification of another engine family with an average
power rating of 100 kW of up to 200 engines for three model years.
(3) Delay certification of one engine family with an average power
rating of 100 kW of up to 400 engines for one model year and a second
engine family with an average power rating of 200 kW of up to 50
engines for two model years.
(b) Hydrocarbon standards. For 2004 through 2006 model years,
engine manufacturers may use nonmethane
[[Page 68354]]
hydrocarbon measurements to demonstrate compliance with applicable
emission standards.
(c) Transient emission testing. Engines rated over 560 kW are
exempt from the transient emission standards in Sec. 1048.101(a).
(d) Tier 1 deterioration factors. For Tier 1 engines, base the
deterioration factor from Sec. 1048.240 on 3500 hours of operation. We
may assign a deterioration factor for a Tier 1 engine family, but this
would not affect your need to meet all emission standards that apply.
(e) [Reserved]
(f) Optional early field testing. You may optionally use the field-
testing procedures in subpart F of this part for any in-use testing
required under subpart E of this part to show that you meet Tier 1
standards. In this case, the same Tier 1 in-use emission standards
apply to both steady-state testing in the laboratory and field testing.
(g) Small-volume provisions. If you qualify for the hardship
provisions in Sec. 1068.250 of this chapter, we may approve extensions
of up to four years total.
(h) 2004 certification. For the 2004 model year, you may choose to
have the emission standards and other requirements that apply to these
engines in California serve as the emission standards and other
requirements applicable under this part, instead of those in subpart A
of this part. To ask for a certificate under this paragraph (h), send
us the application for certification that you prepare for the
California Air Resources Board instead of the information we otherwise
require in Sec. 1048.205.
(i) Recreational vehicles. Engines or vehicles identified in the
scope of 40 CFR part 1051 that are not yet regulated under that part
are excluded from the requirements of this part. For example,
snowmobiles produced in 2004 are not subject to the emission standards
in this part. Once emission standards apply to these engines and
vehicles, they are excluded from the requirements of this part under
Sec. 1048.5(a)(1).
Subpart C--Certifying Engine Families
Sec. 1048.201 What are the general requirements for submitting a
certification application?
(a) Send us an application for a certificate of conformity for each
engine family. Each application is valid for only one model year.
(b) The application must not include false or incomplete statements
or information (see Sec. 1048.255).
(c) We may choose to ask you to send us less information than we
specify in this subpart, but this would not change your recordkeeping
requirements.
(d) Use good engineering judgment for all decisions related to your
application (see 40 CFR 1068.5).
(e) An authorized representative of your company must approve and
sign the application.
Sec. 1048.205 What must I include in my application?
In your application, do all the following things unless we ask you
to send us less information:
(a) Describe the engine family's specifications and other basic
parameters of the engine's design. List the types of fuel you intend to
use to certify the engine family (for example, gasoline, liquefied
petroleum gas, methanol, or natural gas).
(b) Explain how the emission-control systems operate.
(1) Describe in detail all the system components for controlling
exhaust emissions, including auxiliary emission-control devices and all
fuel-system components you will install on any production or test
engine. Explain why any auxiliary emission-control devices are not
defeat devices (see Sec. 1048.115(g)). Do not include detailed
calibrations for components unless we ask for them.
(2) Describe the evaporative emission controls.
(c) Explain how the engine diagnostic system works, describing
especially the engine conditions (with the corresponding diagnostic
trouble codes) that cause the malfunction-indicator light to go on.
Propose what you consider to be extreme conditions under which the
diagnostic system should disregard trouble codes, as described in Sec.
1048.110.
(d) Describe the engines you selected for testing and the reasons
for selecting them.
(e) Describe any special or alternate test procedures you used (see
Sec. 1048.501).
(f) Describe how you operated the engine or vehicle prior to
testing, including the duty cycle and the number of engine operating
hours used to stabilize emission levels. Describe any scheduled
maintenance you did.
(g) List the specifications of the test fuel to show that it falls
within the required ranges we specify in 40 CFR part 1065, subpart C.
(h) Identify the engine family's useful life.
(i) Propose maintenance and use instructions for the ultimate buyer
of each new nonroad engine (see Sec. 1048.125).
(j) Propose emission-related installation instructions if you sell
engines for someone else to install in a piece of nonroad equipment
(see Sec. 1048.130).
(k) Identify each high-cost warranted part and show us how you
calculated its replacement cost, including the estimated retail cost of
the part, labor rates, and labor hours to diagnose and replace
defective parts.
(l) Propose an emission control information label.
(m) Present emission data to show that you meet emission standards.
(1) Present exhaust emission data for HC, NOX, and CO on
a test engine to show your engines meet the duty-cycle emission
standards we specify in Sec. 1048.101(a) and (b). Show these figures
before and after applying deterioration factors for each engine.
Starting in the 2007 model year, identify the duty-cycle emission
standards to which you are certifying engines in the engine family.
Include test data for each type of fuel from 40 CFR part 1065, subpart
C, on which you intend for engines in the engine family to operate (for
example, gasoline, liquefied petroleum gas, methanol, or natural gas).
If we specify more than one grade of any fuel type (for example, a
summer grade and winter grade of gasoline), you only need to submit
test data for one grade, unless the regulations of this part specify
otherwise for your engine. Note that Sec. 1048.235 allows you to
submit an application in certain cases without new emission data.
(2) If your engine family includes a volatile liquid fuel (and you
do not use design-based certification under Sec. 1048.245) present
evaporative test data to show your vehicles meet the evaporative
emission standards we specify in subpart B of this part. Show these
figures before and after applying deterioration factors, where
applicable.
(n) Report all test results, including those from invalid tests or
from any nonstandard tests (such as measurements based on exhaust
concentrations in parts per million).
(o) Identify the engine family's deterioration factors and describe
how you developed them. Present any emission test data you used for
this.
(p) Describe all adjustable operating parameters (see Sec.
1048.115(e)), including the following:
(1) The nominal or recommended setting.
(2) The intended physically adjustable range, including production
tolerances if they affect the range.
(3) The limits or stops used to establish adjustable ranges.
(q) Describe everything we need to read and interpret all the
information broadcast by an engine's onboard
[[Page 68355]]
computers and electronic control modules and state that you will give
us any hardware or tools we would need to do this. You may reference
any appropriate publicly released standards that define conventions for
these messages and parameters. Format your information consistent with
publicly released standards.
(r) State whether your engine will operate in variable-speed
applications, constant-speed applications, or both. If your
certification covers only constant-speed or only variable-speed
applications, describe how you will prevent use of these engines in the
applications for which they are not certified.
(s) Starting in the 2007 model year, state that all the engines in
the engine family comply with the field-testing emission standards we
specify in Sec. 1048.101(c) for all normal operation and use (see
Sec. 1048.515). Describe in detail any testing, engineering analysis,
or other information on which you base this statement.
(t) State that you operated your test engines according to the
specified procedures and test parameters using the fuels described in
the application to show you meet the requirements of this part.
(u) State unconditionally that all the engines in the engine family
comply with the requirements of this part, other referenced parts, and
the Clean Air Act.
(v) Include estimates of U.S.-directed production volumes.
(w) Show us how to modify your production engines to measure
emissions in the field (see Sec. 1048.115(d)).
(x) Add other information to help us evaluate your application if
we ask for it.
Sec. 1048.210 May I get preliminary approval before I complete my
application?
If you send us information before you finish the application, we
will review it and make any appropriate determinations listed in Sec.
1048.215(b)(1) through (7). Decisions made under this section are
considered to be preliminary approval. We will generally not disapprove
applications under Sec. 1048.215(b)(1) through (5) where we have given
you preliminary approval, unless we find new and substantial
information supporting a different decision.
(a) If you request preliminary approval related to the upcoming
model year or the model year after that, we will make a ``best-
efforts'' attempt to make the appropriate determinations as soon as
possible. We will generally not provide preliminary approval related to
a future model year more than two years ahead of time.
(b) You may consider full compliance with published guidance to be
preliminary approval only if the guidance includes a statement that we
intend you to consider it as such.
Sec. 1048.215 What happens after I complete my application?
(a) If any of the information in your application changes after you
submit it, amend it as described in Sec. 1048.225.
(b) We may deny your application (that is, determine that we cannot
approve it without revision) if the engine family does not meet the
requirements of this part or the Act. For example:
(1) If you inappropriately use the provisions of Sec. 1048.230(c)
or (d) to define a broader or narrower engine family, we will require
you to redefine your engine family.
(2) If we determine you did not appropriately select the useful
life under Sec. 1048.101(g), we will require you to lengthen it.
(3) If we determine you did not appropriately select deterioration
factors under Sec. 1048.240(c), we will require you to revise them.
(4) If your diagnostic system is inadequate for detecting
significant malfunctions in emission-control systems, as described in
Sec. 1048.110(b), we will require you to make the system more
effective.
(5) If your diagnostic system inappropriately disregards trouble
codes under certain conditions, as described in Sec. 1048.110(f), we
will require you to change the system to operate under broader
conditions.
(6) If your proposed emission control information label is
inconsistent with Sec. 1048.135, we will require you to change it (and
tell you how, if possible).
(7) If you require or recommend maintenance and use instructions
inconsistent with Sec. 1048.125, we will require you to change them.
(8) If we find any other problem with your application, we will
tell you what the problem is and what needs to be corrected.
(c) If we determine your application is complete and shows that the
engine family meets all the requirements of this part and the Act, we
will issue a certificate of conformity for your engine family for that
model year. If we deny the application, we will explain why in writing.
You may then ask us to hold a hearing to reconsider our decision (see
Sec. 1048.820).
Sec. 1048.220 How do I amend the maintenance instructions in my
application?
Send the Designated Officer a request to amend your application for
certification for an engine family if you want to change the emission-
related maintenance instructions in a way that could affect emissions.
In your request, describe the proposed changes to the maintenance
instructions.
(a) If you are decreasing the specified level of maintenance, you
may distribute the new maintenance instructions to your customers 30
days after we receive your request, unless we disapprove your request.
We may approve a shorter time or waive this requirement.
(b) If your requested change would not decrease the specified level
of maintenance, you may distribute the new maintenance instructions
anytime after you send your request.
(c) If you are correcting or clarifying your maintenance
instructions or if you are changing instructions for maintenance
unrelated to emission controls, the requirements of this section do not
apply.
Sec. 1048.225 How do I amend my application to include new or
modified engines?
(a) You must amend your application for certification before you
take either of the following actions:
(1) Add an engine to a certificate of conformity (this includes any
changes you make in selecting emission standards under Sec.
1048.205(m)(1)).
(2) Make a design change for a certified engine family that may
affect emissions or an emission-related part over the engine's
lifetime.
(b) Send the Designated Officer a request to amend the application
for certification for an engine family. In your request, do all of the
following:
(1) Describe the engine model or configuration you are adding or
changing.
(2) Include engineering evaluations or reasons why the original
test engine is or is not still appropriate.
(3) If the original test engine for the engine family is not
appropriate to show compliance for the new or modified nonroad engine,
include new test data showing that the new or modified nonroad engine
meets the requirements of this part.
(c) You may start producing the new or modified nonroad engine
anytime after you send us your request. If we determine that the
affected engines do not meet applicable requirements, we will require
you to cease production of the engines and to recall and correct the
engines at no expense to the owner. If
[[Page 68356]]
you choose to produce engines under this paragraph (c), we will
consider that to be consent to recall all engines that we determine do
not meet applicable standards or other requirements and to remedy the
nonconformity at no expense to the owner.
(d) You must give us test data within 30 days if we ask for more
testing, or stop producing the engine if you cannot do this. You may
give us an engineering evaluation instead of test data if we agree that
you can address our questions without test data.
(e) If we determine that the certificate of conformity would not
cover your new or modified nonroad engine, we will send you a written
explanation of our decision. In this case, you may no longer produce
these engines, though you may ask for a hearing for us to reconsider
our decision (see Sec. 1048.820).
Sec. 1048.230 How do I select engine families?
(a) Divide your product line into families of engines that you
expect to have similar emission characteristics. Your engine family is
limited to a single model year.
(b) Group engines in the same engine family if they are the same in
all of the following aspects:
(1) The combustion cycle.
(2) The cooling system (water-cooled vs. air-cooled).
(3) Configuration of the fuel system (for example, fuel injection
vs. carburetion).
(4) Method of air aspiration.
(5) The number, location, volume, and composition of catalytic
converters.
(6) The number, arrangement, and approximate bore diameter of
cylinders.
(7) Evaporative emission controls.
(c) In some cases you may subdivide a group of engines that is
identical under paragraph (b) of this section into different engine
families. To do so, you must show you expect emission characteristics
to be different during the useful life or that any of the following
engine characteristics are different:
(1) Method of actuating intake and exhaust timing (poppet valve,
reed valve, rotary valve, etc.).
(2) Location or size of intake and exhaust valves or ports.
(3) Configuration of the combustion chamber.
(4) Cylinder stroke.
(5) Exhaust system.
(6) Type of fuel.
(d) If your engines are not identical with respect to the things
listed in paragraph (b) of this section, but you show that their
emission characteristics during the useful life will be similar, we may
approve grouping them in the same engine family.
(e) If you cannot appropriately define engine families by the
method in this section, we will define them based on features related
to emission characteristics.
(f) You may ask us to create separate families for exhaust
emissions and evaporative emissions. If we do this, list both families
on the emission control information label.
(g) Where necessary, you may divide an engine family into sub-
families to meet different emission standards, as specified in Sec.
1048.101(a)(2). For issues related to compliance and prohibited
actions, we will generally apply decisions to the whole engine family.
For engine labels and other administrative provisions, we may approve
your request for separate treatment of sub-families.
Sec. 1048.235 What emission testing must I perform for my application
for a certificate of conformity?
This section describes the emission testing you must perform to
show compliance with the emission standards in Sec. Sec. 1048.101(a)
and (b) and 1048.105 during certification. See Sec. 1048.205(s)
regarding emission testing related to the field-testing emission
standards.
(a) Test your emission-data engines using the procedures and
equipment specified in subpart F of this part. For any testing related
to evaporative emissions, use good engineering judgment to include a
complete fuel system with the engine.
(b) Select engine families according to the following criteria:
(1) For exhaust testing, select from each engine family a test
engine for each fuel type with a configuration that is most likely to
exceed the exhaust emission standards, using good engineering judgment.
Consider the emission levels of all exhaust constituents over the full
useful life of the engine when operated in a piece of equipment.
(2) For evaporative testing, select from each engine family a test
fuel system for each fuel type with a configuration that is most likely
to exceed the evaporative emission standards, using good engineering
judgment.
(c) You may use previously generated emission data in either of the
following cases:
(1) You may submit emission data for equivalent engine families
from previous years instead of doing new tests, but only if the data
show that the test engine would meet all the requirements for the
latest engine models. We may require you to do new emission testing if
we believe the latest engine models could be substantially different
from the previously tested engine.
(2) You may submit emission data for equivalent engine families
performed to show compliance with other standards (such as California
standards) instead of doing new tests, but only if the data show that
the test engine would meet all of this part's requirements.
(d) We may choose to measure emissions from any of your test
engines (or other engines from the engine family).
(1) If we do this, you must provide the test engine at the location
we select. We may decide to do the testing at your plant or any other
facility. If we choose to do the testing at your plant, you must
schedule it as soon as possible and make available the instruments and
equipment we need.
(2) If we measure emissions on one of your test engines, the
results of that testing become the official data for the engine. Unless
we later invalidate this data, we may decide not to consider your data
in determining if your engine family meets the emission standards.
(3) Before we test one of your engines, we may set its adjustable
parameters to any point within the physically adjustable ranges (see
Sec. 1048.115(e)).
(4) Calibrate the test engine within normal production tolerances
for anything we do not consider an adjustable parameter (see Sec.
1048.205(p)).
Sec. 1048.240 How do I demonstrate that my engine family complies
with exhaust emission standards?
(a) For certification, your engine family is considered in
compliance with the numerical emission standards in Sec. 1048.101 (a)
and (b), if all emission-data engines representing that family have
test results showing emission levels at or below these standards.
(b) Your engine family does not comply if any emission-data engine
representing that family has test results showing emission levels above
the standards from Sec. 1048.101 (a) and (b) for any pollutant.
(c) To compare emission levels from the test engine with the
emission standards, apply deterioration factors to the measured
emission levels. The deterioration factor is a number that shows the
relationship between exhaust emissions at the end of useful life and at
the low-hour test point. Specify the deterioration factors based on
emission measurements using four significant figures, consistent with
good engineering judgment. For example, deterioration factors must be
consistent with emission increases observed from in-use testing with
similar engines (see subpart E of this part). Small-volume
[[Page 68357]]
engine manufacturers may use assigned deterioration factors that we
establish. Apply the deterioration factors as follows:
(1) For engines that use aftertreatment technology, such as
catalytic converters, the deterioration factor is the ratio of exhaust
emissions at the end of useful life to exhaust emissions at the low-
hour test point. Adjust the official emission results for each tested
engine at the selected test point by multiplying the measured emissions
by the deterioration factor. If the factor is less than one, use one.
(2) For engines that do not use aftertreatment technology, the
deterioration factor is the difference between exhaust emissions at the
end of useful life and exhaust emissions at the low-hour test point.
Adjust the official emission results for each tested engine at the
selected test point by adding the factor to the measured emissions. If
the factor is less than zero, use zero.
(d) After adjusting the emission levels for deterioration, round
them to the same number of decimal places as the emission standard.
Compare the rounded emission levels to the emission standard for each
test engine.
Sec. 1048.245 How do I demonstrate that my engine family complies
with evaporative emission standards?
(a) For certification, your engine family is considered in
compliance with the evaporative emission standards in subpart B of this
part if you do either of the following:
(1) You have test results showing that evaporative emissions in the
family are at or below the standards throughout the useful life.
(2) Where applicable, you comply with the design specifications in
paragraph (e) of this section.
(b) Your engine family does not comply if any fuel system
representing that family has test results showing emission levels above
the standards.
(c) Use good engineering judgment to develop a test plan to
establish deterioration factors to show how much emissions increase at
the end of useful life.
(d) If you adjust the emission levels for deterioration, round them
to the same number of decimal places as the emission standard. Compare
the rounded emission levels to the emission standard for each test fuel
system.
(e) You may demonstrate that your engine family complies with the
evaporative emission standards by demonstrating that you use the
following control technologies:
(1) For certification to the standards specified in Sec.
1048.105(a)(1), with the following technologies:
(i) Use a tethered or self-closing gas cap on a fuel tank that
stays sealed up to a positive pressure of 24.5 kPa (3.5 psig) or a
vacuum pressure of 10.5 kPa (1.5 psig).
(ii) [Reserved]
(2) For certification to the standards specified in Sec.
1048.105(a)(3), demonstrating that you use design features to prevent
fuel boiling under all normal operation. You may do this using fuel
temperature data measured during normal operation.
(3) We may establish additional options for design-based
certification where we find that new test data demonstrate that a
technology will ensure compliance with the emission standards in this
section.
Sec. 1048.250 What records must I keep and make available to EPA?
(a) Organize and maintain the following records to keep them
readily available; we may review these records at any time:
(1) A copy of all applications and any summary information you sent
us.
(2) Any of the information we specify in Sec. 1048.205 that you
did not include in your application.
(3) A detailed history of each emission-data engine. In each
history, describe all of the following:
(i) The test engine's construction, including its origin and
buildup, steps you took to ensure that it represents production
engines, any components you built specially for it, and all emission-
related components.
(ii) How you accumulated engine operating hours, including the
dates and the number of hours accumulated.
(iii) All maintenance (including modifications, parts changes, and
other service) and the dates and reasons for the maintenance.
(iv) All your emission tests, including documentation on routine
and standard tests, as specified in part 40 CFR part 1065, and the date
and purpose of each test.
(v) All tests to diagnose engine or emission-control performance,
giving the date and time of each and the reasons for the test.
(vi) Any other significant events.
(b) Keep data from routine emission tests (such as test cell
temperatures and relative humidity readings) for one year after we
issue the associated certificate of conformity. Keep all other
information specified in paragraph (a) of this section for eight years
after we issue your certificate.
(c) Store these records in any format and on any media, as long as
you can promptly send us organized, written records in English if we
ask for them.
(d) Send us copies of any engine maintenance instructions or
explanations if we ask for them.
Sec. 1048.255 When may EPA deny, revoke, or void my certificate of
conformity?
(a) We may deny your application for certification if your engine
family fails to comply with emission standards or other requirements of
this part or the Act. Our decision may be based on any information
available to us showing you do not meet emission standards or other
requirements, including any testing that we conduct under paragraph (f)
of this section. If we deny your application, we will explain why in
writing.
(b) In addition, we may deny your application or revoke your
certificate if you do any of the following:
(1) Refuse to comply with any testing or reporting requirements.
(2) Submit false or incomplete information (paragraph (d) of this
section applies if this is fraudulent).
(3) Render inaccurate any test data.
(4) Deny us from completing authorized activities despite our
presenting a warrant or court order (see 40 CFR 1068.20).
(5) Produce engines for importation into the United States at a
location where local law prohibits us from carrying out authorized
activities.
(c) We may void your certificate if you do not keep the records we
require or do not give us information when we ask for it.
(d) We may void your certificate if we find that you intentionally
submitted false or incomplete information.
(e) If we deny your application or revoke or void your certificate,
you may ask for a hearing (see Sec. 1048.820). Any such hearing will
be limited to substantial and factual issues.
(f) We may conduct confirmatory testing of your engines as part of
certification. We may deny your application for certification or revoke
your certificate if your engines fail to comply with emission standards
or other requirements during confirmatory testing.
Subpart D--Testing Production-line Engines
Sec. 1048.301 When must I test my production-line engines?
(a) If you produce engines that are subject the requirements of
this part, you must test them as described in this subpart.
(b) We may suspend or revoke your certificate of conformity for
certain engine families if your production-line engines do not meet the
requirements of this part or you do not fulfill your
[[Page 68358]]
obligations under this subpart (see Sec. Sec. 1048.325 and 1048.340).
(c) Other requirements apply to engines that you produce. Other
regulatory provisions authorize us to suspend, revoke, or void your
certificate of conformity, or order recalls for engines families
without regard to whether they have passed these production-line
testing requirements. The requirements of this part do not affect our
ability to do selective enforcement audits, as described in part 1068
of this chapter. Individual engines in families that pass these
production-line testing requirements must also conform to all
applicable regulations of this part and part 1068 of this chapter.
(d) You may ask to use an alternate program for testing production-
line engines. In your request, you must show us that the alternate
program gives equal assurance that your production-line engines meet
the requirements of this part. If we approve your alternate program, we
may waive some or all of this subpart's requirements.
(e) If you certify an engine family with carryover emission data,
as described in Sec. 1048.235(c), and these equivalent engine families
consistently pass the production-line testing requirements over the
preceding two-year period, you may ask for a reduced testing rate for
further production-line testing for that family. The minimum testing
rate is one engine per engine family. If we reduce your testing rate,
we may limit our approval to any number of model years. In determining
whether to approve your request, we may consider the number of engines
that have failed the emission tests.
(f) We may ask you to make a reasonable number of production-line
engines available for a reasonable time so we can test or inspect them
for compliance with the requirements of this part.
Sec. 1048.305 How must I prepare and test my production-line engines?
(a) Test procedures. Test your production-line engines using either
the steady-state or transient testing procedures in subpart F of this
part to show you meet the emission standards in Sec. 1048.101(a) or
(b), respectively. We may require you to test engines using the
transient testing procedures to show you meet the emission standards in
Sec. 1048.101(a).
(b) Modifying a test engine. Once an engine is selected for testing
(see Sec. 1048.310), you may adjust, repair, prepare, or modify it or
check its emissions only if one of the following is true:
(1) You document the need for doing so in your procedures for
assembling and inspecting all your production engines and make the
action routine for all the engines in the engine family.
(2) This subpart otherwise specifically allows your action.
(3) We approve your action in advance.
(c) Engine malfunction. If an engine malfunction prevents further
emission testing, ask us to approve your decision to either repair the
engine or delete it from the test sequence.
(d) Setting adjustable parameters. Before any test, we may adjust
or require you to adjust any adjustable parameter to any setting within
its physically adjustable range.
(1) We may adjust idle speed outside the physically adjustable
range as needed only until the engine has stabilized emission levels
(see paragraph (e) of this section). We may ask you for information
needed to establish an alternate minimum idle speed.
(2) We may make or specify adjustments within the physically
adjustable range by considering their effect on emission levels, as
well as how likely it is someone will make such an adjustment with in-
use engines.
(e) Stabilizing emission levels. Before you test production-line
engines, you may operate the engine to stabilize the emission levels.
Using good engineering judgment, operate your engines in a way that
represents the way production engines will be used. You may operate
each engine for no more than the greater of two periods:
(1) 50 hours.
(2) The number of hours you operated your emission-data engine for
certifying the engine family (see 40 CFR part 1065, subpart E).
(f) Damage during shipment. If shipping an engine to a remote
facility for production-line testing makes necessary an adjustment or
repair, you must wait until after the after the initial emission test
to do this work. We may waive this requirement if the test would be
impossible or unsafe, or if it would permanently damage the engine.
Report to us, in your written report under Sec. 1048.345, all
adjustments or repairs you make on test engines before each test.
(g) Retesting after invalid tests. You may retest an engine if you
determine an emission test is invalid. Explain in your written report
reasons for invalidating any test and the emission results from all
tests. If you retest an engine and, within ten days after testing, ask
to substitute results of the new tests for the original ones, we will
answer within ten days after we receive your information.
Sec. 1048.310 How must I select engines for production-line testing?
(a) Use test results from two engines for each engine family to
calculate the required sample size for the model year. Update this
calculation with each test.
(b) Early in each calendar quarter, randomly select and test two
engines from the end of the assembly line for each engine family.
(c) Calculate the required sample size for each engine family.
Separately calculate this figure for HC+NOX and for CO. The
required sample size is the greater of these two calculated values. Use
the following equation:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.004
Where:
N = Required sample size for the model year.
t95 = 95% confidence coefficient, which depends on the
number of tests completed, n, as specified in the table in paragraph
(c)(1) of this section. It defines 95% confidence intervals for a
one-tail distribution.
x = Mean of emission test results of the sample.
STD = Emission standard.
[sigma]
= Test sample standard deviation (see paragraph (c)(2) of
this section).
(1) Determine the 95% confidence coefficient, t95, from
the following table:
----------------------------------------------------------------------------------------------------------------
n t95 n t95 n t95
----------------------------------------------------------------------------------------------------------------
2 6.31 12 1.80 22 1.72
3 2.92 13 1.78 23 1.72
4 2.35 14 1.77 24 1.71
5 2.13 15 1.76 25 1.71
6 2.02 16 1.75 26 1.71
7 1.94 17 1.75 27 1.71
8 1.90 18 1.74 28 1.70
9 1.86 19 1.73 29 1.70
[[Page 68359]]
10 1.83 20 1.73 30+ 1.70
11 1.81 21 1.72 ....................................
----------------------------------------------------------------------------------------------------------------
(2) Calculate the standard deviation, [sigma], for the test sample
using the following formula:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.005
Where:
Xi = Emission test result for an individual engine.
n = The number of tests completed in an engine family.
(d) Use final deteriorated test results to calculate the variables
in the equations in paragraph (c) of this section (see Sec.
1048.315(a)).
(e) After each new test, recalculate the required sample size using
the updated mean values, standard deviations, and the appropriate 95-
percent confidence coefficient.
(f) Distribute the remaining engine tests evenly throughout the
rest of the year. You may need to adjust your schedule for selecting
engines if the required sample size changes. Continue to randomly
select engines from each engine family; this may involve testing
engines that operate on different fuels.
(g) Continue testing any engine family for which the sample mean,
x, is greater than the emission standard. This applies if the sample
mean for either HC+NOX or for CO is greater than the
emission standard. Continue testing until one of the following things
happens:
(1) The sample size, n, for an engine family is greater than the
required sample size, N, and the sample mean, x, is less than or equal
to the emission standard. For example, if N = 3.1 after the third test,
the sample-size calculation does not allow you to stop testing.
(2) The engine family does not comply according to Sec. 1048.325.
(3) You test 30 engines from the engine family.
(4) You test one percent of your projected annual U.S.-directed
production volume for the engine family.
(5) You choose to declare that the engine family does not comply
with the requirements of this subpart.
(h) If the sample-size calculation allows you to stop testing for a
pollutant, you must continue measuring emission levels of that
pollutant for any additional tests required under this section.
However, you need not continue making the calculations specified in
this section for that pollutant. This paragraph (h) does not affect the
requirements in section Sec. 1048.320.
(i) You may elect to test more randomly chosen engines than we
require. Include these engines in the sample-size calculations.
Sec. 1048.315 How do I know when my engine family fails the
production-line testing requirements?
This section describes the pass/fail criteria for the production-
line testing requirements. We apply this criteria on an engine-family
basis. See Sec. 1048.320 for the requirements that apply to individual
engines that fail a production-line test.
(a) Calculate your test results. Round them to the number of
decimal places in the emission standard expressed to one more decimal
place.
(1) Initial and final test results. Calculate and round the test
results for each engine. If you do several tests on an engine,
calculate the initial test results, then add them together and divide
by the number of tests and round for the final test results on that
engine.
(2) Final deteriorated test results. Apply the deterioration factor
for the engine family to the final test results (see Sec.
1048.240(c)).
(b) Construct the following CumSum Equation for each engine family
(for HC+NOX and for CO emissions):
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.006
Where:
Ci = The current CumSum statistic.
Ci-1 = The previous CumSum statistic. For the first test,
CumSum statistic is 0 (i.e. C1 = 0).
Xi = The current emission test result for an individual
engine.
STD = Emission standard.
(c) Use final deteriorated test results to calculate the variables
in the equation in paragraph (b) of this section (see Sec.
1048.315(a)).
(d) After each new test, recalculate the CumSum statistic.
(e) If you test more than the required number of engines, include
the results from these additional tests in the CumSum Equation.
(f) After each test, compare the current CumSum statistic,
Ci, to the recalculated Action Limit, H, defined as H = 5.0
x [sigma].
(g) If the CumSum statistic exceeds the Action Limit in two
consecutive tests, the engine family fails the production-line testing
requirements of this subpart. Tell us within ten working days if this
happens.
(h) If you amend the application for certification for an engine
family (see Sec. 1048.225), do not change any previous calculations of
sample size or CumSum statistics for the model year.
Sec. 1048.320 What happens if one of my production-line engines fails
to meet emission standards?
If you have a production-line engine with final deteriorated test
results exceeding one or more emission standards (see Sec.
1048.315(a)), the certificate of conformity is automatically suspended
for that failing engine. You must take the following actions before
your certificate of conformity can cover that engine:
(a) Correct the problem and retest the engine to show it complies
with all emission standards.
(b) Include in your written report a description of the test
results and the remedy for each engine (see Sec. 1048.345).
Sec. 1048.325 What happens if an engine family fails the production-
line requirements?
(a) We may suspend your certificate of conformity for an engine
family if it fails under Sec. 1048.315. The suspension may apply to
all facilities producing engines from an engine family, even if you
find noncompliant engines only at one facility.
(b) We will tell you in writing if we suspend your certificate in
whole or in part. We will not suspend a certificate until at least 15
days after the engine family fails. The suspension is effective when
you receive our notice.
(c) Up to 15 days after we suspend the certificate for an engine
family, you may ask for a hearing (see Sec. 1048.820). If we agree
before a hearing that we used erroneous information in deciding to
suspend the certificate, we will reinstate the certificate.
(d) Section Sec. 1048.335 specifies steps you must take to remedy
the cause of the production-line failure. All the engines you have
produced since the end of the last test period are presumed
noncompliant and should be addressed in your proposed remedy. We may
require you to apply the remedy to engines produced earlier if we
determine that the cause of the failure is likely to have affected the
earlier engines.
[[Page 68360]]
Sec. 1048.330 May I sell engines from an engine family with a
suspended certificate of conformity?
You may sell engines that you produce after we suspend the engine
family's certificate of conformity under Sec. 1048.315 only if one of
the following occurs:
(a) You test each engine you produce and show it complies with
emission standards that apply.
(b) We conditionally reinstate the certificate for the engine
family. We may do so if you agree to recall all the affected engines
and remedy any noncompliance at no expense to the owner if later
testing shows that the engine family still does not comply.
Sec. 1048.335 How do I ask EPA to reinstate my suspended certificate?
(a) Send us a written report asking us to reinstate your suspended
certificate. In your report, identify the reason for noncompliance,
propose a remedy for the engine family, and commit to a date for
carrying it out. In your proposed remedy include any quality control
measures you propose to keep the problem from happening again.
(b) Give us data from production-line testing that shows the
remedied engine family complies with all the emission standards that
apply.
Sec. 1048.340 When may EPA revoke my certificate under this subpart
and how may I sell these engines again?
(a) We may revoke your certificate for an engine family in the
following cases:
(1) You do not meet the reporting requirements.
(2) Your engine family fails to comply with the requirements of
this subpart and your proposed remedy to address a suspended
certificate under Sec. 1048.325 is inadequate to solve the problem or
requires you to change the engine's design or emission-control system.
(b) To sell engines from an engine family with a revoked
certificate of conformity, you must modify the engine family and then
show it complies with the requirements of this part.
(1) If we determine your proposed design change may not control
emissions for the engine's full useful life, we will tell you within
five working days after receiving your report. In this case we will
decide whether production-line testing will be enough for us to
evaluate the change or whether you need to do more testing.
(2) Unless we require more testing, you may show compliance by
testing production-line engines as described in this subpart.
(3) We will issue a new or updated certificate of conformity when
you have met these requirements.
Sec. 1048.345 What production-line testing records must I send to
EPA?
Do all the following things unless we ask you to send us less
information:
(a) Within 30 calendar days of the end of each calendar quarter,
send us a report with the following information:
(1) Describe any facility used to test production-line engines and
state its location.
(2) State the total U.S.-directed production volume and number of
tests for each engine family.
(3) Describe how you randomly selected engines.
(4) Describe your test engines, including the engine family's
identification and the engine's model year, build date, model number,
identification number, and number of hours of operation before testing
for each test engine.
(5) Identify where you accumulated hours of operation on the
engines and describe the procedure and schedule you used.
(6) Provide the test number; the date, time and duration of
testing; test procedure; initial test results before and after
rounding; final test results; and final deteriorated test results for
all tests. Provide the emission results for all measured pollutants.
Include information for both valid and invalid tests and the reason for
any invalidation.
(7) Describe completely and justify any nonroutine adjustment,
modification, repair, preparation, maintenance, or test for the test
engine if you did not report it separately under this subpart. Include
the results of any emission measurements, regardless of the procedure
or type of equipment.
(8) Provide the CumSum analysis required in Sec. 1048.315 for each
engine family.
(9) Report on each failed engine as described in Sec. 1048.320.
(10) State the date the calendar quarter ended for each engine
family.
(b) We may ask you to add information to your written report, so we
can determine whether your new nonroad engines conform with the
requirements of this subpart.
(c) An authorized representative of your company must sign the
following statement:
We submit this report under Sections 208 and 213 of the Clean
Air Act. Our production-line testing conformed completely with the
requirements of 40 CFR part 1048. We have not changed production
processes or quality-control procedures for the engine family in a
way that might affect the emission control from production engines.
All the information in this report is true and accurate, to the best
of my knowledge. I know of the penalties for violating the Clean Air
Act and the regulations. (Authorized Company Representative)
(d) Send electronic reports of production-line testing to the
Designated Officer using an approved information format. If you want to
use a different format, send us a written request with justification
for a waiver.
(e) We will send copies of your reports to anyone from the public
who asks for them. See Sec. 1048.815 for information on how we treat
information you consider confidential.
Sec. 1048.350 What records must I keep?
(a) Organize and maintain your records as described in this
section. We may review your records at any time, so it is important to
keep required information readily available.
(b) Keep paper records of your production-line testing for one full
year after you complete all the testing required for an engine family
in a model year. You may use any additional storage formats or media if
you like.
(c) Keep a copy of the written reports described in Sec. 1048.345.
(d) Keep the following additional records:
(1) A description of all test equipment for each test cell that you
can use to test production-line engines.
(2) The names of supervisors involved in each test.
(3) The name of anyone who authorizes adjusting, repairing,
preparing, or modifying a test engine and the names of all supervisors
who oversee this work.
(4) If you shipped the engine for testing, the date you shipped it,
the associated storage or port facility, and the date the engine
arrived at the testing facility.
(5) Any records related to your production-line tests that are not
in the written report.
(6) A brief description of any significant events during testing
not otherwise described in the written report or in this section.
(7) Any information specified in Sec. 1048.345 that you do not
include in your written reports.
(e) If we ask, you must give us projected or actual production
figures for an engine family. We may ask you to divide your production
figures by maximum brake power, displacement, fuel type, or assembly
plant (if you produce engines at more than one plant).
(f) Keep a list of engine identification numbers for all the
engines you produce under each certificate of conformity. Give us this
list within 30 days if we ask for it.
[[Page 68361]]
(g) We may ask you to keep or send other information necessary to
implement this subpart.
Subpart E--Testing In-use Engines
Sec. 1048.401 What testing requirements apply to my engines that have
gone into service?
(a) If you produce engines that are subject to the requirements of
this part, you must test them as described in this subpart. This
generally involves testing engines in the field or removing them for
measurement in a laboratory.
(b) We may approve an alternate plan for showing that in-use
engines comply with the requirements of this part if one of the
following is true:
(1) You produce 200 or fewer engines per year in the selected
engine family.
(2) Removing the engine from most of the applications for that
engine family causes significant, irreparable damage to the equipment.
(3) You identify a unique aspect of your engine applications that
keeps you from doing the required in-use testing.
(c) We may void your certificate of conformity for an engine family
if you do not meet your obligations under this part.
(d) Independent of your responsibility to test in-use engines, we
may choose at any time to do our own testing of your in-use engines.
(e) If in-use testing shows that engines fail to meet emission
standards or other requirements of this part, we may pursue a recall or
other remedy as allowed by the Act (see Sec. 1048.415).
Sec. 1048.405 How does this program work?
(a) You must test in-use engines, for exhaust emissions, from the
families we select. We may select up to 25 percent of your engine
families in any model year--or one engine family if you have three or
fewer families. We will select engine families for testing before the
end of the model year. When we select an engine family for testing, we
may specify that you preferentially test engines based on fuel type or
equipment type. In addition, we may identify specific modes of
operation or sampling times. You may choose to test additional engine
families that we do not select.
(b) Send us an in-use testing plan within 12 calendar months after
we direct you to test a particular engine family. Complete the testing
within 24 calendar months after we approve your plan.
(c) You may need to test engines from more than one model year at a
given time.
Sec. 1048.410 How must I select, prepare, and test my in-use engines?
(a) You may make arrangements to select representative test engines
from your own fleet or from other independent sources.
(b) For the selected engine families, select engines that you or
your customers have--
(1) Operated for at least 50 percent of the engine family's useful
life (see Sec. 1048.101(d));
(2) Not maintained or used in an abnormal way; and
(3) Documented in terms of total hours of operation, maintenance,
operating conditions, and storage.
(c) Use the following methods to determine the number of engines
you must test in each engine family:
(1) Test at least two engines if you produce 2,000 or fewer engines
in the model year from all engine families, or if you produce 500 or
fewer engines from the selected engine family. Otherwise, test at least
four engines.
(2) If you successfully complete an in-use test program on an
engine family and later certify an equivalent engine family with
carryover emission data, as described in Sec. 1048.235(c), then test
at least one engine instead of the testing rates in paragraph (c)(1) of
this section.
(3) If you test the minimum required number of engines and all
comply fully with emission standards, you may stop testing.
(4) For each engine that fails any applicable standard, test two
more. Regardless of measured emission levels, you do not have to test
more than ten engines in an engine family. You may do more tests than
we require.
(5) You may concede that the engine family does not comply before
testing a total of ten engines.
(d) You may do minimal maintenance to set components of a test
engine to specifications for anything we do not consider an adjustable
parameter (see Sec. 1048.205(p)). Limit maintenance to what is in the
owner's instructions for engines with that amount of service and age.
Document all maintenance and adjustments.
(e) Do at least one valid exhaust emission test for each test
engine.
(f) For a test program on an engine family, choose one of the
following methods to test your engines:
(1) Remove the selected engines for testing in a laboratory. Use
the applicable steady-state and transient procedures in subpart F of
this part to show compliance with the duty-cycle standards in Sec.
1048.101(a) and (b). We may direct you to measure emissions on the
dynamometer using the supplemental test procedures in Sec. 1048.515 to
show compliance with the field-testing standards in Sec. 1048.101(c).
(2) Test the selected engines while they remain installed in the
equipment. Use the field testing procedures in subpart F of this part.
Measure emissions during normal operation of the equipment to show
compliance with the field-testing standards in Sec. 1048.101(c). We
may direct you to include specific areas of normal operation.
(g) You may ask us to waive parts of the prescribed test procedures
if they are not necessary to determine in-use compliance.
(h) Calculate the average emission levels for an engine family from
the results for the set of tested engines. Round them to the number of
decimal places in the emission standards expressed to one more decimal
place.
Sec. 1048.415 What happens if in-use engines do not meet
requirements?
(a) Determine the reason each in-use engine exceeds the emission
standards.
(b) If the average emission levels calculated in Sec. 1048.410(h)
exceed any of the emission standards that apply, notify us within
fifteen days of completing testing on this family. Otherwise follow the
reporting instructions in Sec. 1048.420.
(c) We will consider failure rates, average emission levels, and
any defects--among other things--to decide on taking remedial action
under this subpart (see 40 CFR 1068.505). We may consider the results
from any voluntary additional testing you conduct. We may also consider
information related to testing from other engine families showing that
you designed them to exceed the minimum requirements for controlling
emissions. We may order a recall before or after you complete testing
of an engine family if we determine a substantial number of engines do
not conform to section 213 of the Act or to this part.
(d) If in-use testing reveals a design or manufacturing defect that
prevents engines from meeting the requirements of this part, you must
correct the defect as soon as possible for any future production for
engines in every family affected by the defect.
(e) You may voluntarily recall an engine family for emission
failures, as described in 40 CFR 1068.535, unless we have ordered a
recall for that family under 40 CFR 1068.505.
(f) You have the right to a hearing before we order you to recall
your engines or implement an alternative remedy (see Sec. 1048.820).
[[Page 68362]]
Sec. 1048.420 What in-use testing information must I report to EPA?
(a) In a report to us within three months after you finish testing
an engine family, do all the following:
(1) Identify the engine family, model, serial number, and date of
manufacture.
(2) For each engine inspected or considered for testing, identify
whether the diagnostic system was functioning.
(3) Describe the specific reasons for disqualifying any engines for
not being properly maintained or used.
(4) For each engine selected for testing, include the following
information:
(i) Estimate the hours each engine was used before testing.
(ii) Describe all maintenance, adjustments, modifications, and
repairs to each test engine.
(5) State the date and time of each test attempt.
(6) Include the results of all emission testing, including
incomplete or invalidated tests, if any.
(b) Send electronic reports of in-use testing to the Designated
Officer using an approved information format. If you want to use a
different format, send us a written request with justification for a
waiver.
(c) We will send copies of your reports to anyone from the public
who asks for them. See Sec. 1048.815 for information on how we treat
information you consider confidential.
(d) We may ask for more information.
Sec. 1048.425 What records must I keep?
(a) Organize and maintain your records as described in this
section. We may review your records at any time, so it is important to
keep required information readily available.
(b) Keep paper records of your in-use testing for one full year
after you complete all the testing required for an engine family in a
model year. You may use any additional storage formats or media if you
like.
(c) Keep a copy of the written reports described in Sec. 1048.420.
(d) Keep any additional records related to the procurement process.
Subpart F--Test Procedures
Sec. 1048.501 What procedures must I use to test my engines?
(a) Use the equipment and procedures for spark-ignition engines in
40 CFR part 1065 to show your engines meet the duty-cycle emission
standards in Sec. 1048.101(a) and (b). Measure HC, NOX, CO,
and CO2 emissions using the full-flow dilute sampling
procedures in 40 CFR part 1065. Use the applicable duty cycles in
Sec. Sec. 1048.505 and 1048.510.
(b) We describe in Sec. 1048.515 the supplemental procedures for
showing that your engines meet the field-testing emission standards in
Sec. 1048.101(c).
(c) Use the fuels specified in 40 CFR part 1065, subpart C, for all
the testing we require in this part, except as noted in Sec. 1048.515.
Use these test fuels or any commercially available fuel for service
accumulation.
(d) To test engines for evaporative emissions, use the equipment
and procedures specified for testing diurnal emissions in 40 CFR
86.107-96 and 86.133-96 with fuel meeting the specifications in 40 CFR
part 1065, subpart C. Measure emissions from a test engine with a
complete fuel system. Reported emission levels must be based on the
highest emissions from three successive 24-hour periods of cycling
temperatures. Note that you may not be required to test for evaporative
emissions during certification if you certify by design, as specified
in Sec. 1048.245.
(e) You may use special or alternate procedures, as described in 40
CFR 1065.10.
(f) We may reject data you generate using alternate procedures if
later testing with the procedures in 40 CFR part 1065 shows
contradictory emission data.
Sec. 1048.505 What steady-state duty cycles apply for laboratory
testing?
(a) Measure emissions by testing the engine on a dynamometer with
one or more of the following sets of steady-state duty cycles to show
that the engine meets the steady-state standards in Sec. 1048.101(b):
(1) Use the 7-mode duty cycle described in the following table for
engines from an engine family that will be used only in variable-speed
applications:
Table 1 of Sec. 1048.505--7-Mode Duty Cycle \1\
----------------------------------------------------------------------------------------------------------------
Minimum
Observed time in Weighting
Mode No. Engine speed torque \2\ mode factors
(minutes)
----------------------------------------------------------------------------------------------------------------
1....................................... Maximum test speed............. 25 3.0 0.06
2....................................... Intermediate test speed........ 100 3.0 0.02
3....................................... Intermediate test speed........ 75 3.0 0.05
4....................................... Intermediate test speed........ 50 3.0 0.32
5....................................... Intermediate test speed........ 25 3.0 0.30
6....................................... Intermediate test speed........ 10 3.0 0.10
7....................................... Idle........................... 0 3.0 0.15
----------------------------------------------------------------------------------------------------------------
\1\ This duty cycle is analogous to the C2 cycle specified in ISO 8178-4.
\2\ The percent torque is relative to the maximum torque at the given engine speed.
(2) Use the 5-mode duty cycle described in the following table if
you certify an engine family for operation only at a single, rated
speed:
Table 2 of Sec. 1048.505--5-Mode Duty Cycle for Constant-Speed Engines \1\
----------------------------------------------------------------------------------------------------------------
Minimum
time in Weighting
Mode No. Engine speed Torque \2\ mode factors
(minutes)
----------------------------------------------------------------------------------------------------------------
1....................................... Maximum test................... 100 3.0 0.05
2....................................... Maximum test................... 75 3.0 0.25
3....................................... Maximum test................... 50 3.0 0.30
[[Page 68363]]
4....................................... Maximum test................... 25 3.0 0.30
5....................................... Maximum test................... 10 3.0 0.10
----------------------------------------------------------------------------------------------------------------
\1\ This duty cycle is analogous to the D2 cycle specified in ISO 8178-4.
\2\ The percent torque is relative to the maximum torque at maximum test speed.
(3) Use both of the duty cycles described in paragraphs (a)(1) and
(a)(2) of this section if you will not restrict an engine family to
constant-speed or variable-speed applications.
(4) Use only the duty cycle specified in paragraph (a)(2) of this
section for all severe-duty engines.
(5) Use the 2-mode duty cycle described in the following table for
high-load engines instead of the other duty cycles in this paragraph
(a):
Table 3 of Sec. 1048.505--2-Mode Duty Cycle for High-Load Engines \1\
----------------------------------------------------------------------------------------------------------------
Minimum
time in Weighting
Mode No. Engine speed Torque \2\ mode factors
(minutes)
----------------------------------------------------------------------------------------------------------------
1....................................... Maximum test................... 100 3.0 0.50
2....................................... Maximum test................... 75 3.0 0.50
----------------------------------------------------------------------------------------------------------------
\1\ This duty cycle is derived from the D1 cycle specified in ISO 8178-4.
\2\ The percent torque is relative to the maximum torque at maximum test speed.
(b) If we test an engine to confirm that it meets the duty-cycle
emission standards, we will use the steady-state duty cycles that apply
for that engine family.
(c) During idle mode, operate the engine with the following
parameters:
(1) Hold the speed within your specifications.
(2) Keep the throttle at the idle-stop position.
(3) Keep engine torque under 5 percent of the peak torque value at
maximum test speed.
(d) For the full-load operating mode, operate the engine at wide-
open throttle.
(e) See 40 CFR part 1065 for detailed specifications of tolerances
and calculations.
(f) In the normal test sequence described in 40 CFR part 1065,
subpart F, steady-state testing generally follows the transient test.
For those cases where we do not require transient testing, perform the
steady-state test after an appropriate warm-up period, consistent with
good engineering judgment.
Sec. 1048.510 What transient duty cycles apply for laboratory
testing?
(a) Starting with the 2007 model year, measure emissions by testing
the engine on a dynamometer with one of the following transient duty
cycles to show that the engine meets the transient emission standards
in Sec. 1048.101(a):
(1) If you certify an engine family for constant-speed operation
only, use the transient duty-cycle described in Appendix I of this
part.
(2) For all other engines, use the transient duty-cycle described
in Appendix II of this part.
(b) If we test an engine to confirm that it meets the duty-cycle
emission standards, we will use the transient duty cycle that applies
for that engine family.
(c) Warm up the test engine as follows:
(1) Operate the engine for the first 180 seconds of the appropriate
duty cycle, then allow it to idle without load for 30 seconds. At the
end of the 30-second idling period, start measuring emissions as the
engine operates over the prescribed duty cycle. For severe-duty
engines, this engine warm-up procedure may include up to 15 minutes of
operation over the appropriate duty cycle.
(2) If the engine was already operating before a test, use good
engineering judgment to let the engine cool down enough so measured
emissions during the next test will accurately represent those from an
engine starting at room temperature. For example, if an engine starting
at room temperature warms up enough in three minutes to start closed-
loop operation and achieve full catalyst activity, then minimal engine
cooling is necessary before starting the next test.
(3) You are not required to measure emissions while the engine is
warming up. However, you must design your emission-control system to
start working as soon as possible after engine starting. In your
application for certification, describe how your engine meets this
objective (see Sec. 1048.205(b)).
Sec. 1048.515 Field-testing procedures.
(a) This section describes the procedures to determine whether your
engines meet the field-testing emission standards in Sec. 1048.101(c).
These procedures may include any normal engine operation and ambient
conditions that the engines may experience in use. Paragraph (b) of
this section defines the limits of what we will consider normal engine
operation and ambient conditions. Use the test procedures we specify in
Sec. 1048.501, except for the provisions we specify in this section.
Measure emissions with one of the following procedures:
(1) Remove the selected engines for testing in a laboratory. You
can use an engine dynamometer to simulate normal operation, as
described in this section.
(2) Test the selected engines while they remain installed in the
equipment. In 40 CFR part 1065, subpart J, we describe the equipment
and sampling methods for testing engines in the field. Use fuel meeting
the specifications of 40 CFR 1065.210 or a fuel typical of what you
would expect the engine to use in service.
(b) An engine's emissions may not exceed the levels we specify in
Sec. 1048.101(c) for any continuous sampling period of at least 120
seconds
[[Page 68364]]
under the following ranges of operation and operating conditions:
(1) Engine operation during the emission sampling period may
include any normal operation, subject to the following restrictions:
(i) Average power must be over 5 percent of maximum brake power.
(ii) Continuous time at idle must not be greater than 120 seconds.
(iii) The sampling period may not begin until the engine has
reached stable operating temperatures. For example, this would exclude
engine operation after starting until the thermostat starts modulating
coolant temperature.
(iv) The sampling period may not include engine starting.
(v) For engines that qualify for the alternate Tier 2 emission
standards in Sec. 1048.101(d), operation at 90 percent or more of
maximum power must be less than 10 percent of the total sampling time.
You may request our approval for a different power threshold.
(2) Engine testing may occur under any normal conditions without
correcting measured emission levels, subject to the following
restrictions:
(i) Barometric pressure must be between 80.0 and 103.3 kPa (600 and
775 mm Hg).
(ii) Ambient air temperature must be between 13[deg]
and 35[deg]
C.
Subpart G--Compliance Provisions
Sec. 1048.601 What compliance provisions apply to these engines?
Engine and equipment manufacturers, as well as owners, operators,
and rebuilders of these engines, and all other persons, must observe
the requirements and prohibitions in 40 CFR part 1068 and the
requirements of the Act. The compliance provisions in this subpart
apply only to the engines we regulate in this part.
Sec. 1048.605 What are the provisions for exempting engines from the
requirements of this part if they are already certified under the
motor-vehicle program?
(a) This section applies to you if you are an engine manufacturer.
See Sec. 1048.610 if you are not an engine manufacturer.
(b) The only requirements or prohibitions from this part that apply
to an engine that is exempt under this section are in this section.
(c) If you meet all the following criteria and requirements
regarding your new nonroad engine, it is exempt under this section:
(1) You must produce it by modifying an engine covered by a valid
certificate of conformity under 40 CFR part 86.
(2) Do not make any changes to the certified engine that we could
reasonably expect to increase its exhaust or evaporative emissions. For
example, if you make any of the following changes to one of these
engines, you do not qualify for this exemption:
(i) Change any fuel system or evaporative system parameters from
the certified configuration (this does not apply to refueling emission
controls).
(ii) Change any other emission-related components.
(iii) Modify or design the engine cooling system so that
temperatures or heat rejection rates are outside the original engine
manufacturer's specified ranges.
(3) Demonstrate that fewer than 50 percent of the engine model's
total sales, from all companies, are used in nonroad applications.
(4) The engine must have the label we require under 40 CFR part 86.
(5) Add a permanent supplemental label to the engine in a position
where it will remain clearly visible after installation in the
equipment. In your engine's emission control information label, do the
following:
(i) Include the heading: ``Nonroad Engine Emission Control
Information''.
(ii) Include your full corporate name and trademark.
(iii) State: ``THIS ENGINE WAS ADAPTED FOR NONROAD USE WITHOUT
AFFECTING ITS EMISSION CONTROLS.''.
(iv) State the date you finished modifying the engine (month and
year).
(6) The original and supplemental labels must be readily visible
after the engine is installed in the equipment or, if the equipment
obscures the engine's emission control information label, the equipment
manufacturer must attach duplicate labels, as described in 40 CFR
1068.105.
(7) Send the Designated Officer a signed letter by the end of each
calendar year (or less often if we tell you) with all the following
information:
(i) Identify your full corporate name, address, and telephone
number.
(ii) List the engine models you expect to produce under this
exemption in the coming year.
(iii) State: ``We produce each listed engine model for nonroad
application without making any changes that could increase its
certified emission levels, as described in 40 CFR 1048.605.''.
(d) If your engines do not meet the criteria listed in paragraph
(c) of this section, they will be subject to the standards and
prohibitions of this part. Producing these engines without a valid
exemption or certificate of conformity would violate the prohibitions
in 40 CFR 1068.101.
(e) If you are the original engine manufacturer of both the highway
and nonroad versions of an exempted engine, you must send us emission
test data on the applicable nonroad duty cycle(s). You may include the
data in your application for certification or in your letter requesting
the exemption.
(f) If you are the original engine manufacturer of an exempted
engine that is modified by another company under this exemption, we may
require you to send us emission test data on the applicable nonroad
duty cycle(s). If we ask for this data, we will allow a reasonable
amount of time to collect it.
(g) The engine exempted under this section must meet all applicable
requirements from 40 CFR part 86. This applies to engine manufacturers,
equipment manufacturers who use these engines, and all other persons as
if these engines were used in a motor vehicle.
Sec. 1048.610 What are the provisions for producing nonroad equipment
with engines already certified under the motor-vehicle program?
If you are not an engine manufacturer, you may produce nonroad
equipment from complete or incomplete motor vehicles with the motor
vehicle engine if you meet three criteria:
(a) The engine or vehicle is certified to 40 CFR part 86.
(b) The engine is not adjusted outside the engine manufacturer's
specifications (see Sec. 1048.605(c)(2)).
(c) The engine or vehicle is not modified in any way that may
affect its emission control. This applies to exhaust and evaporative
emission controls, but not refueling emission controls.
Sec. 1048.615 What are the provisions for exempting engines designed
for lawn and garden applications?
This section is intended for engines designed for lawn and garden
applications, but it applies to any engines meeting the size criteria
in paragraph (a) of this section.
(a) If an engine meets all the following criteria, it is exempt
from the requirements of this part:
(1) The engine must have a total displacement of 1,000 cc or less.
(2) The engine must have a maximum brake power of 30 kW or less.
(3) The engine must be in an engine family that has a valid
certificate of conformity showing that it meets emission standards for
Class II engines under 40 CFR part 90.
(b) The only requirements or prohibitions from this part that apply
to an engine that meets the criteria in paragraph (a) of this section
are in this section.
[[Page 68365]]
(c) If your engines do not meet the criteria listed in paragraph
(a) of this section, they will be subject to the provisions of this
part. Producing these engines without a valid exemption or certificate
of conformity would violate the prohibitions in 40 CFR 1068.101.
(d) Engines exempted under this section are subject to all the
requirements affecting engines under 40 CFR part 90. The requirements
and restrictions of 40 CFR part 90 apply to anyone manufacturing these
engines, anyone manufacturing equipment that uses these engines, and
all other persons in the same manner as if these engines had a total
maximum brake power at or below 19 kW.
Sec. 1048.620 What are the provisions for exempting large engines
fueled by natural gas?
(a) If an engine meets all the following criteria, it is exempt
from the requirements of this part:
(1) The engine must operate solely on natural gas.
(2) The engine must have maximum brake power 250 kW or higher.
(3) The engine must be in an engine family that has a valid
certificate of conformity showing that it meets emission standards for
engines of that power rating under 40 CFR part 89.
(b) The only requirements or prohibitions from this part that apply
to an engine that is exempt under this section are in this section.
(c) If your engines do not meet the criteria listed in paragraph
(a) of this section, they will be subject to the provisions of this
part. Producing these engines without a valid exemption or certificate
of conformity would violate the prohibitions in 40 CFR 1068.101.
(d) Engines exempted under this section are subject to all the
requirements affecting engines under 40 CFR part 89. The requirements
and restrictions of 40 CFR part 89 apply to anyone manufacturing these
engines, anyone manufacturing equipment that uses these engines, and
all other persons in the same manner as if these were nonroad diesel
engines.
(e) You may request an exemption under this section by submitting
an application for certification for the engines under 40 CFR part 89.
Sec. 1048.625 What special provisions apply to engines using
noncommercial fuels?
If you are unable to meet this part's requirements with engines
using noncommercial fuels (such as unrefined natural gas released by
oil wells), the following provisions apply for those engines:
(a) Create a separate engine family.
(b) Disregard the limits on adjustable parameters in Sec.
1048.115(e), but make sure the engines meet emission standards with
normal settings when the engine is using fuel meeting the
specifications of 40 CFR part 1065, subpart C.
(c) Add the following information to the emission control
information label specified in Sec. 1048.135:
(1) Include instructions describing how to adjust the engine to
operate in a way that maintains the effectiveness of the emission-
control system.
(2) State: ``THIS ENGINE IS CERTIFIED TO OPERATE IN APPLICATIONS
USING NONCOMMERCIAL FUEL. USING IT IN AN APPLICATION INVOLVING ONLY
COMMERCIAL FUELS MAY BE A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL
PENALTY.''.
(d) Keep records to document the destinations and quantities of
engines produced under this section.
Subpart H--[Reserved]
Subpart I--Definitions and Other Reference Information
Sec. 1048.801 What definitions apply to this part?
The following definitions apply to this part. The definitions apply
to all subparts unless we note otherwise. All undefined terms have the
meaning the Act gives to them. The definitions follow:
Act means the Clean Air Act, as amended, 42 U.S.C. 7401 et seq.
Adjustable parameter means any device, system, or element of design
that someone can adjust (including those which are difficult to access)
and that, if adjusted, may affect emissions or engine performance
during emission testing or normal in-use operation. You may ask us to
exclude a parameter that is difficult to access if it cannot be
adjusted to affect emissions without significantly degrading
performance, or if you otherwise show us that it will not be adjusted
in a way that affects emissions during in-use operation.
Aftertreatment means relating to any system, component, or
technology mounted downstream of the exhaust valve or exhaust port
whose design function is to reduce exhaust emissions.
Aircraft means any vehicle capable of sustained air travel above
treetop heights.
All-terrain vehicle has the meaning we give in 40 CFR 1051.801.
Auxiliary emission-control device means any element of design that
senses temperature, engine rpm, motive speed, transmission gear,
atmospheric pressure, manifold pressure or vacuum, or any other
parameter to activate, modulate, delay, or deactivate the operation of
any part of the emission-control system. This also includes any other
feature that causes in-use emissions to be higher than those measured
under test conditions, except as we allow under this part.
Blue Sky Series engine means an engine meeting the requirements of
Sec. 1048.140.
Brake power means the usable power output of the engine, not
including power required to operate fuel pumps, oil pumps, or coolant
pumps.
Broker means any entity that facilitates a trade of emission
credits between a buyer and seller.
Calibration means the set of specifications and tolerances specific
to a particular design, version, or application of a component or
assembly capable of functionally describing its operation over its
working range.
Certification means obtaining a certificate of conformity for an
engine family that complies with the emission standards and
requirements in this part.
Compression-ignition means relating to a type of reciprocating,
internal-combustion engine that is not a spark-ignition engine.
Constant-speed engine means an engine governed to operate at a
single speed.
Crankcase emissions means airborne substances emitted to the
atmosphere from any part of the engine crankcase's ventilation or
lubrication systems. The crankcase is the housing for the crankshaft
and other related internal parts.
Designated Officer means the Manager, Engine Programs Group (6405-
J), U.S. Environmental Protection Agency, 1200 Pennsylvania Ave.,
Washington, DC 20460.
Emission-control system means any device, system, or element of
design that controls or reduces the regulated emissions from an engine.
Emission-data engine means an engine that is tested for
certification.
Emission-related maintenance means maintenance that substantially
affects emissions or is likely to substantially affect emissions
deterioration.
Engine family means a group of engines with similar emission
characteristics, as specified in Sec. 1048.230.
Engine manufacturer means the manufacturer of the engine. See the
definition of ``manufacturer'' in this section.
Fuel system means all components involved in transporting,
metering, and mixing the fuel from the fuel tank to the
[[Page 68366]]
combustion chamber(s), including the fuel tank, fuel tank cap, fuel
pump, fuel filters, fuel lines, carburetor or fuel-injection
components, and all fuel-system vents.
Good engineering judgment has the meaning we give in 40 CFR 1068.5.
High-cost warranted part means a component covered by the emission-
related warranty with a replacement cost (at the time of certification)
exceeding $400 (in 1998 dollars). Adjust this value using the most
recent annual average consumer price index information published by the
U.S. Bureau of Labor Statistics. For this definition, replacement cost
includes the retail cost of the part plus labor and standard diagnosis.
High-load engine means an engine for which the engine manufacturer
can provide clear evidence that operation below 75 percent of maximum
load in it's final application will be rare.
Hydrocarbon (HC) means the hydrocarbon group on which the emission
standards are based for each fuel type. For gasoline- and LPG-fueled
engines, HC means total hydrocarbon (THC). For natural gas-fueled
engines, HC means nonmethane hydrocarbon (NMHC). For alcohol-fueled
engines, HC means total hydrocarbon equivalent (THCE).
Identification number means a unique specification (for example,
model number/serial number combination) that allows someone to
distinguish a particular engine from other similar engines.
Intermediate test speed has the meaning we give in 40 CFR 1065.515.
Manufacturer has the meaning given in section 216(1) of the Act. In
general, this term includes any person who manufactures an engine,
vehicle, or piece of equipment for sale in the United States or
otherwise introduces a new nonroad engine into commerce in the United
States. This includes importers who import engines, equipment, or
vehicles for resale.
Marine engine means an engine that someone installs or intends to
install on a marine vessel. There are two kinds of marine engines:
(1) Propulsion marine engine means a marine engine that moves a
vessel through the water or directs the vessel's movement.
(2) Auxiliary marine engine means a marine engine not used for
propulsion.
Marine vessel means a vehicle that is capable of operation in water
but is not capable of operation out of water. Amphibious vehicles are
not marine vessels.
Maximum brake power means the maximum brake power an engine
produces at maximum test speed.
Maximum test speed has the meaning we give in 40 CFR 1065.515.
Maximum test torque has the meaning we give in 40 CFR 1065.1001.
Model year means one of the following things:
(1) For freshly manufactured engines (see definition of ``new
nonroad engine,'' paragraph (1)), model year means one of the
following:
(i) Calendar year.
(ii) Your annual new model production period if it is different
than the calendar year. This must include January 1 of the calendar
year for which the model year is named. It may not begin before January
2 of the previous calendar year and it must end by December 31 of the
named calendar year.
(2) For an engine that is converted to a nonroad engine after being
placed into service in a motor vehicle, model year means the calendar
year in which the engine was originally produced (see definition of
``new nonroad engine,'' paragraph (2)).
(3) For a nonroad engine excluded under Sec. 1048.5 that is later
converted to operate in an application that is not excluded, model year
means the calendar year in which the engine was originally produced
(see definition of ``new nonroad engine,'' paragraph (3)).
(4) For engines that are not freshly manufactured but are installed
in new nonroad equipment, model year means the calendar year in which
the engine is installed in the new nonroad equipment. This installation
date is based on the time that final assembly of the equipment is
complete (see definition of ``new nonroad engine,'' paragraph (4)).
(5) For an engine modified by an importer (not the original engine
manufacturer) who has a certificate of conformity for the imported
engine (see definition of ``new nonroad engine,'' paragraph (5)), model
year means one of the following:
(i) The calendar year in which the importer finishes modifying and
labeling the engine.
(ii) Your annual production period for producing engines if it is
different than the calendar year; follow the guidelines in paragraph
(1)(ii) of this definition.
(6) For an engine you import that does not meet the criteria in
paragraphs (1) through (5) of the definition of ``new nonroad engine,''
model year means the calendar year in which the engine manufacturer
completed the original assembly of the engine. In general, this applies
to used equipment that you import without conversion or major
modification.
Motor vehicle has the meaning we give in 40 CFR 85.1703(a). In
general, motor vehicle means a self-propelled vehicle that can
transport one or more people or any material, but doesn't include any
of the following:
(1) Vehicles having a maximum ground speed over level, paved
surfaces no higher than 40 km per hour (25 miles per hour).
(2) Vehicles that lack features usually needed for safe, practical
use on streets or highways--for example, safety features required by
law, a reverse gear (except for motorcycles), or a differential.
(3) Vehicles whose operation on streets or highways would be
unsafe, impractical, or highly unlikely. Examples are vehicles with
tracks instead of wheels, very large size, or features associated with
military vehicles, such as armor or weaponry.
New nonroad engine means any of the following things:
(1) A freshly manufactured nonroad engine for which the ultimate
buyer has never received the equitable or legal title. This kind of
vehicle might commonly be thought of as ``brand new.'' In the case of
this paragraph (1), the engine is no longer new when the ultimate buyer
receives this title or the product is placed into service, whichever
comes first.
(2) An engine originally manufactured as a motor vehicle engine
that is later intended to be used in a piece of nonroad equipment. In
this case, the engine is no longer a motor vehicle engine and becomes a
``new nonroad engine''. The engine is no longer new when it is placed
into nonroad service.
(3) A nonroad engine that has been previously placed into service
in an application we exclude under Sec. 1048.5, where that engine is
installed in a piece of equipment for which these exclusions do not
apply. The engine is no longer new when it is placed into nonroad
service. For example, this would apply to a stationary engine that is
no longer used in a stationary application.
(4) An engine not covered by paragraphs (1) through (3) of this
definition that is intended to be installed in new nonroad equipment.
The engine is no longer new when the ultimate buyer receives a title
for the equipment or the product is placed into service, whichever
comes first. This generally includes installation of used engines in
new equipment.
(5) An imported nonroad engine covered by a certificate of
conformity issued under this part, where someone other than the
original engine
[[Page 68367]]
manufacturer modifies the engine after its initial assembly and holds
the certificate. The engine is no longer new when it is placed into
nonroad service.
(6) An imported nonroad engine that is not covered by a certificate
of conformity issued under this part at the time of importation. This
addresses uncertified engines and vehicles that have been placed into
service in other countries and that someone seeks to import into the
United States. Importation of this kind of new nonroad engine (or
vehicle containing such an engine) is generally prohibited by 40 CFR
part 1068.
New nonroad equipment means either of the following things:
(1) A nonroad vehicle or other piece of equipment for which the
ultimate buyer has never received the equitable or legal title. The
product is no longer new when the ultimate buyer receives this title or
the product is placed into service, whichever comes first.
(2) An imported nonroad piece of equipment with an engine not
covered by a certificate of conformity issued under this part at the
time of importation and manufactured after the date for applying the
requirements of this part.
Noncommercial fuel means a fuel that is not marketed or sold as a
commercial product. For example, this includes methane produced and
released from landfills or oil wells.
Noncompliant engine means an engine that was originally covered by
a certificate of conformity, but is not in the certified configuration
or otherwise does not comply with the conditions of the certificate.
Nonconforming engine means an engine not covered by a certificate
of conformity that would otherwise be subject to emission standards.
Nonmethane hydrocarbon means the difference between the emitted
mass of total hydrocarbons and the emitted mass of methane.
Nonroad means relating to nonroad engines or equipment that
includes nonroad engines.
Nonroad engine has the meaning given in 40 CFR 1068.30. In general
this means all internal-combustion engines except motor vehicle
engines, stationary engines, or engines used solely for competition.
This part does not apply to all nonroad engines (see Sec. 1048.5).
Off-highway motorcycle has the meaning we give in 40 CFR 1051.801.
(Note: highway motorcycles are regulated under 40 CFR part 86.)
Oxides of nitrogen has the meaning given it in 40 CFR part 1065
Placed into service means used for its intended purpose.
Point of first retail sale means the location at which the retail
sale occurs. This generally means a dealership.
Revoke means to discontinue the certificate for an engine family.
If we revoke a certificate, you must apply for a new certificate before
continuing to produce the affected vehicles or engines. This does not
apply to vehicles or engines you no longer possess.
Round means to round numbers according to ASTM E29-02 (incorporated
by reference in Sec. 1048.810), unless otherwise specified.
Scheduled maintenance means adjusting, repairing, removing,
disassembling, cleaning, or replacing components or systems that is
periodically needed to keep a part from failing or malfunctioning. It
also may mean actions you expect are necessary to correct an overt
indication of failure or malfunction for which periodic maintenance is
not appropriate.
Severe-duty application includes concrete saws, concrete pumps, and
any other application where an engine manufacturer can provide clear
evidence that the majority of installations need air-cooled engines as
a result of operation in a severe-duty environment.
Severe-duty engine means an engine from an engine family in which
the majority of engines are installed in severe-duty applications.
Small-volume engine manufacturer means a company with fewer than
200 employees. This includes any employees working for parent or
subsidiary companies.
Snowmobile has the meaning we give in 40 CFR 1051.801.
Spark-ignition means relating to a gasoline-fueled engine or any
other type of engine with a spark plug (or other sparking device) and
with operating characteristics significantly similar to the theoretical
Otto combustion cycle. Spark-ignition engines usually use a throttle to
regulate intake air flow to control power during normal operation.
Stationary engine means an internal combustion engine that is
neither a nonroad engine, nor a motor-vehicle engine, nor an engine
used solely for competition (see the definition of nonroad engine in 40
CFR 1068.30). In general this includes fixed engines and all portable
or transportable engines that stay in a single site at a building,
structure, facility, or installation for at least a full year; this
does not include an engine installed in equipment that has the ability
to propel itself. For year-round sources, a full year is 12 consecutive
months. For seasonal sources, a full year is a full annual operating
period of at least three months. A seasonal source is a site with
engines operating only part of the year for at least two consecutive
years. If you replace an engine with one that does the same or similar
work in the same place, you may apply the previous engine's service to
your calculation for residence time. If you move a stationary engine
anytime in its life after it has been in place for at least a full
year, it becomes a nonroad engine subject to emission standards unless
it stays at the new location for a full year.
Stoichiometry means the proportion of a mixture of air and fuel
such that the fuel is fully oxidized with no remaining oxygen. For
example, stoichiometric combustion in gasoline engines typically occurs
at an air-fuel mass ratio of about 14.7.
Suspend means to temporarily discontinue the certificate for an
engine family. If we suspend a certificate, you may not sell vehicles
or engines from that engine family unless we reinstate the certificate
or approve a new one.
Test engine means an engine in a test sample.
Test sample means the collection of engines selected from the
population of an engine family for emission testing.
Total hydrocarbon means the combined mass organic compounds
measured by our total hydrocarbon test procedure, expressed as a
hydrocarbon with a hydrogen-to-carbon mass ratio of 1.85:1.
Total hydrocarbon equivalent means the sum of the carbon mass
contributions of non-oxygenated hydrocarbons, alcohols and aldehydes,
or other organic compounds that are measured separately as contained in
a gas sample, expressed as petroleum-fueled engine hydrocarbons. The
hydrogen-to-carbon ratio of the equivalent hydrocarbon is 1.85:1.
Tier 1 means relating to the emission standards and other
requirements that apply beginning with the 2004 model year.
Tier 2 means relating to the emission standards and other
requirements that apply beginning with the 2007 model year.
Ultimate buyer means ultimate purchaser.
Ultimate purchaser means, with respect to any new nonroad equipment
or new nonroad engine, the first person who in good faith purchases
such new nonroad equipment or new nonroad engine for purposes other
than resale.
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the
[[Page 68368]]
U.S. Virgin Islands, and the Trust Territory of the Pacific Islands.
Upcoming model year means for an engine family the model year after
the one currently in production.
U.S.-directed production volume means the number of engine units,
subject to the requirements of this part, produced by a manufacturer
for which the manufacturer has a reasonable assurance that sale was or
will be made to ultimate buyers in the United States.
Useful life means the period during which the engine is designed to
properly function in terms of reliability and fuel consumption, without
being remanufactured, specified as a number of hours of operation or
calendar years. It is the period during which a new nonroad engine is
required to comply with all applicable emission standards. See Sec.
1048.101(g).
Variable-speed engine means an engine that is not a constant-speed
engine.
Void means to invalidate a certificate or an exemption. If we void
a certificate, all the vehicles produced under that engine family for
that model year are considered noncompliant, and you are liable for
each vehicle produced under the certificate and may face civil or
criminal penalties or both. If we void an exemption, all the vehicles
produced under that exemption are considered uncertified (or
nonconforming), and you are liable for each vehicle produced under the
exemption and may face civil or criminal penalties or both. You may not
produce any additional vehicles using the voided exemption.
Volatile liquid fuel means any fuel other than diesel or biodiesel
that is a liquid at atmospheric pressure.
Wide-open throttle means maximum throttle opening. Unless this is
specified at a given speed, it refers to maximum throttle opening at
maximum speed. For electronically controlled or other engines with
multiple possible fueling rates, wide-open throttle also means the
maximum fueling rate at maximum throttle opening under test conditions.
Sec. 1048.805 What symbols, acronyms, and abbreviations does this
part use?
The following symbols, acronyms, and abbreviations apply to this
part:
[deg]
C degrees Celsius.
ASTM American Society for Testing and Materials.
cc cubic centimeters.
CFR Code of Federal Regulations.
cm centimeter.
CO carbon monoxide.
CO2 carbon dioxide.
EPA Environmental Protection Agency.
g/kW-hr grams per kilowatt-hour.
HC hydrocarbon.
ISO International Organization for Standardization.
kPa kilopascals.
kW kilowatts.
LPG liquefied petroleum gas.
m meters.
MIL malfunction-indicator light.
mm Hg millimeters of mercury.
NMHC nonmethane hydrocarbons.
NOX oxides of nitrogen (NO and NO2).
psi pounds per square inch of absolute pressure.
psig pounds per square inch of gauge pressure.
rpm revolutions per minute.
SAE Society of Automotive Engineers.
SI spark-ignition.
THC total hydrocarbon.
THCE total hydrocarbon equivalent.
U.S.C. United States Code.
Sec. 1048.810 What materials does this part reference?
We have incorporated by reference the documents listed in this
section. The Director of the Federal Register approved the
incorporation by reference as prescribed in 5 U.S.C. 552(a) and 1 CFR
part 51. Anyone may inspect copies at the U.S. EPA, Air and Radiation
Docket and Information Center, 1301 Constitution Ave., NW., Room B102,
EPA West Building, Washington, DC 20460 or the Office of the Federal
Register, 800 N. Capitol St., NW., 7th Floor, Suite 700, Washington,
DC.
(a) ASTM material. Table 1 of Sec. 1048.810 lists material from
the American Society for Testing and Materials that we have
incorporated by reference. The first column lists the number and name
of the material. The second column lists the sections of this part
where we reference it. Anyone may purchase copies of these materials
from the American Society for Testing and Materials, 100 Barr Harbor
Dr., West Conshohocken, PA 19428. Table 1 follows:
Table 1 of Sec. 1048.810.--ASTM Materials
------------------------------------------------------------------------
Part 1048
Document number and name reference
------------------------------------------------------------------------
ASTM E29-02, Standard Practice for Using Significant Digits 1048.801
in Test Data to Determine Conformance with Specifications.
------------------------------------------------------------------------
(b) SAE material. Table 2 of Sec. 1048.810 lists material from the
Society of Automotive Engineering that we have incorporated by
reference. The first column lists the number and name of the material.
The second column lists the sections of this part where we reference
it. Anyone may purchase copies of these materials from the Society of
Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.
Table 2 follows:
Table 2 of Sec. 1048.810.--SAE Materials
------------------------------------------------------------------------
Part 1048
Document number and name reference
------------------------------------------------------------------------
SAE J1930, Electrical/Electronic Systems Diagnostic Terms, 1048.135
Definitions, Abbreviations, and Acronyms, May 1998........
------------------------------------------------------------
SAE J2260, Nonmetallic Fuel System Tubing with One or More 1048.105
Layers, November 1996.....................................
------------------------------------------------------------------------
(c) ISO material. Table 3 of Sec. 1048.810 lists material from the
International Organization for Standardization that we have
incorporated by reference. The first column lists the number and name
of the material. The second column lists the section of this part where
we reference it. Anyone may purchase copies of these materials from the
International Organization for Standardization, Case Postale 56, CH-
1211 Geneva 20, Switzerland. Table 3 follows:
[[Page 68369]]
Table 3 of Sec. 1048.810.--ISO Materials
------------------------------------------------------------------------
Part 1048
Document number and name reference
------------------------------------------------------------------------
ISO 9141-2 Road vehicles--Diagnostic systems--Part 2: CARB 1048.110
requirements for interchange of digital information,
February 1994.............................................
------------------------------------------------------------
ISO 14230-4 Road vehicles--Diagnostic systems--Keyword 1048.110
Protocol 2000--Part 4: Requirements for emission-related
systems, June 2000........................................
------------------------------------------------------------------------
Sec. 1048.815 How should I request EPA to keep my information
confidential?
(a) Clearly show what you consider confidential by marking,
circling, bracketing, stamping, or some other method. We will store
your confidential information as described in 40 CFR part 2. Also, we
will disclose it only as specified in 40 CFR part 2.
(b) If you send us a second copy without the confidential
information, we will assume it contains nothing confidential whenever
we need to release information from it.
(c) If you send us information without claiming it is confidential,
we may make it available to the public without further notice to you,
as described in 40 CFR 2.204.
Sec. 1048.820 How do I request a hearing?
See 40 CFR part 1068, subpart G, for information related to
hearings.
Appendix I to Part 1048--Large Spark-ignition (SI) Transient Cycle for
Constant-Speed Engines
The following table shows the transient duty-cycle for constant-
speed engines, as described in Sec. 1048.510:
------------------------------------------------------------------------
Normalized Normalized
Time(s) speed torque
(percent) (percent)
------------------------------------------------------------------------
1........................................... 58 5
2........................................... 58 5
3........................................... 58 5
4........................................... 58 5
5........................................... 58 5
6........................................... 58 5
7........................................... 58 5
8........................................... 58 5
9........................................... 58 5
10.......................................... 58 5
11.......................................... 58 5
12.......................................... 65 8
13.......................................... 72 9
14.......................................... 79 12
15.......................................... 86 14
16.......................................... 93 16
17.......................................... 93 16
18.......................................... 93 16
19.......................................... 93 16
20.......................................... 93 16
21.......................................... 93 16
22.......................................... 93 16
23.......................................... 93 16
24.......................................... 93 31
25.......................................... 93 30
26.......................................... 93 27
27.......................................... 93 23
28.......................................... 93 24
29.......................................... 93 21
30.......................................... 93 20
31.......................................... 93 18
32.......................................... 93 16
33.......................................... 93 18
34.......................................... 93 16
35.......................................... 93 17
36.......................................... 93 20
37.......................................... 93 20
38.......................................... 93 22
39.......................................... 93 20
40.......................................... 93 17
41.......................................... 93 17
42.......................................... 93 17
43.......................................... 93 16
44.......................................... 93 18
45.......................................... 93 18
46.......................................... 93 21
47.......................................... 93 21
48.......................................... 93 18
49.......................................... 94 24
50.......................................... 93 28
51.......................................... 93 23
52.......................................... 93 19
53.......................................... 93 20
54.......................................... 93 20
55.......................................... 93 29
56.......................................... 93 23
57.......................................... 93 25
58.......................................... 93 23
59.......................................... 93 23
60.......................................... 93 23
61.......................................... 93 22
62.......................................... 93 21
63.......................................... 93 22
64.......................................... 93 30
65.......................................... 93 33
66.......................................... 93 25
67.......................................... 93 29
68.......................................... 93 27
69.......................................... 93 23
70.......................................... 93 21
71.......................................... 93 21
72.......................................... 93 19
73.......................................... 93 20
74.......................................... 93 24
75.......................................... 93 23
76.......................................... 93 21
77.......................................... 93 44
78.......................................... 93 34
79.......................................... 93 28
80.......................................... 93 37
81.......................................... 93 29
82.......................................... 93 27
83.......................................... 93 33
84.......................................... 93 28
85.......................................... 93 22
86.......................................... 96 30
87.......................................... 95 25
88.......................................... 95 17
89.......................................... 95 13
90.......................................... 95 10
91.......................................... 95 9
92.......................................... 95 8
93.......................................... 95 7
94.......................................... 95 7
95.......................................... 95 6
96.......................................... 95 6
97.......................................... 93 37
98.......................................... 93 35
99.......................................... 93 29
100......................................... 93 23
101......................................... 93 23
102......................................... 93 21
103......................................... 93 20
104......................................... 93 29
105......................................... 93 27
106......................................... 93 26
107......................................... 93 35
108......................................... 93 43
109......................................... 95 35
110......................................... 95 24
111......................................... 95 17
112......................................... 95 13
113......................................... 95 10
114......................................... 95 9
115......................................... 95 8
116......................................... 95 7
117......................................... 95 7
118......................................... 95 6
119......................................... 93 36
120......................................... 93 30
121......................................... 93 25
122......................................... 93 21
123......................................... 93 22
124......................................... 93 19
125......................................... 93 34
126......................................... 93 36
127......................................... 93 31
128......................................... 93 26
129......................................... 93 27
130......................................... 93 22
131......................................... 93 22
132......................................... 93 18
133......................................... 93 18
134......................................... 93 19
135......................................... 93 19
136......................................... 93 23
137......................................... 93 22
138......................................... 93 20
139......................................... 93 23
140......................................... 93 20
141......................................... 93 18
142......................................... 93 18
143......................................... 93 16
144......................................... 93 19
145......................................... 94 25
146......................................... 93 30
[[Page 68370]]
147......................................... 93 29
148......................................... 93 23
149......................................... 93 24
150......................................... 93 22
151......................................... 94 20
152......................................... 93 17
153......................................... 93 16
154......................................... 93 16
155......................................... 93 15
156......................................... 93 17
157......................................... 93 18
158......................................... 93 20
159......................................... 93 21
160......................................... 93 18
161......................................... 93 17
162......................................... 92 54
163......................................... 93 38
164......................................... 93 29
165......................................... 93 24
166......................................... 93 24
167......................................... 93 24
168......................................... 93 23
169......................................... 93 20
170......................................... 93 20
171......................................... 93 18
172......................................... 93 19
173......................................... 93 19
174......................................... 93 16
175......................................... 93 16
176......................................... 93 16
177......................................... 93 18
178......................................... 93 21
179......................................... 93 20
180......................................... 93 20
181......................................... 93 17
182......................................... 93 19
183......................................... 93 17
184......................................... 93 18
185......................................... 93 16
186......................................... 93 16
187......................................... 93 16
188......................................... 93 17
189......................................... 93 16
190......................................... 93 17
191......................................... 93 18
192......................................... 93 17
193......................................... 93 16
194......................................... 93 17
195......................................... 93 17
196......................................... 93 22
197......................................... 93 19
198......................................... 93 19
199......................................... 95 21
200......................................... 95 16
201......................................... 95 12
202......................................... 95 10
203......................................... 96 8
204......................................... 96 7
205......................................... 95 7
206......................................... 96 7
207......................................... 95 6
208......................................... 96 6
209......................................... 96 6
210......................................... 88 6
211......................................... 89 48
212......................................... 93 34
213......................................... 93 27
214......................................... 93 26
215......................................... 93 25
216......................................... 93 22
217......................................... 93 23
218......................................... 93 21
219......................................... 93 21
220......................................... 93 23
221......................................... 93 23
222......................................... 93 23
223......................................... 93 23
224......................................... 93 23
225......................................... 93 22
226......................................... 93 22
227......................................... 93 24
228......................................... 93 23
229......................................... 93 23
230......................................... 93 21
231......................................... 93 20
232......................................... 93 20
233......................................... 93 20
234......................................... 93 22
235......................................... 93 26
236......................................... 93 22
237......................................... 93 20
238......................................... 93 18
239......................................... 93 22
240......................................... 93 20
241......................................... 94 27
242......................................... 93 22
243......................................... 93 23
244......................................... 93 21
245......................................... 93 22
246......................................... 95 22
247......................................... 95 16
248......................................... 95 12
249......................................... 95 10
250......................................... 95 9
251......................................... 95 8
252......................................... 96 7
253......................................... 95 7
254......................................... 95 6
255......................................... 92 42
256......................................... 93 36
257......................................... 93 33
258......................................... 92 60
259......................................... 93 48
260......................................... 93 36
261......................................... 93 30
262......................................... 93 28
263......................................... 93 24
264......................................... 93 24
265......................................... 93 23
266......................................... 93 23
267......................................... 93 25
268......................................... 93 27
269......................................... 93 29
270......................................... 93 26
271......................................... 93 26
272......................................... 93 21
273......................................... 93 23
274......................................... 93 23
275......................................... 94 23
276......................................... 93 40
277......................................... 94 67
278......................................... 93 46
279......................................... 93 38
280......................................... 93 29
281......................................... 93 28
282......................................... 93 27
283......................................... 93 29
284......................................... 93 28
285......................................... 94 34
286......................................... 93 31
287......................................... 93 30
288......................................... 94 42
289......................................... 93 31
290......................................... 93 29
291......................................... 93 27
292......................................... 93 23
293......................................... 93 23
294......................................... 93 20
295......................................... 93 20
296......................................... 93 23
297......................................... 93 23
298......................................... 93 24
299......................................... 93 25
300......................................... 93 20
301......................................... 93 25
302......................................... 93 23
303......................................... 93 23
304......................................... 93 24
305......................................... 93 28
306......................................... 93 23
307......................................... 93 24
308......................................... 93 34
309......................................... 93 31
310......................................... 93 35
311......................................... 93 31
312......................................... 93 32
313......................................... 93 31
314......................................... 93 30
315......................................... 93 23
316......................................... 93 23
317......................................... 93 36
318......................................... 93 32
319......................................... 93 25
320......................................... 93 31
321......................................... 93 33
322......................................... 93 31
323......................................... 93 27
324......................................... 93 24
325......................................... 93 19
326......................................... 96 21
327......................................... 96 16
328......................................... 95 12
329......................................... 95 10
330......................................... 95 8
331......................................... 95 8
332......................................... 95 7
333......................................... 95 7
334......................................... 95 6
335......................................... 95 6
336......................................... 95 6
337......................................... 87 6
338......................................... 57 6
339......................................... 58 6
340......................................... 58 6
341......................................... 58 6
342......................................... 58 6
343......................................... 58 6
344......................................... 58 6
345......................................... 58 6
346......................................... 58 6
347......................................... 58 6
348......................................... 58 6
349......................................... 58 6
350......................................... 58 6
351......................................... 58 6
352......................................... 95 73
353......................................... 93 65
354......................................... 93 52
355......................................... 93 38
356......................................... 93 30
357......................................... 93 31
358......................................... 93 26
359......................................... 93 21
360......................................... 93 22
361......................................... 93 26
362......................................... 93 23
[[Page 68371]]
363......................................... 93 19
364......................................... 93 27
365......................................... 93 42
366......................................... 93 29
367......................................... 94 25
368......................................... 94 26
369......................................... 94 29
370......................................... 93 28
371......................................... 93 23
372......................................... 93 21
373......................................... 93 26
374......................................... 93 23
375......................................... 93 20
376......................................... 94 23
377......................................... 93 18
378......................................... 93 19
379......................................... 93 23
380......................................... 93 19
381......................................... 93 16
382......................................... 93 25
383......................................... 93 22
384......................................... 93 20
385......................................... 93 25
386......................................... 94 28
387......................................... 93 23
388......................................... 93 23
389......................................... 93 25
390......................................... 93 23
391......................................... 93 20
392......................................... 93 19
393......................................... 93 24
394......................................... 93 20
395......................................... 93 18
396......................................... 93 21
397......................................... 95 22
398......................................... 96 16
399......................................... 96 12
400......................................... 95 10
401......................................... 96 9
402......................................... 95 8
403......................................... 96 7
404......................................... 96 7
405......................................... 96 6
406......................................... 96 6
407......................................... 95 6
408......................................... 91 6
409......................................... 58 6
410......................................... 58 6
411......................................... 58 6
412......................................... 58 6
413......................................... 58 6
414......................................... 58 6
415......................................... 58 6
416......................................... 58 6
417......................................... 58 6
418......................................... 58 6
419......................................... 58 6
420......................................... 58 6
421......................................... 58 6
422......................................... 58 6
423......................................... 58 6
424......................................... 58 6
425......................................... 58 6
426......................................... 58 6
427......................................... 58 6
428......................................... 58 6
429......................................... 58 6
430......................................... 58 6
431......................................... 58 6
432......................................... 58 6
433......................................... 58 6
434......................................... 58 6
435......................................... 58 6
436......................................... 58 6
437......................................... 58 6
438......................................... 58 6
439......................................... 58 6
440......................................... 58 6
441......................................... 58 6
442......................................... 58 6
443......................................... 93 66
444......................................... 93 48
445......................................... 93 40
446......................................... 93 34
447......................................... 93 28
448......................................... 93 23
449......................................... 93 28
450......................................... 93 27
451......................................... 93 23
452......................................... 93 19
453......................................... 93 25
454......................................... 93 24
455......................................... 93 22
456......................................... 93 31
457......................................... 93 36
458......................................... 93 28
459......................................... 93 25
460......................................... 93 35
461......................................... 93 34
462......................................... 93 29
463......................................... 93 37
464......................................... 93 36
465......................................... 93 38
466......................................... 93 31
467......................................... 93 29
468......................................... 93 34
469......................................... 93 36
470......................................... 93 34
471......................................... 93 31
472......................................... 93 26
473......................................... 93 21
474......................................... 94 16
475......................................... 96 19
476......................................... 96 15
477......................................... 95 11
478......................................... 96 10
479......................................... 95 8
480......................................... 95 7
481......................................... 95 7
482......................................... 96 7
483......................................... 96 6
484......................................... 96 6
485......................................... 95 6
486......................................... 85 6
487......................................... 56 74
488......................................... 93 52
489......................................... 93 42
490......................................... 93 36
491......................................... 93 35
492......................................... 93 33
493......................................... 93 38
494......................................... 93 40
495......................................... 93 29
496......................................... 93 23
497......................................... 93 23
498......................................... 93 24
499......................................... 93 24
500......................................... 93 20
501......................................... 93 19
502......................................... 93 16
503......................................... 93 21
504......................................... 93 23
505......................................... 93 24
506......................................... 93 22
507......................................... 93 18
508......................................... 93 21
509......................................... 95 18
510......................................... 95 20
511......................................... 95 15
512......................................... 96 11
513......................................... 95 10
514......................................... 96 8
515......................................... 95 7
516......................................... 95 7
517......................................... 95 7
518......................................... 95 6
519......................................... 96 6
520......................................... 96 6
521......................................... 83 6
522......................................... 56 6
523......................................... 58 6
524......................................... 72 54
525......................................... 94 51
526......................................... 93 42
527......................................... 93 42
528......................................... 93 31
529......................................... 93 25
530......................................... 93 21
531......................................... 93 17
532......................................... 93 15
533......................................... 93 15
534......................................... 93 16
535......................................... 93 15
536......................................... 93 14
537......................................... 93 15
538......................................... 93 16
539......................................... 94 15
540......................................... 93 45
541......................................... 93 45
542......................................... 93 41
543......................................... 93 33
544......................................... 93 26
545......................................... 93 21
546......................................... 93 20
547......................................... 93 17
548......................................... 93 16
549......................................... 93 17
550......................................... 93 16
551......................................... 93 14
552......................................... 93 16
553......................................... 93 15
554......................................... 93 14
555......................................... 93 16
556......................................... 93 15
557......................................... 93 14
558......................................... 93 13
559......................................... 93 14
560......................................... 93 14
561......................................... 93 15
562......................................... 93 17
563......................................... 93 17
564......................................... 93 22
565......................................... 93 22
566......................................... 93 19
567......................................... 93 19
568......................................... 93 20
569......................................... 93 18
570......................................... 93 20
571......................................... 93 20
572......................................... 93 42
573......................................... 93 32
574......................................... 93 25
575......................................... 93 26
576......................................... 93 23
577......................................... 93 21
578......................................... 93 23
[[Page 68372]]
579......................................... 93 19
580......................................... 93 21
581......................................... 93 20
582......................................... 93 20
583......................................... 93 20
584......................................... 93 18
585......................................... 93 18
586......................................... 93 21
587......................................... 93 19
588......................................... 93 21
589......................................... 93 19
590......................................... 93 19
591......................................... 93 18
592......................................... 93 18
593......................................... 93 17
594......................................... 93 16
595......................................... 93 16
596......................................... 93 15
597......................................... 93 16
598......................................... 93 19
599......................................... 93 52
600......................................... 93 45
601......................................... 95 39
602......................................... 95 39
603......................................... 95 39
604......................................... 95 39
605......................................... 94 30
606......................................... 95 30
607......................................... 95 29
608......................................... 95 24
609......................................... 94 30
610......................................... 95 28
611......................................... 94 25
612......................................... 94 29
613......................................... 95 32
614......................................... 95 33
615......................................... 95 44
616......................................... 99 37
617......................................... 98 27
618......................................... 98 19
619......................................... 98 13
620......................................... 98 11
621......................................... 98 9
622......................................... 98 7
623......................................... 98 7
624......................................... 98 6
625......................................... 98 6
626......................................... 98 6
627......................................... 98 5
628......................................... 69 6
629......................................... 49 5
630......................................... 51 5
631......................................... 51 5
632......................................... 51 5
633......................................... 51 6
634......................................... 51 6
635......................................... 51 6
636......................................... 51 6
637......................................... 51 5
638......................................... 51 5
639......................................... 51 5
640......................................... 51 5
641......................................... 51 6
642......................................... 51 6
643......................................... 51 6
644......................................... 51 6
645......................................... 51 5
646......................................... 51 6
647......................................... 51 5
648......................................... 51 6
649......................................... 51 5
650......................................... 96 35
651......................................... 95 29
652......................................... 95 26
653......................................... 95 31
654......................................... 95 34
655......................................... 95 29
656......................................... 95 29
657......................................... 95 30
658......................................... 95 24
659......................................... 95 19
660......................................... 95 23
661......................................... 95 21
662......................................... 95 22
663......................................... 95 19
664......................................... 95 18
665......................................... 95 20
666......................................... 94 60
667......................................... 95 48
668......................................... 95 39
669......................................... 95 36
670......................................... 95 27
671......................................... 95 22
672......................................... 95 19
673......................................... 95 22
674......................................... 95 19
675......................................... 94 17
676......................................... 95 27
677......................................... 95 24
678......................................... 98 19
679......................................... 98 19
680......................................... 98 14
681......................................... 98 11
682......................................... 98 9
683......................................... 98 8
684......................................... 98 7
685......................................... 98 6
686......................................... 98 6
687......................................... 98 6
688......................................... 98 6
689......................................... 98 5
690......................................... 81 5
691......................................... 49 5
692......................................... 78 48
693......................................... 95 37
694......................................... 95 31
695......................................... 94 32
696......................................... 94 34
697......................................... 95 29
698......................................... 95 25
699......................................... 94 26
700......................................... 95 28
701......................................... 95 27
702......................................... 94 28
703......................................... 95 30
704......................................... 95 27
705......................................... 95 26
706......................................... 95 27
707......................................... 95 25
708......................................... 95 26
709......................................... 95 25
710......................................... 95 23
711......................................... 95 20
712......................................... 95 23
713......................................... 95 20
714......................................... 95 18
715......................................... 94 22
716......................................... 95 19
717......................................... 95 23
718......................................... 95 27
719......................................... 95 26
720......................................... 95 23
721......................................... 95 20
722......................................... 99 23
723......................................... 98 20
724......................................... 98 14
725......................................... 98 11
726......................................... 98 9
727......................................... 98 8
728......................................... 98 7
729......................................... 98 6
730......................................... 98 6
731......................................... 98 6
732......................................... 98 5
733......................................... 98 5
734......................................... 73 6
735......................................... 49 5
736......................................... 50 77
737......................................... 95 39
738......................................... 95 30
739......................................... 95 28
740......................................... 94 31
741......................................... 95 36
742......................................... 95 36
743......................................... 95 30
744......................................... 95 26
745......................................... 95 27
746......................................... 95 22
747......................................... 95 18
748......................................... 95 19
749......................................... 95 25
750......................................... 94 25
751......................................... 95 21
752......................................... 95 22
753......................................... 95 27
754......................................... 95 27
755......................................... 95 27
756......................................... 95 24
757......................................... 94 20
758......................................... 94 23
759......................................... 94 26
760......................................... 95 25
761......................................... 95 25
762......................................... 95 21
763......................................... 95 28
764......................................... 94 39
765......................................... 95 32
766......................................... 95 24
767......................................... 95 19
768......................................... 98 20
769......................................... 98 17
770......................................... 98 12
771......................................... 98 10
772......................................... 98 8
773......................................... 98 7
774......................................... 98 6
775......................................... 98 6
776......................................... 95 61
777......................................... 94 51
778......................................... 95 40
779......................................... 94 35
780......................................... 94 36
781......................................... 94 32
782......................................... 95 24
783......................................... 94 19
784......................................... 94 19
785......................................... 95 19
786......................................... 95 19
787......................................... 94 18
788......................................... 94 20
789......................................... 94 23
790......................................... 94 22
791......................................... 95 23
792......................................... 94 20
793......................................... 94 18
794......................................... 95 16
[[Page 68373]]
795......................................... 95 17
796......................................... 94 16
797......................................... 94 16
798......................................... 94 17
799......................................... 94 18
800......................................... 94 21
801......................................... 95 21
802......................................... 94 19
803......................................... 95 18
804......................................... 94 19
805......................................... 95 22
806......................................... 95 21
807......................................... 95 19
808......................................... 94 20
809......................................... 94 22
810......................................... 94 22
811......................................... 94 22
812......................................... 95 23
813......................................... 94 22
814......................................... 95 22
815......................................... 95 19
816......................................... 95 16
817......................................... 95 14
818......................................... 95 18
819......................................... 95 18
820......................................... 94 20
821......................................... 94 22
822......................................... 94 19
823......................................... 95 18
824......................................... 95 17
825......................................... 95 19
826......................................... 95 19
827......................................... 95 19
828......................................... 94 19
829......................................... 94 21
830......................................... 94 19
831......................................... 94 17
832......................................... 94 18
833......................................... 94 21
834......................................... 94 19
835......................................... 95 18
836......................................... 95 19
837......................................... 95 17
838......................................... 94 15
839......................................... 94 17
840......................................... 95 19
841......................................... 94 22
842......................................... 94 21
843......................................... 94 18
844......................................... 94 16
845......................................... 95 14
846......................................... 95 14
847......................................... 94 19
848......................................... 95 20
849......................................... 95 23
850......................................... 98 23
851......................................... 98 22
852......................................... 98 16
853......................................... 98 12
854......................................... 98 9
855......................................... 98 8
856......................................... 98 7
857......................................... 98 6
858......................................... 98 6
859......................................... 98 6
860......................................... 98 5
861......................................... 98 5
862......................................... 80 5
863......................................... 49 5
864......................................... 51 5
865......................................... 51 5
866......................................... 51 6
867......................................... 51 6
868......................................... 51 6
869......................................... 51 6
870......................................... 51 5
871......................................... 51 6
872......................................... 51 7
873......................................... 96 45
874......................................... 94 44
875......................................... 94 34
876......................................... 94 41
877......................................... 95 44
878......................................... 94 32
879......................................... 95 26
880......................................... 94 20
881......................................... 95 29
882......................................... 95 27
883......................................... 95 21
884......................................... 95 34
885......................................... 95 31
886......................................... 94 26
887......................................... 95 22
888......................................... 95 23
889......................................... 95 19
890......................................... 94 18
891......................................... 94 20
892......................................... 94 26
893......................................... 95 29
894......................................... 94 32
895......................................... 95 26
896......................................... 95 34
897......................................... 95 30
898......................................... 95 24
899......................................... 95 19
900......................................... 94 17
901......................................... 94 16
902......................................... 98 19
903......................................... 98 17
904......................................... 98 12
905......................................... 98 10
906......................................... 98 8
907......................................... 98 7
908......................................... 98 6
909......................................... 98 6
910......................................... 98 6
911......................................... 98 5
912......................................... 98 5
913......................................... 98 5
914......................................... 69 5
915......................................... 49 5
916......................................... 51 5
917......................................... 51 6
918......................................... 51 6
919......................................... 69 75
920......................................... 95 70
921......................................... 95 57
922......................................... 94 49
923......................................... 94 38
924......................................... 95 43
925......................................... 94 51
926......................................... 94 41
927......................................... 98 42
928......................................... 95 89
929......................................... 95 66
930......................................... 94 52
931......................................... 95 41
932......................................... 95 34
933......................................... 95 34
934......................................... 94 30
935......................................... 94 30
936......................................... 95 29
937......................................... 94 28
938......................................... 95 24
939......................................... 94 34
940......................................... 95 26
941......................................... 94 36
942......................................... 95 27
943......................................... 95 25
944......................................... 95 26
945......................................... 94 21
946......................................... 94 19
947......................................... 98 21
948......................................... 93 53
949......................................... 94 45
950......................................... 94 35
951......................................... 95 28
952......................................... 95 23
953......................................... 95 20
954......................................... 95 17
955......................................... 94 19
956......................................... 94 18
957......................................... 94 18
958......................................... 94 18
959......................................... 94 19
960......................................... 97 17
961......................................... 98 19
962......................................... 98 14
963......................................... 98 11
964......................................... 98 9
965......................................... 98 7
966......................................... 98 7
967......................................... 98 6
968......................................... 98 6
969......................................... 98 6
970......................................... 98 5
971......................................... 98 5
972......................................... 82 5
973......................................... 49 5
974......................................... 51 6
975......................................... 51 6
976......................................... 51 6
977......................................... 51 5
978......................................... 51 6
979......................................... 72 58
980......................................... 94 36
981......................................... 95 28
982......................................... 95 24
983......................................... 95 25
984......................................... 95 26
985......................................... 94 30
986......................................... 94 26
987......................................... 95 34
988......................................... 95 57
989......................................... 95 45
990......................................... 94 37
991......................................... 95 34
992......................................... 95 27
993......................................... 95 27
994......................................... 95 29
995......................................... 98 22
996......................................... 94 84
997......................................... 94 74
998......................................... 95 62
999......................................... 94 51
1000........................................ 95 50
1001........................................ 95 81
1002........................................ 94 65
1003........................................ 95 49
1004........................................ 94 56
1005........................................ 95 65
1006........................................ 94 59
1007........................................ 99 58
1008........................................ 98 41
1009........................................ 98 27
1010........................................ 98 19
[[Page 68374]]
1011........................................ 98 13
1012........................................ 98 11
1013........................................ 98 9
1014........................................ 98 8
1015........................................ 98 7
1016........................................ 98 6
1017........................................ 98 6
1018........................................ 98 6
1019........................................ 71 6
1020........................................ 49 5
1021........................................ 51 6
1022........................................ 51 6
1023........................................ 51 6
1024........................................ 51 6
1025........................................ 51 6
1026........................................ 51 6
1027........................................ 51 6
1028........................................ 51 6
1029........................................ 51 6
1030........................................ 51 6
1031........................................ 51 5
1032........................................ 51 6
1033........................................ 51 5
1034........................................ 51 6
1035........................................ 51 6
1036........................................ 51 6
1037........................................ 51 5
1038........................................ 51 5
1039........................................ 51 6
1040........................................ 51 6
1041........................................ 69 59
1042........................................ 94 48
1043........................................ 95 34
1044........................................ 95 29
1045........................................ 95 26
1046........................................ 94 27
1047........................................ 95 31
1048........................................ 95 26
1049........................................ 95 34
1050........................................ 95 29
1051........................................ 95 31
1052........................................ 95 29
1053........................................ 95 35
1054........................................ 95 38
1055........................................ 94 41
1056........................................ 95 28
1057........................................ 95 36
1058........................................ 94 30
1059........................................ 94 26
1060........................................ 94 33
1061........................................ 95 34
1062........................................ 95 27
1063........................................ 98 26
1064........................................ 98 19
1065........................................ 98 13
1066........................................ 98 11
1067........................................ 98 9
1068........................................ 98 7
1069........................................ 98 7
1070........................................ 98 6
1071........................................ 98 6
1072........................................ 98 6
1073........................................ 98 5
1074........................................ 89 6
1075........................................ 49 5
1076........................................ 51 6
1077........................................ 51 6
1078........................................ 51 6
1079........................................ 51 6
1080........................................ 51 6
1081........................................ 51 6
1082........................................ 51 6
1083........................................ 50 6
1084........................................ 51 6
1085........................................ 51 6
1086........................................ 51 6
1087........................................ 51 6
1088........................................ 51 6
1089........................................ 51 6
1090........................................ 51 6
1091........................................ 56 74
1092........................................ 95 56
1093........................................ 94 49
1094........................................ 95 47
1095........................................ 94 43
1096........................................ 94 33
1097........................................ 95 50
1098........................................ 94 40
1099........................................ 95 33
1100........................................ 95 24
1101........................................ 94 22
1102........................................ 94 22
1103........................................ 94 25
1104........................................ 95 27
1105........................................ 95 32
1106........................................ 94 29
1107........................................ 94 26
1108........................................ 94 26
1109........................................ 94 24
1110........................................ 98 52
1111........................................ 94 41
1112........................................ 99 35
1113........................................ 95 58
1114........................................ 95 58
1115........................................ 98 57
1116........................................ 98 38
1117........................................ 98 26
1118........................................ 93 63
1119........................................ 94 59
1120........................................ 98 100
1121........................................ 94 73
1122........................................ 98 53
1123........................................ 94 76
1124........................................ 95 61
1125........................................ 94 49
1126........................................ 94 37
1127........................................ 97 50
1128........................................ 98 36
1129........................................ 98 25
1130........................................ 98 18
1131........................................ 98 12
1132........................................ 98 10
1133........................................ 98 8
1134........................................ 98 7
1135........................................ 98 7
1136........................................ 98 6
1137........................................ 98 6
1138........................................ 98 6
1139........................................ 80 6
1140........................................ 49 6
1141........................................ 78 61
1142........................................ 95 50
1143........................................ 94 43
1144........................................ 94 42
1145........................................ 94 31
1146........................................ 95 30
1147........................................ 95 34
1148........................................ 95 28
1149........................................ 95 27
1150........................................ 94 27
1151........................................ 95 31
1152........................................ 95 42
1153........................................ 94 41
1154........................................ 95 37
1155........................................ 95 43
1156........................................ 95 34
1157........................................ 95 31
1158........................................ 95 27
1159........................................ 95 23
1160........................................ 95 27
1161........................................ 96 38
1162........................................ 95 40
1163........................................ 95 39
1164........................................ 95 26
1165........................................ 95 33
1166........................................ 94 28
1167........................................ 94 34
1168........................................ 98 73
1169........................................ 95 49
1170........................................ 95 51
1171........................................ 94 55
1172........................................ 95 48
1173........................................ 95 35
1174........................................ 95 39
1175........................................ 95 39
1176........................................ 94 41
1177........................................ 95 30
1178........................................ 95 23
1179........................................ 94 19
1180........................................ 95 25
1181........................................ 94 29
1182........................................ 98 27
1183........................................ 95 89
1184........................................ 95 74
1185........................................ 94 60
1186........................................ 94 48
1187........................................ 94 41
1188........................................ 94 29
1189........................................ 94 24
1190........................................ 95 19
1191........................................ 94 21
1192........................................ 95 29
1193........................................ 95 28
1194........................................ 95 27
1195........................................ 94 23
1196........................................ 95 25
1197........................................ 95 26
1198........................................ 94 22
1199........................................ 95 19
1200........................................ 94 17
------------------------------------------------------------------------
Appendix II to Part 1048--Large Spark-ignition (SI) Composite Transient
Cycle
The following table shows the transient duty-cycle for engines that
are not constant-speed engines, as described in Sec. 1048.510:
------------------------------------------------------------------------
Normalized Normalized
Time(s) speed torque
(percent) (percent)
------------------------------------------------------------------------
0........................................... 0 0
1........................................... 0 0
2........................................... 0 0
3........................................... 0 0
4........................................... 0 0
5........................................... 0 0
6........................................... 0 0
7........................................... 0 0
8........................................... 0 0
9........................................... 1 8
10.......................................... 6 54
11.......................................... 8 61
12.......................................... 34 59
[[Page 68375]]
13.......................................... 22 46
14.......................................... 5 51
15.......................................... 18 51
16.......................................... 31 50
17.......................................... 30 56
18.......................................... 31 49
19.......................................... 25 66
20.......................................... 58 55
21.......................................... 43 31
22.......................................... 16 45
23.......................................... 24 38
24.......................................... 24 27
25.......................................... 30 33
26.......................................... 45 65
27.......................................... 50 49
28.......................................... 23 42
29.......................................... 13 42
30.......................................... 9 45
31.......................................... 23 30
32.......................................... 37 45
33.......................................... 44 50
34.......................................... 49 52
35.......................................... 55 49
36.......................................... 61 46
37.......................................... 66 38
38.......................................... 42 33
39.......................................... 17 41
40.......................................... 17 37
41.......................................... 7 50
42.......................................... 20 32
43.......................................... 5 55
44.......................................... 30 42
45.......................................... 44 53
46.......................................... 45 56
47.......................................... 41 52
48.......................................... 24 41
49.......................................... 15 40
50.......................................... 11 44
51.......................................... 32 31
52.......................................... 38 54
53.......................................... 38 47
54.......................................... 9 55
55.......................................... 10 50
56.......................................... 33 55
57.......................................... 48 56
58.......................................... 49 47
59.......................................... 33 44
60.......................................... 52 43
61.......................................... 55 43
62.......................................... 59 38
63.......................................... 44 28
64.......................................... 24 37
65.......................................... 12 44
66.......................................... 9 47
67.......................................... 12 52
68.......................................... 34 21
69.......................................... 29 44
70.......................................... 44 54
71.......................................... 54 62
72.......................................... 62 57
73.......................................... 72 56
74.......................................... 88 71
75.......................................... 100 69
76.......................................... 100 34
77.......................................... 100 42
78.......................................... 100 54
79.......................................... 100 58
80.......................................... 100 38
81.......................................... 83 17
82.......................................... 61 15
83.......................................... 43 22
84.......................................... 24 35
85.......................................... 16 39
86.......................................... 15 45
87.......................................... 32 34
88.......................................... 14 42
89.......................................... 8 48
90.......................................... 5 51
91.......................................... 10 41
92.......................................... 12 37
93.......................................... 4 47
94.......................................... 3 49
95.......................................... 3 50
96.......................................... 4 49
97.......................................... 4 48
98.......................................... 8 43
99.......................................... 2 51
100......................................... 5 46
101......................................... 8 41
102......................................... 4 47
103......................................... 3 49
104......................................... 6 45
105......................................... 3 48
106......................................... 10 42
107......................................... 18 27
108......................................... 3 50
109......................................... 11 41
110......................................... 34 29
111......................................... 51 57
112......................................... 67 63
113......................................... 61 32
114......................................... 44 31
115......................................... 48 54
116......................................... 69 65
117......................................... 85 65
118......................................... 81 29
119......................................... 74 21
120......................................... 62 23
121......................................... 76 58
122......................................... 96 75
123......................................... 100 77
124......................................... 100 27
125......................................... 100 79
126......................................... 100 79
127......................................... 100 81
128......................................... 100 57
129......................................... 99 52
130......................................... 81 35
131......................................... 69 29
132......................................... 47 22
133......................................... 34 28
134......................................... 27 37
135......................................... 83 60
136......................................... 100 74
137......................................... 100 7
138......................................... 100 2
139......................................... 70 18
140......................................... 23 39
141......................................... 5 54
142......................................... 11 40
143......................................... 11 34
144......................................... 11 41
145......................................... 19 25
146......................................... 16 32
147......................................... 20 31
148......................................... 21 38
149......................................... 21 42
150......................................... 9 51
151......................................... 4 49
152......................................... 2 51
153......................................... 1 58
154......................................... 21 57
155......................................... 29 47
156......................................... 33 45
157......................................... 16 49
158......................................... 38 45
159......................................... 37 43
160......................................... 35 42
161......................................... 39 43
162......................................... 51 49
163......................................... 59 55
164......................................... 65 54
165......................................... 76 62
166......................................... 84 59
167......................................... 83 29
168......................................... 67 35
169......................................... 84 54
170......................................... 90 58
171......................................... 93 43
172......................................... 90 29
173......................................... 66 19
174......................................... 52 16
175......................................... 49 17
176......................................... 56 38
177......................................... 73 71
178......................................... 86 80
179......................................... 96 75
180......................................... 89 27
181......................................... 66 17
182......................................... 50 18
183......................................... 36 25
184......................................... 36 24
185......................................... 38 40
186......................................... 40 50
187......................................... 27 48
188......................................... 19 48
189......................................... 23 50
190......................................... 19 45
191......................................... 6 51
192......................................... 24 48
193......................................... 49 67
194......................................... 47 49
195......................................... 22 44
196......................................... 25 40
197......................................... 38 54
198......................................... 43 55
199......................................... 40 52
200......................................... 14 49
201......................................... 11 45
202......................................... 7 48
203......................................... 26 41
204......................................... 41 59
205......................................... 53 60
206......................................... 44 54
207......................................... 22 40
208......................................... 24 41
209......................................... 32 53
210......................................... 44 74
211......................................... 57 25
212......................................... 22 49
213......................................... 29 45
214......................................... 19 37
215......................................... 14 43
216......................................... 36 40
217......................................... 43 63
218......................................... 42 49
219......................................... 15 50
220......................................... 19 44
221......................................... 47 59
222......................................... 67 80
223......................................... 76 74
224......................................... 87 66
225......................................... 98 61
226......................................... 100 38
227......................................... 97 27
228......................................... 100 53
[[Page 68376]]
229......................................... 100 72
230......................................... 100 49
231......................................... 100 4
232......................................... 100 13
233......................................... 87 15
234......................................... 53 26
235......................................... 33 27
236......................................... 39 19
237......................................... 51 33
238......................................... 67 54
239......................................... 83 60
240......................................... 95 52
241......................................... 100 50
242......................................... 100 36
243......................................... 100 25
244......................................... 85 16
245......................................... 62 16
246......................................... 40 26
247......................................... 56 39
248......................................... 81 75
249......................................... 98 86
250......................................... 100 76
251......................................... 100 51
252......................................... 100 78
253......................................... 100 83
254......................................... 100 100
255......................................... 100 66
256......................................... 100 85
257......................................... 100 72
258......................................... 100 45
259......................................... 98 58
260......................................... 60 30
261......................................... 43 32
262......................................... 71 36
263......................................... 44 32
264......................................... 24 38
265......................................... 42 17
266......................................... 22 51
267......................................... 13 53
268......................................... 23 45
269......................................... 29 50
270......................................... 28 42
271......................................... 21 55
272......................................... 34 57
273......................................... 44 47
274......................................... 19 46
275......................................... 13 44
276......................................... 25 36
277......................................... 43 51
278......................................... 55 73
279......................................... 68 72
280......................................... 76 63
281......................................... 80 45
282......................................... 83 40
283......................................... 78 26
284......................................... 60 20
285......................................... 47 19
286......................................... 52 25
287......................................... 36 30
288......................................... 40 26
289......................................... 45 34
290......................................... 47 35
291......................................... 42 28
292......................................... 46 38
293......................................... 48 44
294......................................... 68 61
295......................................... 70 47
296......................................... 48 28
297......................................... 42 22
298......................................... 31 29
299......................................... 22 35
300......................................... 28 28
301......................................... 46 46
302......................................... 62 69
303......................................... 76 81
304......................................... 88 85
305......................................... 98 81
306......................................... 100 74
307......................................... 100 13
308......................................... 100 11
309......................................... 100 17
310......................................... 99 3
311......................................... 80 7
312......................................... 62 11
313......................................... 63 11
314......................................... 64 16
315......................................... 69 43
316......................................... 81 67
317......................................... 93 74
318......................................... 100 72
319......................................... 94 27
320......................................... 73 15
321......................................... 40 33
322......................................... 40 52
323......................................... 50 50
324......................................... 11 53
325......................................... 12 45
326......................................... 5 50
327......................................... 1 55
328......................................... 7 55
329......................................... 62 60
330......................................... 80 28
331......................................... 23 37
332......................................... 39 58
333......................................... 47 24
334......................................... 59 51
335......................................... 58 68
336......................................... 36 52
337......................................... 18 42
338......................................... 36 52
339......................................... 59 73
340......................................... 72 85
341......................................... 85 92
342......................................... 99 90
343......................................... 100 72
344......................................... 100 18
345......................................... 100 76
346......................................... 100 64
347......................................... 100 87
348......................................... 100 97
349......................................... 100 84
350......................................... 100 100
351......................................... 100 91
352......................................... 100 83
353......................................... 100 93
354......................................... 100 100
355......................................... 94 43
356......................................... 72 10
357......................................... 77 3
358......................................... 48 2
359......................................... 29 5
360......................................... 59 19
361......................................... 63 5
362......................................... 35 2
363......................................... 24 3
364......................................... 28 2
365......................................... 36 16
366......................................... 54 23
367......................................... 60 10
368......................................... 33 1
369......................................... 23 0
370......................................... 16 0
371......................................... 11 0
372......................................... 20 0
373......................................... 25 2
374......................................... 40 3
375......................................... 33 4
376......................................... 34 5
377......................................... 46 7
378......................................... 57 10
379......................................... 66 11
380......................................... 75 14
381......................................... 79 11
382......................................... 80 16
383......................................... 92 21
384......................................... 99 16
385......................................... 83 2
386......................................... 71 2
387......................................... 69 4
388......................................... 67 4
389......................................... 74 16
390......................................... 86 25
391......................................... 97 28
392......................................... 100 15
393......................................... 83 2
394......................................... 62 4
395......................................... 40 6
396......................................... 49 10
397......................................... 36 5
398......................................... 27 4
399......................................... 29 3
400......................................... 22 2
401......................................... 13 3
402......................................... 37 36
403......................................... 90 26
404......................................... 41 2
405......................................... 25 2
406......................................... 29 2
407......................................... 38 7
408......................................... 50 13
409......................................... 55 10
410......................................... 29 3
411......................................... 24 7
412......................................... 51 16
413......................................... 62 15
414......................................... 72 35
415......................................... 91 74
416......................................... 100 73
417......................................... 100 8
418......................................... 98 11
419......................................... 100 59
420......................................... 100 98
421......................................... 100 99
422......................................... 100 75
423......................................... 100 95
424......................................... 100 100
425......................................... 100 97
426......................................... 100 90
427......................................... 100 86
428......................................... 100 82
429......................................... 97 43
430......................................... 70 16
431......................................... 50 20
432......................................... 42 33
433......................................... 89 64
434......................................... 89 77
435......................................... 99 95
436......................................... 100 41
437......................................... 77 12
438......................................... 29 37
439......................................... 16 41
440......................................... 16 38
441......................................... 15 36
442......................................... 18 44
443......................................... 4 55
444......................................... 24 26
[[Page 68377]]
445......................................... 26 35
446......................................... 15 45
447......................................... 21 39
448......................................... 29 52
449......................................... 26 46
450......................................... 27 50
451......................................... 13 43
452......................................... 25 36
453......................................... 37 57
454......................................... 29 46
455......................................... 17 39
456......................................... 13 41
457......................................... 19 38
458......................................... 28 35
459......................................... 8 51
460......................................... 14 36
461......................................... 17 47
462......................................... 34 39
463......................................... 34 57
464......................................... 11 70
465......................................... 13 51
466......................................... 13 68
467......................................... 38 44
468......................................... 53 67
469......................................... 29 69
470......................................... 19 65
471......................................... 52 45
472......................................... 61 79
473......................................... 29 70
474......................................... 15 53
475......................................... 15 60
476......................................... 52 40
477......................................... 50 61
478......................................... 13 74
479......................................... 46 51
480......................................... 60 73
481......................................... 33 84
482......................................... 31 63
483......................................... 41 42
484......................................... 26 69
485......................................... 23 65
486......................................... 48 49
487......................................... 28 57
488......................................... 16 67
489......................................... 39 48
490......................................... 47 73
491......................................... 35 87
492......................................... 26 73
493......................................... 30 61
494......................................... 34 49
495......................................... 35 66
496......................................... 56 47
497......................................... 49 64
498......................................... 59 64
499......................................... 42 69
500......................................... 6 77
501......................................... 5 59
502......................................... 17 59
503......................................... 45 53
504......................................... 21 62
505......................................... 31 60
506......................................... 53 68
507......................................... 48 79
508......................................... 45 61
509......................................... 51 47
510......................................... 41 48
511......................................... 26 58
512......................................... 21 62
513......................................... 50 52
514......................................... 39 65
515......................................... 23 65
516......................................... 42 62
517......................................... 57 80
518......................................... 66 81
519......................................... 64 62
520......................................... 45 42
521......................................... 33 42
522......................................... 27 57
523......................................... 31 59
524......................................... 41 53
525......................................... 45 72
526......................................... 48 73
527......................................... 46 90
528......................................... 56 76
529......................................... 64 76
530......................................... 69 64
531......................................... 72 59
532......................................... 73 58
533......................................... 71 56
534......................................... 66 48
535......................................... 61 50
536......................................... 55 56
537......................................... 52 52
538......................................... 54 49
539......................................... 61 50
540......................................... 64 54
541......................................... 67 54
542......................................... 68 52
543......................................... 60 53
544......................................... 52 50
545......................................... 45 49
546......................................... 38 45
547......................................... 32 45
548......................................... 26 53
549......................................... 23 56
550......................................... 30 49
551......................................... 33 55
552......................................... 35 59
553......................................... 33 65
554......................................... 30 67
555......................................... 28 59
556......................................... 25 58
557......................................... 23 56
558......................................... 22 57
559......................................... 19 63
560......................................... 14 63
561......................................... 31 61
562......................................... 35 62
563......................................... 21 80
564......................................... 28 65
565......................................... 7 74
566......................................... 23 54
567......................................... 38 54
568......................................... 14 78
569......................................... 38 58
570......................................... 52 75
571......................................... 59 81
572......................................... 66 69
573......................................... 54 44
574......................................... 48 34
575......................................... 44 33
576......................................... 40 40
577......................................... 28 58
578......................................... 27 63
579......................................... 35 45
580......................................... 20 66
581......................................... 15 60
582......................................... 10 52
583......................................... 22 56
584......................................... 30 62
585......................................... 21 67
586......................................... 29 53
587......................................... 41 56
588......................................... 15 67
589......................................... 24 56
590......................................... 42 69
591......................................... 39 83
592......................................... 40 73
593......................................... 35 67
594......................................... 32 61
595......................................... 30 65
596......................................... 30 72
597......................................... 48 51
598......................................... 66 58
599......................................... 62 71
600......................................... 36 63
601......................................... 17 59
602......................................... 16 50
603......................................... 16 62
604......................................... 34 48
605......................................... 51 66
606......................................... 35 74
607......................................... 15 56
608......................................... 19 54
609......................................... 43 65
610......................................... 52 80
611......................................... 52 83
612......................................... 49 57
613......................................... 48 46
614......................................... 37 36
615......................................... 25 44
616......................................... 14 53
617......................................... 13 64
618......................................... 23 56
619......................................... 21 63
620......................................... 18 67
621......................................... 20 54
622......................................... 16 67
623......................................... 26 56
624......................................... 41 65
625......................................... 28 62
626......................................... 19 60
627......................................... 33 56
628......................................... 37 70
629......................................... 24 79
630......................................... 28 57
631......................................... 40 57
632......................................... 40 58
633......................................... 28 44
634......................................... 25 41
635......................................... 29 53
636......................................... 31 55
637......................................... 26 64
638......................................... 20 50
639......................................... 16 53
640......................................... 11 54
641......................................... 13 53
642......................................... 23 50
643......................................... 32 59
644......................................... 36 63
645......................................... 33 59
646......................................... 24 52
647......................................... 20 52
648......................................... 22 55
649......................................... 30 53
650......................................... 37 59
651......................................... 41 58
652......................................... 36 54
653......................................... 29 49
654......................................... 24 53
655......................................... 14 57
656......................................... 10 54
657......................................... 9 55
658......................................... 10 57
659......................................... 13 55
660......................................... 15 64
[[Page 68378]]
661......................................... 31 57
662......................................... 19 69
663......................................... 14 59
664......................................... 33 57
665......................................... 41 65
666......................................... 39 64
667......................................... 39 59
668......................................... 39 51
669......................................... 28 41
670......................................... 19 49
671......................................... 27 54
672......................................... 37 63
673......................................... 32 74
674......................................... 16 70
675......................................... 12 67
676......................................... 13 60
677......................................... 17 56
678......................................... 15 62
679......................................... 25 47
680......................................... 27 64
681......................................... 14 71
682......................................... 5 65
683......................................... 6 57
684......................................... 6 57
685......................................... 15 52
686......................................... 22 61
687......................................... 14 77
688......................................... 12 67
689......................................... 12 62
690......................................... 14 59
691......................................... 15 58
692......................................... 18 55
693......................................... 22 53
694......................................... 19 69
695......................................... 14 67
696......................................... 9 63
697......................................... 8 56
698......................................... 17 49
699......................................... 25 55
700......................................... 14 70
701......................................... 12 60
702......................................... 22 57
703......................................... 27 67
704......................................... 29 68
705......................................... 34 62
706......................................... 35 61
707......................................... 28 78
708......................................... 11 71
709......................................... 4 58
710......................................... 5 58
711......................................... 10 56
712......................................... 20 63
713......................................... 13 76
714......................................... 11 65
715......................................... 9 60
716......................................... 7 55
717......................................... 8 53
718......................................... 10 60
719......................................... 28 53
720......................................... 12 73
721......................................... 4 64
722......................................... 4 61
723......................................... 4 61
724......................................... 10 56
725......................................... 8 61
726......................................... 20 56
727......................................... 32 62
728......................................... 33 66
729......................................... 34 73
730......................................... 31 61
731......................................... 33 55
732......................................... 33 60
733......................................... 31 59
734......................................... 29 58
735......................................... 31 53
736......................................... 33 51
737......................................... 33 48
738......................................... 27 44
739......................................... 21 52
740......................................... 13 57
741......................................... 12 56
742......................................... 10 64
743......................................... 22 47
744......................................... 15 74
745......................................... 8 66
746......................................... 34 47
747......................................... 18 71
748......................................... 9 57
749......................................... 11 55
750......................................... 12 57
751......................................... 10 61
752......................................... 16 53
753......................................... 12 75
754......................................... 6 70
755......................................... 12 55
756......................................... 24 50
757......................................... 28 60
758......................................... 28 64
759......................................... 23 60
760......................................... 20 56
761......................................... 26 50
762......................................... 28 55
763......................................... 18 56
764......................................... 15 52
765......................................... 11 59
766......................................... 16 59
767......................................... 34 54
768......................................... 16 82
769......................................... 15 64
770......................................... 36 53
771......................................... 45 64
772......................................... 41 59
773......................................... 34 50
774......................................... 27 45
775......................................... 22 52
776......................................... 18 55
777......................................... 26 54
778......................................... 39 62
779......................................... 37 71
780......................................... 32 58
781......................................... 24 48
782......................................... 14 59
783......................................... 7 59
784......................................... 7 55
785......................................... 18 49
786......................................... 40 62
787......................................... 44 73
788......................................... 41 68
789......................................... 35 48
790......................................... 29 54
791......................................... 22 69
792......................................... 46 53
793......................................... 59 71
794......................................... 69 68
795......................................... 75 47
796......................................... 62 32
797......................................... 48 35
798......................................... 27 59
799......................................... 13 58
800......................................... 14 54
801......................................... 21 53
802......................................... 23 56
803......................................... 23 57
804......................................... 23 65
805......................................... 13 65
806......................................... 9 64
807......................................... 27 56
808......................................... 26 78
809......................................... 40 61
810......................................... 35 76
811......................................... 28 66
812......................................... 23 57
813......................................... 16 50
814......................................... 11 53
815......................................... 9 57
816......................................... 9 62
817......................................... 27 57
818......................................... 42 69
819......................................... 47 75
820......................................... 53 67
821......................................... 61 62
822......................................... 63 53
823......................................... 60 54
824......................................... 56 44
825......................................... 49 39
826......................................... 39 35
827......................................... 30 34
828......................................... 33 46
829......................................... 44 56
830......................................... 50 56
831......................................... 44 52
832......................................... 38 46
833......................................... 33 44
834......................................... 29 45
835......................................... 24 46
836......................................... 18 52
837......................................... 9 55
838......................................... 10 54
839......................................... 20 53
840......................................... 27 58
841......................................... 29 59
842......................................... 30 62
843......................................... 30 65
844......................................... 27 66
845......................................... 32 58
846......................................... 40 56
847......................................... 41 57
848......................................... 18 73
849......................................... 15 55
850......................................... 18 50
851......................................... 17 52
852......................................... 20 49
853......................................... 16 62
854......................................... 4 67
855......................................... 2 64
856......................................... 7 54
857......................................... 10 50
858......................................... 9 57
859......................................... 5 62
860......................................... 12 51
861......................................... 14 65
862......................................... 9 64
863......................................... 31 50
864......................................... 30 78
865......................................... 21 65
866......................................... 14 51
867......................................... 10 55
868......................................... 6 59
869......................................... 7 59
870......................................... 19 54
871......................................... 23 61
872......................................... 24 62
873......................................... 34 61
874......................................... 51 67
875......................................... 60 66
876......................................... 58 55
[[Page 68379]]
877......................................... 60 52
878......................................... 64 55
879......................................... 68 51
880......................................... 63 54
881......................................... 64 50
882......................................... 68 58
883......................................... 73 47
884......................................... 63 40
885......................................... 50 38
886......................................... 29 61
887......................................... 14 61
888......................................... 14 53
889......................................... 42 6
890......................................... 58 6
891......................................... 58 6
892......................................... 77 39
893......................................... 93 56
894......................................... 93 44
895......................................... 93 37
896......................................... 93 31
897......................................... 93 25
898......................................... 93 26
899......................................... 93 27
900......................................... 93 25
901......................................... 93 21
902......................................... 93 22
903......................................... 93 24
904......................................... 93 23
905......................................... 93 27
906......................................... 93 34
907......................................... 93 32
908......................................... 93 26
909......................................... 93 31
910......................................... 93 34
911......................................... 93 31
912......................................... 93 33
913......................................... 93 36
914......................................... 93 37
915......................................... 93 34
916......................................... 93 30
917......................................... 93 32
918......................................... 93 35
919......................................... 93 35
920......................................... 93 32
921......................................... 93 28
922......................................... 93 23
923......................................... 94 18
924......................................... 95 18
925......................................... 96 17
926......................................... 95 13
927......................................... 96 10
928......................................... 95 9
929......................................... 95 7
930......................................... 95 7
931......................................... 96 7
932......................................... 96 6
933......................................... 96 6
934......................................... 95 6
935......................................... 90 6
936......................................... 69 43
937......................................... 76 62
938......................................... 93 47
939......................................... 93 39
940......................................... 93 35
941......................................... 93 34
942......................................... 93 36
943......................................... 93 39
944......................................... 93 34
945......................................... 93 26
946......................................... 93 23
947......................................... 93 24
948......................................... 93 24
949......................................... 93 22
950......................................... 93 19
951......................................... 93 17
952......................................... 93 19
953......................................... 93 22
954......................................... 93 24
955......................................... 93 23
956......................................... 93 20
957......................................... 93 20
958......................................... 94 19
959......................................... 95 19
960......................................... 95 17
961......................................... 96 13
962......................................... 95 10
963......................................... 96 9
964......................................... 95 7
965......................................... 95 7
966......................................... 95 7
967......................................... 95 6
968......................................... 96 6
969......................................... 96 6
970......................................... 89 6
971......................................... 68 6
972......................................... 57 6
973......................................... 66 32
974......................................... 84 52
975......................................... 93 46
976......................................... 93 42
977......................................... 93 36
978......................................... 93 28
979......................................... 93 23
980......................................... 93 19
981......................................... 93 16
982......................................... 93 15
983......................................... 93 16
984......................................... 93 15
985......................................... 93 14
986......................................... 93 15
987......................................... 93 16
988......................................... 94 15
989......................................... 93 32
990......................................... 93 45
991......................................... 93 43
992......................................... 93 37
993......................................... 93 29
994......................................... 93 23
995......................................... 93 20
996......................................... 93 18
997......................................... 93 16
998......................................... 93 17
999......................................... 93 16
1000........................................ 93 15
1001........................................ 93 15
1002........................................ 93 15
1003........................................ 93 14
1004........................................ 93 15
1005........................................ 93 15
1006........................................ 93 14
1007........................................ 93 13
1008........................................ 93 14
1009........................................ 93 14
1010........................................ 93 15
1011........................................ 93 16
1012........................................ 93 17
1013........................................ 93 20
1014........................................ 93 22
1015........................................ 93 20
1016........................................ 93 19
1017........................................ 93 20
1018........................................ 93 19
1019........................................ 93 19
1020........................................ 93 20
1021........................................ 93 32
1022........................................ 93 37
1023........................................ 93 28
1024........................................ 93 26
1025........................................ 93 24
1026........................................ 93 22
1027........................................ 93 22
1028........................................ 93 21
1029........................................ 93 20
1030........................................ 93 20
1031........................................ 93 20
1032........................................ 93 20
1033........................................ 93 19
1034........................................ 93 18
1035........................................ 93 20
1036........................................ 93 20
1037........................................ 93 20
1038........................................ 93 20
1039........................................ 93 19
1040........................................ 93 18
1041........................................ 93 18
1042........................................ 93 17
1043........................................ 93 16
1044........................................ 93 16
1045........................................ 93 15
1046........................................ 93 16
1047........................................ 93 18
1048........................................ 93 37
1049........................................ 93 48
1050........................................ 93 38
1051........................................ 93 31
1052........................................ 93 26
1053........................................ 93 21
1054........................................ 93 18
1055........................................ 93 16
1056........................................ 93 17
1057........................................ 93 18
1058........................................ 93 19
1059........................................ 93 21
1060........................................ 93 20
1061........................................ 93 18
1062........................................ 93 17
1063........................................ 93 17
1064........................................ 93 18
1065........................................ 93 18
1066........................................ 93 18
1067........................................ 93 19
1068........................................ 93 18
1069........................................ 93 18
1070........................................ 93 20
1071........................................ 93 23
1072........................................ 93 25
1073........................................ 93 25
1074........................................ 93 24
1075........................................ 93 24
1076........................................ 93 22
1077........................................ 93 22
1078........................................ 93 22
1079........................................ 93 19
1080........................................ 93 16
1081........................................ 95 17
1082........................................ 95 37
1083........................................ 93 43
1084........................................ 93 32
1085........................................ 93 27
1086........................................ 93 26
1087........................................ 93 24
1088........................................ 93 22
1089........................................ 93 22
1090........................................ 93 22
1091........................................ 93 23
1092........................................ 93 22
[[Page 68380]]
1093........................................ 93 22
1094........................................ 93 23
1095........................................ 93 23
1096........................................ 93 23
1097........................................ 93 22
1098........................................ 93 23
1099........................................ 93 23
1100........................................ 93 23
1101........................................ 93 25
1102........................................ 93 27
1103........................................ 93 26
1104........................................ 93 25
1105........................................ 93 27
1106........................................ 93 27
1107........................................ 93 27
1108........................................ 93 24
1109........................................ 93 20
1110........................................ 93 18
1111........................................ 93 17
1112........................................ 93 17
1113........................................ 93 18
1114........................................ 93 18
1115........................................ 93 18
1116........................................ 93 19
1117........................................ 93 22
1118........................................ 93 22
1119........................................ 93 19
1120........................................ 93 17
1121........................................ 93 17
1122........................................ 93 18
1123........................................ 93 18
1124........................................ 93 19
1125........................................ 93 19
1126........................................ 93 20
1127........................................ 93 19
1128........................................ 93 20
1129........................................ 93 25
1130........................................ 93 30
1131........................................ 93 31
1132........................................ 93 26
1133........................................ 93 21
1134........................................ 93 18
1135........................................ 93 20
1136........................................ 93 25
1137........................................ 93 24
1138........................................ 93 21
1139........................................ 93 21
1140........................................ 93 22
1141........................................ 93 22
1142........................................ 93 28
1143........................................ 93 29
1144........................................ 93 23
1145........................................ 93 21
1146........................................ 93 18
1147........................................ 93 16
1148........................................ 93 16
1149........................................ 93 16
1150........................................ 93 17
1151........................................ 93 17
1152........................................ 93 17
1153........................................ 93 17
1154........................................ 93 23
1155........................................ 93 26
1156........................................ 93 22
1157........................................ 93 18
1158........................................ 93 16
1159........................................ 93 16
1160........................................ 93 17
1161........................................ 93 19
1162........................................ 93 18
1163........................................ 93 16
1164........................................ 93 19
1165........................................ 93 22
1166........................................ 93 25
1167........................................ 93 29
1168........................................ 93 27
1169........................................ 93 22
1170........................................ 93 18
1171........................................ 93 16
1172........................................ 93 19
1173........................................ 93 19
1174........................................ 93 17
1175........................................ 93 17
1176........................................ 93 17
1177........................................ 93 16
1178........................................ 93 16
1179........................................ 93 15
1180........................................ 93 16
1181........................................ 93 15
1182........................................ 93 17
1183........................................ 93 21
1184........................................ 93 30
1185........................................ 93 53
1186........................................ 93 54
1187........................................ 93 38
1188........................................ 93 30
1189........................................ 93 24
1190........................................ 93 20
1191........................................ 95 20
1192........................................ 96 18
1193........................................ 96 15
1194........................................ 96 11
1195........................................ 95 9
1196........................................ 95 8
1197........................................ 96 7
1198........................................ 94 33
1199........................................ 93 46
1200........................................ 93 37
1201........................................ 16 8
1202........................................ 0 0
1203........................................ 0 0
1204........................................ 0 0
1205........................................ 0 0
1206........................................ 0 0
1207........................................ 0 0
1208........................................ 0 0
1209........................................ 0 0
------------------------------------------------------------------------
£PART 1051--CONTROL OF EMISSIONS FROM RECREATIONAL
ENGINES AND VEHICLES
Subpart A--Determining How To Follow This Part
Sec.
1051.1 Does this part apply to me?
1051.5 Which engines are excluded or exempted from this part's
requirements?
1051.10 What main steps must I take to comply with this part?
1051.15 Do any other regulation parts affect me?
1051.20 May I certify a recreational engine instead of the vehicle?
1051.25 What requirements apply when installing certified engines in
recreational vehicles?
Subpart B--Emission Standards and Related Requirements
1051.101 What emission standards and other requirements must my
vehicles meet?
1051.103 What are the exhaust emission standards for snowmobiles?
1051.105 What are the exhaust emission standards for off-highway
motorcycles?
1051.107 What are the exhaust emission standards for all-terrain
vehicles (ATVs) and offroad utility vehicles?
1051.110 What evaporative emission standards must my vehicles meet?
1051.115 What other requirements must my vehicles meet?
1051.120 What warranty requirements apply to me?
1051.125 What maintenance instructions must I give to buyers?
1051.130 What installation instructions must I give to vehicle
manufacturers?
1051.135 How must I label and identify the vehicles I produce?
1051.145 What provisions apply only for a limited time?
Subpart C--Certifying Engine Families
1051.201 What are the general requirements for submitting a
certification application?
1051.205 What must I include in my application?
1051.210 May I get preliminary approval before I complete my
application?
1051.215 What happens after I complete my application?
1051.220 How do I amend the maintenance instructions in my
application?
1051.225 How do I amend my application to include new or modified
vehicles or to change an FEL?
1051.230 How do I select engine families?
1051.235 What emission testing must I perform for my application for
a certificate of conformity?
1051.240 How do I demonstrate that my engine family complies with
exhaust emission standards?
1051.245 How do I demonstrate that my engine family complies with
evaporative emission standards?
1051.250 What records must I keep and make available to EPA?
1051.255 When may EPA deny, revoke, or void my certificate of
conformity?
Subpart D--Testing Production-Line Engines
1051.301 When must I test my production-line vehicles or engines?
1051.305 How must I prepare and test my production-line vehicles or
engines?
1051.310 How must I select vehicles or engines for production-line
testing?
1051.315 How do I know when my engine family fails the production-
line testing requirements?
1051.320 What happens if one of my production-line vehicles or
engines fails to meet emission standards?
1051.325 What happens if an engine family fails the production-line
requirements?
1051.330 May I sell vehicles from an engine family with a suspended
certificate of conformity?
1051.335 How do I ask EPA to reinstate my suspended certificate?
1051.340 When may EPA revoke my certificate under this subpart and
how may I sell these vehicles again?
[[Page 68381]]
1051.345 What production-line testing records must I send to EPA?
1051.350 What records must I keep?
Subpart E--Testing In-Use Engines [Reserved]
Subpart F--Test Procedures
1051.501 What procedures must I use to test my vehicles or engines?
1051.505 What special provisions apply for testing snowmobiles?
1051.510 What special provisions apply for testing ATV engines?
[Reserved]
1051.515 How do I test my fuel tank for permeation emissions?
1051.520 How do I perform exhaust durability testing?
Subpart G--Compliance Provisions
1051.601 What compliance provisions apply to vehicles and engines
subject to this part?
1051.605 What are the provisions for exempting vehicles from the
requirements of this part if they use engines you have certified
under the motor-vehicle program or the Large Spark-ignition program?
1051.610 What are the provisions for producing recreational vehicles
with engines already certified under the motor-vehicle program or
the Large SI program?
1051.615 What are the special provisions for certifying small
recreational engines?
1051.620 When may a manufacturer obtain an exemption for competition
recreational vehicles?
1051.625 What special provisions apply to unique snowmobile designs
for small-volume manufacturers?
1051.630 What special provisions apply to unique snowmobile designs
for all manufacturers?
1051.635 What provisions apply to new manufacturers that are small
businesses?
Subpart H--Averaging, Banking, and Trading for Certification
1051.701 General provisions.
1051.705 How do I average emission levels?
1051.710 How do I generate and bank emission credits?
1051.715 How do I trade emission credits?
1051.720 How do I calculate my average emission level or emission
credits?
1051.725 What information must I keep?
1051.730 What information must I report?
1051.735 Are there special averaging provisions for snowmobiles?
Subpart I--Definitions and Other Reference Information
1051.801 What definitions apply to this part?
1051.805 What symbols, acronyms, and abbreviations does this part
use?
1051.810 What materials does this part reference?
1051.815 How should I request EPA to keep my information
confidential?
1051.820 How do I request a hearing?
Authority: 42 U.S.C. 7401-7671(q).
Subpart A--Determining How to Follow This Part
Sec. 1051.1 Does this part apply to me?
(a) This part applies to you if you manufacture or import any of
the following recreational vehicles or engines used in them, unless we
exclude them under Sec. 1051.5:
(1) Snowmobiles.
(2) Off-highway motorcycles.
(3) All-terrain vehicles (ATVs).
(4) Offroad utility vehicles with engines with displacement less
than or equal to 1000 cc, maximum brake power less than or equal to 30
kW, and maximum vehicle speed of 25 miles per hour or higher. Offroad
utility vehicles that are subject to this part are subject to the same
requirements as ATVs. This means that any requirement that applies to
ATVs also applies to these offroad utility vehicles, without regard to
whether the regulatory language mentions offroad utility vehicles.
(b) [Reserved]
(c) As noted in subpart G of this part, 40 CFR part 1068 applies to
everyone, including anyone who manufactures, installs, owns, operates,
or rebuilds any of the vehicles or engines this part covers.
(d) You need not follow this part for vehicles you produce before
the 2006 model year, unless you certify voluntarily. See Sec. Sec.
1051.103 through 1051.110, Sec. 1051.145, and the definition of
``model year'' in Sec. 1051.801 for more information about the timing
of the requirements.
(e) The requirements of this part begin to apply when a vehicle is
new. See the definition of ``new'' in Sec. 1051.801 for more
information. In some cases, vehicles or engines that have been
previously used may be considered ``new'' for the purposes of this
part.
(f) See Sec. Sec. 1051.801 and 1051.805 for definitions and
acronyms that apply to this part. The definition section contains
significant regulatory provisions and it is very important that you
read them.
Sec. 1051.5 Which engines are excluded or exempted from this part's
requirements?
(a) You may exclude vehicles with compression-ignition engines. See
40 CFR part 89 for regulations that cover these engines.
(b) See subpart G of this part and 40 CFR part 1068, subpart C, for
exemptions of specific engines.
(c) We may require you to label an engine or vehicle (or both) if
this section excludes it and other requirements in this chapter do not
apply.
(d) Send the Designated Officer a written request with supporting
documentation if you want us to determine whether this part covers or
excludes certain vehicles. Excluding engines from this part's
requirements does not affect other requirements that may apply to them.
Sec. 1051.10 What main steps must I take to comply with this part?
(a) You must get a certificate of conformity from us for each
engine family before you do any of the following things with a new
vehicle or new engine covered by this part: sell, offer for sale,
introduce into commerce, distribute or deliver for introduction into
commerce, or import it into the United States. ``New'' vehicles or
engines may include some already placed in service (see the definition
of ``new'' in Sec. 1051.801). You must get a new certificate of
conformity for each new model year.
(b) To get a certificate of conformity and comply with its terms,
you must do five things:
(1) Meet the emission standards and other requirements in subpart B
of this part.
(2) Perform preproduction emission tests.
(3) Apply for certification (see subpart C of this part).
(4) Do routine emission testing on production vehicles or engines
as required by subpart D of this part.
(5) Follow our instructions throughout this part.
(c) Subpart F of this part describes how to test your engines or
vehicles (including references to other parts) and when you may test
the engine alone instead of the entire vehicle.
(d) Subpart G of this part and 40 CFR part 1068 describe
requirements and prohibitions that apply to manufacturers, owners,
operators, rebuilders, and all others. They also describe exemptions
available for special circumstances.
Sec. 1051.15 Do any other regulation parts affect me?
(a) Parts 86 and 1065 of this chapter describe procedures and
equipment specifications for testing vehicles and engines. Subpart F of
this part describes how to apply part 86 or 1065 of this chapter to
show you meet the emission standards in this part.
(b) Part 1068 of this chapter describes general provisions,
including these seven areas:
(1) Prohibited actions and penalties for manufacturers and others.
(2) Rebuilding and other aftermarket changes.
(3) Exemptions and exclusions for certain vehicles and engines.
[[Page 68382]]
(4) Importing vehicles and engines.
(5) Selective enforcement audits of your production.
(6) Defect reporting and recall.
(7) Procedures for hearings.
(c) Other parts of this chapter affect you if referenced in this
part.
Sec. 1051.20 May I certify a recreational engine instead of the
vehicle?
(a) You may certify engines sold separately from vehicles in either
of two cases:
(1) If you manufacture recreational engines but not recreational
vehicles, you may ask to certify the engine alone. In your request,
explain why you cannot certify the entire vehicle.
(2) If you manufacture complete recreational vehicles containing
engines you also sell separately, you may ask to certify all these
engines in a single engine family or in separate engine families.
(b) If you certify an engine under this section, you must use the
test procedures in subpart F of this part. If the test procedures
require vehicle testing, use good engineering judgment to install the
engine in an appropriate vehicle for measuring emissions.
(c) If we allow you to certify recreational engines, the vehicles
must meet the applicable emission standards (including evaporative
emission standards) with the engines installed in the appropriate
vehicles. You must prepare installation instructions as described in
Sec. 1051.130 and use good engineering judgment so that the engines
will meet emission standards after proper installation in the vehicle.
(d) Identify and label engines you produce under this section
consistent with the requirements of Sec. 1051.135. On the emission
control information label, identify the manufacturing date of the
engine rather than the vehicle.
(e) You may not use the provisions of this section to circumvent or
reduce the stringency of this part's standards or other requirements.
(f) If you certify under paragraph (a)(1) of this section, you may
ask us to allow you to perform production-line testing on the engine.
If you certify under paragraph (a)(2) of this section, use good
engineering judgment to ensure that these engines are produced in the
same manner as the engines you produce for your vehicles, so that your
production-line testing results under subpart D of this part would
apply to them.
Sec. 1051.25 What requirements apply when installing certified
engines in recreational vehicles?
(a) If you manufacture recreational vehicles with engines certified
under Sec. 1051.20, you need not also certify the vehicle under this
part. The vehicle must nevertheless meet emission standards with the
engine installed.
(b) You must follow the engine manufacturer's emission-related
installation instructions, as described in Sec. 1051.135 and 40 CFR
1068.105. For example, you must use a fuel system that meets the
permeation requirements of this part, consistent with the engine
manufacturer's instructions.
(c) If you install the engine in a way that makes the engine's
emission control information label hard to read during normal engine
maintenance, you must place a duplicate label on the vehicle, as
described in 40 CFR 1068.105.
Subpart B--Emission Standards and Related Requirements
Sec. 1051.101 What emission standards and other requirements must my
vehicles meet?
(a) You must show that your vehicles meet the following:
(1) The applicable exhaust emission standards in Sec. 1051.103,
Sec. 1051.105, or Sec. 1051.107.
(i) For snowmobiles, see Sec. 1051.103.
(ii) For off-highway motorcycles, see Sec. 1051.105.
(iii) For all-terrain vehicles and offroad utility vehicles subject
to this part, see Sec. 1051.107.
(2) The evaporative emission standards in Sec. 1051.110.
(3) All the requirements in Sec. 1051.115.
(b) The certification regulations in subpart C of this part
describe how you make this showing.
(c) These standards and requirements apply to all testing,
including production-line and in-use testing, as described in subparts
D and E of this part.
(d) Other sections in this subpart describe other requirements for
manufacturers such as labeling or warranty requirements.
(e) It is important that you read Sec. 1051.145 to determine if
there are other interim requirements or interim compliance options that
apply for a limited time.
(f) As is described in Sec. 1051.1(a)(4), offroad utility vehicles
that are subject to this part are subject to the same requirements as
ATVs.
Sec. 1051.103 What are the exhaust emission standards for
snowmobiles?
(a) Apply the exhaust emission standards in this section by model
year. Measure emissions with the snowmobile test procedures in subpart
F of this part.
(1) Follow Table 1 of this section for exhaust emission standards.
You may use the averaging, banking, and trading provisions of subpart H
of this part to show compliance with these standards (an engine family
meets emission standards even if its family emission limit is higher
than the standard, as long as you show that the whole averaging set of
applicable engine families meet the applicable emission standards using
emission credits, and the vehicles within the family meet the family
emission limit). Table 1 also shows the maximum value you may specify
for a family emission limit, as follows:
Table 1 of Sec. 1051.103.--Exhaust Emission Standards for Snowmobiles (g/kW-hr)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Emission standards Maximum allowable family emission limits
Phase Model year Phase-in --------------------------------------------------------------------------------
(percent) HC HC+NOX CO HC HC+NOX CO
--------------------------------------------------------------------------------------------------------------------------------------------------------
Phase 1............................ 2006................. 50 100 ........... 275 ........... ........... ..............
------------------------------------
Phase 1............................ 2007-2009............ 100 100 ........... 275 ........... ........... ..............
------------------------------------
Phase 2............................ 2010 and 2011........ 100 75 ........... 275 ........... ........... ..............
------------------------------------
Phase 3............................ 2012 and later....... 100 75 (\1\) (\1\) 150 165 400
--------------------------------------------------------------------------------------------------------------------------------------------------------
\1\ See Sec. 1051.103(a)(2).
[[Page 68383]]
(2) For Phase 3, the HC+NOX and CO standards are defined
by a functional relationship. Choose your corporate average
HC+NOX and CO standards for each model year according to the
following criteria:
(i) Prior to production, select the HC+NOX standard and
CO standard (specified as g/kW-hr) so that the combined percent
reduction from baseline emission levels is greater than or equal to 100
percent; that is, that the standards comply with the following
equation:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.007
(ii) Your corporate average HC+NOX standard may not be
higher than 90 g/kW-hr.
(iii) Your corporate average CO standard may not be higher than 275
g/kW-hr.
(iv) You may use the averaging and banking provisions of subpart H
of this part to show compliance with these HC+NOX and CO
standards in this paragraph (a)(2). You may modify your selection of
the HC+NOX and CO standards at the end of the model year
under paragraph (a)(2)(i) of this section. You must comply with these
final corporate average emission standards.
(b) Apply the exhaust emission standards in this section for
snowmobiles using each type of fuel specified in 40 CFR part 1065,
subpart C, for which they are designed to operate. You must meet the
numerical emission standards for hydrocarbons in this section based on
the following types of hydrocarbon emissions for snowmobiles powered by
the following fuels:
(1) Gasoline- and LPG-fueled snowmobiles: THC emissions.
(2) Natural gas-fueled snowmobiles: NMHC emissions.
(3) Alcohol-fueled snowmobiles: THCE emissions.
(c) Your snowmobiles must meet emission standards over their full
useful life (Sec. 1051.240 describes how to use deterioration factors
to show this). The minimum useful life is 8,000 kilometers, 400 hours
of engine operation, or five calendar years, whichever comes first. You
must specify a longer useful life in terms of kilometers and hours for
the engine family if the average service life of your vehicles is
longer than the minimum value, as follows:
(1) Except as allowed by paragraph (c)(2) of this section, your
useful life (in kilometers and hours) may not be less than either of
the following:
(i) Your projected operating life from advertisements or other
marketing materials for any vehicles in the engine family.
(ii) Your basic mechanical warranty for any engines in the engine
family.
(2) Your useful life may be based on the average service life of
vehicles in the engine family if you show that the average service life
is less than the useful life required by paragraph (c)(1) of this
section, but more than the minimum useful life (8,000 kilometers or 400
hours of engine operation). In determining the actual average service
life of vehicles in an engine family, we will consider all available
information and analyses. Survey data is allowed but not required to
make this showing.
Sec. 1051.105 What are the exhaust emission standards for off-highway
motorcycles?
(a) Apply the exhaust emission standards in this section by model
year. Measure emissions with the off-highway motorcycle test procedures
in subpart F of this part.
(1) Follow Table 1 of this section for exhaust emission standards.
You may use the averaging, banking, and trading provisions of subpart H
of this part to show compliance with the HC+NOX and/or CO
standards (an engine family meets emission standards even if its family
emission limit is higher than the standard, as long as you show that
the whole averaging set of applicable engine families meet the
applicable emission standards using emission credits, and the vehicles
within the family meet the family emission limit). The phase-in values
specify the percentage of your U.S.-directed production that must
comply with the emission standards for those model years. Calculate
this compliance percentage based on a simple count of production units
within the engine family. Table 1 follows:
Table 1 of Sec. 1051.105.--Exhaust Emission Standards for Off-Highway Motorcycles (g/km)
----------------------------------------------------------------------------------------------------------------
Emission standards Maximum allowable family
Phase-in -------------------------- emission limits
Phase Model year (percent) -------------------------
HC+NOX CO HC+NOX CO
----------------------------------------------------------------------------------------------------------------
Phase 1...................... 2006............ 50 2.0 25 20.0 50
-------------------
2007 and later.. 100 2.0 25 20.0 50
----------------------------------------------------------------------------------------------------------------
(2) For model years 2007 and later you may choose to certify all of
your off-highway motorcycles to an HC+NOX standard of 4.0 g/
km and a CO standard of 35 g/km, instead of the standards listed in
paragraph (a)(1) of this section. To certify to the standards in this
paragraph (a)(2), you must comply with the following provisions:
(i) You may not request an exemption for any off-highway
motorcycles under Sec. 1051.620
(ii) At least ten percent of your off-highway motorcycles for the
model year must have four of the following features:
(A) The absence of a headlight or other lights.
(B) The absence of a spark arrestor.
(C) The absence of manufacturer warranty.
(D) Suspension travel greater than 10 inches.
(E) Engine displacement greater than 50 cc.
(F) The absence of a functional seat.
(iii) You may use the averaging and banking provisions of subpart H
of this part to show compliance with this HC+NOX standard,
but not this CO standard. If you use the averaging or banking
provisions to show compliance, your FEL for HC+NOX may not
exceed 8.0 g/km for any engine family. You may not use the trading
provisions of subpart H of this part.
(3) You may certify off-highway motorcycles with engines that have
total
[[Page 68384]]
displacement of 70 cc or less to the exhaust emission exhaust standards
in Sec. 1051.615 instead of certifying them to the exhaust emission
standards of this section.
(b) Apply the exhaust emission standards in this section for off-
highway motorcycles using each type of fuel specified in 40 CFR part
1068, subpart C, for which they are designed to operate. You must meet
the numerical emission standards for hydrocarbons in this section based
on the following types of hydrocarbon emissions for off-highway
motorcycles powered by the following fuels:
(1) Gasoline- and LPG-fueled off-highway motorcycles: THC
emissions.
(2) Natural gas-fueled off-highway motorcycles: NMHC emissions.
(3) Alcohol-fueled off-highway motorcycles: THCE emissions.
(c) Your off-highway motorcycles must meet emission standards over
their full useful life (Sec. 1051.240 describes how to use
deterioration factors to show this). The minimum useful life is 10,000
kilometers or five years, whichever comes first. You must specify a
longer useful life for the engine family in terms of kilometers if the
average service life of your vehicles is longer than the minimum value,
as follows:
(1) Except as allowed by paragraph (c)(2) of this section, your
useful life (in kilometers) may not be less than either of the
following:
(i) Your projected operating life from advertisements or other
marketing materials for any vehicles in the engine family.
(ii) Your basic mechanical warranty for any engines in the engine
family.
(2) Your useful life may be based on the average service life of
vehicles in the engine family if you show that the average service life
is less than the useful life required by paragraph (c)(1) of this
section, but more than the minimum useful life (10,000 kilometers). In
determining the actual average service life of vehicles in an engine
family, we will consider all available information and analyses. Survey
data is allowed but not required to make this showing.
Sec. 1051.107 What are the exhaust emission standards for all-terrain
vehicles (ATVs) and offroad utility vehicles?
This section specifies the exhaust emission standards that apply to
ATVs. As is described in Sec. 1051.1(a)(4), offroad utility vehicles
that are subject to this part are subject to these same standards.
(a) Apply the exhaust emission standards in this section by model
year. Measure emissions with the ATV test procedures in subpart F of
this part.
(1) Follow Table 1 of this section for exhaust emission standards.
You may use the averaging, banking, and trading provisions of subpart H
of this part to show compliance with these HC+NOX standards
(an engine family meets emission standards even if its family emission
limit is higher than the standard, as long as you show that the whole
averaging set of applicable engine families meet the applicable
emission standards using emission credits, and the vehicles within the
family meet the family emission limit). Table 1 also shows the maximum
value you may specify for a family emission limit. The phase-in values
in the table specify the percentage of your total U.S.-directed
production that must comply with the emission standards for those model
years. Calculate this compliance percentage based on a simple count of
production units within the engine family. This applies to your total
production of ATVs and offroad utility vehicles that are subject to the
standards of this part; including both ATVs and offroad utility
vehicles subject to the standards of this section and ATVs and offroad
utility vehicles certified to the standards of other sections in this
part 1051 (such as Sec. 1051.615, but not including vehicles certified
under other parts in this chapter (such as 40 CFR part 90). Table 1
follows:
Table 1 of Sec. 1051.107.--Exhaust Emission Standards for ATVs (g/km)
----------------------------------------------------------------------------------------------------------------
Emission standards Maximum allowable family
Phase-in -------------------------- emission limits
Phase Model year (percent) -------------------------
HC+NOX CO HC+NOX CO
----------------------------------------------------------------------------------------------------------------
Phase 1...................... 2006............ 50 1.5 35 20.0 50
2007 and later.. 100 1.5 35 20.0 50
----------------------------------------------------------------------------------------------------------------
(2) You may certify ATVs with engines that have total displacement
of less than 100 cc to the exhaust emission exhaust standards in Sec.
1051.615 instead of certifying them to the exhaust emission standards
of this section.
(b) Apply the exhaust emission standards in this section for ATVs
using each type of fuel specified in 40 CFR 1065, subpart C for which
they are designed to operate. You must meet the numerical emission
standards for hydrocarbons in this section based on the following types
of hydrocarbon emissions for ATVs powered by the following fuels:
(1) Gasoline- and LPG-fueled ATVs: THC emissions.
(2) Natural gas-fueled ATVs: NMHC emissions.
(3) Alcohol-fueled ATVs: THCE emissions.
(c) Your ATVs must meet emission standards over their full useful
life (Sec. 1051.240 describes how to use deterioration factors to show
this). The minimum useful life is 10,000 kilometers, 1000 hours of
engine operation, or five years, whichever comes first. You must
specify a longer useful life for the engine family in terms of
kilometers and hours if the average service life of your vehicles is
longer than the minimum value, as follows:
(1) Except as allowed by paragraph (c)(2) of this section, your
useful life (in kilometers) may not be less than either of the
following:
(i) Your projected operating life from advertisements or other
marketing materials for any vehicles in the engine family.
(ii) Your basic mechanical warranty for any engines in the engine
family.
(2) Your useful life may be based on the average service life of
vehicles in the engine family if you show that the average service life
is less than the useful life required by paragraph (c)(1) of this
section, but more than the minimum useful life (10,000 kilometers or
1,000 hours of engine operation). In determining the actual average
service life of vehicles in an engine family, we will consider all
available information and analyses. Survey data is allowed but not
required to make this showing.
Sec. 1051.110 What evaporative emission standards must my vehicles
meet?
All of your new vehicles must meet the emission standards of this
section over their full useful life, as specified in this section. Note
that Sec. 1051.245 allows you to use design-based certification
instead of generating new emission data.
[[Page 68385]]
(a) Beginning with the 2008 model year, permeation emissions from
your vehicle's fuel tank(s) may not exceed 1.5 grams per square-meter
per day when measured with the test procedures for tank permeation in
subpart F of this part. You may use the averaging, banking, and trading
provisions of subpart H of this part to show compliance.
(b) Beginning with the 2008 model year, permeation emissions from
your vehicle's fuel lines may not exceed 15 grams per square-meter per
day when measured with the test procedures for fuel-line permeation in
subpart F of this part. Use the inside diameter of the hose to
determine the surface area of the hose.
Sec. 1051.115 What other requirements must my vehicles meet?
Your vehicles must meet the following requirements:
(a) Closed crankcase. Design and produce your vehicles so they
release no crankcase emissions into the atmosphere throughout their
useful life.
(b) Emission sampling capability. Produce all your vehicles to
allow sampling of exhaust emissions in the field without damaging the
vehicle. Show in your application for certification how this can be
done in a way that prevents diluting the exhaust sample with ambient
air. To do this, you might simply allow for extending the exhaust pipe
by 20 cm; you might also install sample ports in the exhaust
(downstream of any aftertreatment devices).
(c) Adjustable parameters. If your vehicles have adjustable
parameters, they must meet all the requirements of this part for any
adjustment in the physically adjustable range. Note that parameters
that control the air-fuel ratio may be treated separately under
paragraph (d) of this section.
(1) We do not consider an operating parameter adjustable if you
permanently seal it or if ordinary tools cannot readily access it.
(2) We may require you to adjust the engine to any specification
within the adjustable range during certification testing, production-
line testing, selective enforcement auditing, or in-use testing.
(d) Other adjustments. This provision applies if an experienced
mechanic can change your engine's air-fuel ratio in less than one hour
with a few parts whose total cost is under $50 (in 2001 dollars).
Examples include carburetor jets and needles. In the case of carburetor
jets and needles, your vehicle must meet all the requirements of this
part for any air-fuel ratio within the adjustable range described in
paragraph (d)(1) of this section.
(1) In your application for certification, specify the adjustable
range of air-fuel ratios you expect to occur in use. You may specify it
in terms of engine parts (such as the carburetor jet size and needle
configuration as a function of atmospheric conditions).
(2) This adjustable range (specified in paragraph (d)(1) of this
section) must include all air-fuel ratios between the lean limit and
the rich limit, unless you can show that some air-fuel ratios will not
occur in use.
(i) The lean limit is the air-fuel ratio that produces the highest
engine power output (averaged over the test cycle).
(ii) The rich limit is the richest of the following air-fuel
ratios:
(A) The air-fuel ratio that would result from operating the vehicle
as you produce it at the specified test conditions. This paragraph
(d)(2)(ii)(A) does not apply if you produce the vehicle with an
unjetted carburetor so that the vehicle must be jetted by the dealer or
operator.
(B) The air-fuel ratio of the engine when you do durability
testing.
(C) The richest air-fuel ratio that you recommend to your customers
for the applicable ambient conditions.
(3) If the air-fuel ratio of your vehicle is adjusted primarily by
changing the carburetor jet size and/or needle configuration, you may
submit your recommended jetting chart instead of the range of air-fuel
ratios required by paragraph (d)(1) of this section if the following
criteria are met:
(i) Good engineering judgment indicates that vehicle operators
would not have an incentive to operate the vehicle with richer air-fuel
ratios than recommended.
(ii) The chart is based on use of a fuel that is equivalent to the
specified test fuel(s). As an alternative you may submit a chart based
on a representative in-use fuel if you also provide instructions for
converting the chart to be applicable to the test fuel(s).
(iii) The chart is specified in units that are adequate to make it
practical for an operator to keep the vehicle properly jetted during
typical use. For example, charts that specify jet sizes based on
increments of temperature smaller than 20[deg]F (11.1[deg]C) or
increments of altitude less than 2000 feet would not meet this
criteria. Temperature ranges must overlap by at least 5[deg]F
(2.8[deg]C).
(iv) You follow the jetting chart for durability testing.
(v) You do not produce your vehicles with jetting richer than the
jetting chart recommendation for the intended vehicle use.
(4) We may require you to adjust the engine to any specification
within the adjustable range during certification testing, production-
line testing, selective enforcement auditing, or in-use testing. If we
allow you to submit your recommended jetting chart instead of the range
of air-fuel ratios required by paragraph (d)(1) of this section, adjust
the engine to the richest specification within the jetting chart for
the test conditions, unless we specify a leaner setting. We may not
specify a setting leaner than that described in paragraph (d)(2)(i) of
this section.
(e) Prohibited controls. You may not design your engines with
emission-control devices, systems, or elements of design that cause or
contribute to an unreasonable risk to public health, welfare, or safety
while operating. For example, this would apply if the engine emits a
noxious or toxic substance it would otherwise not emit that contributes
to such an unreasonable risk.
(f) Defeat devices. You may not equip your vehicles with a defeat
device. A defeat device is an auxiliary emission-control device or
other control feature that reduces the effectiveness of emission
controls under conditions you may reasonably expect the vehicle to
encounter during normal operation and use. This does not apply to
auxiliary emission-control devices you identify in your certification
application if any of the following is true:
(1) The conditions of concern were substantially included in your
prescribed duty cycles.
(2) You show your design is necessary to prevent catastrophic
vehicle damage or accidents.
(3) The reduced effectiveness applies only to starting the engine.
(g) Noise standards. There are no noise standards specified in this
part 1051. See 40 CFR Chapter I, Subchapter G, to determine if your
vehicle must meet noise emission standards under another part our
regulations.
Sec. 1051.120 What warranty requirements apply to me?
(a) General requirements. You must warrant to the ultimate buyer
that the new engine meets two conditions:
(1) It is designed, built, and equipped to conform at the time of
sale with the requirements of this part.
(2) It is free from defects in materials and workmanship that may
keep it from meeting these requirements.
(b) Warranty period. Your emission-related warranty must be valid
for at least 50 percent of the vehicle's
[[Page 68386]]
minimum useful life in kilometers or at least 30 months, whichever
comes first. You may offer an emission-related warranty more generous
than we require. This warranty may not be shorter than any published or
negotiated warranty you offer for the engine or any of its components.
If a vehicle has no odometer, base warranty periods in this paragraph
(b) only on the vehicle's age (in years).
(c) Components covered. The emission-related warranty must cover
components whose failure would increase an engine's emissions,
including electronic controls, fuel injection (for liquid or gaseous
fuels), exhaust-gas recirculation, aftertreatment, or any other system
you develop to control emissions. We generally consider replacing or
repairing other components to be the owner's responsibility.
(d) Scheduled maintenance. You may schedule emission-related
maintenance for a component named in paragraph (c) of this section,
subject to the restrictions of Sec. 1051.125. You are not required to
cover this scheduled maintenance under your warranty if the component
meets either of the following criteria:
(1) The component was in general use on similar engines, and was
subject to scheduled maintenance, before January 1, 2000.
(2) Failure of the component would clearly degrade the engine's
performance enough that the operator would need to repair or replace
it.
(e) Limited applicability. You may deny warranty claims under this
section if the operator caused the problem, as described in 1068.115 of
this chapter. You may ask us to allow you to exclude from your
emission-related warranty certified vehicles that have been used
significantly for competition, especially certified motorcycles that
meet at least four of the criteria in Sec. 1051.620(b)(1).
(f) Aftermarket parts. As noted in Sec. 1068.101 of this chapter,
it is a violation of the Act to manufacture a vehicle part if one of
its main effects is to reduce the effectiveness of the vehicle's
emission controls. If you make an aftermarket part, you may--but do not
have to--certify that using the part will still allow engines to meet
emission standards, as described in Sec. 85.2114 of this chapter.
Sec. 1051.125 What maintenance instructions must I give to buyers?
Give the ultimate buyer of each new vehicle written instructions
for properly maintaining and using the vehicle, including the emission-
control system. The maintenance instructions also apply to service
accumulation on your test vehicles or engines, as described in 40 CFR
part 1065, subpart E.
(a) Critical emission-related maintenance. Critical emission-
related maintenance includes any adjustment, cleaning, repair, or
replacement of air-induction, fuel-system, or ignition components,
aftertreatment devices, pulse-air valves, exhaust gas recirculation
systems, crankcase ventilation valves, sensors, or electronic control
units. This may also include any other component whose only purpose is
to reduce emissions or whose failure will increase emissions without
significantly degrading engine performance. You may schedule critical
emission-related maintenance on these components if you meet the
following conditions:
(1) You may ask us to approve critical emission-related maintenance
only if it meets two criteria:
(i) Operators are reasonably likely to do the maintenance you call
for.
(ii) Vehicles need the maintenance to meet emission standards.
(2) We will accept scheduled maintenance as reasonably likely to
occur in use if you satisfy any of four conditions:
(i) You present data showing that, if a lack of maintenance
increases emissions, it also unacceptably degrades the vehicle's
performance.
(ii) You present survey data showing that 80 percent of vehicles in
the field get the maintenance you specify at the recommended intervals.
(iii) You provide the maintenance free of charge and clearly say so
in maintenance instructions for the customer.
(iv) You otherwise show us that the maintenance is reasonably
likely to be done at the recommended intervals.
(3) You may not schedule critical emission-related maintenance
within the minimum useful life period for aftertreatment devices,
pulse-air valves, fuel injectors, oxygen sensors, electronic control
units, superchargers, or turbochargers.
(b) Recommended additional maintenance. You may recommend, but not
require, any additional amount of maintenance on the components listed
in paragraph (a) of this section. However, you must make it clear that
these maintenance steps are not necessary to keep the emission-related
warranty valid. If operators do the maintenance specified in paragraph
(a) of this section, but not the recommended additional maintenance,
this does not allow you to disqualify them from in-use testing or deny
a warranty claim.
(c) Special maintenance. You may specify more frequent maintenance
to address problems related to special situations such as substandard
fuel or atypical engine operation. You may not perform this special
maintenance during service accumulation or durability testing.
(d) Noncritical emission-related maintenance. For engine parts not
listed in paragraph (a) of this section, you may schedule any amount of
emission-related inspection or maintenance. But you must state clearly
that these steps are not necessary to keep the emission-related
warranty valid. Also, do not take these inspection or maintenance steps
during service accumulation on your test vehicles or engines.
(e) Maintenance that is not emission-related. For maintenance
unrelated to emission controls, you may schedule any amount of
inspection or maintenance. You may also take these inspection or
maintenance steps during service accumulation on your test vehicles or
engines. This might include adding engine oil or adjusting chain
tension, clutch position, or tire pressure.
(f) Source of parts and repairs. Print clearly on the first page of
your written maintenance instructions that any repair shop or person
may maintain, replace, or repair emission-control devices and systems.
Your instructions may not require any component or service identified
by brand, trade, or corporate name. Also, do not directly or indirectly
condition your warranty on a requirement that the vehicle be serviced
by your franchised dealers or any other service establishments with
which you have a commercial relationship. You may disregard the
requirements in this paragraph (f) if you do one of two things:
(1) Provide a component or service without charge under the
purchase agreement.
(2) Get us to waive this prohibition in the public's interest by
convincing us the vehicle will work properly only with the identified
component or service.
Sec. 1051.130 What installation instructions must I give to vehicle
manufacturers?
(a) If you sell an engine for someone else to install in a
recreational vehicle, give the engine buyer written instructions for
installing it consistent with the requirements of this part. Include
all information necessary to ensure that engines installed this way
will meet emission standards.
(b) These instructions must have the following information:
(1) Include the heading: ``Emission-related installation
instructions''.
[[Page 68387]]
(2) State: ``Failing to follow these instructions when installing a
certified engine in a recreational vehicle may violate federal law (40
CFR 1068.105(b)), and subject you to fines or other penalties as
described in the Clean Air Act.''.
(3) Describe any other instructions needed to install an exhaust
aftertreatment device consistent with your application for
certification.
(4) Describe the steps needed to comply with the evaporative
emission standards in Sec. 1051.110.
(5) Describe any limits on the range of applications needed to
ensure that the engine operates consistently with your application for
certification. For example, if your engines are certified only to the
snowmobile standards, tell vehicle manufacturers not to install the
engines in other vehicles.
(6) Describe any other instructions to make sure the installed
engine will operate according to any design specifications you describe
in your application for certification.
(7) State: ``If you install the engine in a way that makes the
engine's emission control information label hard to read during normal
engine maintenance, you must place a duplicate label on the vehicle, as
described in 40 CFR 1068.105.''.
(c) You do not need installation instructions for engines you
install in your own vehicles.
Sec. 1051.135 How must I label and identify the vehicles I produce?
Each of your vehicles must have three labels: a vehicle
identification number as described in paragraph (a) of this section, an
emission control information label as described in paragraphs (b)
through (e) of this section, and a consumer information label as
described in paragraph (g) of this section.
(a) Assign each production vehicle a unique identification number
and permanently and legibly affix, stamp, or engrave it on the vehicle.
(b) At the time of manufacture, add a permanent label identifying
the emission controls for each vehicle. This is the vehicle's
``emission control information label.'' To meet labeling requirements,
do the following things:
(1) Attach the label in one piece so it is not removable without
being destroyed or defaced.
(2) Design and produce it to be durable and readable for the
vehicle's entire life.
(3) Secure it to a part of the vehicle (or engine) needed for
normal operation and not normally requiring replacement.
(4) Write it in block letters in English.
(5) Attach the label in a location where it can be easily read.
(c) On your label, do these things:
(1) Include the heading ``EMISSION CONTROL INFORMATION''.
(2) Include your full corporate name and trademark.
(3) State: ``THIS VEHICLE IS CERTIFIED TO OPERATE ON [specify
operating fuel or fuels].''.
(4) Identify the emission-control system; your identifiers must use
names and abbreviations consistent with SAE J1930 (incorporated by
reference in Sec. 1051.810).
(5) List all requirements for fuel and lubricants.
(6) State the date of manufacture [DAY (optional), MONTH, and
YEAR]; if you stamp it on the engine and print it in the owner's
manual, you may omit this information from the emission control
information label.
(7) State: ``THIS VEHICLE MEETS U.S. ENVIRONMENTAL PROTECTION
AGENCY REGULATIONS FOR [MODEL YEAR]
[SNOWMOBILES or OFF-ROAD
MOTORCYCLES or ATVs].''.
(8) Include EPA's standardized designation for the engine family.
(9) State the engine's displacement (in liters) and maximum brake
power. You do not need to include the engine's displacement and power
on the emission control information label if the vehicle is permanently
labeled with a unique model name that corresponds to a specific
displacement/power configuration.
(10) State the engine's useful life if it is different than the
minimum value.
(11) List specifications and adjustments for engine tuneups; show
the proper position for the transmission during tuneup and state which
accessories should be operating.
(12) Identify the emission standards or family emission limits to
which you have certified the engine.
(d) Some of your engines may need more information on the emission
control information label. If you produce an engine or vehicle that we
exempt from the requirements of this part, see subpart G of this part
and 40 CFR part 1068, subparts C and D, for more label information.
(e) Some engines may not have enough space for an emission control
information label with all the required information. In this case, you
may omit the information required in paragraphs (c)(3), (c)(4), and
(c)(5) of this section if you print it in the owner's manual instead.
(f) If you are unable to meet these labeling requirements, you may
ask us to modify them consistent with the intent of this section.
(g) Label every vehicle certified under this part with a removable
hang-tag showing its emission characteristics relative to other models.
The label should be attached securely to the vehicle before it is
offered for sale in such a manner that it would not be accidentally
removed prior to sale. Use the applicable equations of this paragraph
(g) to determine the normalized emission rate (NER) from the FEL for
your vehicle. If the vehicle is certified without using the averaging
provisions of subpart H, use the final deteriorated emission level.
Round the resulting normalized emission rate for your vehicle to the
nearest whole number. We may specify a standardized format for labels.
At a minimum, the tag should include: The manufacturer's name, vehicle
model name, engine description (500 cc two-stroke with DFI), the NER,
and a brief explanation of the scale (for example, note that 0 is the
cleanest and 10 is the least clean).
(1) For snowmobiles, use the following equation:
NER = 16.61 x log(2.667 x HC + CO) - 38.22
Where:
HC and CO are the cycle-weighted FELs (or emission rates) for
hydrocarbons and carbon monoxide in g/kW-hr.
(2)(i) For off-highway motorcycles with HC+NOX emissions
less than or equal to 2.0 g/km, use the following equation:
(NER = 2.500 x (HC + NOX)
Where:
HC +NOX is the FEL (or the sum of the cycle-weighted
emission rates) for hydrocarbons and oxides of nitrogen in g/km.
(ii) For off-highway motorcycles with HC+NOX emissions
greater than 2.0 g/km, use the following equation:
NER = 5.000 x log(HC + NOX) + 3.495
Where:
HC +NOX is the FEL (or the sum of the cycle-weighted
emission rates) for hydrocarbons and oxides of nitrogen in g/km.
(3)(i) For ATVs with HC+NOX emissions less than or equal
to 1.5 g/km, use the following equation:
NER = 3.333 x (HC + NOX)
Where:
HC +NOX is the FEL (or the sum of the cycle-weighted
emission rates) for hydrocarbons and oxides of nitrogen in g/km.
(ii) For ATVs with HC+NOX emissions greater than 1.5 g/
km, use the following equation:
NER = 4.444 x log(HC + NOX) + 4.217
Where:
HC +NOX is the FEL (or the sum of the cycle-weighted
emission rates) for hydrocarbons and oxides of nitrogen in g/km.
[[Page 68388]]
Sec. 1051.145 What provisions apply only for a limited time?
Apply the following provisions instead of others in this part for
the periods and circumstances specified in this section.
(a) Provisions for small-volume manufacturers. Special provisions
apply to you if you are a small-volume manufacturer subject to the
requirements of this part. Contact us before 2006 if you intend to use
these provisions.
(1) You may delay complying with otherwise applicable emission
standards (and other requirements) for two model years.
(2) If you are a small-volume manufacturer of snowmobiles, only 50
percent of the models you produce (instead of all of the models you
produce) must meet emission standards in the first two years they apply
to you as a small-volume manufacturer, as described in paragraph (a)(1)
of this section. For example, this alternate phase-in allowance would
allow small-volume snowmobile manufacturers to comply with the Phase 1
exhaust standards by certifying 50 percent of their snowmobiles in
2008, 50 percent of their snowmobiles in 2009, and 100 percent in 2010.
(3) Your vehicles for model years before 2011 may be exempt from
the exhaust standards of this part if you meet the following criteria:
(i) Produce your vehicles by installing engines covered by a valid
certificate of conformity under 40 CFR part 90 that shows the engines
meet standards for Class II engines for each engine's model year.
(ii) Do not change the engine in a way that we could reasonably
expect to increase its exhaust emissions.
(iii) The engine meets all applicable requirements from 40 CFR part
90. This applies to engine manufacturers, vehicle manufacturers who use
these engines, and all other persons as if these engines were not used
in recreational vehicles.
(iv) Demonstrate that fewer than 50 percent of the engine model's
total sales, from all companies, are used in recreational vehicles
regulated under this part.
(4) All vehicles certified or exempted under this paragraph (a)
must be labeled according to our specifications. The label must include
the following:
(i) The heading ``EMISSION CONTROL INFORMATION''.
(ii) Your full corporate name and trademark.
(iii) A description of the provisions under which the vehicle is
either exempted or certified.
(iv) Other information that we specify to you in writing.
(b) Optional emission standards for ATVs. To meet ATV standards for
model years before 2009, you may apply the exhaust emission standards
by model year in paragraph (b)(1) of this section while measuring
emissions using the engine-based test procedures in 40 CFR part 1065
instead of the chassis-based test procedures in 40 CFR part 86.
(1) Follow Table 1 of this section for exhaust emission standards,
while meeting all the other requirements of Sec. 1051.107. You may use
emission credits to show compliance with these standards (see subpart H
of this part). You may not exchange emission credits with engine
families meeting the standards in Sec. 1051.107(a). You may also not
exchange credits between engine families certified to the standards for
engines above 225 cc and engine families certified to the standards for
engines below 225 cc. The phase-in percentages in the table specify the
percentage of your U.S.-directed production that must comply with the
emission standards for those model years. Table 1 follows:
Table 1 of Sec. 1051.145.--Optional Exhaust Emission Standards for ATVs (g/kW-hr)
----------------------------------------------------------------------------------------------------------------
Emission standards Maximum
-------------------------- allowable
family
Engine displacement Model year Phase-in emission
(percent) HC+NOX CO limits
------------
HC+NOX
----------------------------------------------------------------------------------------------------------------
2006.................. 50 16.1 400 32.2
-------------------------
<225 cc............................. 2007 and 2008......... 100 16.1 400 32.2
-------------------------
2006.................. 50 13.4 400 26.8
-------------------------
£=225 cc.................. 2007 and 2008......... 100 13.4 400 26.8
----------------------------------------------------------------------------------------------------------------
(2) Measure emissions by testing the engine on a dynamometer with
the steady-state duty cycle described in Table 2 of this section.
(i) During idle mode, hold the speed within your specifications,
keep the throttle fully closed, and keep engine torque under 5 percent
of the peak torque value at maximum test speed.
(ii) For the full-load operating mode, operate the engine at its
maximum fueling rate.
(iii) See part 1065 of this chapter for detailed specifications of
tolerances and calculations.
(iv) Table 2 follows:
Table 2 of Sec. 1051.145.--6-Mode Duty Cycle for Recreational Engines
----------------------------------------------------------------------------------------------------------------
Torque
Engine speed (percent of
Mode No. (percent of maximum test Minimum time in Weighting
maximum test torque at test mode (minutes) factors
speed) speed)
----------------------------------------------------------------------------------------------------------------
1............................................ 85 100 5.0 0.09
----------------------------------------------
2............................................ 85 75 5.0 0.20
[[Page 68389]]
----------------------------------------------
3............................................ 85 50 5.0 0.29
----------------------------------------------
4............................................ 85 25 5.0 0.30
----------------------------------------------
5............................................ 85 10 5.0 0.07
----------------------------------------------
6............................................ Idle 0 5.0 0.05
----------------------------------------------------------------------------------------------------------------
(3) For ATVs certified to the standards in this paragraph (b) use
the following equation to determine the normalized emission rate
required by Sec. 1051.135(g):
NER = 9.898 x log(HC + NOX - 4.898
Where:
HC +NOX is the sum of the cycle-weighted emission
rates for hydrocarbons and oxides of nitrogen in g/kW-hr.
(c) Production-line testing. Vehicles certified to the Phase 1 or
Phase 2 standards in Sec. 1051.103, or the Phase 1 standards in
Sec. Sec. 1051.105 or 1051.107 are exempt from the production-line
testing requirements of subpart D of this part if they are certified
without participating in the emission averaging, banking and trading
program described in Subpart H of this part.
(d) Phase-in flexibility. For model years before 2014, if you make
a good faith effort to comply, but fail to meet the sales requirements
of this part during a phase-in period for new standards, or fail to
meet the average emission standards, we may approve an alternative
remedy to offset the emission reduction deficit using future emission
credits under this part. To apply for this, you must:
(1) Submit a plan during the certification process for the first
model year of the phase-in showing how you project to meet the sales
requirement of the phase-in.
(2) Notify us less than 30 days after you determine that you are
likely to fail to comply with the sales requirement of the phase-in.
(3) Propose a remedy that will achieve equivalent or greater
emission reductions compared to the specified phase-in requirements,
and that will offset the deficit within one model year.
(e) Snowmobile testing. You may use the raw sampling procedures
described in 40 CFR part 91, subparts D and E, for emission testing of
snowmobiles for model years prior to 2010. For later model years, you
may use these procedures if you show that they produce emission
measurements equivalent to the otherwise specified test procedures.
(f) Early credits. Snowmobile manufacturers may generate early
emission credits in one of the following ways, by certifying some or
all of their snowmobiles prior to 2006. Credit generating snowmobiles
must meet all other applicable requirements of this part. No early
credits may be generated by off-highway motorcycles or ATVs.
(1) You may certify one or more snowmobile engine families to FELs
(HC and CO) below the numerical level of the Phase 2 standards prior to
the date when compliance with the Phase 1 standard is otherwise
required. Credits are calculated relative to the Phase 2 standards.
Credits generated under this paragraph (f)(1) may be used at any time
before 2012.
(2) You may certify a snowmobile engine family to FELs (HC and CO)
below the numerical level of the Phase 1 standards prior to the date
when compliance with the Phase 1 standard is otherwise required.
Credits are calculated relative to the Phase 1 standards. Credits
generated under this paragraph (f)(2) may only be used for compliance
with the Phase 1 standards. You may generate credits under this
paragraph (f)(2) without regard to whether the FELs are above or below
the numerical level of the Phase 2 standards.
(g) Pull-ahead option for permeation emissions. Manufacturers
choosing to comply with an early tank permeation standard of 3.0 g/
m\2\/day prior to model year 2008 may be allowed to delay compliance
with the 1.5 g/m\2\/day standard, for an equivalent number of tanks,
subject to the following provisions:
(1) Pull-ahead tanks meeting the 3.0 g/m\2\/day standard must be
certified and must meet all applicable requirements other than those
limited to compliance with the exhaust standards.
(2) Tanks for which compliance with the 1.5 g/m\2\/day standard is
delayed must meet the 3.0 g/m\2\/day standard.
(3) You may delay compliance with the 1.5 g/m\2\/day standard for
one tank for one year for each tank-year of credit generated early.
(4) You may not use credits for a tank that is larger than the tank
from which you generated the credits.
Subpart C--Certifying Engine Families
Sec. 1051.201 What are the general requirements for submitting a
certification application?
(a) Send us an application for a certificate of conformity for each
engine family. Each application is valid for only one model year.
(b) The application must not include false or incomplete statements
or information (see Sec. 1051.255).
(c) We may choose to ask you to send us less information than we
specify in this subpart, but this would not change your recordkeeping
requirements.
(d) Use good engineering judgment for all decisions related to your
application (see Sec. 1068.5 of this chapter).
(e) An authorized representative of your company must approve and
sign the application.
Sec. 1051.205 What must I include in my application?
In your application, do all the following things unless we ask you
to send us less information:
(a) Describe the engine family's specifications and other basic
parameters of the vehicle design. List the types of fuel you intend to
use to certify the engine family (for example, gasoline, liquefied
petroleum gas, methanol, or natural gas). List vehicle configurations
and model names that are included in the engine family.
(b) Explain how the emission-control systems operate.
(1) Describe in detail all the system components for controlling
exhaust emissions, including auxiliary emission-control devices and all
fuel-system components you will install on any production or test
vehicle or engine. Explain why any auxiliary emission-control devices
are not defeat devices (see Sec. 1051.115(f)). Do not include
[[Page 68390]]
detailed calibrations for components unless we ask for them.
(2) Describe the evaporative emission controls.
(c) Describe the vehicles or engines you selected for testing and
the reasons for selecting them.
(d) Describe any special or alternate test procedures you used (see
Sec. 1051.501).
(e) Describe how you operated the engine or vehicle prior to
testing, including the duty cycle and the number of engine operating
hours used to stabilize emission levels, and any scheduled maintenance
you performed.
(f) List the specifications of the test fuels to show that they
fall within the required ranges.
(g) Identify the engine family's useful life.
(h) Propose maintenance and use instructions for the ultimate buyer
of each new vehicle (see Sec. 1051.125).
(i) Propose emission-related installation instructions if you sell
engines for someone else to install in a vehicle (see Sec. 1051.130).
(j) Propose an emission control information label.
(k) Present emission data to show that you meet emission standards.
(1) Present exhaust emission data for HC, NOX (as
applicable), and CO on a test vehicle or engine to show your vehicles
meet the emission standards we specify in subpart B of this part. Show
these figures before and after applying deterioration factors for each
vehicle or engine. Include test data for each type of fuel from part
1065, subpart C, of this chapter on which you intend for vehicles in
the engine family to operate (for example, gasoline, liquefied
petroleum gas, methanol, or natural gas). If we specify more than one
grade of any fuel type (for example, a summer grade and winter grade of
gasoline), you only need to submit test data for one grade, unless the
regulations of this part explicitly specify otherwise for your vehicle.
(2) Present evaporative test data for HC to show your vehicles meet
the evaporative emission standards we specify in subpart B of this
part. Show these figures before and after applying deterioration
factors for each vehicle or engine, where applicable. If you did not
perform the testing, identify the source of the test data.
(3) Note that Sec. 1051.235 and 1051.245 allows you to submit an
application in certain cases without new emission data.
(l) Report all test results, including those from invalid tests or
from any nonstandard tests (such as measurements based on exhaust
concentrations in parts per million).
(m) Identify the engine family's deterioration factors and describe
how you developed them. Present any emission test data you used for
this.
(n) Describe all adjustable operating parameters and other
adjustments (see Sec. 1051.115 (c) and (d)), including the following:
(1) The nominal or recommended setting.
(2) The intended physically adjustable range, including production
tolerances if they affect the range.
(3) The limits or stops used to establish adjustable ranges.
(4) The air-fuel ratios or jet chart specified in Sec.
1051.115(d).
(o) State that you operated your test vehicles or engines according
to the specified procedures and test parameters using the fuels
described in the application to show you meet the requirements of this
part.
(p) State unconditionally that all the vehicles (and/or engines) in
the engine family comply with the requirements of this part, other
referenced parts, and the Clean Air Act.
(q) Include estimates of U.S.-directed production volumes.
(r) Show us how to modify your production vehicles to measure
emissions in the field (see Sec. 1051.115).
(s) Add other information to help us evaluate your application if
we ask for it.
Sec. 1051.210 May I get preliminary approval before I complete my
application?
If you send us information before you finish the application, we
will review it and make any appropriate determinations listed in Sec.
1051.215(b)(1) through (5). Decisions made under this section are
considered to be preliminary approval. We will generally not disapprove
applications under Sec. 1051.215(b)(1) through (5) where we have given
you preliminary approval, unless we find new and substantial
information supporting a different decision.
(a) If you request preliminary approval related to the upcoming
model year or the model year after that, we will make a ``best-
efforts'' attempt to make the appropriate determinations as soon as
possible. We will generally not provide preliminary approval related to
a future model year more than two years ahead of time.
(b) If we have published general guidance that serves as our
determination for your situation, you may consider that to be
preliminary approval.
Sec. 1051.215 What happens after I complete my application?
(a) If any of the information in your application changes after you
submit it, amend it as described in Sec. 1051.225.
(b) We may deny your application (that is, determine that we cannot
approve it without revision) if the engine family does not meet the
requirements of this part or the Act. For example:
(1) If you inappropriately use the provisions of Sec. 1051.230(c)
or (d) to define a broader or narrower engine family, we will require
you to redefine your engine family.
(2) If we determine you did not appropriately select the useful
life as specified in Sec. 1051.103(c), Sec. 1051.105(c), or Sec.
1051.107(c), we will require you to lengthen it.
(3) If we determine you did not appropriately select deterioration
factors under Sec. 1051.240(c), we will require you to revise them.
(4) If your proposed emission control information label is
inconsistent with Sec. 1051.135, we will require you to change it (and
tell you how, if possible).
(5) If you require or recommend maintenance and use instructions
inconsistent with Sec. 1051.125, we will require you to change them.
(6) If we find any other problem with your application, we will
tell you what the problem is, and what needs to be corrected.
(c) If we determine your application is complete and shows that the
engine family meets all the requirements of this part and the Act, we
will issue a certificate of conformity for your engine family for that
model year. If we deny the application, we will explain why in writing.
You may then ask us to hold a hearing to reconsider our decision (see
Sec. 1051.820).
Sec. 1051.220 How do I amend the maintenance instructions in my
application?
Send the Designated Officer a request to amend your application for
certification for an engine family if you want to change the emission-
related maintenance instructions in a way that could affect emissions.
In your request, describe the proposed changes to the maintenance
instructions.
(a) If you are decreasing the specified level of maintenance, you
may distribute the new maintenance instructions to your customers 30
days after we receive your request, unless we disapprove your request.
We may approve a shorter time or waive this requirement.
(b) If your requested change would not decrease the specified level
of
[[Continued on page 68391]]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
]
[[pp. 68391-68440]]
Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
[[Continued from page 68390]]
[[Page 68391]]
maintenance, you may distribute the new maintenance instructions
anytime after you send your request.
(c) If you are correcting or clarifying your maintenance
instructions or if you are changing instructions for maintenance
unrelated to emission controls, the requirements of this section do not
apply.
Sec. 1051.225 How do I amend my application to include new or
modified vehicles or to change an FEL?
(a) You must amend your application for certification before you
take either of the following actions:
(1) Add a vehicle to a certificate of conformity.
(2) Make a design change for a certified engine family that may
affect emissions or an emission-related part over the vehicle's
lifetime.
(3) Modify an FEL for an engine family, as described in paragraph
(f) of this section.
(b) Send the Designated Officer a request to amend the application
for certification for an engine family. In your request, do all of the
following:
(1) Describe the vehicle model or configuration you are adding or
changing.
(2) Include engineering evaluations or reasons why the original
test vehicle or engine is or is not still appropriate.
(3) If the original test vehicle or engine for the engine family is
not appropriate to show compliance for the new or modified vehicle,
include new test data showing that the new or modified vehicle meets
the requirements of this part.
(c) You may start producing the new or modified vehicle anytime
after the time at which you send us your request (for example, the day
you mail your request). If we determine that the affected vehicles do
not meet applicable requirements, we will require you to cease
production of the vehicles and to recall and correct the vehicles at no
expense to the owner. If you choose to produce vehicles under this
paragraph, we will consider that to be consent to recall all vehicles
that we determine do not meet applicable standards and other
requirements and to remedy the nonconformity at no expense to the
owner.
(d) You must give us test data within 30 days if we ask for more
testing, or stop producing the vehicle if you are not able to do this.
You may give us an engineering evaluation instead of test data if we
agree that you can address our questions without test data.
(e) If we determine that the certificate of conformity would not
cover your new or modified vehicle, we will send you a written
explanation of our decision. In this case, you may no longer produce
these vehicles, though you may ask for a hearing for us to reconsider
our decision (see Sec. 1051.820).
(f) You may ask to change your FEL in the following cases:
(1) You may ask to raise your FEL for your engine family after the
start of production. You must use the higher FEL for the entire family
to calculate your average emission level under subpart H of this part.
In your request, you must demonstrate that you will still be able to
comply with the applicable average emission standards as specified in
subparts B and H of this part.
(2) You may ask to lower the FEL for your engine family after the
start of production only when you have test data from production
vehicles indicating that your vehicles comply with the lower FEL. You
may create a separate subfamily with the lower FEL. Otherwise, you must
use the higher FEL for the family to calculate your average emission
level under subpart H of this part.
(3) If you change the FEL during production, you must include the
new FEL on the emission control information label for all vehicles
produced after the change.
Sec. 1051.230 How do I select engine families?
(a) Divide your product line into families of vehicles that you
expect to have similar emission characteristics. Your engine family is
limited to a single model year.
(b) Group vehicles in the same engine family if they are the same
in all of the following aspects:
(1) The combustion cycle.
(2) The cooling system (water-cooled vs. air-cooled).
(3) Configuration of the fuel system (for example, port fuel
injection vs. carburetion).
(4) Method of air aspiration.
(5) The number, location, volume, and composition of catalytic
converters.
(6) Type of fuel.
(7) The number, arrangement, and approximate bore diameter of
cylinders.
(8) Evaporative emission controls.
(c) In some cases you may subdivide a group of vehicles that is
identical under paragraph (b) of this section into different engine
families. To do this under normal circumstances, you must show you
expect emission characteristics to be different during the useful life
or that any of the following engine characteristics are different:
(1) Method of actuating intake and exhaust timing (poppet valve,
reed valve, rotary valve, etc.).
(2) Location or size of intake and exhaust valves or ports.
(3) Configuration of the combustion chamber.
(4) Cylinder stroke or actual bore diameter.
(5) Exhaust system.
(d) In some cases, you may include different engines in the same
engine family, even though they are not identical with respect to the
things listed in paragraph (b) of this section.
(1) If different engines have similar emission characteristics
during the useful life, we may approve grouping them in the same engine
family.
(2) If you are a small-volume manufacturer, you may group engines
from any vehicles subject to the same emission standards into a single
engine family. This does not change any of the requirements of this
part for showing that an engine family meets emission standards.
(e) If you cannot appropriately define engine families by the
method in this section, we will define them based on features related
to emission characteristics.
(f) You may ask us to create separate families for exhaust
emissions and evaporative emissions. If we do this, list both families
on the emission control information label.
Sec. 1051.235 What emission testing must I perform for my application
for a certificate of conformity?
This section describes the emission testing you must perform to
show compliance with the emission standards in subpart B of this part
during certification.
(a) Test your emission-data vehicles using the procedures and
equipment specified in subpart F of this part. Where specifically
required or allowed, test the engine instead of the vehicle. For
evaporative emissions, test the fuel system components separate from
the vehicle.
(b) Select from each engine family a test vehicle or engine, and a
fuel system for each fuel type with a configuration that is most likely
to exceed the emission standards, using good engineering judgment,
consider the emission levels of all exhaust constituents over the full
useful life of the vehicle.
(c) You may use previously generated emission data in the following
cases:
(1) You may submit emission data for equivalent engine families
from previous years instead of doing new tests, but only if the data
show that the test vehicle or engine would meet all the requirements
for the latest vehicle or engine models. We may require you to
[[Page 68392]]
do new emission testing if we believe the latest vehicle or engine
models could be substantially different from the previously tested
vehicle or engine.
(2) You may submit emission data for equivalent engine families
performed to show compliance with other standards (such as California
standards) instead of doing new tests, but only if the data show that
the test vehicle or engine would meet all of this part's requirements.
(3) You may submit evaporative emission data measured by a fuel
system supplier. We may require you to verify that the testing was
conducted in accordance with the applicable regulations.
(d) We may choose to measure emissions from any of your test
vehicles or engines (or other vehicles or engines in the engine
family).
(1) If we do this, you must provide the test vehicle or engine at
the location we select. We may decide to do the testing at your plant
or any other facility. If we choose to do the testing at your plant,
you must schedule it as soon as possible and make available the
instruments and equipment we need.
(2) If we measure emissions on one of your test vehicles or
engines, the results of that testing become the official data for the
vehicle or engine. Unless we later invalidate this data, we may decide
not to consider your data in determining if your engine family meets
the emission standards.
(3) Before we test one of your vehicles or engines, we may set its
adjustable parameters to any point within the physically adjustable
ranges (see Sec. 1051.115(c)). We may also adjust the air-fuel ratio
within the adjustable range specified in Sec. 1051.115(d).
(4) Calibrate the test vehicle or engine within normal production
tolerances for anything not covered by Sec. 1051.115(c) and (d) of
this section.
(e) If you are a small-volume manufacturer, you may certify by
design on the basis of preexisting exhaust emission data for similar
technologies and other relevant information, and in accordance with
good engineering judgment. In those cases, you are not required to test
your vehicles.
This is called ``design-certification'' or ``certifying by
design.'' To certify by design, you must show that the technology used
on your engines is sufficiently similar to the previously tested
technology that a person reasonably familiar with emission-control
technology would believe that your engines will comply with the
emission standards.
(f) For fuel tanks that are certified based on permeability
treatments for plastic fuel tanks, you do not need to test each engine
family. However, you must use good engineering judgment to determine
permeation rates for the tanks. This requires that more than one fuel
tank be tested for each set of treatment conditions. You may not use
test data from a given tank for any other tanks that have thinner
walls. You may, however, use test data from a given tank for other
tanks that have thicker walls. This applies to both low-hour (i.e.,
baseline testing) and durability testing. Note that Sec. 1051.245
allows you to use design-based certification instead of generating new
emission data.
Sec. 1051.240 How do I demonstrate that my engine family complies
with exhaust emission standards?
(a) For certification, your engine family is considered to be in
compliance with the numerical exhaust emission standards in subpart B
of this part if all emission-data vehicles representing that family
have test results showing emission levels at or below the standards.
(b) Your engine family does not comply if any emission-data vehicle
representing that family has test results showing emission levels above
the standards for any pollutant.
(c) To compare emission levels from the emission-data vehicle with
the emission standards, apply deterioration factors (to three
significant figures) to the measured emission levels. The deterioration
factor is a number that shows the relationship between exhaust
emissions at the end of useful life and at the low-hour test point.
Section 1051.520 specifies how to test your vehicle to develop
deterioration factors that estimate the change in emissions over your
vehicle's full useful life. Small-volume manufacturers may use assigned
deterioration factors that we establish. Apply the deterioration
factors as follows:
(1) For vehicles that use aftertreatment technology, such as
catalytic converters, the exhaust deterioration factor is the ratio of
exhaust emissions at the end of useful life to exhaust emissions at the
low-hour test point. Adjust the official emission results for each
tested vehicle at the selected test point by multiplying the measured
emissions by the deterioration factor. If the factor is less than one,
use one.
(2) For vehicles that do not use aftertreatment technology, the
exhaust deterioration factor is the difference between exhaust
emissions at the end of useful life and exhaust emissions at the low-
hour test point. Adjust the official emission results for each tested
vehicle at the selected test point by adding the factor to the measured
emissions. If the factor is less than zero, use zero.
(d) After adjusting the emission levels for deterioration, round
them to the same number of decimal places as the emission standard.
Compare the rounded emission levels to the emission standard for each
test vehicle.
Sec. 1051.245 How do I demonstrate that my engine family complies
with evaporative emission standards?
(a) For certification, your engine family is considered in
compliance with the evaporative emission standards in subpart B of this
part if you do either of the following:
(1) You have test results showing permeation emission levels from
the fuel tanks and fuel lines in the family are at or below the
standards in Sec. 1051.110 throughout the useful life.
(2) You comply with the design specifications in paragraph (e) of
this section.
(b) Your engine family does not comply if any fuel tank or fuel
line representing that family has test results showing emission levels
above the standards.
(c) To compare emission levels with the emission standards, apply
deterioration factors (to three significant figures) to the measured
emission levels. The deterioration factor is a number that shows the
relationship between emissions at the end of useful life and at the
low-hour test point. For permeation emissions, the deterioration factor
is the difference between evaporative emissions at the end of useful
life and evaporative emissions at the low-hour test point. Adjust the
official emission results for each tested vehicle at the selected test
point by adding the factor to the measured emissions. If the factor is
less than zero, use zero.
(1) Section 1051.515 specifies how to test your fuel tanks to
develop deterioration factors that estimate the change in emissions
over your vehicle's full useful life. Small-volume manufacturers may
use assigned deterioration factors that we establish. Apply the
deterioration factors as follows:
(i) Calculate the deterioration factor from emission tests
performed before and after the durability tests described in Sec.
1051.515(c) and using good engineering judgment. The durability tests
described in Sec. 1051.515(c) represent the minimum requirements for
determining a deterioration factor. You may not use a deterioration
factor that is less than the difference between evaporative emissions
before and after
[[Page 68393]]
the durability tests described in Sec. 1051.515(c).
(ii) Do not apply the deterioration factor to test results for
tanks that have already undergone these durability tests.
(2) Determine the deterioration factor for fuel lines using good
engineering judgment.
(d) After adjusting the emission levels for deterioration, round
them to the same number of decimal places as the emission standard.
Compare the rounded emission levels to the emission standard for each
test vehicle.
(e) You may demonstrate for certification that your engine family
complies with the evaporative emission standards by demonstrating that
you use the following control technologies:
(1) For certification to the standards specified in Sec.
1051.110(a) with the control technologies shown in the following table:
Table 1 of Sec. 1051.245.--Design-certification Technologies for
Controlling Tank Permeation
------------------------------------------------------------------------
If the tank permeability control Then you may design-certify with
technology is . . . a tank emission level of . . .
------------------------------------------------------------------------
(i) A metal fuel tank with no non- 1.5 g/m 2/day.
metal gaskets or with gaskets made
from a low-permeability material 1.
(ii) A metal fuel tank with non-metal 1.5 g/m 2/day.
gaskets with an exposed surface area
of 1000 mm 2 or less.
------------------------------------------------------------------------
\1\ Permeability of 10 g/m 2/day or less according to ASTM D 814-95
(incorporated by reference in Sec. 1051.810).
(2) For certification to the standards specified in Sec.
1051.110(b) with the control technologies shown in the following table:
Table 2 of Sec. 1051.245.--Design-certification Technologies for
Controlling Fuel-line Permeation
------------------------------------------------------------------------
Then you may design-certify with
If the fuel-line permeability control a fuel line permeation emission
technology is . . . jennifer level of . . .
------------------------------------------------------------------------
(i) Hose meeting Category 1 permeation 15 g/m2/day.
specifications in SAE J2260
(incorporated by reference in Sec.
1051.810).
---------------------------------------
(ii) Hose meeting the R11-A or R12 15 g/m2/day.
permeation specifications in SAE J30
(incorporated by reference in Sec.
1051.810).
------------------------------------------------------------------------
(3) We may establish additional design certification options where
we find that new test data demonstrate that the use of other technology
designs will ensure compliance with the applicable emission standards.
Sec. 1051.250 What records must I keep and make available to EPA?
(a) Organize and maintain the following records to keep them
readily available; we may review these records at any time:
(1) A copy of all applications and any summary information you sent
us.
(2) Any of the information we specify in Sec. 1051.205 that you
did not include in your application.
(3) A detailed history of each emission-data vehicle. In each
history, describe all of the following:
(i) The emission-data vehicle's construction, including its origin
and buildup, steps you took to ensure that it represents production
vehicles, any components you built specially for it, and all emission-
related components.
(ii) How you accumulated vehicle or engine operating hours,
including the dates and the number of hours accumulated.
(iii) All maintenance (including modifications, parts changes, and
other service) and the dates and reasons for the maintenance.
(iv) All your emission tests, including documentation on routine
and standard tests, as specified in part 1065 of this chapter or other
applicable test procedures regulations, and the date and purpose of
each test.
(v) All tests to diagnose engine or emission-control performance,
giving the date and time of each and the reasons for the test.
(vi) Any other significant events.
(b) Keep routine data from emission tests (such as test cell
temperatures and relative humidity readings) for one year after we
issue the associated certificate of conformity. Keep all other
information specified in paragraph (a) of this section for eight years
after we issue your certificate.
(c) Store these records in any format and on any media, as long as
you can promptly send us organized, written records in English if we
ask for them.
(d) Send us copies of any maintenance instructions or explanations
if we ask for them.
Sec. 1051.255 When may EPA deny, revoke, or void my certificate of
conformity?
(a) We may deny your application for certification if your engine
family fails to comply with emission standards or other requirements of
the regulation or the Act. Our decision may be based on any information
available to us showing you do not meet emission standards or other
requirements, including any testing that we conduct under paragraph (g)
of this section. If we deny your application, we will explain why in
writing.
(b) In addition, we may deny your application or revoke your
certificate if you do any of the following:
(1) Refuse to comply with any testing or reporting requirements.
(2) Submit false or incomplete information (paragraph (d) of this
section applies if this is fraudulent).
(3) Render inaccurate any test data.
(4) Deny us from completing authorized activities despite our
presenting a warrant or court order (see Sec. 1068.20 of this
chapter).
(5) Produce vehicle or engines for importation into the United
States at a location where local law prohibits us from carrying out
authorized activities.
(c) We may void your certificate if you do not keep the records we
require or do not give us information when we ask for it.
(d) We may void your certificate if we find that you intentionally
submitted false or incomplete information.
(e) We may void your certificate for any family certified to an FEL
above the allowable average if you fail to show in your end-of-year
report that your average emission levels are below the
[[Page 68394]]
applicable standards in subpart B of this part, or that you have
sufficient credits to offset a credit deficit for the model year.
(f) If we deny your application or revoke or void your certificate,
you may ask for a hearing (see Sec. 1051.820). Any such hearing will
be limited to substantial and factual issues.
(g) We may conduct confirmatory testing of your vehicles as part of
certification. We may deny your application for certification or revoke
your certificate if your vehicles fail to comply with emission
standards or other requirements during confirmatory testing.
Subpart D--Testing Production-line Engines
Sec. 1051.301 When must I test my production-line vehicles or
engines?
(a) If you certify vehicles to the standards of this part, you must
test them as described in this subpart. If your vehicle is certified to
g/kW-hr standards, then test the engine; otherwise, test the vehicle.
The provisions of this subpart do not apply to small-volume
manufacturers.
(b) We may suspend or revoke your certificate of conformity for
certain engine families if your production-line vehicles or engines do
not meet the requirements of this part or you do not fulfill your
obligations under this subpart (see Sec. Sec. 1051.325 and 1051.340).
(c) Other requirements apply to vehicles and engines that you
produce. Other regulatory provisions authorize us to suspend, revoke,
or void your certificate of conformity, or order recalls for engines
families without regard to whether they have passed these production-
line testing requirements. The requirements of this subpart do not
affect our ability to do selective enforcement audits, as described in
part 1068 of this chapter. Individual vehicles and engines in families
that pass these production-line testing requirements must also conform
to all applicable regulations of this part and part 1068 of this
chapter.
(d) You may ask to use an alternate program for testing production-
line vehicles or engines. In your request, you must show us that the
alternate program gives equal assurance that your products meet the
requirements of this part. If we approve your alternate program, we may
waive some or all of this subpart's requirements.
(e) If you certify an engine family with carryover emission data,
as described in Sec. 1051.235(c), and these equivalent engine families
consistently pass the production-line testing requirements over the
preceding two-year period, you may ask for a reduced testing rate for
further production-line testing for that family. The minimum testing
rate is one vehicle or engine per engine family. If we reduce your
testing rate, we may limit our approval to a any number of model years.
In determining whether to approve your request, we may consider the
number of vehicles or engines that have failed the emission tests.
(f) We may ask you to make a reasonable number of production-line
vehicles or engines available for a reasonable time so we can test or
inspect them for compliance with the requirements of this part.
(g) The requirements of this subpart do not apply to engine
families certified under the provisions of Sec. 1051.630.
Sec. 1051.305 How must I prepare and test my production-line vehicles
or engines?
(a) Test procedures. Test your production-line vehicles or engines
using the applicable testing procedures in subpart F of this part to
show you meet the emission standards in subpart B of this part.
(b) Modifying a test vehicle or engine. Once a vehicle or engine is
selected for testing (see Sec. 1051.310), you may adjust, repair,
prepare, or modify it or check its emissions only if one of the
following is true:
(1) You document the need for doing so in your procedures for
assembling and inspecting all your production vehicles or engines and
make the action routine for all the vehicles or engines in the engine
family.
(2) This subpart otherwise specifically allows your action.
(3) We approve your action in advance.
(c) Malfunction. If a vehicle or engine malfunction prevents
further emission testing, ask us to approve your decision to either
repair it or delete it from the test sequence.
(d) Setting adjustable parameters. Before any test, we may adjust
or require you to adjust any adjustable parameter to any setting within
its physically adjustable range.
(1) We may adjust idle speed outside the physically adjustable
range as needed only until the vehicle or engine has stabilized
emission levels (see paragraph (e) of this section). We may ask you for
information needed to establish an alternate minimum idle speed.
(2) We may make or specify adjustments within the physically
adjustable range by considering their effect on emission levels, as
well as how likely it is someone will make such an adjustment with in-
use vehicles.
(3) We may adjust the air-fuel ratio within the adjustable range
specified in Sec. 1051.115(d).
(e) Stabilizing emission levels. Before you test production-line
vehicles or engines, you may operate the vehicle or engine to stabilize
the emission levels. Using good engineering judgment, operate your
vehicles or engines in a way that represents the way they will be used.
You may operate each vehicle or engine for no more than the greater of
two periods:
(1) 50 hours.
(2) The number of hours you operated the emission-data vehicle used
for certifying the engine family (see 40 CFR part 1065, subpart E, or
the applicable regulations governing how you should prepare your test
vehicle or engine).
(f) Damage during shipment. If shipping a vehicle or engine to a
remote facility for production-line testing makes necessary an
adjustment or repair, you must wait until after the after the initial
emission test to do this work. We may waive this requirement if the
test would be impossible or unsafe, or if it would permanently damage
the vehicle or engine. Report to us, in your written report under Sec.
1051.345, all adjustments or repairs you make on test vehicles or
engines before each test.
(g) Retesting after invalid tests. You may retest a vehicle or
engine if you determine an emission test is invalid. Explain in your
written report reasons for invalidating any test and the emission
results from all tests. If you retest a vehicle or engine, you may ask
us to substitute results of the new tests for the original ones. You
must ask us within ten days of testing. We will generally answer within
ten days after we receive your information.
Sec. 1051.310 How must I select vehicles or engines for production-
line testing?
(a) Use test results from two vehicles or engines for each engine
family to calculate the required sample size for the test period.
Update this calculation with each test.
(1) For engine families with projected annual sales of at least
1600, the test periods are consecutive quarters (3 months). If your
annual production period is less than 12 months long, define your test
periods by dividing your annual production period into approximately
equal segments of 70 to 125 calendar days.
(2) For engine families with projected annual sales below 1600, the
test period is the whole model year.
(b) Early in each test period, randomly select and test an engine
from the end of the assembly line for each engine family.
[[Page 68395]]
(1) In the first test period for newly certified engines, randomly
select and test one more engine. Then, calculate the required sample
size for the test period as described in paragraph (c) of this section.
(2) In later test periods or for engine families relying on
previously submitted test data, combine the new test result with the
last test result from the previous test period. Then, calculate the
required sample size for the new test period as described in paragraph
(c) of this section.
(c) Calculate the required sample size for each engine family.
Separately calculate this figure for HC, NOX (or
HC+NOX), and CO (and other regulated pollutants). The
required sample size is the greater of these calculated values. Use the
following equation:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.008
Where:
N = Required sample size for the model year.
t95 = 95% confidence coefficient, which depends on the
number of tests completed, n, as specified in the table in paragraph
(c)(1) of this section. It defines 95% confidence intervals for a one-
tail distribution.
x = Mean of emission test results of the sample.
STD = Emission standard (or family emission limit, if applicable).
[sigma]
= Test sample standard deviation (see paragraph (c)(2) of this
section).
(1) Determine the 95% confidence coefficient, t95, from
the following table:
------------------------------------------------------------------------
n t95 n t95 n t95
------------------------------------------------------------------------
2 6.31 12 1.80 22 1.72
3 2.92 13 1.78 23 1.72
4 2.35 14 1.77 24 1.71
5 2.13 15 1.76 25 1.71
6 2.02 16 1.75 26 1.71
7 1.94 17 1.75 27 1.71
8 1.90 18 1.74 28 1.70
9 1.86 19 1.73 29 1.70
10 1.83 20 1.73 30+ 1.70
11 1.81 21 1.72 .......... ..........
------------------------------------------------------------------------
(2) Calculate the standard deviation, [sigma], for the test sample
using the following formula:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.009
Where:
Xi = Emission test result for an individual vehicle or
engine.
n = The number of tests completed in an engine family.
(d) Use final deteriorated test results to calculate the variables
in the equations in paragraph (c) of this section (see Sec.
1051.315(a)).
(e) After each new test, recalculate the required sample size using
the updated mean values, standard deviations, and the appropriate 95-
percent confidence coefficient.
(f) Distribute the remaining vehicle or engine tests evenly
throughout the rest of the year. You may need to adjust your schedule
for selecting vehicles or engines if the required sample size changes.
Continue to randomly select vehicles or engines from each engine
family; this may involve testing vehicles or engines that operate on
different fuels.
(g) Continue testing any engine family for which the sample mean,
x, is greater than the emission standard. This applies if the sample
mean for either HC, NOX (or HC+NOX), or CO (or
other regulated pollutants) is greater than the emission standard.
Continue testing until one of the following things happens:
(1) The sample size, n, for an engine family is greater than the
required sample size, N, and the sample mean, x, is less than or equal
to the emission standard. For example, if N = 3.1 after the third test,
the sample-size calculation does not allow you to stop testing.
(2) The engine family does not comply according to Sec. 1051.325.
(3) You test 30 vehicles or engines from the engine family.
(4) You test one percent of your projected annual U.S.-directed
production volume for the engine family.
(5) You choose to declare that the engine family fails the
requirements of this subpart. (h) If the sample-size calculation allows
you to stop testing for a pollutant, you must continue measuring
emission levels of that pollutant for any additional tests required
under this section. However, you need not continue making the
calculations specified in this section for that pollutant. This
paragraph does not affect the requirements in section Sec. 1051.320.
(i) You may elect to test more randomly chosen vehicles or engines
than we require. Include these vehicles or engines in the sample-size
calculations.
Sec. 1051.315 How do I know when my engine family fails the
production-line testing requirements?
This section describes the pass-fail criteria for the production-
line testing requirements. We apply this criteria on an engine family
basis. See Sec. 1051.320 for the requirements that apply to individual
vehicles or engines that fail a production-line test. (a) Calculate
your test results. Round them to the number of decimal places in the
emission standard expressed to one more decimal place.
(1) Initial and final test results. Calculate and round the test
results for each vehicle or engine. If you do several tests on a
vehicle or engine, calculate the initial test results, then add them
together and divide by the number of tests and round for the final test
results on that vehicle or engine.
(2) Final deteriorated test results. Apply the deterioration factor
for the engine family to the final test results (see Sec.
1051.240(c)).
(b) Construct the following CumSum Equation for each engine family
for HC, NOX (or HC+NOX), and CO emissions (and
other regulated pollutants):
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.010
Where:
Ci = The current CumSum statistic.
Ci-1 = The previous CumSum statistic. For the first test,
the CumSum statistic is 0 (i.e. C1 = 0).
Xi = The current emission test result for an individual
vehicle or engine.
STD = Emission standard.
(c) Use final deteriorated test results to calculate the variables
in the equation in paragraph (b) of this section (see Sec.
1051.315(a)).
(d) After each new test, recalculate the CumSum statistic.
[[Page 68396]]
(e) If you test more than the required number of vehicles or
engines, include the results from these additional tests in the CumSum
Equation.
(f) After each test, compare the current CumSum statistic,
Ci, to the recalculated Action Limit, H, defined as H = 5.0
x [sigma].
(g) If the CumSum statistic exceeds the Action Limit in two
consecutive tests, the engine family fails the production-line testing
requirements of this subpart. Tell us within ten working days if this
happens. You may request to amend the application for certification to
raise the FEL of the engine family at this point if you meet the
requirements of Sec. 1051.225(f).
(h) If you amend the application for certification for an engine
family under Sec. 1051.225, do not change any previous calculations of
sample size or CumSum statistics for the model year.
Sec. 1051.320 What happens if one of my production-line vehicles or
engines fails to meet emission standards?
(a) If you have a production-line vehicle or engine with final
deteriorated test results exceeding one or more emission standards (see
Sec. 1051.315(a)), the certificate of conformity is automatically
suspended for that failing vehicle or engine. You must take the
following actions before your certificate of conformity can cover that
vehicle or engine:
(1) Correct the problem and retest the vehicle or engine to show it
complies with all emission standards.
(2) Include in your written report a description of the test
results and the remedy for each vehicle or engine (see Sec. 1051.345).
(b) You may request to amend the application for certification to
raise the FEL of the entire engine family at this point (see Sec.
1051.225).
Sec. 1051.325 What happens if an engine family fails the production-
line requirements?
(a) We may suspend your certificate of conformity for an engine
family if it fails under Sec. 1051.315. The suspension may apply to
all facilities producing vehicles or engines from an engine family,
even if you find noncompliant vehicles or engines only at one facility.
(b) We will tell you in writing if we suspend your certificate in
whole or in part. We will not suspend a certificate until at least 15
days after the engine family fails. The suspension is effective when
you receive our notice.
(c) Up to 15 days after we suspend the certificate for an engine
family, you may ask for a hearing (see Sec. 1051.820). If we agree
before a hearing that we used erroneous information in deciding to
suspend the certificate, we will reinstate the certificate.
(d) Section 1051.335 specifies steps you must take to remedy the
cause of the production-line failure. All the vehicles you have
produced since the end of the last test period are presumed
noncompliant and should be addressed in your proposed remedy. We may
require you to apply the remedy to engines produced earlier if we
determine that the cause of the failure is likely to have affected the
earlier engines.
(e) You may request to amend the application for certification to
raise the FEL of the engine family before or after we suspend your
certificate if you meet the requirements of Sec. 1051.225(f).
Sec. 1051.330 May I sell vehicles from an engine family with a
suspended certificate of conformity?
You may sell vehicles that you produce after we suspend the engine
family's certificate of conformity under Sec. 1051.315 only if one of
the following occurs:
(a) You test each vehicle or engine you produce and show it
complies with emission standards that apply.
(b) We conditionally reinstate the certificate for the engine
family. We may do so if you agree to recall all the affected vehicles
and remedy any noncompliance at no expense to the owner if later
testing shows that the engine family still does not comply.
Sec. 1051.335 How do I ask EPA to reinstate my suspended certificate?
(a) Send us a written report asking us to reinstate your suspended
certificate. In your report, identify the reason for noncompliance,
propose a remedy for the engine family, and commit to a date for
carrying it out. In your proposed remedy include any quality control
measures you propose to keep the problem from happening again.
(b) Give us data from production-line testing that shows the
remedied engine family complies with all the emission standards that
apply.
Sec. 1051.340 When may EPA revoke my certificate under this subpart
and how may I sell these vehicles again?
(a) We may revoke your certificate for an engine family in the
following cases:
(1) You do not meet the reporting requirements.
(2) Your engine family fails to comply with the requirements of
this subpart and your proposed remedy to address a suspended
certificate under Sec. 1051.325 is inadequate to solve the problem or
requires you to change the vehicle's design or emission-control system.
(b) To sell vehicles from an engine family with a revoked
certificate of conformity, you must modify the engine family and then
show it complies with the requirements of this part.
(1) If we determine your proposed design change may not control
emissions for the vehicle's full useful life, we will tell you within
five working days after receiving your report. In this case we will
decide whether production-line testing will be enough for us to
evaluate the change or whether you need to do more testing.
(2) Unless we require more testing, you may show compliance by
testing production-line vehicles or engines as described in this
subpart.
(3) We will issue a new or updated certificate of conformity when
you have met these requirements.
Sec. 1051.345 What production-line testing records must I send to
EPA?
Do all the following things unless we ask you to send us less
information:
(a) Within 30 calendar days of the end of each calendar quarter,
send us a report with the following information:
(1) Describe any facility used to test production-line vehicles or
engines and state its location.
(2) State the total U.S.-directed production volume and number of
tests for each engine family.
(3) Describe how you randomly selected vehicles or engines.
(4) Describe your test vehicles or engines, including the engine
family's identification and the vehicle's model year, build date, model
number, identification number, and number of hours of operation before
testing for each test vehicle or engine.
(5) Identify where you accumulated hours of operation on the
vehicles or engines and describe the procedure and schedule you used.
(6) Provide the test number; the date, time and duration of
testing; test procedure; initial test results before and after
rounding; final test results; and final deteriorated test results for
all tests. Provide the emission results for all measured pollutants.
Include information for both valid and invalid tests and the reason for
any invalidation.
(7) Describe completely and justify any nonroutine adjustment,
modification, repair, preparation, maintenance, or test for the test
vehicle or engine if you did not report it separately under this
subpart. Include the results of any emission measurements, regardless
of the procedure or type of vehicle.
(8) Provide the CumSum analysis required in Sec. 1051.315 for each
engine family.
[[Page 68397]]
(9) Report on each failed vehicle or engine as described in Sec.
1051.320.
(10) State the date the calendar quarter ended for each engine
family.
(b) We may ask you to add information to your written report, so we
can determine whether your new vehicles conform with the requirements
of this subpart.
(c) An authorized representative of your company must sign the
following statement:
We submit this report under Sections 208 and 213 of the Clean
Air Act. Our production-line testing conformed completely with the
requirements of 40 CFR part 1051. We have not changed production
processes or quality-control procedures for the engine family in a
way that might affect the emission control from production vehicles
(or engines). All the information in this report is true and
accurate, to the best of my knowledge. I know of the penalties for
violating the Clean Air Act and the regulations. (Authorized Company
Representative)
(d) Send electronic reports of production-line testing to the
Designated Officer using an approved information format. If you want to
use a different format, send us a written request with justification
for a waiver.
(e) We will send copies of your reports to anyone from the public
who asks for them. See Sec. 1051.815 for information on how we treat
information you consider confidential.
Sec. 1051.350 What records must I keep?
(a) Organize and maintain your records as described in this
section. We may review your records at any time, so it is important to
keep required information readily available.
(b) Keep paper records of your production-line testing for one full
year after you complete all the testing required for an engine family
in a model year. You may use any additional storage formats or media if
you like.
(c) Keep a copy of the written reports described in Sec. 1051.345.
(d) Keep the following additional records:
(1) A description of all test equipment for each test cell that you
can use to test production-line vehicles or engines.
(2) The names of supervisors involved in each test.
(3) The name of anyone who authorizes adjusting, repairing,
preparing, or modifying a test vehicle or engine and the names of all
supervisors who oversee this work.
(4) If you shipped the vehicle or engine for testing, the date you
shipped it, the associated storage or port facility, and the date the
vehicle or engine arrived at the testing facility.
(5) Any records related to your production-line tests that are not
in the written report.
(6) A brief description of any significant events during testing
not otherwise described in the written report or in this section.
(7) Any information specified in Sec. 1051.345 that you do not
include in your written reports.
(e) If we ask, you must give us projected or actual production
figures for an engine family. We may ask you to divide your production
figures by rated brake power, displacement, fuel type, or assembly
plant (if you produce vehicles or engines at more than one plant).
(f) Keep a list of vehicle or engine identification numbers for all
the vehicles or engines you produce under each certificate of
conformity. Give us this list within 30 days if we ask for it.
(g) We may ask you to keep or send other information necessary to
implement this subpart.
Subpart E--Testing In-use Engines [Reserved]
Subpart F--Test Procedures
Sec. 1051.501 What procedures must I use to test my vehicles or
engines?
This section describes test procedures that you use to show
compliance with the requirements of this part. See Sec. 1051.235 to
determine when testing is required for certification. See subpart D of
this part for the production-line testing requirements.
(a) Snowmobiles. For snowmobiles, use the equipment and procedures
for spark-ignition engines in part 1065 of this chapter to show your
snowmobiles meet the duty-cycle emission standards in Sec. 1051.103.
Measure HC, NOX (as applicable), CO, and CO2
emissions using the dilute sampling procedures in part 1065 of this
chapter. For steady-state testing, you may use raw-gas sampling methods
(such as those described in 40 CFR part 91), provided they have been
shown to produce measurements equivalent to the dilute sampling methods
specified in part 1065 of this chapter. Use the duty cycle in Sec.
1051.505.
(b) Motorcycles and ATVs. For motorcycles and ATVs, use the
equipment, procedures, and duty cycle in 40 CFR part 86, subpart F, to
show your vehicles meet the exhaust emission standards in Sec.
1051.105 or Sec. 1051.107. Measure HC, NOX, CO, and
CO2. If we allow you to certify ATVs based on engine
testing, use the equipment, procedures, and duty cycle described or
referenced in that section that allows engine testing. For motorcycles
with engine displacement at or below 169 cc and all ATVs, use the
driving schedule in paragraph (c) of Appendix I to 40 CFR part 86. For
all other motorcycles use the driving schedule in paragraph (b) of
Appendix I to part 86. With respect to vehicle-speed governors, test
motorcycles and ATVs in their ungoverned configuration, unless we
approve in advance testing in a governed configuration. We will only
approve testing in a governed configuration if you can show that the
governor is permanently installed on all production vehicles and is
unlikely to be removed in-use. With respect to engine-speed governors,
test motorcycles and ATVs in their governed configuration.
(c) Permeation testing. (1) Use the equipment and procedures
specified in Sec. 1051.515 to measure fuel tank permeation emissions.
(2) Prior to permeation testing of fuel hose, the hose must be
preconditioned by filling the hose with the fuel specified in (d)(3) of
this section, sealing the openings, and soaking the hose for 4 weeks at
23 [deg]C+/-5[deg]
C. To measure fuel-line permeation emissions, use
the equipment and procedures specified in SAE J30 (incorporated by
reference in Sec. 1051.810). The measurements must be performed at 23
[deg]
C using the fuel specified in paragraph (d)(3) of this section.
(d) Fuels. Use the fuels meeting the following specifications:
(1) Exhaust. Use the fuels and lubricants specified in 40 CFR part
1065, subpart C, for all the testing and service accumulation we
require in this part.
(2) Fuel Tank Permeation. (i) For the preconditioning soak
described in Sec. 1051.515(a)(1) and fuel slosh durability test
described in Sec. 1051.515(c)(4), use the fuel specified in Table 1 of
Sec. 1065.210 of this chapter blended with 10 percent ethanol by
volume. As an alternative, you may use Fuel CE10, which is Fuel C as
specified in ASTM D 471-98 (incorporated by reference in Sec.
1051.810) blended with 10 percent ethanol by volume.
(ii) For the permeation measurement test in Sec. 1051.515(b), use
the fuel specified in Table 1 of Sec. 1065.210 of this chapter. As an
alternative, you may use the fuel specified in paragraph (d)(2)(i) of
this section.
(3) Fuel Hose Permeation. Use the fuel specified in Table 1 of
Sec. 1065.210 of this chapter blended with 10 percent ethanol by
volume for permeation testing of fuel lines and tanks. As an
alternative, you may use Fuel CE10, which is Fuel C as specified in
ASTM D 471-98
[[Page 68398]]
(incorporated by reference in Sec. 1051.810) blended with 10 percent
ethanol by volume.
(e) Special procedures for engine testing. (1) You may use special
or alternate procedures, as described in Sec. 1065.10 of this chapter.
(2) We may reject data you generate using alternate procedures if
later testing with the procedures in part 1065 of this chapter shows
contradictory emission data.
(f) Special procedures for vehicle testing. (1) You may use special
or alternate procedures, as described in paragraph (f)(3) of this
section.
(2) We may reject data you generate using alternate procedures if
later testing with the otherwise specified procedures shows
contradictory emission data.
(3)(i) The test procedures specified for vehicle testing are
intended to produce emission measurements equivalent to those that
would result from measuring emissions during in-use operation using the
same vehicle configuration. If good engineering judgment indicates that
use of the procedures in this part for a vehicle would result in
measurements that are not representative of in-use operation of that
vehicle, you must notify us. If we determine that using these
procedures would result in measurements that are significantly
unrepresentative and that changes to the procedures will result in more
representative measurements that do not decrease the stringency of
emission standards or other requirements, we will specify changes to
the procedures. In your notification to us, you should recommend
specific changes you think are necessary.
(ii) You may ask to use emission data collected using other test
procedures, such as those of the California Air Resources Board or the
International Organization for Standardization. We will allow this only
if you show us that these data are equivalent to data collected using
our test procedures.
(iii) You may ask to use alternate procedures that produce
measurements equivalent to those obtained using the specified
procedures. In this case, send us a written request showing that your
alternate procedures are equivalent to the test procedures of this
part. If you prove to us that the procedures are equivalent, we will
allow you to use them. You may not use alternate procedures until we
approve them.
(iv) You may ask to use special test procedures if your vehicle
cannot be tested using the specified test procedures (for example, it
is incapable of operating on the specified transient cycle). In this
case, send us a written request showing that you cannot satisfactorily
test your engines using the test procedures of this part. We will allow
you to use special test procedures if we determine that they would
produce emission measurements that are representative of those that
would result from measuring emissions during in-use operation. You may
not use special procedures until we approve them.
Sec. 1051.505 What special provisions apply for testing snowmobiles?
Use the following special provisions for testing snowmobiles:
(a) Measure emissions by testing the engine on a dynamometer with
the steady-state duty cycle described in the following Table:
Table 1 of Sec. 1051.505.--5-Mode Duty Cycle for Snowmobiles
----------------------------------------------------------------------------------------------------------------
Torque
Engine speed (percent of
(percent of maximum test Minimum time Weighting
maximum test torque at in mode factors
speed) maximum test (minutes)
speed)
----------------------------------------------------------------------------------------------------------------
Mode number:
1........................................... 100 100 3.0 0.12
-------------------------------------------------
2........................................... 85 51 3.0 0.27
-------------------------------------------------
3........................................... 75 33 3.0 0.25
-------------------------------------------------
4........................................... 65 19 3.0 0.31
-------------------------------------------------
5........................................... Idle 0 3.0 0.05
----------------------------------------------------------------------------------------------------------------
(b) During idle mode, operate the engine with the following
parameters:
(1) Hold the speed within your specifications.
(2) Keep the throttle at the idle-stop position.
(3) Keep engine torque under 5 percent of the peak torque value at
maximum test speed.
(c) For the full-load operating mode, operate the engine at wide-
open throttle.
(d) Ambient temperatures during testing must be between 20 [deg]C
and 30 [deg]C (68 [deg]F and 86 [deg]F), or other representative test
temperatures, as specified in paragraph (g) of this section.
(e) See part 1065 of this chapter for detailed specifications of
tolerances and calculations.
(f) You may test snowmobiles at ambient temperatures below 20
[deg]C or using intake air temperatures below 20 [deg]C if you show
that such testing complies with Sec. 1065.10(c)(1) of this chapter.
You must get our approval before you begin the emission testing. For
example, the following approach would be appropriate to show that such
testing complies with Sec. 1065.10(c)(1) of this chapter:
(1) Using good engineering judgment, instrument a representative
snowmobile built with a representative engine from the family being
tested with an appropriate temperature measuring device located in the
intake air plenum where fuel spitback is not likely to occur.
(2) Choose a time and location with the following weather
conditions: windspeed less than 10 knots, no falling precipitation, air
temperature between -20 [deg]C and 0 [deg]C (-4 [deg]F and 32 [deg]F).
(3) Operate the snowmobile until its engine reaches a steady
operating temperature.
(4) Operate the snowmobile on a level surface free of other vehicle
traffic. Operate the snowmobile at each specified engine speed
corresponding to each mode in the emissions test specific to the engine
being tested. When readings are stable, record the temperature in the
intake air plenum
[[Page 68399]]
and the ambient temperature. Calculate the temperature difference
between the air in the plenum and the ambient air for each mode.
(5) Calculate the nominal intake air test temperature for each test
mode as -10 [deg]C (14 [deg]F) plus the temperature difference for the
corresponding mode determined in (g)(4) of this section.
(6) Before the emissions test, select the appropriate carburetor
jetting for -10 [deg]C (14 [deg]F) conditions according to the jet
chart. For each mode, maintain the inlet air temperature within 5
[deg]C of the corresponding modal temperature calculated in (g)(5) of
this section.
(7) Adjust other operating parameters to be consistent with
operation at -10 [deg]C (14 [deg]F). For example, this may require that
you modify the engine cooling system used in the laboratory to make its
performance representative of cold-temperature operation.
Sec. 1051.510 What special provisions apply for testing ATV engines?
[Reserved]
Sec. 1051.515 How do I test my fuel tank for permeation emissions?
Measure permeation emissions by weighing a sealed fuel tank before
and after a temperature-controlled soak.
(a) Preconditioning. To precondition your fuel tank, follow these
five steps:
(1) Fill the tank with the fuel specified in Sec.
1051.501(d)(2)(i), seal it, and allow it to soak at 28 +/-5 [deg]C for
20 weeks. Alternatively, the tank may be soaked for a shorter period of
time at a higher temperature if you can show that the hydrocarbon
permeation rate has stabilized.
(2) Determine the fuel tank's internal surface area in square-
meters accurate to at least three significant figures. You may use less
accurate estimates of the surface area if you make sure not to
overestimate the surface area.
(3) Fill the fuel tank with the test fuel specified in Sec.
1051.501(d)(2)(ii) to its nominal capacity. If you fill the tank inside
the temperature-controlled room or enclosure, do not spill any fuel.
(4) Allow the tank and its contents to equilibrate to 28+/-2
[deg]C.
(5) Seal the fuel tank using nonpermeable fittings, such as metal
or TeflonTM.
(b) Test run. To run the test, follow these nine steps for a tank
that was preconditioned as specified in paragraph (a) of this section:
(1) Weigh the sealed fuel tank and record the weight to the nearest
0.1 grams. (You may use less precise weights as long as the difference
in mass from the start of the test to the end of the test has at least
three significant figures.)
(2) Carefully place the tank within a ventilated temperature-
controlled room or enclosure. Do not spill any fuel.
(3) Close the room or enclosure and record the time.
(4) Ensure that the measured temperature in the room or enclosure
is 28+/-2 [deg]C.
(5) Leave the tank in the room or enclosure for 2 to 4 weeks,
consistent with good engineering judgment (based on the permeation
rate). Do not stop soaking before 4 weeks unless you know that you can
measure the weight loss during the test to at least three significant
figures earlier.
(6) Hold the temperature of the room or enclosure to 28+/-2 [deg]C;
measure and record the temperature at least daily.
(7) At the end of the soak period, weigh the sealed fuel tank and
record the weight to the nearest 0.1 grams. (You may use less precise
weights as long as the difference in mass from the start of the test to
the end of the test has at least three significant figures.)
(8) Subtract the weight of the tank at the end of the test from the
weight of the tank at the beginning of the test; divide the difference
by the internal surface area of the fuel tank. Divide this g/m \2\
value by the number of test days (using at least three significant
figures) to calculate the g/m \2\/day emission rate. Example: If a tank
with an internal surface area of 1.51 m \2\ weighed 31882.3 grams at
the beginning of the test and weighed 31760.2 grams after soaking for
25.03 days, then the g/m \2\/day emission rate would be: (31882.3 g-
31760.2 g)/1.51 m \2\/25.03 days = 3.23 g/m \2\/day.
(9) Round your result to the same number of decimal places as the
emission standard.
(c) Durability testing. You normally need to perform a separate
durability demonstration for each substantially different combination
of treatment approaches and tank materials. Perform these
demonstrations before an emission test by taking the following steps,
unless you can use good engineering judgment to apply the results of
previous durability testing with a different fuel system. You can
determine a deterioration factor by measuring emissions on a tank after
these durability tests if you previously tested the same tank before
the durability tests (but after the preconditioning step described in
paragraph (a) of this section). For the purposes of deterioration
factor determination, the permeation tests before and after the
durability testing must be performed on the fuel specified in Sec.
1051.501 (d)(2)(i). You may ask to exclude any of the following
durability tests if you can clearly demonstrate that it does not affect
the emissions from your fuel tank.
(1) Perform a pressure test by sealing the tank and cycling it
between +2.0 psig and -0.5 psig and back to +2.0 psig for 10,000 cycles
at a rate 60 seconds per cycle.
(2) Perform a sunlight-exposure test by exposing the tank to an
ultraviolet light of at least 0.40 W-hr/m \2\/min on the tank surface
for 15 hours per day for 4 weeks. Alternatively, the fuel tank may be
exposed to direct natural sunlight for an equivalent period of time, as
long as you ensure that the tank is exposed to at least 450 daylight
hours.
(3) Perform a slosh test by filling the tank to 40 percent of its
capacity with the fuel specified in Sec. 1051.501(d)(2)(i) and rocking
it at a rate of 15 cycles per minute until you reach one million total
cycles.
Use an angle deviation of +15[deg]
to -15[deg]
from level. This
test must be performed at a temperature of 28[deg]C +/-5[deg]
C.
(4) Following the durability testing, the fuel tank must be soaked
(as described in paragraph (a) of this section) to ensure that the
permeation rate is stable. The period of slosh testing and the period
of ultraviolet testing (if performed with fuel in the tank consistent
with paragraph (a)(1) of this section) may be considered to be part of
this soak, provided that the soak begins immediately after the slosh
testing. To determine the final permeation rate, drain and refill the
tank with fresh fuel, and repeat the test run (as described in
paragraph (b) of this section) immediately after this soak period.
(d) Flow chart. The following figure presents a flow chart for the
permeation testing described in this section, showing full test
procedure with durability testing, as well as the simplified test
procedure with an applied deterioration factor:
BILLING CODE 6560-50-P
[[Page 68400]]
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.016
BILLING CODE 6560-50-C
Sec. 1051.520 How do I perform exhaust durability testing?
This section applies for durability testing to determine
deterioration factors for exhaust emissions. Small-volume manufacturers
may omit durability testing if they use our assigned deterioration
factors that we establish based on our projection of the likely
deterioration in the performance of specific emission controls.
(a) Calculate your deterioration factor by testing a vehicle or
engine that is representative of your engine family at a low-hour test
point and the end of its useful life. You may also test at intermediate
points.
(b) Operate the vehicle or engine over a representative duty cycle
for a period at least as long as the useful life (in hours or
kilometers). You may operate the vehicle or engine continuously.
(c) You may perform critical emission-related maintenance during
durability testing, consistent with Sec. 1051.125(a). You may not
perform any other emission-related maintenance during durability
testing.
(d) Use a linear least-squares fit of your test data for each
pollutant to calculate your deterioration factor.
(e) You may ask us to allow you to use other testing methods to
determine deterioration factors, consistent with good engineering
judgment.
[[Page 68401]]
Subpart G--Compliance Provisions
Sec. 1051.601 What compliance provisions apply to vehicles and
engines subject to this part?
Engine and vehicle manufacturers, as well as owners, operators, and
rebuilders of these vehicles, and all other persons, must observe the
requirements and prohibitions in part 1068 of this chapter and the
requirements of the Act. The compliance provisions in this subpart
apply only to the vehicles and engines we regulate in this part.
Sec. 1051.605 What are the provisions for exempting vehicles from the
requirements of this part if they use engines you have certified under
the motor-vehicle program or the Large Spark-ignition program?
(a) You may ask for an exemption under this section if you are the
manufacturer of an engine certified under the motor-vehicle program or
the Large Spark-ignition program. See Sec. 1051.610 if you are not the
engine manufacturer.
(b)(1) The only requirements or prohibitions from this part that
apply to a vehicle that is exempt under this section are in this
section and Sec. 1051.610.
(2) If the vehicles do not meet the criteria listed in paragraph
(c) of this section, they will be subject to the standards and
prohibitions of this part. Producing these vehicles without a valid
exemption or certificate of conformity would violate the prohibitions
in Sec. 1068.101 of this chapter.
(3) Vehicles exempted under this section are subject to all the
requirements affecting engines and vehicles under 40 CFR part 86 or
part 1048, as applicable. The requirements and restrictions of 40 CFR
part 86 or 1048 apply to anyone manufacturing these engines, anyone
manufacturing vehicles that use these engines, and all other persons in
the same manner as if these engines were used in a motor vehicle or
other nonrecreational application.
(c) If you meet all the following criteria regarding your engine,
the vehicle using the engine is exempt under this section:
(1) The vehicle is produced using an engine or incomplete vehicle
covered by a valid certificate of conformity under 40 CFR part 86 or
part 1048.
(2) No changes are made to the certified engine or vehicle that we
could reasonably expect to increase any of its regulated emissions. For
example, if any of the following changes are made to the engine, it
does not qualify for this exemption:
(i) Any fuel system or evaporative system parameters are changed
from the certified configuration (this does not apply to refueling
emission controls).
(ii) Any other emission-related components are changed.
(iii) The engine cooling system is modified or assembled so that
temperatures or heat rejection rates are outside the original engine's
specified ranges.
(3) The engine must have the emission control information label we
require under 40 CFR part 86 or part 1048.
(4) You must demonstrate that fewer than 50 percent of the engine
model's total sales, from all companies, are used in recreational
vehicles.
(d) If you manufacture both the engine and vehicle under this
exemption, you must do all of the following to keep the exemption
valid:
(1) Make sure the original emission control information label is
intact.
(2) Add a permanent supplemental label to the engine in a position
where it will remain clearly visible after installation in the vehicle.
In your engine's emission control information label, do the following:
(i) Include the heading: ``Recreational Vehicle Emission Control
Information''.
(ii) Include your full corporate name and trademark.
(iii) State: ``THIS ENGINE WAS ADAPTED FOR RECREATIONAL USE WITHOUT
AFFECTING ITS EMISSION CONTROLS.''.
(iv) State the date you finished installation (month and year).
(3) Make sure the original and supplemental labels are readily
visible after the engine is installed in the vehicle or, if the vehicle
obscures the engine's emission control information label, make sure the
vehicle manufacturer attaches duplicate labels, as described in Sec.
1068.105 of this chapter.
(4) Send the Designated Officer a signed letter by the end of each
calendar year (or less often if we tell you) with all the following
information:
(i) Identify your full corporate name, address, and telephone
number.
(ii) List the models you expect to produce under this exemption in
the coming year.
(iii) State: ``We produce each listed model for recreational
application without making any changes that could increase its
certified emission levels, as described in 40 CFR 1051.605.''.
(e) If we request it, you must send us emission test data on the
applicable recreational duty cycle(s). You may include the data in your
application for certification under 40 CFR part 86 or part 1048, or in
your letter requesting the exemption. We will generally not ask you for
these data under normal circumstances, especially when they are more
readily available from another source.
Sec. 1051.610 What are the provisions for producing recreational
vehicles with engines already certified under the motor-vehicle program
or the Large SI program?
(a) You may produce a recreational vehicle without certifying it
under this part by using a certified motor vehicle engine, or Large SI
engine. This section does not apply if you manufacture the engine
yourself; see Sec. 1051.605. In order to produce recreational vehicles
under this section, you must meet all of the following criteria:
(1) The engine or vehicle is certified to 40 CFR part 86 or part
1048.
(2) The engine is not adjusted outside the certifying
manufacturer's specifications (see Sec. 1051.605(c)(2)).
(3) The engine or vehicle is not modified in any way that may
affect its emission control. This does not apply to refueling emission
controls.
(4) The vehicle is labeled consistent with paragraph (c) of this
section.
(b)(1) The only requirements or prohibitions from this part that
apply to a vehicle that is exempt under this section are in this
section and Sec. 1051.605.
(2) If the vehicles do not meet the criteria listed in Sec.
1051.605(c) and paragraph (c) of this section, they will be subject to
the standards and prohibitions of this part. Producing these vehicles
without a valid exemption or certificate of conformity would violate
the prohibitions in Sec. 1068.101 of this chapter.
(3) Vehicles exempted under this section are subject to all the
requirements affecting engines and vehicles under 40 CFR part 86 or
part 1048, as applicable. The requirements and restrictions of 40 CFR
part 86 or 1048 apply to anyone manufacturing these engines, anyone
manufacturing vehicles that use these engines, and all other persons in
the same manner as if these engines were used in a motor vehicle or
other nonrecreational application.
(c)(1) Make sure the original emission control information label is
intact after assembly in the vehicle.
(2) Add a permanent supplemental label to the vehicle in a position
where it will be clearly visible. In this emission control information
label, do the following:
(i) Include the heading: ``Recreational Vehicle Emission Control
Information''.
(ii) Include your full corporate name and trademark.
[[Page 68402]]
(iii) State: ``THIS ENGINE WAS ADAPTED FOR RECREATIONAL USE WITHOUT
AFFECTING ITS EMISSION CONTROLS.''.
(iv) State the date you finished installation (month and year).
(3) Send the Designated Officer a signed letter by the end of each
calendar year (or less often if we tell you) with all the following
information:
(i) Identify your full corporate name, address, and telephone
number.
(ii) List the models you expect to produce under this exemption in
the coming year.
(iii) State: ``We produce each listed model for recreational
application without making any changes that could increase its
certified emission levels, as described in 40 CFR 1051.605.''.
(d) If you build recreational vehicles under this section, we may
require (as a condition of the exemption) that you comply with the
emission-related warranty and recall responsibilities of this part.
(e) If you build a recreational vehicle using a motor vehicle
engine that was certified as part of a vehicle-based engine family, we
may require you to certify under this part instead of granting you an
exemption under this part. If we do this, we may allow you to submit an
abbreviated application for certification to show that you comply with
the requirements of this part. You may reference the information in the
original motor vehicle application.
Sec. 1051.615 What are the special provisions for certifying small
recreational engines?
(a) You may certify ATVs with engines that have total displacement
of less than 100 cc to the following emission exhaust standards instead
of certifying them to the exhaust emission standards of subpart B of
this part:
(1) 25.0 g/kW-hr HC+NOX, with an FEL cap of 40.0 g/kW-hr
HC+NOX.
(2) 500 g/kW-hr CO.
(b) You may certify off-highway motorcycles with engines that have
total displacement of 70 cc or less to the following emission exhaust
standards instead of certifying them to the exhaust emission standards
of subpart B of this part:
(1) 16.1 g/kW-hr HC+NOX, with an FEL cap of 32.2 g/kW-hr
HC+NOX.
(2) 519 g/kW-hr CO.
(c) You may use the averaging, banking, and trading provisions of
subpart H of this part to show compliance with this HC+NOX
standards (an engine family meets emission standards even if its family
emission limit is higher than the standard, as long as you show that
the whole averaging set of applicable engine families meet the
applicable emission standards using emission credits, and the vehicles
within the family meet the family emission limit). You may not use
averaging to meet the CO standards of this section.
(d) Measure emissions by testing the engine on a dynamometer with
the steady-state duty cycle described in Table 1 of this section.
(1) During idle mode, hold the speed within your specifications,
keep the throttle fully closed, and keep engine torque under 5 percent
of the peak torque value at maximum test speed.
(2) For the full-load operating mode, operate the engine at wide-
open throttle.
(3) See part 1065 of this chapter for detailed specifications of
tolerances and calculations.
(4) Table 1 follows:
Table 1 of Sec. 1051.615.--6-Mode Duty Cycle for Recreational Engines
----------------------------------------------------------------------------------------------------------------
Torque
Engine speed (percent of Minimum time
(percent of maximum test in mode Weighting
maximum test torque at test (minutes) factors
speed) speed)
----------------------------------------------------------------------------------------------------------------
Mode number:
1........................................... 85 100 5.0 0.09
-------------------------------------------------
2........................................... 85 75 5.0 0.20
-------------------------------------------------
3........................................... 85 50 5.0 0.29
-------------------------------------------------
4........................................... 85 25 5.0 0.30
-------------------------------------------------
5........................................... 85 10 5.0 0.07
-------------------------------------------------
6........................................... Idle 0 5.0 0.05
----------------------------------------------------------------------------------------------------------------
(e) All other requirements and prohibitions of this part apply to
these engines and vehicles.
Sec. 1051.620 When may a manufacturer obtain an exemption for
competition recreational vehicles?
(a) We may grant you an exemption from the standards and
requirements of this part for a new recreational vehicle on the grounds
that it is to be used solely for competition. The provisions of this
part other than those in this section do not apply to recreational
vehicles that we exempt for use solely for competition.
(b) We will exempt vehicles that we determine will be used solely
for competition. The basis of our determinations are described in
paragraphs (b)(1), (b)(2), and (c) of this section. Exemptions granted
under this section are good for only one model year and you must
request renewal for each subsequent model year. We will not approve
your renewal request if we determine the vehicles will not be used
solely for competition.
(1) Off-highway motorcycles. Motorcycles that are marketed and
labeled as only for competitive use and that meet at least four of the
criteria listed in paragraphs (b)(1)(i) through (vi) of this section
are considered to be used solely for competition, except in cases where
other information is available that indicates that they are not used
solely for competition. The following features are indicative of
motorcycles used solely for competition:
(i) The absence of a headlight or other lights.
(ii) The absence of a spark arrestor.
(iii) The absence of manufacturer warranty.
(iv) Suspension travel greater than 10 inches.
(v) Engine displacement greater than 50 cc.
(vi) The absence of a functional seat. (For example, a seat less
with than 30 square inches of seating surface would
[[Page 68403]]
generally not be considered a functional seat).
(2) Snowmobiles and ATVs. Snowmobiles and ATVs meeting all of the
following criteria are considered to be used solely for competition,
except in cases where other information is available that indicates
that they are not used solely for competition:
(i) The vehicle or engine may not be displayed for sale in any
public dealership.
(ii) Sale of the vehicle must be limited to professional racers or
other qualified racers.
(iii) The vehicle must have performance characteristics that are
substantially superior to noncompetitive models.
(c) Vehicles not meeting the applicable criteria listed in
paragraph (b) of this section will be exempted only in cases where the
manufacturer has clear and convincing evidence that the vehicles will
be used solely for competition.
(d) You must permanently label vehicles exempted under this section
to clearly indicate that they are to be used only for competition.
Failure to properly label a vehicle will void the exemption for that
vehicle.
(e) If we request it, you must provide us any information we need
to determine whether the vehicles are used solely for competition.
Sec. 1051.625 What special provisions apply to unique snowmobile
designs for small-volume manufacturers?
(a) If you are a small-volume manufacturer, we may permit you to
produce up to 600 snowmobiles per year that are certified to less
stringent emission standards than those in Sec. 1051.103, as long as
you meet all the conditions and requirements in this section.
(b) To apply for alternate standards under this section, send the
Designated Officer a written request. In your request, do two things:
(1) Show that the snowmobile has unique design, calibration, or
operating characteristics that make it atypical and infeasible or
highly impractical to meet the emission standards in Sec. 1051.103,
considering technology, cost, and other factors.
(2) Identify the level of compliance you can achieve, including a
description of available emission-control technologies and any
constraints that may prevent more effective use of these technologies.
(c) You must give us other relevant information if we ask for it.
(d) An authorized representative of your company must sign the
request and include the statement: ``All the information in this
request is true and accurate, to the best of my knowledge.''.
(e) Send your request for this extension at least nine months
before the relevant deadline. If different deadlines apply to companies
that are not small-volume manufacturers, do not send your request
before the regulations in question apply to the other manufacturers.
(f) If we approve your request, we will set alternate standards for
your qualifying snowmobiles. These standards will not be above 400 g/
kW-hr for CO or 150 g/kW-hr for HC.
(g) You may produce these snowmobiles to meet the alternate
standards we establish under this section as long as you continue to
produce them at the same or lower emission levels.
(h) You may not include snowmobiles you produce under this section
in any averaging, banking, or trading calculations under Subpart H of
this part.
(i) You must meet all the requirements of this part, except as
noted in this section.
Sec. 1051.630 What special provisions apply to unique snowmobile
designs for all manufacturers?
(a) We may permit you to produce up to 600 snowmobiles per year
that are certified to the FELs listed in this section without new test
data, as long as you meet all the conditions and requirements in this
section.
(b) You may certify these snowmobiles with FELs of 560 g/kW-hr for
CO and 270 g/kW-hr for HC (using the normal certification procedures).
(c) The emission levels described in this section are intended to
represent worst-case emission levels. You may not certify snowmobiles
under this section if good engineering judgment indicates that they
have emission rates higher than these levels.
(d) Include snowmobiles you produce under this section in your
averaging calculations under Subpart H of this part.
(e) You must meet all the requirements of this part, unless the
regulations of this part specify otherwise.
Sec. 1051.635 What provisions apply to new manufacturers that are
small businesses?
(a) If you are a small business (as defined by the Small Business
Administration) that manufactures recreational vehicles, but does not
otherwise qualify for the small-volume manufacturer provisions of this
part, you may ask us to designate you to be a small-volume
manufacturer. You may do this whether you began manufacturing
recreational vehicles before, during, or after 2002.
(b) We may set other reasonable conditions that are consistent with
the intent of this section and the Act. For example, we may place sales
limits on companies that we designate to be small-volume manufacturers
under this section.
Subpart H--Averaging, Banking, and Trading for Certification
Sec. 1051.701 General provisions.
(a) You may average, bank, and trade emission credits for purposes
of certification as described in this subpart to show compliance with
the standards of this part. To do this you must show that your average
emission levels are below the applicable standards in subpart B of this
part, or that you have sufficient credits to offset a credit deficit
for the model year (as calculated in Sec. 1051.720). If you cannot
show in your end-of-year report that your average emission levels are
below the applicable standards in subpart B of this part, or that you
have sufficient credits to offset a credit deficit for the model year,
we may void the certificates for all families certified to FELs above
the allowable average. (b) The following averaging set restrictions
apply:
(1) You may not average together engine families that are certified
to different standards. You may, however, use banked credits that were
generated relative to different standards, except as prohibited by
paragraphs (b)(2) and (3) of this section, paragraph (e) of this
section, or by other provisions in this part. For example, you may not
average together within a model year off-highway motorcycles that are
certified to the standards in Sec. 1051.105(a)(1) and Sec.
1051.105(a)(2); but you may use banked credits generated by off-highway
motorcycles that are certified to the standards in Sec. 1051.105(a)(1)
to show compliance with the standards in Sec. 1051.105(a)(2) in a
later model year, and vice versa.
(2) There are separate averaging, banking, and trading programs for
snowmobiles, ATVs, and off-highway motorcycles. You may not average or
exchange banked or traded credits from engine families of one type of
vehicle with those from engine families of another type of vehicle.
(3) You may not average or exchange banked or traded credits with
other engine families if you use fundamentally different measurement
procedures for the different engine families (for example, ATVs
certified to
[[Page 68404]]
chassis-based vs. engine-based standards). This paragraph (b)(3) does
not restrict you from averaging together engine families that use test
procedures that we determine provide equivalent emission results.
(4) You may not average or exchange banked or traded exhaust
credits with evaporative credits, or vice versa.
(c) The definitions of Subpart I of this part apply to this
subpart. The following definitions also apply:
(1) Average standard means a standard that allows you comply by
averaging all your vehicles under this part. See subpart B of this part
to determine which standards are average standards.
(2) Broker means any entity that facilitates a trade between a
buyer and seller.
(3) Buyer means the entity that receives credits as a result of
trade.
(4) Family emission limit (FEL) has the meaning given in it in
Sec. 1051.801.
(5) Reserved credits means credits you have generated that we have
not yet verified in reviewing the end-of-year report.
(6) Seller means the entity that provides credits during a trade.
(d) Do not include any exported vehicles in the certification
averaging, banking, and trading program. Include only vehicles
certified under this part.
Sec. 1051.705 How do I average emission levels?
(a) As specified in subpart B of this part, certify each vehicle to
a family emission limit (FEL).
(b) Calculate a preliminary average emission level according to
Sec. 1051.720 using projected U.S.-directed production volumes for
your application for certification.
(c) After the end of your model year, calculate a final average
emission level according to Sec. 1051.720 for each type of
recreational vehicle or engine you manufacture or import. Use actual
U.S.-directed production volumes.
(d) If your preliminary average emission level is below the
allowable average standard, see Sec. 1051.710 for information about
generating and banking emission credits. These credits will be
considered reserved until we verify them in reviewing the end-of-year
report.
Sec. 1051.710 How do I generate and bank emission credits?
(a) If your average emission level is below the average standard,
you may calculate credits according to Sec. 1051.720.
(b) You may generate credits if you are a certifying manufacturer.
(c) You may bank unused emission credits, but only after the end of
the calendar year and after we have reviewed your end-of-year reports.
Credits you generate do not expire.
(d) During the calendar year and before you send in your end-of-
year report, you may consider reserved any credits you originally
designate for banking during certification. You may redesignate these
credits for trading in your end-of-year report, but they are not valid
to demonstrate compliance until verified.
(e) You may use for averaging or trading any credits you declared
for banking from the previous calendar year that we have not reviewed.
But, we may revoke these credits later--following our review of your
end-of-year report or audit actions. For example, this could occur if
we find that credits are based on erroneous calculations; or that
emission levels are misrepresented, unsubstantiated, or derived
incorrectly in the certification process.
Sec. 1051.715 How do I trade emission credits?
(a) You may trade only banked emission credits, not reserved
credits.
(b) You may trade banked credits to any certifying manufacturer.
(c) If a negative credit balance results from a credit trade, both
buyers and sellers are liable, except in cases involving fraud. We may
void the certificates of all emission families participating in a
negative trade.
(1) If you buy credits but have not caused the negative credit
balance, you must only supply more credits equivalent to the amount of
invalid credits you used.
(2) If you caused the credit shortfall, you may be subject to the
requirement sof Sec. 1051.730(b)(6).
Sec. 1051.720 How do I calculate my average emission level or
emission credits?
(a) Calculate your average emission level for each type of
recreational vehicle or engine for each model year according to the
following equation and round it to the nearest tenth of a g/km or g/kW-
hr. Use consistent units throughout the calculation.
(1) For exhaust emissions:
(i) Calculate the average emission level as:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.011
Where:
FELi = The FEL to which the engine family is certified.
ULi = The useful life of the engine family.
Productioni = The number of vehicles in the engine family.
(ii) Use U.S.-directed production projections for initial
certification, and actual U.S.-directed production volumes to determine
compliance at the end of the model year.
(2) For vehicles that have standards expressed as g/kW-hr and a
useful life in km, convert the useful life to kW-hr based on the
maximum power output observed over the emission test and an assumed
vehicle speed of 30 km/hr as follows: UL (kW-hr) = UL (km) x Maximum
Test Power (kW)/30 km/hr. (Note: It is not necessary to include a load
factor, since credit exchange is not allowed between vehicles certified
to g/kW-hr standards and vehicles certified to g/km standards.)
(3) For evaporative permeation standards expressed as g/
m2/day, use the useful life value in years multiplied by
365.24, and calculate the average emission level as:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.012
[[Page 68405]]
Where:
Productioni = The number of vehicles in the engine family
times the average internal surface area of the vehicles' fuel tanks.
(b) If your average emission level is below the average standard,
calculate credits available for banking according to the following
equation and round them to the nearest tenth of a gram:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.013
(c) If your average emission level is above the average standard,
calculate your preliminary credit deficit according to the following
equation, rounding to the nearest tenth of a gram:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.014
Sec. 1051.725 What information must I keep?
(a) Maintain and keep five types of properly organized and indexed
records for each engine family:
(1) Model year and EPA engine family.
(2) FEL.
(3) Useful life.
(4) Projected U.S.-directed production volume for the model year.
(5) Actual U.S.-directed production volume for the model year.
(b) Keep paper records of this information for three years from the
due date for the end-of-year report. You may use any additional storage
formats or media if you like.
(c) Keep a copy of all of the information you send us under Sec.
1051.730.
(d) We may ask you to keep or send other information necessary to
implement this subpart.
Sec. 1051.730 What information must I report?
(a) Include the following information in each of your applications
for certification:
(1) A statement that, to the best of your belief, you will not have
a negative credit balance for any type of recreational vehicle or
engine when all credits are calculated. This means that if you believe
that your average emission level will be above the standard (i.e., that
you will have a deficit for the model year), you must have banked
credits (or project to have received traded credits) to offset the
deficit.
(2) Detailed calculations of projected emission credits (zero,
positive, or negative) based on U.S.-directed production projections.
If you project a credit deficit, state the source of credits needed to
offset the credit deficit.
(b) At the end of each model year, send an end-of-year report.
(1) Your report must include three things:
(i) Calculate in detail your average emission level and any
emission credits (positive, or negative) based on actual U.S.-directed
production volumes.
(ii) If your average emission level is above the allowable average
standard, demonstrate that you have the credits needed to offset the
credit deficit. If you cannot demonstrate that you have the credits at
the time you submit your end-of-year report, we may void the
certificates for all families certified to FELs above the allowable
average.
(iii) If your average emission level is below the allowable average
standard, state whether you will reserve the credits for banking.
(2) Base your U.S.-directed production volumes on the point of
first retail sale. You may consider distributors to be the point of
first retail sale if all their engines are sold to ultimate buyers in
the United States.
(3) Send end-of-year reports to the Designated Officer within 120
days of the end of the model year. If you send reports later, you are
violating the Act.
(4) If you generate credits for banking and you do not send your
end-of-year reports within 120 days after the end of the model year,
you may not use or trade the credits until we receive and review your
reports. You may not use projected credits pending our review.
(5) You may correct errors discovered in your end-of-year report,
including errors in calculating credits according to the following
table:
----------------------------------------------------------------------------------------------------------------
If-- And if-- Then we--
----------------------------------------------------------------------------------------------------------------
(i) Our review discovers an error in the discovery occurs within restore the credits for your use.
your end-of-year report that 180 days of receipt.
increases your credit balance.
--------------------------------------
(ii) You discover an error in your the discovery occurs within restore the credits for your use.
report that increases your credit 180 days of receipt.
balance.
--------------------------------------
(iii) We or you discover and error in the discovery occurs more do not restore the credits for your use.
your report that increases your than 180 days after receipt.
credit balance.
--------------------------------------
(iv) We discover an error in your at any time after receipt.... reduce your credit balance
report that reduces your credit
balance.
----------------------------------------------------------------------------------------------------------------
(6) If our review of a your end-of year-report shows a negative
balance, you may buy credits to bring your credit balance to zero. But
you must buy 1.1 credits for each 1.0 credit needed. If enough credits
are not available to bring
[[Page 68406]]
your credit balance to zero within 90 days of when we notify you, we
may void the certificates for all families certified to FELs above the
allowable average.
(c) Within 90 days of any credit trade, you must send the
Designated Officer a report of the trade that includes three types of
information:
(1) The corporate names of the buyer, seller, and any brokers.
(2) Copies of contracts related to credit trading from the buyer,
seller, and broker, as applicable.
(d) Include in each report a statement certifying the accuracy and
authenticity of its contents.
(e) We may void a certificate of conformity for any emission family
if you do not keep the records this section requires or give us the
information when we ask for it.
Sec. 1051.735 Are there special averaging provisions for snowmobiles?
For snowmobiles, you may only use credits for the same phase or set
of standards against which they were generated, except as allowed by
this section.
(a) Restrictions. (1) You may not use any Phase 1 or Phase 2
credits for Phase 3 compliance.
(2) You may not use Phase 1 HC credits for Phase 2 HC compliance.
However, because the Phase 1 and Phase 2 CO standards are the same, you
may use Phase 1 CO credits for compliance with the Phase 2 CO
standards.
(b) Special credits for next phase of standards. You may choose to
generate credits early for banking for purposes of compliance with
later phases of standards as follows:
(1) If your corporate average emission level at the end of the
model year exceeds the applicable (current) phase of standards (without
the use of traded or previously banked credits), you may choose to
redesignate some of your snowmobile production to a calculation to
generate credits for a future phase of standards. To generate credits
the snowmobiles designated must have an FEL below the emission level of
that set of standards. This can be done on a pollutant specific basis.
(2) Do not include the snowmobiles that you redesignate in the
final compliance calculation of your average emission level for the
otherwise applicable (current) phase of standards. Your average
emission level for the remaining (non-redesignated) snowmobiles must
comply with the otherwise applicable (current) phase of standards.
(3) Include the snowmobiles that you redesignate in a separate
calculation of your average emission level for redesignated engines.
Calculate credits using this average emission level relative to the
specific pollutant in the future phase of standards. These credits may
be used for compliance with the future standards.
(4) For generating early Phase 3 credits, you may generate credits
for HC+NOX or CO separately as described:
(i) To determine if you qualify to generate credits in accordance
with paragraphs (b)(1) through (3) of this section, you must meet the
credit trigger level. For HC+NOX this value is 62 g/kW-hr
(which would be the HC+NOX standard that would result from
inputting the highest allowable CO standard (275 g/kW-hr) into the
Phase 3 equation). For CO the value is 200 g/kW-hr (which would be the
CO standard that would result from inputting the highest allowable
HC+NOX standard (90 g/kW-hr) into the Phase 3 equation).
(ii) HC+NOX and CO credits for Phase 3 are calculated
relative to the 62 g/kW-hr and 200 g/kW-hr values, respectively.
(5) Credits can also be calculated for Phase 3 using both sets of
standards. Without regard to the trigger level values, if your net
emission reduction for the redesignated averaging set exceeds the
requirements of Phase 3 in Sec. 1051.103 (using both HC+NOX
and CO in the Phase 3 equation in Sec. 1051.103), then your credits
are the difference between the Phase 3 reduction requirement of that
section and your calculated value.
Subpart I--Definitions and Other Reference Information
Sec. 1051.801 What definitions apply to this part?
The following definitions apply to this part. The definitions apply
to all subparts unless we note otherwise. All undefined terms have the
meaning the Act gives to them. The definitions follow:
Act means the Clean Air Act, as amended, 42 U.S.C. 7401 et seq.
Adjustable parameter means any device, system, or element of design
that someone can adjust (including those which are difficult to access)
and that, if adjusted, may affect emissions or engine performance
during emission testing or normal in-use operation. You may ask us to
exclude a parameter that is difficult to access if it cannot be
adjusted to affect emissions without significantly degrading
performance, or if you otherwise show us that it will not be adjusted
in use in a way that affect emissions
Aftertreatment means relating to any system, component, or
technology mounted downstream of the exhaust valve or exhaust port
whose design function is to reduce exhaust emissions.
All-terrain vehicle means a land-based or amphibious nonroad
vehicle that meets the criteria listed in paragraph (1) of this
definition; or, alternatively, the criteria of paragraph (2) of this
definition but not the criteria of paragraph (3) of this definition.
(1) Vehicles designed to travel on four low pressure tires, having
a seat designed to be straddled by the operator and handlebars for
steering controls, and intended for use by a single operator and no
other passengers are all-terrain vehicles.
(2) Other all-terrain vehicles have three or more wheels and one or
more seats, are designed for operation over rough terrain, and are
intended primarily for transportation. Golf carts generally do not meet
these criteria since they are generally not designed for operation over
rough terrain.
(3) Vehicles that meet the definition of ``offroad utility
vehicle'' in this section are not all-terrain vehicles. However, Sec.
1051.1(a) specifies that some offroad utility vehicles are required to
meet the same requirements as all-terrain vehicles.
Auxiliary emission-control device means any element of design that
senses temperature, engine rpm, motive speed, transmission gear,
atmospheric pressure, manifold pressure or vacuum, or any other
parameter to activate, modulate, delay, or deactivate the operation of
any part of the emission-control system. This also includes any other
feature that causes in-use emissions to be higher than those measured
under test conditions, except as we allow under this part. For example,
an accelerator pump would be considered an auxiliary emission-control
device.
Brake power means the usable power output of the engine not
including power required to operate fuel pumps, oil pumps, or coolant
pumps.
Broker means any entity that facilitates a trade of emission
credits between a buyer and seller.
Calibration means the set of specifications and tolerances specific
to a particular design, version, or application of a component or
assembly capable of functionally describing its operation over its
working range.
Certification means obtaining a certificate of conformity for an
engine family that complies with the emission standards and
requirements in this part.
Compression-ignition means relating to a type of reciprocating,
internal-combustion engine that is not a spark-ignition engine.
[[Page 68407]]
Crankcase emissions means airborne substances emitted to the
atmosphere from any part of the engine crankcase's ventilation or
lubrication systems. The crankcase is the housing for the crankshaft
and other related internal parts.
Designated Officer means the Manager, Engine Programs Group (6405-
J), U.S. Environmental Protection Agency, 1200 Pennsylvania Ave.,
Washington, DC 20460.
Emission-control system means any device, system, or element of
design that controls or reduces the regulated emissions from a vehicle.
Emission-data vehicle means a vehicle or engine that is tested for
certification.
Emission-related maintenance means maintenance that substantially
affects emissions or is likely to substantially affect emissions
deterioration.
Engine family means a group of vehicles with similar emission
characteristics, as specified in Sec. 1051.230.
Evaporative means relating to fuel emissions that result from
permeation of fuel through the fuel system materials and from
ventilation of the fuel system.
Family emission limit (FEL) means an emission level declared by the
manufacturer to serve in place of an emission standard for
certification under the emission-credit program in subpart H of this
part. The family emission limit must be expressed to the same number of
decimal places as the emission standard it replaces.
Fuel system means all components involved in transporting,
metering, and mixing the fuel from the fuel tank to the combustion
chamber(s), including the fuel tank, fuel tank cap, fuel pump, fuel
filters, fuel lines, carburetor or fuel-injection components, and all
fuel-system vents.
Good engineering judgment has the meaning we give it in Sec.
1068.5 of this chapter.
Hydrocarbon (HC) means the hydrocarbon group on which the emission
standards are based for each fuel type. For gasoline- and LPG-fueled
engines, HC means total hydrocarbon (THC). For natural gas-fueled
engines, HC means nonmethane hydrocarbon (NMHC). For alcohol-fueled
engines, HC means total hydrocarbon equivalent (THCE).
Identification number means a unique specification (for example,
model number/serial number combination) that allows someone to
distinguish a particular vehicle or engine from other similar vehicle
or engines.
Manufacturer has the meaning given in section 216(1) of the Act. In
general, this term includes any person who manufactures a vehicle or
engine for sale in the United States or otherwise introduces a new
vehicle or engine into commerce in the United States. This includes
importers that import for resale.
Maximum brake power means the maximum brake power of an engine at
test conditions.
Maximum test power means the maximum brake power of an engine at
maximum test speed.
Maximum test speed has the meaning we give in Sec. 1065.515 of
this chapter
Maximum test torque means the torque output observed at wide-open
throttle at a given speed.
Model year means one of the following things:
(1) For freshly manufactured vehicles or engines (see definition of
``new,'' paragraph (1)), model year means one of the following:
(i) Calendar year.
(ii) Your annual new model production period if it is different
than the calendar year. This must include January 1 of the calendar
year for which the model year is named. It may not begin before January
2 of the previous calendar year and it must end by December 31 of the
named calendar year.
(2) For a vehicle or engine that is converted to a nonroad vehicle
or engine after being placed into service in a motor vehicle, model
year means the calendar year in which the vehicle or engine was
originally produced (see definition of ``new,'' paragraph (2)).
(3) For a nonroad vehicle excluded under Sec. 1051.5 that is later
converted to operate in an application that is not excluded, model year
means the calendar year in which the vehicle was originally produced
(see definition of ``new,'' paragraph (3)).
(4) For engines that are not freshly manufactured but are installed
in new nonroad vehicles, model year means the calendar year in which
the engine is installed in the new nonroad vehicle. This installation
date is based on the time that final assembly of the vehicle is
complete (see definition of ``new,'' paragraph (4)).
(5) For a vehicle or engine modified by an importer (not the
original manufacturer) who has a certificate of conformity for the
imported vehicle or engine (see definition of ``new,'' paragraph (5)),
model year means one of the following:
(i) The calendar year in which the importer finishes modifying and
labeling the vehicle or engine.
(ii) Your annual production period for producing vehicles or
engines if it is different than the calendar year; follow the
guidelines in paragraph (1)(ii) of this definition.
(6) For a vehicle or engine you import that does not meet the
criteria in paragraphs (1) through (5) of the definition of ``new''
model year means the calendar year in which the manufacturer completed
the original assembly of the vehicle or engine. In general, this
applies to used equipment that you import without conversion or major
modification.
Motor vehicle has the meaning we give in Sec. 85.1703(a) of this
chapter. In general, motor vehicle means a self-propelled vehicle that
can transport one or more people or any material, but does not include
any of the following:
(1) Vehicles having a maximum ground speed over level, paved
surfaces no higher than 40 km per hour (25 miles per hour).
(2) Vehicles that lack features usually needed for safe, practical
use on streets or highways-for example, safety features required by
law, a reverse gear (except for motorcycles), or a differential.
(3) Vehicles whose operation on streets or highways would be
unsafe, impractical, or highly unlikely. Examples are vehicles with
tracks instead of wheels, very large size, or features associated with
military vehicles, such as armor or weaponry.
New means relating to any of the following vehicles or engines:
(1) A freshly manufactured engine or vehicle for which the ultimate
buyer has never received the equitable or legal title. This kind of
vehicle might commonly be thought of as ``brand new.'' In the case of
this paragraph (1), the vehicle or engine is no longer new when the
ultimate buyer receives this title or the product is placed into
service, whichever comes first.
(2) An engine originally manufactured as a motor vehicle engine
that is later intended to be used in a piece of nonroad equipment. In
this case, the engine ceases being a motor vehicle engine and becomes a
``new nonroad engine''. The engine is no longer new when it is placed
into nonroad service.
(3) A nonroad engine that has been previously placed into service
in an application we exclude under Sec. 1051.5 or exempt under
1051.620, where that engine is installed in a piece of equipment for
which these exclusions or exemptions do not apply. The engine is no
longer new when it is placed into nonroad service. For example, this
would apply to a competition vehicle that is no longer used solely for
competition.
(4) An engine not covered by paragraphs (1) through (3) of this
[[Page 68408]]
definition that is intended to be installed in new nonroad equipment.
The engine is no longer new when the ultimate buyer receives a title
for the equipment or the product is placed into service, whichever
comes first. This generally includes installation of used engines in
new vehicles.
(5) An imported nonroad vehicle or engine covered by a certificate
of conformity issued under this part, where someone other than the
original manufacturer modifies the vehicle or engine after its initial
assembly and holds the certificate. The vehicle or engine is no longer
new when it is placed into nonroad service.
(6) An imported nonroad vehicle or engine that is not covered by a
certificate of conformity issued under this part at the time of
importation. This addresses uncertified engines and vehicles that have
been placed into service in other countries and that someone seeks to
import into the United States. Importation of this kind of new nonroad
engine or vehicle is generally prohibited by part 1068 of this chapter.
Noncompliant vehicle or engine means a vehicle or engine that was
originally covered by a certificate of conformity, but is not in the
certified configuration or otherwise does not comply with the
conditions of the certificate.
Nonconforming vehicle or engine means a vehicle or engine not
covered by a certificate of conformity that would otherwise be subject
to emission standards.
Nonmethane hydrocarbon means the difference between the emitted
mass of total hydrocarbons and the emitted mass of methane.
Nonroad means relating to nonroad engines, or to vehicles or
equipment that include nonroad engines.
Nonroad engine has the meaning given in Sec. 1068.30 of this
chapter. In general this means all internal-combustion engines except
motor vehicle engines, stationary engines, or engines used solely for
competition. This part only applies to nonroad engines that are used in
snowmobiles, off-highway motorcycles, and ATVs (see Sec. 1051.5).
Off-highway motorcycle means a two-wheeled vehicle with a nonroad
engine and a seat (excluding marine vessels and aircraft). (Note:
highway motorcycles are regulated under 40 CFR part 86.)
Offroad utility vehicle means a nonroad vehicle that has four or
more wheels, seating for two or more persons, is designed for operation
over rough terrain, and has either a rear payload 350 pounds or more or
seating for six or more passengers. Vehicles intended primarily for
recreational purposes that are not capable of transporting six
passengers (such as dune buggies) are not offroad utility vehicles.
(Note: Sec. 1051.1(a) specifies that some offroad utility vehicles are
required to meet the requirements that apply for all-terrain vehicles.)
Oxides of nitrogen has the meaning given it in 40 CFR part 1065.
Phase 1 means relating to Phase 1 standards of Sec. Sec. 1051.103,
1051.105, or 1051.107, or other Phase 1 standards specified in subpart
B of this part.
Phase 2 means relating to Phase 2 standards of Sec. 1051.103, or
other Phase 2 standards specified in subpart B of this part.
Phase 3 means relating to Phase 3 standards of Sec. 1051.103, or
other Phase 3 standards specified in subpart B of this part.
Physically adjustable range means the entire range over which an
engine parameter can be adjusted, except as modified by Sec.
1051.115(c). For parts described in Sec. 1051.115(d), ``physically
adjustable range'' means the adjustable range defined in that
paragraph.
Placed into service means used for its intended purpose.
Point of first retail sale means the location at which the retail
sale occurs. This generally means a dealership.
Recreational means, for purposes of this part, relating to
snowmobiles, all-terrain vehicles, off-highway motorcycles, and other
vehicles that we regulate under this part. Note that 40 CFR part 90
applies to other recreational vehicles.
Revoke means to discontinue the certificate for an engine family.
If we revoke a certificate, you must apply for a new certificate before
continuing to produce the affected vehicles or engines. This does not
apply to vehicles or engines you no longer possess.
Round means to round numbers according to ASTM E29-02 (incorporated
by reference in Sec. 1051.810), unless otherwise specified.
Scheduled maintenance means adjusting, repairing, removing,
disassembling, cleaning, or replacing components or systems that is
periodically needed to keep a part from failing or malfunctioning. It
also may mean actions you expect are necessary to correct an overt
indication of failure or malfunction for which periodic maintenance is
not appropriate.
Small-volume manufacturer means:
(1) For motorcycles and ATVs, a manufacturer that sold motorcycles
or ATVs before 2003 and had annual U.S.-directed production of no more
than 5,000 off-road motorcycles and ATVs (combined number) in 2002 and
all earlier calendar years. For manufacturers owned by a parent
company, the limit applies to the production of the parent company and
all of its subsidiaries.
(2) For snowmobiles, a manufacturer that sold snowmobiles before
2003 and had annual U.S.-directed production of no more than 300
snowmobiles in 2002 and all earlier model years. For manufacturers
owned by a parent company, the limit applies to the production of the
parent company and all of its subsidiaries.
(3) A manufacturer that we designate to be a small-volume
manufacturer under Sec. 1051.635.
Snowmobile means a vehicle designed to operate outdoors only over
snow-covered ground, with a maximum width of 1.5 meters or less.
Spark-ignition means relating to a gasoline-fueled engine, or any
other engine with a spark plug (or other sparking device) and with
operating characteristics significantly similar to the theoretical Otto
combustion cycle. Spark-ignition engines usually use a throttle to
regulate intake air flow to control power during normal operation.
Suspend means to temporarily discontinue the certificate for an
engine family. If we suspend a certificate, you may not sell vehicles
or engines from that engine family unless we reinstate the certificate
or approve a new one.
Test sample means the collection of vehicles or engines selected
from the population of an engine family for emission testing.
Test vehicle or engine means a vehicle or engine in a test sample.
Total hydrocarbon means the combined mass organic compounds
measured by our total hydrocarbon test procedure, expressed as a
hydrocarbon with a hydrogen-to-carbon mass ratio of 1.85:1.
Total hydrocarbon equivalent means the sum of the carbon mass
contributions of non-oxygenated hydrocarbons, alcohols and aldehydes,
or other organic compounds that are measured separately as contained in
a gas sample, expressed as petroleum-fueled engine hydrocarbons. The
hydrogen-to-carbon ratio of the equivalent hydrocarbon is 1.85:1.
Ultimate buyer means ultimate purchaser.
Ultimate purchaser means, with respect to any new vehicle or
engine, the first person who in good faith purchases such vehicle or
engine for purposes other than resale.
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the
[[Page 68409]]
Commonwealth of the Northern Mariana Islands, Guam, American Samoa, the
U.S. Virgin Islands, and the Trust Territory of the Pacific Islands.
Upcoming model year means for an engine family the model year after
the one currently in production.
U.S.-directed production means the number of vehicle units, subject
to the requirements of this part, produced by a manufacturer (and/or
imported) for which the manufacturer has a reasonable assurance that
sale was or will be made to ultimate buyers in the United States.
Useful life means the period during which a vehicle is required to
comply with all applicable emission standards, specified as a number of
kilometers, hours, and/or calendar years. It must be at least as long
as both of the following:
(1) The expected average service life before the vehicle is
remanufactured or retired from service.
(2) The minimum useful life value.
Void means to invalidate a certificate or an exemption. If we void
a certificate, all the vehicles produced under that engine family for
that model year are considered noncompliant, and you are liable for
each vehicle produced under the certificate and may face civil or
criminal penalties or both. If we void an exemption, all the vehicles
produced under that exemption are considered uncertified (or
nonconforming), and you are liable for each vehicle produced under the
exemption and may face civil or criminal penalties or both. You may not
produce any additional vehicles using the voided exemption.
Wide-open throttle means maximum throttle opening. Unless this is
specified at a given speed, it refers to maximum throttle opening at
maximum speed. For electronically controlled or other engines with
multiple possible fueling rates, wide-open throttle also means the
maximum fueling rate at maximum throttle opening under test conditions.
Sec. 1051.805 What symbols, acronyms, and abbreviations does this
part use?
The following symbols, acronyms, and abbreviations apply to this
part:
[deg]--degrees.
ASTM--American Society for Testing and Materials.
ATV--all-terrain vehicle.
cc--cubic centimeters.
cm--centimeter.
C--Celsius.
CO--carbon monoxide.
CO2--carbon dioxide.
EPA--Environmental Protection Agency.
F--Fahrenheit.
g--grams.
g/gal/day--grams per gallon per test day.
g/m2/day--grams per meter-square per test day.
Hg--mercury.
hr--hours.
km--kilometer.
kW--kilowatt.
LPG--liquefied petroleum gas.
m--meters.
mm--millimeters.
mW--milliwatts.
NMHC--nonmethane hydrocarbons.
NOX--oxides of nitrogen (NO and NOX).
psig--pounds per square inches of gauge pressure.
rpm--revolutions per minute.
SAE--Society of Automotive Engineers.
SI--spark-ignition.
THC--total hydrocarbon.
THCE--total hydrocarbon equivalent.
U.S.C.--United States Code.
Sec. 1051.810 What materials does this part reference?
We have incorporated by reference the documents listed in this
section. The Director of the Federal Register approved the
incorporation by reference as prescribed in 5 U.S.C. 552(a) and 1 CFR
part 51. Anyone may inspect copies at the U.S. EPA, Air and Radiation
Docket and Information Center, 1301 Constitution Ave., NW., Room B102,
EPA West Building, Washington, DC 20460 or the Office of the Federal
Register, 800 N. Capitol St., NW., 7th Floor, Suite 700, Washington,
DC.
(a) ASTM material. Table 1 of Sec. 1051.810 lists material from
the American Society for Testing and Materials that we have
incorporated by reference. The first column lists the number and name
of the material. The second column lists the sections of this part
where we reference it. Anyone may purchase copies of these materials
from the American Society for Testing and Materials, 100 Barr Harbor
Dr., West Conshohocken, PA 19428. Table 1 follows:
Table 1 of Sec. 1051.810.--ASTM Materials
------------------------------------------------------------------------
Part 1051
Document number and name reference
------------------------------------------------------------------------
ASTM D471-98, Standard Test Method for Rubber Property- 1051.501
Effect of Liquids..........................................
-------------------------------------------------------------
ASTM D814-95 (reapproved 2000), Standard Test Method for 1051.245
Rubber Property-Vapor Transmission of Volatile Liquids.....
-------------------------------------------------------------
ASTM E29-02, Standard Practice for Using Significant Digits 1051.801
in Test Data to Determine Conformance with Specifications..
------------------------------------------------------------------------
(b) SAE material. Table 2 of Sec. 1051.810 lists material from the
Society of Automotive Engineering that we have incorporated by
reference. The first column lists the number and name of the material.
The second column lists the sections of this part where we reference
it. Anyone may purchase copies of these materials from the Society of
Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.
Table 2 follows:
Table 2 of Sec. 1051.810.--SAE Materials
------------------------------------------------------------------------
Part 1051
Document number and name reference
------------------------------------------------------------------------
SAE J30, Fuel and Oil Hoses, June 1998...................... 1051.245,
1051.501
-------------------------------------------------------------
SAE J1930, Electrical/Electronic Systems Diagnostic Terms, 1051.135
Definitions, Abbreviations, and Acronyms, May 1998.........
-------------------------------------------------------------
SAE J2260, Nonmetallic Fuel System Tubing with One or More 1051.245
Layers, November 1996......................................
------------------------------------------------------------------------
Sec. 1051.815 How should I request EPA to keep my information
confidential?
(a) Clearly show what you consider confidential by marking,
circling, bracketing, stamping, or some other method. We will store
your confidential information as described in 40 CFR part 2. Also, we
will disclose it only as specified in 40 CFR part 2.
(b) If you send us a second copy without the confidential
information, we will assume it contains nothing confidential whenever
we need to release information from it.
(c) If you send us information without claiming it is confidential,
we may make it available to the public without further notice to you,
as described in Sec. 2.204 of this chapter.
Sec. 1051.820 How do I request a hearing?
See 40 CFR part 1068, subpart G, for information related to
hearings.
PART 1065--TEST PROCEDURES AND EQUIPMENT
Subpart A--Applicability and General Provisions
Sec.
1065.1 Applicability.
1065.5 Overview of test procedures.
1065.10 Other test procedures.
1065.15 Engine testing.
1065.20 Limits for test conditions.
Subpart B--Equipment and Analyzers
1065.101 Overview.
1065.105 Dynamometer and engine equipment specifications.
1065.110 Exhaust gas sampling system; spark-ignition (SI) engines.
[[Page 68410]]
1065.115 Exhaust gas sampling system; compression-ignition engines.
[Reserved]
1065.120 Raw sampling. [Reserved]
1065.125 Analyzers (overview/general response characteristics).
1065.130 Hydrocarbon analyzers.
1065.135 NOX analyzers.
1065.140 CO and CO2 analyzers.
1065.145 Smoke meters. [Reserved]
1065.150 Flow meters.
1065.155 Temperature and pressure sensors.
Subpart C--Test Fuels and Analytical Gases
1065.201 General requirements for test fuels.
1065.205 Test fuel specifications for distillate diesel fuel.
[Reserved]
1065.210 Test fuel specifications for gasoline.
1065.215 Test fuel specifications for natural gas.
1065.220 Test fuel specifications for liquefied petroleum gas.
1065.240 Lubricating oils.
1065.250 Analytical gases.
Subpart D--Analyzer and Equipment Calibrations
1065.301 Overview.
1065.305 International calibration standards.
1065.310 CVS calibration. [Reserved]
1065.315 Torque calibration.
Subpart E--Engine Selection, Preparation, and Service Accumulation
1065.401 Selecting a test engine.
1065.405 Preparing and servicing a test engine.
1065.410 Service limits for stabilized test engines.
1065.415 Durability demonstration.
Subpart F--Running an Emission Test
1065.501 Overview of the engine dynamometer test procedures.
1065.510 Engine mapping procedures.
1065.515 Test cycle generation.
1065.520 Engine starting, restarting, and shutdown.
1065.525 Engine dynamometer test run.
1065.530 Test cycle validation criteria.
Subpart G--Data Analysis and Calculations
1065.601 Overview.
1065.605 Required records.
1065.610 Bag sample analysis.
1065.615 Bag sample calculations.
Subpart H--Particulate Measurements [Reserved]
Subpart I--Testing With Oxygenated Fuels
1065.801 Applicability.
1065.805 Sampling system.
1065.810 Calculations.
Subpart J--Field Testing
1065.901 Applicability.
1065.905 General provisions.
1065.910 Measurement accuracy and precision.
1065.915 Equipment specifications for SI engines.
1065.920 Equipment setup and test run for SI engines.
1065.925 Calculations.
1065.930 Specifications for mass air flow sensors.
1065.935 Specifications for THC analyzers.
1065.940 Specifications for NOX and air/fuel sensors.
1065.945 Specifications for CO analyzers.
1065.950 Specifications for speed and torque measurement.
Subpart K--Definitions and Other Reference Information
1065.1001 Definitions.
1065.1005 Symbols, acronyms, and abbreviations.
1065.1010 Reference materials.
1065.1015 Confidential information.
Authority: 42 U.S.C. 7401-7671(q).
Subpart A--Applicability and General Provisions
Sec. 1065.1 Applicability.
(a) This part describes the procedures that apply to testing that
we require for the following engines or for equipment using the
following engines:
(1) Large nonroad spark-ignition engines we regulate under 40 CFR
part 1048.
(2) Vehicles that we regulate under 40 CFR part 1051 (i.e.,
recreational SI vehicles) that are regulated based on engine testing.
See 40 CFR part 1051 to determine which vehicles may be certified based
on engine test data.
(b) This part does not apply to any of the following engine or
vehicle categories:
(1) Light-duty highway vehicles (see 40 CFR part 86).
(2) Heavy-duty highway Otto-cycle engines (see 40 CFR part 86).
(3) Heavy-duty highway diesel engines (see 40 CFR part 86).
(4) Aircraft engines (see 40 CFR part 87).
(5) Locomotive engines (see 40 CFR part 92).
(6) Land-based nonroad diesel engines (see 40 CFR part 89).
(7) General marine engines (see 40 CFR parts 89 and 94).
(8) Marine outboard and personal watercraft engines (see 40 CFR
part 91).
(9) Small nonroad spark-ignition engines (see 40 CFR part 90).
(c) This part is addressed to you as a manufacturer, but it applies
equally to anyone who does testing for you, and to us when we conduct
testing to determine if you meet emission standards.
(d) Paragraph (a) of this section identifies the parts of the CFR
that define emission standards and other requirements for particular
types of engines. In this part 1065, we refer to each of these other
parts generically as the ``standard-setting part.'' For example, 40 CFR
part 1051 is always the standard-setting part for snowmobiles. Follow
the standard-setting part if it differs from this part.
(e) For equipment subject to this part and regulated under
equipment-based or vehicle-based standards, interpret the term
``engine'' in this part to include equipment and vehicles(see 40 CFR
1068.30).
Sec. 1065.5 Overview of test procedures.
(a) Some of the provisions of this part do not apply to all types
of engines. For example, measurement of particulate matter is generally
not required for spark-ignition engines. See the standard-setting part
to determine which provisions in this part may not apply. Before using
this part's procedures, read the standard-setting part to answer at
least the following questions:
(1) How should I warm up the test engine before measuring
emissions? Do I need to measure cold-start emissions during this warm-
up segment of the duty cycle?
(2) Do I measure emissions while the warmed-up engine operates over
a steady-state schedule, a transient schedule, or both?
(3) What are the speed and load points of the test cycle(s)?
(4) Which exhaust constituents do I need to measure?
(5) Does testing require full-flow dilute sampling? Is raw sampling
acceptable? Is partial-flow dilute sampling acceptable?
(6) Do any unique specifications apply for test fuels?
(7) What maintenance steps may I do before or between tests on an
emission-data engine?
(8) Do any unique requirements apply to stabilizing emission levels
on a new engine?
(9) Do any unique requirements apply to testing conditions, such as
ambient temperatures or pressures?
(10) Are there special emission standards that affect engine
operation and ambient conditions?
(11) Are there different emission standards that apply to field
testing under normal operation?
(b) The following table shows how this part divides testing
specifications into subparts:
------------------------------------------------------------------------
Describes these specifications or
This subpart... procedures...
------------------------------------------------------------------------
Subpart A........................... General provisions for test
procedures.
-------------------------------------
Subpart B........................... Equipment for testing.
-------------------------------------
Subpart C........................... Fuels and analytical gases for
testing.
[[Page 68411]]
-------------------------------------
Subpart D........................... How to calibrate test equipment.
-------------------------------------
Subpart E........................... How to prepare engines for
testing, including service
accumulation.
-------------------------------------
Subpart F........................... How to test for emissions.
-------------------------------------
Subpart G........................... How to calculate emission levels
from measured data.
-------------------------------------
Subpart H........................... [Reserved].
-------------------------------------
Subpart I........................... How to measure emissions from
engines fueled with an oxygenated
fuel such as methanol or ethanol.
-------------------------------------
Subpart J........................... How to do field testing of in-use
vehicles and equipment.
-------------------------------------
Subpart K........................... Definitions, abbreviations, and
other reference information that
apply to emission testing.
------------------------------------------------------------------------
Sec. 1065.10 Other test procedures.
(a) Your testing. These test procedures apply for all testing that
you do to show compliance with emission standards, with a few
exceptions listed in this section.
(b) Our testing. These test procedures generally apply for testing
that we do to determine if your engines comply with applicable emission
standards. We may conduct other testing as allowed by the Act.
(c) Exceptions. You may be allowed or required to use test
procedures other than those specified in this part in the following
cases:
(1) The test procedures in this part are intended to produce
emission measurements equivalent to those that would result from
measuring emissions during in-use operation using the same engine
configuration installed in a piece of equipment. If good engineering
judgment indicates that use of the procedures in this part for an
engine would result in measurements that are not representative of in-
use operation of that engine, you must notify us. If we determine that
using these procedures would result in measurements that are
significantly unrepresentative and that changing the procedures will
result in more representative measurements and not decrease the
stringency of emission standards, we will specify changes to the
procedures. In your notification to us, you should recommend specific
changes you think are necessary.
(2) You may ask to use emission data collected using other test
procedures, such as those of the California Air Resources Board or the
International Organization for Standardization. We will allow this only
if you show us that these data are equivalent to data collected using
our test procedures.
(3) You may ask to use alternate procedures that produce
measurements equivalent to those from the specified procedures. If you
send us a written request showing your procedures are equivalent, and
we agree that they are equivalent, we will allow you to use them. You
may not use an alternate procedure until we approve them, either by:
telling you directly that you may use this procedure; or issuing
guidance to all manufacturers, which allows you to use the alternate
procedure without additional approval.
(4) You may ask to use special test procedures if your engine
cannot be tested under the specified procedures (for example, your
engine cannot operate on the specified transient cycle). In this case,
tell us in writing why you cannot satisfactorily test your engines
using this part's procedures and ask to use a different approach. We
will approve your special test procedures if we determine they would
produce emission measurements that are representative of those that
would result from measuring emissions during in-use operation. You may
not use special procedures until we approve them.
(5) The standard-setting part may contain other specifications for
test procedures that apply for your engines. In cases where it is not
possible to comply with both the test procedures in those parts and the
test procedures in this part, you must comply with the test procedures
specified in the standard-setting part. Those other parts may also
allow you to deviate from the test procedures of this part for other
reasons.
Sec. 1065.15 Engine testing.
(a) This part describes the procedures for performing exhaust
emission tests on engines that must meet emission standards.
(b) Generally, you must test an engine while operating it on a
laboratory dynamometer over a prescribed sequence. (Subpart J of this
part describes in-use testing of engines installed in vehicles or
equipment.) You need to sample and analyze the exhaust gases generated
during engine operation to determine the concentration of the regulated
pollutants.
(c) Concentrations are converted into units of grams of pollutant
per kilowatt-hour (g/kW-hr) or similar units for comparison to emission
standards. If the applicable emission standards are expressed as g/bhp-
hr, references in this part to kW should generally be interpreted to
mean horsepower.
Sec. 1065.20 Limits for test conditions.
(a) Unless specified elsewhere in this chapter, you may conduct
tests to determine compliance with duty-cycle emission standards at
ambient temperatures of 20-30[deg]
C (68-86[deg]
F), ambient pressures
of 600-775 mm Hg, and any ambient humidity level.
(b) Follow the standard-setting part for ambient conditions when
testing to determine compliance with not-to-exceed or other off-cycle
emission standards.
(c) For engine testing in a laboratory, you may heat, cool, and/or
dehumidify the dilution air before it enters the CVS.
(d) For engine testing in a laboratory, if the barometric pressure
observed while generating the maximum-torque curve changes by more than
25 mm Hg from the value measured when you started mapping, you must
remap the engine. Also, to have a valid test, the average barometric
pressure observed during the exhaust emission test must be within 25 mm
Hg of the average observed during the maximum torque curve generation
(see Sec. 1065.510).
Subpart B--Equipment and Analyzers
Sec. 1065.101 Overview.
This subpart describes equipment and analyzers for measuring
emissions. Subpart D of this part describes how to calibrate these
devices and subpart C of this part defines the accuracy and purity
specifications of analytical gases.
Sec. 1065.105 Dynamometer and engine equipment specifications.
(a) The engine dynamometer system must be able to control engine
torque and speed simultaneously over the applicable test cycles within
the accuracies specified in Sec. 1065.530. If your dynamometer cannot
meet the accuracy requirements in Sec. 1065.530, you must get our
approval before using it. For transient testing, issue command set
points for engine torque and speed at 5 Hz or greater (10 Hz
recommended). Record feedback engine torque and speed at least once
every second during the test. In addition to these general
requirements, make sure your engine or dynamometer's readout signals
for speed and torque meet the following accuracies for all testing:
(1) Engine speed readout must be accurate to within +/-2 percent of
the absolute standard value. A 60-tooth (or greater) wheel in
combination with a common mode rejection frequency counter is
considered an absolute standard for engine or dynamometer speed.
[[Page 68412]]
(2) Engine flywheel torque readout must meet one of the two
following standards for accuracy:
(i) Within +/-3 percent of the NIST true value torque (as defined
in Sec. 1065.315).
(ii) The following accuracies:
------------------------------------------------------------------------
Engine flywheel torque
If the full-scale torque value is... readout must be within...
------------------------------------------------------------------------
T <= 550 ft-lbs........................... +/-2.5 ft-lbs. of NIST true
value.
-------------------------------------------
550 < T <= 1050 ft-lbs.................... +/-5.0 ft-lbs. of NIST true
value.
-------------------------------------------
T £ 1050 ft-lbs. +/-10.0 ft-lbs. of NIST true
value.
------------------------------------------------------------------------
(3) Option: You may use internal dynamometer signals (such as
armature current) to measure torque if you can show that the engine
flywheel torque during the test cycle conforms to paragraph (b)(2) of
this section. Your measurements must compensate for increased or
decreased flywheel torque because of the armature's inertia during
accelerations and decelerations in the test cycle.
(b) To verify that the test engine has followed the test cycle
correctly, collect the dynamometer or engine readout signals for speed
and torque so you can statistically correlate the engine's actual
performance with the test cycle (see Sec. 1065.530). Normally, to do
this, you would convert analog signals from the dynamometer or engine
into digital values for computer storage, but all conversions must meet
two criteria:
(1) Speed values used to evaluate cycles must be accurate to within
2 percent of the readout value for dynamometer or engine speed.
(2) Engine flywheel torque values used to evaluate cycles must be
accurate to within 2 percent of the readout value for dynamometer or
engine flywheel torque.
(c) You may combine the tolerances in paragraphs (a) and (b) of
this section if you use the root mean square (RMS) method and refer
accuracies of the RMS values to absolute-standard or NIST true values.
(1) Speed values used to evaluate cycles must be accurate to within
+/-2.8 percent of the absolute standard values, as defined in paragraph
(a)(1) of this section.
(2) Engine flywheel torque values used to evaluate cycles must be
accurate to within +/-3.6 percent of NIST true values, as determined in
Sec. 1065.315.
Sec. 1065.110 Exhaust gas sampling system; spark-ignition (SI)
engines.
(a) General. The exhaust gas sampling system described in this
section is designed to measure the true mass of gaseous emissions in
the exhaust of SI engines. (If the standard-setting part requires
determination of THCE or NMHCE for your engine, then see subpart I of
this part for additional requirements.) Under the constant-volume
sampler (CVS) concept, you must measure the total volume of the mixture
of exhaust and dilution air and collect a continuously proportioned
volume of sample for analysis. You must control flow rates so that the
ratio of sample flow to CVS flow remains constant. You then determine
the mass emissions from the sample concentration and total flow over
the test period.
(1) Do not let the CVS or dilution air inlet system artificially
lower exhaust system backpressure. To verify proper backpressures,
measure pressure in the raw exhaust immediately upstream of the inlet
to the CVS. Continuously measure and compare the static pressure of the
raw exhaust observed during a transient cycle--with and without the CVS
operating. Static pressure measured with the CVS system operating must
remain within +/-5 inches of water (1.2 kPa) of the static pressure
measured when disconnected from the CVS, at identical moments in the
test cycle. (Note: We will use sampling systems that can maintain the
static pressure to within +/-1 inch of water (0.25 kPa) if your written
request shows that this closer tolerance is necessary.) This
requirement serves as a design specification for the CVS/dilution air
inlet system, and should be performed as often as good engineering
practice dictates (for example, after installing an uncharacterized
CVS, adding an unknown inlet restriction on the dilution air, or
otherwise altering the system).
(2) The system for measuring temperature (sensors and readout) must
have an accuracy and precision of +/-3.4[deg]
F (+/-1.9[deg]
C). The
temperature measuring system for a CVS without a heat exchanger must
respond within 1.50 seconds to 62.5 percent of a temperature change (as
measured in hot silicone oil). For a CVS with a heat exchanger, there
is no specific requirement for response time.
(3) The system for measuring pressure (sensors and readout) must
have an accuracy and precision of +/-3 mm Hg (0.4 kPa).
(4) The flow capacity of the CVS must be large enough to keep water
from condensing in the system. You may dehumidify the dilution air
before it enters the CVS. You also may heat or cool the air if three
conditions exist:
(i) The air (or air plus exhaust gas) temperature does not exceed
250[deg]
F (121[deg]
C).
(ii) You calculate the CVS flow rate necessary to prevent water
condensation based on the lowest temperature in the CVS before
sampling. (We recommend insulating the CVS system when you use heated
dilution air.)
(iii) The dilution ratio is high enough to prevent condensation in
bag samples as they cool to room temperature.
(5) Bags for collecting dilution air and exhaust samples must be
big enough for samples to flow freely.
(6) The general CVS sample system consists of a dilution air filter
(optional) and mixing assembly, cyclone particulate separator
(optional), a sample line for the bag sample or other sample lines a
dilution tunnel, and associated valves and sensors for pressure and
temperature. Except for the system to sample hydrocarbons from two-
stroke engines, the temperature of the sample lines must be more than
3[deg]
C above the mixture's maximum dew point and less than 121[deg]
C. We recommend maintaining them at 113 +/- 8[deg]
C. For the
hydrocarbon sampling system with two-stroke engines, the temperature of
the sample lines should be maintained at 191 +/- 11[deg]
C. A general
schematic of the SI sampling system is shown in Figure 1065.110-1,
which follows:
BILLING CODE 6560-50-P
[[Page 68413]]
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.017
BILLING CODE 6460-50-C
(b) Steady-state testing. Constant proportional sampling is
required throughout transient testing, but is not required throughout
steady-state testing.
[[Page 68414]]
Steady-state testing requires that you draw a proportional sample for
each test mode, but you may sample in different proportions for
different test modes, as long as you know the ratio of the sample flow
to total flow during each test mode. This allowance means that you may
use simpler flow control systems for steady-state testing than are
shown in Figure 1065.110-1 of this section.
(c) Configuration variations. Since various configurations can
produce equivalent results, you need not conform exactly to the
drawings in this subpart. You may use other components--such as
instruments, valves, solenoids, pumps and switches--to provide more
information and coordinate the components' functions. Based on good
engineering judgment, you may exclude other components that are not
needed to maintain accuracy on some systems.
(d) CFV-CVS component description. The flow characteristics of a
Critical-Flow Venturi, Constant-Volume Sampler (CFV-CVS) are governed
by the principles of fluid dynamics associated with critical flow. The
CFV system is commonly called a constant-volume system (CVS) even
though the mass flow varies. More properly, they are constant-
proportion sampling systems, because small CFVs in each of the sample
lines maintains proportional sampling while temperatures vary. This CFV
maintains the mixture's flow rate at choked flow, which is inversely
proportional to the square root of the gas temperature, and the system
computes the actual flow rate continuously. Because pressures and
temperatures are the same at all venturi inlets, the sample volume is
proportional to the total volume. The CFV-CVS sample system uses
critical flow venturis for the bag sample or other sample lines (these
are shown in the figure as flow control valves) and a critical flow
venturi for the dilution tunnel. All venturis must be maintained at the
same temperature.
(e) EFC-CVS component description. The electronic flow control-CVS
(EFC-CVS) system for sampling is identical to the CFV system described
in paragraph (b) of this section, except that it adds electronic flow
controllers (instead of sampling venturis), a subsonic venturi and an
electronic flow controller for the CVS (instead of the critical flow
venturi), metering valves, and separate flow meters (optional) to
totalize sample flow volumes. The EFC sample system must conform to the
following requirements:
(1) The system must meet all the requirements in paragraph (b) of
this section.
(2) The ratio of sample flow to CVS flow must not vary by more than
+/-5 percent from the test's setpoint.
(3) Sample flow totalizers must meet the accuracy specifications in
Sec. 1065.150. You may obtain total volumes from the flow controllers,
with our advance approval, if you can show they meet these accuracies.
(f) Component description, PDP-CVS. The positive-displacement pump-
CVS (PDP-CVS) system for sampling is identical to the CFV system
described in paragraph (b) of this section, except for the following
changes:
(1) Include a heat exchanger.
(2) Use positive-displacement pumps for the CVS flow and sampling-
system flow. You do not need sampling venturis or a venturi for the
dilution tunnel. All pumps must operate at a constant flow rate.
(3) All pumps must operate at a nominally constant temperature.
Maintain the gas mixture's temperature--measured at a point just ahead
of the positive-displacement pump (and after the heat exchanger for the
main CVS pump)--within +/-10[deg]
F (+/-5.6[deg]
C) of the average
operating temperature observed during the test. (You may estimate the
average operating temperature from the temperatures observed during
similar tests.) The system for measuring temperature (sensors and
readout) must have an accuracy and precision of +/-3.4[deg]
F (1.9[deg]
C), and response time consistent with good engineering judgment.
(g) Mixed systems. You may combine elements of paragraphs (d), (e),
and (f) consistent with good engineering judgment. For example, you may
control the CVS flow rate using a CFV, and control sample flow rates
using electronic flow controllers.
Sec. 1065.115 Exhaust gas sampling system; compression-ignition
engines. [Reserved]
Sec. 1065.120 Raw sampling. [Reserved]
Sec. 1065.125 Analyzers (overview/general response characteristics).
(a) General. The following sections and subparts describe the
specifications for analyzers and analytical equipment:
(1) The analyzers for measuring hydrocarbon, NOX, CO,
and CO2 emission concentrations are specified in Sec.
1065.130 through Sec. 1065.140.
(2) The analytical equipment for measuring particulate emissions is
specified in Subpart H of this part.
(3) The analytical equipment for measuring emissions of oxygenated
compounds (for example, methanol) is specified in Subpart I of this
part.
(4) The analytical equipment for measuring in-use emissions is
specified in Subpart J of this part.
(b) Response time. Analyzers must have the following response
characteristics:
(1) For steady-state testing and transient testing with bag sample
analysis, the analyzer must reach at least 90 percent of its final
response within 5.0 seconds after any step change to the input
concentration at or above 80 percent of full scale.
(2) For transient testing with continuous measurement, the analyzer
must reach at least 90 percent of its final response within 1.0 second
after any step change to the input concentration at or above 80 percent
of full scale.
(c) Precision and noise. Analyzers must meet the following
characteristics for precision and noise:
(1) Precision must be no worse than +/-1 percent of full-scale
concentration for each range used above 155 ppm (or ppmC), or +/-2
percent for each range used below 155 ppm (or ppmC). For this paragraph
(c)(1), we define precision as 2.5 times the standard deviation of 10
repetitive responses to a given calibration or span gas.
(2) Peak-to-peak response to zero and calibration or span gases
over any 10-second period must be no more than 2 percent of full-scale
chart deflection on all ranges used.
(d) Drift. Analyzers must meet specifications for zero-response and
span drift.
(1) The zero-response drift during one hour must be less than 2
percent of full-scale chart deflection on the lowest range used. Zero-
response is the mean response, including noise, to a zero-gas during a
30-second interval.
(2) The span drift during one hour must be less than 2 percent of
full-scale chart deflection on the lowest range used. Span is the
difference between the span-response and the zero-response. Span-
response is the mean response, including noise, to a span gas during a
30-second interval.
(e) Calibration. See subpart D of this part for specifications to
calibrate analyzers.
Sec. 1065.130 Hydrocarbon analyzers.
This section describes the requirements for flame ionization
detectors (FIDs) used to measure hydrocarbons.
(a) Fuel the FID with a mixture of hydrogen in helium and calibrate
it using propane.
(b) If you use a heated FID (required only for diesels and two-
stroke, spark-ignition engines), keep the temperature 191 +/-11[deg]
C).
[[Page 68415]]
(c) Use an overflow sampling system for heated continuous FIDs. (In
an overflow system excess zero gas or span gas spills out of the probe
when you are doing zero or span checks.)
(d) Do not premix the FID fuel and burner air.
(e) Make sure the FID meets accuracy and precision specifications
in ISO 8178-1 (incorporated by reference in Sec. 1065.1010).
Sec. 1065.135 NOX analyzers.
This section describes the requirements for chemiluminescent
detectors (CLD) used to measure NOX. Good engineering
practice may require the use of other detectors.
(a) A CLD must meet the following requirements:
(1) Make sure your CLD meets the accuracy and precision
specifications in ISO 8178-1 (incorporated by reference in Sec.
1065.1010).
(2) The NO to NO2 converter must have an efficiency of
at least 90 percent.
(3) Use an overflow sampling system for continuous CLDs. (In an
overflow system excess zero gas or span gas spills out of the probe
when you are doing zero or span checks.)
(4) You do not need a heated CLD to test spark-ignition engines.
(b) Using CLDs is generally acceptable even though they measure
only NO and NO2, since conventional engines do not emit
significant amounts of other NOX species.
Sec. 1065.140 CO and CO2 analyzers.
This section describes the requirements for non-dispersive infrared
absorption detectors (NDIR) to measure CO and CO2.
(a) The NDIR must meet the applicable accuracy and precision
specifications of ISO 8178-1 (incorporated by reference in Sec.
1065.1010).
(b) The NDIR must meet the applicable quench and interference
requirements of ISO 8178-1 (incorporated by reference in Sec.
1065.1010).
Sec. 1065.145 Smoke meters. [Reserved]
Sec. 1065.150 Flow meters.
(a) Flow meters must have accuracy and precision of +/-2 percent of
point or better and be traceable to NIST standards.
(b) You may correct flow measurements for temperature or pressure,
if your temperature and pressure measurements have accuracy and
precision of +/-2 percent of point or better (absolute).
Sec. 1065.155 Temperature and pressure sensors.
(a) Except where we specify otherwise in this part, must meet the
applicable accuracy and precision specifications of ISO 8178-1
(incorporated by reference in Sec. 1065.1010).
(b) Use good engineering judgment to design and operate your
temperature and pressure measuring systems to minimize delays in
response time and avoid hysteresis.
Subpart C--Test Fuels and Analytical Gases
Sec. 1065.201 General requirements for test fuels.
(a) For all emission tests, use test fuels meeting the
specifications in this subpart, unless the standard-setting part
directs otherwise. For any service accumulation on a test engine, if we
do not specify a fuel, use the specified test fuel or a fuel typical of
what you would expect the engine to use in service.
(b) We may require you to test the engine with each type of fuel it
can use (for example, gasoline and natural gas).
(c) If you will produce engines that can run on a type of fuel (or
mixture of fuels) that we do not specify in this subpart, we will allow
you to test with fuel representing commercially available fuels of that
type. However, we must approve your fuel's specifications before you
may use it for emission testing.
(d) You may use a test fuel other than those we specify in this
subpart if you do all of the following:
(1) Show that it is commercially available.
(2) Show that your engines will use only the designated fuel in
service.
(3) Show that operating the engines on the fuel we specify would
increase emissions or decrease durability.
(4) Get our written approval before you start testing.
(e) We may allow you to use other test fuels (for example,
California Phase 2 gasoline) if they do not affect the demonstration of
compliance.
Sec. 1065.205 Test fuel specifications for distillate diesel fuel.
[Reserved]
Sec. 1065.210 Test fuel specifications for gasoline.
Gasoline used as a test fuel must meet the following
specifications:
(a) Unless the standard-setting part requires testing with fuel
appropriate for low temperatures, use gasoline test fuels meeting the
specifications in the following table:
Table 1 of Sec. 1065.210.--General Test-Fuel Specifications for Gasoline
----------------------------------------------------------------------------------------------------------------
Item Procedure \1\ Value \1\
----------------------------------------------------------------------------------------------------------------
Distillation Range:
1. Initial boiling point, [deg]C.... ASTM D 86-01 23.9-35.0\2\
-----------------------------------------
2. 10% point, [deg]C................ ASTM D 86-01 48.9-57.2
-----------------------------------------
3.50% point, [deg]C................. ASTM D 86-01 93.3-110.0
-----------------------------------------
4. 90% point, [deg]C................ ASTM D 86-01 148.9-162.8
-----------------------------------------
5. End point, [deg]C (maximum)...... ASTM D 86-01 212.8.
-----------------------------------------
Hydrocarbon composition:
1. Olefins, volume %................ ASTM D 1319-02 10 maximum
-----------------------------------------
2. Aromatics, volume %.............. ASTM D 1319-02 35 maximum
-----------------------------------------
3. Saturates........................ ASTM D 1319-02 Remainder
-----------------------------------------
Lead (organic), g/liter................. ASTM D 3237-97 0.013 maximum
-----------------------------------------
Phosphorous, g/liter.................... ASTM D 3231-02 0.0013 maximum
[[Page 68416]]
-----------------------------------------
Sulfur, weight %........................ ASTM D 1266-98 0.008 maximum
-----------------------------------------
Volatility (Reid Vapor Pressure), kPa... ASTM D 323-99a 60.0 to 63.4.\2,3\
----------------------------------------------------------------------------------------------------------------
\1\All ASTM standards are incorporated by reference in Sec. 1065.1010.
\2\For testing at altitudes above 1 219 m, the specified volatility range is 52 to 55 kPa (7.5 to 8.0) and the
specified initial boiling point range is 23.9[deg]
to 40.6[deg]
C.
\3\For testing unrelated to evaporative emissions, the specified range is 55 to 63 kPa (8.0 to 9.1 psi).
(b) If the standard-setting part requires testing with fuel
appropriate for low temperatures, use gasoline test fuels meeting the
specifications in the following table:
Table 2 of Sec. 1065.210.--Low-Temperature Test-Fuel Specifications for Gasoline
----------------------------------------------------------------------------------------------------------------
Item Procedure \1\ Value \1\
----------------------------------------------------------------------------------------------------------------
Distillation Range:
1. Initial boiling point, [deg]C.... ASTM D 86-01 24.4-35.6.
-----------------------------------------
2. 10% point, [deg]C................ ASTM D 86-01 36.7-47.8.
-----------------------------------------
3. 50% point, [deg]C................ ASTM D 86-01 81.7-101.1.
-----------------------------------------
4. 90% point, [deg]C................ ASTM D 86-01 157.8-174.4.
-----------------------------------------
5. End point, [deg]C (maximum)...... ASTM D 86-01 211.7.
-----------------------------------------
Hydrocarbon composition:
1. Olefins, volume %................ ASTM D 1319-02 17.5 maximum.
-----------------------------------------
2. Aromatics, volume %.............. ASTM D 1319-02 30.4 maximum.
-----------------------------------------
3. Saturates........................ ASTM D 1319-02 Remainder.
-----------------------------------------
Lead (organic), g/liter................. ASTM D 3237-97 0.013 maximum.
-----------------------------------------
Phosphorous, g/liter.................... ASTM D 3231-02 0.005 maximum.
-----------------------------------------
Sulfur, weight %........................ ASTM D 1266-98 0.08 maximum.
-----------------------------------------
Volatility (Reid Vapor Pressure), kPa... ASTM D 323-99a 11.2--11.8 psi.
----------------------------------------------------------------------------------------------------------------
\1\All ASTM standards are incorporated by reference in Sec. 1065.1010.
(c) Use gasoline test fuel with octane values that represent
commercially available fuels for the appropriate application.
Sec. 1065.215 Test fuel specifications for natural gas.
(a) Natural gas used as a test fuel must meet the specifications in
the following table:
Table 1 of Sec. 1065.215.--Test-Fuel Specifications for Natural Gas
----------------------------------------------------------------------------------------------------------------
Item Procedure\1\ Value (mole percent)
----------------------------------------------------------------------------------------------------------------
1. Methane.............................. ASTM D 1945-96 87.0 minimum.
2. Ethane............................... ASTM D 1945-96 5.5 maximum.
3. Propane.............................. ASTM D 1945-96 1.2 maximum.
4. Butane............................... ASTM D 1945-96 0.35 maximum.
5. Pentane.............................. ASTM D 1945-96 0.13 maximum.
6. C6 and higher........................ ASTM D 1945-96 0.1 maximum.
7. Oxygen............................... ASTM D 1945-96 1.0 maximum.
8. Inert gases (sum of CO2 and N2)...... ASTM D 1945-96 5.1 maximum.
----------------------------------------------------------------------------------------------------------------
\1\All ASTM standards are incorporated by reference in Sec. 1065.1010.
(b) At ambient conditions, the fuel must have a distinctive odor
detectable down to a concentration in air of not more than one-fifth of
the lower flammability limit.
[[Page 68417]]
Sec. 1065.220 Test fuel specifications for liquefied petroleum gas.
(a) Liquefied petroleum gas used as a test fuel must meet the
specifications in the following table:
Table 1 of Sec. 1065.220.--Test-Fuel Specifications for Liquefied Petroleum Gas
----------------------------------------------------------------------------------------------------------------
Item Procedure \1\ Value
----------------------------------------------------------------------------------------------------------------
1. Propane........................ ASTM D 2163-91 85.0 vol. percent minimum.
-----------------------------------
2. Vapor pressure at 38[deg]
C.... ASTM D 1267-02 or 2598-02 14 bar maximum.
\2\
-----------------------------------
3. Volatility residue (evaporated ASTM D 1837-02 -38[deg]
C maximum.
temp., 35[deg]
C).
-----------------------------------
4. Butanes........................ ASTM D 2163-91 5.0 vol. percent maximum.
-----------------------------------
5. Butenes........................ ASTM D 2163-91 2.0 vol. percent maximum.
-----------------------------------
6. Pentenes and heavier........... ASTM D 2163-91 0.5 vol. percent maximum.
-----------------------------------
7. Propene........................ ASTM D 2163-91 10.0 vol. percent maximum.
-----------------------------------
8. Residual matter (residue on ASTM D 2158-02 0.05 ml maximum pass.\3\
evap. of 100 ml oil stain
observ.).
-----------------------------------
9. Corrosion, copper strip........ ASTM D 1838-91 No. 1 maximum.
-----------------------------------
10. Sulfur........................ ASTM D 2784-98 80 ppm maximum.
-----------------------------------
11. Moisture content.............. ASTM D 2713-91 pass.
----------------------------------------------------------------------------------------------------------------
\1\ All ASTM standards are incorporated by reference in Sec. 1065.1010.
\2\ If these two test methods yield different results, use the results from ASTM D 1267-02.
\3\ The test fuel must not yield a persistent oil ring when you add 0.3 ml of solvent residue mixture to a
filter paper in 0.1 ml increments and examine it in daylight after two minutes (see ASTM D 2158-02).
(b) At ambient conditions, the fuel must have a distinctive odor
detectable down to a concentration in air of not over one-fifth of the
lower flammability limit.
Sec. 1065.240 Lubricating oils.
Lubricating oils you use to comply with this part must be
commercially available and represent the oil that will be used with
your in-use engines.
Sec. 1065.250 Analytical gases.
Analytical gases that you use to comply with this part must meet
the accuracy and purity specifications of this section. You must record
the expiration date specified by the gas supplier and may not use any
gas after the expiration date.
(a) Pure gases. Use the ``pure gases'' shown in the following
table:
Table 1 of Sec. 1065.250.--Concentration Limits for Pure Gases
--------------------------------------------------------------------------------------------------------------------------------------------------------
Maximum contaminant concentrations
Gas type ------------------------------------------------------------------------------------------- Oxygen content
Organic carbon Carbon monoxide Carbon dioxide Nitric oxide (NO)
--------------------------------------------------------------------------------------------------------------------------------------------------------
Purified Nitrogen................. 1 ppmC............... 1 ppm................ 400 ppm.............. 0.1 ppm............. NA.
-----------------------------------
Purified Oxygen................... NA................... NA................... NA................... NA.................. 99.5-100.0%.
-----------------------------------
Purified Synthetic Air, or Zero- 1 ppmC............... 1 ppm................ 400 ppm.............. 0.1 ppm............. 18-21%.
Grade Air.
--------------------------------------------------------------------------------------------------------------------------------------------------------
(b) Fuel for flame ionization detectors. Use a hydrogen-helium
mixture as the fuel. Make sure the mixture contains 40 +/- 2 percent
hydrogen and no more than 1 ppmC of organic carbon or 400 ppm of
CO2.
(c) Calibration and span gases. Apply the following provisions to
calibration and span gases:
(1) Use the following gas mixtures, as applicable, for calibrating
and spanning your analytical instruments:
(i) Propane in purified synthetic air. You may ask us to allow you
to use propane in purified nitrogen for high concentrations of propane.
(ii) CO in purified nitrogen.
(iii) NO and NO2 in purified nitrogen (the amount of
NO2 in this calibration gas must not exceed 5 percent of the
NO content).
(iv) Oxygen in purified nitrogen.
(v) CO2 in purified nitrogen.
(vi) Methane in purified synthetic air.
(2) The calibration gases in paragraph (c)(1) of this section must
be traceable to within one percent of NIST gas standards or other gas
standards we have approved. Span gases in paragraph (c)(1) of this
section must be accurate to
[[Page 68418]]
within two percent of true concentration, where true concentration
refers to NIST gas standards, or other gas standards we have approved.
Record concentrations of calibration gas as volume percent or volume
ppm.
(3) You may use gases for species other than those in paragraph
(c)(1) of this section (such as methanol in air gases used to determine
response factors), as long as they meet the following criteria:
(i) They are traceable to within +/-2 percent of NIST gas standards
or other standards we have approved.
(ii) They remain within +/-2 percent of the labeled concentration.
Show this by measuring quarterly with a precision of +/-2 percent (two
standard deviations) or by using another method we approve. You may
take multiple measurements. If the true concentration of the gas
changes by more than two percent, but less than ten percent, you may
relabel the gas with the new concentration.
(4) You may generate calibration and span gases using precision
blending devices (gas dividers) to dilute gases with purified nitrogen
or with purified synthetic air. Make sure the mixing device produces a
concentration of blended calibration gases that is accurate to within
+/- 1.5 percent. To do so, you must know the concentration of primary
gases used for blending to an accuracy of at least +/- 1 percent,
traceable to NIST gas standards or other gas standards we have
approved. For each calibration incorporating a blending device, verify
the blending accuracy between 15 and 50 percent of full scale. You may
optionally check the blending device with an instrument that is linear
by nature (for example, using NO gas with a CLD). Adjust the
instrument's span value with the span gas connected directly to it.
Check the blending device at the used settings to ensure that the
difference between nominal values and measured concentrations at each
point stays within +/- 0.5 percent of the nominal value.
(d) Oxygen interference gases. Gases to check oxygen interference
are mixtures of oxygen, nitrogen, and propane. The oxygen concentration
must be 20-22 percent and the propane concentration must be 50-90
percent of the maximum value in the most typically used FID range.
Independently measure the concentration of total hydrocarbons plus
impurities by chromatographic analysis or by dynamic blending.
Subpart D--Analyzer and Equipment Calibrations
Sec. 1065.301 Overview.
Calibrate all analyzers and equipment at least annually, but make
the actual frequency consistent with good engineering judgment. We may
establish other guidelines as appropriate. Calibrate following
specifications in one of three sources:
(a) Recommendations from the manufacturer of the analyzers or
equipment.
(b) 40 CFR part 86, subpart F or subpart N.
(c) 40 CFR part 90, subparts D and E, as applicable.
Sec. 1065.305 International calibration standards.
(a) You may ask to use international standards for calibration.
(b) You need not ask for approval to use standards that have been
shown to be traceable to NIST standards.
Sec. 1065.310 CVS calibration. [Reserved]
Sec. 1065.315 Torque calibration.
You must use one of two techniques to calibrate torque: the lever-
arm dead-weight or the transfer technique. You may use other techniques
if you show they are equally accurate. The NIST ``true value'' torque
is defined as the torque calculated by taking the product of an NIST
traceable weight or force and a sufficiently accurate horizontal
distance along a lever arm, corrected for the lever arm's hanging
torque.
(a) The lever-arm dead-weight technique involves placing known
weights at a known horizontal distance from the torque-measuring
device's center of rotation. You need two types of equipment:
(1) Calibration weights. This technique requires at least six
calibration weights for each range of torque-measuring device used.
Equally space the weights and make sure each one is traceable to NIST
weights. You also may use weights certified by a U.S. state
government's bureau of weights and measures. If your laboratory is
outside the U.S., see Sec. 1065.305 for information about using non-
NIST standards. You may account for effects of changes in gravitational
constant at the test site.
(2) Lever arm. This technique also requires a lever arm at least 20
inches long. Make sure the horizontal distance from the torque-
measurement device's centerline to the point where you apply the weight
is accurate to within +/-0.10 inches. You must balance the arm or know
its hanging torque to within +/-0.1 ft-lbs.
(b) The transfer technique involves calibrating a master load cell
(dynamometer case load cell). You may calibrate the master load cell
with known calibration weights at known horizontal distances. Or you
may use a hydraulically actuated, precalibrated, master load cell and
then transfer this calibration to the device that measures the flywheel
torque. The transfer technique involves three main steps:
(1) Precalibrate a master load cell or calibrate it following
paragraph (a)(1) of this section. Use known weights traceable to NIST
with the lever arms specified in paragraph (b)(2) of this section. Run
or vibrate the dynamometer during this calibration to reduce static
hysteresis.
(2) Use lever arms at least 20 inches long. The horizontal
distances from the master load cell's centerline to the dynamometer's
centerline and to the point where you apply weight or force must be
accurate to within +/-0.10 inches. Balance the arms or know their net
hanging torque to within +/-0.1 ft-lbs.
(3) Transfer calibration from the case or master load cell to the
torque-measuring device with the dynamometer operating at a constant
speed. Calibrate the torque-measurement device's readout to the master
load cell's torque readout at a minimum of six loads spaced about
equally across the full useful ranges of both measurement devices.
(Good engineering practice requires that both devices have about the
same useful ranges of torque measurement.) Transfer the calibration so
it meets the accuracy requirements in Sec. 1065.105(a)(2) for readouts
from the torque-measurement device.
Subpart E--Engine Selection, Preparation, and Service Accumulation
Sec. 1065.401 Selecting a test engine.
While all engine configurations within a certified engine family
must comply with the applicable standards in the standard-setting part,
you are not required to test each configuration for certification.
(a) Select for testing according to the following guidance the
engine configuration within the engine family that is most likely to
exceed an emission standard:
(1) Test the engine that we specify, whether we do this through
general guidance or give you specific instructions.
(2) If we do not tell you which engine to test, follow any
instructions in the standard-setting part.
(3) If we do not tell you which engine to test and the standard-
setting part does
[[Page 68419]]
not include specifications for selecting test engines, use good
engineering judgment to select the engine configuration within the
engine family that is most likely to exceed an emission standard.
(b) In the absence of other information, the following
characteristics are appropriate to consider when selecting the engine
to test:
(1) Maximum fueling rates.
(2) Maximum in-use engine speed (governed or ungoverned, as
applicable).
(3) Highest sales volume.
(c) We may select any engine configuration within the engine family
for our testing.
Sec. 1065.405 Preparing and servicing a test engine.
(a) If you are testing an emission-data engine for certification,
make sure you have built it to represent production engines.
(b) Run the test engine, with all emission-control systems
operating, long enough to stabilize emission levels. If you accumulate
50 hours of operation, you may consider emission levels stable without
measurement.
(c) Do not service the test engine before you stabilize emission
levels, unless we approve other maintenance in advance. This
prohibition does not apply to your recommended oil and filter changes
for newly produced engines, or to idle-speed adjustments.
(d) Select engine operation for accumulating operating hours on
your test engines to represent normal in-use operation for the engine
family.
(e) If you need more than 50 hours to stabilize emission levels,
record your reasons and the method you use to do this. Give us these
records if we ask for them.
Sec. 1065.410 Service limits for stabilized test engines.
(a) After you stabilize the test engine's emission levels, you may
do scheduled maintenance, other than during emission testing, as the
standard-setting part specifies.
(b) You may not do any unscheduled maintenance to the test engine
or its emission-control system or fuel system without our advance
approval. Unscheduled maintenance includes adjusting, repairing,
removing, disassembling, cleaning, or replacing the test engine. We may
approve routine maintenance that is not scheduled such as maintaining
the proper oil level.
(1) We may approve other unscheduled maintenance if all of the
following occur:
(i) You determine that a part failure or system malfunction (or the
associated repair) does not make the engine unrepresentative of
production engines in the field and does not require anyone to access
the combustion chamber.
(ii) Something clearly malfunctions (such as persistent misfire,
engine stall, overheating, fluid leakage, or loss of oil pressure) and
needs maintenance or repair.
(iii) You give us a chance to verify the extent of the malfunction
before you do the maintenance.
(2) If we determine that a part's failure or a system's malfunction
(or the associated repair) has made the engine unrepresentative of
production engines, you may no longer use it as a test engine.
(3) You may not do unscheduled maintenance based on emission
measurements from the test engine.
(4) Unless we approve otherwise in advance, you may not use
equipment, instruments, or tools to identify bad engine components
unless you specify they should be used for scheduled maintenance on
production engines. In this case, if they are not generally available,
you must also make them available at dealerships and other service
outlets.
(c) If you do maintenance that might affect emissions, you must
completely test the engine for emissions before and after the
maintenance, unless we waive this requirement.
(d) If your test engine has a major mechanical failure that
requires you to take it apart, you may no longer use it as a test
engine.
Sec. 1065.415 Durability demonstration.
If the standard-setting part requires durability testing, you must
accumulate service in a way that represents how you expect the engine
to operate in use. You may accumulate service hours using an
accelerated schedule, such as through continuous operation.
(a) Maintenance. The following limits apply to the maintenance that
we allow you to do on test engine:
(1) You may perform scheduled maintenance that you recommend to
operators, but only if it is consistent with the standard-setting
part's restrictions.
(2) You may perform additional maintenance only if we approve it in
advance, as specified in Sec. 1065.410(b).
(3) If your test engine has a major mechanical failure that
requires you to take it apart, you may no longer use it as a test
engine.
(b) Emission measurements. You must measure emissions following two
main requirements:
(1) Perform emission tests to determine deterioration factors
consistent with good engineering judgment. Evenly space any tests
between the first and last test points throughout the durability
period.
(2) Perform emission tests following the provisions of this part
and the standard-setting part.
Subpart F--Running an Emission Test
Sec. 1065.501 Overview of the engine dynamometer test procedures.
(a) The engine dynamometer test procedure measures brake-specific
emissions of hydrocarbons (total and nonmethane, as applicable), carbon
monoxide, and oxides of nitrogen. To perform this test procedure, you
first dilute exhaust emissions with ambient air and collect a
continuous proportional sample for analysis, then analyze the composite
samples (either in bags after the test or continuously during the
test). The general test procedure consists of a test cycle made of one
or more segments (check the standard-setting part for specific cycles):
(1) Either a cold-start cycle (where you measure emissions) or a
warm-up cycle (where you do not measure emissions).
(2) A hot-start transient test (some test cycles may omit engine
starting from the ``hot-start'' cycle).
(3) A steady-state test.
(b) Measure power using the dynamometer's feedback signals for
torque and speed. The power measurement produces a brake kilowatt-hour
value that allows you to calculate brake-specific emissions (see
Subpart G of this part).
(c) Prepare engines for testing consistent with Sec. 1065.10(c)(1)
and according to the following provisions:
(1) When you test an engine or operate it for service accumulation,
use the complete engine with all emission-control devices installed and
functioning.
(2) Install the fan for any air-cooled engine (if applicable).
(3) You may install accessories such as an oil cooler, alternators,
and air compressors or simulate their loading if they are typical of
in-use operation. Apply this loading during all testing operations,
including mapping.
(4) You may install a production-type starter on the engine.
(5) Cool the engine in a way that will maintain its operating
temperatures including the intake air, oil, water temperatures about
the same as they would be during normal operation. You may use
auxiliary fans if necessary. You may use rust inhibitors and
lubrication additives, up to the levels that the additive manufacturer
recommends.
[[Page 68420]]
You may also use antifreeze mixtures and other coolants typical of
those approved for use by the manufacturer.
(6) Use representative exhaust and air-intake systems. Make sure
the exhaust restriction is 80 to 100 percent of the recommended maximum
specified exhaust restriction and the air inlet restriction is between
that of a clean filter and the maximum restriction specification. As
the manufacturer, you are liable for emission compliance from the
minimum in-use restrictions to the maximum restrictions you specify for
that particular engine.
Sec. 1065.510 Engine mapping procedures.
(a) Torque map. Map your engine's torque while it is mounted on the
dynamometer. Use the torque curve resulting from the mapping to convert
the normalized torque values in the engine cycle to actual torque
values for the test cycle. Make sure the speed ranges at least from the
warm no-load idle speed to 105 percent of the maximum test speed.
Because you determine the maximum test speed from the torque map, you
may have to perform a preliminary torque map to determine the full
mapping range. You may perform this preliminary torque map while the
engine warms up. To map the engine, do the following things in
sequence:
(1) Warm up the engine so oil and water temperatures (on an
absolute scale such as the Kelvin scale) vary by less than two percent
for two minutes; or until the thermostat opens if the engine-coolant
system includes a thermostat.
(2) Operate the engine at the warm no-load idle speed.
(3) Fully open the throttle.
(4) While maintaining wide-open throttle and full-load, keep the
engine at minimum speed for at least 15 seconds. Record the average
torque during the last 5 seconds.
(5) In increments of 100+/-20 rpm, determine the maximum torque
curve for the full speed range. Hold each test point for 15 seconds and
record the average torque over the last 5 seconds. You may use larger
increments for engines with maximum test speed over 4000 rpm, as long
as you include at least 40 points and space them evenly.
(6) Fit all data points recorded with a cubic spline, Akima, or
other technique we approve in advance. The resultant curve must be
accurate to within +/-1.0 ft-lbs. of all recorded engine torques.
(b) Torque map with continual engine speed sweep. In place of
paragraphs (a)(1) through (a)(4) of this section, you may do a
continual sweep of engine speed. While operating at wide-open throttle,
increase the engine speed at an average rate of 8+/-1 rpm/sec over the
full speed range. You may use higher sweeping rates for naturally-
aspirated engines, in accordance with good engineering judgment. Record
speed and torque points at a rate of at least one point per second.
Connect all points generated under this approach by linear
interpolation.
(c) Alternate mapping. You may use other mapping techniques if you
believe those in paragraphs (a) and (b) of this section are unsafe or
unrepresentative for any engine or engine family. These alternate
techniques must satisfy the intent of the specified mapping
procedures--to determine the maximum available torque at all engine
speeds that occur during the test cycles. Report deviations from this
section's mapping techniques for reasons of safety or
representativeness. In no case, however, may you use descending
continual sweeps of engine speed for governed or turbocharged engines.
(d) Replicate tests. You need not map an engine before every test,
but you do need to remap the engine in any of the following situations:
(1) Good engineering judgment determines that an unreasonable
amount of time has passed since the last map.
(2) The barometric pressure before the test begins has changed more
than 25 mm Hg from the average barometric pressure observed during the
map.
(3) The engine has undergone physical changes or recalibration that
might affect its performance.
(e) Power map. Where applicable, generate a power map using the
procedures this section specifies for torque maps. You may generate the
power map directly or convert the torque map to a power map using
engine speeds. The power map is also called a lug curve.
(f) Cycles based only on torque/power at maximum test speed. If the
applicable test cycle for your engine does not require map information
for engine speeds other than the maximum test speed, you may make the
following simplifications:
(1) You need not perform the entire torque or power map, as long as
you map the engines for speeds between 75 and 105 percent of the
maximum test speed.
(2) You need not remap an engine according to paragraph (d) of this
section. You need only verify the maximum torque or power at maximum
test speed.
Sec. 1065.515 Test cycle generation.
(a) Denormalizing test cycles. The standard-setting parts establish
the applicable test cycles consisting of second-by-second
specifications for normalized torque and speed for transient cycles, or
modal specifications for normalized torque and speed (or power and
speed) for steady-state cycles. You must denormalize these values to
get actual torque and speed for your engine.
(1) Torque is normalized to a maximum-torque value. Check the
standard-setting part to see if it is normalized based on the maximum
torque at the given speed or based on the maximum torque for all
speeds. To denormalize the torque values in the cycle, use the engine's
maximum-torque point or its torque map (Sec. 1065.510 describes how to
generate the torque map).
(2) Power is normalized to a maximum-power value. Check the
standard-setting part to see if it is normalized based on the maximum
power at the given speed or based on the maximum power for all speeds.
To denormalize the power values in the cycle, use the engine's maximum-
power point or its power map (Sec. 1065.510 describes how to generate
the power map).
(3) To denormalize speed, use the following equation:
Actual engine speed = (0.01) x (%engine speed) x (Maximum test speed--
warm idle speed) + warm idle speed
(4) Paragraph (d) of this section describes how to calculate
maximum test speed.
(b) Example of denormalizing a test points. For an engine with
maximum test speed of 3800 rpm and warm idle speed of 600 rpm,
denormalize the following test point: percent engine speed = 43,
percent torque = 82.
(1) Calculate actual engine speed. The following equation applies
for this example:
Actual engine speed = (0.01) x (43) x (3800-600) + 600 = 1976 rpm.
(2) Determine actual torque. Determine the maximum observed torque
at 1976 rpm from the maximum torque curve. Then multiply this value
(for example, 358 ft-lbs.) by 0.82. The resulting actual torque is 294
ft-lbs.
(c) Cold-start enhancement devices. If an engine has a properly
operating automatic enhancement device for cold starts, let it override
the zero-percent speed specified in the test cycles.
(d) Maximum test speed. For constant-speed engines, maximum test
speed is the same as the engine's maximum operating speed in use.
Maximum test speed for variable-speed engines occurs on the lug curve
at the
[[Page 68421]]
point farthest from the origin on a plot of power vs. speed. To find
this speed, follow three main steps:
(1) Generate the lug curve. Before testing an engine for emissions,
generate data points for maximum measured brake power with varying
engine speed (see Sec. 1065.510). These data points form the lug
curve.
(2) Normalize the lug curve. To normalize the lug curve, do three
things:
(i) Identify the point (power and speed) on the lug curve where
maximum power occurs.
(ii) Normalize the power values of the lug curve--divide them by
the maximum power and multiply the resulting values by 100.
(iii) Normalize the engine speed values of the lug curve--divide
them by the speed at which maximum power occurs and multiply the
resulting values by 100.
(3) Determine maximum test speed. Calculate the maximum test speed
from the following speed-factor analysis:
(i) For a given power-speed point, the speed factor is the
normalized distance to the power-speed point from the zero-power, zero-
speed point. Compute the speed factor's value:
[GRAPHIC]
[TIFF OMITTED]
TR08NO02.015
(ii) Determine the maximum value of speed factors for all the
power-speed data points on the lug curve. Maximum test speed is the
speed at which the speed factor's maximum value occurs. Note that this
maximum test speed is the 100-percent speed point for normalized
transient duty cycles.
(e) Intermediate test speed. Determine intermediate test speed with
the following provisions:
(1) If peak torque speed is 60 to 75 percent of the maximum test
speed, the intermediate speed point is at that same speed.
(2) If peak torque speed is less than 60 percent of the maximum
test speed, the intermediate speed point is at 60 percent of maximum
test speed.
(3) If peak torque speed is greater than 75 percent of the maximum
test speed, the intermediate speed point is at 75 percent of maximum
test speed.
Sec. 1065.520 Engine starting, restarting, and shutdown.
Unless the standard-setting part specifies otherwise, follow the
steps in this section to start and shut down the test engine:
(a) Engine starting. Start the engine according to the
manufacturer's recommended starting procedure in the owner's manual,
using either a production starter motor or the dynamometer. Use the
dynamometer to crank (or motor) the engine at the typical in-use
cranking speed with a fully charged battery (nominal speed +/-10
percent), accelerating the engine to cranking speed in the same time it
would take with a starter motor (nominal +/-0.5 seconds). Stop motoring
by the dynamometer within one second of starting the engine. The
cycle's free-idle period begins when you determine that the engine has
started.
(1) If the engine does not start after 15 seconds of cranking, stop
cranking and determine the reason it failed to start. While diagnosing
the problem, turn off the device that measures gas flow (or revolution
counter) on the constant-volume sampler (and all integrators when
measuring emissions continuously). Also, turn off the constant-volume
sampler or disconnect the exhaust tube from the tailpipe. If failure to
start is an operational error, reschedule the engine for testing (this
may require soaking the engine if the test requires a cold-start).
(2) If longer cranking times are necessary, you may use them
instead of the 15-second limit, as long as the owner's manual and the
service-repair manual describe the longer cranking times as normal.
(3) If an engine malfunction causes a failure to start, you may
correct it in less than 30 minutes and continue the test. Reactivate
the sampling system at the same time cranking begins. When the engine
starts, begin the timing sequence. If an engine malfunction causes a
failure to start, and you cannot restart the engine, the test is void.
(b) Engine stalling. Respond to engine stalling as follows:
(1) If the engine stalls during the warm-up period, the initial
idle period of test, or the steady-state segment, you may restart the
engine immediately using the appropriate starting procedure and
continue the test.
(2) If the engine stalls at any other time, the test is void.
(c) Engine shutdown. Shut the engine down according to the
manufacturer's specifications.
Sec. 1065.525 Engine dynamometer test run.
Take the following steps for each test:
(a) Prepare the engine, dynamometer, and sampling system. Change
filters or other replaceable items and check for leaks as necessary.
(b) If you are using bag samples, connect evacuated sample-
collection bags to the collection system for the dilute exhaust and
dilution air sample.
(c) Attach the CVS to the engine's exhaust system any time before
starting the CVS.
(d) Start the CVS (if not already started), the sample pumps, the
engine cooling fans, and the data-collection system. Before the test
begins, preheat the CVS's heat exchanger (if used) and the heated
components of any continuous sampling systems to designated operating
temperatures.
(e) Adjust the sample flow rates to the desired levels and set to
zero the devices in the CVS that measure gas flow. The venturi design
fixes the sample flow rate in a CFV-CVS.
(f) Start the engine if engine starting is not part of the test
cycle, as specified in the standard-setting part.
(g) Run the test cycle specified in the standard-setting part and
collect the test data.
(h) As soon as practical after the test cycle is complete, analyze
the bag samples.
Sec. 1065.530 Test cycle validation criteria.
(a) Steady-state emission testing. Make sure your engine's speeds
and loads stay within +/-2 percent of the set point during the sampling
period.
(b) Transient emission testing performed by EPA. Emission tests
must meet the specifications of this paragraph (b). Otherwise, they do
not comply with the test cycle requirements of the standard-setting
part, unless we determine the cause of the failure to meet these
specifications is related to the engine rather than the test equipment.
(1) Shifting feedback signals. The time lag between the feedback
and reference-cycle values may bias results. To reduce this effect, you
may advance or delay the entire sequence of engine-speed and torque-
feedback signals with respect to the reference sequence for speed and
torque. If you shift the feedback signals, you must shift speed and
torque the same amount in the same direction.
(2) Calculating brake kilowatt-hour emissions. Calculate brake
kilowatt-hour emissions for each pair of feedback values recorded for
engine speed and torque. Also calculate the reference brake kilowatt-
hour for each pair of reference values for engine speed and torque.
Calculate to five significant figures.
(3) Performing regression-line analysis. Perform regression
analysis to calculate validation statistics as follows:
(i) Perform linear regressions of feedback value on reference value
for speed, torque, and brake power on 1 Hz data after the feedback
shift has occurred (see paragraph (b)(1) of this section). Use the
method of least squares, with the best-fit equation having the form:
y = mx + b
[[Page 68422]]
Where:
y = The feedback (actual) value of speed (rpm), torque (ft-lbs.), or
brake power.
m = Slope of the regression line.
x = The reference value (speed, torque, or brake power).
b = The y-intercept of the regression line.
(ii) Calculate the standard error of estimate (SE) of y on x and
the coefficient of determination (r\2\) for each regression line.
(iii) For a valid test, make sure the feedback cycle's integrated
brake kilowatt-hour is within 5 percent of the reference cycle's
integrated brake kilowatt-hour. Also, ensure that the slope, intercept,
standard error, and coefficient of determination meet the criteria in
the following table (you may delete individual points from the
regression analyses, consistent with good engineering judgment):
Table 1 of Sec. 1065.530.--Statistical Criteria for Validating Test Cycles
----------------------------------------------------------------------------------------------------------------
Speed Torque Power
----------------------------------------------------------------------------------------------------------------
1. Slope of the regression line (m).. 0.980 to 1.020......... 0.880 to 1.030......... 0.880 to 1.030.
--------------------------------------
2. Y intercept of the regression line [verbarlm]b[verbarlm]
[verbarlm]b[verbarlm]
[verbarlm]b[verbarlm]
(b). <= 40 rpm. <= 5.0 percent of <= 3.0 percent of
maximum torque from maximum torque from
power map. power map.
--------------------------------------
3. Standard error of the estimate of 100 rpm................ 15 percent of maximum 10 percent of maximum
Y on X (SE). torque from power map. power from power map.
--------------------------------------
4. Coefficient of determination r\2\ £= 0.970 r\2\ £= 0.900 r\2\ £=
(r\2\). 0.900.
----------------------------------------------------------------------------------------------------------------
(c) Transient testing performed by manufacturers. Emission tests
that meet the specifications of paragraph (b) of this section satisfy
the standard-setting part's requirements for test cycles. You may ask
to use a dynamometer that cannot meet those specifications, consistent
with good engineering practice. We will approve your request as long as
using the alternate dynamometer does not affect your ability to show
that you comply with all applicable emission standards.
Subpart G--Data Analysis and Calculations
Sec. 1065.601 Overview.
This subpart describes how to use the responses on the analyzers
and other meters to calculate final gram per kilowatt-hour emission
rates.
Note: Volume and density values used in these calculations are
generally corrected to standard conditions of 20[deg]C and 101.3
kPa.)
Sec. 1065.605 Required records.
Retain the following information for each test:
(a) Test number.
(b) System or device tested (brief description).
(c) Date and time of day for each part of the test schedule.
(d) Test results.
(e) Operator's name.
(f) Engine: ID number, manufacturer, model year, emission
standards, engine family, basic engine description, fuel system, engine
code, and idle speed, as applicable.
(g) Dynamometer: Dynamometer identification, records to verify
compliance with the duty cycle requirements of the test.
(h) Gas analyzers: Analyzer bench identification, analyzer ranges,
recordings of analyzer output during zero, span, and sample readings.
(i) Recorder charts: Test number, date, identification, operator's
name, and identification of the measurements recorded.
(j) Test cell barometric pressure, ambient temperature, and
humidity as required. (Some test systems may require continuous
measurements; others may require a single measurement, or measurements
before and after the test.)
(k) Temperatures: Records to verify compliance with the ambient
temperature requirements throughout the test procedure.
(l) CFV-CVS: Total dilute exhaust volume (Vmix) for each phase of
the exhaust test.
(m) PDP-CVS: Test measurements for calculating the total dilute
exhaust volume (Vmix), and the Vmix for each phase of the exhaust test.
(n) The humidity of the dilution air.
Note: If you do not use conditioning columns, this measurement
is not necessary. If you use conditioning columns and take the
dilution air from the test cell, you may use the ambient humidity
for this measurement.
Sec. 1065.610 Bag sample analysis.
(a) Zero the analyzers and obtain a stable zero reading. Recheck
after tests.
(b) Introduce span gases and set instrument gains. To avoid errors,
span and calibrate at the same flow rates used to analyze the test
sample. Span gases should have concentrations equal to 75 to 100
percent of full scale. If gain has shifted significantly on the
analyzers, check the calibrations. Show actual concentrations on the
chart.
(c) Check zeroes; if necessary, repeat the procedure in paragraphs
(a) and (b) of this section.
(d) Check flow rates and pressures.
(e) Measure HC, CO, CO2, and NOX
concentrations of samples.
(f) Check zero and span points. If the difference is greater than 2
percent of full scale, repeat the procedure in paragraphs (a) through
(e) of this section.
Sec. 1065.615 Bag sample calculations.
(a) Calculate the dilution factor. The dilution factor is the ratio
of the total volume of the raw exhaust to the total volume of the
diluted exhaust. It is calculated as 134,000 divided by the sum of the
diluted ppmC concentrations of carbon-containing compounds in the
exhaust, as follows:
DF = 134,000/
(CO2sample+THCsample+COsample),
Where:
CO2sample and COsample are expressed as ppm, and
THCsample is expressed as ppmC.
(b) Calculate mass emission rates (g/test) for the transient
segment using the general equation in paragraph (b)(1) of this section:
(1) The general equation is:
Emission rate = (total dilute exhaust flow volume)(ppm)(density
factor)/10\6\
Mx = (Vmix)(Ci)(fdi)/
10\6\
Where:
Mx = Mass emission rate in g/test segment.
Vmix = Total dilute exhaust flow volume flow in m\3\ per
test segment corrected to 20[deg]C and 101.3 kPa.
Ci = The concentration of species i, in ppm or ppmC,
corrected for background
[[Page 68423]]
contribution according to the equation in paragraph (b)(2) of this
section.
fdi = The density factor for species i. The density factors
are 576.8 g/m\3\ for THC, 1913 g/m\3\ for NOX, and 1164 g/
m\3\ for CO.
(2) The equation to calculate Ci is:
Ci = Csample-Cbackground [1--(1/DF)]
Where:
Csample = Concentration of species i in the diluted exhaust
sample, in ppm or ppmC.
Cbackground = Concentration of species i in the dilution air
background sample, in ppm or ppmC.
DF = Dilution factor, as calculated in paragraph (a) of this section.
(c) Calculate total brake work (kW-hr) done during the emissions
sampling period of each segment or mode.
(d) Calculate emissions in g/kW-hr by dividing the mass emission
rate (g/test segment) by the total brake work for the test segment.
(e) Apply deterioration factors or other adjustment factors to the
brake-specific emission rate in paragraph (e) as specified in the
standard-setting part.
Subpart H--Particulate Measurements [Reserved]
Subpart I--Testing With Oxygenated Fuels
Sec. 1065.801 Applicability.
(a) This subpart applies for testing with oxygenated fuels. Except
where specified otherwise in the standard-setting part, compliance with
this subpart is not required for fuels that contain less than 25
percent oxygenated compounds by volume. For example, you generally
would not need to follow the requirements of this subpart for tests
performed using a fuel that was 10 percent ethanol and 90 percent
gasoline, but you would need to follow these requirements for tests
performed using a fuel that was 85 percent ethanol and 15 percent
gasoline.
(b) This subpart specifies sampling procedures and calculations
that are different than those used for non-oxygenated fuels. The other
test procedures of this part apply for testing with oxygenated fuels.
Sec. 1065.805 Sampling system.
(a) Use the sampling procedures specified in 40 CFR part 86 for
methanol and formaldehyde to measure alcohols and aldehydes in the
exhaust. This requires the following:
(1) Bubbling a sample of the exhaust through water to collect the
alcohols.
(2) Passing a sample of the exhaust through cartridges impregnated
with 2,4-dinitrophenylhydrazine to measure aldehydes.
(b) Use good engineering judgment to measure other oxygenated
compounds in the exhaust.
Sec. 1065.810 Calculations.
(a) THCE emissions. (1) Calculate THCE emissions as the sum of the
mass of the nonoxygenated hydrocarbons in the exhaust and the carbon-
equivalent mass of each measured oxygenated species in the exhaust.
(2) Calculate carbon-equivalent mass of each measured oxygenated
species from the following equation:
Carbon equivalent = 13.8756 x MOC/MWPC
Where:
MOC is the mass of the oxygenated compound in the exhaust, and MWPC
is the molecular weight of compound per carbon atom of compound.
(b) NMHCE emissions. Calculate NMHCE emissions as either:
(1) The sum of the mass of the nonoxygenated nonmethane
hydrocarbons in the exhaust and the carbon-equivalent mass of each
measured oxygenated species in the exhaust.
(2) THCE minus the mass of methane in the exhaust.
(c) Sample calculation. (1) Assume the following emissions for a
test: 40.00 grams of nonoxygenated hydrocarbons, 100.00 grams of
ethanol, and 10.00 grams of acetaldehyde, and 1.00 gram of
formaldehyde.
(2) The carbon-equivalent of the masses of oxygenated compounds
are:
(i) 13.8756 x 100.00/(46.068/2) = 60.24 grams of ethanol.
(ii) 13.8756 x 10.00/(44.052/2) = 6.30 grams of acetaldehyde.
(iii) 13.8756 x 1.00/(30.026) = 0.46 grams of formaldehyde.
(3) THCE = 40.00 + 60.24 + 6.30 + 0.46 = 107.00 grams per test.
Subpart J--Field Testing
Sec. 1065.901 Applicability.
(a) The test procedures in this subpart measure brake-specific
emissions from engines while they remain installed in vehicles or
equipment in the field.
(b) These test procedures apply to your engines as specified in the
standard-setting part. For example, part 1048 of this chapter specifies
emission standard to be used for in-use tests conducted in accordance
with the provisions of this part. Unless this subpart is specifically
mentioned in the standard-setting part, compliance with the provisions
of this subpart is not required.
Sec. 1065.905 General provisions.
(a) Unless the standard-setting part specifies deviations from the
provisions of this subpart, testing conducted under this subpart must
conform to all of the provisions of this subpart.
(b) Testing conducted under this subpart may include any normal in-
use operation of the engine.
Sec. 1065.910 Measurement accuracy and precision.
(a) Measurement systems used for in-use testing must be accurate to
within +/-5 percent compared to engine dynamometer testing conducted
according to the test procedures of this part that are applicable for
your engine. These systems must also have a precision of +/-5 percent
or better. Determine accuracy and precision of an in-use system by
simultaneously measuring emissions using the engine-dynamometer test
procedures of this part and the in-use system. To have a statistically
valid sample, measure emissions during at least 3 tests each for at
least 3 different engines. You must conduct these verification tests
using the test cycle specified in the standard-setting part, unless we
approve a different test cycle.
(1) A system must meet the following conditions to be considered
sufficiently accurate:
(i) The correlation coefficient (r) for a least-squares linear fit
that includes the origin must be 0.95 or higher.
(ii) The average ratio (for all tests) of the emission rate from
the in-use system divided by the emission rate from the dynamometer
procedure must be 0.97 to 1.05.
(2) For a system to be considered sufficiently precise, the average
coefficient of variance for all engines must be 5 percent or less for
each pollutant.
Note: Increasing the length of the sampling period may be an
effective way to improve precision.
(b) Measurement systems that conform to the provisions of
Sec. Sec. 1065.915 through 1065.950 are considered to be in compliance
with the accuracy and precision requirements of paragraph (a) of this
section.
Sec. 1065.915 Equipment specifications for SI engines.
This section describes equipment you may use to measure in-use
emissions. You may use other equipment and measurement systems that
conform to the requirements of Sec. Sec. 1065.905 and 1065.910.
(a) The primary components of the in-use measurement system are a
mass air flow sensor, a portable FID, a zirconia-
[[Page 68424]]
based NOX sensor, a zirconia-based air/fuel ratio sensor,
and a portable NDIR analyzer.
(1) The mass air flow sensor must meet the requirements of Sec.
1065.930.
(2) The portable FID must meet the requirements of Sec. 1065.935.
(3) The NOX and air/fuel sensors must meet the
requirements of Sec. 1065.940
(4) The NDIR analyzer must meet the requirements of Sec. 1065.945.
(b) You must measure the following parameters continuously at a
rate of 3 Hz or higher and store the data electronically:
(1) THC, NOX, CO concentrations.
(2) Mass air-fuel ratio.
(3) Intake air flow rate.
(4) Engine speed.
(5) Parameters used to calculate torque.
(c) You must minimize sample line length for any analyzers that
require a physical sample be drawn from the exhaust to the analyzer
(i.e., THC and CO analyzers). You must draw these samples at a constant
flow rate. In no case may you use any combination of sample line length
and sample flow rate that would require more than 10 seconds for the
analyzer to reach 90 percent of its final response after a step change
to the input concentration at the opening of the sample probe. For
residence time delays between 1 and 10 seconds, you must correct the
measurements to be consistent with the data for engine speed, torque,
and air intake. You may also correct other measurements with less than
delays less than 1 second.
(d) You may insert the sample probes and sensors into the exhaust
pipe, or mount them in an exhaust extension that is connected to the
exhaust pipe with negligible leaking. Place the sample probes and
sensors close enough to the center line of the exhaust pipe to minimize
boundary layer effects from the wall.
Sec. 1065.920 Equipment setup and test run for SI engines.
This section describes how to set up the equipment specified in
Sec. 1065.915, and how to use it to measure in-use emissions from SI
engines.
(a) Inspect the vehicle or equipment to determine whether it meets
any applicable requirements of the standard-setting part. This may
include requirements related to model year, accumulated hours of
operation, fuel specifications, maintenance history, engine
temperatures, etc.
(b) Perform calibrations as specified in this subpart. In the
field, this generally will require only zeroing and spanning the
instruments. However, each instrument must have been fully calibrated
according to the instrument manufacturer's specifications. Nonlinear
calibrations generated previously from the full calibration may be used
after zeroing and spanning the instruments. Spanning can be performed
using a single gas bottle, consistent with good engineering practice,
and provided that stability of the span mixture has been demonstrated.
(c) Connect the data recorder (with any necessary signal
interpreters or converters) to the engine's electronic control module.
(d) Disconnect the air intake system, as necessary, to attach the
mass air flow sensor. Reconnect the system after attaching the mass air
flow sensor.
(e) Attach the sample extension to the exhaust outlet.
(f) Turn on instruments and allow them to warm up as necessary.
(g) Begin sampling. You do not need to begin recording the data at
this point.
(h) Begin operating the vehicle or equipment in a normal manner.
Note: We may require you to operate the vehicle or equipment in
a specific manner.
(i) Begin recording engine speed, engine torque (or surrogate),
intake air flow, emissions data (THC, NOX, CO, air/fuel
ratio), and time. This time marks the beginning of the sampling period.
(j) Continue recording data and operating the vehicle or equipment
in a normal manner until the end of the sampling period. The length of
the sampling period is based on good engineering practice, the
precision requirements of Sec. 1065.910, and applicable limits in the
standard-setting part.
(k) You may measure background concentrations and correct measured
emission values accordingly. However, if any background corrections are
equivalent to 5 percent or more of the maximum emissions allowed by the
applicable standard, the test shall be voided and repeated in an
environment with lower background concentrations.
Sec. 1065.925 Calculations.
(a) [Reserved]
(b) Convert emission analyzer data to instantaneous concentrations
in ppm (ppmC for the FID).
(c) Calculate instantaneous exhaust volumetric flow rates in
standard m\3\/hr (volume and density values used in these calculations
are corrected to standard conditions of 20 [deg]C and 101.3 kPa.).
Calculate exhaust volumetric flow rate from the following equation:
Exhaust volumetric flow rate = (intake air mass flow rate)(1+mass fuel/
air ratio)/(density of exhaust)
(1) If you do not know the instantaneous density of the exhaust,
use the minimum density of the exhaust that occurs over the course of
the test, corrected to standard conditions.
(2) For gasoline-fueled engines designed to be operated at
stoichiometric fuel/air ratios, you may assume that the density of the
exhaust is 1202 g/m\3\ at standard conditions of 20 [deg]C and 101.3
kPa.
(3) For LPG-fueled engines designed to be operated at
stoichiometric fuel/air ratios, you may assume that the density of the
exhaust is 1175 g/m\3\ at standard conditions of 20 [deg]C and 101.3
kPa.
(4) For CNG-fueled engines designed to be operated at
stoichiometric fuel/air ratios, you may assume that the density of the
exhaust is 1149 g/m\3\ at standard conditions of 20 [deg]C and 101.3
kPa.
(d) Calculate instantaneous emission rates (g/hr) using the
following general equation:
Emission rate = (exhaust volumetric flow rate)(ppm)(density factor)/
106
Where:
Density factors are 576.8 g/m3 for THC, 1913 g/
m3 for NOX, 1164 g/m3 for CO.
(e) Integrate instantaneous emission rates for the entire specified
sample period.
(f) Determine instantaneous brake torque and speed.
(g) Calculate instantaneous brake power.
(h) Integrate instantaneous brake power for the entire specified
sample period.
(i) Divide the integrated emission rates by the integrated brake
power. These are your final brake-specific emission rates.
Sec. 1065.930 Specifications for mass air flow sensors.
(a) Measure the intake air flow using the engine's mass air flow
sensor. If the engine is not equipped with a mass air flow sensor, you
need to install one.
(b) The sensor design must have an accuracy and precision of +/-5
percent under steady-state laboratory conditions.
(c) The sensor must reach at least 90 percent of its final response
within 0.3 seconds after any step change to the flow rate greater than
or equal 80 percent of full scale.
(d) Calibrate the sensor according to good engineering practice.
Verify for each engine before testing that the sensor accurately reads
the idle intake air flow rate based on measured manifold temperature
(TM) and pressure PM). Use the following
equation:
[[Page 68425]]
Intake air flow = (displacement)(rpm)(volumetric
efficiency)(PM/101.3 kPa)(293.15 K/TM)
Sec. 1065.935 Specifications for THC analyzers.
(a) Use a flame ionization detector (FID).
(b) The analyzer must have an accuracy and precision of +/-2
percent of point or better under steady-state laboratory conditions.
(c) The analyzer must reach at least 90 percent of its final
response within 1.0 second after any step change to the input
concentration greater than or equal 80 percent of full scale.
(d) Zero and span the analyzer daily during testing. Calibrate it
according to the analyzer manufacturer's specifications.
Sec. 1065.940 Specifications for NOX and air/fuel sensors.
(a) Use stabilized zirconia-based sensors.
(b) The sensors must have an accuracy and precision of +/-2 percent
of point or better under steady-state laboratory conditions.
(c) The sensors must reach at least 90 percent of its final
response within 1.0 second after any step change to the input
concentration greater than or equal 80 percent of full scale.
(d) The sensors must be zeroed and spanned daily during testing,
and must be calibrated according to the sensor manufacturer's
specifications.
Sec. 1065.945 Specifications for CO analyzers.
(a) Use a non-dispersive infrared (NDIR) detector that is
compensated for CO2 and water interference.
(b) The analyzer must have an accuracy and precision of +/-2
percent of point or better under steady-state laboratory conditions.
(c) The analyzer must reach at least 90 percent of its final
response within 5.0 second after any step change to the input
concentration greater than or equal 80 percent of full scale.
(d) The analyzer must be zeroed and spanned daily during testing,
and must be calibrated according to the analyzer manufacturer's
specifications.
Sec. 1065.950 Specifications for speed and torque measurement.
(a) Determine torque from a previously determined relationship of
torque and engine speed, throttle position, and/or manifold absolute
pressure. Torque estimates must be between 85 percent and 105 percent
of the true value. You can demonstrate compliance with this accuracy
requirement using steady-state laboratory data.
(b) Measure speed from the engine's electronic control module.
Speed estimates must be within +/-5 rpm of the true value.
Subpart K--Definitions and Other Reference Information
Sec. 1065.1001 Definitions.
The following definitions apply to this part. The definitions apply
to all subparts unless we note otherwise. All undefined terms have the
meaning the Act gives to them. The definitions follow:
Accuracy means the maximum difference between a measured or
calculated value and the true value, where the true value is determined
by NIST.
Act means the Clean Air Act, as amended, 42 U.S.C. 7401 et seq.
Adjustable parameter means any device, system, or element of design
that someone can adjust (including those which are difficult to access)
and that, if adjusted, may affect emissions or engine performance
during emission testing or normal in-use operation.
Aftertreatment means relating to any system, component, or
technology mounted downstream of the exhaust valve or exhaust port
whose design function is to reduce exhaust emissions.
Auxiliary emission-control device means any element of design that
senses temperature, engine speed, motive speed, transmission gear,
atmospheric pressure, manifold pressure or vacuum, or any other
parameter to activate, modulate, delay, or deactivate the operation of
any part of the emission-control system. This also includes any other
feature that causes in-use emissions to be higher than those measured
under test conditions, except as we allow under this part.
Brake power has the meaning given in the standard-setting part. If
it is not defined in the standard-setting part, brake power means the
usable power output of the engine not including power required to
operate fuel pumps, oil pumps, or coolant pumps.
Calibration means the set of specifications and tolerances specific
to a particular design, version, or application of a component or
assembly capable of functionally describing its operation over its
working range.
Certification means obtaining a certificate of conformity for an
engine family that complies with the emission standards and
requirements in this part.
Compression-ignition means relating to a type of reciprocating,
internal-combustion engine that is not a spark-ignition engine.
Constant-speed engine means an engine governed to operate only at
its rated speed.
Designated Officer means the Manager, Engine Programs Group (6405-
J), U.S. Environmental Protection Agency, 1200 Pennsylvania Ave.,
Washington, DC 20460.
Emission-control system means any device, system, or element of
design that controls or reduces the regulated emissions from an engine.
Emission-data engine means an engine that is tested for
certification.
Emission-related maintenance means maintenance that substantially
affects emissions or is likely to substantially affect emissions
deterioration.
Engine means an engine to which this part applies.
Engine-based means having emission standards related to
measurements using an engine dynamometer, in units of grams of
pollutant per kilowatt-hour.
Engine family means a group of engines with similar emission
characteristics, as specified in the standard-setting part.
Equipment-based or vehicle-based means relating to programs that
require that a piece of equipment of vehicle be certified, rather than
only the engine.
Fuel system means all components involved in transporting,
metering, and mixing the fuel from the fuel tank to the combustion
chamber(s), including the fuel tank, fuel tank cap, fuel pump, fuel
filters, fuel lines, carburetor or fuel-injection components, and all
fuel-system vents.
Fuel type means a general category of fuels such as gasoline or
LPG. There can be multiple grades within a single type of fuel, such as
summer-grade gasoline and winter-grade gasoline.
Good engineering judgment has the meaning we give it in Sec.
1068.5 of this chapter.
Identification number means a unique specification (for example,
model number/serial number combination) that allows someone to
distinguish a particular engine from other similar engines.
Idle speed means the lowest engine speed with zero load.
Note: Warm idle speed is the idle speed of a warmed-up engine.
Manufacturer has the meaning given in section 216(1) of the Act. In
general, this term includes any person who manufactures an engine for
sale in the United States or otherwise introduces a new engine into
commerce in the United States. This includes importers that import
engines for resale.
Maximum test torque means:
[[Page 68426]]
(1) For throttled engines, the torque output observed at wide-open
throttle at a given speed.
(2) For non-throttled engines, the torque output observed with the
maximum fueling rate possible at a given speed.
Nonmethane hydrocarbons means the sum of all hydrocarbon species
measured by a FID except methane, expressed with an assumed mass 13.876
grams per mole of carbon atoms.
Nonroad means relating to nonroad engines.
Nonroad engine has the meaning given in Sec. 89.2 of this chapter.
In general this means all internal combustion engines except motor
vehicle engines, stationary engines, or engines used solely for
competition.
Oxides of nitrogen means compounds containing only nitrogen and
oxygen. Oxides of nitrogen are expressed quantitatively as if the NO is
in the form of NO2 (assume a molecular weight for all oxides
of nitrogen equivalent to that of NO2). This correction is
included in the equations specified for calculating NOX
emissions.
Oxygenated fuel means a fuel that is comprised of oxygen-containing
compound, such as ethanol or methanol. Generally, testing engines that
use oxygenated fuels requires the use of the sampling methods in
subpart I of this part. However, you should read the standard-setting
part and subpart I of this part to determine which sampling methods to
use.
Precision means two times the coefficient of variance of multiple
measurements, except where specified otherwise.
Revoking a certificate of conformity means discontinuing the
certificate for an engine family. If we revoke a certificate, you must
apply for a new certificate before continuing to introduce into
commerce the affected engines. This does not apply to engines you no
longer possess.
Scheduled maintenance means maintenance (i.e., adjusting,
repairing, removing, disassembling, cleaning, or replacing components
or systems) that is periodically needed to keep a part from failing or
malfunctioning. It also may mean actions you expect are necessary to
correct an overt indication of failure or malfunction for which
periodic maintenance is not appropriate.
Span means to adjust an instrument so that it gives a proper
response to a calibration standard that represents between 75 and 100
percent of the maximum value in the instrument range (e.g. a span gas).
Spark-ignition means relating to a gasoline-fueled engine or other
engines with a spark plug (or other sparking device) and with operating
characteristics significantly similar to the theoretical Otto
combustion cycle. Spark-ignition engines usually use a throttle to
regulate intake air flow to control power during normal operation.
Standard-setting part means the part in the Code of Federal
Regulations that defines emission standards for a particular engine
(see Sec. 1065.1(a)).
Stoichiometry means the proportion of a mixture of air and fuel
such that the fuel is fully oxidized with no remaining oxygen. For
example, stoichiometric combustion in gasoline engines typically occurs
at an air-fuel mass ratio of about 14.7.
Suspending a certificate of conformity means temporarily
discontinuing the certificate for an engine family. If we suspend a
certificate, you may not sell engines from that engine family unless we
reinstate the certificate or approve a new one.
Test engine means an engine in a test sample.
Test sample means the collection of engines selected from the
population of an engine family for emission testing.
Total Hydrocarbon (THC) means the sum of all hydrocarbon species
measured by an FID, expressed with an assumed mass 13.876 grams per
mole of carbon atoms.
Total Hydrocarbon Equivalent means the sum of the carbon mass
contributions of non-oxygenated hydrocarbons, alcohols and aldehydes,
or other organic compounds that are measured separately as contained in
a gas sample, expressed as petroleum-fueled engine hydrocarbons. The
hydrogen-to-carbon ratio of the equivalent hydrocarbon is 1.85:1.
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
Wide-open throttle means maximum throttle opening for throttled
engines. Unless this is specified at a given speed, it refers to
maximum throttle opening at maximum speed. For electronically
controlled or other engines with multiple possible fueling rates, wide-
open throttle also means the maximum fueling rate at maximum throttle
opening under test conditions.
Zero means to adjust an instrument so that it gives a proper
response to a blank calibration standard (e.g. zero-grade air).
Sec. 1065.1005 Symbols, acronyms, and abbreviations.
The following symbols, acronyms, and abbreviations apply to this
part:
[deg]
degrees.
'' inches.
ASTM American Society for Testing and Materials.
C Celsius.
cc cubic centimeters.
CFR Code of Federal Regulations.
CFV critical-flow venturi.
CI compression-ignition.
CLD chemiluminescent detector.
CO carbon monoxide.
CO2 carbon dioxide.
CVS constant-volume sampler.
DF deterioration factor.
F Fahrenheit.
EFC electronic flow control.
EPA Environmental Protection Agency.
ft feet.
FID flame ionization detector.
g/kW-hr grams per kilowatt-hour.
g/liter grams per liter.
g/m\3\ grams per cubic meter.
Hz hertz.
IBP initial boiling point.
ISO International Organization for Standardization.
kPa kilopascal.
lbs. pounds.
LPG liquefied petroleum gas.
m meters.
ml milliliters.
mm Hg millimeters of mercury.
NDIR nondispersive infrared.
NIST National Institute for Standards and Testing.
NMHC nonmethane hydrocarbons.
NMHCE nonmethane hydrocarbon equivalent.
NO nitric oxide.
NO2 nitrogen dioxide.
NOX oxides of nitrogen (NO and NO2).
O2 oxygen.
PDP positive-displacement pump.
ppm parts per million.
ppmC parts per million carbon.
RMS root-mean square.
rpm revolutions per minute.
sec seconds.
SI spark-ignition.
THC total hydrocarbon.
THCE total hydrocarbon equivalent.
U.S.C. United States Code.
Sec. 1065.1010 Reference materials.
We have incorporated by reference the documents listed in this
section. The Director of the Federal Register approved the
incorporation by reference as prescribed in 5 U.S.C. 552(a) and 1 CFR
part 51. Anyone may inspect copies at the U.S. EPA, Air and Radiation
Docket and Information Center, 1301 Constitution Ave., NW., Room B102,
EPA West Building, Washington, DC 20460 or the Office of the Federal
Register, 800 N. Capitol St., NW., 7th Floor, Suite 700, Washington,
DC.
(a) ASTM material. Table 1 of Sec. 1065.1010 lists material from
the American Society for Testing and
[[Page 68427]]
Materials that we have incorporated by reference. The first column
lists the number and name of the material. The second column lists the
sections of this part where we reference it. Anyone may purchase copies
of these materials from the American Society for Testing and Materials,
100 Barr Harbor Dr., West Conshohocken, PA 19428. Table 1 follows:
Table 1 of Sec. 1065.1010.--ASTM Materials
------------------------------------------------------------------------
Part 1065
Document number and name reference
------------------------------------------------------------------------
ASTM D 86-01, Standard Test Method for Distillation of 1065.210
Petroleum Products at Atmospheric Pressure.............
---------------------------------------------------------
ASTM D 323-99a, Standard Test Method for Vapor Pressure 1065.210
of Petroleum Products (Reid Method)....................
---------------------------------------------------------
ASTM D 1266-98, Standard Test Method for Sulfur in 1065.210
Petroleum Products (Lamp Method).......................
---------------------------------------------------------
ASTM D 1319-02, Standard Test Method for Hydrocarbon 1065.210
Types in Liquid Petroleum Products by Fluorescent
Indicator Adsorption...................................
---------------------------------------------------------
ASTM D 1267-02, Standard Test Method for Gage Vapor 1065.220
Pressure of Liquefied Petroleum (LP) Gases (LP-Gas
Method)................................................
---------------------------------------------------------
ASTM D 1837-02, Standard Test Method for Volatility of 1065.220
Liquefied Petroleum (LP) Gases.........................
---------------------------------------------------------
ASTM D 1838-91 (Reapproved 2001), Standard Test Method 1065.220
for Copper Strip Corrosion by Liquefied Petroleum (LP)
Gases..................................................
---------------------------------------------------------
ASTM D 1945-96 (Reapproved 2001), Standard Test Method 1065.215
for Analysis of Natural Gas by Gas Chromatography......
---------------------------------------------------------
ASTM D 2158-02, Standard Test Method for Residues in 1065.220
Liquefied Petroleum (LP) Gases.........................
---------------------------------------------------------
ASTM D 2163-91 (Reapproved 1996), Standard Test Method 1065.220
for Analysis of Liquefied Petroleum (LP) Gases and
Propene Concentrates by Gas Chromatography.............
---------------------------------------------------------
ASTM D 2598-02, Standard Practice for Calculation of 1065.220
Certain Physical Properties of Liquefied Petroleum (LP)
Gases from Compositional Analysis......................
---------------------------------------------------------
ASTM D 2713-91 (Reapproved 2001), Standard Test Method 1065.220
for Dryness of Propane (Valve Freeze Method)...........
---------------------------------------------------------
ASTM D 2784-98, Standard Test Method for Sulfur in 1065.220
Liquefied Petroleum Gases (Oxy-Hydrogen Burner or Lamp)
---------------------------------------------------------
ASTM D 3231-02, Standard Test Method for Phosphorus in 1065.210
Gasoline...............................................
---------------------------------------------------------
ASTM D 3237-97, Standard Test Method for Lead in 1065.210
Gasoline By Atomic Absorption Spectroscopy.............
------------------------------------------------------------------------
(b) ISO material. Table 2 of Sec. 1065.1010 lists material from
the International Organization for Standardization that we have
incorporated by reference. The first column lists the number and name
of the material. The second column lists the section of this part where
we reference it. Anyone may purchase copies of these materials from the
International Organization for Standardization, Case Postale 56, CH-
1211 Geneva 20, Switzerland. Table 2 follows:
Table 2 of Sec. 1065.1010.--ISO Materials
------------------------------------------------------------------------
Document number and name Part 1065 reference
------------------------------------------------------------------------
ISO 8178-1, Reciprocating internal 1065.130, 1065.135,
combustion engines--Exhaust emission 1065.140, 1065.155.
measurement--Part 1: Test-bed measurement
of gaseous and particulate exhaust
emissions, 1996.
------------------------------------------------------------------------
Sec. 1065.1015 Confidential information.
(a) Clearly show what you consider confidential by marking,
circling, bracketing, stamping, or some other method. We will store
your confidential information as described in 40 CFR part 2. Also, we
will disclose it only as specified in 40 CFR part 2.
(b) If you send us a second copy without the confidential
information, we will assume it contains nothing confidential whenever
we need to release information from it.
(c) If you send us information without claiming it is confidential,
we may make it available to the public without further notice to you,
as described in Sec. 2.204 of this chapter.
PART 1068--GENERAL COMPLIANCE PROVISIONS FOR NONROAD PROGRAMS
Subpart A--Applicability and Miscellaneous Provisions
Sec.
1068.1 Does this part apply to me?
1068.5 How must manufacturers apply good engineering judgment?
1068.10 How do I request EPA to keep my information confidential
1068.15 Who is authorized to represent the Agency?
1068.20 May EPA enter my facilities for inspections?
1068.25 What information must I give to EPA?
1068.30 What definitions apply to this part?
1068.35 What symbols, acronyms, and abbreviations does this part
use?
[[Page 68428]]
Subpart B--Prohibited Actions and Related Requirements
1068.101 What general actions does this regulation prohibit?
1068.105 What other provisions apply to me specifically if I
manufacture equipment needing certified engines?
1068.110 What other provisions apply to engines in service?
1068.115 When must manufacturers honor emission-related warranty
claims?
1068.120 What requirements must I follow to rebuild engines?
1068.125 What happens if I violate the regulations?
Subpart C--Exemptions and Exclusions
1068.201 Does EPA exempt or exclude any engines from the prohibited
acts?
1068.210 What are the provisions for exempting test engines?
1068.215 What are the provisions for exempting manufacturer-owned
engines?
1068.220 What are the provisions for exempting display engines?
1068.225 What are the provisions for exempting engines for national
security?
1068.230 What are the provisions for exempting engines for export?
1068.235 What are the provisions for exempting engines used solely
for competition?
1068.240 What are the provisions for exempting new replacement
engines?
1068.245 What temporary provisions address hardship due to unusual
circumstances?
1068.250 What are the provisions for extending compliance deadlines
for small-volume manufacturers under hardship?
1068.255 What are the provisions for exempting engines for hardship
for equipment manufacturers and secondary engine manufacturers?
Subpart D--Imports
1068.301 Does this subpart apply to me?
1068.305 How do I get an exemption or exclusion for imported
engines?
1068.310 What are the exclusions for imported engines?
1068.315 What are the permanent exemptions for imported engines?
1068.320 How must I label an imported engine with a permanent
exemption?
1068.325 What are the temporary exemptions for imported engines?
1068.330 How do I import engines to modify for other applications?
1068.335 What are the penalties for violations?
Subpart E--Selective Enforcement Auditing
11068.401 What is a selective enforcement audit?
1068.405 What is in a test order?
1068.410 How must I select and prepare my engines?
1068.415 How do I test my engines?
1068.420 How do I know when my engine family fails an SEA?
1068.425 What happens if one of my production-line engines exceeds
the emission standards?
1068.430 What happens if an engine family fails an SEA?
1068.435 May I sell engines from an engine family with a suspended
certificate of conformity?
1068.440 How do I ask EPA to reinstate my suspended certificate?
1068.445 When may EPA revoke my certificate under this subpart and
how may I sell these engines again?
1068.450 What records must I send to EPA?
1068.455 What records must I keep?
Appendix A to Subpart E of Part 1068-Plans for Selective Enforcement
Auditing
Subpart F--Reporting Defects and Recalling Engines
1068.501 How do I report engine defects?
1068.505 How does the recall program work?
1068.510 How do I prepare and apply my remedial plan?
1068.515 How do I mark or label repaired engines?
1068.520 How do I notify affected owners?
1068.525 What records must I send to EPA?
1068.530 What records must I keep?
1068.535 How can I do a voluntary recall for emission-related
problems?
1068.540 What terms do I need to know for this subpart?
Subpart G--Hearings
1068.601 What are the procedures for hearings?
Appendix I to Part 1068--Emission-Related Components
Appendix II to Part 1068--Emission-Related Parameters and
Specifications
Authority: 42 U.S.C. 7401-7671(q).
Subpart A--Applicability and Miscellaneous Provisions
Sec. 1068.1 Does this part apply to me?
(a) The provisions of this part apply to everyone with respect to
the following engines or to equipment using the following engines
(including owners, operators, parts manufacturers, and persons
performing maintenance):
(1) Large nonroad spark-ignition engines we regulate under 40 CFR
part 1048.
(2) Recreational SI engines and vehicles that we regulate under 40
CFR part 1051 (such as snowmobiles and off-highway motorcycles).
(b) This part does not apply to any of the following engine or
vehicle categories:
(1) Light-duty motor vehicles (see 40 CFR part 86).
(2) Heavy-duty motor vehicles and motor vehicle engines (see 40 CFR
part 86).
(3) Aircraft engines (see 40 CFR part 87).
(4) Locomotive engines (see 40 CFR part 92).
(5) Land-based nonroad diesel engines (see 40 CFR part 89).
(6) Marine diesel engines (see 40 CFR parts 89 and 94)
(7) Marine outboard and personal watercraft engines (see 40 CFR
part 91).
(8) Small nonroad spark-ignition engines (see 40 CFR part 90).
(c) For equipment subject to this part and regulated under
equipment-based standards, interpret the term ``engine'' in this part
to include equipment (see Sec. 1068.30).
(d) Paragraph (a)(1) of this section identifies the parts of the
CFR that define emission standards and other requirements for
particular types of engines and vehicles. This part 1068 refers to each
these other parts generically as the ``standard-setting part.'' For
example, 40 CFR part 1051 is always the standard-setting part for
snowmobiles. Follow the provisions of the standard-setting part if they
are different than any of the provisions in this part.
Sec. 1068.5 How must manufacturers apply good engineering judgment?
(a) You must use good engineering judgment for decisions related to
any requirements under this chapter. This includes your applications
for certification, any testing you do to show that your production-line
or in-use engines comply with requirements that apply to them, and how
you select, categorize, determine, and apply these requirements.
(b) If we send you a written request, you must give us a written
description of the engineering judgment in question. Respond within 15
working days of receiving our request unless we allow more time.
(c) We may reject your decision if it is not based on good
engineering judgment or is otherwise inconsistent with the requirements
that apply, based on the following provisions:
(1) We may suspend, revoke, or void a certificate of conformity if
we determine you deliberately used incorrect information or overlooked
important information, that you did not decide in good faith, or that
your decision was not rational.
(2) If we believe a different decision would better reflect good
engineering judgment, but none of the provisions of paragraph (c)(1) of
this section apply, we will tell you of our concern (and its basis).
You will have 30 days to respond to our concerns, or more time if we
agree that you need it to generate more information. After considering
your information, we will give you a final ruling. If we conclude that
you did not use good engineering judgment, we may reject your decision
and apply the new ruling to similar situations as soon as possible.
(d) We will tell you in writing of the conclusions we reach under
paragraph
[[Page 68429]]
(c) of this section and explain our reasons for them.
(e) If you disagree with our conclusions, you may file a request
for a hearing with the Designated Officer as described in subpart F of
this part. In your request, specify your objections, include data or
supporting analysis, and get your authorized representative's
signature. If we agree that your request raises a substantial factual
issue, we will hold the hearing according to subpart F of this part.
Sec. 1068.10 How do I request EPA to keep my information confidential
(a) Clearly identify any information you consider confidential by
marking, circling, bracketing, stamping, or some other method. We will
store your confidential information as described in 40 CFR part 2.
Also, we will disclose it only as specified in 40 CFR part 2. This
procedure applies equally to the Environmental Appeals Board.
(b) If you send us a second copy without the confidential
information, we will assume it contains nothing confidential whenever
we need to release information from it.
(c) If you send us information without claiming it is confidential,
we may make it available to the public without further notice to you,
as described in Sec. 2.204 of this chapter.
Sec. 1068.15 Who is authorized to represent the Agency?
(a) The Administrator of the Environmental Protection Agency or any
official to whom the Administrator has delegated specific authority may
represent the Agency. For more information, ask for a copy of the
relevant sections of the EPA Delegation Manual from the Designated
Officer.
(b) The regulations in this part and in the standard-setting part
have specific requirements describing how to get EPA approval before
you take specific actions. These regulations also allow us to waive
some specific requirements. For provisions or flexibilities that we
address frequently, we may choose to provide detailed guidance in
supplemental compliance instructions for manufacturers. Such
instructions will generally state how they relate to the need for pre-
approval. Unless we explicitly state so, you should not consider full
compliance with the instructions to be equivalent to EPA approval.
Sec. 1068.20 May EPA enter my facilities for inspections?
(a) We may inspect your engines, testing, manufacturing processes,
engine storage facilities (including port facilities for imported
engines or other relevant facilities), or records, as authorized by the
Act, to enforce the provisions of this chapter. Inspectors will have
authorizing credentials and will limit inspections to reasonable
times--usually, normal operating hours.
(b) If we come to inspect, we may or may not have a warrant or
court order.
(1) If we do not have a warrant or court order, you may deny us
entry.
(2) If we have a warrant or court order, you must allow us to enter
the facility and carry out the activities it describes.
(c) We may seek a warrant or court order authorizing an inspection
described in this section, whether or not we first tried to get your
permission to inspect.
(d) We may select any facility to do any of the following:
(1) Inspect and monitor any aspect of engine manufacturing,
assembly, storage, or other procedures, and any facilities where you do
them.
(2) Inspect and monitor any aspect of engine test procedures or
test-related activities, including test engine selection, preparation,
service accumulation, emission duty cycles, and maintenance and
verification of your test equipment's calibration.
(3) Inspect and copy records or documents related to assembling,
storing, selecting, and testing an engine.
(4) Inspect and photograph any part or aspect of engines and
components you use for assembly.
(e) You must give us reasonable help without charge during an
inspection authorized by the Act. For example, you may need to help us
arrange an inspection with the facility's managers, including clerical
support, copying, and translation. You may also need to show us how the
facility operates and answer other questions. If we ask in writing to
see a particular employee at the inspection, you must ensure that he or
she is present (legal counsel may accompany the employee).
(f) If you have facilities in other countries, we expect you to
locate them in places where local law does not keep us from inspecting
as described in this section. We will not try to inspect if we learn
that local law prohibits it, but we may suspend your certificate if we
are not allowed to inspect.
Sec. 1068.25 What information must I give to EPA?
If you are subject to the requirements of this part, we may require
you to give us information to evaluate your compliance with any
regulations that apply, as authorized by the Act. This includes the
following things:
(a) You must provide the information we require in this chapter.
(b) You must establish and maintain records, perform tests, make
reports and provide additional information that we may reasonably
require under section 208 of the Act. This also applies to engines we
exempt from emission standards.
Sec. 1068.30 What definitions apply to this part?
The following definitions apply to this part. The definitions apply
to all subparts unless we note otherwise. All undefined terms have the
meaning the Act gives to them. The definitions follow:
Act means the Clean Air Act, as amended, 42 U.S.C. 7401 et seq.
Aircraft means any vehicle capable of sustained air travel above
treetop heights.
Certificate holder means a manufacturer (including importers) with
a valid certificate of conformity for at least one engine family in a
given calendar year.
Designated Officer means the Manager of the Engine Programs Group
(6405-J), U.S. Environmental Protection Agency, 1200 Pennsylvania Ave.,
Washington, DC 20460.
Emission-related defect means a defect in design, materials or
workmanship (in an emission control device or vehicle component or
system) that affects an emission-related component, parameter, or
specification that is identified in Appendix I or Appendix II of this
part.
Engine means an engine to which this part applies. For equipment
subject to this part and regulated under equipment-based standards, the
term engine in this part shall be interpreted to include equipment.
Engine-based means having emission standards related to
measurements using an engine dynamometer, in units of grams of
pollutant per kilowatt-hour.
Engine manufacturer means the manufacturer that is subject to the
certification requirements of the standard-setting part. For vehicles/
equipment subject to this part and regulated under vehicle/equipment-
based standards, the term engine manufacturer in this part includes
vehicles/equipment manufacturers.
Equipment-based means having emission standards related to
measurements from an engine installed in a vehicle using a chassis
dynamometer, in units of grams of pollutant per kilometer.
Equipment manufacturer means any company producing a piece of
equipment (such as a vehicle) for sale or use in the United States.
Manufacturer has the meaning given in section 216(1) of the Act. In
general,
[[Page 68430]]
this term includes any person who manufactures an engine or vehicle for
sale in the United States or otherwise introduces a new engine or
vehicle into commerce in the United States. This includes importers
that import new engines or new equipment into the United States for
resale. It also includes secondary engine manufacturers.
New has the meaning we give it in the standard-setting part.
Nonroad engine means:
(1) Except as discussed in paragraph (2) of this definition, a
nonroad engine is any internal combustion engine:
(i) In or on a piece of equipment that is self-propelled or serves
a dual purpose by both propelling itself and performing another
function (such as garden tractors, off-highway mobile cranes and
bulldozers); or
(ii) In or on a piece of equipment that is intended to be propelled
while performing its function (such as lawnmowers and string trimmers);
or
(iii) That, by itself or in or on a piece of equipment, is portable
or transportable, meaning designed to be and capable of being carried
or moved from one location to another. Indicia of transportability
include, but are not limited to, wheels, skids, carrying handles,
dolly, trailer, or platform.
(2) An internal combustion engine is not a nonroad engine if:
(i) The engine is used to propel a motor vehicle or a vehicle used
solely for competition, or is subject to standards promulgated under
section 202 of the Act; or
(ii) The engine is regulated by a federal New Source Performance
Standard promulgated under section 111 of the Act; or
(iii) The engine otherwise included in paragraph (1)(iii) of this
definition remains or will remain at a location for more than 12
consecutive months or a shorter period of time for an engine located at
a seasonal source. A location is any single site at a building,
structure, facility, or installation. Any engine (or engines) that
replaces an engine at a location and that is intended to perform the
same or similar function as the engine replaced will be included in
calculating the consecutive time period. An engine located at a
seasonal source is an engine that remains at a seasonal source during
the full annual operating period of the seasonal source. A seasonal
source is a stationary source that remains in a single location on a
permanent basis (i.e., at least two years) and that operates at that
single location approximately three months (or more) each year. This
paragraph (2)(iii) does not apply to an engine after the engine is
removed from the location.
Operating hours means:
(1) For engine storage areas or facilities, times during which
people other than custodians and security personnel are at work near,
and can access, a storage area or facility.
(2) For other areas or facilities, times during which an assembly
line operates or any of the following activities occurs:
(i) Testing, maintenance, or service accumulation.
(ii) Production or compilation of records.
(iii) Certification testing.
(iv) Translation of designs from the test stage to the production
stage.
(v) Engine manufacture or assembly.
Piece of equipment means any vehicle, vessel, locomotive, aircraft,
or other type of equipment using engines to which this part applies.
Placed into service means used for its intended purpose.
Reasonable technical basis means information that would lead a
person familiar with engine design and function to reasonably believe a
conclusion, related to compliance with the requirements of this part.
For example, it would be reasonable to believe that parts performing
the same function as the original parts (and to the same degree) would
control emissions to the same degree as the original parts.
Standard-setting part means the part in the Code of Federal
Regulations that defines emission standards for a particular engine
(see Sec. 1068.1(a)). For example, the standard-setting part for non-
recreational spark-ignition engines over 19 kW is part 1048 of this
chapter.
Ultimate purchaser means the first person who in good faith buys a
new engine for purposes other than resale.
United States means the States, the District of Columbia, the
Commonwealth of Puerto Rico, the Commonwealth of the Northern Mariana
Islands, Guam, American Samoa, the U.S. Virgin Islands, and the Trust
Territory of the Pacific Islands.
We (us, our) means the Administrator of the Environmental
Protection Agency and any authorized representatives.
Sec. 1068.35 What symbols, acronyms, and abbreviations does this part
use?
The following symbols, acronyms, and abbreviations apply to this
part:
$ U.S. dollars.
CFR Code of Federal Regulations.
EPA Environmental Protection Agency.
U.S. United States.
U.S.C. United States Code.
Subpart B--Prohibited Actions and Related Requirements
Sec. 1068.101 What general actions does this regulation prohibit?
This section specifies actions that are prohibited and the maximum
civil penalties that we can assess for each violation. The maximum
penalty values listed in paragraphs (a) and (b) of this section are
shown for calendar year 2002. As described in paragraph (e) of this
section, maximum penalty limits for later years are set forth in 40 CFR
part 19.
(a) The following prohibitions and requirements apply to
manufacturers of new engines and manufacturers of equipment containing
these engines, except as described in subparts C and D of this part:
(1) You may not sell, offer for sale, or introduce or deliver into
commerce in the United States or import into the United States any new
engine or equipment after emission standards take effect for that
engine or equipment, unless it has a valid certificate of conformity
for its model year and the required label or tag. You also may not take
any of the actions listed in the previous sentence with respect to any
equipment containing an engine subject to this part's provisions,
unless the engine has a valid certificate of conformity for its model
year and the required engine label or tag. This requirement also covers
new engines you produce to replace an older engine in a piece of
equipment, unless the engine qualifies for the replacement-engine
exemption in Sec. 1068.240. We may assess a civil penalty up to
$31,500 for each engine in violation.
(2) This chapter requires you to record certain types of
information to show that you meet our standards. You must comply with
these requirements to make and maintain required records (including
those described in Sec. 1068.501). You may not deny us access to or
copying of your records if we have the authority to see or copy them.
Also, you must give us the required reports or information without
delay. Failure to comply with the requirements of this paragraph is
prohibited. We may assess a civil penalty up to $31,500 for each day in
violation.
(3) You may not keep us from entering your facility to test engines
or inspect if we are authorized to do so. Also, you must perform the
tests we require (or have the tests done for you). Failure to perform
this testing is prohibited. We may assess a civil penalty up to $31,500
for each day in violation.
[[Page 68431]]
(b) The following prohibitions apply to everyone with respect to
the engines to which this part applies:
(1) You may not remove or disable a device or element of design
that may affect an engine's emission levels. This restriction applies
before and after the engine is placed in service. Section 1068.120
describes how this applies to rebuilding engines. For a manufacturer or
dealer, we may assess a civil penalty up to $31,500 for each engine in
violation. For anyone else, we may assess a civil penalty up to $3,150
for each engine in violation. This does not apply in any of the
following situations:
(i) You need to repair an engine and you restore it to proper
functioning when the repair is complete.
(ii) You need to modify an engine to respond to a temporary
emergency and you restore it to proper functioning as soon as possible.
(iii) You modify a new engine that another manufacturer has already
certified to meet emission standards, intending to recertify it under
your own engine family. In this case you must tell the original
manufacturer not to include the modified engines in the original engine
family.
(2) You may not knowingly manufacture, sell, offer to sell, or
install, an engine part if one of its main effects is to bypass,
impair, defeat, or disable the engine's control of emissions. We may
assess a civil penalty up to $3,150 for each part in violation.
(3) For an engine that is excluded from any requirements of this
chapter because it is a stationary engine, you may not move it or
install it in any mobile equipment, except as allowed by the provisions
of this chapter. You may not circumvent or attempt to circumvent the
residence-time requirements of paragraph (2)(iii) of the nonroad engine
definition in Sec. 1068.30. We may assess a civil penalty up to
$31,500 for each day in violation.
(4) For an uncertified engine or piece of equipment that is
excluded or exempted from any requirements of this chapter because it
is to be used solely for competition, you may not use it in a manner
that is inconsistent with use solely for competition. We may assess a
civil penalty up to $31,500 for each day in violation.
(5) You may not import an uncertified engine or piece of equipment
if it is defined to be new in the standard-setting part, and it would
have been subject to standards had it been built in the United States.
We may assess a civil penalty up to $31,500 for each day in violation.
Note the following:
(i) The definition of new is broad for imported engines;
uncertified engines and equipment (including used engines and
equipment) are generally considered to be new when imported.
(ii) Engines that were originally manufactured before applicable
EPA standards were in effect are generally not subject to emission
standards.
(c) Exemptions from these prohibitions are described in subparts C
and D of this part.
(d) The standard-setting parts describe more requirements and
prohibitions that apply to manufacturers (including importers) and
others under this chapter.
(e) The maximum penalty values listed in paragraphs (a) and (b) of
this section are shown for calendar year 2002. Maximum penalty limits
for later years may be adjusted based on the Consumer Price Index. The
specific regulatory provisions for changing the maximum penalties,
published in 40 CFR part 19, reference the applicable U.S. Code
citation on which the prohibited action is based. The following table
is shown here for informational purposes:
Table 1 of Sec. 1068.101.--Legal Citation for Specific Prohibitions for Determining Maximum Penalty Amounts
----------------------------------------------------------------------------------------------------------------
Part 1068 regulatory citation of General description of U.S. Code citation for Clean Air Act
prohibited action prohibition authority
----------------------------------------------------------------------------------------------------------------
Sec. 1068.101(a)(1)................ Introduction into commerce of 42 U.S.C. 7522(a)(1)
an uncertified product.
--------------------------------------
Sec. 1068.101(a)(1)................ Failure to provide 42 U.S.C. 7522(a)(2)
information.
--------------------------------------
Sec. 1068.101(a)(3)................ Denying access to facilities. 42 U.S.C. 7522(a)(2)
--------------------------------------
Sec. 1068.101(b)(1)................ Tampering with emission 42 U.S.C. 7522(a)(3)
controls by a manufacturer
or dealer.
Tampering with emission
controls by someone other
than a manufacturer or
dealer.
--------------------------------------
Sec. 1068.101(b)(2)................ Sale or use of a defeat 42 U.S.C. 7522(a)(3)
device.
--------------------------------------
Sec. 1068.101(b)(3)................ Mobile use of a stationary 42 U.S.C. 7522(a)(1)
engine.
--------------------------------------
Sec. 1068.101(b)(4)................ Noncompetitive use of an 42 U.S.C. 7522(a)(1)
uncertified engine that is
exempted for competition.
--------------------------------------
Sec. 1068.101(b)(5)................ Importation of an uncertified 42 U.S.C. 7522(a)(1)
product.
----------------------------------------------------------------------------------------------------------------
Sec. 1068.105 What other provisions apply to me specifically if I
manufacture equipment needing certified engines?
(a) Transitioning to new standards. You may use up your normal
inventory of engines not certified to new emission standards if they
were built before the date of the new standards. However, stockpiling
these engines violates Sec. 1068.101(a)(1).
(b) Installing engines. You must follow the engine manufacturer's
emission-related installation instructions. For example, you may need
to constrain where you place an exhaust aftertreatment device or
integrate into your equipment models a device for sending visual or
audible signals to the operator. Not meeting the manufacturer's
emission-related installation instructions is a violation of Sec.
1068.101(b)(1).
(c) Attaching a duplicate label. If you obscure the engine's label,
you must do three things to avoid violating Sec. 1068.101(a)(1):
(1) Permanently attach to your equipment a duplicate label. Secure
it to a part needed for normal operation and not normally requiring
replacement.
[[Page 68432]]
(2) Make sure your label is identical to the engine label. You may
make the label yourself or get it from the engine manufacturer.
(3) Make sure an average person can easily read it.
(d) Producing nonroad equipment certified to highway emission
standards. You may produce nonroad equipment from complete or
incomplete motor vehicles with the motor vehicle engine if you meet
three criteria:
(1) The engine or vehicle is certified to 40 CFR part 86.
(2) The engine is not adjusted outside the manufacturer's
specifications.
(3) The engine or vehicle is not modified in any way that may
affect its emission control. This applies to evaporative emission
controls, but not refueling emission controls.
Sec. 1068.110 What other provisions apply to engines in service?
(a) Aftermarket parts and service. As the engine manufacturer, you
may not require anyone to use your parts or service to maintain or
repair an engine, unless we approve this in your application for
certification. It is a violation of the Act for anyone to manufacture
an engine or vehicle part if one of its main effects is to reduce the
effectiveness of the emission controls. See Sec. 1068.101(b)(2).
(b) Certifying aftermarket parts. As the manufacturer or rebuilder
of an aftermarket engine part, you may--but are not required to--
certify according to Sec. 85.2114 of this chapter that using the part
will not cause engines to fail to meet emission standards. Whether you
certify or not, however, you must keep any information showing how your
parts or service affect emissions.
(c) Compliance with standards. We may test engines or equipment to
investigate compliance with emission standards. We may also require the
manufacturer to do this testing.
(d) Defeat devices. We may test engines or equipment to investigate
potential defeat devices. We may also require the manufacturer to do
this testing. If we choose to investigate one of your designs, we may
require you to show us that it does not have a defeat device. To do
this, you may have to share with us information regarding test
programs, engineering evaluations, design specifications, calibrations,
on-board computer algorithms, and design strategies. It is a violation
of the Act for anyone to make, install or use defeat devices. See Sec.
1068.101(b)(2) and the standard-setting part.
(e) Warranty and maintenance. Owners may make warranty claims
against the manufacturer for emission-related parts, as described in
Sec. 1068.115. This generally includes any emission-related engine
parts that were not in common use before we have adopted emission
standards. In general, we consider replacement or repair of any other
components to be the owner's responsibility. The warranty period begins
when the engine is first placed into service. See the standard-setting
part for specific requirements. It is a violation of the Act for anyone
to disable emission controls. See Sec. 1068.101(b)(1) and the
standard-setting part.
Sec. 1068.115 When must manufacturers honor emission-related warranty
claims?
Section 207(a) of the Clean Air Act (42 U.S.C. 7541(a)) requires
certifying manufacturers to warrant to purchasers that their engines
are designed, built, and equipped to conform at the time of sale to the
applicable regulations for their full useful life, including a warranty
that the engines are free from defects in materials and workmanship
that would cause an engine to fail to conform to the applicable
regulations during the specified warranty period. This section codifies
the warranty requirements of section 207(a) without intending to limit
these requirements.
(a) As a certifying manufacturer, you may deny warranty claims for
failures that have been caused by the owner's or operator's improper
maintenance or use. For example, you would not need to honor warranty
claims for failures that have been directly caused by the operator's
abuse of an engine or the operator's use of the engine in a manner for
which it was not designed, and are not attributable to you in any way.
(b) As a certifying manufacturer, you may not deny emission-related
warranty claims based on any of the following:
(1) Maintenance or other service you or your authorized facilities
performed.
(2) Engine repair work that an operator performed to correct an
unsafe, emergency condition attributable to you, as long as the
operator tries to restore the engine to its proper configuration as
soon as possible.
(3) Any action or inaction by the operator unrelated to the
warranty claim.
(4) Maintenance that was performed more frequently than you
specify.
(5) Anything that is your fault or responsibility.
(6) The use of any fuel that is commonly available where the engine
operates, unless your written maintenance instructions state that this
fuel would harm the engine's emission control system and operators can
readily find the proper fuel.
Sec. 1068.120 What requirements must I follow to rebuild engines?
(a) This section describes the steps to take when rebuilding
engines to avoid violating the tampering prohibition in Sec.
1068.101(b)(1). These requirements apply to anyone rebuilding an engine
subject to this part, but the recordkeeping requirements in paragraphs
(j) and (k) of this section apply only to businesses.
(b) The term ``rebuilding'' refers to a rebuild of an engine or
engine system, including a major overhaul in which you replace the
engine's pistons or power assemblies or make other changes that
significantly increase the service life of the engine. It also includes
replacing or rebuilding an engine's turbocharger or aftercooler or the
engine's systems for fuel metering or electronic control so that it
significantly increases the service life of the engine. For these
provisions, rebuilding may or may not involve removing the engine from
the equipment. Rebuilding does not normally include the following:
(1) Scheduled emission-related maintenance that the standard-
setting part allows during the useful life period (such as replacing
fuel injectors).
(2) Unscheduled maintenance that occurs commonly within the useful
life period. For example, replacing a water pump is not rebuilding.
(c) For maintenance or service that is not rebuilding, you may not
make changes that might increase emissions, but you do not need to keep
any records.
(d) If you rebuild an engine or engine system, you must have a
reasonable technical basis for knowing that the rebuilt engine has the
same emissions performance as the engine in its certified
configuration. Identify the model year of the resulting engine
configuration. You have a reasonable basis if you meet two main
conditions:
(1) Install parts--new, used, or rebuilt--so a person familiar with
engine design and function would reasonably believe that the engine
with those parts will control emissions to the same degree as with the
original parts. For example, it would be reasonable to believe that
parts performing the same function as the original parts (and to the
same degree) would control emissions to the same degree as the original
parts.
(2) Adjust parameters or change design elements only according to
the original engine manufacturer's instructions. Or, if you differ from
these instructions, you must have data or some other technical basis to
show you should not expect in-use emissions to increase.
[[Page 68433]]
(e) If the rebuilt engine remains installed or is reinstalled in
the same piece of equipment, you must rebuild it to the original
configuration or another certified configuration of the same or later
model year.
(f) If the rebuilt engine replaces another engine in a piece of
equipment, you must rebuild it to a certified configuration that equals
the emissions performance of the engine you are replacing.
(g) Do not erase or reset emission-related codes or signals from
onboard monitoring systems without diagnosing and responding
appropriately to any diagnostic codes. This requirement applies
regardless of the manufacturer's reason for installing the monitoring
system and regardless of its form or interface. Clear any codes from
diagnostic systems when you return the rebuilt engine to service. Do
not disable a diagnostic signal without addressing its cause.
(h) When you rebuild an engine, check, clean, adjust, repair, or
replace all emission-related components (listed in Appendix I of this
part) as needed according to the original manufacturer's recommended
practice. In particular, replace oxygen sensors, replace the catalyst
if there is evidence of malfunction, clean gaseous fuel system
components, and replace fuel injectors (if applicable), unless you have
a reasonable technical basis for believing they do not need
replacement.
(i) If you are installing an engine that someone else has rebuilt,
check all emission-related components listed in Appendix I of this part
as needed according to the original manufacturer's recommended
practice.
(j) Keep at least the following records:
(1) Identify the hours of operation (or mileage, as appropriate) at
time of rebuild.
(2) Identify the work done on the engine or any emission-related
control components, including a listing of parts and components you
used.
(3) Describe any engine parameter adjustments.
(4) Identify any emission-related codes or signals you responded to
and reset.
(k) You must show us or send us your records if we ask for them.
Keep records for at least two years after rebuilding an engine. Keep
them in any format that allows us to readily review them.
(1) You do not need to keep information that is not reasonably
available through normal business practices. We do not expect you to
have information that you cannot reasonably access.
(2) You do not need to keep records of what other companies do.
(3) You may keep records based on engine families rather than
individual engines if that is the way you normally do business.
Sec. 1068.125 What happens if I violate the regulations?
(a) Civil penalties and injunctions. We may bring a civil action to
assess and recover civil penalties and/or enjoin and restrain
violations in the United States District Court for the district where
you allegedly violated a requirement, or the district where you live or
have your main place of business. Actions to assess civil penalties or
restrain violations of Sec. 1068.101 must be brought by and in the
name of the United States. The selected court has jurisdiction to
restrain violations and assess civil penalties.
(1) To determine the amount of a civil penalty and reach a just
conclusion, the court considers these main factors:
(i) The seriousness of your violation.
(ii) How much you benefitted or saved because of the violation.
(iii) The size of your business.
(iv) Your history of compliance with Title II of the Act.
(v) What you did to remedy the violation.
(vi) How the penalty will affect your ability to continue in
business.
(vii) Such other matters as justice may require.
(2) Subpoenas for witnesses who must attend a district court in any
district may apply to any other district.
(b) Administrative penalties. Instead of bringing a civil action,
we may assess administrative penalties if the total is less than
$250,000 against you individually. This maximum penalty may be greater
if the Administrator and the Attorney General jointly determine that is
appropriate for administrative penalty assessment, or if the limit is
adjusted under 40 CFR part 19. No court may review such a
determination. Before we assess an administrative penalty, you may ask
for a hearing (subject to 40 CFR part 22). The Administrator may
compromise or remit, with or without conditions, any administrative
penalty that may be imposed under this section.
(1) To determine the amount of an administrative penalty, we will
consider the factors described in paragraph (a)(1) of this section.
(2) An administrative order we issue under this paragraph (b)
becomes final 30 days after we issue it, unless you ask for judicial
review by that time (see paragraph (c) of this section). You may ask
for review by any of the district courts listed in paragraph (a) of
this section. Send the Administrator a copy of the filing by certified
mail.
(3) We will not pursue an administrative action for a violation if
either of the following two conditions is true:
(i) We are separately prosecuting the violation under this part.
(ii) We have issued a final order for a violation, no longer
subject to judicial review, for which you have already paid a penalty.
(c) Judicial review. If you ask a court to review a civil or
administrative penalty, we will file in the appropriate court within 30
days of your request a certified copy or certified index of the record
on which the court or the Administrator issued the order.
(1) The judge may set aside or remand any order issued under this
section only if one of the following is true:
(i) Substantial evidence does not exist in the record, taken as a
whole, to support finding a violation.
(ii) The Administrator's assessment of the penalty is an abuse of
discretion.
(2) The judge may not add civil penalties unless our penalty is an
abuse of discretion that favors you.
(d) Effect of enforcement actions on other requirements. Our
pursuit of civil or administrative penalties does not affect or limit
our authority to enforce any provisions of this chapter.
(e) Penalties. In any proceedings, the United States government may
seek to collect civil penalties assessed under this section.
(1) Once a penalty assessment is final, if you do not pay it, the
Administrator will ask the Attorney General to bring a civil action in
an appropriate district court to recover the money. We may collect
interest from the date of the final order or final judgment at rates
established by the Internal Revenue Code of 1986 (26 U.S.C.
6621(a)(2)). In this action to collect overdue penalties, the court
will not review the validity, amount, and appropriateness of the
penalty. (2) In addition, if you do not pay the full amount of a
penalty on time, you must then pay more to cover interest, enforcement
expenses (including attorney's fees and costs for collection), and a
quarterly nonpayment penalty for each quarter you do not pay. The
nonpayment penalty is 10 percent of your total penalties plus any
unpaid nonpayment penalties from previous quarters.
[[Page 68434]]
Subpart C--Exemptions and Exclusions
Sec. 1068.201 Does EPA exempt or exclude any engines from the
prohibited acts?
We may exempt new engines from the prohibited acts in subpart B of
this part under requirements described in this subpart. We may exempt
an engine already placed in service in the United States from the
prohibition in Sec. 1068.101(b)(1) if the exemption for engines used
solely for competition applies (see Sec. 1068.235). In addition, see
Sec. 1068.1 and the standard-setting parts to determine if other
engines are excluded from some or all of the regulations in this
chapter.
(a) This subpart identifies which engines qualify for exemptions
and what information we need. We may ask for more information.
(b) If you violate any of the terms, conditions, instructions, or
requirements to qualify for an exemption, we may void the exemption.
(c) If you use an exemption under this subpart, we may require you
to add a permanent label to your exempted engines. You may ask us to
approve wording on the emission label different than we specify in this
subpart if it is more appropriate for your engine.
(d) If you produce engines we exempt under this subpart, we may
require you to make and keep records, perform tests, make reports and
provide information as needed to reasonably evaluate the validity of
the exemption.
(e) If you own or operate engines we exempt under this subpart, we
may require you to provide information as needed to reasonably evaluate
the validity of the exemption.
(f) Subpart D of this part describes how we apply these exemptions
to engines you import (or intend to import).
(g) If you want to ask for an exemption or need more information,
write to the Designated Officer.
(h) You may ask us to modify the administrative requirements for
the exemptions described in this subpart. We may approve your request
if we determine that such approval is consistent with the intent of
this part. For example, waivable administrative requirements might
include some reporting requirements, but would not include any
eligibility requirements or use restrictions.
(i) If you want to take an action with respect to an exempted or
excluded engine that is prohibited by the exemption or exclusion, such
as selling it, you need to certify the engine. We will issue a
certificate of conformity if you send us an application for
certification showing that you meet all the applicable requirements
from the standard-setting part. Also, in some cases, it may be
sufficient to modify the engine as needed to make it identical to
engines already covered by a certificate. Make sure these engines have
emission control information labels that accurately describe their
status.
Sec. 1068.210 What are the provisions for exempting test engines?
(a) We may exempt engines that are not exempted under other
sections of this part that you will use for research, investigations,
studies, demonstrations, or training.
(b) Anyone may ask for a testing exemption.
(c) If you are a certificate holder, you may request an exemption
for engines you intend to include in test programs over a two-year
period.
(1) In your request, tell us the maximum number of engines involved
and describe how you will make sure exempted engines are used only for
this testing.
(2) Give us the information described in paragraph (d) of this
section if we ask for it.
(d) If you are not a certificate holder do all of the following:
(1) Show that the proposed test program has a valid purpose under
paragraph (a) of this section.
(2) Show you need an exemption to achieve the purpose of the test
program (time constraints may be a basis for needing an exemption, but
the cost of certification alone is not).
(3) Estimate the duration of the proposed test program and the
number of engines involved.
(4) Allow us to monitor the testing.
(5) Describe how you will ensure that you stay within this
exemption's purposes. Address at least the following things:
(i) The technical nature of the test.
(ii) The test site.
(iii) The duration and accumulated engine operation associated with
the test.
(iv) Ownership of the engines involved in the test.
(v) The intended final disposition of the engines.
(vi) How you will identify, record, and make available the engine
identification numbers.
(vii) The means or procedure for recording test results.
(e) If we approve your request for a testing exemption, we will
send you a letter or a memorandum for your signature describing the
basis and scope of the exemption. The exemption does not take effect
until we receive the signed letter or memorandum from you. It will also
include any necessary terms and conditions, which normally require you
to do the following:
(1) Stay within the scope of the exemption.
(2) Create and maintain adequate records that we may inspect.
(3) Add a permanent, legible label, written in block letters in
English, to a readily visible part of each exempted engine. This label
must include at least the following items:
(i) The label heading ``EMISSION CONTROL INFORMATION''.
(ii) Your corporate name and trademark.
(iii) Engine displacement, engine family identification (as
applicable), and model year of the engine; or whom to contact for
further information.
(iv) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.210
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
(4) Tell us when the test program is finished.
(5) Tell us the final disposition of the engines.
(6) Send us a written confirmation that you meet the terms and
conditions of this exemption.
Sec. 1068.215 What are the provisions for exempting manufacturer-
owned engines?
(a) You are eligible for the exemption for manufacturer-owned
engines only if you are a certificate holder.
(b) An engine may be exempt without a request if it is a
nonconforming engine under your ownership and control and you operate
it to develop products, assess production methods, or promote your
engines in the marketplace. You may not lease, sell, or use the engine
to generate revenue, either by itself or in a piece of equipment.
(c) To use this exemption, you must do three things:
(1) Establish, maintain, and keep adequately organized and indexed
information on each exempted engine, including the engine
identification number, the use of the engine on exempt status, and the
final disposition of any engine removed from exempt status.
(2) Let us access these records, as described in Sec. 1068.20.
(3) Add a permanent, legible label, written in block letters in
English, to a readily visible part of each exempted engine. This label
must include at least the following items:
(i) The label heading ``EMISSION CONTROL INFORMATION''.
(ii) Your corporate name and trademark.
(iii) Engine displacement, engine family identification, and model
year of
[[Page 68435]]
the engine or whom to contact for further information.
(iv) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.215
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
Sec. 1068.220 What are the provisions for exempting display engines?
(a) Anyone may request an exemption for display engines.
(b) A nonconforming display engine will be exempted if it is used
only for displays in the interest of a business or the general public.
This exemption does not apply to engines displayed for private use or
any other purpose we determine is inappropriate for a display
exemption.
(c) You may operate the exempted engine, but only if we approve
specific operation that is part of the display.
(d) You may sell or lease the exempted engine only with our advance
approval; you may not use it to generate revenue.
(e) To use this exemption, you must add a permanent, legible label,
written in block letters in English, to a readily visible part of each
exempted engine. This label must include at least the following items:
(1) The label heading ``EMISSION CONTROL INFORMATION''.
(2) Your corporate name and trademark.
(3) Engine displacement, engine family identification, and model
year of the engine or whom to contact for further information.
(4) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.220
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
(f) We may set other conditions for approval of this exemption.
Sec. 1068.225 What are the provisions for exempting engines for
national security?
(a) You are eligible for the exemption for national security only
if you are a manufacturer.
(b) Your engine is exempt without a request if you produce it for a
piece of equipment owned or used by an agency of the federal government
responsible for national defense, where the equipment has armor,
permanently attached weaponry, or other substantial features typical of
military combat.
(c) You may request a national security exemption for engines not
meeting the conditions of paragraph (b) of this section, as long as
your request is endorsed by an agency of the federal government
responsible for national defense. In your request, explain why you need
the exemption.
Sec. 1068.230 What are the provisions for exempting engines for
export?
(a) If you export a new engine to a country with emission standards
identical to ours, we will not exempt it. These engines must comply
with our certification requirements.
(b) If you export an engine to a country with different emission
standards or no emission standards, it is exempt from the prohibited
acts in this part without a request. If you produce an exempt engine
for export and it is sold or offered for sale to someone in the United
States (except for export), we will void the exemption.
(c) Label each exempted engine and shipping container with a label
or tag showing the engine is not certified for sale or use in the
United States. The label must include at least the statement ``THIS
ENGINE IS SOLELY FOR EXPORT AND IS THEREFORE IS EXEMPT UNDER 40 CFR
1068.230 FROM U.S. EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
Sec. 1068.235 What are the provisions for exempting engines used
solely for competition?
(a) New engines you produce that are used solely for competition
are generally excluded from emission standards. See the standard-
setting parts for specific provisions where applicable.
(b) If you modify an engine after it has been placed into service
in the United States so it will be used solely for competition, it is
exempt without request. This exemption applies only to the prohibition
in Sec. 1068.101(b)(1) and is valid only as long as the engine is used
solely for competition.
(c) If you modify an engine under this exemption, you must destroy
the original emission label. If you sell or give one of these engines
to someone else, you must tell the new owner in writing that it may be
used only for competition.
Sec. 1068.240 What are the provisions for exempting new replacement
engines?
(a) You are eligible for the exemption for new replacement engines
only if you are a certificate holder.
(b) The prohibitions in Sec. 1068.101(a)(1) do not apply to an
engine if all the following conditions apply:
(1) You produce a new engine to replace an engine already placed in
service in a piece of equipment.
(2) The engine being replaced was manufactured before the emission
standards that would otherwise apply to the new engine took effect.
(3) No engine certified to current emission requirements is
available with the appropriate physical or performance characteristics
for the piece of equipment.
(4) You or your agent takes possession of the old engine.
(5) You make the replacement engine in a configuration identical in
all material respects to the engine being replaced (or that of another
certified engine of the same or later model year). This requirement
applies only if the old engine was certified to emission standards less
stringent than those in effect when you produce the replacement engine.
(c) If the old engine was not certified to any emission standards
under this chapter, clearly label the replacement engine with the
following language:
THIS ENGINE DOES NOT COMPLY WITH FEDERAL NONROAD OR HIGHWAY
EMISSION REQUIREMENTS. SELLING OR INSTALLING THIS ENGINE FOR ANY
PURPOSE OTHER THAN AS A REPLACEMENT ENGINE IN A VEHICLE OR PIECE OF
EQUIPMENT BUILT BEFORE JANUARY 1, [Insert appropriate year
reflecting when standards began to apply to engines of that size and
type]
IS A VIOLATION OF FEDERAL LAW SUBJECT TO CIVIL PENALTY.
(d) If the old engine was certified to emission standards less
stringent than those in effect when you produce the replacement engine,
clearly label the replacement engine with the following language:
THIS ENGINE DOES NOT COMPLY WITH CURRENT FEDERAL NONROAD OR
HIGHWAY EMISSION REQUIREMENTS. SELLING OR INSTALLING THIS ENGINE FOR
ANY PURPOSE OTHER THAN AS A REPLACEMENT ENGINE IN A VEHICLE OR PIECE
OF EQUIPMENT BUILT BEFORE JANUARY 1, [Insert appropriate year
reflecting when the earlier tier of emission standards began to
apply to the old engine]
IS A VIOLATION OF FEDERAL LAW SUBJECT TO
CIVIL PENALTY.
Sec. 1068.245 What temporary provisions address hardship due to
unusual circumstances?
(a) After considering the circumstances, we may permit you to
introduce into commerce engines or equipment that do not comply with
emission standards if all the following conditions apply:
(1) Unusual circumstances that are clearly outside your control and
that could not have been avoided with reasonable discretion prevent you
from meeting requirements from this chapter.
(2) You exercised prudent planning and were not able to avoid the
violation; you have taken all reasonable steps to minimize the extent
of the nonconformity.
[[Page 68436]]
(3) Not having the exemption will jeopardize the solvency of your
company.
(4) No other allowances are available under the regulations in this
chapter to avoid the impending violation.
(b) To apply for an exemption, you must send the Designated Officer
a written request as soon as possible before you are in violation. In
your request, show that you meet all the conditions and requirements in
paragraph (a) of this section.
(c) Include in your request a plan showing how you will meet all
the applicable requirements as quickly as possible.
(d) You must give us other relevant information if we ask for it.
(e) We may include reasonable additional conditions on an approval
granted under this section, including provisions to recover or
otherwise address the lost environmental benefit or paying fees to
offset any economic gain resulting from the exemption. For example, in
the case of multiple tiers of emission standards, we may require that
you meet the less stringent standards.
(f) Add a permanent, legible label, written in block letters in
English, to a readily visible part of each engine exempted under this
section. This label must include at least the following items:
(1) The label heading ``EMISSION CONTROL INFORMATION''.
(2) Your corporate name and trademark.
(3) Engine displacement (in liters), rated power, and model year of
the engine or whom to contact for further information.
(4) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.245
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
Sec. 1068.250 What are the provisions for extending compliance
deadlines for small-volume manufacturers under hardship?
(a) After considering the circumstances, we may extend the
compliance deadline for you to meet new or revised emission standards,
as long as you meet all the conditions and requirements in this
section.
(b) To be eligible for this exemption, you must qualify under the
standard-setting part for special provisions for small businesses or
small-volume manufacturers.
(c) To apply for an extension, you must send the Designated Officer
a written request. In your request, show that all the following
conditions and requirements apply:
(1) You have taken all possible business, technical, and economic
steps to comply.
(i) In the case of importers of engines produced by other
companies, show that you attempted to find a manufacturer capable of
supplying complying products as soon as you became aware of the
applicable requirements, but were unable to do so.
(ii) For all other manufacturers, show that the burden of
compliance costs prevents you from meeting the requirements of this
chapter.
(2) Not having the exemption will jeopardize the solvency of your
company.
(3) No other allowances are available under the regulations in this
chapter to avoid the impending violation.
(d) In describing the steps you have taken to comply under
paragraph (c)(1) of this section, include at least the following
information:
(1) Describe your business plan, showing the range of projects
active or under consideration.
(2) Describe your current and projected financial standing, with
and without the burden of complying fully with the applicable
regulations in this chapter.
(3) Describe your efforts to raise capital to comply with
regulations in this chapter (this may not apply for importers).
(4) Identify the engineering and technical steps you have taken or
plan to take to comply with regulations in this chapter.
(5) Identify the level of compliance you can achieve. For example,
you may be able to produce engines that meet a somewhat less stringent
emission standard than the regulations in this chapter require.
(e) Include in your request a plan showing how you will meet all
the applicable requirements as quickly as possible.
(f) You must give us other relevant information if we ask for it.
(g) An authorized representative of your company must sign the
request and include the statement: ``All the information in this
request is true and accurate, to the best of my knowledge.''.
(h) Send your request for this extension at least nine months
before the relevant deadline. If different deadlines apply to companies
that are not small-volume manufacturers, do not send your request
before the regulations in question apply to the other manufacturers.
Otherwise, do not send your request more than three years before the
relevant deadline.
(i) We may include reasonable requirements on an approval granted
under this section, including provisions to recover or otherwise
address the lost environmental benefit. For example, we may require
that you meet a less stringent emission standard or buy and use
available emission credits.
(j) We will approve extensions of up to one year. We may review and
revise an extension as reasonable under the circumstances.
(k) Add a permanent, legible label, written in block letters in
English, to a readily visible part of each engine exempted under this
section. This label must include at least the following items:
(1) The label heading ``EMISSION CONTROL INFORMATION''.
(2) Your corporate name and trademark.
(3) Engine displacement (in liters), rated power, and model year of
the engine or whom to contact for further information.
(4) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.250
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
Sec. 1068.255 What are the provisions for exempting engines for
hardship for equipment manufacturers and secondary engine
manufacturers?
This section describes how, in unusual circumstances, we may exempt
certain engines to prevent a hardship to an equipment manufacturer or a
secondary engine manufacturer. This section does not apply to products
that are subject to vehicle-based emission standards.
(a) Equipment exemption. As an equipment manufacturer, you may ask
for approval to produce exempted equipment for up to 12 months. We will
generally limit this to the first year that new or revised emission
standards apply. Send the Designated Officer a written request for an
exemption before you are in violation. In your request, you must show
you are not at fault for the impending violation and that you would
face serious economic hardship if we do not grant the exemption. This
exemption is not available under this paragraph (a) if you manufacture
the engine you need for your own equipment or if complying engines are
available from other engine manufacturers that could be used in your
equipment, unless we allow it elsewhere in this chapter. We may impose
other conditions, including provisions to recover the lost
environmental benefit. In determining whether to grant the exemptions,
we will consider all relevant factors, including the following:
(1) The number of engines to be exempted.
(2) The size of your company and your ability to endure the
hardship.
[[Page 68437]]
(3) The amount of time you had to redesign your equipment to
accommodate a complying engine.
(4) Whether there was any breach of contract by an engine supplier.
(5) The potential for market disruption.
(b) Engine exemption. As an engine manufacturer, you may produce
nonconforming engines for the equipment we exempt in paragraph (a) of
this section. You do not have to request this exemption for your
engines, but you must have written assurance from equipment
manufacturers that they need a certain number of exempted engines under
this section. Add a permanent, legible label, written in block letters
in English, to a readily visible part of each exempted engine. This
label must include at least the following items:
(1) The label heading ``EMISSION CONTROL INFORMATION''.
(2) Your corporate name and trademark.
(3) Engine displacement (in liters), rated power, and model year of
the engine or whom to contact for further information.
(4) The statement ``THIS ENGINE IS EXEMPT UNDER 40 CFR 1068.255
FROM EMISSION STANDARDS AND RELATED REQUIREMENTS.''.
(c) Secondary engine manufacturers. As a secondary engine
manufacturer, you may ask for approval to produce exempted engines
under this section for up to one year. We may require you to certify
your engines to compliance levels above the emission standards that
apply. For example, if you need an exemption from a second tier of
standards, we may require you to meet the standards that applied to
earlier model years.
(1) For the purpose of this section, a secondary engine
manufacturer is a manufacturer that produces an engine by modifying an
engine that is made by a different manufacturer for a different type of
application. This includes, for example, automotive engines converted
for use in industrial applications, or land-based engines converted for
use in marine applications. This applies whether the secondary engine
manufacturer is modifying a complete or partially complete engine and
whether the engine was previously certified to emission standards or
not. To be a secondary engine manufacturer, you must not be controlled
by the manufacturer of the base engine (or by an entity that also
controls the manufacturer of the base engine). In addition, equipment
manufacturers that substantially modify engines become secondary engine
manufacturers. For the purpose of this definition, ``substantially
modify'' means changing an engine in a way that could change its
emission characteristics.
(2) The provisions in paragraph (a) of this section that apply to
equipment manufacturers requesting an exemption apply equally to you,
except that you may manufacture the engines. Before we can approve the
exemption under this section, you must commit to a plan to make up the
lost environmental benefit.
(i) If you produce uncertified engines under this exemption, we
will calculate the lost environmental benefit based on our best
estimate of uncontrolled emission rates for your engines.
(ii) If you produce engines under this exemption that are certified
to a compliance level less stringent than the emission standards that
would otherwise apply, we will calculate the lost environmental benefit
based on the compliance level you select for your engines.
(3) The labeling requirements in paragraph (b) of this section
apply to your exempted engines; however, if you certify engines to
specific compliance levels, state on the label the compliance levels
that apply to each engine.
Subpart D--Imports
Sec. 1068.301 Does this subpart apply to me?
(a) This subpart applies to you if you import into the United
States engines or equipment subject to our emission standards or
equipment containing engines subject to our emission standards.
(b) In general, engines that you import must be covered by a
certificate of conformity unless they were built before emission
standards started to apply. This subpart describes the limited cases
where we allow importation of exempt or excluded engines.
(c) The U.S. Customs Service may prevent you from importing an
engine if you do not meet the requirements of this subpart. In
addition, U.S. Customs Service regulations may contain other
requirements for engines imported into the United States (see 19 CFR
Chapter I).
Sec. 1068.305 How do I get an exemption or exclusion for imported
engines?
(a) Complete the appropriate EPA declaration form before importing
any nonconforming engine. These forms are available on the Internet at
http://www.epa.gov/OMS/imports/ or by phone at 202-564-9660.
(b) If we ask for it, prepare a written request in which you do the
following:
(1) Give your name, address, telephone number, and taxpayer
identification number.
(2) Give the engine owner's name, address, telephone number, and
taxpayer identification number.
(3) Identify the make, model, identification number, and original
production year of each engine.
(4) Identify which exemption or exclusion in this subpart allows
you to import a nonconforming engine and describe how your engine
qualifies.
(5) Tell us where you will keep your engines if you might need to
store them until we approve your request.
(6) Authorize us to inspect or test your engines as the Act allows.
(c) We may ask for more information.
(d) You may import the nonconforming engines you identify in your
request if you get prior written approval from us. The U.S. Customs
Service may require you to show them the approval letter. We may
temporarily or permanently approve the exemptions or exclusions, as
described in this subpart.
(e) Make sure the engine meets any labeling requirements that
apply.
Sec. 1068.310 What are the exclusions for imported engines?
Emission standards do not apply to excluded engines that you
import. If you show us that your engines qualify under one of the
paragraphs of this section, we will approve your request to import
excluded engines. You must have our approval to import an engine under
paragraph (a) of this section. You may, but are not required to request
our approval for the other exclusions in this section. The following
engines are excluded:
(a) Engines used solely for competition. Engines you use solely for
competition are excluded. The standard-setting part may set special
provisions for the manufacture, sale, or import of engines used solely
for competition. Section 1068.101(b)(4) prohibits using these excluded
engines for other purposes.
(b) Stationary engines. This includes engines that will be used in
a permanently fixed location and engines meeting the criteria for the
exclusion in paragraph (2)(iii) of the nonroad engine definition in
Sec. 1068.30. Section 1068.101(b)(3) prohibits using these engines for
other purposes.
(c) Other engines. The standard-setting parts may exclude engines
used in certain applications. For example, engines used in aircraft,
underground mining, and hobby vehicles are generally excluded.
[[Page 68438]]
Sec. 1068.315 What are the permanent exemptions for imported engines?
We may approve a permanent exemption for an imported engine under
the following conditions:
(a) National security exemption. You may import engine under the
national security exemption in Sec. 1068.225.
(b) Manufacturer-owned engine exemption. You may import a
manufacturer-owned engine, as described in Sec. 1068.215.
(c) Replacement engine exemption. You may import a nonconforming
replacement engine as described in Sec. 1068.240. To use this
exemption, you must be a certificate holder for an engine family we
regulate under the same part as the replacement engine.
(d) Extraordinary circumstances exemption. You may import a
nonconforming engine if we grant hardship relief as described in Sec.
1068.245.
(e) Hardship exemption. You may import a nonconforming engine if we
grant an exemption for the transition to new or revised emission
standards, as described in Sec. 1068.255.
(f) Identical configuration exemption. You may import a
nonconforming engine if it is identical to certified engines produced
by the same manufacturer, subject to the following provisions:
(1) You may import only the following engines under this exemption:
(i) Large nonroad spark-ignition engines (see part 1048 of this
chapter).
(ii) Recreational nonroad spark-ignition engines and equipment (see
part 1051 of this chapter).
(2) You must meet all the following criteria:
(i) You have owned the engine for at least one year.
(ii) You agree not to sell, lease, donate, trade, or otherwise
transfer ownership of the engine for at least five years, or until the
engine is eligible for the exemption in paragraph (g) of this section.
During this period, the only acceptable way to dispose of the engine is
to destroy or export it.
(iii) You use data or evidence sufficient to show that the engine
is in a configuration that is the same as an engine the original
manufacturer has certified to meet emission standards that apply at the
time the manufacturer finished assembling or modifying the engine in
question. If you modify the engine to make it identical, you must
follow the original manufacturer's complete written instructions.
(3) We will tell you in writing if we find the information
insufficient to show that the engine is eligible for this exemption. In
this case, we will not consider your request further until you address
our concerns.
(g) Ancient engine exemption. If you are not the original engine
manufacturer, you may import a nonconforming engine that is subject to
a standard-setting part and was first manufactured at least 21 years
earlier, as long as it is still in its original configuration.
Sec. 1068.320 How must I label an imported engine with a permanent
exemption?
(a) For engines imported under Sec. 1068.315 (a), (b), (c), (d),
or (e), you must place a permanent label or tag on each engine. If no
specific label requirements from subpart C of this part apply, you must
meet the following requirements:
(1) Attach the label or tag in one piece so no one can remove it
without destroying or defacing it.
(2) Make sure it is durable and readable for the engine's entire
life.
(3) Secure it to a part of the engine needed for normal operation
and not normally requiring replacement.
(4) Write it in block letters in English.
(5) Make it readily visible to the average person after the engine
is installed in the equipment.
(b) On the engine label or tag, do the following:
(1) Include the heading ``Emission Control Information.''
(2) Include your full corporate name and trademark.
(3) State the engine displacement (in liters) and rated power. If
the engine's rated power is not established, state the approximate
power rating accurately enough to allow a detemination of which
stanadards would otherwise apply.
(4) State: ``THIS ENGINE IS EXEMPT FROM THE REQUIREMENTS OF
[identify the part referenced in 40 CFR 1068.1(a) that would otherwise
apply], AS PROVIDED IN [identify the paragraph authorizing the
exemption (for example, ``40 CFR 1068.315(a)'')]. INSTALLING THIS
ENGINE IN ANY DIFFERENT APPLICATION IS A VIOLATION OF FEDERAL LAW
SUBJECT TO CIVIL PENALTY.''.
(c) Get us to approve alternate label language if it is more
accurate for your engine.
Sec. 1068.325 What are the temporary exemptions for imported engines?
If we approve a temporary exemption for an engine, you may import
it under the conditions in this section. We may ask the U.S. Customs
Service to require a specific bond amount to make sure you comply with
the requirements of this subpart. You may not sell or lease one of
these engines while it is in the United States. You must eventually
export the engine as we describe in this section unless you get a
certificate of conformity for it or it qualifies for one of the
permanent exemptions in Sec. 1068.315. Section 1068.330 specifies an
additional temporary exemption allowing you to import certain engines
you intend to sell or lease.
(a) Exemption for repairs or alterations. You may temporarily
import a nonconforming engine under bond solely to repair or alter it.
You may operate the engine in the United States only to repair or alter
it or to ship it to or from the service location. Export the engine
directly after the engine servicing is complete.
(b) Testing exemption. You may temporarily import a nonconforming
engine under bond for testing if you follow the requirements of Sec.
1068.210. You may operate the engine in the United States only to allow
testing. This exemption expires one year after you import the engine,
unless we approve a one-time request for an extension of up to one more
year. The engine must be exported before the exemption expires.
(c) Display exemption. You may temporarily import a nonconforming
engine under bond for display, as described in Sec. 1068.220. This
exemption expires one year after you import the engine, unless we
approve your request for an extension. We may approve an extension of
up to one more year for each request, but no more than three years in
total. The engine must be exported by the time the exemption expires or
directly after the display concludes, whichever comes first.
(d) Export exemption. You may temporarily import a nonconforming
engine to export it, as described in Sec. 1068.230. You may operate
the engine in the United States only as needed to prepare it for
export. Label the engine as described in Sec. 1068.230.
(e) Diplomatic or military exemption. You may temporarily import
nonconforming engines without bond if you represent a foreign
government in a diplomatic or military capacity. In your request to the
Designated Officer (see Sec. 1068.305), include either written
confirmation from the U.S. State Department that you qualify for this
exemption or a copy of your orders for military duty in the United
States. We will rely on the State Department or your military orders to
determine when your diplomatic or military status expires, at which
time you must export your exempt engines.
[[Page 68439]]
Sec. 1068.330 How do I import engines to modify for other
applications?
This section allows you to import engines in configurations
different than their final configuration. This exemption is temporary,
as described in paragraph (d) of this section.
(a) This section applies in the following cases:
(1) You import a partially complete engine with the intent to
manufacture complete engines for which you have either a certificate of
conformity or an exemption that allows you to sell completed engines.
(2) You import an uncertified complete engine with the intent to
modify it for installation in an application different than its
otherwise intended application (for example, you import a land-based
engine to modify it for a marine application). In this case, to qualify
for an exemption under this section, you need either a certificate of
conformity or an exemption that allows you to sell completed engines.
(3) You import a complete or partially complete engine to modify
for an application for which emission standards do not apply.
(b) You may request this exemption in an application for
certification. Otherwise, send your request to the Designated Officer.
Your request must include:
(1) The name of the supplier of the partially complete engine, or
the original manufacturer of the complete engine.
(2) A description of the certificate or exemption that will apply
to the engines in the final configuration, or an explanation why a
certificate or exemption is not needed.
(3) A brief description of how and where final assembly will be
completed.
(4) An unconditional statement that the engines will comply with
all applicable regulations in their final configuration.
(c) If we approve a temporary exemption for an engine, you may
import it under the conditions in this section. We may ask the U.S.
Customs Service to require a specific bond amount to make sure you
comply with the requirements of this subpart.
(d) These provisions are intended only to allow you to import
engines in the specific circumstances identified in this section, so
any exemption under this section expires when you complete the assembly
of the engine in its final configuration. If the engine in its final
configuration is subject to emission standards, then it must be covered
by a certificate or a different exemption before you introduce it into
commerce.
Sec. 1068.335 What are the penalties for violations?
(a) All imported engines. Unless you comply with the provisions of
this subpart, importation of nonconforming engines is violation of
sections 203 and 213(d) of the Act. You may then have to export the
engines, or pay civil penalties, or both. The U.S. Customs Service may
seize unlawfully imported engines.
(b) Temporarily imported engines. If you do not comply with the
provisions of this subpart for a temporary exemption, you may forfeit
the total amount of the bond in addition to the sanctions we identify
in paragraph (a) of this section. We will consider an engine to be
exported if it has been destroyed or delivered to the U.S. Customs
Service for export or other disposition under applicable Customs laws
and regulations. EPA or the U.S. Customs Service may offer you a grace
period to allow you to export a temporarily exempted engine without
penalty after the exemption expires.
Subpart E--Selective Enforcement Auditing
Sec. 1068.401 What is a selective enforcement audit?
(a) We may conduct or require you to conduct emission tests on your
production engines in a selective enforcement audit. This requirement
is independent of any requirement for you to routinely test production-
line engines.
(b) If we send you a signed test order, you must follow its
directions and the provisions of this subpart. We will tell you where
to test the engines. This may be where you produce the engines or any
other emission testing facility.
(c) If we select one or more of your engine families for a
selective enforcement audit, we will send the test order to the person
who signed the application for certification or we will deliver it in
person.
(d) Within one working day of receiving the test order, notify the
Designated Officer which test facility you have selected for emission
testing.
(e) You must do everything we require in the audit without delay.
Sec. 1068.405 What is in a test order?
(a) In the test order, we will specify the following things:
(1) The engine family and configuration (if any) we have identified
for testing.
(2) The engine assembly plant, storage facility, or (if you import
the engines) port facility from which you must select engines.
(3) The procedure for selecting engines for testing, including a
selection rate.
(4) The test procedures, duty cycles, and test points, as
appropriate, for testing the engines to show that they meet emission
standards.
(b) We may state that we will select the test engines.
(c) We may identify alternate engine families or configurations for
testing in case we determine the intended engines are not available for
testing or if you do not produce enough engines to meet the minimum
rate for selecting test engines.
(d) We may include other directions or information in the test
order.
(e) We may ask you to show us that you meet any additional
requirements that apply to your engines (closed crankcases, for
example).
(f) In anticipation of a potential audit, you may give us a list of
your preferred engine families and the corresponding assembly plants,
storage facilities, or (if you import the engines) port facilities from
which we should select engines for testing. The information would apply
only for a single model year, so it would be best to include this
information in your application for certification. If you give us this
list before we issue a test order, we will consider your
recommendations, but we may select engines differently.
(g) If you also do routine production-line testing with the
selected engine family in the same time period, the test order will
tell you what changes you might need to make in your production-line
testing schedule.
Sec. 1068.410 How must I select and prepare my engines?
(a) Selecting engines. Select engines as described in the test
order. If you are unable to select test engines this way, you may ask
us to approve an alternate plan, as long as you make the request before
you start selecting engines.
(b) Assembling engines. Produce and assemble test engines using
your normal production and assembly process for that engine family.
(1) Notify us directly if you make any change in your production,
assembly, or quality control processes that might affect emissions
between the time you receive the test order and the time you finish
selecting test engines.
(2) If you do not fully assemble engines at the specified location,
we will describe in the test order how to select components to finish
assembling the engines. Assemble these components onto the test engines
using your documented assembly and quality control procedures.
(c) Modifying engines. Once an engine is selected for testing, you
may adjust,
[[Page 68440]]
repair, prepare, or modify it or check its emissions only if one of the
following is true:
(1) You document the need for doing so in your procedures for
assembling and inspecting all your production engines and make the
action routine for all the engines in the engine family.
(2) This subpart otherwise allows your action.
(3) We approve your action in advance.
(d) Engine malfunction. If an engine malfunction prevents further
emission testing, ask us to approve your decision to either repair the
engine or delete it from the test sequence.
(e) Setting adjustable parameters. Before any test, we may adjust
or require you to adjust any adjustable parameter to any setting within
its physically adjustable range.
(1) We may adjust idle speed outside the physically adjustable
range as needed until the engine has stabilized emission levels (see
paragraph (e) of this section). We may ask you for information needed
to establish an alternate minimum idle speed.
(2) We may make or specify adjustments within the physically
adjustable range by considering their effect on emission levels, as
well as how likely it is someone will make such an adjustment with in-
use engines.
(f) Stabilizing emission levels. Before you test production-line
engines, you may operate the engine to stabilize the emission levels.
Using good engineering judgment, operate your engines in a way that
represents the way production engines will be used. You may operate
each engine for no more than the greater of two periods:
(1) 50 hours.
(2) The number of hours you operated your emission-data engine for
certifying the engine family (see 40 CFR part 1065, subpart E).
(g) Damage during shipment. If shipping an engine to a remote
facility for production-line testing makes necessary an adjustment or
repair, you must wait until after the initial emission test to do this
work. We may waive this requirement if the test would be impossible or
unsafe, or if it would permanently damage the engine. Report to us, in
your written report under Sec. 1068.450, all adjustments or repairs
you make on test engines before each test.
(h) Shipping engines. If you need to ship engines to another
facility for testing, make sure the test engines arrive at the test
facility within 24 hours after being selected. You may ask that we
allow more time if you are unable to do this.
(i) Retesting after invalid tests. You may retest an engine if you
determine an emission test is invalid. Explain in your written report
reasons for invalidating any test and the emission results from all
tests. If you retest an engine and, within ten days after testing, ask
to substitute results of the new tests for the original ones, we will
answer within ten days after we receive your information.
Sec. 1068.415 How do I test my engines?
(a) Use the test procedures specified in the standard-setting part
for showing that your engines meet emission standards. The test order
will give further testing instructions.
(b) If no test cells are available at a given facility, you may
make alternate testing arrangements with our approval.
(c) Test at least two engines in each 24-hour period (including
void tests). However, if your projected U.S. nonroad engine sales
within the engine family are less than 7,500 for the year, you may test
a minimum of one engine per 24-hour period. If you request and justify
it, we may approve a lower testing rate.
(d) Accumulate service on test engines at a minimum rate of 6 hours
per engine during each 24-hour period. The first 24-hour period for
service accumulation begins when you finish preparing an engine for
testing. The minimum service accumulation rate does not apply on
weekends or holidays. You may ask us to approve a lower service
accumulation rate. Plan your service accumulation to allow testing at
the rate specified in Sec. 1068.415. Select engine operation for
accumulating operating hours on your test engines to represent normal
in-use engine operation for the engine family.
(e) Test engines is the same order you select them.
Sec. 1068.420 How do I know when my engine family fails an SEA?
(a) A failed engine is one whose final deteriorated test results
exceed an applicable emission standard for any regulated pollutant.
(b) Continue testing engines until you reach a pass decision for
all pollutants or a fail decision for one pollutant.
(c) You reach a pass decision for the SEA requirements when the
number of failed engines is less than or equal to the pass decision
number in Appendix A to this subpart for the total number of engines
tested. You reach a fail decision for the SEA requirements when the
number of failed engines is greater than or equal to the fail decision
number in Appendix A to this subpart for the total number of engines
you test. An acceptable quality level of 40 percent is the basis for
the pass or fail decision.
(d) Consider test results in the same order as the engine testing
sequence.
(e) If you reach a pass decision for one pollutant, but need to
continue testing for another pollutant, we will disregard these later
test results for the pollutant with the pass decision.
(f) Appendix A to this subpart lists multiple sampling plans. Use
the sampling plan for the projected sales volume you reported in your
application for the audited engine family.
(g) We may choose to stop testing after any number of tests.
(h) If we test some of your engines in addition to your own
testing, we may decide not to include your test results as official
data for those engines if there is substantial disagreement between
your testing and our testing. We will reinstate your data as valid if
you show us that we made an error and your data are correct.
(i) If we rely on our test data instead of yours, we will notify
you in writing of our decision and the reasons we believe your facility
is not appropriate for doing the tests we require under this subpart.
You may request in writing that we consider your test results from the
same facility for future testing if you show us that you have made
changes to resolve the problem.
Sec. 1068.425 What happens if one of my production-line engines
exceeds the emission standards?
(a) If one of your production-line engines fails to meet one or
more emission standards (see Sec. 1068.420), the certificate of
conformity is automatically suspended for that engine. You must take
the following actions before your certificate of conformity can cover
that engine:
(1) Correct the problem and retest the engine to show it complies
with all emission standards.
(2) Include in your written report a description of the test
results and the remedy for each engine (see Sec. 1068.450).
(b) You may at any time ask for a hearing to determine whether the
tests and sampling methods were proper (see subpart G of this part).
Sec. 1068.430 What happens if an engine family fails an SEA?
(a) We may suspend your certificate of conformity for an engine
family if it fails the SEA under Sec. 1068.420. The suspension may
apply to all facilities producing engines from an engine family, even
if you find noncompliant engines only at one facility.
(b) We will tell you in writing if we suspend your certificate in
whole or in
[[Continued on page 68441]]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
]
[[pp. 68441-68447]]
Control of Emissions From Nonroad Large Spark-Ignition Engines,
and Recreational Engines (Marine and Land-Based)
[[Continued from page 68440]]
[[Page 68441]]
part. We will not suspend a certificate until at least 15 days after
the engine family fails the SEA. The suspension is effective when you
receive our notice.
(c) Up to 15 days after we suspend the certificate for an engine
family, you may ask for a hearing to determine whether the tests and
sampling methods were proper (see subpart G of this part). If we agree
before a hearing that we used erroneous information in deciding to
suspend the certificate, we will reinstate the certificate.
Sec. 1068.435 May I sell engines from an engine family with a
suspended certificate of conformity?
You may sell engines that you produce after we suspend the engine
family's certificate of conformity only if one of the following occurs:
(a) You test each engine you produce and show it complies with
emission standards that apply.
(b) We conditionally reinstate the certificate for the engine
family. We may do so if you agree to recall all the affected engines
and remedy any noncompliance at no expense to the owner if later
testing shows that engines in the engine family still do not comply.
Sec. 1068.440 How do I ask EPA to reinstate my suspended certificate?
(a) Send us a written report asking us to reinstate your suspended
certificate. In your report, identify the reason for the SEA failure,
propose a remedy, and commit to a date for carrying it out. In your
proposed remedy include any quality control measures you propose to
keep the problem from happening again.
(b) Give us data from production-line testing showing that engines
in the remedied engine family comply with all the emission standards
that apply.
Sec. 1068.445 When may EPA revoke my certificate under this subpart
and how may I sell these engines again?
(a) We may revoke your certificate for an engine family in the
following cases:
(1) You do not meet the reporting requirements.
(2) Your engine family fails an SEA and your proposed remedy to
address a suspended certificate is inadequate to solve the problem or
requires you to change the engine's design or emission-control system.
(b) To sell engines from an engine family with a revoked
certificate of conformity, you must modify the engine family and then
show it complies with the applicable requirements.
(1) If we determine your proposed design change may not control
emissions for the engine's full useful life, we will tell you within
five working days after receiving your report. In this case we will
decide whether production-line testing will be enough for us to
evaluate the change or whether you need to do more testing.
(2) Unless we require more testing, you may show compliance by
testing production-line engines as described in this subpart.
(3) We will issue a new or updated certificate of conformity when
you have met these requirements.
Sec. 1068.450 What records must I send to EPA?
(a) Within 30 calendar days of the end of each audit, send us a
report with the following information:
(1) Describe any facility used to test production-line engines and
state its location.
(2) State the total U.S.-directed production volume and number of
tests for each engine family.
(3) Describe your test engines, including the engine family's
identification and the engine's model year, build date, model number,
identification number, and number of hours of operation before testing
for each test engine.
(4) Identify where you accumulated hours of operation on the
engines and describe the procedure and schedule you used.
(5) Provide the test number; the date, time and duration of
testing; test procedure; initial test results before and after
rounding; final test results; and final deteriorated test results for
all tests. Provide the emission figures for all measured pollutants.
Include information for both valid and invalid tests and the reason for
any invalidation.
(6) Describe completely and justify any nonroutine adjustment,
modification, repair, preparation, maintenance, or test for the test
engine if you did not report it separately under this subpart. Include
the results of any emission measurements, regardless of the procedure
or type of equipment.
(7) Report on each failed engine as described in Sec. 1068.425.
(b) We may ask you to add information to your written report, so we can
determine whether your new engines conform with the requirements of
this subpart.
(c) An authorized representative of your company must sign the
following statement:
We submit this report under Sections 208 and 213 of the Clean
Air Act. Ourtesting conformed completely with the requirements of 40
CFR part 1068. We have not changed production processes or quality-
control procedures for the engine family in a way that might affect
the emission control from production engines. All the information in
this report is true and accurate, to the best of my knowledge. I
know of the penalties for violating the Clean Air Act and the
regulations. (Authorized Company Representative)
(d) Send reports of your testing to the Designated Officer using an
approved information format. If you want to use a different format,
send us a written request with justification for a waiver.
(e) We will send copies of your reports to anyone from the public
who asks for them. We will release information about your sales or
production volumes, which is all we will consider confidential.
Sec. 1068.455 What records must I keep?
(a) We may review your records at any time, so it is important to
keep required information readily available. Organize and maintain your
records as described in this section.
(b) Keep paper records for testing under this subpart for one full
year after you complete all the testing required for the selective
enforcement audit. For additional storage, you may use any format or
media.
(c) Keep a copy of the written reports described in Sec. 1068.450.
(d) Keep the following additional records:
(1) The names of supervisors involved in each test.
(2) The name of anyone who authorizes adjusting, repairing,
preparing, or modifying a test engine and the names of all supervisors
who oversee this work.
(3) If you shipped the engine for testing, the date you shipped it,
the associated storage or port facility, and the date the engine
arrived at the testing facility.
(4) Any records related to your audit that are not in the written
report.
(5) A brief description of any significant events during testing
not otherwise described in the written report or in this section.
(e) If we ask, you must give us projected or actual production for
an engine family. Include each assembly plant if you produce engines at
more than one plant.
(f) We may ask you to keep or send other information necessary to
implement this subpart.
Appendix A to Subpart E of Part 1068--Plans for Selective Enforcement
Auditing
The following tables describe sampling plans for selective
enforcement audits, as described in Sec. 1068.420:
[[Page 68442]]
Table A-1.--Sampling Plan Code Letter
----------------------------------------------------------------------------------------------------------------
Minimum number of tests Maximum
Projected engine family sales Code letter ---------------------------- number of
\1\ To pass To fail tests
----------------------------------------------------------------------------------------------------------------
20 - 50................................................. AA 3 5 20
20 - 99................................................. A 4 6 30
100 - 299............................................... B 5 6 40
300 - 499............................................... C 5 6 50
500 +................................................... D 5 6 60
----------------------------------------------------------------------------------------------------------------
\1\ A manufacturer may optionally use either the sampling plan for code letter ``AA'' or sampling plan for code
letter ``A'' for Selective enforcement Audits of engine families with annual sales between 20 and 50 engines.
Additionally, the manufacturer may switch between these plans during the audit.
Table A-2.--Sampling Plans for Different Engine Family Sales Volumes
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
AA A B C D
-------------------------------------------------------------------------------------------------------------------------------------------
Stage a Pass i> i> i> i> i> i> i> i> i>
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
1...................................................
-----------------------------------------------------
2...................................................
-----------------------------------------------------
3................................................... 0
-----------------------------------------------------
4................................................... ............ ............ 0
-----------------------------------------------------
5................................................... 1 5 0 ............ 0 ............ 0 ............ 0
-----------------------------------------------------
6................................................... 1 6 1 6 1 6 0 6 0 6
-----------------------------------------------------
7................................................... 2 6 1 7 1 7 1 7 1 7
-----------------------------------------------------
8................................................... 2 7 2 7 2 7 2 7 2 8
-----------------------------------------------------
9................................................... 3 7 2 8 2 8 2 8 2 8
-----------------------------------------------------
10.................................................. 3 8 3 8 3 8 3 9 3 9
-----------------------------------------------------
11.................................................. 4 8 3 8 3 9 3 9 3 9
-----------------------------------------------------
12.................................................. 4 9 4 9 4 9 4 10 4 10
-----------------------------------------------------
13.................................................. 5 9 5 10 4 10 4 10 4 10
-----------------------------------------------------
14.................................................. 5 10 5 10 5 10 5 11 5 11
-----------------------------------------------------
15.................................................. 6 10 6 11 5 11 5 11 5 11
-----------------------------------------------------
16.................................................. 6 10 6 11 6 12 6 12 6 12
-----------------------------------------------------
17.................................................. 7 10 7 12 6 12 6 12 6 12
-----------------------------------------------------
18.................................................. 8 10 7 12 7 13 7 13 7 13
-----------------------------------------------------
19.................................................. 8 10 8 13 8 13 7 13 7 13
-----------------------------------------------------
20.................................................. 9 10 8 13 8 14 8 14 8 14
-----------------------------------------------------
21.................................................. ............ ............ 9 14 9 14 8 14 8 14
-----------------------------------------------------
22.................................................. ............ ............ 10 14 9 15 9 15 9 15
-----------------------------------------------------
23.................................................. ............ ............ 10 15 10 15 10 15 9 15
-----------------------------------------------------
24.................................................. ............ ............ 11 15 10 16 10 16 10 16
-----------------------------------------------------
25.................................................. ............ ............ 11 16 11 16 11 16 11 16
-----------------------------------------------------
26.................................................. ............ ............ 12 16 11 17 11 17 11 17
-----------------------------------------------------
27.................................................. ............ ............ 12 17 12 17 12 17 12 17
-----------------------------------------------------
28.................................................. ............ ............ 13 17 12 18 12 18 12 18
-----------------------------------------------------
29.................................................. ............ ............ 14 17 13 18 13 18 13 19
-----------------------------------------------------
30.................................................. ............ ............ 16 17 13 19 13 19 13 19
-----------------------------------------------------
31.................................................. ............ ............ ............ ............ 14 19 14 19 14 20
-----------------------------------------------------
32.................................................. ............ ............ ............ ............ 14 20 14 20 14 20
[[Page 68443]]
-----------------------------------------------------
33.................................................. ............ ............ ............ ............ 15 20 15 20 15 21
-----------------------------------------------------
34.................................................. ............ ............ ............ ............ 16 21 15 21 15 21
-----------------------------------------------------
35.................................................. ............ ............ ............ ............ 16 21 16 21 16 22
-----------------------------------------------------
36.................................................. ............ ............ ............ ............ 17 22 16 22 16 22
-----------------------------------------------------
37.................................................. ............ ............ ............ ............ 17 22 17 22 17 23
-----------------------------------------------------
38.................................................. ............ ............ ............ ............ 18 22 18 23 17 23
-----------------------------------------------------
39.................................................. ............ ............ ............ ............ 18 22 18 23 18 24
-----------------------------------------------------
40.................................................. ............ ............ ............ ............ 21 22 19 24 18 24
-----------------------------------------------------
41.................................................. ............ ............ ............ ............ ............ ............ 19 24 19 25
-----------------------------------------------------
42.................................................. ............ ............ ............ ............ ............ ............ 20 25 19 26
-----------------------------------------------------
43.................................................. ............ ............ ............ ............ ............ ............ 20 25 20 26
-----------------------------------------------------
44.................................................. ............ ............ ............ ............ ............ ............ 21 26 21 27
-----------------------------------------------------
45.................................................. ............ ............ ............ ............ ............ ............ 21 27 21 27
-----------------------------------------------------
46.................................................. ............ ............ ............ ............ ............ ............ 22 27 22 28
-----------------------------------------------------
47.................................................. ............ ............ ............ ............ ............ ............ 22 27 22 28
-----------------------------------------------------
48.................................................. ............ ............ ............ ............ ............ ............ 23 27 23 29
-----------------------------------------------------
49.................................................. ............ ............ ............ ............ ............ ............ 23 27 23 29
-----------------------------------------------------
50.................................................. ............ ............ ............ ............ ............ ............ 26 27 24 30
-----------------------------------------------------
51.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 24 30
-----------------------------------------------------
52.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 25 31
-----------------------------------------------------
53.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 25 31
-----------------------------------------------------
54.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 26 32
-----------------------------------------------------
55.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 26 32
-----------------------------------------------------
56.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 27 33
-----------------------------------------------------
57.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 27 33
-----------------------------------------------------
58.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 28 33
-----------------------------------------------------
59.................................................. ............ ............ ............ ............ ............ ............ ............ ............ 28 33
-----------------------------------------------------
60 ............ ............ ............ ............ ............ ............ ............ ............ 32 33
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
\a\ Stage refers to the cumulative number of engines tested.
Subpart F--Reporting Defects and Recalling Engines
Sec. 1068.501 How do I report engine defects?
(a) General provisions. As an engine manufacturer, you must
investigate in certain circumstances whether emission-related
components are defective and send us reports as specified by this
section.
(1) The term emission-related component includes those components
listed in Appendix I of this part. For the purposes of this section,
complete engines shall also be considered an emissions-related
component. It also includes factory settings of emission-related
parameters and specifications listed in Appendix II of this part.
(2) For the purposes of this section, defects do not include damage
to emission-related components (or maladjustment of parameters) caused
by owners improperly maintaining or abusing their engine.
(3) You must track the information specified in paragraph (b)(1) of
this section. You are not required to collect additional information
other than that specified in paragraph (b)(1) of this section before
reaching the threshold for an investigation specified in paragraph (e)
of this section.
(4) You may ask us to allow you to use alternate methods for
tracking, investigating, reporting, and correcting emission-related
defects. In your request, explain and demonstrate why you believe your
alternate system will be at least as effective in tracking,
identifying, investigating, evaluating, reporting, and correcting
potential and actual emissions-related defects as the requirements in
this section.
(5) If we determine that emission-related defects result in a
substantial number of properly maintained and used engines not
conforming to the regulations of this chapter during their
[[Page 68444]]
useful life, we may order you to conduct a recall of your engines (see
Sec. 1068.505).
(6) Send the defect reports and status reports required by this
section to the Designated Officer.
(b) Investigation of possible defects. If the number of engines
that possibly have a defect, as defined by paragraph (b)(1) of this
section, exceed the thresholds specified in paragraph (e) of this
section, you must conduct an investigation to determine if an emission-
related component is actually defective.
(1) You must track warranty claims, parts shipments, and the other
information specified in paragraph (b)(1)(iii) of this section. You
must classify an engine as possibly having a defective component if any
of the following is true:
(i) A warranty claim is submitted for the component, whether this
is under your emission-related warranty or any other warranty.
(ii) You ship a replacement component other than for normally
scheduled maintenance during the useful life of the engine.
(iii) You receive any other information indicating the component
may be defective, such as information from dealers or hot line
complaints.
(2) Your investigation must be prompt, thorough, consider all
relevant information, follow scientific and engineering principles, and
be designed to obtain all the information specified in paragraph (d) of
this section.
(3) Your investigation only needs to consider defects that occur
within the useful life period, or within five years after the end of
the model year, whichever is longer.
(4) You must continue your investigation until you are able to
obtain all the information specified for a defect report in paragraph
(d) of this section. Send us an updated defect report anytime you have
significant additional information.
(5) If a component believed to be defective is used in additional
engine families or model years, you must investigate whether the
component or part is defective when used in these additional engine
families or model years, and include these results as part of your
defect report.
(6) If your initial investigation concludes that the number of
engines with a defect is fewer than the thresholds specified in
paragraph (f) of this section, but other information becomes available
that may show that the number of engines with a defect exceeds these
thresholds, then you must resume your investigation. If you resume an
investigation, you must include the information from the earlier
investigation to determine whether to send a defect report.
(c) Reporting defects. You must send us a defect report in either
of the following cases:
(1) Your investigation shows that the number of engines with a
defect exceeds the thresholds specified in paragraph (f) of this
section. Send the defect report within 15 days after the date you
identify this number of defective engines.
(2) You know a defective emission-related component exists in a
number of engines that exceeds the thresholds specified in paragraph
(f) of this section, regardless of how you obtain this information.
Send the defect report within 15 days after you learn that the number
of defects exceeds one of these thresholds.
(d) Contents of a defect report. Include the following information
in a defect report:
(1) Your corporate name and a person to contact regarding this
defect.
(2) A description of the defect, including a summary of any
engineering analyses and associated data, if available.
(3) A description of the engines that may have the defect,
including engine families, models, and range of production dates. Note
that you must address all model years for the engines, not just the
model year for which you triggered the reporting requirement.
(4) An estimate of the number and percentage of each class or
category of affected engines that have or may have the defect, and an
explanation of how you determined this number.
(5) An estimate of the defect's impact on emissions, with an
explanation of how you calculated this estimate and a summary of any
emission data demonstrating the impact of the defect, if available.
(6) A description of your plan for addressing the defect or an
explanation of your reasons for not believing the defects must be
remedied.
(e) Thresholds for conducting a defect investigation. Unless the
standard-setting part specifies otherwise, you must begin a defect
investigation based on the following threshold values:
(1) For engine with rated power under 560 kW:
(i) When the component is a catalytic converter (or other
aftertreatment device), if the number of engines in an engine family
that may have the defect exceeds 2 percent of the total number of
engines in the engine family or 2,000 engines, whichever is less.
(ii) When the emission-related component is anything but a
catalytic converter (or other aftertreatment device), if the number of
engines in an engine family that may have the defect exceeds 4 percent
of the total number of engines in the engine family or 4,000 engines,
whichever is less.
(2) For engine with rated power greater than or equal to 560 kW, if
the number of engines in an engine family that may have the defect
exceeds 1 percent of the total number of engines in the engine family
or 5 engines, whichever is greater.
(f) Thresholds for filing a defect report. You must send a defect
report based on the following threshold values:
(1) For engine with rated power under 560 kW:
(i) When the component is a catalytic converter (or other
aftertreatment device), if the number of engines in an engine family
that has the defect exceeds 0.125 percent of the total number of
engines in the engine family or 125 engines, whichever is less.
(ii) When the emission-related component is anything but a
catalytic converter (or other aftertreatment device), if the number of
engines in an engine family that has the defect exceeds 0.250 percent
of the total number of engines in the engine family or 250 engines,
whichever is less.
(2) For engine with rated power greater than or equal to 560 kW, if
the number of engines in an engine family that has the defect exceeds
0.5 percent of the total number of engines in the engine family or 2
engines, whichever is greater.
(g) How to count defects. In most cases, you may track defects
separately for each model year and engine family. For families with
annual U.S.-directed production volumes under 5,000 engines, you may
apply the percentage thresholds in paragraphs (e) and (f) of this
section on the basis of multiple model years, for engines using the
same emission-related components. To determine whether you exceed the
investigation threshold in paragraph (e) of this section, count defects
that you correct before they reach the ultimate purchaser. Do not count
these corrected defects to determine whether you exceed the reporting
threshold in paragraph (f) of this section.
(h) Status reports. You must send us a mid-year or end-of-year
status report if you concluded an investigation during the previous six
months without filing a defect report or if you have an unresolved
investigation at the end of the six-month period. Include the
information specified in paragraph (c) of this section, or explain why
the information is not relevant. Send these
[[Page 68445]]
status reports no later than June 30 and December 31 of each year.
(i) Future production. If you identify a design or manufacturing
defect that prevents engines from meeting the requirements of this
part, you must correct the defect as soon as possible for any future
production for engines in every family affected by the defect. This
applies without regard to whether you are required to conduct a defect
investigation or submit a defect report under this section.
Sec. 1068.505 How does the recall program work?
(a) If we make a determination that a substantial number of
properly maintained and used engines do not conform to the regulations
of this chapter during their useful life, you must submit a plan to
remedy the nonconformity of your engines. We will notify you of our
determination in writing. Our notice will identify the class or
category of engines affected and describe how we reached our
conclusion. If this happens, you must meet the requirements and follow
the instructions in this subpart. You must remedy at your expense
noncompliant engines that have been properly maintained and used. You
may not transfer this expense to a dealer or equipment manufacturer
through a franchise or other agreement.
(b) You may ask for a hearing if you disagree with our
determination (see subpart G of this part).
(c) Unless we withdraw the determination of noncompliance, you must
respond to it by sending a remedial plan to the Designated Officer by
the later of these two deadlines:
(1) Within 60 days after we notify you.
(2) Within 60 days after a hearing.
(d) Once you have sold an engine to the ultimate purchaser, we may
inspect or test the engine only if he or she permits it, or if state or
local inspection programs separately provide for it.
(e) You may ask us to allow you to conduct your recall differently
than specified in this subpart, consistent with section 207(c) of the
Act.
Sec. 1068.510 How do I prepare and apply my remedial plan?
(a) In your remedial plan, describe all of the following:
(1) The class or category of engines to be recalled, including the
number of engines involved and the model year or other information
needed to identify the engines.
(2) The modifications, alterations, repairs, corrections,
adjustments, or other changes you will make to correct the affected
engines.
(3) A brief description of the studies, tests, and data that
support the effectiveness of the remedy you propose to use.
(4) The instructions you will send to those who will repair the
engines under the remedial plan.
(5) How you will determine the owners' names and addresses.
(6) How you will notify owners; include copies of any notification
letters.
(7) The proper maintenance or use you will specify, if any, as a
condition to be eligible for repair under the remedial plan. Describe
how owners should show they meet your conditions.
(8) The steps owners must take for you to do the repair. You may
set a date or a range of dates, specify the amount of time you need,
and designate certain facilities to do the repairs.
(9) Which company (or group) you will assign to do or manage the
repairs.
(10) If your employees or authorized warranty agents will not be
doing the work, state who will and say they can do it.
(11) How you will ensure an adequate and timely supply of parts.
(12) The effect of proposed changes on fuel consumption,
driveability, and safety of the engines you will recall; include a
brief summary of the information supporting these conclusions.
(13) How you intend to label the engines you repair and where you
will place the label on the engine (see Sec. 1068.515).
(b) We may require you to add information to your remedial plan.
(c) We may require you to test the proposed repair to show it will
remedy the noncompliance.
(d) Use all reasonable means to locate owners. We may require you
to use government or commercial registration lists to get owners' names
and addresses, so your notice will be effective.
(e) The maintenance or use that you specify as a condition for
eligibility under the remedial plan may include only things you can
show would cause noncompliance. Do not require use of a component or
service identified by brand, trade, or corporate name, unless we
approved this approach with your original certificate of conformity.
Also, do not place conditions on who maintained the engine.
(f) We may require you to adjust your repair plan if we determine
owners would be without their engines or equipment for an unreasonably
long time.
(g) We will tell you in writing within 15 days of receiving your
remedial plan whether we have approved or disapproved it. We will
explain our reasons for any disapproval.
(h) Begin notifying owners within 15 days after we approve your
remedial plan. If we hold a hearing, but do not change our position
about the noncompliance, you must begin notifying owners within 60 days
after we complete the hearing, unless we specify otherwise.
Sec. 1068.515 How do I mark or label repaired engines?
(a) Attach a label to each engine you repair under the remedial
plan. At your discretion, you may label or mark engines you inspect but
do not repair.
(b) Make the label from a durable material suitable for its planned
location. Make sure no one can remove the label without destroying or
defacing it.
(c) On the label, designate the specific recall campaign and state
where you repaired or inspected the engine.
(d) We may waive or modify the labeling requirements if we
determine they are overly burdensome.
Sec. 1068.520 How do I notify affected owners?
(a) Notify owners by first class mail, unless we say otherwise. We
may require you to use certified mail. Include the following in your
notice:
(1) State: ``The U.S. Environmental Protection Agency has
determined that your engine may be emitting pollutants in excess of the
Federal emission standards, as defined in Title 40 of the Code of
Federal Regulations. These emission standards were established to
protect the public health or welfare from air pollution''.
(2) State that you (or someone you designate) will repair these
engines at your expense.
(3) If we approved maintenance and use conditions in your remedial
plan, state that you will make these repairs only if owners show their
engines meet the conditions for proper maintenance and use. Describe
these conditions and how owners should prove their engines are eligible
for repair.
(4) Describe the components your repair will affect and say
generally how you will repair the engines.
(5) State that the engine, if not repaired, may fail an emission
inspection test if state or local law requires one.
(6) Describe any adverse effects on its performance or driveability
that would be caused by not repairing the engine.
(7) Describe any adverse effects on the functions of other engine
components that would be caused by not repairing the engine.
[[Page 68446]]
(8) Specify the date you will start the repairs, the amount of time
you will need to do them, and where you will do them. Include any other
information owners may need to know.
(9) Include a self-addressed card that owners can mail back if they
have sold the engine (or equipment in which the engine is installed);
include a space for owners to write the name and address of a buyer.
(10) State that owners should call you at a phone number you give
to report any difficulty in obtaining repairs.
(11) State: ``To ensure your full protection under the emission
warranty on your engine by federal law, and your right to participate
in future recalls, we recommend you have your engine serviced as soon
as possible. We may consider your not servicing it to be improper
maintenance''.
(b) We may require you to add information to your notice or to send
more notices.
(c) You may not in any communication with owners or dealers say or
imply that your noncompliance does not exist or that it will not
degrade air quality.
Sec. 1068.525 What records must I send to EPA?
(a) Send us a copy of all communications related to the remedial
plan you sent to dealers and others doing the repairs. Mail or e-mail
us the information at the same time you send it to others.
(b) From the time you begin to notify owners, send us a report
within 25 days of the end of each calendar quarter. Send reports for
six consecutive quarters or until all the engines are inspected,
whichever comes first. In these reports, identify the following:
(1) The range of dates you needed to notify owners.
(2) The total number of notices sent.
(3) The number of engines you estimate fall under the remedial plan
(explain how you determined this number).
(4) The cumulative number of engines you inspected under the
remedial plan.
(5) The cumulative number of these engines you found needed the
specified repair.
(6) The cumulative number of these engines you have repaired.
(7) The cumulative number of engines you determined to be
unavailable due to exportation, theft, retirement, or other reasons
(specify).
(8) The cumulative number of engines you disqualified for not being
properly maintained or used.
(c) If your estimated number of engines falling under the remedial
plan changes, change the estimate in your next report and add an
explanation for the change.
(d) We may ask for more information.
(e) We may waive reporting requirements or adjust the reporting
schedule.
(f) If anyone asks to see the information in your reports, we will
follow the provisions of Sec. 1068.10 for handling confidential
information.
Sec. 1068.530 What records must I keep?
We may review your records at any time, so it is important that you
keep required information readily available. Keep records associated
with your recall campaign for three years after you complete your
remedial plan. Organize and maintain your records as described in this
section.
(a) Keep a paper copy of the written reports described in Sec.
1068.525.
(b) Keep a record of the names and addresses of owners you
notified. For each engine, state whether you did any of the following:
(1) Inspected the engine.
(2) Disqualified the engine for not being properly maintained or
used.
(3) Completed the prescribed repairs.
(c) You may keep the records in paragraph (b) of this section in
any form we can inspect, including computer databases.
Sec. 1068.535 How can I do a voluntary recall for emission-related
problems?
If we have made a determination that a substantial number of
properly maintained and used engines do not conform to the regulations
of this chapter during their useful life, you may not use a voluntary
recall or other alternate means to meet your obligation to remedy the
noncompliance. Thus, this section only applies where you learn that
your engine family does not meet the requirements of this chapter and
we have not made such a determination.
(a) To do a voluntary recall under this section, first send the
Designated Officer a plan, following the guidelines in Sec. 1068.510.
Within 15 days, we will send you our comments on your plan.
(b) Once we approve your plan, start notifying owners and carrying
out the specified repairs.
(c) From the time you start the recall campaign, send us a report
within 25 days of the end of each calendar quarter, following the
guidelines in Sec. 1068.525(b). Send reports for six consecutive
quarters or until all the engines are inspected, whichever comes first.
(d) Keep your reports and the supporting information as described
in Sec. 1068.530.
Sec. 1068.540 What terms do I need to know for this subpart?
The following terms apply to this subpart:
Days means calendar days.
Owner means someone who owns an engine affected by a remedial plan
or someone who owns a piece of equipment that has one of these engines.
Subpart G--Hearings
Sec. 1068.601 What are the procedures for hearings?
If we agree to hold a hearing related to our decision to order a
recall under Sec. 1068.505, we will hold the hearing according to the
provisions of 40 CFR 85.1807. For any other issues, you may request an
informal hearing, as described in 40 CFR 86.1853-01.
Appendix I to Part 1068--Emission-Related Components
This appendix specifies emission-related components that we
refer to for describing such things as emission-related defects or
requirements related to rebuilding engines.
I. Emission-related components include any engine parts related to
the following systems:
1. Air-induction system.
2. Fuel system.
3. Ignition system.
4. Exhaust gas recirculation systems.
II. The following parts are also considered emission-related
components:
1. Aftertreatment devices.
2. Crankcase ventilation valves.
3. Sensors.
4. Electronic control units.
III. Emission-related components also include any other part whose
only purpose is to reduce emissions or whose failure will increase
emissions without significantly degrading engine performance.
IV. We also consider the emission-control information label to be an
emission-related component.
Appendix II to Part 1068--Emission-Related Parameters and
Specifications
This appendix specifies emission-related parameters and
specifications that we refer to for describing such things as
emission-related defects or requirements related to rebuilding
engines.
I. Basic Engine Parameters--Reciprocating Engines.
1. Compression ratio.
2. Type of air aspiration (natural, Roots-blown, supercharged,
turbocharged).
3. Valves (intake and exhaust).
a. Head diameter dimension.
b. Valve lifter or actuator type and valve lash dimension.
4. Camshaft timing.
a. Valve opening--intake exhaust (degrees from top-dead center
or bottom-dead center).
b. Valve closing--intake exhaust (degrees from top-dead center
or bottom-dead center).
[[Page 68447]]
c. Valve overlap (degrees).
5. Ports--two stroke engines (intake and/or exhaust).
a. Flow area.
b. Opening timing (degrees from top-dead center or bottom-dead
center).
c. Closing timing (degrees from top-dead center or bottom-dead
center).
II. Intake Air System.
1. Roots blower/supercharger/turbocharger calibration.
2. Charge air cooling.
a. Type (air-to-air; air-to-liquid).
b. Type of liquid cooling (engine coolant, dedicated cooling
system).
c. Performance.
3. Temperature control system calibration.
4. Maximum allowable inlet air restriction.
III. Fuel System.
1. General.
a. Engine idle speed.
b. Engine idle mixture.
2. Carburetion.
a. Air-fuel flow calibration.
b. Idle mixture.
c. Transient enrichment system calibration.
d. Starting enrichment system calibration.
e. Altitude compensation system calibration.
f. Hot idle compensation system calibration.
3. Fuel injection for spark-ignition engines.
a. Control parameters and calibrations.
b. Idle mixture.
c. Fuel shutoff system calibration.
d. Starting enrichment system calibration.
e. Transient enrichment system calibration.
f. Air-fuel flow calibration.
g. Altitude compensation system calibration.
h. Operating pressure(s).
i. Injector timing calibration.
4. Fuel injection for compression-ignition engines.
a. Control parameters and calibrations.
b. Transient enrichment system calibration.
c. Air-fuel flow calibration.
d. Altitude compensation system calibration.
e. Operating pressure(s).
f. Injector timing calibration.
IV. Ignition System for Spark-ignition Engines.
1. Control parameters and calibration.
2. Initial timing setting.
3. Dwell setting.
4. Altitude compensation system calibration.
5. Spark plug voltage.
V. Engine Cooling System--thermostat calibration.
VI. Exhaust System--maximum allowable back pressure.
VII. System for Controlling Exhaust Emissions.
1. Air injection system.
a. Control parameters and calibrations.
b. Pump flow rate.
2. EGR system.
a. Control parameters and calibrations.
b. EGR valve flow calibration.
3. Catalytic converter system.
a. Active surface area.
b. Volume of catalyst.
c. Conversion efficiency.
4. Backpressure.
VIII. System for Controlling Crankcase Emissions.
1. Control parameters and calibrations.
2. Valve calibrations.
IX. Auxiliary Emission Control Devices (AECD).
1. Control parameters and calibrations.
2. Component calibration(s).
X. System for Controlling Evaporative Emissions.
1. Control parameters and calibrations.
2. Fuel tank.
a. Volume.
b. Pressure and vacuum relief settings.
XI. Warning Systems Related to Emission Controls.
1. Control parameters and calibrations.
2. Component calibrations.
[FR Doc. 02-23801 Filed 11-7-02; 8:45 am]
BILLING CODE 6560-50-P