[Federal Register: April 15, 2003 (Volume 68, Number 72)]
[Proposed Rules]
[Page 18168-18170]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr15ap03-28]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
[[Page 18168]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2002-NM-62-AD]
RIN 2120-AA64
Airworthiness Directives; BAE Systems (Operations) Limited
(Jetstream) Model 4101 Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to all BAE Systems (Operations)
Limited (Jetstream) Model 4101 airplanes. This proposal would require
inspection of the drive trunnion pins for the main landing gear (MLG)
doors to determine the part number of the pins, and corrective action
if necessary. This action is necessary to prevent failure of the MLG
and consequent reduced controllability of the airplane during takeoff
or landing. This action is intended to address the identified unsafe
condition.
DATES: Comments must be received by May 15, 2003.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 2002-NM-62-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9 a.m. and 3 p.m., Monday through Friday, except
Federal holidays. Comments may be submitted via fax to (425) 227-1232.
Comments may also be sent via the Internet using the following address:
9-anm-nprmcomment@faa.gov. Comments sent via fax or the Internet must
contain ``Docket No. 2002-NM-62-AD'' in the subject line and need not
be submitted in triplicate. Comments sent via the Internet as attached
electronic files must be formatted in Microsoft Word 97 for Windows or
ASCII text.
The service information referenced in the proposed rule may be
obtained from British Aerospace Regional Aircraft American Support,
13850 Mclearen Road, Herndon, Virginia 20171. This information may be
examined at the FAA, Transport Airplane Directorate, 1601 Lind Avenue,
SW., Renton, Washington.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-1175, fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this action may be changed in
light of the comments received.
Submit comments using the following format:
[sbull] Organize comments issue-by-issue. For example, discuss a
request to change the compliance time and a request to change the
service bulletin reference as two separate issues.
[sbull] For each issue, state what specific change to the proposed
AD is being requested.
[sbull] Include justification (e.g., reasons or data) for each
request.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this action must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 2002-NM-62-AD.'' The postcard will be date stamped and
returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 2002-NM-62-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
The Civil Aviation Authority (CAA), which is the airworthiness
authority for the United Kingdom, notified the FAA that an unsafe
condition may exist on all BAE Systems (Operations) Limited (Jetstream)
Model 4101 airplanes. The CAA advises that mandatory BAE Systems
(Operations) Limited Service Bulletin J41-32-017 (Modification JM41253)
addressed in British airworthiness directive 002-02-94, introduced new,
crashworthy drive trunnion pins for the main landing gear (MLG) doors.
Some pre-modification pins were modified to the post-modification
standard and installed on MLG units, which were installed on airplanes
in production. However, at overhaul, some MLGs were found to have pins
identified with pre-modification part numbers; those pins may not have
been modified. This condition, if not corrected, could result in
failure of the MLG and consequent reduced controllability of the
airplane during takeoff or landing.
Explanation of Relevant Service Information
BAE Systems (Operations) Limited has issued Service Bulletin J41-
32-080, dated January 24, 2002, which describes procedures for
inspecting the drive trunnion pins for the MLG doors to determine if
the part number (P/N) of the pins is correct. The service bulletin also
describes procedures for replacing any pin having the incorrect or no
P/N with a new, improved pin. Accomplishment of the actions specified
in the service bulletin is intended to adequately address the
identified unsafe condition. The CAA classified this service bulletin
as mandatory and issued British airworthiness directive 007-01-2002 in
[[Page 18169]]
order to assure the continued airworthiness of these airplanes in the
United Kingdom.
FAA's Conclusions
This airplane model is manufactured in the United Kingdom and is
type certificated for operation in the United States under the
provisions of section 21.29 of the Federal Aviation Regulations (14 CFR
21.29) and the applicable bilateral airworthiness agreement. Pursuant
to this bilateral airworthiness agreement, the CAA has kept the FAA
informed of the situation described above. The FAA has examined the
findings of the CAA, reviewed all available information, and determined
that AD action is necessary for products of this type design that are
certificated for operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would require accomplishment of
the actions specified in the service bulletin described previously.
Cost Impact
The FAA estimates that 57 airplanes of U.S. registry would be
affected by this proposed AD, that it would take approximately 2 work
hours per airplane to accomplish the proposed inspection, and that the
average labor rate is $60 per work hour. Based on these figures, the
cost impact of the proposed AD on U.S. operators is estimated to be
$6,840, or $120 per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the proposed requirements of
this AD action, and that no operator would accomplish those actions in
the future if this proposed AD were not adopted. The cost impact
figures discussed in AD rulemaking actions represent only the time
necessary to perform the specific actions actually required by the AD.
These figures typically do not include incidental costs, such as the
time required to gain access and close up, planning time, or time
necessitated by other administrative actions.
Regulatory Impact
The regulations proposed herein would not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this proposal would not have federalism implications
under Executive Order 13132.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
BAE Systems (Operations) Limited (Formerly British Aerospace
Regional Aircraft): Docket 2002-NM-62-AD.
Applicability: All Model Jetstream 4101 airplanes, certificated
in any category.
Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must request approval for an
alternative method of compliance in accordance with paragraph (b) of
this AD. The request should include an assessment of the effect of
the modification, alteration, or repair on the unsafe condition
addressed by this AD; and, if the unsafe condition has not been
eliminated, the request should include specific proposed actions to
address it.
Compliance: Required as indicated, unless accomplished
previously.
To prevent failure of the main landing gear (MLG) and consequent
reduced controllability of the airplane during takeoff or landing,
accomplish the following:
Inspection, and Replacement if Necessary
(a) Within 60 days after the effective date of this AD, perform
a general visual inspection of the drive trunnion pins for the MLG
doors to determine the part number (P/N) of the pins, per ``Part 1--
Inspection'' of the Accomplishment Instructions of BAE Systems
(Operations) Limited Service Bulletin J41-32-080, dated January 24,
2002.
Note 2: For the purposes of this AD, a general visual inspection
is defined as: ``A visual examination of an interior or exterior
area, installation, or assembly to detect obvious damage, failure,
or irregularity. This level of inspection is made from within
touching distance unless otherwise specified. A mirror may be
necessary to enhance visual access to all exposed surfaces in the
inspection area. This level of inspection is made under normally
available lighting conditions such as daylight, hangar lighting,
flashlight, or droplight and may require removal or opening of
access panels or doors. Stands, ladders, or platforms may be
required to gain proximity to the area being checked.''
(1) If P/N AIR135154 is found on both pins: No further action is
required by this paragraph.
(2) If any pin having P/N AIR134402 is found, or if any pin
having no P/N is found: Within 90 days after accomplishing the
inspection, replace the pin having P/N AIR134402 or the pin having
no P/N, with a new, improved pin, per ``Part 2--Rectification'' of
the Accomplishment Instructions of the service bulletin.
Alternative Methods of Compliance
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, International Branch, ANM-116,
Transport Airplane Directorate, FAA. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager, International
Branch, ANM-116.
Note 3: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the International Branch, ANM-116.
Special Flight Permits
(c) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
Note 4: The subject of this AD is addressed in British
airworthiness directive 007-01-2002.
[[Page 18170]]
Issued in Renton, Washington, on April 9, 2003.
Ali Bahrami,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 03-9137 Filed 4-14-03; 8:45 am]
BILLING CODE 4910-13-P