|
U.S. Department of Labor | |
||||
| Occupational Safety & Health Administration | ||||||
 |
|
Standard Interpretations
02/06/2008 - Whether the material storage requirements in 1926.250(a)(1), (b)(6) and (b)(7) apply to stored and stacked brick and masonry blocks that remain completely secured as shipped (interlocked, banded, shrink-wrapped, or similarly bound for shipment) |
Standard Interpretations - Table of Contents |
| • Standard Number: | 1926.250; 1926.250(a)(1); 1926.250(b); 1926.250(b)(6); 1926.250(b)(7) |
February 6, 2008 Mr. Rashod Johnson Director of Engineering Mason Contractors Association of America – MCAA 33 S. Roselle Road Schaumburg, IL 60193 Re: Whether the material storage requirements in 29 CFR 1926.250(a)(1), (b)(6) and (b)(7) apply to stored and stacked brick and masonry blocks that remain completely secured as shipped (interlocked, banded, shrink-wrapped, or similarly bound for shipment)? Dear Mr. Johnson: This is in response to your letter dated January 6, 2006, to the Occupational Safety and Health Administration (OSHA). You ask about the application of certain provisions of Subpart H – Materials Handling, Storage, Use, and Disposal as they relate to the stacking of brick and masonry. We apologize for the long delay in providing this response. We have paraphrased your questions as follows: Question (1): Bricks and masonry blocks are often stored on construction sites as originally shipped. They are shipped in a unit comprising of the following: the bricks or blocks, which are on a pallet, are interlocked, banded, shrink-wrapped, or similarly bound for shipment. Due to jobsite space constraints, these shipping units may be stored two or three pallets high. Does Section 1926.250(a)(1) apply to the stacking of such shipping units? Answer: Section 1926.250(a)(1) provides: All materials stored in tiers shall be stacked, racked, blocked, interlocked or otherwise secured to prevent sliding, falling, or collapse. [Emphasis added]Section 1926.250(a)(1) governs "[a]ll materials stored in tiers." Specifically, it sets forth the intent of the standard ("to prevent sliding, falling, or collapse" of all materials) and direction on how to meet its requirement ("stacked, racked, blocked, interlocked, or otherwise secured"). Since this requirement covers all materials that are tiered, the provision applies to the above-described shipping units of bricks and blocks. It should be noted, however, that while the standard lists several methods by which materials can be stored, the list is not exclusive. Thus, as long as the method of storing these materials in tiers is similarly effective for preventing sliding, falling, or collapse to the methods listed, the method would comply with this provision.1 Specifically, shrink-wrapping or banding the bricks or blocks and stacking the palleted units in a manner that is adequate for flatbed shipping typically would qualify as "otherwise secured to prevent sliding, falling, or collapse."2 Question (2): It has been suggested that these tiered units must be tapered pursuant to Section 1926.250(b)(6) and (b)(7). Do the tapering requirements in these provisions apply to the above-described tiered units? Answer: Section 1926.250(b)(6) provides: Brick stacks shall not be more than 7 feet in height. When a loose brick stack reaches a height of 4 feet, it shall be tapered back 2 inches in every foot of height above the 4-foot level.Section 1926.250(b)(7) states: When masonry blocks are stacked higher than 6 feet, the stack shall be tapered back one-half block per tier above the 6-foot level.By their terms, both Sections 1926.250(b)(6) and 1926.250(b)(7) apply a tapering requirement to stacks of bricks or block; they do not, however, refer to the use of securing methods that use a fundamentally different system of preventing the material from becoming unstable and sliding, falling, or collapsing. When stacking individual bricks or blocks, it is the arrangement of the material that secures each brick or block and prevents both individual pieces and the entire pile from sliding, falling, or collapsing. Stacks are prone to instability once the height limits in those provisions are exceeded. The specified tapering addresses that problem. In contrast, a unit of material properly prepared for transportation, such as a unit that is adequately shrink-wrapped and on a suitable pallet, is secured by a combination of the evenness of the arrangement of the individual pieces, the wrapping of the unit and the stability provided by the pallet. Consequently, these provisions do not apply when the requirements of 1926.250(a)(1) are met by other methods. If you need additional information, please contact us by fax at: U.S. Department of Labor, OSHA, Directorate of Construction, Office of Construction Standards and Guidance, fax # 202-693-1689. You can also contact us by mail at the above office, Room N3468, 200 Constitution Avenue, N.W., Washington, D.C. 20210, although there will be a delay in our receiving correspondence by mail. Sincerely, Steven F. Witt, Director Directorate of Construction 1Any more specific provisions under 1926.250(b) that are applicable would also need to be complied with. [ back to text ] 2Factors that could affect the stability of the tiers, such as an uneven or sloped storage surface or damaged pallets, must be considered when stacking such units to ensure that the requirements of this provision are met. Also, if the number of tiers of such units is such that their stability is imperiled, the employer would not be in compliance with 1926.250(a)(1). [ back to text ] |
|
Standard Interpretations - Table of Contents |
 Back to Top |
www.osha.gov | www.dol.gov |
Contact Us | Freedom of Information Act | Customer Survey Privacy and Security Statement | Disclaimers |
||
| Occupational Safety & Health Administration 200 Constitution Avenue, NW Washington, DC 20210 |
||
