(b) Roof bolts and accessories not addressed in ASTM F432-95 may be used, provided that the use of such materials is approved by the District Manager based on
(1) Demonstrations which show that the materials have
successfully supported the roof in an area of a coal mine with similar
strata, opening dimensions and roof stresses; or
(2) Tests which show the materials to be effective for
supporting the roof in an area of the affected mine which has similar strata,
opening dimensions and roof stresses as the area where the roof bolts are to
be used. During the test process, access to the test area shall be limited to
persons necessary to conduct the test.
(c)(1) A bearing plate shall be firmly installed with each roof
bolt.
(2) Bearing plates used directly against the mine roof
shall be at least 6 inches square or the equivalent, except that where the
mine roof is firm and not susceptible to sloughing, bearing plates 5 inches
square or the equivalent may be used.
(3) Bearing plates used with wood or metal materials shall
be at least 4 inches square or the equivalent.
(4) Wooden materials that are used between a bearing plate
and the mine roof in areas which will exist for three years or more shall be
treated to minimize deterioration.
(d) When washers are used with roof bolts, the washers shall conform
to the shape of the roof bolt head and bearing plate.
(e)(1) The diameter of finishing bits shall be within a tolerance of
plus or minus 0.030 inch of the manufacturer's recommended hole diameter for
the anchor used.
(2) When separate finishing bits are used, they shall be
distinguishable from other bits.
(f) Tensioned roof bolts. (1) Roof bolts that provide support
by creating a beam of laminated strata shall be at least 30 inches long. Roof
bolts that provide support by suspending the roof from overlying stronger
strata shall be long enough to anchor at least 12 inches into the stronger
strata.
(2) Test holes, spaced at intervals specified in the roof
control plan, shall be drilled to a depth of at least 12 inches above the
anchorage horizon of mechanically anchored tensioned bolts being used. When a
test hole indicates that bolts would not anchor in competent strata,
corrective action shall be taken.
(3) The installed torque or tension ranges for roof bolts
as specified in the roof control plan shall maintain the integrity of the
support system and shall not exceed the yield point of the roof bolt nor
anchorage capacity of the strata.
(4) In each roof bolting cycle, the actual torque or
tension of the first tensioned roof bolt installed with each drill head shall
be measured immediately after it is installed. Thereafter, for each drill
head used, at least one roof bolt out of every four installed shall be
measured for actual torque or tension. If the torque or tension of any of the
roof bolts measured is not within the range specified in the roof control
plan, corrective action shall be taken.
(5) In working places from which coal is produced during
any portion of a 24-hour period, the actual torque or tension on at least one
out of every ten previously installed mechanically anchored tensioned roof
bolts shall be measured from the outby corner of the last open crosscut to
the face in each advancing section. Corrective action shall be taken if the
majority of the bolts measured--
(f)(5)(i) Do not maintain at least 70 percent of the minimum
torque or tension specified in the roof control plan, 50 percent if the roof
bolt plates bear against wood; or
(f)(5)(ii) Have exceeded the maximum specified torque or tension
by 50 percent.
(6) The mine operator or a person designated by the
operator shall certify by signature and date that measurements required by
paragraph (f)(5) of this section have been made. This certification shall be
maintained for at least one year and shall be made available to an authorized
representative of the Secretary and representatives of the miners.
(7) Tensioned roof bolts installed in the roof support
pattern shall not be used to anchor trailing cables or used for any other
purpose that could affect the tension of the bolt. Hanging trailing cables,
line brattice, telephone lines, or other similar devices which do not place
sudden loads on the bolts are permitted.
(8) Angle compensating devices shall be used to compensate
for the angle when tensioned roof bolts are installed at angles greater than
5 degrees from the perpendicular to the bearing plate.
(g) Non-tensioned grouted roof bolts. The first non-tensioned
grouted roof bolt installed during each roof bolting cycle shall be tested
during or immediately after the first row of bolts has been installed. If the
bolt tested does not withstand at least 150 foot-pounds of torque without
rotating in the hole, corrective action shall be taken.
[53 FR 2375, Jan. 27, 1988, as amended at 55 FR 4595, Feb. 8, 1990, Apr. 22, 1998]