U.S. Department of Labor | ||||||
Occupational Safety & Health Administration |
Excavations U.S. Department of Labor Elaine L. Chao, Secretary Occupational Safety and Health Administration John L. Henshaw, Assistant Secretary OSHA 2226 2002 (Revised) Contents Introduction What is the difference between an excavation and a trench? What are the dangers of trenching and excavation operation? OSHA's Excavation and Trenching Standard What does the OSHA standard cover, and what protections does it offer? What kinds of excavations and trenches are not covered? Preplanning Why is it important to preplan the excavation work? What safety factors should you consider when bidding on a job? How can you avoid hitting underground utility lines and pipes during excavation work? What should you tell workers before they start the project? Protective Systems How can you prevent cave-ins? How do you choose the most appropriate protective system design? What other safety precautions are you required to take? How do you safely install and remove protective systems? How should you maintain materials and equipment used for protective systems? Additional Hazards and Protections What other excavation hazards do you need to protect workers against? What is the effect of water accumulation on excavation safety? How can you protect workers against hazardous atmospheres inside excavations? What means of access and egress are you required to provide? What protective equipment are employees in pier holes and confined footing excavations required to use? When should you conduct a site inspection? OSHA Assistance, Services, and Programs How can OSHA help me? How does safety and health program management assistance help employers and employees? What are state plans? How can consultation assistance help employers? Who can get consultation assistance and what does it cost? Can OSHA assure privacy to an employer who asks for consultation assistance? Can an employer be cited for violations after receiving consultation assistance? Does OSHA provide any incentives for seeking consultation assistance? What are the Voluntary Protection Programs (VPP)? How do the VPP work? How do VPP help employers and employees? How does OSHA monitor VPP sites? Can OSHA inspect an employer who is participating in the VPP? How can a partnership with OSHA improve worker safety and health? What is OSHA's Strategic Partnership Program (OSPP)? What do OSPPs do? What are the different kinds of OSPPs? What are the benefits of participation in the OSPP? Does OSHA have occupational safety and health training for employers and employees? Does OSHA give money to organizations for training and education? Does OSHA have other assistance materials available? What do I do in case of any emergency or if I need to file a complaint? OSHA Regional and Area Offices OSHA-Approved Safety and Health Plans OSHA Onsite Consultation Offices Introduction Excavation and trenching are among the most hazardous construction operations. The Occupational Safety and Health Administration's (OSHA) Excavation and Trenching standard, Title 29 of the Code of Federal Regulation (CFR), Part 1926.650, covers requirements for excavation and trenching operations. This booklet highlights key elements of the standard, shows ways to protect employees against cave-ins, and describes safe work practices for employees. What is the difference between an excavation and a trench? OSHA defines an excavation as any man-made cut, cavity, trench, or depression in the earth's surface formed by earth removal. This can include excavations for anything from cellars to highways. A trench is defined as a narrow underground excavation that is deeper than it is wide, and no wider than 15 feet (4.5 meters). What are the dangers of trenching and excavation operations? Trenching and excavation work presents serious hazards to all workers involved. Cave-ins pose the greatest risk and are much more likely than other excavation-related accidents to result in worker fatalities. Other potential hazards include falls, falling loads, hazardous atmospheres, and incidents involving mobile equipment. OSHA's Excavation and Trenching Standard What does the OSHA standard cover, and what protections does it offer? The rule applies to all open excavations made in the earth's surface, including trenches. Strict compliance with all sections of the standard will prevent or greatly reduce the risk of cave-ins as well as other excavation-related accidents. What kinds of excavations and trenches are not covered? The standard does not apply to house foundation/ basement excavations, including those that become trenches by definition when constructing formwork, foundations, or walls. For this exemption to apply, all the following conditions must exist:
Preplanning Why is it important to preplan the excavation work? No matter how many trenching, shoring, and backfilling jobs you have done in the past, it is important to approach each new job with the utmost care and preparation. Many on-the-job accidents result directly from inadequate initial planning. Waiting until after the work has started to correct mistakes in shoring or sloping slows down the operation, adds to the cost, and increases the possibility of a cave-in or other excavation failure. What safety factors should you consider when bidding on a job? Before preparing a bid, you will want to know as much as possible about the jobsite and the materials you will need to have on hand to perform the work safely and in compliance with OSHA standards. A safety checklist may prove helpful when you consider specific site conditions such as the following:
How can you avoid hitting underground utility lines and pipes during excavation work? Before starting work, the OSHA standard requires you to do the following:
What should you tell workers before they start the project? When you share the details of your safety and health program with employees, it is important to emphasize the critical role you expect them to play in keeping the jobsite safe. You may want to emphasize specific rules to help reduce the risk of on-the-job injuries. These rules may include requirements that workers
Protective Systems How can you prevent cave-ins? OSHA requires that all excavations in which employees could potentially be exposed to cave-ins be protected by
Designing a protective system can be complex because you must consider many factors: soil classification, depth of cut, water content of soil, changes due to weather and climate, or other operations in the vicinity. You are free to choose the most practical design approach for any particular circumstance. Once you have selected an approach, however, the system must meet the required performance criteria. The OSHA standard describes methods and approaches for designing protective systems such as the following: Method 1 — Slope the sides to an angle not steeper than 1-1/2:1; for example, for every foot of depth, the trench must be excavated back 1-1/2 feet. All simple slope excavations 20 feet (6.11 meters) or less deep should have a maximum allowable slope of 1-1/2:1. These slopes must be excavated to form configurations similar to those for Type C soil, as described in Appendix B of the standard. A slope of this gradation or less is safe for any type of soil. Figure 1. Excavations Made in Type C Soil Method 2 — Use tabulated data such as tables and charts approved by a registered professional engineer to design excavation. These data must be in writing and must include enough explanatory information, including the criteria for making a selection and the limits on the use of the data, for the user to make a selection. At least one copy of the data, including the identity of the registered professional engineer who approved it, must be kept at the worksite during construction of the protective system. After the system is completed, the data may be stored away from the jobsite, but a copy must be provided upon request to the Assistant Secretary of Labor for OSHA. Method 3 — Use a trench box or shield designed or approved by a registered professional engineer or based on tabulated data prepared or approved by a registered professional engineer. Timber, aluminum, or other suitable materials may also be used. OSHA standards permit the use of a trench shield (also known as a welder’s hut) if it provides the same level of protection or more than the appropriate shoring system. Figure 2. Trench Shields Employers can choose the most practical method for the particular circumstance, but that system must meet the required performance criteria. The standard does not require a protective system when an excavation is made entirely in stable rock or is less than 5 feet (1.52 meters) deep, if a competent person has examined the ground and found no indication of a potential cave-in. What other safety precautions are you required to take? The standard requires you to provide support systems such as shoring, bracing, or underpinning to ensure that adjacent structures such as buildings, walls, sidewalks, or pavements remain stable. The standard also prohibits excavation below the base or footing of any foundation or retaining wall unless
As soon as work is completed, you are required to backfill the excavation when you dismantle the protective system. After the excavation is cleared, remove the protective system from the bottom up, taking care to release members slowly. How should you maintain materials and equipment used for protective systems? You are responsible for maintaining materials and equipment used for protective systems. Defective and damaged materials and equipment can cause failure of a protective system and other excavation hazards. To avoid possible failure of a protective system, you must ensure that
Additional Hazards and Protections What other excavation hazards do you need to protect workers against? In addition to cave-ins and related hazards, workers involved in excavation work also are exposed to hazards involving falls, falling loads, and mobile equipment. To protect employees from these hazards, OSHA requires you to take the following precautions:
Among the additional hazards stemming from water in an excavation are undermining the sides and making it more difficult to get out of the excavation. The OSHA standard prohibits employees from working without adequate protection in excavations where water has accumulated or is accumulating. If you use water removal equipment to control or prevent water accumulation, you must ensure that a competent person monitors the equipment and its operation to ensure proper use. OSHA standards also require the use of diversion ditches, dikes, or other suitable means to prevent surface water from entering an excavation and to provide adequate drainage of the adjacent area. In addition, a competent person must inspect excavations subject to runoffs from heavy rains. How can you protect workers against hazardous atmospheres inside excavations? A competent person must test any excavation deeper than 4 feet (1.22 meters) or where an oxygen deficiency or a hazardous atmosphere is present or could reasonably be expected, such as a landfill or where hazardous substances are stored nearby, before an employee enters it. If there are any hazardous conditions, you must provide the employee controls such as proper respiratory protection or ventilation. In addition, you are responsible for regularly testing all controls used to reduce atmospheric contaminants to acceptable levels. If unhealthful atmospheric conditions exist or develop in an excavation, you must provide emergency rescue equipment such as a breathing apparatus, safety harness and line, and basket stretcher and ensure that it is readily available. This equipment must be attended when in use. What means of access and egress are you required to provide? OSHA requires you to provide safe access and egress to all excavations, including ladders, steps, ramps, or other safe means of exit for employees working in trench excavations 4 feet (1.22 meters) or deeper. These devices must be located in the excavation within 25 feet (7.62 meters) of all workers. Any structural ramps you use in your operation must be designed by a competent person if they are used for employee access or egress, or by a competent person qualified in structural design if they are used for vehicles. Also, structural members used for ramps or runways must be uniform in thickness and joined in a manner to prevent tripping or displacement. What protective equipment are employees in pier holes and confined footing excavations required to use? An employee who enters a bell-bottom pier hole or similar deep and confined footing excavation must wear a harness with a lifeline. The lifeline must be attached securely to the harness and must be separate from any line used to handle materials. Also, while the employee wearing the lifeline is in the excavation, an observer must be on hand to ensure that the lifeline is working properly and maintain communication with the employee. When should you conduct a site inspection? The standard requires that a competent person inspect an excavation and the areas around it daily for possible cave-ins, failures of protective systems and equipment, hazardous atmospheres, or other hazardous conditions. Inspections also are required after natural events such as heavy rains or manmade events such as blasting that may increase the potential for hazards. If the inspector finds any unsafe conditions during an inspection, you must clear employees from the hazardous area until you take safety precautions. The standard also requires that a competent person inspect excavations and the adjacent areas daily for possible cave-ins, failures of protective systems and equipment, hazardous atmospheres, and other hazardous conditions. If the competent person finds these conditions, all exposed employees must leave the hazardous area until necessary safety precautions are taken. Larger and more complex operations should have a full-time safety official who makes recommendations to improve implementation of the safety plan. In a smaller operation, the safety official may be part-time and usually will be a supervisor. Supervisors are the contractor's representatives on the job. Supervisors should conduct inspections, investigate accidents, and anticipate hazards. They should ensure that employees receive on-the-job safety and health training. They also should review and strengthen overall safety and health precautions to guard against potential hazards, get the necessary worker cooperation in safety matters, and make frequent reports to the contractor. OSHA Assistance, Services, and Programs How can OSHA help me? OSHA can provide extensive help through a variety of programs, including assistance about safety and health programs, state plans, workplace consultations, Voluntary Protection Programs, strategic partnerships, training and education, and more. How does safety and health program management help employers and employees? Effective management of worker safety and health protection is a decisive factor in reducing the extent and severity of work-related injuries and illnesses and their related costs. In fact, an effective safety and health management system forms the basis of good worker protection and can save time and money—about $4 for every dollar spent—and increase productivity. To assist employers and employees in developing effective safety and health programs, OSHA published recommended Safety and Health Program Management Guidelines (Federal Register 54(18):3904-3916, January 26, 1989). These voluntary guidelines can be applied to all worksites covered by OSHA. The guidelines identify four general elements critical to the development of a successful safety and health management program:
What are state plans? State plans are OSHA-approved job safety and health programs operated by individual states or territories instead of Federal OSHA. The Occupational Safety and Health Act of 1970 (OSH Act) encourages states to develop and operate their own job safety and health plans and permits state enforcement of OSHA standards if the state has an approved plan. Once OSHA approves a state plan, it funds 50 percent of the program's operating costs. State plans must provide standards and enforcement programs, as well as voluntary compliance activities, that are at least as effective as those of Federal OSHA. There are 26 state plans: 23 cover both private and public (state and local government) employment, and 3 (Connecticut, New Jersey, and New York) cover only the public sector. For more information on state plans, see the listing at the end of this publication, or visit OSHA's website at www.osha.gov. How can consultation assistance help employers? In addition to helping employers identify and correct specific hazards, OSHA's consultation service provides free, onsite assistance in developing and implementing effective workplace safety and health management systems that emphasize the prevention of worker injuries and illnesses. Comprehensive consultation assistance provided by OSHA includes a hazard survey of the worksite and an appraisal of all aspects of the employer's existing safety and health management system. In addition, the service offers assistance to employers in developing and implementing an effective safety and health management system. Employers also may receive training and education services, as well as limited assistance away from the worksite. Who can get consultation assistance and what does it cost? Consultation assistance is available to small employers (with fewer than 250 employees at a fixed site and no more than 500 corporatewide) who want help in establishing and maintaining a safe and healthful workplace. Funded largely by OSHA, the service is provided at no cost to the employer. Primarily developed for smaller employers with more hazardous operations, the consultation service is delivered by state governments employing professional safety and health consultants. No penalties are proposed or citations issued for hazards identified by the consultant. The employer's only obligation is to correct all identified serious hazards within the agreed-upon correction time frame. Can OSHA assure privacy to an employer who asks for consultation assistance? OSHA provides consultation assistance to the employer with the assurance that his or her name and firm and any information about the workplace will not be routinely reported to OSHA enforcement staff. Can an employer be cited for violations after receiving consultation assistance? If an employer fails to eliminate or control a serious hazard within the agreed-upon time frame, the consultation project manager must refer the situation to the OSHA enforcement office for appropriate action. This is a rare occurrence, however, since employers request the service for the expressed purpose of identifying and fixing hazards in their workplaces. Does OSHA provide any incentives for seeking consultation assistance? Yes. Under the consultation program, certain exemplary employers may request participation in OSHA's Safety and Health Achievement Recognition Program (SHARP). Eligibility for participation in SHARP includes, but is not limited to, receiving a full-service, comprehensive consultation visit, correcting all identified hazards, and developing an effective safety and health management system. Employers accepted into SHARP may receive an exemption from programmed inspections (not complaint or accident investigation inspections) for a period of 1 year initially, or 2 years upon renewal. For more information concerning consultation assistance, see the list of consultation offices beginning on page 42, contact your regional or area OSHA office, or visit OSHA's website at www.osha.gov. What are the Voluntary Protection Programs? Voluntary Protection Programs (VPPs) represent one part of OSHA's effort to extend worker protection beyond the minimum required by OSHA standards. VPP—along with onsite consultation services, full-service area offices, and OSHA's Strategic Partnership Program (OSPP)— represents a cooperative approach which, when coupled with an effective enforcement program, expands worker protection to help meet the goals of the OSH Act. How do the VPP work? There are three levels of VPPs: Star, Merit, and Demonstration. All are designed to do the following:
VPP participation can mean the following:
OSHA reviews an employer's VPP application and conducts a VPP Onsite Evaluation to verify that the safety and health management systems described are operating effectively at the site. OSHA conducts onsite evaluations on a regular basis, annually for participants at the Demonstration level, every 18 months for Merit, and every 3 to 5 years for Star. Each February, all participants must send a copy of their most recent annual evaluation to their OSHA regional office. This evaluation must include the worksite's record of injuries and illnesses for the past year. Can OSHA inspect an employer who is participating in the VPP? Sites participating in VPP are not scheduled for regular, programmed inspections. OSHA handles any employee complaints, serious accidents, or significant chemical releases that may occur at VPP sites according to routine enforcement procedures. Additional information on VPP is available from OSHA national, regional, and area offices, listed beginning on page 31. Also, see Outreach on OSHA's website at www.osha.gov. How can a partnership with OSHA improve worker safety and health? OSHA has learned firsthand that voluntary, cooperative partnerships with employers, employees, and unions can be a useful alternative to traditional enforcement and an effective way to reduce worker deaths, injuries, and illnesses. This is especially true when a partnership leads to the development and implementation of a comprehensive workplace safety and health management system. What is OSHA's Strategic Partnership Program (OSPP)? OSHA Strategic Partnerships are alliances among labor, management, and government to foster improvements in workplace safety and health. These partnerships are voluntary, cooperative relationships between OSHA, employers, employee representatives, and others such as trade unions, trade and professional associations, universities, and other government agencies. OSPPs are the newest of OSHA's cooperative programs. What do OSPPs do? These partnerships encourage, assist, and recognize the efforts of the partners to eliminate serious workplace hazards and achieve a high level of worker safety and health. Whereas OSHA's Consultation Program and VPP entail one-on-one relationships between OSHA and individual worksites, most strategic partnerships seek to have a broader impact by building cooperative relationships with groups of employers and employees. What are the different kinds of OSPPs? There are two major types:
What are the benefits of participation in the OSPP? Like VPP, OSPP can mean the following:
Does OSHA have occupational safety and health training for employers and employees? The OSHA Training Institute in Des Plaines, IL, provides basic and advanced training and education in safety and health for federal and state compliance officers, state consultants, other federal agency personnel, and private-sector employers, employees, and their representatives. Institute courses cover diverse safety and health topics including electrical hazards, machine guarding, personal protective equipment, ventilation, and ergonomics. The facility includes classrooms, laboratories, a library, and an audiovisual unit. The laboratories contain various demonstrations and equipment, such as power presses, woodworking and welding shops, a complete industrial ventilation unit, and a sound demonstration laboratory. More than 57 courses dealing with subjects such as safety and health in the construction industry and methods of compliance with OSHA standards are available for personnel in the private sector. In addition, OSHA's 73 area offices are full-service centers offering a variety of informational services such as personnel for speaking engagements, publications, audiovisual aids on workplace hazards, and technical advice. For more information on grants, training, and education, write: OSHA Training Institute, Office of Training and Education, 1555 Times Drive, Des Plaines, IL 60018; call (847) 297-4810; or see Outreach on OSHA's website at www.osha.gov. Does OSHA give money to organizations for training and education? OSHA awards grants through its Susan Harwood Training Grant Program to nonprofit organizations to provide safety and health training and education to employers and workers in the workplace. The grants focus on programs that will educate workers and employers in small business (fewer than 250 employees), training workers and employers about new OSHA standards or about high-risk activities or hazards. Grants are awarded for 1 year and may be renewed for an additional 12 months depending on whether the grantee has performed satisfactorily. OSHA expects each organization awarded a grant to develop a training and/or education program that addresses a safety and health topic named by OSHA, recruit workers and employers for the training, and conduct the training. Grantees are also expected to follow up with people who have been trained to find out what changes were made to reduce the hazards in their workplaces as a result of the training. Each year OSHA has a national competition that is announced in the Federal Register and on the Internet at www.osha.gov/Training/sharwood/sharwood.html. If you do not have access to the Internet, you can contact the OSHA Office of Training and Education, 1555 Times Drive, Des Plaines, IL 60018, (847) 297-4810, for more information. Does OSHA have other assistance materials available? OSHA has a variety of materials and tools available on its website at www.osha.gov. These include eTools, Expert Advisors, Electronic Compliance Assistance Tools (e-CATs), Technical Links, regulations, directives, publications, videos, and other information for employers and employees. OSHA's software programs and compliance assistance tools walk you through challenging safety and health issues and common problems to find the best solutions for your workplace. OSHA's comprehensive publications program includes more than 100 titles to help you understand OSHA requirements and programs. OSHA's CD-ROM includes standards, interpretations, directives, and more and can be purchased on CD-ROM from the U.S. Government Printing Office. To order, write to the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, or phone (202) 512-1800. Specify OSHA Regulations, Documents and Technical Information on CD-ROM (ORDT), GPO Order No. S/N 729-013-00000-5. What do I do in case of an emergency or if I need to file a complaint? To report an emergency, file a complaint, or seek OSHA advice, assistance, or products, call (800) 321-OSHA or contact your nearest OSHA regional or area office listed at the end of this publication. The teletypewriter (TTY) number is (877) 889-5627. You can also file a complaint online and obtain more information on OSHA federal and state programs by visiting OSHA's website at www.osha.gov. OSHA Regional and Area Offices OSHA Regional Offices Region I (CT,* ME, MA, NH, RI, VT*) JFK Federal Building, Room E340 Boston, MA 02203 (617) 565-9860 Region II (NJ,* NY,* PR,* VI*) 201 Varick Street, Room 670 New York, NY 10014 (212) 337-2378 Region III (DE, DC, MD,* PA,* VA,* WV) The Curtis Center 170 S. Independence Mall West Suite 740 West Philadelphia, PA 19106-3309 (215) 861-4900 Region IV (AL, FL, GA, KY,* MS, NC,* SC,* TN*) SNAF 61 Forsyth Street SW Room 6T50 Atlanta, GA 30303 (404) 562-2300 Region V (IL, IN,* MI,* MN,* OH, WI) 230 South Dearborn Street, Room 3244 Chicago, IL 60604 (312) 353-2220 Region VI (AR, LA, NM,* OK, TX) 525 Griffin Street, Room 602 Dallas, TX 75202 (214) 767-4731 or 4736 x224 Region VII (IA,* KS, MO, NE) City Center Square 1100 Main Street, Suite 800 Kansas City, MO 64105 (816) 426-5861 Region VIII (CO, MT, ND, SD, UT,* WY*) 1999 Broadway, Suite 1690 PO Box 46550 Denver, CO 80202-5716 (303) 844-1600 Region IX (American Samoa, AZ,* CA,* HI, NV,* Northern Mariana Islands) 71 Stevenson Street, Room 420 San Francisco, CA 94105 (415) 975-4310 Region X (AK,* ID, OR,* WA*) 1111 Third Avenue, Suite 715 Seattle, WA 98101-3212 (206) 553-5930 *These states and territories operate their own OSHA-approved job safety and health programs (Connecticut, New Jersey and New York plans cover public employees only). States with approved programs must have a standard that is identical to, or at least as effective as, the federal standard. OSHA Area Offices Anchorage, AK (907) 271-5152 Birmingham, AL (205) 731-1534 Mobile, AL (334) 441-6131 Little Rock, AR (501) 324-6291 (5818) Phoenix, AZ (602) 640-2348 Sacramento, CA (916) 566-7471 San Diego, CA (619) 557-5909 Denver, CO (303) 844-5285 Englewood, CO (303) 843-4500 Bridgeport, CT (203) 579-5581 Hartford, CT (860) 240-3152 Wilmington, DE (302) 573-6518 Fort Lauderdale, FL (954) 424-0242 Jacksonville, FL (904) 232-2895 Tampa, FL (813) 626-1177 Savannah, GA (912) 652-4393 Smyrna, GA (770) 984-8700 Tucker, GA (770) 493-6644/6742/8419 Des Moines, IA (515) 284-4794 Boise, ID (208) 321-2960 Calumet City, IL (708) 891-3800 Des Plaines, IL (847) 803-4800 Fairview Heights, IL (618) 632-8612 North Aurora, IL (630) 896-8700 Peoria, IL (309) 671-7033 Indianapolis, IN (317) 226-7290 Wichita, KS (316) 269-6644 Frankfort, KY (502) 227-7024 Baton Rouge, LA (225) 389-0474 (0431) Braintree, MA (617) 565-6924 Methuen, MA (617) 565-8110 Springfield, MA (413) 785-0123 Linthicum, MD (410) 865-2055/2056 August, ME (207) 622-8417 Bangor, ME (207) 941-8177 Portland, ME (207) 780-3178 Lansing, MI (517) 327-0904 Minneapolis, MN (612) 664-5460 Kansas City, MO (816) 483-9531 St. Louis, MO (314) 425-4289 Jackson, MS (601) 965-4606 Billings, MT (406) 247-7494 Raleigh, NC (919) 856-4770 Bismark, ND (701) 250-4521 Omaha, NE (402) 221-3182 Concord, NH (603) 225-1629 Avenel, NJ (732) 750-3270 Hasbrouck Heights, NJ (201) 288-1700 Marlton, NJ (609) 757-5181 Parsippany, NJ (973) 263-1003 Albuquerque, NM (505) 248-5302 Carson City, NV (775) 885-6963 Albany, NY (518) 464-4338 Bayside, NY (718) 279-9060 Bowmansville, NY (716) 684-3891 New York, NY (212) 466-2482 North Syracuse, NY (315) 451-0808 Tarrytown, NY (914) 524-7510 Westbury, NY (516) 334-3344 Cincinnati, OH (513) 841-4132 Cleveland, OH (216) 522-3818 Columbus, OH (614) 469-5582 Toledo, OH (419) 259-7542 Oklahoma City, OK (405) 231-5351 (5389) Portland, OR (503) 326-2251 Allentown, PA (610) 776-0592 Erie, PA (814) 833-5758 Harrisburg, PA (717) 782-3902 Philadelphia, PA (215) 597-4955 Pittsburgh, PA (412) 395-4903 Wilkes-Barre, PA (570) 826-6538 Guaynabo, PR (787) 277-1560 Providence, RI (401) 528-4669 Columbia, SC (803) 765-5904 Nashville, TN (615) 781-5423 Austin, TX (512) 916-5783 (5788) Corpus Christi, TX (512) 888-3420 Dallas, TX (214) 320-2400 (2558) El Paso, TX (915) 534-6251 Fort Worth, TX (817) 428-2470 (485-7647) Houston, TX (281) 591-2438 (2787) Houston, TX (281) 286-0583/0584 (5922) Lubbock, TX (806) 472-7681 (7685) Salt Lake City, UT (801) 530-6901 Norfolk, VA (757) 441-3820 Bellevue, WA (206) 553-7520 Appleton, WI (920) 734-4521 Eau Claire, WI (715) 832-9019 Madison, WI (608) 264-5388 Milwaukee, WI (414) 297-3315 Charleston, WV (304) 347-5937 OSHA-Approved Safety and Health Plans Alaska Alaska Department of Labor and Workforce Development Commissioner (907) 465-2700 FAX: (907) 465-2784 Program Director (907) 269-4904 FAX: (907) 269-4915 Arizona Industrial Commission of Arizona Director, ICA (602) 542-4411 FAX: (602) 542-1614 Program Director (602) 542-5795 FAX: (602) 542-1614 California California Department of Industrial Relations Director (415) 703-5050 FAX: (415) 703-5114 Chief (415) 703-5100 FAX: (415) 703-5114 Manager, Cal/OSHA Program Office (415) 703-5177 FAX: (415) 703-5114 Connecticut Connecticut Department of Labor Commissioner (860) 566-5123 FAX: (860) 566-1520 Conn-OSHA Director (860) 566-4550 FAX: (860) 566-6916 Hawaii Hawaii Department of Labor and Industrial Relations Director (808) 586-8844 FAX: (808) 586-9099 Administrator (808) 586-9116 FAX: (808) 586-9104 Indiana Commissioner (317) 232-2378 FAX: (317) 233-3790 Deputy Commissioner (317) 232-3325 FAX: (317) 233-3790 Iowa Iowa Division of Labor Commissioner (515) 281-6432 FAX: (515) 281-4698 Administrator (515) 281-3469 FAX: (515) 281-7995 Kentucky Kentucky Labor Cabinet Secretary (502) 564-3070 FAX: (502) 564-5387 Federal\State Coordinator (502) 564-3070 ext.240 FAX: (502) 564-1682 Maryland Maryland Division of Labor and Industry Commissioner (410) 767-2999 FAX: (410) 767-2300 Deputy Commissioner (410) 767-2992 FAX: (410) 767-2003 Assistant Commissioner, MOSH (410) 767-2215 FAX: (410) 767-2003 Michigan Michigan Department of Consumer and Industry Services Director (517) 322-1814 FAX: (517) 322-1775 Minnesota Minnesota Department of Labor and Industry Commissioner (651) 296-2342 FAX: (651) 282-5405 Assistant Commissioner (651) 296-6529 FAX: (651) 282-5293 Administrative Director, OSHA Management Team (651) 282-5772 FAX: (651) 297-2527 Nevada Nevada Division of Industrial Relations Administrator (775) 687-3032 FAX: (775) 687-6305 Chief Administrative Officer (702) 486-9044 FAX: (702) 990-0358 [Las Vegas (702) 687-5240] New Jersey New Jersey Department of Labor Commissioner (609) 292-2975 FAX: (609) 633-9271 Assistant Commissioner (609) 292-2313 FAX: (609) 292-1314 Program Director, PEOSH (609) 292-3923 FAX: (609) 292-4409 New Mexico New Mexico Environment Department Secretary (505) 827-2850 FAX: (505) 827-2836 Chief (505) 827-4230 FAX: (505) 827-4422 New York New York Department of Labor Acting Commissioner (518) 457-2741 FAX: (518) 457-6908 Division Director (518) 457-3518 FAX: (518) 457-6908 North Carolina North Carolina Department of Labor Commissioner (919) 807-2900 FAX: (919) 807-2855 Deputy Commissioner, OSH Director (919) 807-2861 FAX: (919) 807-2855 OSH Assistant Director (919) 807-2863 FAX: (919) 807-2856 Oregon Oregon Occupational Safety and Health Division Administrator (503) 378-3272 FAX: (503) 947-7461 Deputy Administrator for Policy (503) 378-3272 FAX: (503) 947-7461 Deputy Administrator for Operations (503) 378-3272 FAX: (503) 947-7461 Puerto Rico Puerto Rico Department of Labor and Human Resources Secretary (787) 754-2119 FAX: (787) 753-9550 Assistant Secretary for Occupational Safety and Health (787) 756-1100, 1106 / 754-2171 FAX: (787) 767-6051 Deputy Director for Occupational Safety and Health (787) 756-1100/1106, 754-2188 FAX: (787) 767-6051 South Carolina South Carolina Department of Labor, Licensing, and Regulation Director (803) 896-4300 FAX: (803) 896-4393 Program Director (803) 734-9644 FAX: (803) 734-9772 Tennessee Tennessee Department of Labor Commissioner (615) 741-2582 FAX: (615) 741-5078 Acting Program Director (615) 741-2793 FAX: (615) 741-3325 Utah Utah Labor Commission Commissioner (801) 530-6901 FAX: (801) 530-7906 Administrator (801) 530-6898 FAX: (801) 530-6390 Vermont Vermont Department of Labor and Industry Commissioner (802) 828-2288 FAX: (802) 828-2748 Project Manager (802) 828-2765 FAX: (802) 828-2195 Virgin Islands Virgin Islands Department of Labor Acting Commissioner (340) 773-1990 FAX: (340) 773-1858 Program Director (340) 772-1315 FAX: (340) 772-4323 Virginia Virginia Department of Labor and Industry Commissioner (804) 786-2377 FAX: (804) 371-6524 Director, Office of Legal Support (804) 786-9873 FAX: (804) 786-8418 Washington Washington Department of Labor and Industries Director (360) 902-4200 FAX: (360) 902-4202 Assistant Director (360) 902-5495 FAX: (360) 902-5529 Program Manager, Federal-State Operations (360) 902-5430 FAX: (360) 902-5529 Wyoming Wyoming Department of Employment Safety Administrator (307) 777-7786 FAX: (307) 777-3646 OSHA Onsite Consultation Offices Alabama (205) 348-3033 (205) 348-3049 FAX Alaska (907) 269-4957 (907) 269-4950 FAX Arizona (602) 542-1695 (602) 542-1614 FAX Arkansas (501) 682-4522 (501) 682-4532 FAX California (415) 703-5270 (415) 703-4596 FAX Colorado (970) 491-6151 (970) 491-7778 FAX Connecticut (860) 566-4550 (860) 566-6916 FAX Delaware (302) 761-8219 (302) 761-6601 FAX District of Columbia (202) 576-6339 (202) 576-7579 FAX Florida (813) 974-9962 Georgia (404) 894-2643 (404) 894-8275 FAX Guam 011 (671) 475-0136 011 (671) 477-2988 FAX Hawaii (808) 586-9100 (808) 586-9099 FAX Idaho (208) 426-3283 (208) 426-4411 FAX Illinois (312) 814-2337 (312) 814-7238 FAX Indiana (317) 232-2688 (317) 232-3790 FAX Iowa (515) 281-7629 (515) 281-5522 FAX Kansas (785) 296-7476 (785) 296-1775 FAX Kentucky (502) 564-6895 (502) 564-6103 FAX Louisiana (225) 342-9601 (225) 342-5158 FAX Maine (207) 624-6460 (207) 624-6449 FAX Maryland (410) 880-4970 (301) 483-8332 FAX Massachusetts (617) 727-3982 (617) 727-4581 FAX Michigan (517) 322-1809 (517) 322-1374 FAX Minnesota (612) 297-2393 (612) 297-1953 FAX Mississippi (601) 987-3981 (601) 987-3890 FAX Missouri (573) 751-3403 (573) 751-3721 FAX Montana (406) 444-6418 (406) 444-4140 FAX Nebraska (402) 471-4717 (402) 471-5039 FAX Nevada (702) 486-9140 (702) 990-0362 FAX New Hampshire (603) 271-2024 (603) 271-2667 FAX New Jersey (609) 292-3923 (609) 292-4409 FAX New Mexico (505) 827-4230 (505) 827-4422 FAX New York (518) 457-2238 (518) 457-3454 FAX North Carolina (919) 807-2905 (919) 807-2902 FAX North Dakota (701) 328-5188 (701) 328-5200 FAX Ohio (800) 282-1425 or (614) 644-2631 (614) 644-3133 FAX Oklahoma (405) 528-1500 (405) 528-5751 FAX Oregon (503) 378-3272 (503) 378-5729 FAX Pennsylvania (724) 357-2396 (724) 357-2385 FAX Puerto Rico (787) 754-2171 (787) 767-6051 FAX Rhode Island (401) 222-2438 (401) 222-2456 FAX South Carolina (803) 734-9614 (803) 734-9741 FAX South Dakota (605) 688-4101 (605) 688-6290 FAX Tennessee (615) 741-7036 (615) 532-2997 FAX Texas (512) 804-4640 (512) 804-4641 FAX OSHCON Request Line: (800) 687-7080 Utah (801) 530-6901 (801) 530-6992 FAX Vermont (802) 828-2765 (802) 828-2195 FAX Virginia (804) 786-6359 (804) 786-8418 FAX Virgin Islands (340) 772-1315 (340) 772-4323 FAX Washington (360) 902-5638 (360) 902-5459 FAX West Virginia (304) 558-7890 (304) 558-9711 FAX Wisconsin (Health) (608) 266-8579 (608) 266-9383 FAX Wisconsin (Safety) (262) 523-3040 (800) 947-0553 (262) 523-3046 FAX Wyoming (307) 777-7786 (307) 777-3646 FAX |
Back to Top | www.osha.gov | www.dol.gov |
Contact Us | Freedom of Information Act | Customer Survey Privacy and Security Statement | Disclaimers |
||
Occupational Safety & Health Administration 200 Constitution Avenue, NW Washington, DC 20210 |
Page last updated: 2005 |