1910.218(a) General requirements -
1910.218(a)(1) Use of lead. The safety requirements of this subparagraph apply to lead casts or other use of lead
in the forge shop or die shop.
1910.218(a)(1)(i) Thermostatic control of heating elements shall be provided to maintain proper melting temperature
and prevent overheating.
1910.218(a)(1)(ii) Fixed or permanent lead pot installations shall be exhausted.
1910.218(a)(1)(iii) Portable units shall be used only in areas where good, general room ventilation is
provided.
1910.218(a)(1)(iv) Personal protective equipment (gloves, goggles, aprons, and other items) shall be worn.
1910.218(a)(1)(v) A covered container shall be provided to store dross skimmings.
1910.218(a)(1)(vi) Equipment shall be kept clean, particularly from accumulations of yellow lead oxide.
..1910.218(a)(2)
1910.218(a)(2) Inspection and maintenance. It shall be the responsibility of the employer to maintain all forge
shop equipment in a condition which will insure continued safe operation. This responsibility includes:
1910.218(a)(2)(i) Establishing periodic and regular maintenance safety checks and keeping certification records of
these inspections which include the date of inspection, the signature of the person who performed the inspection and the serial number, or other
identifier, for the forging machine which was inspected.
1910.218(a)(2)(ii) Scheduling and recording the inspection of guards and point of operation protection devices at
frequent and regular intervals. Recording of inspections shall be in the form of a certification record which includes the date the inspection was
performed, the signature of the person who performed the inspection and the serial number, or other identifier, of the equipment inspected.
1910.218(a)(2)(iii) Training personnel for the proper inspection and maintenance of forging machinery and
equipment.
1910.218(a)(2)(iv) All overhead parts shall be fastened or protected in such a manner that they will not fly off or
fall in event of failure.
..1910.218(a)(3)
1910.218(a)(3) Hammers and presses.
1910.218(a)(3)(i) All hammers shall be positioned or installed in such a manner that they remain on or are anchored
to foundations sufficient to support them according to applicable engineering standards.
1910.218(a)(3)(ii) All presses shall be installed in such a manner that they remain where they are positioned or
they are anchored to foundations sufficient to support them according to applicable engineering standards.
TABLE O-11 - STRENGTH AND DIMENSIONS FOR WOOD RAM PROPS
_____________________________________________________________________
| | | | | |
Size of |Square |Minimum | Maximum |Safety| Maximum |Maximum
timber, |inches |allowable | static |factor| recommended |allowable
inches(1)| in |crushing | load | | weight of |length of
| cross |strength | within | | forging | timber,
|section|parallel | short | | hammer for | inches
| |to grain, | column | | timber used |
| |p.s.i.(2) | range(3)| | |
_________|_______|__________|_________|______|_____________|_________
| | | | | |
4 X 4 | 16 | 5,000 | 80,000 | 10 | 8,000 | 44
6 X 6 | 36 | 5,000 | 180,000 | 10 | 18,000 | 66
8 X 8 | 64 | 5,000 | 320,000 | 10 | 32,000 | 88
10 X 10 | 100 | 5,000 | 500,000 | 10 | 50,000 | 100
12 X 12 | 144 | 5,000 | 720,000 | 10 | 72,000 | 132
_________|_______|__________|_________|______|_____________|_________
Footnote(1) Actual dimension.
Footnote(2) Adapted from U.S. Department of Agriculture Technical
Bulletin 479. Hardwoods recommended are those whose ultimate crushing
strengths in compression parallel to grain are 5,000 p.s.i. (pounds
per square inch) or greater.
Footnote(3) Slenderness ratio formula for short columns is L/d=11,
where L=length of timber in inches and d=least dimension in inches;
this ratio should not exceed 11.
1910.218(a)(3)(iii) Means shall be provided for disconnecting the power to the machine and for locking out or
rendering cycling controls inoperable.
1910.218(a)(3)(iv) The ram shall be blocked when dies are being changed or other work is being done on the hammer.
Blocks or wedges shall be made of material the strength and construction of which should meet or exceed the specifications and dimensions shown in
Table O-11.
1910.218(a)(3)(v) Tongs shall be of sufficient length to clear the body of the worker in case of kickback, and
shall not have sharp handle ends.
1910.218(a)(3)(vi) Oil swabs, or scale removers, or other devices to remove scale shall be provided. These devices
shall be long enough to enable a man to reach the full length of the die without placing his hand or arm between the dies.
1910.218(a)(3)(vii) Material handling equipment shall be of adequate strength, size, and dimension to handle
diesetting operations safely.
..1910.218(a)(3)(viii)
1910.218(a)(3)(viii) A scale guard of substantial construction shall be provided at the back of every hammer, so
arranged as to stop flying scale.
1910.218(a)(3)(ix) A scale guard of substantial construction shall be provided at the back of every press, so
arranged as to stop flying scale.
1910.218(b) Hammers, general -
1910.218(b)(1) Keys. Die keys and shims shall be made from a grade of material that will not unduly crack or
splinter.
1910.218(b)(2) Foot operated devices. All foot operated devices (i.e., treadles, pedals, bars, valves, and
switches) shall be substantially and effectively protected from unintended operation.
1910.218(c) Presses. All manually operated valves and switches shall be clearly identified and readily
accessible.
1910.218(d) Power-driven hammers -
1910.218(d)(1) Safety cylinder head. Every steam or airhammer shall have a safety cylinder head to act as a cushion
if the rod should break or pullout of the ram.
..1910.218(d)(2)
1910.218(d)(2) Shutoff valve. Steam hammers shall be provided with a quick closing emergency valve in the admission
pipeline at a convenient location. This valve shall be closed and locked in the off position while the hammer is being adjusted, repaired, or
serviced, or when the dies are being changed.
1910.218(d)(3) Cylinder draining. Steam hammers shall be provided with a means of cylinder draining, such as a
self-draining arrangement or a quick-acting drain cock.
1910.218(d)(4) Pressure pipes. Steam or air piping shall conform to the specifications of American National
Standard ANSI B31.1.0-1967, Power Piping with Addenda issued before April 28, 1971, which is incorporated by reference as specified in Sec.
1910.6.
1910.218(e) Gravity hammers -
1910.218(e)(1) Air-lift hammers.
1910.218(e)(1)(i) Air-lift hammers shall have a safety cylinder head as required in paragraph (d)(1) of this
section.
1910.218(e)(1)(ii) Air-lift hammers shall have an air shutoff valve as required in paragraph (d)(2) of this
section.
1910.218(e)(1)(iii) Air-lift hammers shall be provided with two drain cocks: one on main head cylinder, and one on
clamp cylinder.
..1910.218(e)(1)(iv)
1910.218(e)(1)(iv) Air piping shall conform to the specifications of the ANSI B31.1.0-1967, Power Piping with
Addenda issued before April 28, 1971, which is incorporated by reference as specified in Sec. 1910.6.
1910.218(e)(2) Board drophammers.
1910.218(e)(2)(i) A suitable enclosure shall be provided to prevent damaged or detached boards from falling. The
board enclosure shall be securely fastened to the hammer.
1910.218(e)(2)(ii) All major assemblies and fittings which can loosen and fall shall be properly secured in
place.
1910.218(f) Forging presses -
1910.218(f)(1) Mechanical forging presses. When dies are being changed or maintenance is being performed on the
press, the following shall be accomplished:
1910.218(f)(1)(i) The power to the press shall be locked out.
1910.218(f)(1)(ii) The flywheel shall be at rest.
1910.218(f)(1)(iii) The ram shall be blocked with a material the strength of which shall meet or exceed the
specifications or dimensions shown in Table O-11.
1910.218(f)(2) Hydraulic forging presses. When dies are being changed or maintenance is being performed on the
press, the following shall be accomplished:
..1910.218(f)(2)(i)
1910.218(f)(2)(i) The hydraulic pumps and power apparatus shall be locked out.
1910.218(f)(2)(ii) The ram shall be blocked with a material the strength of which shall meet or exceed the
specifications or dimensions shown in Table O-11.
1910.218(g) Trimming presses -
1910.218(g)(1) Hot trimming presses. The requirements of paragraph (f)(1) of this section shall also apply to hot
trimming presses.
1910.218(g)(2) Cold trimming presses. Cold trimming presses shall be safeguarded in accordance with
1910.217(c).
1910.218(h) Upsetters -
1910.218(h)(1) General requirements. All upsetters shall be installed so that they remain on their supporting
foundations.
1910.218(h)(2) Lockouts. Upsetters shall be provided with a means for locking out the power at its entry point to
the machine and rendering its cycling controls inoperable.
1910.218(h)(3) Manually operated controls. All manually operated valves and switches shall be clearly identified
and readily accessible.
..1910.218(h)(4)
1910.218(h)(4) Tongs. Tongs shall be of sufficient length to clear the body of the worker in case of kickback, and
shall not have sharp handle ends.
1910.218(h)(5) Changing dies. When dies are being changed, maintenance performed, or any work done on the machine,
the power to the upsetter shall be locked out, and the flywheel shall be at rest.
1910.218(i) Other forging equipment -
1910.218(i)(1) Boltheading. The provisions of paragraph (h) of this section shall apply to boltheading.
1910.218(i)(2) Rivet making. The provisions of paragraph (h) of this section shall apply to rivet making.
1910.218(j) Other forge facility equipment-
1910.218(j)(1) Billet shears. A positive-type lockout device for disconnecting the power to the shear shall be
provided.
1910.218(j)(2) Saws. Every saw shall be provided with a guard of not less than one-eighth inch sheet metal
positioned to stop flying sparks.
1910.218(j)(3) Conveyors. Conveyor power transmission equipment shall be guarded in accordance with ANSI
B20.1-1957, Safety Code for Conveyors, Cableways, and Related Equipment, which is incorporated by reference as specified in Sec. 1910.6.
..1910.218(j)(4)
1910.218(j)(4) Shot blast. The cleaning chamber shall have doors or guards to protect operators.
1910.218(j)(5) Grinding. Personal protective equipment shall be used in grinding operations, and equipment shall be
used and maintained in accordance with ANSI B7.1-1970, Safety Code for the Use, Care, and Protection of Abrasive Wheels, which is incorporated by
reference as specified in Sec. 1910.6, and with 1910.215.
[39 FR 23502, June 27, 1974, as amended at 49 FR 5323, Feb. 10, 1984; 51 FR 34561, Sept. 29, 1986; 61 FR 9227, March 7, 1996]
|