|
Ionizing Radiation |
|
Standards |
|
|
|
Ionizing Radiation is addressed in specific standards for
the general industry, shipyard employment, and the construction industry. This
page highlights OSHA standards, directives (instructions for compliance
officers), standard interpretations (official letters of interpretation of the
standards), and other federal standards related to ionizing radiation.
OSHA
Section 5(a)(1) of the OSH Act, often referred to as the General Duty
Clause, requires employers to "furnish to each of his employees employment and a
place of employment which are free from recognized hazards that are causing or
are likely to cause death or serious physical harm to his employees". Section
5(a)(2) requires employers to "comply with occupational safety and health
standards promulgated under this Act".
Note:
Twenty-four states, Puerto Rico and the Virgin Islands, have
OSHA-approved State Plans and have adopted their own standards and
enforcement policies. For the most part, these States adopt standards that
are identical to Federal OSHA. However, some States have adopted different
standards applicable to this topic or may have different enforcement
policies. |
Highlighted Standards
General Industry (29
CFR 1910)
Shipyard Employment (29
CFR 1915)
-
1915 Subpart D, Welding, cutting, and heating
- 1915.57,
Uses of fissionable material in ship repairing and shipbuilding
Construction Industry (29
CFR 1926)
-
1926 Subpart D, Occupational health and environmental controls
- 1926.53,
Ionizing radiation (construction)
- 1926.65,
Hazardous waste operations and emergency response
Federal Register
Directives
Standard Interpretations
-
Workplace
exposure limits for ultra-violet radiation. (2003, February 26).
-
Occupational
exposure limits, access restrictions, and posting requirements for
airborne radioactive materials. (2002, December 23).
-
Applicable
OSHA standards and safety considerations for microwave device use in
a laboratory. (2002, August 8).
-
Video
Display Terminals (VDTs) and Radiation. (2000, January 19).
-
Correct
method for calculating whole body dose for ionizing radiation.
(1999, August 4).
-
Bloodborne Pathogens Standard applicability to radiopharmaceutical use. (1998, May
18).
- Maintenance of radiation exposure records NRC licensee contractors. (1998, February
23).
- Clarification of OSHA's Bloodborne Pathogens Standard as it relates to syringes and needles contaminated with both a bloodborne pathogen and radioactive nuclear medicine. (1996, October
29).
- Suggested state regulations for control of radiation. (1995, September
19).
- Male infertility and welding engineers. (1992, October
27). This interpretation includes a
discussion of ionizing radiation sources from various welding operations.
- Definition of an airborne radioactivity area. (1992, October
6).
- Definition of Reasonable Diligence as stated in 1910.1096(d)(1). (1991, April
17).
- Application of 1910.120 to emergency Responders at a nuclear power plants. (1991, January
28).
- Applicability of 1910.120 to the Uranium Mill Tailings Remedial Action Project. (1990, December
28).
- Ionizing radiation hazards in the workplace. (1990, September
27).
- Application of 1910.120 to cleanup of nuclear and hazardous waste. (1990, April
4).
- Clarification of the jurisdiction's of OSHA and the NRC in nuclear power plants. (1987, January
8).
- OSHA/NRC Interface Activities and Related Information. (1985, January
15).
- Review of permissible radiation exposure levels. (1984, November
5).
- Respirator air quality standards do not apply where the NRC has jurisdiction. (1979, March
6).
- Search all available
standard interpretations.
Other Federal
Note: These are NOT OSHA regulations. However, they do provide guidance from their originating organizations related to worker
protection.
Department of Energy (DOE)
Nuclear Regulatory Commission (NRC)
-
10
CFR 20, Standards for Protection Against Radiation
- 10
CFR 20, Appendices A-C (1971 version), 2.5 MB
PDF, 9 pages.
These appendices are referenced by OSHA standards 1910.1096,
1926.53, and 1915.57. The 1971 version
is the actual version enforceable by OSHA, not the most current
version.
|
|
|
|